diff options
Diffstat (limited to 'arch/arm/mach-at91/board-ek.c')
| -rw-r--r-- | arch/arm/mach-at91/board-ek.c | 199 |
1 files changed, 0 insertions, 199 deletions
diff --git a/arch/arm/mach-at91/board-ek.c b/arch/arm/mach-at91/board-ek.c deleted file mode 100644 index 56e92c4bbc2a..000000000000 --- a/arch/arm/mach-at91/board-ek.c +++ /dev/null @@ -1,199 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-ek.c - * - * Copyright (C) 2005 SAN People - * - * Epson S1D framebuffer glue code is: - * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include <linux/types.h> -#include <linux/init.h> -#include <linux/mm.h> -#include <linux/module.h> -#include <linux/platform_device.h> -#include <linux/spi/spi.h> -#include <linux/mtd/physmap.h> - -#include <asm/setup.h> -#include <asm/mach-types.h> -#include <asm/irq.h> - -#include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/irq.h> - -#include <mach/hardware.h> -#include <mach/board.h> -#include <mach/gpio.h> -#include <mach/at91rm9200_mc.h> - -#include "generic.h" - - -static void __init ek_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91rm9200_initialize(18432000, AT91RM9200_BGA); - - /* Setup the LEDs */ - at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init ek_init_irq(void) -{ - at91rm9200_init_interrupts(NULL); -} - -static struct at91_eth_data __initdata ek_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata ek_usbh_data = { - .ports = 2, -}; - -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin = AT91_PIN_PD4, - .pullup_pin = AT91_PIN_PD5, -}; - -static struct at91_mmc_data __initdata ek_mmc_data = { - .det_pin = AT91_PIN_PB27, - .slot_b = 0, - .wire4 = 1, - .wp_pin = AT91_PIN_PA17, -}; - -static struct spi_board_info ek_spi_devices[] = { - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - }, -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 3, - .max_speed_hz = 15 * 1000 * 1000, - }, -#endif -}; - -static struct i2c_board_info __initdata ek_i2c_devices[] = { - { - I2C_BOARD_INFO("ics1523", 0x26), - }, - { - I2C_BOARD_INFO("dac3550", 0x4d), - } -}; - -#define EK_FLASH_BASE AT91_CHIPSELECT_0 -#define EK_FLASH_SIZE SZ_2M - -static struct physmap_flash_data ek_flash_data = { - .width = 2, -}; - -static struct resource ek_flash_resource = { - .start = EK_FLASH_BASE, - .end = EK_FLASH_BASE + EK_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct platform_device ek_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &ek_flash_data, - }, - .resource = &ek_flash_resource, - .num_resources = 1, -}; - -static struct gpio_led ek_leds[] = { - { /* "user led 1", DS2 */ - .name = "green", - .gpio = AT91_PIN_PB0, - .active_low = 1, - .default_trigger = "mmc0", - }, - { /* "user led 2", DS4 */ - .name = "yellow", - .gpio = AT91_PIN_PB1, - .active_low = 1, - .default_trigger = "heartbeat", - }, - { /* "user led 3", DS6 */ - .name = "red", - .gpio = AT91_PIN_PB2, - .active_low = 1, - } -}; - -static void __init ek_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&ek_eth_data); - /* USB Host */ - at91_add_device_usbh(&ek_usbh_data); - /* USB Device */ - at91_add_device_udc(&ek_udc_data); - at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ - /* I2C */ - at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); - /* SPI */ - at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - /* DataFlash card */ - at91_set_gpio_output(AT91_PIN_PB22, 0); -#else - /* MMC */ - at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mmc(0, &ek_mmc_data); -#endif - /* NOR Flash */ - platform_device_register(&ek_flash); - /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); - /* VGA */ -// ek_add_device_video(); -} - -MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK") - /* Maintainer: SAN People/Atmel */ - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91rm9200_timer, - .map_io = ek_map_io, - .init_irq = ek_init_irq, - .init_machine = ek_board_init, -MACHINE_END |