1 files changed, 32 insertions, 13 deletions

diff --git a/arch/arm/mach-at91rm9200/board-dk.c b/arch/arm/mach-at91rm9200/board-dk.c
index 65873037e02a..c699f3984d4b 100644
--- a/arch/arm/mach-at91rm9200/board-dk.c
+++ b/arch/arm/mach-at91rm9200/board-dk.c
@@ -37,20 +37,11 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <asm/hardware.h>
 #include <asm/arch/board.h>
 #include <asm/arch/gpio.h>
 
 #include "generic.h"
 
-static void __init dk_init_irq(void)
-{
-	/* Initialize AIC controller */
-	at91rm9200_init_irq(NULL);
-
-	/* Set up the GPIO interrupts */
-	at91_gpio_irq_setup(BGA_GPIO_BANKS);
-}
 
 /*
  * Serial port configuration.
@@ -65,10 +56,8 @@ static struct at91_uart_config __initdata dk_uart_config = {
 
 static void __init dk_map_io(void)
 {
-	at91rm9200_map_io();
-
-	/* Initialize clocks: 18.432 MHz crystal */
-	at91_clock_init(18432000);
+	/* Initialize processor: 18.432 MHz crystal */
+	at91rm9200_initialize(18432000, AT91RM9200_BGA);
 
 	/* Setup the LEDs */
 	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
@@ -77,6 +66,11 @@ static void __init dk_map_io(void)
 	at91_init_serial(&dk_uart_config);
 }
 
+static void __init dk_init_irq(void)
+{
+	at91rm9200_init_interrupts(NULL);
+}
+
 static struct at91_eth_data __initdata dk_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
@@ -128,6 +122,29 @@ static struct spi_board_info dk_spi_devices[] = {
 #endif
 };
 
+static struct mtd_partition __initdata dk_nand_partition[] = {
+	{
+		.name	= "NAND Partition 1",
+		.offset	= 0,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(dk_nand_partition);
+	return dk_nand_partition;
+}
+
+static struct at91_nand_data __initdata dk_nand_data = {
+	.ale		= 22,
+	.cle		= 21,
+	.det_pin	= AT91_PIN_PB1,
+	.rdy_pin	= AT91_PIN_PC2,
+	// .enable_pin	= ... not there
+	.partition_info	= nand_partitions,
+};
+
 static void __init dk_board_init(void)
 {
 	/* Serial */
@@ -153,6 +170,8 @@ static void __init dk_board_init(void)
 	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
 	at91_add_device_mmc(&dk_mmc_data);
 #endif
+	/* NAND */
+	at91_add_device_nand(&dk_nand_data);
 	/* VGA */
 //	dk_add_device_video();
 }