summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000e')
-rw-r--r--drivers/net/e1000e/defines.h2
-rw-r--r--drivers/net/e1000e/e1000.h26
-rw-r--r--drivers/net/e1000e/hw.h3
-rw-r--r--drivers/net/e1000e/ich8lan.c628
-rw-r--r--drivers/net/e1000e/phy.c476
5 files changed, 859 insertions, 276 deletions
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h
index c0f185beb8bc..1190167a8b3d 100644
--- a/drivers/net/e1000e/defines.h
+++ b/drivers/net/e1000e/defines.h
@@ -76,6 +76,7 @@
/* Extended Device Control */
#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
@@ -347,6 +348,7 @@
/* Extended Configuration Control and Size */
#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008
#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000
#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 981936c1fb46..189dfa2d6c76 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -141,6 +141,20 @@ struct e1000_info;
#define HV_TNCRS_UPPER PHY_REG(778, 29) /* Transmit with no CRS */
#define HV_TNCRS_LOWER PHY_REG(778, 30)
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS 17
+#define BM_CS_STATUS_LINK_UP 0x0400
+#define BM_CS_STATUS_RESOLVED 0x0800
+#define BM_CS_STATUS_SPEED_MASK 0xC000
+#define BM_CS_STATUS_SPEED_1000 0x8000
+
+/* 82577 Mobile Phy Status Register */
+#define HV_M_STATUS 26
+#define HV_M_STATUS_AUTONEG_COMPLETE 0x1000
+#define HV_M_STATUS_SPEED_MASK 0x0300
+#define HV_M_STATUS_SPEED_1000 0x0200
+#define HV_M_STATUS_LINK_UP 0x0040
+
enum e1000_boards {
board_82571,
board_82572,
@@ -519,9 +533,13 @@ extern s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
extern s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
extern s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
extern s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
+ u16 *data);
extern s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
extern s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
extern s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
+ u16 data);
extern s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
extern s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
extern s32 e1000e_get_cfg_done(struct e1000_hw *hw);
@@ -538,7 +556,11 @@ extern s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
extern s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
extern void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
extern s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset,
+ u16 data);
extern s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset,
+ u16 *data);
extern s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
u32 usec_interval, bool *success);
extern s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
@@ -546,7 +568,11 @@ extern s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
extern s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
extern s32 e1000e_check_downshift(struct e1000_hw *hw);
extern s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset,
+ u16 *data);
extern s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset,
+ u16 data);
extern s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow);
extern s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw);
extern s32 e1000_copper_link_setup_82577(struct e1000_hw *hw);
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index fd44d9f90769..aaea41ef794d 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -764,11 +764,13 @@ struct e1000_phy_operations {
s32 (*get_cable_length)(struct e1000_hw *);
s32 (*get_phy_info)(struct e1000_hw *);
s32 (*read_phy_reg)(struct e1000_hw *, u32, u16 *);
+ s32 (*read_phy_reg_locked)(struct e1000_hw *, u32, u16 *);
void (*release_phy)(struct e1000_hw *);
s32 (*reset_phy)(struct e1000_hw *);
s32 (*set_d0_lplu_state)(struct e1000_hw *, bool);
s32 (*set_d3_lplu_state)(struct e1000_hw *, bool);
s32 (*write_phy_reg)(struct e1000_hw *, u32, u16);
+ s32 (*write_phy_reg_locked)(struct e1000_hw *, u32, u16);
s32 (*cfg_on_link_up)(struct e1000_hw *);
};
@@ -901,6 +903,7 @@ struct e1000_shadow_ram {
struct e1000_dev_spec_ich8lan {
bool kmrn_lock_loss_workaround_enabled;
struct e1000_shadow_ram shadow_ram[E1000_ICH8_SHADOW_RAM_WORDS];
+ bool nvm_k1_enabled;
};
struct e1000_hw {
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index 99df2abf82a9..51ddb04ab195 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -122,6 +122,27 @@
#define HV_LED_CONFIG PHY_REG(768, 30) /* LED Configuration */
+#define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in milliseconds */
+
+/* SMBus Address Phy Register */
+#define HV_SMB_ADDR PHY_REG(768, 26)
+#define HV_SMB_ADDR_PEC_EN 0x0200
+#define HV_SMB_ADDR_VALID 0x0080
+
+/* Strapping Option Register - RO */
+#define E1000_STRAP 0x0000C
+#define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000
+#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
+
+/* OEM Bits Phy Register */
+#define HV_OEM_BITS PHY_REG(768, 25)
+#define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */
+#define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */
+#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
+
+#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
+#define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */
+
/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
/* Offset 04h HSFSTS */
union ich8_hws_flash_status {
@@ -200,6 +221,10 @@ static s32 e1000_setup_led_pchlan(struct e1000_hw *hw);
static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw);
static s32 e1000_led_on_pchlan(struct e1000_hw *hw);
static s32 e1000_led_off_pchlan(struct e1000_hw *hw);
+static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
+static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw);
+static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
+static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
{
@@ -242,7 +267,11 @@ static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
phy->ops.check_polarity = e1000_check_polarity_ife_ich8lan;
phy->ops.read_phy_reg = e1000_read_phy_reg_hv;
+ phy->ops.read_phy_reg_locked = e1000_read_phy_reg_hv_locked;
+ phy->ops.set_d0_lplu_state = e1000_set_lplu_state_pchlan;
+ phy->ops.set_d3_lplu_state = e1000_set_lplu_state_pchlan;
phy->ops.write_phy_reg = e1000_write_phy_reg_hv;
+ phy->ops.write_phy_reg_locked = e1000_write_phy_reg_hv_locked;
phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
phy->id = e1000_phy_unknown;
@@ -303,6 +332,8 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw)
case IGP03E1000_E_PHY_ID:
phy->type = e1000_phy_igp_3;
phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->ops.read_phy_reg_locked = e1000e_read_phy_reg_igp_locked;
+ phy->ops.write_phy_reg_locked = e1000e_write_phy_reg_igp_locked;
break;
case IFE_E_PHY_ID:
case IFE_PLUS_E_PHY_ID:
@@ -469,14 +500,6 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
goto out;
}
- if (hw->mac.type == e1000_pchlan) {
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_K1_CONFIG,
- E1000_KMRNCTRLSTA_K1_ENABLE);
- if (ret_val)
- goto out;
- }
-
/*
* First we want to see if the MII Status Register reports
* link. If so, then we want to get the current speed/duplex
@@ -486,6 +509,12 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
if (ret_val)
goto out;
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000_k1_gig_workaround_hv(hw, link);
+ if (ret_val)
+ goto out;
+ }
+
if (!link)
goto out; /* No link detected */
@@ -568,12 +597,39 @@ static s32 e1000_get_variants_ich8lan(struct e1000_adapter *adapter)
static DEFINE_MUTEX(nvm_mutex);
/**
+ * e1000_acquire_nvm_ich8lan - Acquire NVM mutex
+ * @hw: pointer to the HW structure
+ *
+ * Acquires the mutex for performing NVM operations.
+ **/
+static s32 e1000_acquire_nvm_ich8lan(struct e1000_hw *hw)
+{
+ mutex_lock(&nvm_mutex);
+
+ return 0;
+}
+
+/**
+ * e1000_release_nvm_ich8lan - Release NVM mutex
+ * @hw: pointer to the HW structure
+ *
+ * Releases the mutex used while performing NVM operations.
+ **/
+static void e1000_release_nvm_ich8lan(struct e1000_hw *hw)
+{
+ mutex_unlock(&nvm_mutex);
+
+ return;
+}
+
+static DEFINE_MUTEX(swflag_mutex);
+
+/**
* e1000_acquire_swflag_ich8lan - Acquire software control flag
* @hw: pointer to the HW structure
*
- * Acquires the software control flag for performing NVM and PHY
- * operations. This is a function pointer entry point only called by
- * read/write routines for the PHY and NVM parts.
+ * Acquires the software control flag for performing PHY and select
+ * MAC CSR accesses.
**/
static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
{
@@ -582,7 +638,7 @@ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
might_sleep();
- mutex_lock(&nvm_mutex);
+ mutex_lock(&swflag_mutex);
while (timeout) {
extcnf_ctrl = er32(EXTCNF_CTRL);
@@ -599,7 +655,7 @@ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
goto out;
}
- timeout = PHY_CFG_TIMEOUT * 2;
+ timeout = SW_FLAG_TIMEOUT;
extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
ew32(EXTCNF_CTRL, extcnf_ctrl);
@@ -623,7 +679,7 @@ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
out:
if (ret_val)
- mutex_unlock(&nvm_mutex);
+ mutex_unlock(&swflag_mutex);
return ret_val;
}
@@ -632,9 +688,8 @@ out:
* e1000_release_swflag_ich8lan - Release software control flag
* @hw: pointer to the HW structure
*
- * Releases the software control flag for performing NVM and PHY operations.
- * This is a function pointer entry point only called by read/write
- * routines for the PHY and NVM parts.
+ * Releases the software control flag for performing PHY and select
+ * MAC CSR accesses.
**/
static void e1000_release_swflag_ich8lan(struct e1000_hw *hw)
{
@@ -644,7 +699,9 @@ static void e1000_release_swflag_ich8lan(struct e1000_hw *hw)
extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
ew32(EXTCNF_CTRL, extcnf_ctrl);
- mutex_unlock(&nvm_mutex);
+ mutex_unlock(&swflag_mutex);
+
+ return;
}
/**
@@ -752,6 +809,326 @@ static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw)
}
/**
+ * e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ *
+ * SW should configure the LCD from the NVM extended configuration region
+ * as a workaround for certain parts.
+ **/
+static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask;
+ s32 ret_val;
+ u16 word_addr, reg_data, reg_addr, phy_page = 0;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Initialize the PHY from the NVM on ICH platforms. This
+ * is needed due to an issue where the NVM configuration is
+ * not properly autoloaded after power transitions.
+ * Therefore, after each PHY reset, we will load the
+ * configuration data out of the NVM manually.
+ */
+ if ((hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) ||
+ (hw->mac.type == e1000_pchlan)) {
+ struct e1000_adapter *adapter = hw->adapter;
+
+ /* Check if SW needs to configure the PHY */
+ if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
+ (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M) ||
+ (hw->mac.type == e1000_pchlan))
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
+ else
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
+
+ data = er32(FEXTNVM);
+ if (!(data & sw_cfg_mask))
+ goto out;
+
+ /* Wait for basic configuration completes before proceeding */
+ e1000_lan_init_done_ich8lan(hw);
+
+ /*
+ * Make sure HW does not configure LCD from PHY
+ * extended configuration before SW configuration
+ */
+ data = er32(EXTCNF_CTRL);
+ if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
+ goto out;
+
+ cnf_size = er32(EXTCNF_SIZE);
+ cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
+ cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
+ if (!cnf_size)
+ goto out;
+
+ cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
+ cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
+
+ if (!(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) &&
+ (hw->mac.type == e1000_pchlan)) {
+ /*
+ * HW configures the SMBus address and LEDs when the
+ * OEM and LCD Write Enable bits are set in the NVM.
+ * When both NVM bits are cleared, SW will configure
+ * them instead.
+ */
+ data = er32(STRAP);
+ data &= E1000_STRAP_SMBUS_ADDRESS_MASK;
+ reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT;
+ reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
+ ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ data = er32(LEDCTL);
+ ret_val = e1000_write_phy_reg_hv_locked(hw,
+ HV_LED_CONFIG,
+ (u16)data);
+ if (ret_val)
+ goto out;
+ }
+ /* Configure LCD from extended configuration region. */
+
+ /* cnf_base_addr is in DWORD */
+ word_addr = (u16)(cnf_base_addr << 1);
+
+ for (i = 0; i < cnf_size; i++) {
+ ret_val = e1000_read_nvm(hw, (word_addr + i * 2), 1,
+ &reg_data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000_read_nvm(hw, (word_addr + i * 2 + 1),
+ 1, &reg_addr);
+ if (ret_val)
+ goto out;
+
+ /* Save off the PHY page for future writes. */
+ if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
+ phy_page = reg_data;
+ continue;
+ }
+
+ reg_addr &= PHY_REG_MASK;
+ reg_addr |= phy_page;
+
+ ret_val = phy->ops.write_phy_reg_locked(hw,
+ (u32)reg_addr,
+ reg_data);
+ if (ret_val)
+ goto out;
+ }
+ }
+
+out:
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+}
+
+/**
+ * e1000_k1_gig_workaround_hv - K1 Si workaround
+ * @hw: pointer to the HW structure
+ * @link: link up bool flag
+ *
+ * If K1 is enabled for 1Gbps, the MAC might stall when transitioning
+ * from a lower speed. This workaround disables K1 whenever link is at 1Gig
+ * If link is down, the function will restore the default K1 setting located
+ * in the NVM.
+ **/
+static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link)
+{
+ s32 ret_val = 0;
+ u16 status_reg = 0;
+ bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled;
+
+ if (hw->mac.type != e1000_pchlan)
+ goto out;
+
+ /* Wrap the whole flow with the sw flag */
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ /* Disable K1 when link is 1Gbps, otherwise use the NVM setting */
+ if (link) {
+ if (hw->phy.type == e1000_phy_82578) {
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw,
+ BM_CS_STATUS,
+ &status_reg);
+ if (ret_val)
+ goto release;
+
+ status_reg &= BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_MASK;
+
+ if (status_reg == (BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_1000))
+ k1_enable = false;
+ }
+
+ if (hw->phy.type == e1000_phy_82577) {
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw,
+ HV_M_STATUS,
+ &status_reg);
+ if (ret_val)
+ goto release;
+
+ status_reg &= HV_M_STATUS_LINK_UP |
+ HV_M_STATUS_AUTONEG_COMPLETE |
+ HV_M_STATUS_SPEED_MASK;
+
+ if (status_reg == (HV_M_STATUS_LINK_UP |
+ HV_M_STATUS_AUTONEG_COMPLETE |
+ HV_M_STATUS_SPEED_1000))
+ k1_enable = false;
+ }
+
+ /* Link stall fix for link up */
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19),
+ 0x0100);
+ if (ret_val)
+ goto release;
+
+ } else {
+ /* Link stall fix for link down */
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19),
+ 0x4100);
+ if (ret_val)
+ goto release;
+ }
+
+ ret_val = e1000_configure_k1_ich8lan(hw, k1_enable);
+
+release:
+ hw->phy.ops.release_phy(hw);
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_configure_k1_ich8lan - Configure K1 power state
+ * @hw: pointer to the HW structure
+ * @enable: K1 state to configure
+ *
+ * Configure the K1 power state based on the provided parameter.
+ * Assumes semaphore already acquired.
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ **/
+static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
+{
+ s32 ret_val = 0;
+ u32 ctrl_reg = 0;
+ u32 ctrl_ext = 0;
+ u32 reg = 0;
+ u16 kmrn_reg = 0;
+
+ ret_val = e1000e_read_kmrn_reg_locked(hw,
+ E1000_KMRNCTRLSTA_K1_CONFIG,
+ &kmrn_reg);
+ if (ret_val)
+ goto out;
+
+ if (k1_enable)
+ kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE;
+ else
+ kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE;
+
+ ret_val = e1000e_write_kmrn_reg_locked(hw,
+ E1000_KMRNCTRLSTA_K1_CONFIG,
+ kmrn_reg);
+ if (ret_val)
+ goto out;
+
+ udelay(20);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_reg = er32(CTRL);
+
+ reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ reg |= E1000_CTRL_FRCSPD;
+ ew32(CTRL, reg);
+
+ ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_SPD_BYPS);
+ udelay(20);
+ ew32(CTRL, ctrl_reg);
+ ew32(CTRL_EXT, ctrl_ext);
+ udelay(20);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_oem_bits_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ * @d0_state: boolean if entering d0 or d3 device state
+ *
+ * SW will configure Gbe Disable and LPLU based on the NVM. The four bits are
+ * collectively called OEM bits. The OEM Write Enable bit and SW Config bit
+ * in NVM determines whether HW should configure LPLU and Gbe Disable.
+ **/
+static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
+{
+ s32 ret_val = 0;
+ u32 mac_reg;
+ u16 oem_reg;
+
+ if (hw->mac.type != e1000_pchlan)
+ return ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ mac_reg = er32(EXTCNF_CTRL);
+ if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE)
+ goto out;
+
+ mac_reg = er32(FEXTNVM);
+ if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M))
+ goto out;
+
+ mac_reg = er32(PHY_CTRL);
+
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw, HV_OEM_BITS, &oem_reg);
+ if (ret_val)
+ goto out;
+
+ oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU);
+
+ if (d0_state) {
+ if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_D0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ } else {
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ }
+ /* Restart auto-neg to activate the bits */
+ oem_reg |= HV_OEM_BITS_RESTART_AN;
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, HV_OEM_BITS, oem_reg);
+
+out:
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+
+/**
* e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be
* done after every PHY reset.
**/
@@ -791,10 +1168,20 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
ret_val = hw->phy.ops.acquire_phy(hw);
if (ret_val)
return ret_val;
+
hw->phy.addr = 1;
- e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+ if (ret_val)
+ goto out;
hw->phy.ops.release_phy(hw);
+ /*
+ * Configure the K1 Si workaround during phy reset assuming there is
+ * link so that it disables K1 if link is in 1Gbps.
+ */
+ ret_val = e1000_k1_gig_workaround_hv(hw, true);
+
+out:
return ret_val;
}
@@ -840,11 +1227,8 @@ static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw)
**/
static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
{
- struct e1000_phy_info *phy = &hw->phy;
- u32 i;
- u32 data, cnf_size, cnf_base_addr, sw_cfg_mask;
- s32 ret_val;
- u16 word_addr, reg_data, reg_addr, phy_page = 0;
+ s32 ret_val = 0;
+ u16 reg;
ret_val = e1000e_phy_hw_reset_generic(hw);
if (ret_val)
@@ -859,81 +1243,20 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
return ret_val;
}
- /*
- * Initialize the PHY from the NVM on ICH platforms. This
- * is needed due to an issue where the NVM configuration is
- * not properly autoloaded after power transitions.
- * Therefore, after each PHY reset, we will load the
- * configuration data out of the NVM manually.
- */
- if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) {
- struct e1000_adapter *adapter = hw->adapter;
-
- /* Check if SW needs configure the PHY */
- if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
- (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M))
- sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
- else
- sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
-
- data = er32(FEXTNVM);
- if (!(data & sw_cfg_mask))
- return 0;
-
- /* Wait for basic configuration completes before proceeding */
- e1000_lan_init_done_ich8lan(hw);
-
- /*
- * Make sure HW does not configure LCD from PHY
- * extended configuration before SW configuration
- */
- data = er32(EXTCNF_CTRL);
- if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
- return 0;
-
- cnf_size = er32(EXTCNF_SIZE);
- cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
- cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
- if (!cnf_size)
- return 0;
-
- cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
- cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
-
- /* Configure LCD from extended configuration region. */
-
- /* cnf_base_addr is in DWORD */
- word_addr = (u16)(cnf_base_addr << 1);
-
- for (i = 0; i < cnf_size; i++) {
- ret_val = e1000_read_nvm(hw,
- (word_addr + i * 2),
- 1,
- &reg_data);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_nvm(hw,
- (word_addr + i * 2 + 1),
- 1,
- &reg_addr);
- if (ret_val)
- return ret_val;
-
- /* Save off the PHY page for future writes. */
- if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
- phy_page = reg_data;
- continue;
- }
+ /* Dummy read to clear the phy wakeup bit after lcd reset */
+ if (hw->mac.type == e1000_pchlan)
+ e1e_rphy(hw, BM_WUC, &reg);
- reg_addr |= phy_page;
+ /* Configure the LCD with the extended configuration region in NVM */
+ ret_val = e1000_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
- ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data);
- if (ret_val)
- return ret_val;
- }
- }
+ /* Configure the LCD with the OEM bits in NVM */
+ if (hw->mac.type == e1000_pchlan)
+ ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+out:
return 0;
}
@@ -1054,6 +1377,38 @@ static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw)
}
/**
+ * e1000_set_lplu_state_pchlan - Set Low Power Link Up state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU state according to the active flag. For PCH, if OEM write
+ * bit are disabled in the NVM, writing the LPLU bits in the MAC will not set
+ * the phy speed. This function will manually set the LPLU bit and restart
+ * auto-neg as hw would do. D3 and D0 LPLU will call the same function
+ * since it configures the same bit.
+ **/
+static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active)
+{
+ s32 ret_val = 0;
+ u16 oem_reg;
+
+ ret_val = e1e_rphy(hw, HV_OEM_BITS, &oem_reg);
+ if (ret_val)
+ goto out;
+
+ if (active)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ else
+ oem_reg &= ~HV_OEM_BITS_LPLU;
+
+ oem_reg |= HV_OEM_BITS_RESTART_AN;
+ ret_val = e1e_wphy(hw, HV_OEM_BITS, oem_reg);
+
+out:
+ return ret_val;
+}
+
+/**
* e1000_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state
* @hw: pointer to the HW structure
* @active: TRUE to enable LPLU, FALSE to disable
@@ -1314,12 +1669,11 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
(words == 0)) {
hw_dbg(hw, "nvm parameter(s) out of bounds\n");
- return -E1000_ERR_NVM;
+ ret_val = -E1000_ERR_NVM;
+ goto out;
}
- ret_val = e1000_acquire_swflag_ich8lan(hw);
- if (ret_val)
- goto out;
+ nvm->ops.acquire_nvm(hw);
ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
if (ret_val) {
@@ -1345,7 +1699,7 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
}
}
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
out:
if (ret_val)
@@ -1603,11 +1957,15 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
return -E1000_ERR_NVM;
}
+ nvm->ops.acquire_nvm(hw);
+
for (i = 0; i < words; i++) {
dev_spec->shadow_ram[offset+i].modified = 1;
dev_spec->shadow_ram[offset+i].value = data[i];
}
+ nvm->ops.release_nvm(hw);
+
return 0;
}
@@ -1637,9 +1995,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
if (nvm->type != e1000_nvm_flash_sw)
goto out;
- ret_val = e1000_acquire_swflag_ich8lan(hw);
- if (ret_val)
- goto out;
+ nvm->ops.acquire_nvm(hw);
/*
* We're writing to the opposite bank so if we're on bank 1,
@@ -1657,7 +2013,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
old_bank_offset = 0;
ret_val = e1000_erase_flash_bank_ich8lan(hw, 1);
if (ret_val) {
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
goto out;
}
} else {
@@ -1665,7 +2021,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
new_bank_offset = 0;
ret_val = e1000_erase_flash_bank_ich8lan(hw, 0);
if (ret_val) {
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
goto out;
}
}
@@ -1723,7 +2079,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
if (ret_val) {
/* Possibly read-only, see e1000e_write_protect_nvm_ich8lan() */
hw_dbg(hw, "Flash commit failed.\n");
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
goto out;
}
@@ -1736,7 +2092,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD;
ret_val = e1000_read_flash_word_ich8lan(hw, act_offset, &data);
if (ret_val) {
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
goto out;
}
data &= 0xBFFF;
@@ -1744,7 +2100,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
act_offset * 2 + 1,
(u8)(data >> 8));
if (ret_val) {
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
goto out;
}
@@ -1757,7 +2113,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1;
ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset, 0);
if (ret_val) {
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
goto out;
}
@@ -1767,7 +2123,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
dev_spec->shadow_ram[i].value = 0xFFFF;
}
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
/*
* Reload the EEPROM, or else modifications will not appear
@@ -1831,14 +2187,12 @@ static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw)
**/
void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw)
{
+ struct e1000_nvm_info *nvm = &hw->nvm;
union ich8_flash_protected_range pr0;
union ich8_hws_flash_status hsfsts;
u32 gfpreg;
- s32 ret_val;
- ret_val = e1000_acquire_swflag_ich8lan(hw);
- if (ret_val)
- return;
+ nvm->ops.acquire_nvm(hw);
gfpreg = er32flash(ICH_FLASH_GFPREG);
@@ -1859,7 +2213,7 @@ void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw)
hsfsts.hsf_status.flockdn = true;
ew32flash(ICH_FLASH_HSFSTS, hsfsts.regval);
- e1000_release_swflag_ich8lan(hw);
+ nvm->ops.release_nvm(hw);
}
/**
@@ -2229,6 +2583,8 @@ static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw)
**/
static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
{
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u16 reg;
u32 ctrl, icr, kab;
s32 ret_val;
@@ -2263,6 +2619,18 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
ew32(PBS, E1000_PBS_16K);
}
+ if (hw->mac.type == e1000_pchlan) {
+ /* Save the NVM K1 bit setting*/
+ ret_val = e1000_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, &reg);
+ if (ret_val)
+ return ret_val;
+
+ if (reg & E1000_NVM_K1_ENABLE)
+ dev_spec->nvm_k1_enabled = true;
+ else
+ dev_spec->nvm_k1_enabled = false;
+ }
+
ctrl = er32(CTRL);
if (!e1000_check_reset_block(hw)) {
@@ -2304,7 +2672,19 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
hw_dbg(hw, "Auto Read Done did not complete\n");
}
}
+ /* Dummy read to clear the phy wakeup bit after lcd reset */
+ if (hw->mac.type == e1000_pchlan)
+ e1e_rphy(hw, BM_WUC, &reg);
+ ret_val = e1000_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
+
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+ if (ret_val)
+ goto out;
+ }
/*
* For PCH, this write will make sure that any noise
* will be detected as a CRC error and be dropped rather than show up
@@ -2323,6 +2703,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
if (hw->mac.type == e1000_pchlan)
ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
+out:
return ret_val;
}
@@ -2627,14 +3008,6 @@ static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed,
if (ret_val)
return ret_val;
- if ((hw->mac.type == e1000_pchlan) && (*speed == SPEED_1000)) {
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_K1_CONFIG,
- E1000_KMRNCTRLSTA_K1_DISABLE);
- if (ret_val)
- return ret_val;
- }
-
if ((hw->mac.type == e1000_ich8lan) &&
(hw->phy.type == e1000_phy_igp_3) &&
(*speed == SPEED_1000)) {
@@ -2843,9 +3216,8 @@ void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
E1000_PHY_CTRL_GBE_DISABLE;
ew32(PHY_CTRL, phy_ctrl);
- /* Workaround SWFLAG unexpectedly set during S0->Sx */
if (hw->mac.type == e1000_pchlan)
- udelay(500);
+ e1000_phy_hw_reset_ich8lan(hw);
default:
break;
}
@@ -3113,9 +3485,9 @@ static struct e1000_phy_operations ich8_phy_ops = {
};
static struct e1000_nvm_operations ich8_nvm_ops = {
- .acquire_nvm = e1000_acquire_swflag_ich8lan,
+ .acquire_nvm = e1000_acquire_nvm_ich8lan,
.read_nvm = e1000_read_nvm_ich8lan,
- .release_nvm = e1000_release_swflag_ich8lan,
+ .release_nvm = e1000_release_nvm_ich8lan,
.update_nvm = e1000_update_nvm_checksum_ich8lan,
.valid_led_default = e1000_valid_led_default_ich8lan,
.validate_nvm = e1000_validate_nvm_checksum_ich8lan,
diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index 994401fd0664..03175b3a2c9e 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -95,13 +95,6 @@ static const u16 e1000_igp_2_cable_length_table[] =
/* BM PHY Copper Specific Control 1 */
#define BM_CS_CTRL1 16
-/* BM PHY Copper Specific Status */
-#define BM_CS_STATUS 17
-#define BM_CS_STATUS_LINK_UP 0x0400
-#define BM_CS_STATUS_RESOLVED 0x0800
-#define BM_CS_STATUS_SPEED_MASK 0xC000
-#define BM_CS_STATUS_SPEED_1000 0x8000
-
#define HV_MUX_DATA_CTRL PHY_REG(776, 16)
#define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400
#define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004
@@ -164,16 +157,25 @@ s32 e1000e_get_phy_id(struct e1000_hw *hw)
* MDIC mode. No harm in trying again in this case since
* the PHY ID is unknown at this point anyway
*/
+ ret_val = phy->ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
ret_val = e1000_set_mdio_slow_mode_hv(hw, true);
if (ret_val)
goto out;
+ phy->ops.release_phy(hw);
retry_count++;
}
out:
/* Revert to MDIO fast mode, if applicable */
- if (retry_count)
+ if (retry_count) {
+ ret_val = phy->ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+ phy->ops.release_phy(hw);
+ }
return ret_val;
}
@@ -354,94 +356,173 @@ s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data)
}
/**
- * e1000e_read_phy_reg_igp - Read igp PHY register
+ * __e1000e_read_phy_reg_igp - Read igp PHY register
* @hw: pointer to the HW structure
* @offset: register offset to be read
* @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary, then reads the PHY register at offset
- * and storing the retrieved information in data. Release any acquired
+ * and stores the retrieved information in data. Release any acquired
* semaphores before exiting.
**/
-s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data)
+static s32 __e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
{
- s32 ret_val;
+ s32 ret_val = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
+ if (!locked) {
+ if (!(hw->phy.ops.acquire_phy))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+ }
if (offset > MAX_PHY_MULTI_PAGE_REG) {
ret_val = e1000e_write_phy_reg_mdic(hw,
IGP01E1000_PHY_PAGE_SELECT,
(u16)offset);
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- return ret_val;
- }
+ if (ret_val)
+ goto release;
}
ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
- data);
-
- hw->phy.ops.release_phy(hw);
+ data);
+release:
+ if (!locked)
+ hw->phy.ops.release_phy(hw);
+out:
return ret_val;
}
/**
+ * e1000e_read_phy_reg_igp - Read igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset and stores the
+ * retrieved information in data.
+ * Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_phy_reg_igp(hw, offset, data, false);
+}
+
+/**
+ * e1000e_read_phy_reg_igp_locked - Read igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset and stores the retrieved information
+ * in data. Assumes semaphore already acquired.
+ **/
+s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000e_read_phy_reg_igp(hw, offset, data, true);
+}
+
+/**
* e1000e_write_phy_reg_igp - Write igp PHY register
* @hw: pointer to the HW structure
* @offset: register offset to write to
* @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary, then writes the data to PHY register
* at the offset. Release any acquired semaphores before exiting.
**/
-s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data)
+static s32 __e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
{
- s32 ret_val;
+ s32 ret_val = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
+ if (!locked) {
+ if (!(hw->phy.ops.acquire_phy))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+ }
if (offset > MAX_PHY_MULTI_PAGE_REG) {
ret_val = e1000e_write_phy_reg_mdic(hw,
IGP01E1000_PHY_PAGE_SELECT,
(u16)offset);
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- return ret_val;
- }
+ if (ret_val)
+ goto release;
}
ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
data);
- hw->phy.ops.release_phy(hw);
+release:
+ if (!locked)
+ hw->phy.ops.release_phy(hw);
+out:
return ret_val;
}
/**
- * e1000e_read_kmrn_reg - Read kumeran register
+ * e1000e_write_phy_reg_igp - Write igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_phy_reg_igp(hw, offset, data, false);
+}
+
+/**
+ * e1000e_write_phy_reg_igp_locked - Write igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes the data to PHY register at the offset.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000e_write_phy_reg_igp(hw, offset, data, true);
+}
+
+/**
+ * __e1000_read_kmrn_reg - Read kumeran register
* @hw: pointer to the HW structure
* @offset: register offset to be read
* @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary. Then reads the PHY register at offset
* using the kumeran interface. The information retrieved is stored in data.
* Release any acquired semaphores before exiting.
**/
-s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
+static s32 __e1000_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
{
u32 kmrnctrlsta;
- s32 ret_val;
+ s32 ret_val = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
+ if (!locked) {
+ if (!(hw->phy.ops.acquire_phy))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+ }
kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
@@ -452,41 +533,111 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
kmrnctrlsta = er32(KMRNCTRLSTA);
*data = (u16)kmrnctrlsta;
- hw->phy.ops.release_phy(hw);
+ if (!locked)
+ hw->phy.ops.release_phy(hw);
+out:
return ret_val;
}
/**
- * e1000e_write_kmrn_reg - Write kumeran register
+ * e1000e_read_kmrn_reg - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset using the
+ * kumeran interface. The information retrieved is stored in data.
+ * Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_kmrn_reg(hw, offset, data, false);
+}
+
+/**
+ * e1000e_read_kmrn_reg_locked - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset using the kumeran interface. The
+ * information retrieved is stored in data.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_kmrn_reg(hw, offset, data, true);
+}
+
+/**
+ * __e1000_write_kmrn_reg - Write kumeran register
* @hw: pointer to the HW structure
* @offset: register offset to write to
* @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary. Then write the data to PHY register
* at the offset using the kumeran interface. Release any acquired semaphores
* before exiting.
**/
-s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
+static s32 __e1000_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
{
u32 kmrnctrlsta;
- s32 ret_val;
+ s32 ret_val = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
+ if (!locked) {
+ if (!(hw->phy.ops.acquire_phy))
+ goto out;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+ }
kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
E1000_KMRNCTRLSTA_OFFSET) | data;
ew32(KMRNCTRLSTA, kmrnctrlsta);
udelay(2);
- hw->phy.ops.release_phy(hw);
+ if (!locked)
+ hw->phy.ops.release_phy(hw);
+
+out:
return ret_val;
}
/**
+ * e1000e_write_kmrn_reg - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to the PHY register at the offset
+ * using the kumeran interface. Release the acquired semaphore before exiting.
+ **/
+s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_kmrn_reg(hw, offset, data, false);
+}
+
+/**
+ * e1000e_write_kmrn_reg_locked - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Write the data to PHY register at the offset using the kumeran interface.
+ * Assumes semaphore already acquired.
+ **/
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_kmrn_reg(hw, offset, data, true);
+}
+
+/**
* e1000_copper_link_setup_82577 - Setup 82577 PHY for copper link
* @hw: pointer to the HW structure
*
@@ -2105,6 +2256,10 @@ s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data)
u32 page = offset >> IGP_PAGE_SHIFT;
u32 page_shift = 0;
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
@@ -2112,10 +2267,6 @@ s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data)
goto out;
}
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- goto out;
-
hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset);
if (offset > MAX_PHY_MULTI_PAGE_REG) {
@@ -2135,18 +2286,15 @@ s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data)
/* Page is shifted left, PHY expects (page x 32) */
ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
(page << page_shift));
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
+ if (ret_val)
goto out;
- }
}
ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
data);
- hw->phy.ops.release_phy(hw);
-
out:
+ hw->phy.ops.release_phy(hw);
return ret_val;
}
@@ -2167,6 +2315,10 @@ s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data)
u32 page = offset >> IGP_PAGE_SHIFT;
u32 page_shift = 0;
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
@@ -2174,10 +2326,6 @@ s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data)
goto out;
}
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- goto out;
-
hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset);
if (offset > MAX_PHY_MULTI_PAGE_REG) {
@@ -2197,17 +2345,14 @@ s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data)
/* Page is shifted left, PHY expects (page x 32) */
ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
(page << page_shift));
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
+ if (ret_val)
goto out;
- }
}
ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
data);
- hw->phy.ops.release_phy(hw);
-
out:
+ hw->phy.ops.release_phy(hw);
return ret_val;
}
@@ -2226,17 +2371,17 @@ s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data)
s32 ret_val;
u16 page = (u16)(offset >> IGP_PAGE_SHIFT);
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
true);
- return ret_val;
+ goto out;
}
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
-
hw->phy.addr = 1;
if (offset > MAX_PHY_MULTI_PAGE_REG) {
@@ -2245,16 +2390,14 @@ s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data)
ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
page);
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- return ret_val;
- }
+ if (ret_val)
+ goto out;
}
ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
data);
+out:
hw->phy.ops.release_phy(hw);
-
return ret_val;
}
@@ -2272,17 +2415,17 @@ s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data)
s32 ret_val;
u16 page = (u16)(offset >> IGP_PAGE_SHIFT);
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
false);
- return ret_val;
+ goto out;
}
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
-
hw->phy.addr = 1;
if (offset > MAX_PHY_MULTI_PAGE_REG) {
@@ -2290,17 +2433,15 @@ s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data)
ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
page);
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- return ret_val;
- }
+ if (ret_val)
+ goto out;
}
ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
data);
+out:
hw->phy.ops.release_phy(hw);
-
return ret_val;
}
@@ -2320,6 +2461,8 @@ s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data)
* 3) Write the address using the address opcode (0x11)
* 4) Read or write the data using the data opcode (0x12)
* 5) Restore 769_17.2 to its original value
+ *
+ * Assumes semaphore already acquired.
**/
static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
u16 *data, bool read)
@@ -2327,20 +2470,12 @@ static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
s32 ret_val;
u16 reg = BM_PHY_REG_NUM(offset);
u16 phy_reg = 0;
- u8 phy_acquired = 1;
-
/* Gig must be disabled for MDIO accesses to page 800 */
if ((hw->mac.type == e1000_pchlan) &&
(!(er32(PHY_CTRL) & E1000_PHY_CTRL_GBE_DISABLE)))
hw_dbg(hw, "Attempting to access page 800 while gig enabled\n");
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val) {
- phy_acquired = 0;
- goto out;
- }
-
/* All operations in this function are phy address 1 */
hw->phy.addr = 1;
@@ -2397,8 +2532,6 @@ static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
out:
- if (phy_acquired == 1)
- hw->phy.ops.release_phy(hw);
return ret_val;
}
@@ -2439,52 +2572,63 @@ static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
return 0;
}
+/**
+ * e1000_set_mdio_slow_mode_hv - Set slow MDIO access mode
+ * @hw: pointer to the HW structure
+ * @slow: true for slow mode, false for normal mode
+ *
+ * Assumes semaphore already acquired.
+ **/
s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw, bool slow)
{
s32 ret_val = 0;
u16 data = 0;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- return ret_val;
-
/* Set MDIO mode - page 769, register 16: 0x2580==slow, 0x2180==fast */
hw->phy.addr = 1;
ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
(BM_PORT_CTRL_PAGE << IGP_PAGE_SHIFT));
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- return ret_val;
- }
+ if (ret_val)
+ goto out;
+
ret_val = e1000e_write_phy_reg_mdic(hw, BM_CS_CTRL1,
(0x2180 | (slow << 10)));
+ if (ret_val)
+ goto out;
/* dummy read when reverting to fast mode - throw away result */
if (!slow)
- e1000e_read_phy_reg_mdic(hw, BM_CS_CTRL1, &data);
-
- hw->phy.ops.release_phy(hw);
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_CS_CTRL1, &data);
+out:
return ret_val;
}
/**
- * e1000_read_phy_reg_hv - Read HV PHY register
+ * __e1000_read_phy_reg_hv - Read HV PHY register
* @hw: pointer to the HW structure
* @offset: register offset to be read
* @data: pointer to the read data
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary, then reads the PHY register at offset
- * and storing the retrieved information in data. Release any acquired
+ * and stores the retrieved information in data. Release any acquired
* semaphore before exiting.
**/
-s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
+static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
+ bool locked)
{
s32 ret_val;
u16 page = BM_PHY_REG_PAGE(offset);
u16 reg = BM_PHY_REG_NUM(offset);
bool in_slow_mode = false;
+ if (!locked) {
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
/* Workaround failure in MDIO access while cable is disconnected */
if ((hw->phy.type == e1000_phy_82577) &&
!(er32(STATUS) & E1000_STATUS_LU)) {
@@ -2508,10 +2652,6 @@ s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
goto out;
}
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- goto out;
-
hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
if (page == HV_INTC_FC_PAGE_START)
@@ -2529,42 +2669,76 @@ s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
ret_val = e1000e_write_phy_reg_mdic(hw,
IGP01E1000_PHY_PAGE_SELECT,
(page << IGP_PAGE_SHIFT));
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- goto out;
- }
hw->phy.addr = phy_addr;
}
}
ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
data);
- hw->phy.ops.release_phy(hw);
-
out:
/* Revert to MDIO fast mode, if applicable */
if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+ if (!locked)
+ hw->phy.ops.release_phy(hw);
+
return ret_val;
}
/**
- * e1000_write_phy_reg_hv - Write HV PHY register
+ * e1000_read_phy_reg_hv - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore then reads the PHY register at offset and stores
+ * the retrieved information in data. Release the acquired semaphore
+ * before exiting.
+ **/
+s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_phy_reg_hv(hw, offset, data, false);
+}
+
+/**
+ * e1000_read_phy_reg_hv_locked - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset and stores the retrieved information
+ * in data. Assumes semaphore already acquired.
+ **/
+s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_phy_reg_hv(hw, offset, data, true);
+}
+
+/**
+ * __e1000_write_phy_reg_hv - Write HV PHY register
* @hw: pointer to the HW structure
* @offset: register offset to write to
* @data: data to write at register offset
+ * @locked: semaphore has already been acquired or not
*
* Acquires semaphore, if necessary, then writes the data to PHY register
* at the offset. Release any acquired semaphores before exiting.
**/
-s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
+static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
+ bool locked)
{
s32 ret_val;
u16 page = BM_PHY_REG_PAGE(offset);
u16 reg = BM_PHY_REG_NUM(offset);
bool in_slow_mode = false;
+ if (!locked) {
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
/* Workaround failure in MDIO access while cable is disconnected */
if ((hw->phy.type == e1000_phy_82577) &&
!(er32(STATUS) & E1000_STATUS_LU)) {
@@ -2588,10 +2762,6 @@ s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
goto out;
}
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- goto out;
-
hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
if (page == HV_INTC_FC_PAGE_START)
@@ -2607,15 +2777,10 @@ s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
((MAX_PHY_REG_ADDRESS & reg) == 0) &&
(data & (1 << 11))) {
u16 data2 = 0x7EFF;
- hw->phy.ops.release_phy(hw);
ret_val = e1000_access_phy_debug_regs_hv(hw, (1 << 6) | 0x3,
&data2, false);
if (ret_val)
goto out;
-
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val)
- goto out;
}
if (reg > MAX_PHY_MULTI_PAGE_REG) {
@@ -2630,27 +2795,53 @@ s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
ret_val = e1000e_write_phy_reg_mdic(hw,
IGP01E1000_PHY_PAGE_SELECT,
(page << IGP_PAGE_SHIFT));
- if (ret_val) {
- hw->phy.ops.release_phy(hw);
- goto out;
- }
hw->phy.addr = phy_addr;
}
}
ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
data);
- hw->phy.ops.release_phy(hw);
out:
/* Revert to MDIO fast mode, if applicable */
if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+ if (!locked)
+ hw->phy.ops.release_phy(hw);
+
return ret_val;
}
/**
+ * e1000_write_phy_reg_hv - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore then writes the data to PHY register at the offset.
+ * Release the acquired semaphores before exiting.
+ **/
+s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_phy_reg_hv(hw, offset, data, false);
+}
+
+/**
+ * e1000_write_phy_reg_hv_locked - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes the data to PHY register at the offset. Assumes semaphore
+ * already acquired.
+ **/
+s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_phy_reg_hv(hw, offset, data, true);
+}
+
+/**
* e1000_get_phy_addr_for_hv_page - Get PHY adrress based on page
* @page: page to be accessed
**/
@@ -2671,10 +2862,9 @@ static u32 e1000_get_phy_addr_for_hv_page(u32 page)
* @data: pointer to the data to be read or written
* @read: determines if operation is read or written
*
- * Acquires semaphore, if necessary, then reads the PHY register at offset
- * and storing the retreived information in data. Release any acquired
- * semaphores before exiting. Note that the procedure to read these regs
- * uses the address port and data port to read/write.
+ * Reads the PHY register at offset and stores the retreived information
+ * in data. Assumes semaphore already acquired. Note that the procedure
+ * to read these regs uses the address port and data port to read/write.
**/
static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
u16 *data, bool read)
@@ -2682,20 +2872,12 @@ static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
s32 ret_val;
u32 addr_reg = 0;
u32 data_reg = 0;
- u8 phy_acquired = 1;
/* This takes care of the difference with desktop vs mobile phy */
addr_reg = (hw->phy.type == e1000_phy_82578) ?
I82578_ADDR_REG : I82577_ADDR_REG;
data_reg = addr_reg + 1;
- ret_val = hw->phy.ops.acquire_phy(hw);
- if (ret_val) {
- hw_dbg(hw, "Could not acquire PHY\n");
- phy_acquired = 0;
- goto out;
- }
-
/* All operations in this function are phy address 2 */
hw->phy.addr = 2;
@@ -2718,8 +2900,6 @@ static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
}
out:
- if (phy_acquired == 1)
- hw->phy.ops.release_phy(hw);
return ret_val;
}
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 04:30:30 +0000