summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/i825xx/eexpress.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/i825xx/eexpress.h')
-rw-r--r--drivers/net/ethernet/i825xx/eexpress.h179
1 files changed, 0 insertions, 179 deletions
diff --git a/drivers/net/ethernet/i825xx/eexpress.h b/drivers/net/ethernet/i825xx/eexpress.h
deleted file mode 100644
index dc9c6ea289e9..000000000000
--- a/drivers/net/ethernet/i825xx/eexpress.h
+++ /dev/null
@@ -1,179 +0,0 @@
-/*
- * eexpress.h: Intel EtherExpress16 defines
- */
-
-/*
- * EtherExpress card register addresses
- * as offsets from the base IO region (dev->base_addr)
- */
-
-#define DATAPORT 0x0000
-#define WRITE_PTR 0x0002
-#define READ_PTR 0x0004
-#define SIGNAL_CA 0x0006
-#define SET_IRQ 0x0007
-#define SM_PTR 0x0008
-#define MEM_Dec 0x000a
-#define MEM_Ctrl 0x000b
-#define MEM_Page_Ctrl 0x000c
-#define Config 0x000d
-#define EEPROM_Ctrl 0x000e
-#define ID_PORT 0x000f
-#define MEM_ECtrl 0x000f
-
-/*
- * card register defines
- */
-
-/* SET_IRQ */
-#define SIRQ_en 0x08
-#define SIRQ_dis 0x00
-
-/* EEPROM_Ctrl */
-#define EC_Clk 0x01
-#define EC_CS 0x02
-#define EC_Wr 0x04
-#define EC_Rd 0x08
-#define ASIC_RST 0x40
-#define i586_RST 0x80
-
-#define eeprom_delay() { udelay(40); }
-
-/*
- * i82586 Memory Configuration
- */
-
-/* (System Configuration Pointer) System start up block, read after 586_RST */
-#define SCP_START 0xfff6
-
-/* Intermediate System Configuration Pointer */
-#define ISCP_START 0x0000
-
-/* System Command Block */
-#define SCB_START 0x0008
-
-/* Start of buffer region. Everything before this is used for control
- * structures and the CU configuration program. The memory layout is
- * determined in eexp_hw_probe(), once we know how much memory is
- * available on the card.
- */
-
-#define TX_BUF_START 0x0100
-
-#define TX_BUF_SIZE ((24+ETH_FRAME_LEN+31)&~0x1f)
-#define RX_BUF_SIZE ((32+ETH_FRAME_LEN+31)&~0x1f)
-
-/*
- * SCB defines
- */
-
-/* these functions take the SCB status word and test the relevant status bit */
-#define SCB_complete(s) (((s) & 0x8000) != 0)
-#define SCB_rxdframe(s) (((s) & 0x4000) != 0)
-#define SCB_CUdead(s) (((s) & 0x2000) != 0)
-#define SCB_RUdead(s) (((s) & 0x1000) != 0)
-#define SCB_ack(s) ((s) & 0xf000)
-
-/* Command unit status: 0=idle, 1=suspended, 2=active */
-#define SCB_CUstat(s) (((s)&0x0300)>>8)
-
-/* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */
-#define SCB_RUstat(s) (((s)&0x0070)>>4)
-
-/* SCB commands */
-#define SCB_CUnop 0x0000
-#define SCB_CUstart 0x0100
-#define SCB_CUresume 0x0200
-#define SCB_CUsuspend 0x0300
-#define SCB_CUabort 0x0400
-#define SCB_resetchip 0x0080
-
-#define SCB_RUnop 0x0000
-#define SCB_RUstart 0x0010
-#define SCB_RUresume 0x0020
-#define SCB_RUsuspend 0x0030
-#define SCB_RUabort 0x0040
-
-/*
- * Command block defines
- */
-
-#define Stat_Done(s) (((s) & 0x8000) != 0)
-#define Stat_Busy(s) (((s) & 0x4000) != 0)
-#define Stat_OK(s) (((s) & 0x2000) != 0)
-#define Stat_Abort(s) (((s) & 0x1000) != 0)
-#define Stat_STFail (((s) & 0x0800) != 0)
-#define Stat_TNoCar(s) (((s) & 0x0400) != 0)
-#define Stat_TNoCTS(s) (((s) & 0x0200) != 0)
-#define Stat_TNoDMA(s) (((s) & 0x0100) != 0)
-#define Stat_TDefer(s) (((s) & 0x0080) != 0)
-#define Stat_TColl(s) (((s) & 0x0040) != 0)
-#define Stat_TXColl(s) (((s) & 0x0020) != 0)
-#define Stat_NoColl(s) ((s) & 0x000f)
-
-/* Cmd_END will end AFTER the command if this is the first
- * command block after an SCB_CUstart, but BEFORE the command
- * for all subsequent commands. Best strategy is to place
- * Cmd_INT on the last command in the sequence, followed by a
- * dummy Cmd_Nop with Cmd_END after this.
- */
-
-#define Cmd_END 0x8000
-#define Cmd_SUS 0x4000
-#define Cmd_INT 0x2000
-
-#define Cmd_Nop 0x0000
-#define Cmd_SetAddr 0x0001
-#define Cmd_Config 0x0002
-#define Cmd_MCast 0x0003
-#define Cmd_Xmit 0x0004
-#define Cmd_TDR 0x0005
-#define Cmd_Dump 0x0006
-#define Cmd_Diag 0x0007
-
-
-/*
- * Frame Descriptor (Receive block) defines
- */
-
-#define FD_Done(s) (((s) & 0x8000) != 0)
-#define FD_Busy(s) (((s) & 0x4000) != 0)
-#define FD_OK(s) (((s) & 0x2000) != 0)
-
-#define FD_CRC(s) (((s) & 0x0800) != 0)
-#define FD_Align(s) (((s) & 0x0400) != 0)
-#define FD_Resrc(s) (((s) & 0x0200) != 0)
-#define FD_DMA(s) (((s) & 0x0100) != 0)
-#define FD_Short(s) (((s) & 0x0080) != 0)
-#define FD_NoEOF(s) (((s) & 0x0040) != 0)
-
-struct rfd_header {
- volatile unsigned long flags;
- volatile unsigned short link;
- volatile unsigned short rbd_offset;
- volatile unsigned short dstaddr1;
- volatile unsigned short dstaddr2;
- volatile unsigned short dstaddr3;
- volatile unsigned short srcaddr1;
- volatile unsigned short srcaddr2;
- volatile unsigned short srcaddr3;
- volatile unsigned short length;
-
- /* This is actually a Receive Buffer Descriptor. The way we
- * arrange memory means that an RBD always follows the RFD that
- * points to it, so they might as well be in the same structure.
- */
- volatile unsigned short actual_count;
- volatile unsigned short next_rbd;
- volatile unsigned short buf_addr1;
- volatile unsigned short buf_addr2;
- volatile unsigned short size;
-};
-
-/* Returned data from the Time Domain Reflectometer */
-
-#define TDR_LINKOK (1<<15)
-#define TDR_XCVRPROBLEM (1<<14)
-#define TDR_OPEN (1<<13)
-#define TDR_SHORT (1<<12)
-#define TDR_TIME 0x7ff