diff options
Diffstat (limited to 'drivers/gpu/drm/amd/include/atomfirmware.h')
| -rw-r--r-- | drivers/gpu/drm/amd/include/atomfirmware.h | 114 |
1 files changed, 109 insertions, 5 deletions
diff --git a/drivers/gpu/drm/amd/include/atomfirmware.h b/drivers/gpu/drm/amd/include/atomfirmware.h index 70146518174c..b36ea8340afa 100644 --- a/drivers/gpu/drm/amd/include/atomfirmware.h +++ b/drivers/gpu/drm/amd/include/atomfirmware.h @@ -972,11 +972,13 @@ struct atom_ext_display_path }; //usCaps -enum ext_display_path_cap_def -{ - EXT_DISPLAY_PATH_CAPS__HBR2_DISABLE =0x0001, - EXT_DISPLAY_PATH_CAPS__DP_FIXED_VS_EN =0x0002, - EXT_DISPLAY_PATH_CAPS__EXT_CHIP_MASK =0x007C, +enum ext_display_path_cap_def { + EXT_DISPLAY_PATH_CAPS__HBR2_DISABLE = 0x0001, + EXT_DISPLAY_PATH_CAPS__DP_FIXED_VS_EN = 0x0002, + EXT_DISPLAY_PATH_CAPS__EXT_CHIP_MASK = 0x007C, + EXT_DISPLAY_PATH_CAPS__HDMI20_PI3EQX1204 = (0x01 << 2), //PI redriver chip + EXT_DISPLAY_PATH_CAPS__HDMI20_TISN65DP159RSBT = (0x02 << 2), //TI retimer chip + EXT_DISPLAY_PATH_CAPS__HDMI20_PARADE_PS175 = (0x03 << 2) //Parade DP->HDMI recoverter chip }; struct atom_external_display_connection_info @@ -1876,6 +1878,108 @@ struct atom_smc_dpm_info_v4_6 uint32_t boardreserved[10]; }; +struct atom_smc_dpm_info_v4_7 +{ + struct atom_common_table_header table_header; + // SECTION: BOARD PARAMETERS + // I2C Control + struct smudpm_i2c_controller_config_v2 I2cControllers[8]; + + // SVI2 Board Parameters + uint16_t MaxVoltageStepGfx; // In mV(Q2) Max voltage step that SMU will request. Multiple steps are taken if voltage change exceeds this value. + uint16_t MaxVoltageStepSoc; // In mV(Q2) Max voltage step that SMU will request. Multiple steps are taken if voltage change exceeds this value. + + uint8_t VddGfxVrMapping; // Use VR_MAPPING* bitfields + uint8_t VddSocVrMapping; // Use VR_MAPPING* bitfields + uint8_t VddMem0VrMapping; // Use VR_MAPPING* bitfields + uint8_t VddMem1VrMapping; // Use VR_MAPPING* bitfields + + uint8_t GfxUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode + uint8_t SocUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode + uint8_t ExternalSensorPresent; // External RDI connected to TMON (aka TEMP IN) + uint8_t Padding8_V; + + // Telemetry Settings + uint16_t GfxMaxCurrent; // in Amps + uint8_t GfxOffset; // in Amps + uint8_t Padding_TelemetryGfx; + uint16_t SocMaxCurrent; // in Amps + uint8_t SocOffset; // in Amps + uint8_t Padding_TelemetrySoc; + + uint16_t Mem0MaxCurrent; // in Amps + uint8_t Mem0Offset; // in Amps + uint8_t Padding_TelemetryMem0; + + uint16_t Mem1MaxCurrent; // in Amps + uint8_t Mem1Offset; // in Amps + uint8_t Padding_TelemetryMem1; + + // GPIO Settings + uint8_t AcDcGpio; // GPIO pin configured for AC/DC switching + uint8_t AcDcPolarity; // GPIO polarity for AC/DC switching + uint8_t VR0HotGpio; // GPIO pin configured for VR0 HOT event + uint8_t VR0HotPolarity; // GPIO polarity for VR0 HOT event + + uint8_t VR1HotGpio; // GPIO pin configured for VR1 HOT event + uint8_t VR1HotPolarity; // GPIO polarity for VR1 HOT event + uint8_t GthrGpio; // GPIO pin configured for GTHR Event + uint8_t GthrPolarity; // replace GPIO polarity for GTHR + + // LED Display Settings + uint8_t LedPin0; // GPIO number for LedPin[0] + uint8_t LedPin1; // GPIO number for LedPin[1] + uint8_t LedPin2; // GPIO number for LedPin[2] + uint8_t padding8_4; + + // GFXCLK PLL Spread Spectrum + uint8_t PllGfxclkSpreadEnabled; // on or off + uint8_t PllGfxclkSpreadPercent; // Q4.4 + uint16_t PllGfxclkSpreadFreq; // kHz + + // GFXCLK DFLL Spread Spectrum + uint8_t DfllGfxclkSpreadEnabled; // on or off + uint8_t DfllGfxclkSpreadPercent; // Q4.4 + uint16_t DfllGfxclkSpreadFreq; // kHz + + // UCLK Spread Spectrum + uint8_t UclkSpreadEnabled; // on or off + uint8_t UclkSpreadPercent; // Q4.4 + uint16_t UclkSpreadFreq; // kHz + + // SOCCLK Spread Spectrum + uint8_t SoclkSpreadEnabled; // on or off + uint8_t SocclkSpreadPercent; // Q4.4 + uint16_t SocclkSpreadFreq; // kHz + + // Total board power + uint16_t TotalBoardPower; //Only needed for TCP Estimated case, where TCP = TGP+Total Board Power + uint16_t BoardPadding; + + // Mvdd Svi2 Div Ratio Setting + uint32_t MvddRatio; // This is used for MVDD Vid workaround. It has 16 fractional bits (Q16.16) + + // GPIO pins for I2C communications with 2nd controller for Input Telemetry Sequence + uint8_t GpioI2cScl; // Serial Clock + uint8_t GpioI2cSda; // Serial Data + uint16_t GpioPadding; + + // Additional LED Display Settings + uint8_t LedPin3; // GPIO number for LedPin[3] - PCIE GEN Speed + uint8_t LedPin4; // GPIO number for LedPin[4] - PMFW Error Status + uint16_t LedEnableMask; + + // Power Limit Scalars + uint8_t PowerLimitScalar[4]; //[PPT_THROTTLER_COUNT] + + uint8_t MvddUlvPhaseSheddingMask; + uint8_t VddciUlvPhaseSheddingMask; + uint8_t Padding8_Psi1; + uint8_t Padding8_Psi2; + + uint32_t BoardReserved[5]; +}; + /* *************************************************************************** Data Table asic_profiling_info structure |