diff options
Diffstat (limited to 'arch/v850/kernel/rte_me2_cb.c')
| -rw-r--r-- | arch/v850/kernel/rte_me2_cb.c | 298 |
1 files changed, 0 insertions, 298 deletions
diff --git a/arch/v850/kernel/rte_me2_cb.c b/arch/v850/kernel/rte_me2_cb.c deleted file mode 100644 index 46803d48dffe..000000000000 --- a/arch/v850/kernel/rte_me2_cb.c +++ /dev/null @@ -1,298 +0,0 @@ -/* - * arch/v850/kernel/rte_me2_cb.c -- Midas labs RTE-V850E/ME2-CB board - * - * Copyright (C) 2001,02,03 NEC Electronics Corporation - * Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org> - * - * This file is subject to the terms and conditions of the GNU General - * Public License. See the file COPYING in the main directory of this - * archive for more details. - * - * Written by Miles Bader <miles@gnu.org> - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/bootmem.h> -#include <linux/irq.h> -#include <linux/fs.h> -#include <linux/major.h> -#include <linux/sched.h> -#include <linux/delay.h> - -#include <asm/atomic.h> -#include <asm/page.h> -#include <asm/me2.h> -#include <asm/rte_me2_cb.h> -#include <asm/machdep.h> -#include <asm/v850e_intc.h> -#include <asm/v850e_cache.h> -#include <asm/irq.h> - -#include "mach.h" - -extern unsigned long *_intv_start; -extern unsigned long *_intv_end; - -/* LED access routines. */ -extern unsigned read_leds (int pos, char *buf, int len); -extern unsigned write_leds (int pos, const char *buf, int len); - - -/* SDRAM are almost contiguous (with a small hole in between; - see mach_reserve_bootmem for details), so just use both as one big area. */ -#define RAM_START SDRAM_ADDR -#define RAM_END (SDRAM_ADDR + SDRAM_SIZE) - - -void __init mach_get_physical_ram (unsigned long *ram_start, - unsigned long *ram_len) -{ - *ram_start = RAM_START; - *ram_len = RAM_END - RAM_START; -} - -void mach_gettimeofday (struct timespec *tv) -{ - tv->tv_sec = 0; - tv->tv_nsec = 0; -} - -/* Called before configuring an on-chip UART. */ -void rte_me2_cb_uart_pre_configure (unsigned chan, - unsigned cflags, unsigned baud) -{ - /* The RTE-V850E/ME2-CB connects some general-purpose I/O - pins on the CPU to the RTS/CTS lines of UARTB channel 0's - serial connection. - I/O pins P21 and P22 are RTS and CTS respectively. */ - if (chan == 0) { - /* Put P21 & P22 in I/O port mode. */ - ME2_PORT2_PMC &= ~0x6; - /* Make P21 and output, and P22 an input. */ - ME2_PORT2_PM = (ME2_PORT2_PM & ~0xC) | 0x4; - } - - me2_uart_pre_configure (chan, cflags, baud); -} - -void __init mach_init_irqs (void) -{ - /* Initialize interrupts. */ - me2_init_irqs (); - rte_me2_cb_init_irqs (); -} - -#ifdef CONFIG_ROM_KERNEL -/* Initialization for kernel in ROM. */ -static inline rom_kernel_init (void) -{ - /* If the kernel is in ROM, we have to copy any initialized data - from ROM into RAM. */ - extern unsigned long _data_load_start, _sdata, _edata; - register unsigned long *src = &_data_load_start; - register unsigned long *dst = &_sdata, *end = &_edata; - - while (dst != end) - *dst++ = *src++; -} -#endif /* CONFIG_ROM_KERNEL */ - -static void install_interrupt_vectors (void) -{ - unsigned long *p1, *p2; - - ME2_IRAMM = 0x03; /* V850E/ME2 iRAM write mode */ - - /* vector copy to iRAM */ - p1 = (unsigned long *)0; /* v85x vector start */ - p2 = (unsigned long *)&_intv_start; - while (p2 < (unsigned long *)&_intv_end) - *p1++ = *p2++; - - ME2_IRAMM = 0x00; /* V850E/ME2 iRAM read mode */ -} - -/* CompactFlash */ - -static void cf_power_on (void) -{ - /* CF card detected? */ - if (CB_CF_STS0 & 0x0030) - return; - - CB_CF_REG0 = 0x0002; /* reest on */ - mdelay (10); - CB_CF_REG0 = 0x0003; /* power on */ - mdelay (10); - CB_CF_REG0 = 0x0001; /* reset off */ - mdelay (10); -} - -static void cf_power_off (void) -{ - CB_CF_REG0 = 0x0003; /* power on */ - mdelay (10); - CB_CF_REG0 = 0x0002; /* reest on */ - mdelay (10); -} - -void __init mach_early_init (void) -{ - install_interrupt_vectors (); - - /* CS1 SDRAM instruction cache enable */ - v850e_cache_enable (0x04, 0x03, 0); - - rte_cb_early_init (); - - /* CompactFlash power on */ - cf_power_on (); - -#if defined (CONFIG_ROM_KERNEL) - rom_kernel_init (); -#endif -} - - -/* RTE-V850E/ME2-CB Programmable Interrupt Controller. */ - -static struct cb_pic_irq_init cb_pic_irq_inits[] = { - { "CB_EXTTM0", IRQ_CB_EXTTM0, 1, 1, 6 }, - { "CB_EXTSIO", IRQ_CB_EXTSIO, 1, 1, 6 }, - { "CB_TOVER", IRQ_CB_TOVER, 1, 1, 6 }, - { "CB_GINT0", IRQ_CB_GINT0, 1, 1, 6 }, - { "CB_USB", IRQ_CB_USB, 1, 1, 6 }, - { "CB_LANC", IRQ_CB_LANC, 1, 1, 6 }, - { "CB_USB_VBUS_ON", IRQ_CB_USB_VBUS_ON, 1, 1, 6 }, - { "CB_USB_VBUS_OFF", IRQ_CB_USB_VBUS_OFF, 1, 1, 6 }, - { "CB_EXTTM1", IRQ_CB_EXTTM1, 1, 1, 6 }, - { "CB_EXTTM2", IRQ_CB_EXTTM2, 1, 1, 6 }, - { 0 } -}; -#define NUM_CB_PIC_IRQ_INITS (ARRAY_SIZE(cb_pic_irq_inits) - 1) - -static struct hw_interrupt_type cb_pic_hw_itypes[NUM_CB_PIC_IRQ_INITS]; -static unsigned char cb_pic_active_irqs = 0; - -void __init rte_me2_cb_init_irqs (void) -{ - cb_pic_init_irq_types (cb_pic_irq_inits, cb_pic_hw_itypes); - - /* Initalize on board PIC1 (not PIC0) enable */ - CB_PIC_INT0M = 0x0000; - CB_PIC_INT1M = 0x0000; - CB_PIC_INTR = 0x0000; - CB_PIC_INTEN |= CB_PIC_INT1EN; - - ME2_PORT2_PMC |= 0x08; /* INTP23/SCK1 mode */ - ME2_PORT2_PFC &= ~0x08; /* INTP23 mode */ - ME2_INTR(2) &= ~0x08; /* INTP23 falling-edge detect */ - ME2_INTF(2) &= ~0x08; /* " */ - - rte_cb_init_irqs (); /* gbus &c */ -} - - -/* Enable interrupt handling for interrupt IRQ. */ -void cb_pic_enable_irq (unsigned irq) -{ - CB_PIC_INT1M |= 1 << (irq - CB_PIC_BASE_IRQ); -} - -void cb_pic_disable_irq (unsigned irq) -{ - CB_PIC_INT1M &= ~(1 << (irq - CB_PIC_BASE_IRQ)); -} - -void cb_pic_shutdown_irq (unsigned irq) -{ - cb_pic_disable_irq (irq); - - if (--cb_pic_active_irqs == 0) - free_irq (IRQ_CB_PIC, 0); - - CB_PIC_INT1M &= ~(1 << (irq - CB_PIC_BASE_IRQ)); -} - -static irqreturn_t cb_pic_handle_irq (int irq, void *dev_id, - struct pt_regs *regs) -{ - irqreturn_t rval = IRQ_NONE; - unsigned status = CB_PIC_INTR; - unsigned enable = CB_PIC_INT1M; - - /* Only pay attention to enabled interrupts. */ - status &= enable; - - CB_PIC_INTEN &= ~CB_PIC_INT1EN; - - if (status) { - unsigned mask = 1; - - irq = CB_PIC_BASE_IRQ; - do { - /* There's an active interrupt, find out which one, - and call its handler. */ - while (! (status & mask)) { - irq++; - mask <<= 1; - } - status &= ~mask; - - CB_PIC_INTR = mask; - - /* Recursively call handle_irq to handle it. */ - handle_irq (irq, regs); - rval = IRQ_HANDLED; - } while (status); - } - - CB_PIC_INTEN |= CB_PIC_INT1EN; - - return rval; -} - - -static void irq_nop (unsigned irq) { } - -static unsigned cb_pic_startup_irq (unsigned irq) -{ - int rval; - - if (cb_pic_active_irqs == 0) { - rval = request_irq (IRQ_CB_PIC, cb_pic_handle_irq, - IRQF_DISABLED, "cb_pic_handler", 0); - if (rval != 0) - return rval; - } - - cb_pic_active_irqs++; - - cb_pic_enable_irq (irq); - - return 0; -} - -/* Initialize HW_IRQ_TYPES for INTC-controlled irqs described in array - INITS (which is terminated by an entry with the name field == 0). */ -void __init cb_pic_init_irq_types (struct cb_pic_irq_init *inits, - struct hw_interrupt_type *hw_irq_types) -{ - struct cb_pic_irq_init *init; - for (init = inits; init->name; init++) { - struct hw_interrupt_type *hwit = hw_irq_types++; - - hwit->typename = init->name; - - hwit->startup = cb_pic_startup_irq; - hwit->shutdown = cb_pic_shutdown_irq; - hwit->enable = cb_pic_enable_irq; - hwit->disable = cb_pic_disable_irq; - hwit->ack = irq_nop; - hwit->end = irq_nop; - - /* Initialize kernel IRQ infrastructure for this interrupt. */ - init_irq_handlers(init->base, init->num, init->interval, hwit); - } -} |