diff options
Diffstat (limited to 'drivers/net/ethernet/hp/hp100.h')
| -rw-r--r-- | drivers/net/ethernet/hp/hp100.h | 615 |
1 files changed, 615 insertions, 0 deletions
diff --git a/drivers/net/ethernet/hp/hp100.h b/drivers/net/ethernet/hp/hp100.h new file mode 100644 index 000000000000..b60e96fe38b4 --- /dev/null +++ b/drivers/net/ethernet/hp/hp100.h @@ -0,0 +1,615 @@ +/* + * hp100.h: Hewlett Packard HP10/100VG ANY LAN ethernet driver for Linux. + * + * $Id: hp100.h,v 1.51 1997/04/08 14:26:42 floeff Exp floeff $ + * + * Authors: Jaroslav Kysela, <perex@pf.jcu.cz> + * Siegfried Loeffler <floeff@tunix.mathematik.uni-stuttgart.de> + * + * This driver is based on the 'hpfepkt' crynwr packet driver. + * + * This source/code is public free; you can distribute it and/or modify + * it under terms of the GNU General Public License (published by the + * Free Software Foundation) either version two of this License, or any + * later version. + */ + +/**************************************************************************** + * Hardware Constants + ****************************************************************************/ + +/* + * Page Identifiers + * (Swap Paging Register, PAGING, bits 3:0, Offset 0x02) + */ + +#define HP100_PAGE_PERFORMANCE 0x0 /* Page 0 */ +#define HP100_PAGE_MAC_ADDRESS 0x1 /* Page 1 */ +#define HP100_PAGE_HW_MAP 0x2 /* Page 2 */ +#define HP100_PAGE_EEPROM_CTRL 0x3 /* Page 3 */ +#define HP100_PAGE_MAC_CTRL 0x4 /* Page 4 */ +#define HP100_PAGE_MMU_CFG 0x5 /* Page 5 */ +#define HP100_PAGE_ID_MAC_ADDR 0x6 /* Page 6 */ +#define HP100_PAGE_MMU_POINTER 0x7 /* Page 7 */ + + +/* Registers that are present on all pages */ + +#define HP100_REG_HW_ID 0x00 /* R: (16) Unique card ID */ +#define HP100_REG_TRACE 0x00 /* W: (16) Used for debug output */ +#define HP100_REG_PAGING 0x02 /* R: (16),15:4 Card ID */ + /* W: (16),3:0 Switch pages */ +#define HP100_REG_OPTION_LSW 0x04 /* RW: (16) Select card functions */ +#define HP100_REG_OPTION_MSW 0x06 /* RW: (16) Select card functions */ + +/* Page 0 - Performance */ + +#define HP100_REG_IRQ_STATUS 0x08 /* RW: (16) Which ints are pending */ +#define HP100_REG_IRQ_MASK 0x0a /* RW: (16) Select ints to allow */ +#define HP100_REG_FRAGMENT_LEN 0x0c /* W: (16)12:0 Current fragment len */ +/* Note: For 32 bit systems, fragment len and offset registers are available */ +/* at offset 0x28 and 0x2c, where they can be written as 32bit values. */ +#define HP100_REG_OFFSET 0x0e /* RW: (16)12:0 Offset to start read */ +#define HP100_REG_DATA32 0x10 /* RW: (32) I/O mode data port */ +#define HP100_REG_DATA16 0x12 /* RW: WORDs must be read from here */ +#define HP100_REG_TX_MEM_FREE 0x14 /* RD: (32) Amount of free Tx mem */ +#define HP100_REG_TX_PDA_L 0x14 /* W: (32) BM: Ptr to PDL, Low Pri */ +#define HP100_REG_TX_PDA_H 0x1c /* W: (32) BM: Ptr to PDL, High Pri */ +#define HP100_REG_RX_PKT_CNT 0x18 /* RD: (8) Rx count of pkts on card */ +#define HP100_REG_TX_PKT_CNT 0x19 /* RD: (8) Tx count of pkts on card */ +#define HP100_REG_RX_PDL 0x1a /* R: (8) BM: # rx pdl not executed */ +#define HP100_REG_TX_PDL 0x1b /* R: (8) BM: # tx pdl not executed */ +#define HP100_REG_RX_PDA 0x18 /* W: (32) BM: Up to 31 addresses */ + /* which point to a PDL */ +#define HP100_REG_SL_EARLY 0x1c /* (32) Enhanced Slave Early Rx */ +#define HP100_REG_STAT_DROPPED 0x20 /* R (12) Dropped Packet Counter */ +#define HP100_REG_STAT_ERRORED 0x22 /* R (8) Errored Packet Counter */ +#define HP100_REG_STAT_ABORT 0x23 /* R (8) Abort Counter/OW Coll. Flag */ +#define HP100_REG_RX_RING 0x24 /* W (32) Slave: RX Ring Pointers */ +#define HP100_REG_32_FRAGMENT_LEN 0x28 /* W (13) Slave: Fragment Length Reg */ +#define HP100_REG_32_OFFSET 0x2c /* W (16) Slave: Offset Register */ + +/* Page 1 - MAC Address/Hash Table */ + +#define HP100_REG_MAC_ADDR 0x08 /* RW: (8) Cards MAC address */ +#define HP100_REG_HASH_BYTE0 0x10 /* RW: (8) Cards multicast filter */ + +/* Page 2 - Hardware Mapping */ + +#define HP100_REG_MEM_MAP_LSW 0x08 /* RW: (16) LSW of cards mem addr */ +#define HP100_REG_MEM_MAP_MSW 0x0a /* RW: (16) MSW of cards mem addr */ +#define HP100_REG_IO_MAP 0x0c /* RW: (8) Cards I/O address */ +#define HP100_REG_IRQ_CHANNEL 0x0d /* RW: (8) IRQ and edge/level int */ +#define HP100_REG_SRAM 0x0e /* RW: (8) How much RAM on card */ +#define HP100_REG_BM 0x0f /* RW: (8) Controls BM functions */ + +/* New on Page 2 for ETR chips: */ +#define HP100_REG_MODECTRL1 0x10 /* RW: (8) Mode Control 1 */ +#define HP100_REG_MODECTRL2 0x11 /* RW: (8) Mode Control 2 */ +#define HP100_REG_PCICTRL1 0x12 /* RW: (8) PCI Cfg 1 */ +#define HP100_REG_PCICTRL2 0x13 /* RW: (8) PCI Cfg 2 */ +#define HP100_REG_PCIBUSMLAT 0x15 /* RW: (8) PCI Bus Master Latency */ +#define HP100_REG_EARLYTXCFG 0x16 /* RW: (16) Early TX Cfg/Cntrl Reg */ +#define HP100_REG_EARLYRXCFG 0x18 /* RW: (8) Early RX Cfg/Cntrl Reg */ +#define HP100_REG_ISAPNPCFG1 0x1a /* RW: (8) ISA PnP Cfg/Cntrl Reg 1 */ +#define HP100_REG_ISAPNPCFG2 0x1b /* RW: (8) ISA PnP Cfg/Cntrl Reg 2 */ + +/* Page 3 - EEPROM/Boot ROM */ + +#define HP100_REG_EEPROM_CTRL 0x08 /* RW: (16) Used to load EEPROM */ +#define HP100_REG_BOOTROM_CTRL 0x0a + +/* Page 4 - LAN Configuration (MAC_CTRL) */ + +#define HP100_REG_10_LAN_CFG_1 0x08 /* RW: (8) Set 10M XCVR functions */ +#define HP100_REG_10_LAN_CFG_2 0x09 /* RW: (8) 10M XCVR functions */ +#define HP100_REG_VG_LAN_CFG_1 0x0a /* RW: (8) Set 100M XCVR functions */ +#define HP100_REG_VG_LAN_CFG_2 0x0b /* RW: (8) 100M LAN Training cfgregs */ +#define HP100_REG_MAC_CFG_1 0x0c /* RW: (8) Types of pkts to accept */ +#define HP100_REG_MAC_CFG_2 0x0d /* RW: (8) Misc MAC functions */ +#define HP100_REG_MAC_CFG_3 0x0e /* RW: (8) Misc MAC functions */ +#define HP100_REG_MAC_CFG_4 0x0f /* R: (8) Misc MAC states */ +#define HP100_REG_DROPPED 0x10 /* R: (16),11:0 Pkts can't fit in mem */ +#define HP100_REG_CRC 0x12 /* R: (8) Pkts with CRC */ +#define HP100_REG_ABORT 0x13 /* R: (8) Aborted Tx pkts */ +#define HP100_REG_TRAIN_REQUEST 0x14 /* RW: (16) Endnode MAC register. */ +#define HP100_REG_TRAIN_ALLOW 0x16 /* R: (16) Hub allowed register */ + +/* Page 5 - MMU */ + +#define HP100_REG_RX_MEM_STOP 0x0c /* RW: (16) End of Rx ring addr */ +#define HP100_REG_TX_MEM_STOP 0x0e /* RW: (16) End of Tx ring addr */ +#define HP100_REG_PDL_MEM_STOP 0x10 /* Not used by 802.12 devices */ +#define HP100_REG_ECB_MEM_STOP 0x14 /* I've no idea what this is */ + +/* Page 6 - Card ID/Physical LAN Address */ + +#define HP100_REG_BOARD_ID 0x08 /* R: (8) EISA/ISA card ID */ +#define HP100_REG_BOARD_IO_CHCK 0x0c /* R: (8) Added to ID to get FFh */ +#define HP100_REG_SOFT_MODEL 0x0d /* R: (8) Config program defined */ +#define HP100_REG_LAN_ADDR 0x10 /* R: (8) MAC addr of card */ +#define HP100_REG_LAN_ADDR_CHCK 0x16 /* R: (8) Added to addr to get FFh */ + +/* Page 7 - MMU Current Pointers */ + +#define HP100_REG_PTR_RXSTART 0x08 /* R: (16) Current begin of Rx ring */ +#define HP100_REG_PTR_RXEND 0x0a /* R: (16) Current end of Rx ring */ +#define HP100_REG_PTR_TXSTART 0x0c /* R: (16) Current begin of Tx ring */ +#define HP100_REG_PTR_TXEND 0x0e /* R: (16) Current end of Rx ring */ +#define HP100_REG_PTR_RPDLSTART 0x10 +#define HP100_REG_PTR_RPDLEND 0x12 +#define HP100_REG_PTR_RINGPTRS 0x14 +#define HP100_REG_PTR_MEMDEBUG 0x1a +/* ------------------------------------------------------------------------ */ + + +/* + * Hardware ID Register I (Always available, HW_ID, Offset 0x00) + */ +#define HP100_HW_ID_CASCADE 0x4850 /* Identifies Cascade Chip */ + +/* + * Hardware ID Register 2 & Paging Register + * (Always available, PAGING, Offset 0x02) + * Bits 15:4 are for the Chip ID + */ +#define HP100_CHIPID_MASK 0xFFF0 +#define HP100_CHIPID_SHASTA 0x5350 /* Not 802.12 compliant */ + /* EISA BM/SL, MCA16/32 SL, ISA SL */ +#define HP100_CHIPID_RAINIER 0x5360 /* Not 802.12 compliant EISA BM, */ + /* PCI SL, MCA16/32 SL, ISA SL */ +#define HP100_CHIPID_LASSEN 0x5370 /* 802.12 compliant PCI BM, PCI SL */ + /* LRF supported */ + +/* + * Option Registers I and II + * (Always available, OPTION_LSW, Offset 0x04-0x05) + */ +#define HP100_DEBUG_EN 0x8000 /* 0:Dis., 1:Enable Debug Dump Ptr. */ +#define HP100_RX_HDR 0x4000 /* 0:Dis., 1:Enable putting pkt into */ + /* system mem. before Rx interrupt */ +#define HP100_MMAP_DIS 0x2000 /* 0:Enable, 1:Disable mem.mapping. */ + /* MMAP_DIS must be 0 and MEM_EN */ + /* must be 1 for memory-mapped */ + /* mode to be enabled */ +#define HP100_EE_EN 0x1000 /* 0:Disable,1:Enable EEPROM writing */ +#define HP100_BM_WRITE 0x0800 /* 0:Slave, 1:Bus Master for Tx data */ +#define HP100_BM_READ 0x0400 /* 0:Slave, 1:Bus Master for Rx data */ +#define HP100_TRI_INT 0x0200 /* 0:Don't, 1:Do tri-state the int */ +#define HP100_MEM_EN 0x0040 /* Config program set this to */ + /* 0:Disable, 1:Enable mem map. */ + /* See MMAP_DIS. */ +#define HP100_IO_EN 0x0020 /* 1:Enable I/O transfers */ +#define HP100_BOOT_EN 0x0010 /* 1:Enable boot ROM access */ +#define HP100_FAKE_INT 0x0008 /* 1:int */ +#define HP100_INT_EN 0x0004 /* 1:Enable ints from card */ +#define HP100_HW_RST 0x0002 /* 0:Reset, 1:Out of reset */ + /* NIC reset on 0 to 1 transition */ + +/* + * Option Register III + * (Always available, OPTION_MSW, Offset 0x06) + */ +#define HP100_PRIORITY_TX 0x0080 /* 1:Do all Tx pkts as priority */ +#define HP100_EE_LOAD 0x0040 /* 1:EEPROM loading, 0 when done */ +#define HP100_ADV_NXT_PKT 0x0004 /* 1:Advance to next pkt in Rx queue */ + /* h/w will set to 0 when done */ +#define HP100_TX_CMD 0x0002 /* 1:Tell h/w download done, h/w */ + /* will set to 0 when done */ + +/* + * Interrupt Status Registers I and II + * (Page PERFORMANCE, IRQ_STATUS, Offset 0x08-0x09) + * Note: With old chips, these Registers will clear when 1 is written to them + * with new chips this depends on setting of CLR_ISMODE + */ +#define HP100_RX_EARLY_INT 0x2000 +#define HP100_RX_PDA_ZERO 0x1000 +#define HP100_RX_PDL_FILL_COMPL 0x0800 +#define HP100_RX_PACKET 0x0400 /* 0:No, 1:Yes pkt has been Rx */ +#define HP100_RX_ERROR 0x0200 /* 0:No, 1:Yes Rx pkt had error */ +#define HP100_TX_PDA_ZERO 0x0020 /* 1 when PDA count goes to zero */ +#define HP100_TX_SPACE_AVAIL 0x0010 /* 0:<8192, 1:>=8192 Tx free bytes */ +#define HP100_TX_COMPLETE 0x0008 /* 0:No, 1:Yes a Tx has completed */ +#define HP100_MISC_ERROR 0x0004 /* 0:No, 1:Lan Link down or bus error */ +#define HP100_TX_ERROR 0x0002 /* 0:No, 1:Yes Tx pkt had error */ + +/* + * Xmit Memory Free Count + * (Page PERFORMANCE, TX_MEM_FREE, Offset 0x14) (Read only, 32bit) + */ +#define HP100_AUTO_COMPARE 0x80000000 /* Tx Space avail & pkts<255 */ +#define HP100_FREE_SPACE 0x7fffffe0 /* Tx free memory */ + +/* + * IRQ Channel + * (Page HW_MAP, IRQ_CHANNEL, Offset 0x0d) + */ +#define HP100_ZERO_WAIT_EN 0x80 /* 0:No, 1:Yes asserts NOWS signal */ +#define HP100_IRQ_SCRAMBLE 0x40 +#define HP100_BOND_HP 0x20 +#define HP100_LEVEL_IRQ 0x10 /* 0:Edge, 1:Level type interrupts. */ + /* (Only valid on EISA cards) */ +#define HP100_IRQMASK 0x0F /* Isolate the IRQ bits */ + +/* + * SRAM Parameters + * (Page HW_MAP, SRAM, Offset 0x0e) + */ +#define HP100_RAM_SIZE_MASK 0xe0 /* AND to get SRAM size index */ +#define HP100_RAM_SIZE_SHIFT 0x05 /* Shift count(put index in lwr bits) */ + +/* + * Bus Master Register + * (Page HW_MAP, BM, Offset 0x0f) + */ +#define HP100_BM_BURST_RD 0x01 /* EISA only: 1=Use burst trans. fm system */ + /* memory to chip (tx) */ +#define HP100_BM_BURST_WR 0x02 /* EISA only: 1=Use burst trans. fm system */ + /* memory to chip (rx) */ +#define HP100_BM_MASTER 0x04 /* 0:Slave, 1:BM mode */ +#define HP100_BM_PAGE_CK 0x08 /* This bit should be set whenever in */ + /* an EISA system */ +#define HP100_BM_PCI_8CLK 0x40 /* ... cycles 8 clocks apart */ + + +/* + * Mode Control Register I + * (Page HW_MAP, MODECTRL1, Offset0x10) + */ +#define HP100_TX_DUALQ 0x10 + /* If set and BM -> dual tx pda queues */ +#define HP100_ISR_CLRMODE 0x02 /* If set ISR will clear all pending */ + /* interrupts on read (etr only?) */ +#define HP100_EE_NOLOAD 0x04 /* Status whether res will be loaded */ + /* from the eeprom */ +#define HP100_TX_CNT_FLG 0x08 /* Controls Early TX Reg Cnt Field */ +#define HP100_PDL_USE3 0x10 /* If set BM engine will read only */ + /* first three data elements of a PDL */ + /* on the first access. */ +#define HP100_BUSTYPE_MASK 0xe0 /* Three bit bus type info */ + +/* + * Mode Control Register II + * (Page HW_MAP, MODECTRL2, Offset0x11) + */ +#define HP100_EE_MASK 0x0f /* Tell EEPROM circuit not to load */ + /* certain resources */ +#define HP100_DIS_CANCEL 0x20 /* For tx dualq mode operation */ +#define HP100_EN_PDL_WB 0x40 /* 1: Status of PDL completion may be */ + /* written back to system mem */ +#define HP100_EN_BUS_FAIL 0x80 /* Enables bus-fail portion of misc */ + /* interrupt */ + +/* + * PCI Configuration and Control Register I + * (Page HW_MAP, PCICTRL1, Offset 0x12) + */ +#define HP100_LO_MEM 0x01 /* 1: Mapped Mem requested below 1MB */ +#define HP100_NO_MEM 0x02 /* 1: Disables Req for sysmem to PCI */ + /* bios */ +#define HP100_USE_ISA 0x04 /* 1: isa type decodes will occur */ + /* simultaneously with PCI decodes */ +#define HP100_IRQ_HI_MASK 0xf0 /* pgmed by pci bios */ +#define HP100_PCI_IRQ_HI_MASK 0x78 /* Isolate 4 bits for PCI IRQ */ + +/* + * PCI Configuration and Control Register II + * (Page HW_MAP, PCICTRL2, Offset 0x13) + */ +#define HP100_RD_LINE_PDL 0x01 /* 1: PCI command Memory Read Line en */ +#define HP100_RD_TX_DATA_MASK 0x06 /* choose PCI memread cmds for TX */ +#define HP100_MWI 0x08 /* 1: en. PCI memory write invalidate */ +#define HP100_ARB_MODE 0x10 /* Select PCI arbitor type */ +#define HP100_STOP_EN 0x20 /* Enables PCI state machine to issue */ + /* pci stop if cascade not ready */ +#define HP100_IGNORE_PAR 0x40 /* 1: PCI state machine ignores parity */ +#define HP100_PCI_RESET 0x80 /* 0->1: Reset PCI block */ + +/* + * Early TX Configuration and Control Register + * (Page HW_MAP, EARLYTXCFG, Offset 0x16) + */ +#define HP100_EN_EARLY_TX 0x8000 /* 1=Enable Early TX */ +#define HP100_EN_ADAPTIVE 0x4000 /* 1=Enable adaptive mode */ +#define HP100_EN_TX_UR_IRQ 0x2000 /* reserved, must be 0 */ +#define HP100_EN_LOW_TX 0x1000 /* reserved, must be 0 */ +#define HP100_ET_CNT_MASK 0x0fff /* bits 11..0: ET counters */ + +/* + * Early RX Configuration and Control Register + * (Page HW_MAP, EARLYRXCFG, Offset 0x18) + */ +#define HP100_EN_EARLY_RX 0x80 /* 1=Enable Early RX */ +#define HP100_EN_LOW_RX 0x40 /* reserved, must be 0 */ +#define HP100_RX_TRIP_MASK 0x1f /* bits 4..0: threshold at which the + * early rx circuit will start the + * dma of received packet into system + * memory for BM */ + +/* + * Serial Devices Control Register + * (Page EEPROM_CTRL, EEPROM_CTRL, Offset 0x08) + */ +#define HP100_EEPROM_LOAD 0x0001 /* 0->1 loads EEPROM into registers. */ + /* When it goes back to 0, load is */ + /* complete. This should take ~600us. */ + +/* + * 10MB LAN Control and Configuration Register I + * (Page MAC_CTRL, 10_LAN_CFG_1, Offset 0x08) + */ +#define HP100_MAC10_SEL 0xc0 /* Get bits to indicate MAC */ +#define HP100_AUI_SEL 0x20 /* Status of AUI selection */ +#define HP100_LOW_TH 0x10 /* 0:No, 1:Yes allow better cabling */ +#define HP100_LINK_BEAT_DIS 0x08 /* 0:Enable, 1:Disable link beat */ +#define HP100_LINK_BEAT_ST 0x04 /* 0:No, 1:Yes link beat being Rx */ +#define HP100_R_ROL_ST 0x02 /* 0:No, 1:Yes Rx twisted pair has */ + /* been reversed */ +#define HP100_AUI_ST 0x01 /* 0:No, 1:Yes use AUI on TP card */ + +/* + * 10 MB LAN Control and Configuration Register II + * (Page MAC_CTRL, 10_LAN_CFG_2, Offset 0x09) + */ +#define HP100_SQU_ST 0x01 /* 0:No, 1:Yes collision signal sent */ + /* after Tx.Only used for AUI. */ +#define HP100_FULLDUP 0x02 /* 1: LXT901 XCVR fullduplx enabled */ +#define HP100_DOT3_MAC 0x04 /* 1: DOT 3 Mac sel. unless Autosel */ + +/* + * MAC Selection, use with MAC10_SEL bits + */ +#define HP100_AUTO_SEL_10 0x0 /* Auto select */ +#define HP100_XCVR_LXT901_10 0x1 /* LXT901 10BaseT transceiver */ +#define HP100_XCVR_7213 0x2 /* 7213 transceiver */ +#define HP100_XCVR_82503 0x3 /* 82503 transceiver */ + +/* + * 100MB LAN Training Register + * (Page MAC_CTRL, VG_LAN_CFG_2, Offset 0x0b) (old, pre 802.12) + */ +#define HP100_FRAME_FORMAT 0x08 /* 0:802.3, 1:802.5 frames */ +#define HP100_BRIDGE 0x04 /* 0:No, 1:Yes tell hub i am a bridge */ +#define HP100_PROM_MODE 0x02 /* 0:No, 1:Yes tell hub card is */ + /* promiscuous */ +#define HP100_REPEATER 0x01 /* 0:No, 1:Yes tell hub MAC wants to */ + /* be a cascaded repeater */ + +/* + * 100MB LAN Control and Configuration Register + * (Page MAC_CTRL, VG_LAN_CFG_1, Offset 0x0a) + */ +#define HP100_VG_SEL 0x80 /* 0:No, 1:Yes use 100 Mbit MAC */ +#define HP100_LINK_UP_ST 0x40 /* 0:No, 1:Yes endnode logged in */ +#define HP100_LINK_CABLE_ST 0x20 /* 0:No, 1:Yes cable can hear tones */ + /* from hub */ +#define HP100_LOAD_ADDR 0x10 /* 0->1 card addr will be sent */ + /* 100ms later the link status */ + /* bits are valid */ +#define HP100_LINK_CMD 0x08 /* 0->1 link will attempt to log in. */ + /* 100ms later the link status */ + /* bits are valid */ +#define HP100_TRN_DONE 0x04 /* NEW ETR-Chips only: Will be reset */ + /* after LinkUp Cmd is given and set */ + /* when training has completed. */ +#define HP100_LINK_GOOD_ST 0x02 /* 0:No, 1:Yes cable passed training */ +#define HP100_VG_RESET 0x01 /* 0:Yes, 1:No reset the 100VG MAC */ + + +/* + * MAC Configuration Register I + * (Page MAC_CTRL, MAC_CFG_1, Offset 0x0c) + */ +#define HP100_RX_IDLE 0x80 /* 0:Yes, 1:No currently receiving pkts */ +#define HP100_TX_IDLE 0x40 /* 0:Yes, 1:No currently Txing pkts */ +#define HP100_RX_EN 0x20 /* 1: allow receiving of pkts */ +#define HP100_TX_EN 0x10 /* 1: allow transmitting of pkts */ +#define HP100_ACC_ERRORED 0x08 /* 0:No, 1:Yes allow Rx of errored pkts */ +#define HP100_ACC_MC 0x04 /* 0:No, 1:Yes allow Rx of multicast pkts */ +#define HP100_ACC_BC 0x02 /* 0:No, 1:Yes allow Rx of broadcast pkts */ +#define HP100_ACC_PHY 0x01 /* 0:No, 1:Yes allow Rx of ALL phys. pkts */ +#define HP100_MAC1MODEMASK 0xf0 /* Hide ACC bits */ +#define HP100_MAC1MODE1 0x00 /* Receive nothing, must also disable RX */ +#define HP100_MAC1MODE2 0x00 +#define HP100_MAC1MODE3 HP100_MAC1MODE2 | HP100_ACC_BC +#define HP100_MAC1MODE4 HP100_MAC1MODE3 | HP100_ACC_MC +#define HP100_MAC1MODE5 HP100_MAC1MODE4 /* set mc hash to all ones also */ +#define HP100_MAC1MODE6 HP100_MAC1MODE5 | HP100_ACC_PHY /* Promiscuous */ +/* Note MODE6 will receive all GOOD packets on the LAN. This really needs + a mode 7 defined to be LAN Analyzer mode, which will receive errored and + runt packets, and keep the CRC bytes. */ +#define HP100_MAC1MODE7 HP100_MAC1MODE6 | HP100_ACC_ERRORED + +/* + * MAC Configuration Register II + * (Page MAC_CTRL, MAC_CFG_2, Offset 0x0d) + */ +#define HP100_TR_MODE 0x80 /* 0:No, 1:Yes support Token Ring formats */ +#define HP100_TX_SAME 0x40 /* 0:No, 1:Yes Tx same packet continuous */ +#define HP100_LBK_XCVR 0x20 /* 0:No, 1:Yes loopback through MAC & */ + /* transceiver */ +#define HP100_LBK_MAC 0x10 /* 0:No, 1:Yes loopback through MAC */ +#define HP100_CRC_I 0x08 /* 0:No, 1:Yes inhibit CRC on Tx packets */ +#define HP100_ACCNA 0x04 /* 1: For 802.5: Accept only token ring + * group addr that maches NA mask */ +#define HP100_KEEP_CRC 0x02 /* 0:No, 1:Yes keep CRC on Rx packets. */ + /* The length will reflect this. */ +#define HP100_ACCFA 0x01 /* 1: For 802.5: Accept only functional + * addrs that match FA mask (page1) */ +#define HP100_MAC2MODEMASK 0x02 +#define HP100_MAC2MODE1 0x00 +#define HP100_MAC2MODE2 0x00 +#define HP100_MAC2MODE3 0x00 +#define HP100_MAC2MODE4 0x00 +#define HP100_MAC2MODE5 0x00 +#define HP100_MAC2MODE6 0x00 +#define HP100_MAC2MODE7 KEEP_CRC + +/* + * MAC Configuration Register III + * (Page MAC_CTRL, MAC_CFG_3, Offset 0x0e) + */ +#define HP100_PACKET_PACE 0x03 /* Packet Pacing: + * 00: No packet pacing + * 01: 8 to 16 uS delay + * 10: 16 to 32 uS delay + * 11: 32 to 64 uS delay + */ +#define HP100_LRF_EN 0x04 /* 1: External LAN Rcv Filter and + * TCP/IP Checksumming enabled. */ +#define HP100_AUTO_MODE 0x10 /* 1: AutoSelect between 10/100 */ + +/* + * MAC Configuration Register IV + * (Page MAC_CTRL, MAC_CFG_4, Offset 0x0f) + */ +#define HP100_MAC_SEL_ST 0x01 /* (R): Status of external VGSEL + * Signal, 1=100VG, 0=10Mbit sel. */ +#define HP100_LINK_FAIL_ST 0x02 /* (R): Status of Link Fail portion + * of the Misc. Interrupt */ + +/* + * 100 MB LAN Training Request/Allowed Registers + * (Page MAC_CTRL, TRAIN_REQUEST and TRAIN_ALLOW, Offset 0x14-0x16)(ETR parts only) + */ +#define HP100_MACRQ_REPEATER 0x0001 /* 1: MAC tells HUB it wants to be + * a cascaded repeater + * 0: ... wants to be a DTE */ +#define HP100_MACRQ_PROMSC 0x0006 /* 2 bits: Promiscious mode + * 00: Rcv only unicast packets + * specifically addr to this + * endnode + * 10: Rcv all pckts fwded by + * the local repeater */ +#define HP100_MACRQ_FRAMEFMT_EITHER 0x0018 /* 11: either format allowed */ +#define HP100_MACRQ_FRAMEFMT_802_3 0x0000 /* 00: 802.3 is requested */ +#define HP100_MACRQ_FRAMEFMT_802_5 0x0010 /* 10: 802.5 format is requested */ +#define HP100_CARD_MACVER 0xe000 /* R: 3 bit Cards 100VG MAC version */ +#define HP100_MALLOW_REPEATER 0x0001 /* If reset, requested access as an + * end node is allowed */ +#define HP100_MALLOW_PROMSC 0x0004 /* 2 bits: Promiscious mode + * 00: Rcv only unicast packets + * specifically addr to this + * endnode + * 10: Rcv all pckts fwded by + * the local repeater */ +#define HP100_MALLOW_FRAMEFMT 0x00e0 /* 2 bits: Frame Format + * 00: 802.3 format will be used + * 10: 802.5 format will be used */ +#define HP100_MALLOW_ACCDENIED 0x0400 /* N bit */ +#define HP100_MALLOW_CONFIGURE 0x0f00 /* C bit */ +#define HP100_MALLOW_DUPADDR 0x1000 /* D bit */ +#define HP100_HUB_MACVER 0xe000 /* R: 3 bit 802.12 MAC/RMAC training */ + /* protocol of repeater */ + +/* ****************************************************************************** */ + +/* + * Set/Reset bits + */ +#define HP100_SET_HB 0x0100 /* 0:Set fields to 0 whose mask is 1 */ +#define HP100_SET_LB 0x0001 /* HB sets upper byte, LB sets lower byte */ +#define HP100_RESET_HB 0x0000 /* For readability when resetting bits */ +#define HP100_RESET_LB 0x0000 /* For readability when resetting bits */ + +/* + * Misc. Constants + */ +#define HP100_LAN_100 100 /* lan_type value for VG */ +#define HP100_LAN_10 10 /* lan_type value for 10BaseT */ +#define HP100_LAN_COAX 9 /* lan_type value for Coax */ +#define HP100_LAN_ERR (-1) /* lan_type value for link down */ + +/* + * Bus Master Data Structures ---------------------------------------------- + */ + +#define MAX_RX_PDL 30 /* Card limit = 31 */ +#define MAX_RX_FRAG 2 /* Don't need more... */ +#define MAX_TX_PDL 29 +#define MAX_TX_FRAG 2 /* Limit = 31 */ + +/* Define total PDL area size in bytes (should be 4096) */ +/* This is the size of kernel (dma) memory that will be allocated. */ +#define MAX_RINGSIZE ((MAX_RX_FRAG*8+4+4)*MAX_RX_PDL+(MAX_TX_FRAG*8+4+4)*MAX_TX_PDL)+16 + +/* Ethernet Packet Sizes */ +#define MIN_ETHER_SIZE 60 +#define MAX_ETHER_SIZE 1514 /* Needed for preallocation of */ + /* skb buffer when busmastering */ + +/* Tx or Rx Ring Entry */ +typedef struct hp100_ring { + u_int *pdl; /* Address of PDLs PDH, dword before + * this address is used for rx hdr */ + u_int pdl_paddr; /* Physical address of PDL */ + struct sk_buff *skb; + struct hp100_ring *next; +} hp100_ring_t; + + + +/* Mask for Header Descriptor */ +#define HP100_PKT_LEN_MASK 0x1FFF /* AND with RxLength to get length */ + + +/* Receive Packet Status. Note, the error bits are only valid if ACC_ERRORED + bit in the MAC Configuration Register 1 is set. */ +#define HP100_RX_PRI 0x8000 /* 0:No, 1:Yes packet is priority */ +#define HP100_SDF_ERR 0x4000 /* 0:No, 1:Yes start of frame error */ +#define HP100_SKEW_ERR 0x2000 /* 0:No, 1:Yes skew out of range */ +#define HP100_BAD_SYMBOL_ERR 0x1000 /* 0:No, 1:Yes invalid symbol received */ +#define HP100_RCV_IPM_ERR 0x0800 /* 0:No, 1:Yes pkt had an invalid packet */ + /* marker */ +#define HP100_SYMBOL_BAL_ERR 0x0400 /* 0:No, 1:Yes symbol balance error */ +#define HP100_VG_ALN_ERR 0x0200 /* 0:No, 1:Yes non-octet received */ +#define HP100_TRUNC_ERR 0x0100 /* 0:No, 1:Yes the packet was truncated */ +#define HP100_RUNT_ERR 0x0040 /* 0:No, 1:Yes pkt length < Min Pkt */ + /* Length Reg. */ +#define HP100_ALN_ERR 0x0010 /* 0:No, 1:Yes align error. */ +#define HP100_CRC_ERR 0x0008 /* 0:No, 1:Yes CRC occurred. */ + +/* The last three bits indicate the type of destination address */ + +#define HP100_MULTI_ADDR_HASH 0x0006 /* 110: Addr multicast, matched hash */ +#define HP100_BROADCAST_ADDR 0x0003 /* x11: Addr broadcast */ +#define HP100_MULTI_ADDR_NO_HASH 0x0002 /* 010: Addr multicast, didn't match hash */ +#define HP100_PHYS_ADDR_MATCH 0x0001 /* x01: Addr was physical and mine */ +#define HP100_PHYS_ADDR_NO_MATCH 0x0000 /* x00: Addr was physical but not mine */ + +/* + * macros + */ + +#define hp100_inb( reg ) \ + inb( ioaddr + HP100_REG_##reg ) +#define hp100_inw( reg ) \ + inw( ioaddr + HP100_REG_##reg ) +#define hp100_inl( reg ) \ + inl( ioaddr + HP100_REG_##reg ) +#define hp100_outb( data, reg ) \ + outb( data, ioaddr + HP100_REG_##reg ) +#define hp100_outw( data, reg ) \ + outw( data, ioaddr + HP100_REG_##reg ) +#define hp100_outl( data, reg ) \ + outl( data, ioaddr + HP100_REG_##reg ) +#define hp100_orb( data, reg ) \ + outb( inb( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg ) +#define hp100_orw( data, reg ) \ + outw( inw( ioaddr + HP100_REG_##reg ) | (data), ioaddr + HP100_REG_##reg ) +#define hp100_andb( data, reg ) \ + outb( inb( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg ) +#define hp100_andw( data, reg ) \ + outw( inw( ioaddr + HP100_REG_##reg ) & (data), ioaddr + HP100_REG_##reg ) + +#define hp100_page( page ) \ + outw( HP100_PAGE_##page, ioaddr + HP100_REG_PAGING ) +#define hp100_ints_off() \ + outw( HP100_INT_EN | HP100_RESET_LB, ioaddr + HP100_REG_OPTION_LSW ) +#define hp100_ints_on() \ + outw( HP100_INT_EN | HP100_SET_LB, ioaddr + HP100_REG_OPTION_LSW ) +#define hp100_mem_map_enable() \ + outw( HP100_MMAP_DIS | HP100_RESET_HB, ioaddr + HP100_REG_OPTION_LSW ) +#define hp100_mem_map_disable() \ + outw( HP100_MMAP_DIS | HP100_SET_HB, ioaddr + HP100_REG_OPTION_LSW ) |