1 files changed, 43 insertions, 13 deletions

diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 96e9565f1e08..a6f2063f1475 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -90,6 +90,9 @@ struct ftgmac100 {
 	struct mii_bus *mii_bus;
 	struct clk *clk;
 
+	/* AST2500/AST2600 RMII ref clock gate */
+	struct clk *rclk;
+
 	/* Link management */
 	int cur_speed;
 	int cur_duplex;
@@ -1609,7 +1612,7 @@ static int ftgmac100_setup_mdio(struct net_device *netdev)
 {
 	struct ftgmac100 *priv = netdev_priv(netdev);
 	struct platform_device *pdev = to_platform_device(priv->dev);
-	int phy_intf = PHY_INTERFACE_MODE_RGMII;
+	phy_interface_t phy_intf = PHY_INTERFACE_MODE_RGMII;
 	struct device_node *np = pdev->dev.of_node;
 	int i, err = 0;
 	u32 reg;
@@ -1634,8 +1637,8 @@ static int ftgmac100_setup_mdio(struct net_device *netdev)
 	/* Get PHY mode from device-tree */
 	if (np) {
 		/* Default to RGMII. It's a gigabit part after all */
-		phy_intf = of_get_phy_mode(np);
-		if (phy_intf < 0)
+		err = of_get_phy_mode(np, &phy_intf);
+		if (err)
 			phy_intf = PHY_INTERFACE_MODE_RGMII;
 
 		/* Aspeed only supports these. I don't know about other IP
@@ -1717,20 +1720,41 @@ static void ftgmac100_ncsi_handler(struct ncsi_dev *nd)
 		   nd->link_up ? "up" : "down");
 }
 
-static void ftgmac100_setup_clk(struct ftgmac100 *priv)
+static int ftgmac100_setup_clk(struct ftgmac100 *priv)
 {
-	priv->clk = devm_clk_get(priv->dev, NULL);
-	if (IS_ERR(priv->clk))
-		return;
+	struct clk *clk;
+	int rc;
 
-	clk_prepare_enable(priv->clk);
+	clk = devm_clk_get(priv->dev, NULL /* MACCLK */);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+	priv->clk = clk;
+	rc = clk_prepare_enable(priv->clk);
+	if (rc)
+		return rc;
 
 	/* Aspeed specifies a 100MHz clock is required for up to
 	 * 1000Mbit link speeds. As NCSI is limited to 100Mbit, 25MHz
 	 * is sufficient
 	 */
-	clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
-			FTGMAC_100MHZ);
+	rc = clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
+			  FTGMAC_100MHZ);
+	if (rc)
+		goto cleanup_clk;
+
+	/* RCLK is for RMII, typically used for NCSI. Optional because its not
+	 * necessary if it's the AST2400 MAC, or the MAC is configured for
+	 * RGMII, or the controller is not an ASPEED-based controller.
+	 */
+	priv->rclk = devm_clk_get_optional(priv->dev, "RCLK");
+	rc = clk_prepare_enable(priv->rclk);
+	if (!rc)
+		return 0;
+
+cleanup_clk:
+	clk_disable_unprepare(priv->clk);
+
+	return rc;
 }
 
 static int ftgmac100_probe(struct platform_device *pdev)
@@ -1852,8 +1876,11 @@ static int ftgmac100_probe(struct platform_device *pdev)
 			goto err_setup_mdio;
 	}
 
-	if (priv->is_aspeed)
-		ftgmac100_setup_clk(priv);
+	if (priv->is_aspeed) {
+		err = ftgmac100_setup_clk(priv);
+		if (err)
+			goto err_ncsi_dev;
+	}
 
 	/* Default ring sizes */
 	priv->rx_q_entries = priv->new_rx_q_entries = DEF_RX_QUEUE_ENTRIES;
@@ -1885,8 +1912,10 @@ static int ftgmac100_probe(struct platform_device *pdev)
 
 	return 0;
 
-err_ncsi_dev:
 err_register_netdev:
+	clk_disable_unprepare(priv->rclk);
+	clk_disable_unprepare(priv->clk);
+err_ncsi_dev:
 	ftgmac100_destroy_mdio(netdev);
 err_setup_mdio:
 	iounmap(priv->base);
@@ -1908,6 +1937,7 @@ static int ftgmac100_remove(struct platform_device *pdev)
 
 	unregister_netdev(netdev);
 
+	clk_disable_unprepare(priv->rclk);
 	clk_disable_unprepare(priv->clk);
 
 	/* There's a small chance the reset task will have been re-queued,