diff options
Diffstat (limited to 'drivers/net/sk98lin')
40 files changed, 0 insertions, 41302 deletions
diff --git a/drivers/net/sk98lin/Makefile b/drivers/net/sk98lin/Makefile deleted file mode 100644 index afd900d5d730..000000000000 --- a/drivers/net/sk98lin/Makefile +++ /dev/null @@ -1,87 +0,0 @@ -# -# Makefile for the SysKonnect SK-98xx device driver. -# - - -# -# Standalone driver params -# SKPARAM += -DSK_KERNEL_24 -# SKPARAM += -DSK_KERNEL_24_26 -# SKPARAM += -DSK_KERNEL_26 -# SKPARAM += -DSK_KERNEL_22_24 - -obj-$(CONFIG_SK98LIN) += sk98lin.o -sk98lin-objs := \ - skge.o \ - skethtool.o \ - skdim.o \ - skaddr.o \ - skgehwt.o \ - skgeinit.o \ - skgepnmi.o \ - skgesirq.o \ - ski2c.o \ - sklm80.o \ - skqueue.o \ - skrlmt.o \ - sktimer.o \ - skvpd.o \ - skxmac2.o - -# DBGDEF = \ -# -DDEBUG - -ifdef DEBUG -DBGDEF += \ --DSK_DEBUG_CHKMOD=0x00000000L \ --DSK_DEBUG_CHKCAT=0x00000000L -endif - - -# **** possible debug modules for SK_DEBUG_CHKMOD ***************** -# SK_DBGMOD_MERR 0x00000001L /* general module error indication */ -# SK_DBGMOD_HWM 0x00000002L /* Hardware init module */ -# SK_DBGMOD_RLMT 0x00000004L /* RLMT module */ -# SK_DBGMOD_VPD 0x00000008L /* VPD module */ -# SK_DBGMOD_I2C 0x00000010L /* I2C module */ -# SK_DBGMOD_PNMI 0x00000020L /* PNMI module */ -# SK_DBGMOD_CSUM 0x00000040L /* CSUM module */ -# SK_DBGMOD_ADDR 0x00000080L /* ADDR module */ -# SK_DBGMOD_DRV 0x00010000L /* DRV module */ - -# **** possible debug categories for SK_DEBUG_CHKCAT ************** -# *** common modules *** -# SK_DBGCAT_INIT 0x00000001L module/driver initialization -# SK_DBGCAT_CTRL 0x00000002L controlling: add/rmv MCA/MAC and other controls (IOCTL) -# SK_DBGCAT_ERR 0x00000004L error handling paths -# SK_DBGCAT_TX 0x00000008L transmit path -# SK_DBGCAT_RX 0x00000010L receive path -# SK_DBGCAT_IRQ 0x00000020L general IRQ handling -# SK_DBGCAT_QUEUE 0x00000040L any queue management -# SK_DBGCAT_DUMP 0x00000080L large data output e.g. hex dump -# SK_DBGCAT_FATAL 0x00000100L large data output e.g. hex dump - -# *** driver (file skge.c) *** -# SK_DBGCAT_DRV_ENTRY 0x00010000 entry points -# SK_DBGCAT_DRV_??? 0x00020000 not used -# SK_DBGCAT_DRV_MCA 0x00040000 multicast -# SK_DBGCAT_DRV_TX_PROGRESS 0x00080000 tx path -# SK_DBGCAT_DRV_RX_PROGRESS 0x00100000 rx path -# SK_DBGCAT_DRV_PROGRESS 0x00200000 general runtime -# SK_DBGCAT_DRV_??? 0x00400000 not used -# SK_DBGCAT_DRV_PROM 0x00800000 promiscuous mode -# SK_DBGCAT_DRV_TX_FRAME 0x01000000 display tx frames -# SK_DBGCAT_DRV_ERROR 0x02000000 error conditions -# SK_DBGCAT_DRV_INT_SRC 0x04000000 interrupts sources -# SK_DBGCAT_DRV_EVENT 0x08000000 driver events - -EXTRA_CFLAGS += -Idrivers/net/sk98lin -DSK_DIAG_SUPPORT -DGENESIS -DYUKON $(DBGDEF) $(SKPARAM) - -clean: - rm -f core *.o *.a *.s - - - - - - diff --git a/drivers/net/sk98lin/h/lm80.h b/drivers/net/sk98lin/h/lm80.h deleted file mode 100644 index 4e2dbbf78000..000000000000 --- a/drivers/net/sk98lin/h/lm80.h +++ /dev/null @@ -1,179 +0,0 @@ -/****************************************************************************** - * - * Name: lm80.h - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.6 $ - * Date: $Date: 2003/05/13 17:26:52 $ - * Purpose: Contains all defines for the LM80 Chip - * (National Semiconductor). - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef __INC_LM80_H -#define __INC_LM80_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/* defines ********************************************************************/ - -/* - * LM80 register definition - * - * All registers are 8 bit wide - */ -#define LM80_CFG 0x00 /* Configuration Register */ -#define LM80_ISRC_1 0x01 /* Interrupt Status Register 1 */ -#define LM80_ISRC_2 0x02 /* Interrupt Status Register 2 */ -#define LM80_IMSK_1 0x03 /* Interrupt Mask Register 1 */ -#define LM80_IMSK_2 0x04 /* Interrupt Mask Register 2 */ -#define LM80_FAN_CTRL 0x05 /* Fan Devisor/RST#/OS# Register */ -#define LM80_TEMP_CTRL 0x06 /* OS# Config, Temp Res. Reg */ - /* 0x07 - 0x1f reserved */ - /* current values */ -#define LM80_VT0_IN 0x20 /* current Voltage 0 value */ -#define LM80_VT1_IN 0x21 /* current Voltage 1 value */ -#define LM80_VT2_IN 0x22 /* current Voltage 2 value */ -#define LM80_VT3_IN 0x23 /* current Voltage 3 value */ -#define LM80_VT4_IN 0x24 /* current Voltage 4 value */ -#define LM80_VT5_IN 0x25 /* current Voltage 5 value */ -#define LM80_VT6_IN 0x26 /* current Voltage 6 value */ -#define LM80_TEMP_IN 0x27 /* current Temperature value */ -#define LM80_FAN1_IN 0x28 /* current Fan 1 count */ -#define LM80_FAN2_IN 0x29 /* current Fan 2 count */ - /* limit values */ -#define LM80_VT0_HIGH_LIM 0x2a /* high limit val for Voltage 0 */ -#define LM80_VT0_LOW_LIM 0x2b /* low limit val for Voltage 0 */ -#define LM80_VT1_HIGH_LIM 0x2c /* high limit val for Voltage 1 */ -#define LM80_VT1_LOW_LIM 0x2d /* low limit val for Voltage 1 */ -#define LM80_VT2_HIGH_LIM 0x2e /* high limit val for Voltage 2 */ -#define LM80_VT2_LOW_LIM 0x2f /* low limit val for Voltage 2 */ -#define LM80_VT3_HIGH_LIM 0x30 /* high limit val for Voltage 3 */ -#define LM80_VT3_LOW_LIM 0x31 /* low limit val for Voltage 3 */ -#define LM80_VT4_HIGH_LIM 0x32 /* high limit val for Voltage 4 */ -#define LM80_VT4_LOW_LIM 0x33 /* low limit val for Voltage 4 */ -#define LM80_VT5_HIGH_LIM 0x34 /* high limit val for Voltage 5 */ -#define LM80_VT5_LOW_LIM 0x35 /* low limit val for Voltage 5 */ -#define LM80_VT6_HIGH_LIM 0x36 /* high limit val for Voltage 6 */ -#define LM80_VT6_LOW_LIM 0x37 /* low limit val for Voltage 6 */ -#define LM80_THOT_LIM_UP 0x38 /* hot temperature limit (high) */ -#define LM80_THOT_LIM_LO 0x39 /* hot temperature limit (low) */ -#define LM80_TOS_LIM_UP 0x3a /* OS temperature limit (high) */ -#define LM80_TOS_LIM_LO 0x3b /* OS temperature limit (low) */ -#define LM80_FAN1_COUNT_LIM 0x3c /* Fan 1 count limit (high) */ -#define LM80_FAN2_COUNT_LIM 0x3d /* Fan 2 count limit (low) */ - /* 0x3e - 0x3f reserved */ - -/* - * LM80 bit definitions - */ - -/* LM80_CFG Configuration Register */ -#define LM80_CFG_START (1<<0) /* start monitoring operation */ -#define LM80_CFG_INT_ENA (1<<1) /* enables the INT# Interrupt output */ -#define LM80_CFG_INT_POL (1<<2) /* INT# pol: 0 act low, 1 act high */ -#define LM80_CFG_INT_CLR (1<<3) /* disables INT#/RST_OUT#/OS# outputs */ -#define LM80_CFG_RESET (1<<4) /* signals a reset */ -#define LM80_CFG_CHASS_CLR (1<<5) /* clears Chassis Intrusion (CI) pin */ -#define LM80_CFG_GPO (1<<6) /* drives the GPO# pin */ -#define LM80_CFG_INIT (1<<7) /* restore power on defaults */ - -/* LM80_ISRC_1 Interrupt Status Register 1 */ -/* LM80_IMSK_1 Interrupt Mask Register 1 */ -#define LM80_IS_VT0 (1<<0) /* limit exceeded for Voltage 0 */ -#define LM80_IS_VT1 (1<<1) /* limit exceeded for Voltage 1 */ -#define LM80_IS_VT2 (1<<2) /* limit exceeded for Voltage 2 */ -#define LM80_IS_VT3 (1<<3) /* limit exceeded for Voltage 3 */ -#define LM80_IS_VT4 (1<<4) /* limit exceeded for Voltage 4 */ -#define LM80_IS_VT5 (1<<5) /* limit exceeded for Voltage 5 */ -#define LM80_IS_VT6 (1<<6) /* limit exceeded for Voltage 6 */ -#define LM80_IS_INT_IN (1<<7) /* state of INT_IN# */ - -/* LM80_ISRC_2 Interrupt Status Register 2 */ -/* LM80_IMSK_2 Interrupt Mask Register 2 */ -#define LM80_IS_TEMP (1<<0) /* HOT temperature limit exceeded */ -#define LM80_IS_BTI (1<<1) /* state of BTI# pin */ -#define LM80_IS_FAN1 (1<<2) /* count limit exceeded for Fan 1 */ -#define LM80_IS_FAN2 (1<<3) /* count limit exceeded for Fan 2 */ -#define LM80_IS_CI (1<<4) /* Chassis Intrusion occured */ -#define LM80_IS_OS (1<<5) /* OS temperature limit exceeded */ - /* bit 6 and 7 are reserved in LM80_ISRC_2 */ -#define LM80_IS_HT_IRQ_MD (1<<6) /* Hot temperature interrupt mode */ -#define LM80_IS_OT_IRQ_MD (1<<7) /* OS temperature interrupt mode */ - -/* LM80_FAN_CTRL Fan Devisor/RST#/OS# Register */ -#define LM80_FAN1_MD_SEL (1<<0) /* Fan 1 mode select */ -#define LM80_FAN2_MD_SEL (1<<1) /* Fan 2 mode select */ -#define LM80_FAN1_PRM_CTL (3<<2) /* Fan 1 speed control */ -#define LM80_FAN2_PRM_CTL (3<<4) /* Fan 2 speed control */ -#define LM80_FAN_OS_ENA (1<<6) /* enable OS mode on RST_OUT#/OS# pins*/ -#define LM80_FAN_RST_ENA (1<<7) /* sets RST_OUT#/OS# pins in RST mode */ - -/* LM80_TEMP_CTRL OS# Config, Temp Res. Reg */ -#define LM80_TEMP_OS_STAT (1<<0) /* mirrors the state of RST_OUT#/OS# */ -#define LM80_TEMP_OS_POL (1<<1) /* select OS# polarity */ -#define LM80_TEMP_OS_MODE (1<<2) /* selects Interrupt mode */ -#define LM80_TEMP_RES (1<<3) /* selects 9 or 11 bit temp resulution*/ -#define LM80_TEMP_LSB (0xf<<4)/* 4 LSBs of 11 bit temp data */ -#define LM80_TEMP_LSB_9 (1<<7) /* LSB of 9 bit temperature data */ - - /* 0x07 - 0x1f reserved */ -/* LM80_VT0_IN current Voltage 0 value */ -/* LM80_VT1_IN current Voltage 1 value */ -/* LM80_VT2_IN current Voltage 2 value */ -/* LM80_VT3_IN current Voltage 3 value */ -/* LM80_VT4_IN current Voltage 4 value */ -/* LM80_VT5_IN current Voltage 5 value */ -/* LM80_VT6_IN current Voltage 6 value */ -/* LM80_TEMP_IN current temperature value */ -/* LM80_FAN1_IN current Fan 1 count */ -/* LM80_FAN2_IN current Fan 2 count */ -/* LM80_VT0_HIGH_LIM high limit val for Voltage 0 */ -/* LM80_VT0_LOW_LIM low limit val for Voltage 0 */ -/* LM80_VT1_HIGH_LIM high limit val for Voltage 1 */ -/* LM80_VT1_LOW_LIM low limit val for Voltage 1 */ -/* LM80_VT2_HIGH_LIM high limit val for Voltage 2 */ -/* LM80_VT2_LOW_LIM low limit val for Voltage 2 */ -/* LM80_VT3_HIGH_LIM high limit val for Voltage 3 */ -/* LM80_VT3_LOW_LIM low limit val for Voltage 3 */ -/* LM80_VT4_HIGH_LIM high limit val for Voltage 4 */ -/* LM80_VT4_LOW_LIM low limit val for Voltage 4 */ -/* LM80_VT5_HIGH_LIM high limit val for Voltage 5 */ -/* LM80_VT5_LOW_LIM low limit val for Voltage 5 */ -/* LM80_VT6_HIGH_LIM high limit val for Voltage 6 */ -/* LM80_VT6_LOW_LIM low limit val for Voltage 6 */ -/* LM80_THOT_LIM_UP hot temperature limit (high) */ -/* LM80_THOT_LIM_LO hot temperature limit (low) */ -/* LM80_TOS_LIM_UP OS temperature limit (high) */ -/* LM80_TOS_LIM_LO OS temperature limit (low) */ -/* LM80_FAN1_COUNT_LIM Fan 1 count limit (high) */ -/* LM80_FAN2_COUNT_LIM Fan 2 count limit (low) */ - /* 0x3e - 0x3f reserved */ - -#define LM80_ADDR 0x28 /* LM80 default addr */ - -/* typedefs *******************************************************************/ - - -/* function prototypes ********************************************************/ - -#ifdef __cplusplus -} -#endif /* __cplusplus */ - -#endif /* __INC_LM80_H */ diff --git a/drivers/net/sk98lin/h/skaddr.h b/drivers/net/sk98lin/h/skaddr.h deleted file mode 100644 index 423ad063d09b..000000000000 --- a/drivers/net/sk98lin/h/skaddr.h +++ /dev/null @@ -1,285 +0,0 @@ -/****************************************************************************** - * - * Name: skaddr.h - * Project: Gigabit Ethernet Adapters, ADDR-Modul - * Version: $Revision: 1.29 $ - * Date: $Date: 2003/05/13 16:57:24 $ - * Purpose: Header file for Address Management (MC, UC, Prom). - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * This module is intended to manage multicast addresses and promiscuous mode - * on GEnesis adapters. - * - * Include File Hierarchy: - * - * "skdrv1st.h" - * ... - * "sktypes.h" - * "skqueue.h" - * "skaddr.h" - * ... - * "skdrv2nd.h" - * - ******************************************************************************/ - -#ifndef __INC_SKADDR_H -#define __INC_SKADDR_H - -#ifdef __cplusplus -extern "C" { -#endif /* cplusplus */ - -/* defines ********************************************************************/ - -#define SK_MAC_ADDR_LEN 6 /* Length of MAC address. */ -#define SK_MAX_ADDRS 14 /* #Addrs for exact match. */ - -/* ----- Common return values ----- */ - -#define SK_ADDR_SUCCESS 0 /* Function returned successfully. */ -#define SK_ADDR_ILLEGAL_PORT 100 /* Port number too high. */ -#define SK_ADDR_TOO_EARLY 101 /* Function called too early. */ - -/* ----- Clear/Add flag bits ----- */ - -#define SK_ADDR_PERMANENT 1 /* RLMT Address */ - -/* ----- Additional Clear flag bits ----- */ - -#define SK_MC_SW_ONLY 2 /* Do not update HW when clearing. */ - -/* ----- Override flag bits ----- */ - -#define SK_ADDR_LOGICAL_ADDRESS 0 -#define SK_ADDR_VIRTUAL_ADDRESS (SK_ADDR_LOGICAL_ADDRESS) /* old */ -#define SK_ADDR_PHYSICAL_ADDRESS 1 -#define SK_ADDR_CLEAR_LOGICAL 2 -#define SK_ADDR_SET_LOGICAL 4 - -/* ----- Override return values ----- */ - -#define SK_ADDR_OVERRIDE_SUCCESS (SK_ADDR_SUCCESS) -#define SK_ADDR_DUPLICATE_ADDRESS 1 -#define SK_ADDR_MULTICAST_ADDRESS 2 - -/* ----- Partitioning of excact match table ----- */ - -#define SK_ADDR_EXACT_MATCHES 16 /* #Exact match entries. */ - -#define SK_ADDR_FIRST_MATCH_RLMT 1 -#define SK_ADDR_LAST_MATCH_RLMT 2 -#define SK_ADDR_FIRST_MATCH_DRV 3 -#define SK_ADDR_LAST_MATCH_DRV (SK_ADDR_EXACT_MATCHES - 1) - -/* ----- SkAddrMcAdd/SkAddrMcUpdate return values ----- */ - -#define SK_MC_FILTERING_EXACT 0 /* Exact filtering. */ -#define SK_MC_FILTERING_INEXACT 1 /* Inexact filtering. */ - -/* ----- Additional SkAddrMcAdd return values ----- */ - -#define SK_MC_ILLEGAL_ADDRESS 2 /* Illegal address. */ -#define SK_MC_ILLEGAL_PORT 3 /* Illegal port (not the active one). */ -#define SK_MC_RLMT_OVERFLOW 4 /* Too many RLMT mc addresses. */ - -/* Promiscuous mode bits ----- */ - -#define SK_PROM_MODE_NONE 0 /* Normal receive. */ -#define SK_PROM_MODE_LLC 1 /* Receive all LLC frames. */ -#define SK_PROM_MODE_ALL_MC 2 /* Receive all multicast frames. */ -/* #define SK_PROM_MODE_NON_LLC 4 */ /* Receive all non-LLC frames. */ - -/* Macros */ - -#ifdef OLD_STUFF -#ifndef SK_ADDR_EQUAL -/* - * "&" instead of "&&" allows better optimization on IA-64. - * The replacement is safe here, as all bytes exist. - */ -#ifndef SK_ADDR_DWORD_COMPARE -#define SK_ADDR_EQUAL(A1,A2) ( \ - (((SK_U8 *)(A1))[5] == ((SK_U8 *)(A2))[5]) & \ - (((SK_U8 *)(A1))[4] == ((SK_U8 *)(A2))[4]) & \ - (((SK_U8 *)(A1))[3] == ((SK_U8 *)(A2))[3]) & \ - (((SK_U8 *)(A1))[2] == ((SK_U8 *)(A2))[2]) & \ - (((SK_U8 *)(A1))[1] == ((SK_U8 *)(A2))[1]) & \ - (((SK_U8 *)(A1))[0] == ((SK_U8 *)(A2))[0])) -#else /* SK_ADDR_DWORD_COMPARE */ -#define SK_ADDR_EQUAL(A1,A2) ( \ - (*(SK_U32 *)&(((SK_U8 *)(A1))[2]) == *(SK_U32 *)&(((SK_U8 *)(A2))[2])) & \ - (*(SK_U32 *)&(((SK_U8 *)(A1))[0]) == *(SK_U32 *)&(((SK_U8 *)(A2))[0]))) -#endif /* SK_ADDR_DWORD_COMPARE */ -#endif /* SK_ADDR_EQUAL */ -#endif /* 0 */ - -#ifndef SK_ADDR_EQUAL -#ifndef SK_ADDR_DWORD_COMPARE -#define SK_ADDR_EQUAL(A1,A2) ( \ - (((SK_U8 SK_FAR *)(A1))[5] == ((SK_U8 SK_FAR *)(A2))[5]) & \ - (((SK_U8 SK_FAR *)(A1))[4] == ((SK_U8 SK_FAR *)(A2))[4]) & \ - (((SK_U8 SK_FAR *)(A1))[3] == ((SK_U8 SK_FAR *)(A2))[3]) & \ - (((SK_U8 SK_FAR *)(A1))[2] == ((SK_U8 SK_FAR *)(A2))[2]) & \ - (((SK_U8 SK_FAR *)(A1))[1] == ((SK_U8 SK_FAR *)(A2))[1]) & \ - (((SK_U8 SK_FAR *)(A1))[0] == ((SK_U8 SK_FAR *)(A2))[0])) -#else /* SK_ADDR_DWORD_COMPARE */ -#define SK_ADDR_EQUAL(A1,A2) ( \ - (*(SK_U16 SK_FAR *)&(((SK_U8 SK_FAR *)(A1))[4]) == \ - *(SK_U16 SK_FAR *)&(((SK_U8 SK_FAR *)(A2))[4])) && \ - (*(SK_U32 SK_FAR *)&(((SK_U8 SK_FAR *)(A1))[0]) == \ - *(SK_U32 SK_FAR *)&(((SK_U8 SK_FAR *)(A2))[0]))) -#endif /* SK_ADDR_DWORD_COMPARE */ -#endif /* SK_ADDR_EQUAL */ - -/* typedefs *******************************************************************/ - -typedef struct s_MacAddr { - SK_U8 a[SK_MAC_ADDR_LEN]; -} SK_MAC_ADDR; - - -/* SK_FILTER is used to ensure alignment of the filter. */ -typedef union s_InexactFilter { - SK_U8 Bytes[8]; - SK_U64 Val; /* Dummy entry for alignment only. */ -} SK_FILTER64; - - -typedef struct s_AddrNet SK_ADDR_NET; - - -typedef struct s_AddrPort { - -/* ----- Public part (read-only) ----- */ - - SK_MAC_ADDR CurrentMacAddress; /* Current physical MAC Address. */ - SK_MAC_ADDR PermanentMacAddress; /* Permanent physical MAC Address. */ - int PromMode; /* Promiscuous Mode. */ - -/* ----- Private part ----- */ - - SK_MAC_ADDR PreviousMacAddress; /* Prev. phys. MAC Address. */ - SK_BOOL CurrentMacAddressSet; /* CurrentMacAddress is set. */ - SK_U8 Align01; - - SK_U32 FirstExactMatchRlmt; - SK_U32 NextExactMatchRlmt; - SK_U32 FirstExactMatchDrv; - SK_U32 NextExactMatchDrv; - SK_MAC_ADDR Exact[SK_ADDR_EXACT_MATCHES]; - SK_FILTER64 InexactFilter; /* For 64-bit hash register. */ - SK_FILTER64 InexactRlmtFilter; /* For 64-bit hash register. */ - SK_FILTER64 InexactDrvFilter; /* For 64-bit hash register. */ -} SK_ADDR_PORT; - - -struct s_AddrNet { -/* ----- Public part (read-only) ----- */ - - SK_MAC_ADDR CurrentMacAddress; /* Logical MAC Address. */ - SK_MAC_ADDR PermanentMacAddress; /* Logical MAC Address. */ - -/* ----- Private part ----- */ - - SK_U32 ActivePort; /* View of module ADDR. */ - SK_BOOL CurrentMacAddressSet; /* CurrentMacAddress is set. */ - SK_U8 Align01; - SK_U16 Align02; -}; - - -typedef struct s_Addr { - -/* ----- Public part (read-only) ----- */ - - SK_ADDR_NET Net[SK_MAX_NETS]; - SK_ADDR_PORT Port[SK_MAX_MACS]; - -/* ----- Private part ----- */ -} SK_ADDR; - -/* function prototypes ********************************************************/ - -#ifndef SK_KR_PROTO - -/* Functions provided by SkAddr */ - -/* ANSI/C++ compliant function prototypes */ - -extern int SkAddrInit( - SK_AC *pAC, - SK_IOC IoC, - int Level); - -extern int SkAddrMcClear( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 PortNumber, - int Flags); - -extern int SkAddrMcAdd( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 PortNumber, - SK_MAC_ADDR *pMc, - int Flags); - -extern int SkAddrMcUpdate( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 PortNumber); - -extern int SkAddrOverride( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 PortNumber, - SK_MAC_ADDR SK_FAR *pNewAddr, - int Flags); - -extern int SkAddrPromiscuousChange( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 PortNumber, - int NewPromMode); - -#ifndef SK_SLIM -extern int SkAddrSwap( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 FromPortNumber, - SK_U32 ToPortNumber); -#endif - -#else /* defined(SK_KR_PROTO)) */ - -/* Non-ANSI/C++ compliant function prototypes */ - -#error KR-style prototypes are not yet provided. - -#endif /* defined(SK_KR_PROTO)) */ - - -#ifdef __cplusplus -} -#endif /* __cplusplus */ - -#endif /* __INC_SKADDR_H */ diff --git a/drivers/net/sk98lin/h/skcsum.h b/drivers/net/sk98lin/h/skcsum.h deleted file mode 100644 index 6e256bd9a28c..000000000000 --- a/drivers/net/sk98lin/h/skcsum.h +++ /dev/null @@ -1,213 +0,0 @@ -/****************************************************************************** - * - * Name: skcsum.h - * Project: GEnesis - SysKonnect SK-NET Gigabit Ethernet (SK-98xx) - * Version: $Revision: 1.10 $ - * Date: $Date: 2003/08/20 13:59:57 $ - * Purpose: Store/verify Internet checksum in send/receive packets. - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2001 SysKonnect GmbH. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * Public header file for the "GEnesis" common module "CSUM". - * - * "GEnesis" is an abbreviation of "Gigabit Ethernet Network System in Silicon" - * and is the code name of this SysKonnect project. - * - * Compilation Options: - * - * SK_USE_CSUM - Define if CSUM is to be used. Otherwise, CSUM will be an - * empty module. - * - * SKCS_OVERWRITE_PROTO - Define to overwrite the default protocol id - * definitions. In this case, all SKCS_PROTO_xxx definitions must be made - * external. - * - * SKCS_OVERWRITE_STATUS - Define to overwrite the default return status - * definitions. In this case, all SKCS_STATUS_xxx definitions must be made - * external. - * - * Include File Hierarchy: - * - * "h/skcsum.h" - * "h/sktypes.h" - * "h/skqueue.h" - * - ******************************************************************************/ - -#ifndef __INC_SKCSUM_H -#define __INC_SKCSUM_H - -#include "h/sktypes.h" -#include "h/skqueue.h" - -/* defines ********************************************************************/ - -/* - * Define the default bit flags for 'SKCS_PACKET_INFO.ProtocolFlags' if no user - * overwrite. - */ -#ifndef SKCS_OVERWRITE_PROTO /* User overwrite? */ -#define SKCS_PROTO_IP 0x1 /* IP (Internet Protocol version 4) */ -#define SKCS_PROTO_TCP 0x2 /* TCP (Transmission Control Protocol) */ -#define SKCS_PROTO_UDP 0x4 /* UDP (User Datagram Protocol) */ - -/* Indices for protocol statistics. */ -#define SKCS_PROTO_STATS_IP 0 -#define SKCS_PROTO_STATS_UDP 1 -#define SKCS_PROTO_STATS_TCP 2 -#define SKCS_NUM_PROTOCOLS 3 /* Number of supported protocols. */ -#endif /* !SKCS_OVERWRITE_PROTO */ - -/* - * Define the default SKCS_STATUS type and values if no user overwrite. - * - * SKCS_STATUS_UNKNOWN_IP_VERSION - Not an IP v4 frame. - * SKCS_STATUS_IP_CSUM_ERROR - IP checksum error. - * SKCS_STATUS_IP_CSUM_ERROR_TCP - IP checksum error in TCP frame. - * SKCS_STATUS_IP_CSUM_ERROR_UDP - IP checksum error in UDP frame - * SKCS_STATUS_IP_FRAGMENT - IP fragment (IP checksum ok). - * SKCS_STATUS_IP_CSUM_OK - IP checksum ok (not a TCP or UDP frame). - * SKCS_STATUS_TCP_CSUM_ERROR - TCP checksum error (IP checksum ok). - * SKCS_STATUS_UDP_CSUM_ERROR - UDP checksum error (IP checksum ok). - * SKCS_STATUS_TCP_CSUM_OK - IP and TCP checksum ok. - * SKCS_STATUS_UDP_CSUM_OK - IP and UDP checksum ok. - * SKCS_STATUS_IP_CSUM_OK_NO_UDP - IP checksum OK and no UDP checksum. - */ -#ifndef SKCS_OVERWRITE_STATUS /* User overwrite? */ -#define SKCS_STATUS int /* Define status type. */ - -#define SKCS_STATUS_UNKNOWN_IP_VERSION 1 -#define SKCS_STATUS_IP_CSUM_ERROR 2 -#define SKCS_STATUS_IP_FRAGMENT 3 -#define SKCS_STATUS_IP_CSUM_OK 4 -#define SKCS_STATUS_TCP_CSUM_ERROR 5 -#define SKCS_STATUS_UDP_CSUM_ERROR 6 -#define SKCS_STATUS_TCP_CSUM_OK 7 -#define SKCS_STATUS_UDP_CSUM_OK 8 -/* needed for Microsoft */ -#define SKCS_STATUS_IP_CSUM_ERROR_UDP 9 -#define SKCS_STATUS_IP_CSUM_ERROR_TCP 10 -/* UDP checksum may be omitted */ -#define SKCS_STATUS_IP_CSUM_OK_NO_UDP 11 -#endif /* !SKCS_OVERWRITE_STATUS */ - -/* Clear protocol statistics event. */ -#define SK_CSUM_EVENT_CLEAR_PROTO_STATS 1 - -/* - * Add two values in one's complement. - * - * Note: One of the two input values may be "longer" than 16-bit, but then the - * resulting sum may be 17 bits long. In this case, add zero to the result using - * SKCS_OC_ADD() again. - * - * Result = Value1 + Value2 - */ -#define SKCS_OC_ADD(Result, Value1, Value2) { \ - unsigned long Sum; \ - \ - Sum = (unsigned long) (Value1) + (unsigned long) (Value2); \ - /* Add-in any carry. */ \ - (Result) = (Sum & 0xffff) + (Sum >> 16); \ -} - -/* - * Subtract two values in one's complement. - * - * Result = Value1 - Value2 - */ -#define SKCS_OC_SUB(Result, Value1, Value2) \ - SKCS_OC_ADD((Result), (Value1), ~(Value2) & 0xffff) - -/* typedefs *******************************************************************/ - -/* - * SKCS_PROTO_STATS - The CSUM protocol statistics structure. - * - * There is one instance of this structure for each protocol supported. - */ -typedef struct s_CsProtocolStatistics { - SK_U64 RxOkCts; /* Receive checksum ok. */ - SK_U64 RxUnableCts; /* Unable to verify receive checksum. */ - SK_U64 RxErrCts; /* Receive checksum error. */ - SK_U64 TxOkCts; /* Transmit checksum ok. */ - SK_U64 TxUnableCts; /* Unable to calculate checksum in hw. */ -} SKCS_PROTO_STATS; - -/* - * s_Csum - The CSUM module context structure. - */ -typedef struct s_Csum { - /* Enabled receive SK_PROTO_XXX bit flags. */ - unsigned ReceiveFlags[SK_MAX_NETS]; -#ifdef TX_CSUM - unsigned TransmitFlags[SK_MAX_NETS]; -#endif /* TX_CSUM */ - - /* The protocol statistics structure; one per supported protocol. */ - SKCS_PROTO_STATS ProtoStats[SK_MAX_NETS][SKCS_NUM_PROTOCOLS]; -} SK_CSUM; - -/* - * SKCS_PACKET_INFO - The packet information structure. - */ -typedef struct s_CsPacketInfo { - /* Bit field specifiying the desired/found protocols. */ - unsigned ProtocolFlags; - - /* Length of complete IP header, including any option fields. */ - unsigned IpHeaderLength; - - /* IP header checksum. */ - unsigned IpHeaderChecksum; - - /* TCP/UDP pseudo header checksum. */ - unsigned PseudoHeaderChecksum; -} SKCS_PACKET_INFO; - -/* function prototypes ********************************************************/ - -#ifndef SK_CS_CALCULATE_CHECKSUM -extern unsigned SkCsCalculateChecksum( - void *pData, - unsigned Length); -#endif /* SK_CS_CALCULATE_CHECKSUM */ - -extern int SkCsEvent( - SK_AC *pAc, - SK_IOC Ioc, - SK_U32 Event, - SK_EVPARA Param); - -extern SKCS_STATUS SkCsGetReceiveInfo( - SK_AC *pAc, - void *pIpHeader, - unsigned Checksum1, - unsigned Checksum2, - int NetNumber); - -extern void SkCsSetReceiveFlags( - SK_AC *pAc, - unsigned ReceiveFlags, - unsigned *pChecksum1Offset, - unsigned *pChecksum2Offset, - int NetNumber); - -#endif /* __INC_SKCSUM_H */ diff --git a/drivers/net/sk98lin/h/skdebug.h b/drivers/net/sk98lin/h/skdebug.h deleted file mode 100644 index 3cba171d74b2..000000000000 --- a/drivers/net/sk98lin/h/skdebug.h +++ /dev/null @@ -1,74 +0,0 @@ -/****************************************************************************** - * - * Name: skdebug.h - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.14 $ - * Date: $Date: 2003/05/13 17:26:00 $ - * Purpose: SK specific DEBUG support - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef __INC_SKDEBUG_H -#define __INC_SKDEBUG_H - -#ifdef DEBUG -#ifndef SK_DBG_MSG -#define SK_DBG_MSG(pAC,comp,cat,arg) \ - if ( ((comp) & SK_DBG_CHKMOD(pAC)) && \ - ((cat) & SK_DBG_CHKCAT(pAC)) ) { \ - SK_DBG_PRINTF arg ; \ - } -#endif -#else -#define SK_DBG_MSG(pAC,comp,lev,arg) -#endif - -/* PLS NOTE: - * ========= - * Due to any restrictions of kernel printf routines do not use other - * format identifiers as: %x %d %c %s . - * Never use any combined format identifiers such as: %lx %ld in your - * printf - argument (arg) because some OS specific kernel printfs may - * only support some basic identifiers. - */ - -/* Debug modules */ - -#define SK_DBGMOD_MERR 0x00000001L /* general module error indication */ -#define SK_DBGMOD_HWM 0x00000002L /* Hardware init module */ -#define SK_DBGMOD_RLMT 0x00000004L /* RLMT module */ -#define SK_DBGMOD_VPD 0x00000008L /* VPD module */ -#define SK_DBGMOD_I2C 0x00000010L /* I2C module */ -#define SK_DBGMOD_PNMI 0x00000020L /* PNMI module */ -#define SK_DBGMOD_CSUM 0x00000040L /* CSUM module */ -#define SK_DBGMOD_ADDR 0x00000080L /* ADDR module */ -#define SK_DBGMOD_PECP 0x00000100L /* PECP module */ -#define SK_DBGMOD_POWM 0x00000200L /* Power Management module */ - -/* Debug events */ - -#define SK_DBGCAT_INIT 0x00000001L /* module/driver initialization */ -#define SK_DBGCAT_CTRL 0x00000002L /* controlling devices */ -#define SK_DBGCAT_ERR 0x00000004L /* error handling paths */ -#define SK_DBGCAT_TX 0x00000008L /* transmit path */ -#define SK_DBGCAT_RX 0x00000010L /* receive path */ -#define SK_DBGCAT_IRQ 0x00000020L /* general IRQ handling */ -#define SK_DBGCAT_QUEUE 0x00000040L /* any queue management */ -#define SK_DBGCAT_DUMP 0x00000080L /* large data output e.g. hex dump */ -#define SK_DBGCAT_FATAL 0x00000100L /* fatal error */ - -#endif /* __INC_SKDEBUG_H */ diff --git a/drivers/net/sk98lin/h/skdrv1st.h b/drivers/net/sk98lin/h/skdrv1st.h deleted file mode 100644 index 91b8d4f45904..000000000000 --- a/drivers/net/sk98lin/h/skdrv1st.h +++ /dev/null @@ -1,188 +0,0 @@ -/****************************************************************************** - * - * Name: skdrv1st.h - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.4 $ - * Date: $Date: 2003/11/12 14:28:14 $ - * Purpose: First header file for driver and all other modules - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * This is the first include file of the driver, which includes all - * neccessary system header files and some of the GEnesis header files. - * It also defines some basic items. - * - * Include File Hierarchy: - * - * see skge.c - * - ******************************************************************************/ - -#ifndef __INC_SKDRV1ST_H -#define __INC_SKDRV1ST_H - -typedef struct s_AC SK_AC; - -/* Set card versions */ -#define SK_FAR - -/* override some default functions with optimized linux functions */ - -#define SK_PNMI_STORE_U16(p,v) memcpy((char*)(p),(char*)&(v),2) -#define SK_PNMI_STORE_U32(p,v) memcpy((char*)(p),(char*)&(v),4) -#define SK_PNMI_STORE_U64(p,v) memcpy((char*)(p),(char*)&(v),8) -#define SK_PNMI_READ_U16(p,v) memcpy((char*)&(v),(char*)(p),2) -#define SK_PNMI_READ_U32(p,v) memcpy((char*)&(v),(char*)(p),4) -#define SK_PNMI_READ_U64(p,v) memcpy((char*)&(v),(char*)(p),8) - -#define SK_ADDR_EQUAL(a1,a2) (!memcmp(a1,a2,6)) - -#include <linux/types.h> -#include <linux/kernel.h> -#include <linux/string.h> -#include <linux/errno.h> -#include <linux/ioport.h> -#include <linux/slab.h> -#include <linux/interrupt.h> -#include <linux/pci.h> -#include <linux/bitops.h> -#include <asm/byteorder.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> - -#include <linux/init.h> -#include <asm/uaccess.h> -#include <net/checksum.h> - -#define SK_CS_CALCULATE_CHECKSUM -#ifndef CONFIG_X86_64 -#define SkCsCalculateChecksum(p,l) ((~ip_compute_csum(p, l)) & 0xffff) -#else -#define SkCsCalculateChecksum(p,l) ((~ip_fast_csum(p, l)) & 0xffff) -#endif - -#include "h/sktypes.h" -#include "h/skerror.h" -#include "h/skdebug.h" -#include "h/lm80.h" -#include "h/xmac_ii.h" - -#ifdef __LITTLE_ENDIAN -#define SK_LITTLE_ENDIAN -#else -#define SK_BIG_ENDIAN -#endif - -#define SK_NET_DEVICE net_device - - -/* we use gethrtime(), return unit: nanoseconds */ -#define SK_TICKS_PER_SEC 100 - -#define SK_MEM_MAPPED_IO - -// #define SK_RLMT_SLOW_LOOKAHEAD - -#define SK_MAX_MACS 2 -#define SK_MAX_NETS 2 - -#define SK_IOC char __iomem * - -typedef struct s_DrvRlmtMbuf SK_MBUF; - -#define SK_CONST64 INT64_C -#define SK_CONSTU64 UINT64_C - -#define SK_MEMCPY(dest,src,size) memcpy(dest,src,size) -#define SK_MEMCMP(s1,s2,size) memcmp(s1,s2,size) -#define SK_MEMSET(dest,val,size) memset(dest,val,size) -#define SK_STRLEN(pStr) strlen((char*)(pStr)) -#define SK_STRNCPY(pDest,pSrc,size) strncpy((char*)(pDest),(char*)(pSrc),size) -#define SK_STRCMP(pStr1,pStr2) strcmp((char*)(pStr1),(char*)(pStr2)) - -/* macros to access the adapter */ -#define SK_OUT8(b,a,v) writeb((v), ((b)+(a))) -#define SK_OUT16(b,a,v) writew((v), ((b)+(a))) -#define SK_OUT32(b,a,v) writel((v), ((b)+(a))) -#define SK_IN8(b,a,pv) (*(pv) = readb((b)+(a))) -#define SK_IN16(b,a,pv) (*(pv) = readw((b)+(a))) -#define SK_IN32(b,a,pv) (*(pv) = readl((b)+(a))) - -#define int8_t char -#define int16_t short -#define int32_t long -#define int64_t long long -#define uint8_t u_char -#define uint16_t u_short -#define uint32_t u_long -#define uint64_t unsigned long long -#define t_scalar_t int -#define t_uscalar_t unsigned int -#define uintptr_t unsigned long - -#define __CONCAT__(A,B) A##B - -#define INT32_C(a) __CONCAT__(a,L) -#define INT64_C(a) __CONCAT__(a,LL) -#define UINT32_C(a) __CONCAT__(a,UL) -#define UINT64_C(a) __CONCAT__(a,ULL) - -#ifdef DEBUG -#define SK_DBG_PRINTF printk -#ifndef SK_DEBUG_CHKMOD -#define SK_DEBUG_CHKMOD 0 -#endif -#ifndef SK_DEBUG_CHKCAT -#define SK_DEBUG_CHKCAT 0 -#endif -/* those come from the makefile */ -#define SK_DBG_CHKMOD(pAC) (SK_DEBUG_CHKMOD) -#define SK_DBG_CHKCAT(pAC) (SK_DEBUG_CHKCAT) - -extern void SkDbgPrintf(const char *format,...); - -#define SK_DBGMOD_DRV 0x00010000 - -/**** possible driver debug categories ********************************/ -#define SK_DBGCAT_DRV_ENTRY 0x00010000 -#define SK_DBGCAT_DRV_SAP 0x00020000 -#define SK_DBGCAT_DRV_MCA 0x00040000 -#define SK_DBGCAT_DRV_TX_PROGRESS 0x00080000 -#define SK_DBGCAT_DRV_RX_PROGRESS 0x00100000 -#define SK_DBGCAT_DRV_PROGRESS 0x00200000 -#define SK_DBGCAT_DRV_MSG 0x00400000 -#define SK_DBGCAT_DRV_PROM 0x00800000 -#define SK_DBGCAT_DRV_TX_FRAME 0x01000000 -#define SK_DBGCAT_DRV_ERROR 0x02000000 -#define SK_DBGCAT_DRV_INT_SRC 0x04000000 -#define SK_DBGCAT_DRV_EVENT 0x08000000 - -#endif - -#define SK_ERR_LOG SkErrorLog - -extern void SkErrorLog(SK_AC*, int, int, char*); - -#endif - diff --git a/drivers/net/sk98lin/h/skdrv2nd.h b/drivers/net/sk98lin/h/skdrv2nd.h deleted file mode 100644 index 3fa67171e832..000000000000 --- a/drivers/net/sk98lin/h/skdrv2nd.h +++ /dev/null @@ -1,447 +0,0 @@ -/****************************************************************************** - * - * Name: skdrv2nd.h - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.10 $ - * Date: $Date: 2003/12/11 16:04:45 $ - * Purpose: Second header file for driver and all other modules - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * This is the second include file of the driver, which includes all other - * neccessary files and defines all structures and constants used by the - * driver and the common modules. - * - * Include File Hierarchy: - * - * see skge.c - * - ******************************************************************************/ - -#ifndef __INC_SKDRV2ND_H -#define __INC_SKDRV2ND_H - -#include "h/skqueue.h" -#include "h/skgehwt.h" -#include "h/sktimer.h" -#include "h/ski2c.h" -#include "h/skgepnmi.h" -#include "h/skvpd.h" -#include "h/skgehw.h" -#include "h/skgeinit.h" -#include "h/skaddr.h" -#include "h/skgesirq.h" -#include "h/skcsum.h" -#include "h/skrlmt.h" -#include "h/skgedrv.h" - - -extern SK_MBUF *SkDrvAllocRlmtMbuf(SK_AC*, SK_IOC, unsigned); -extern void SkDrvFreeRlmtMbuf(SK_AC*, SK_IOC, SK_MBUF*); -extern SK_U64 SkOsGetTime(SK_AC*); -extern int SkPciReadCfgDWord(SK_AC*, int, SK_U32*); -extern int SkPciReadCfgWord(SK_AC*, int, SK_U16*); -extern int SkPciReadCfgByte(SK_AC*, int, SK_U8*); -extern int SkPciWriteCfgWord(SK_AC*, int, SK_U16); -extern int SkPciWriteCfgByte(SK_AC*, int, SK_U8); -extern int SkDrvEvent(SK_AC*, SK_IOC IoC, SK_U32, SK_EVPARA); - -#ifdef SK_DIAG_SUPPORT -extern int SkDrvEnterDiagMode(SK_AC *pAc); -extern int SkDrvLeaveDiagMode(SK_AC *pAc); -#endif - -struct s_DrvRlmtMbuf { - SK_MBUF *pNext; /* Pointer to next RLMT Mbuf. */ - SK_U8 *pData; /* Data buffer (virtually contig.). */ - unsigned Size; /* Data buffer size. */ - unsigned Length; /* Length of packet (<= Size). */ - SK_U32 PortIdx; /* Receiving/transmitting port. */ -#ifdef SK_RLMT_MBUF_PRIVATE - SK_RLMT_MBUF Rlmt; /* Private part for RLMT. */ -#endif /* SK_RLMT_MBUF_PRIVATE */ - struct sk_buff *pOs; /* Pointer to message block */ -}; - - -/* - * Time macros - */ -#if SK_TICKS_PER_SEC == 100 -#define SK_PNMI_HUNDREDS_SEC(t) (t) -#else -#define SK_PNMI_HUNDREDS_SEC(t) ((((unsigned long)t) * 100) / \ - (SK_TICKS_PER_SEC)) -#endif - -/* - * New SkOsGetTime - */ -#define SkOsGetTimeCurrent(pAC, pUsec) {\ - struct timeval t;\ - do_gettimeofday(&t);\ - *pUsec = ((((t.tv_sec) * 1000000L)+t.tv_usec)/10000);\ -} - - -/* - * ioctl definitions - */ -#define SK_IOCTL_BASE (SIOCDEVPRIVATE) -#define SK_IOCTL_GETMIB (SK_IOCTL_BASE + 0) -#define SK_IOCTL_SETMIB (SK_IOCTL_BASE + 1) -#define SK_IOCTL_PRESETMIB (SK_IOCTL_BASE + 2) -#define SK_IOCTL_GEN (SK_IOCTL_BASE + 3) -#define SK_IOCTL_DIAG (SK_IOCTL_BASE + 4) - -typedef struct s_IOCTL SK_GE_IOCTL; - -struct s_IOCTL { - char __user * pData; - unsigned int Len; -}; - - -/* - * define sizes of descriptor rings in bytes - */ - -#define TX_RING_SIZE (8*1024) -#define RX_RING_SIZE (24*1024) - -/* - * Buffer size for ethernet packets - */ -#define ETH_BUF_SIZE 1540 -#define ETH_MAX_MTU 1514 -#define ETH_MIN_MTU 60 -#define ETH_MULTICAST_BIT 0x01 -#define SK_JUMBO_MTU 9000 - -/* - * transmit priority selects the queue: LOW=asynchron, HIGH=synchron - */ -#define TX_PRIO_LOW 0 -#define TX_PRIO_HIGH 1 - -/* - * alignment of rx/tx descriptors - */ -#define DESCR_ALIGN 64 - -/* - * definitions for pnmi. TODO - */ -#define SK_DRIVER_RESET(pAC, IoC) 0 -#define SK_DRIVER_SENDEVENT(pAC, IoC) 0 -#define SK_DRIVER_SELFTEST(pAC, IoC) 0 -/* For get mtu you must add an own function */ -#define SK_DRIVER_GET_MTU(pAc,IoC,i) 0 -#define SK_DRIVER_SET_MTU(pAc,IoC,i,v) 0 -#define SK_DRIVER_PRESET_MTU(pAc,IoC,i,v) 0 - -/* -** Interim definition of SK_DRV_TIMER placed in this file until -** common modules have been finalized -*/ -#define SK_DRV_TIMER 11 -#define SK_DRV_MODERATION_TIMER 1 -#define SK_DRV_MODERATION_TIMER_LENGTH 1000000 /* 1 second */ -#define SK_DRV_RX_CLEANUP_TIMER 2 -#define SK_DRV_RX_CLEANUP_TIMER_LENGTH 1000000 /* 100 millisecs */ - -/* -** Definitions regarding transmitting frames -** any calculating any checksum. -*/ -#define C_LEN_ETHERMAC_HEADER_DEST_ADDR 6 -#define C_LEN_ETHERMAC_HEADER_SRC_ADDR 6 -#define C_LEN_ETHERMAC_HEADER_LENTYPE 2 -#define C_LEN_ETHERMAC_HEADER ( (C_LEN_ETHERMAC_HEADER_DEST_ADDR) + \ - (C_LEN_ETHERMAC_HEADER_SRC_ADDR) + \ - (C_LEN_ETHERMAC_HEADER_LENTYPE) ) - -#define C_LEN_ETHERMTU_MINSIZE 46 -#define C_LEN_ETHERMTU_MAXSIZE_STD 1500 -#define C_LEN_ETHERMTU_MAXSIZE_JUMBO 9000 - -#define C_LEN_ETHERNET_MINSIZE ( (C_LEN_ETHERMAC_HEADER) + \ - (C_LEN_ETHERMTU_MINSIZE) ) - -#define C_OFFSET_IPHEADER C_LEN_ETHERMAC_HEADER -#define C_OFFSET_IPHEADER_IPPROTO 9 -#define C_OFFSET_TCPHEADER_TCPCS 16 -#define C_OFFSET_UDPHEADER_UDPCS 6 - -#define C_OFFSET_IPPROTO ( (C_LEN_ETHERMAC_HEADER) + \ - (C_OFFSET_IPHEADER_IPPROTO) ) - -#define C_PROTO_ID_UDP 17 /* refer to RFC 790 or Stevens' */ -#define C_PROTO_ID_TCP 6 /* TCP/IP illustrated for details */ - -/* TX and RX descriptors *****************************************************/ - -typedef struct s_RxD RXD; /* the receive descriptor */ - -struct s_RxD { - volatile SK_U32 RBControl; /* Receive Buffer Control */ - SK_U32 VNextRxd; /* Next receive descriptor,low dword */ - SK_U32 VDataLow; /* Receive buffer Addr, low dword */ - SK_U32 VDataHigh; /* Receive buffer Addr, high dword */ - SK_U32 FrameStat; /* Receive Frame Status word */ - SK_U32 TimeStamp; /* Time stamp from XMAC */ - SK_U32 TcpSums; /* TCP Sum 2 / TCP Sum 1 */ - SK_U32 TcpSumStarts; /* TCP Sum Start 2 / TCP Sum Start 1 */ - RXD *pNextRxd; /* Pointer to next Rxd */ - struct sk_buff *pMBuf; /* Pointer to Linux' socket buffer */ -}; - -typedef struct s_TxD TXD; /* the transmit descriptor */ - -struct s_TxD { - volatile SK_U32 TBControl; /* Transmit Buffer Control */ - SK_U32 VNextTxd; /* Next transmit descriptor,low dword */ - SK_U32 VDataLow; /* Transmit Buffer Addr, low dword */ - SK_U32 VDataHigh; /* Transmit Buffer Addr, high dword */ - SK_U32 FrameStat; /* Transmit Frame Status Word */ - SK_U32 TcpSumOfs; /* Reserved / TCP Sum Offset */ - SK_U16 TcpSumSt; /* TCP Sum Start */ - SK_U16 TcpSumWr; /* TCP Sum Write */ - SK_U32 TcpReserved; /* not used */ - TXD *pNextTxd; /* Pointer to next Txd */ - struct sk_buff *pMBuf; /* Pointer to Linux' socket buffer */ -}; - -/* Used interrupt bits in the interrupts source register *********************/ - -#define DRIVER_IRQS ((IS_IRQ_SW) | \ - (IS_R1_F) |(IS_R2_F) | \ - (IS_XS1_F) |(IS_XA1_F) | \ - (IS_XS2_F) |(IS_XA2_F)) - -#define SPECIAL_IRQS ((IS_HW_ERR) |(IS_I2C_READY) | \ - (IS_EXT_REG) |(IS_TIMINT) | \ - (IS_PA_TO_RX1) |(IS_PA_TO_RX2) | \ - (IS_PA_TO_TX1) |(IS_PA_TO_TX2) | \ - (IS_MAC1) |(IS_LNK_SYNC_M1)| \ - (IS_MAC2) |(IS_LNK_SYNC_M2)| \ - (IS_R1_C) |(IS_R2_C) | \ - (IS_XS1_C) |(IS_XA1_C) | \ - (IS_XS2_C) |(IS_XA2_C)) - -#define IRQ_MASK ((IS_IRQ_SW) | \ - (IS_R1_B) |(IS_R1_F) |(IS_R2_B) |(IS_R2_F) | \ - (IS_XS1_B) |(IS_XS1_F) |(IS_XA1_B)|(IS_XA1_F)| \ - (IS_XS2_B) |(IS_XS2_F) |(IS_XA2_B)|(IS_XA2_F)| \ - (IS_HW_ERR) |(IS_I2C_READY)| \ - (IS_EXT_REG) |(IS_TIMINT) | \ - (IS_PA_TO_RX1) |(IS_PA_TO_RX2)| \ - (IS_PA_TO_TX1) |(IS_PA_TO_TX2)| \ - (IS_MAC1) |(IS_MAC2) | \ - (IS_R1_C) |(IS_R2_C) | \ - (IS_XS1_C) |(IS_XA1_C) | \ - (IS_XS2_C) |(IS_XA2_C)) - -#define IRQ_HWE_MASK (IS_ERR_MSK) /* enable all HW irqs */ - -typedef struct s_DevNet DEV_NET; - -struct s_DevNet { - int PortNr; - int NetNr; - SK_AC *pAC; -}; - -typedef struct s_TxPort TX_PORT; - -struct s_TxPort { - /* the transmit descriptor rings */ - caddr_t pTxDescrRing; /* descriptor area memory */ - SK_U64 VTxDescrRing; /* descr. area bus virt. addr. */ - TXD *pTxdRingHead; /* Head of Tx rings */ - TXD *pTxdRingTail; /* Tail of Tx rings */ - TXD *pTxdRingPrev; /* descriptor sent previously */ - int TxdRingFree; /* # of free entrys */ - spinlock_t TxDesRingLock; /* serialize descriptor accesses */ - SK_IOC HwAddr; /* bmu registers address */ - int PortIndex; /* index number of port (0 or 1) */ -}; - -typedef struct s_RxPort RX_PORT; - -struct s_RxPort { - /* the receive descriptor rings */ - caddr_t pRxDescrRing; /* descriptor area memory */ - SK_U64 VRxDescrRing; /* descr. area bus virt. addr. */ - RXD *pRxdRingHead; /* Head of Rx rings */ - RXD *pRxdRingTail; /* Tail of Rx rings */ - RXD *pRxdRingPrev; /* descriptor given to BMU previously */ - int RxdRingFree; /* # of free entrys */ - int RxCsum; /* use receive checksum hardware */ - spinlock_t RxDesRingLock; /* serialize descriptor accesses */ - int RxFillLimit; /* limit for buffers in ring */ - SK_IOC HwAddr; /* bmu registers address */ - int PortIndex; /* index number of port (0 or 1) */ -}; - -/* Definitions needed for interrupt moderation *******************************/ - -#define IRQ_EOF_AS_TX ((IS_XA1_F) | (IS_XA2_F)) -#define IRQ_EOF_SY_TX ((IS_XS1_F) | (IS_XS2_F)) -#define IRQ_MASK_TX_ONLY ((IRQ_EOF_AS_TX)| (IRQ_EOF_SY_TX)) -#define IRQ_MASK_RX_ONLY ((IS_R1_F) | (IS_R2_F)) -#define IRQ_MASK_SP_ONLY (SPECIAL_IRQS) -#define IRQ_MASK_TX_RX ((IRQ_MASK_TX_ONLY)| (IRQ_MASK_RX_ONLY)) -#define IRQ_MASK_SP_RX ((SPECIAL_IRQS) | (IRQ_MASK_RX_ONLY)) -#define IRQ_MASK_SP_TX ((SPECIAL_IRQS) | (IRQ_MASK_TX_ONLY)) -#define IRQ_MASK_RX_TX_SP ((SPECIAL_IRQS) | (IRQ_MASK_TX_RX)) - -#define C_INT_MOD_NONE 1 -#define C_INT_MOD_STATIC 2 -#define C_INT_MOD_DYNAMIC 4 - -#define C_CLK_FREQ_GENESIS 53215000 /* shorter: 53.125 MHz */ -#define C_CLK_FREQ_YUKON 78215000 /* shorter: 78.125 MHz */ - -#define C_INTS_PER_SEC_DEFAULT 2000 -#define C_INT_MOD_ENABLE_PERCENTAGE 50 /* if higher 50% enable */ -#define C_INT_MOD_DISABLE_PERCENTAGE 50 /* if lower 50% disable */ -#define C_INT_MOD_IPS_LOWER_RANGE 30 -#define C_INT_MOD_IPS_UPPER_RANGE 40000 - - -typedef struct s_DynIrqModInfo DIM_INFO; -struct s_DynIrqModInfo { - unsigned long PrevTimeVal; - unsigned int PrevSysLoad; - unsigned int PrevUsedTime; - unsigned int PrevTotalTime; - int PrevUsedDescrRatio; - int NbrProcessedDescr; - SK_U64 PrevPort0RxIntrCts; - SK_U64 PrevPort1RxIntrCts; - SK_U64 PrevPort0TxIntrCts; - SK_U64 PrevPort1TxIntrCts; - SK_BOOL ModJustEnabled; /* Moderation just enabled yes/no */ - - int MaxModIntsPerSec; /* Moderation Threshold */ - int MaxModIntsPerSecUpperLimit; /* Upper limit for DIM */ - int MaxModIntsPerSecLowerLimit; /* Lower limit for DIM */ - - long MaskIrqModeration; /* ModIrqType (eg. 'TxRx') */ - SK_BOOL DisplayStats; /* Stats yes/no */ - SK_BOOL AutoSizing; /* Resize DIM-timer on/off */ - int IntModTypeSelect; /* EnableIntMod (eg. 'dynamic') */ - - SK_TIMER ModTimer; /* just some timer */ -}; - -typedef struct s_PerStrm PER_STRM; - -#define SK_ALLOC_IRQ 0x00000001 - -#ifdef SK_DIAG_SUPPORT -#define DIAG_ACTIVE 1 -#define DIAG_NOTACTIVE 0 -#endif - -/**************************************************************************** - * Per board structure / Adapter Context structure: - * Allocated within attach(9e) and freed within detach(9e). - * Contains all 'per device' necessary handles, flags, locks etc.: - */ -struct s_AC { - SK_GEINIT GIni; /* GE init struct */ - SK_PNMI Pnmi; /* PNMI data struct */ - SK_VPD vpd; /* vpd data struct */ - SK_QUEUE Event; /* Event queue */ - SK_HWT Hwt; /* Hardware Timer control struct */ - SK_TIMCTRL Tim; /* Software Timer control struct */ - SK_I2C I2c; /* I2C relevant data structure */ - SK_ADDR Addr; /* for Address module */ - SK_CSUM Csum; /* for checksum module */ - SK_RLMT Rlmt; /* for rlmt module */ - spinlock_t SlowPathLock; /* Normal IRQ lock */ - struct timer_list BlinkTimer; /* for LED blinking */ - int LedsOn; - SK_PNMI_STRUCT_DATA PnmiStruct; /* structure to get all Pnmi-Data */ - int RlmtMode; /* link check mode to set */ - int RlmtNets; /* Number of nets */ - - SK_IOC IoBase; /* register set of adapter */ - int BoardLevel; /* level of active hw init (0-2) */ - - SK_U32 AllocFlag; /* flag allocation of resources */ - struct pci_dev *PciDev; /* for access to pci config space */ - struct SK_NET_DEVICE *dev[2]; /* pointer to device struct */ - - int RxBufSize; /* length of receive buffers */ - struct net_device_stats stats; /* linux 'netstat -i' statistics */ - int Index; /* internal board index number */ - - /* adapter RAM sizes for queues of active port */ - int RxQueueSize; /* memory used for receive queue */ - int TxSQueueSize; /* memory used for sync. tx queue */ - int TxAQueueSize; /* memory used for async. tx queue */ - - int PromiscCount; /* promiscuous mode counter */ - int AllMultiCount; /* allmulticast mode counter */ - int MulticCount; /* number of different MC */ - /* addresses for this board */ - /* (may be more than HW can)*/ - - int HWRevision; /* Hardware revision */ - int ActivePort; /* the active XMAC port */ - int MaxPorts; /* number of activated ports */ - int TxDescrPerRing; /* # of descriptors per tx ring */ - int RxDescrPerRing; /* # of descriptors per rx ring */ - - caddr_t pDescrMem; /* Pointer to the descriptor area */ - dma_addr_t pDescrMemDMA; /* PCI DMA address of area */ - - /* the port structures with descriptor rings */ - TX_PORT TxPort[SK_MAX_MACS][2]; - RX_PORT RxPort[SK_MAX_MACS]; - - SK_BOOL CheckQueue; /* check event queue soon */ - SK_TIMER DrvCleanupTimer;/* to check for pending descriptors */ - DIM_INFO DynIrqModInfo; /* all data related to DIM */ - - /* Only for tests */ - int PortDown; - int ChipsetType; /* Chipset family type - * 0 == Genesis family support - * 1 == Yukon family support - */ -#ifdef SK_DIAG_SUPPORT - SK_U32 DiagModeActive; /* is diag active? */ - SK_BOOL DiagFlowCtrl; /* for control purposes */ - SK_PNMI_STRUCT_DATA PnmiBackup; /* backup structure for all Pnmi-Data */ - SK_BOOL WasIfUp[SK_MAX_MACS]; /* for OpenClose while - * DIAG is busy with NIC - */ -#endif - -}; - - -#endif /* __INC_SKDRV2ND_H */ - diff --git a/drivers/net/sk98lin/h/skerror.h b/drivers/net/sk98lin/h/skerror.h deleted file mode 100644 index da062f766238..000000000000 --- a/drivers/net/sk98lin/h/skerror.h +++ /dev/null @@ -1,55 +0,0 @@ -/****************************************************************************** - * - * Name: skerror.h - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.7 $ - * Date: $Date: 2003/05/13 17:25:13 $ - * Purpose: SK specific Error log support - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef _INC_SKERROR_H_ -#define _INC_SKERROR_H_ - -/* - * Define Error Classes - */ -#define SK_ERRCL_OTHER (0) /* Other error */ -#define SK_ERRCL_CONFIG (1L<<0) /* Configuration error */ -#define SK_ERRCL_INIT (1L<<1) /* Initialization error */ -#define SK_ERRCL_NORES (1L<<2) /* Out of Resources error */ -#define SK_ERRCL_SW (1L<<3) /* Internal Software error */ -#define SK_ERRCL_HW (1L<<4) /* Hardware Failure */ -#define SK_ERRCL_COMM (1L<<5) /* Communication error */ - - -/* - * Define Error Code Bases - */ -#define SK_ERRBASE_RLMT 100 /* Base Error number for RLMT */ -#define SK_ERRBASE_HWINIT 200 /* Base Error number for HWInit */ -#define SK_ERRBASE_VPD 300 /* Base Error number for VPD */ -#define SK_ERRBASE_PNMI 400 /* Base Error number for PNMI */ -#define SK_ERRBASE_CSUM 500 /* Base Error number for Checksum */ -#define SK_ERRBASE_SIRQ 600 /* Base Error number for Special IRQ */ -#define SK_ERRBASE_I2C 700 /* Base Error number for I2C module */ -#define SK_ERRBASE_QUEUE 800 /* Base Error number for Scheduler */ -#define SK_ERRBASE_ADDR 900 /* Base Error number for Address module */ -#define SK_ERRBASE_PECP 1000 /* Base Error number for PECP */ -#define SK_ERRBASE_DRV 1100 /* Base Error number for Driver */ - -#endif /* _INC_SKERROR_H_ */ diff --git a/drivers/net/sk98lin/h/skgedrv.h b/drivers/net/sk98lin/h/skgedrv.h deleted file mode 100644 index 44fd4c3de818..000000000000 --- a/drivers/net/sk98lin/h/skgedrv.h +++ /dev/null @@ -1,51 +0,0 @@ -/****************************************************************************** - * - * Name: skgedrv.h - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.10 $ - * Date: $Date: 2003/07/04 12:25:01 $ - * Purpose: Interface with the driver - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef __INC_SKGEDRV_H_ -#define __INC_SKGEDRV_H_ - -/* defines ********************************************************************/ - -/* - * Define the driver events. - * Usually the events are defined by the destination module. - * In case of the driver we put the definition of the events here. - */ -#define SK_DRV_PORT_RESET 1 /* The port needs to be reset */ -#define SK_DRV_NET_UP 2 /* The net is operational */ -#define SK_DRV_NET_DOWN 3 /* The net is down */ -#define SK_DRV_SWITCH_SOFT 4 /* Ports switch with both links connected */ -#define SK_DRV_SWITCH_HARD 5 /* Port switch due to link failure */ -#define SK_DRV_RLMT_SEND 6 /* Send a RLMT packet */ -#define SK_DRV_ADAP_FAIL 7 /* The whole adapter fails */ -#define SK_DRV_PORT_FAIL 8 /* One port fails */ -#define SK_DRV_SWITCH_INTERN 9 /* Port switch by the driver itself */ -#define SK_DRV_POWER_DOWN 10 /* Power down mode */ -#define SK_DRV_TIMER 11 /* Timer for free use */ -#ifdef SK_NO_RLMT -#define SK_DRV_LINK_UP 12 /* Link Up event for driver */ -#define SK_DRV_LINK_DOWN 13 /* Link Down event for driver */ -#endif -#define SK_DRV_DOWNSHIFT_DET 14 /* Downshift 4-Pair / 2-Pair (YUKON only) */ -#endif /* __INC_SKGEDRV_H_ */ diff --git a/drivers/net/sk98lin/h/skgehw.h b/drivers/net/sk98lin/h/skgehw.h deleted file mode 100644 index f6282b7956db..000000000000 --- a/drivers/net/sk98lin/h/skgehw.h +++ /dev/null @@ -1,2126 +0,0 @@ -/****************************************************************************** - * - * Name: skgehw.h - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.56 $ - * Date: $Date: 2003/09/23 09:01:00 $ - * Purpose: Defines and Macros for the Gigabit Ethernet Adapter Product Family - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef __INC_SKGEHW_H -#define __INC_SKGEHW_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/* defines ********************************************************************/ - -#define BIT_31 (1UL << 31) -#define BIT_30 (1L << 30) -#define BIT_29 (1L << 29) -#define BIT_28 (1L << 28) -#define BIT_27 (1L << 27) -#define BIT_26 (1L << 26) -#define BIT_25 (1L << 25) -#define BIT_24 (1L << 24) -#define BIT_23 (1L << 23) -#define BIT_22 (1L << 22) -#define BIT_21 (1L << 21) -#define BIT_20 (1L << 20) -#define BIT_19 (1L << 19) -#define BIT_18 (1L << 18) -#define BIT_17 (1L << 17) -#define BIT_16 (1L << 16) -#define BIT_15 (1L << 15) -#define BIT_14 (1L << 14) -#define BIT_13 (1L << 13) -#define BIT_12 (1L << 12) -#define BIT_11 (1L << 11) -#define BIT_10 (1L << 10) -#define BIT_9 (1L << 9) -#define BIT_8 (1L << 8) -#define BIT_7 (1L << 7) -#define BIT_6 (1L << 6) -#define BIT_5 (1L << 5) -#define BIT_4 (1L << 4) -#define BIT_3 (1L << 3) -#define BIT_2 (1L << 2) -#define BIT_1 (1L << 1) -#define BIT_0 1L - -#define BIT_15S (1U << 15) -#define BIT_14S (1 << 14) -#define BIT_13S (1 << 13) -#define BIT_12S (1 << 12) -#define BIT_11S (1 << 11) -#define BIT_10S (1 << 10) -#define BIT_9S (1 << 9) -#define BIT_8S (1 << 8) -#define BIT_7S (1 << 7) -#define BIT_6S (1 << 6) -#define BIT_5S (1 << 5) -#define BIT_4S (1 << 4) -#define BIT_3S (1 << 3) -#define BIT_2S (1 << 2) -#define BIT_1S (1 << 1) -#define BIT_0S 1 - -#define SHIFT31(x) ((x) << 31) -#define SHIFT30(x) ((x) << 30) -#define SHIFT29(x) ((x) << 29) -#define SHIFT28(x) ((x) << 28) -#define SHIFT27(x) ((x) << 27) -#define SHIFT26(x) ((x) << 26) -#define SHIFT25(x) ((x) << 25) -#define SHIFT24(x) ((x) << 24) -#define SHIFT23(x) ((x) << 23) -#define SHIFT22(x) ((x) << 22) -#define SHIFT21(x) ((x) << 21) -#define SHIFT20(x) ((x) << 20) -#define SHIFT19(x) ((x) << 19) -#define SHIFT18(x) ((x) << 18) -#define SHIFT17(x) ((x) << 17) -#define SHIFT16(x) ((x) << 16) -#define SHIFT15(x) ((x) << 15) -#define SHIFT14(x) ((x) << 14) -#define SHIFT13(x) ((x) << 13) -#define SHIFT12(x) ((x) << 12) -#define SHIFT11(x) ((x) << 11) -#define SHIFT10(x) ((x) << 10) -#define SHIFT9(x) ((x) << 9) -#define SHIFT8(x) ((x) << 8) -#define SHIFT7(x) ((x) << 7) -#define SHIFT6(x) ((x) << 6) -#define SHIFT5(x) ((x) << 5) -#define SHIFT4(x) ((x) << 4) -#define SHIFT3(x) ((x) << 3) -#define SHIFT2(x) ((x) << 2) -#define SHIFT1(x) ((x) << 1) -#define SHIFT0(x) ((x) << 0) - -/* - * Configuration Space header - * Since this module is used for different OS', those may be - * duplicate on some of them (e.g. Linux). But to keep the - * common source, we have to live with this... - */ -#define PCI_VENDOR_ID 0x00 /* 16 bit Vendor ID */ -#define PCI_DEVICE_ID 0x02 /* 16 bit Device ID */ -#define PCI_COMMAND 0x04 /* 16 bit Command */ -#define PCI_STATUS 0x06 /* 16 bit Status */ -#define PCI_REV_ID 0x08 /* 8 bit Revision ID */ -#define PCI_CLASS_CODE 0x09 /* 24 bit Class Code */ -#define PCI_CACHE_LSZ 0x0c /* 8 bit Cache Line Size */ -#define PCI_LAT_TIM 0x0d /* 8 bit Latency Timer */ -#define PCI_HEADER_T 0x0e /* 8 bit Header Type */ -#define PCI_BIST 0x0f /* 8 bit Built-in selftest */ -#define PCI_BASE_1ST 0x10 /* 32 bit 1st Base address */ -#define PCI_BASE_2ND 0x14 /* 32 bit 2nd Base address */ - /* Byte 0x18..0x2b: reserved */ -#define PCI_SUB_VID 0x2c /* 16 bit Subsystem Vendor ID */ -#define PCI_SUB_ID 0x2e /* 16 bit Subsystem ID */ -#define PCI_BASE_ROM 0x30 /* 32 bit Expansion ROM Base Address */ -#define PCI_CAP_PTR 0x34 /* 8 bit Capabilities Ptr */ - /* Byte 0x35..0x3b: reserved */ -#define PCI_IRQ_LINE 0x3c /* 8 bit Interrupt Line */ -#define PCI_IRQ_PIN 0x3d /* 8 bit Interrupt Pin */ -#define PCI_MIN_GNT 0x3e /* 8 bit Min_Gnt */ -#define PCI_MAX_LAT 0x3f /* 8 bit Max_Lat */ - /* Device Dependent Region */ -#define PCI_OUR_REG_1 0x40 /* 32 bit Our Register 1 */ -#define PCI_OUR_REG_2 0x44 /* 32 bit Our Register 2 */ - /* Power Management Region */ -#define PCI_PM_CAP_ID 0x48 /* 8 bit Power Management Cap. ID */ -#define PCI_PM_NITEM 0x49 /* 8 bit Next Item Ptr */ -#define PCI_PM_CAP_REG 0x4a /* 16 bit Power Management Capabilities */ -#define PCI_PM_CTL_STS 0x4c /* 16 bit Power Manag. Control/Status */ - /* Byte 0x4e: reserved */ -#define PCI_PM_DAT_REG 0x4f /* 8 bit Power Manag. Data Register */ - /* VPD Region */ -#define PCI_VPD_CAP_ID 0x50 /* 8 bit VPD Cap. ID */ -#define PCI_VPD_NITEM 0x51 /* 8 bit Next Item Ptr */ -#define PCI_VPD_ADR_REG 0x52 /* 16 bit VPD Address Register */ -#define PCI_VPD_DAT_REG 0x54 /* 32 bit VPD Data Register */ - /* Byte 0x58..0x59: reserved */ -#define PCI_SER_LD_CTRL 0x5a /* 16 bit SEEPROM Loader Ctrl (YUKON only) */ - /* Byte 0x5c..0xff: reserved */ - -/* - * I2C Address (PCI Config) - * - * Note: The temperature and voltage sensors are relocated on a different - * I2C bus. - */ -#define I2C_ADDR_VPD 0xa0 /* I2C address for the VPD EEPROM */ - -/* - * Define Bits and Values of the registers - */ -/* PCI_COMMAND 16 bit Command */ - /* Bit 15..11: reserved */ -#define PCI_INT_DIS BIT_10S /* Interrupt INTx# disable (PCI 2.3) */ -#define PCI_FBTEN BIT_9S /* Fast Back-To-Back enable */ -#define PCI_SERREN BIT_8S /* SERR enable */ -#define PCI_ADSTEP BIT_7S /* Address Stepping */ -#define PCI_PERREN BIT_6S /* Parity Report Response enable */ -#define PCI_VGA_SNOOP BIT_5S /* VGA palette snoop */ -#define PCI_MWIEN BIT_4S /* Memory write an inv cycl ena */ -#define PCI_SCYCEN BIT_3S /* Special Cycle enable */ -#define PCI_BMEN BIT_2S /* Bus Master enable */ -#define PCI_MEMEN BIT_1S /* Memory Space Access enable */ -#define PCI_IOEN BIT_0S /* I/O Space Access enable */ - -#define PCI_COMMAND_VAL (PCI_FBTEN | PCI_SERREN | PCI_PERREN | PCI_MWIEN |\ - PCI_BMEN | PCI_MEMEN | PCI_IOEN) - -/* PCI_STATUS 16 bit Status */ -#define PCI_PERR BIT_15S /* Parity Error */ -#define PCI_SERR BIT_14S /* Signaled SERR */ -#define PCI_RMABORT BIT_13S /* Received Master Abort */ -#define PCI_RTABORT BIT_12S /* Received Target Abort */ - /* Bit 11: reserved */ -#define PCI_DEVSEL (3<<9) /* Bit 10.. 9: DEVSEL Timing */ -#define PCI_DEV_FAST (0<<9) /* fast */ -#define PCI_DEV_MEDIUM (1<<9) /* medium */ -#define PCI_DEV_SLOW (2<<9) /* slow */ -#define PCI_DATAPERR BIT_8S /* DATA Parity error detected */ -#define PCI_FB2BCAP BIT_7S /* Fast Back-to-Back Capability */ -#define PCI_UDF BIT_6S /* User Defined Features */ -#define PCI_66MHZCAP BIT_5S /* 66 MHz PCI bus clock capable */ -#define PCI_NEWCAP BIT_4S /* New cap. list implemented */ -#define PCI_INT_STAT BIT_3S /* Interrupt INTx# Status (PCI 2.3) */ - /* Bit 2.. 0: reserved */ - -#define PCI_ERRBITS (PCI_PERR | PCI_SERR | PCI_RMABORT | PCI_RTABORT |\ - PCI_DATAPERR) - -/* PCI_CLASS_CODE 24 bit Class Code */ -/* Byte 2: Base Class (02) */ -/* Byte 1: SubClass (00) */ -/* Byte 0: Programming Interface (00) */ - -/* PCI_CACHE_LSZ 8 bit Cache Line Size */ -/* Possible values: 0,2,4,8,16,32,64,128 */ - -/* PCI_HEADER_T 8 bit Header Type */ -#define PCI_HD_MF_DEV BIT_7S /* 0= single, 1= multi-func dev */ -#define PCI_HD_TYPE 0x7f /* Bit 6..0: Header Layout 0= normal */ - -/* PCI_BIST 8 bit Built-in selftest */ -/* Built-in Self test not supported (optional) */ - -/* PCI_BASE_1ST 32 bit 1st Base address */ -#define PCI_MEMSIZE 0x4000L /* use 16 kB Memory Base */ -#define PCI_MEMBASE_MSK 0xffffc000L /* Bit 31..14: Memory Base Address */ -#define PCI_MEMSIZE_MSK 0x00003ff0L /* Bit 13.. 4: Memory Size Req. */ -#define PCI_PREFEN BIT_3 /* Prefetchable */ -#define PCI_MEM_TYP (3L<<2) /* Bit 2.. 1: Memory Type */ -#define PCI_MEM32BIT (0L<<1) /* Base addr anywhere in 32 Bit range */ -#define PCI_MEM1M (1L<<1) /* Base addr below 1 MegaByte */ -#define PCI_MEM64BIT (2L<<1) /* Base addr anywhere in 64 Bit range */ -#define PCI_MEMSPACE BIT_0 /* Memory Space Indicator */ - -/* PCI_BASE_2ND 32 bit 2nd Base address */ -#define PCI_IOBASE 0xffffff00L /* Bit 31.. 8: I/O Base address */ -#define PCI_IOSIZE 0x000000fcL /* Bit 7.. 2: I/O Size Requirements */ - /* Bit 1: reserved */ -#define PCI_IOSPACE BIT_0 /* I/O Space Indicator */ - -/* PCI_BASE_ROM 32 bit Expansion ROM Base Address */ -#define PCI_ROMBASE_MSK 0xfffe0000L /* Bit 31..17: ROM Base address */ -#define PCI_ROMBASE_SIZ (0x1cL<<14) /* Bit 16..14: Treat as Base or Size */ -#define PCI_ROMSIZE (0x38L<<11) /* Bit 13..11: ROM Size Requirements */ - /* Bit 10.. 1: reserved */ -#define PCI_ROMEN BIT_0 /* Address Decode enable */ - -/* Device Dependent Region */ -/* PCI_OUR_REG_1 32 bit Our Register 1 */ - /* Bit 31..29: reserved */ -#define PCI_PHY_COMA BIT_28 /* Set PHY to Coma Mode (YUKON only) */ -#define PCI_TEST_CAL BIT_27 /* Test PCI buffer calib. (YUKON only) */ -#define PCI_EN_CAL BIT_26 /* Enable PCI buffer calib. (YUKON only) */ -#define PCI_VIO BIT_25 /* PCI I/O Voltage, 0 = 3.3V, 1 = 5V */ -#define PCI_DIS_BOOT BIT_24 /* Disable BOOT via ROM */ -#define PCI_EN_IO BIT_23 /* Mapping to I/O space */ -#define PCI_EN_FPROM BIT_22 /* Enable FLASH mapping to memory */ - /* 1 = Map Flash to memory */ - /* 0 = Disable addr. dec */ -#define PCI_PAGESIZE (3L<<20) /* Bit 21..20: FLASH Page Size */ -#define PCI_PAGE_16 (0L<<20) /* 16 k pages */ -#define PCI_PAGE_32K (1L<<20) /* 32 k pages */ -#define PCI_PAGE_64K (2L<<20) /* 64 k pages */ -#define PCI_PAGE_128K (3L<<20) /* 128 k pages */ - /* Bit 19: reserved */ -#define PCI_PAGEREG (7L<<16) /* Bit 18..16: Page Register */ -#define PCI_NOTAR BIT_15 /* No turnaround cycle */ -#define PCI_FORCE_BE BIT_14 /* Assert all BEs on MR */ -#define PCI_DIS_MRL BIT_13 /* Disable Mem Read Line */ -#define PCI_DIS_MRM BIT_12 /* Disable Mem Read Multiple */ -#define PCI_DIS_MWI BIT_11 /* Disable Mem Write & Invalidate */ -#define PCI_DISC_CLS BIT_10 /* Disc: cacheLsz bound */ -#define PCI_BURST_DIS BIT_9 /* Burst Disable */ -#define PCI_DIS_PCI_CLK BIT_8 /* Disable PCI clock driving */ -#define PCI_SKEW_DAS (0xfL<<4) /* Bit 7.. 4: Skew Ctrl, DAS Ext */ -#define PCI_SKEW_BASE 0xfL /* Bit 3.. 0: Skew Ctrl, Base */ - - -/* PCI_OUR_REG_2 32 bit Our Register 2 */ -#define PCI_VPD_WR_THR (0xffL<<24) /* Bit 31..24: VPD Write Threshold */ -#define PCI_DEV_SEL (0x7fL<<17) /* Bit 23..17: EEPROM Device Select */ -#define PCI_VPD_ROM_SZ (7L<<14) /* Bit 16..14: VPD ROM Size */ - /* Bit 13..12: reserved */ -#define PCI_PATCH_DIR (0xfL<<8) /* Bit 11.. 8: Ext Patches dir 3..0 */ -#define PCI_PATCH_DIR_3 BIT_11 -#define PCI_PATCH_DIR_2 BIT_10 -#define PCI_PATCH_DIR_1 BIT_9 -#define PCI_PATCH_DIR_0 BIT_8 -#define PCI_EXT_PATCHS (0xfL<<4) /* Bit 7.. 4: Extended Patches 3..0 */ -#define PCI_EXT_PATCH_3 BIT_7 -#define PCI_EXT_PATCH_2 BIT_6 -#define PCI_EXT_PATCH_1 BIT_5 -#define PCI_EXT_PATCH_0 BIT_4 -#define PCI_EN_DUMMY_RD BIT_3 /* Enable Dummy Read */ -#define PCI_REV_DESC BIT_2 /* Reverse Desc. Bytes */ - /* Bit 1: reserved */ -#define PCI_USEDATA64 BIT_0 /* Use 64Bit Data bus ext */ - - -/* Power Management Region */ -/* PCI_PM_CAP_REG 16 bit Power Management Capabilities */ -#define PCI_PME_SUP_MSK (0x1f<<11) /* Bit 15..11: PM Event Support Mask */ -#define PCI_PME_D3C_SUP BIT_15S /* PME from D3cold Support (if Vaux) */ -#define PCI_PME_D3H_SUP BIT_14S /* PME from D3hot Support */ -#define PCI_PME_D2_SUP BIT_13S /* PME from D2 Support */ -#define PCI_PME_D1_SUP BIT_12S /* PME from D1 Support */ -#define PCI_PME_D0_SUP BIT_11S /* PME from D0 Support */ -#define PCI_PM_D2_SUP BIT_10S /* D2 Support in 33 MHz mode */ -#define PCI_PM_D1_SUP BIT_9S /* D1 Support */ - /* Bit 8.. 6: reserved */ -#define PCI_PM_DSI BIT_5S /* Device Specific Initialization */ -#define PCI_PM_APS BIT_4S /* Auxialiary Power Source */ -#define PCI_PME_CLOCK BIT_3S /* PM Event Clock */ -#define PCI_PM_VER_MSK 7 /* Bit 2.. 0: PM PCI Spec. version */ - -/* PCI_PM_CTL_STS 16 bit Power Management Control/Status */ -#define PCI_PME_STATUS BIT_15S /* PME Status (YUKON only) */ -#define PCI_PM_DAT_SCL (3<<13) /* Bit 14..13: Data Reg. scaling factor */ -#define PCI_PM_DAT_SEL (0xf<<9) /* Bit 12.. 9: PM data selector field */ -#define PCI_PME_EN BIT_8S /* Enable PME# generation (YUKON only) */ - /* Bit 7.. 2: reserved */ -#define PCI_PM_STATE_MSK 3 /* Bit 1.. 0: Power Management State */ - -#define PCI_PM_STATE_D0 0 /* D0: Operational (default) */ -#define PCI_PM_STATE_D1 1 /* D1: (YUKON only) */ -#define PCI_PM_STATE_D2 2 /* D2: (YUKON only) */ -#define PCI_PM_STATE_D3 3 /* D3: HOT, Power Down and Reset */ - -/* VPD Region */ -/* PCI_VPD_ADR_REG 16 bit VPD Address Register */ -#define PCI_VPD_FLAG BIT_15S /* starts VPD rd/wr cycle */ -#define PCI_VPD_ADR_MSK 0x7fffL /* Bit 14.. 0: VPD address mask */ - -/* Control Register File (Address Map) */ - -/* - * Bank 0 - */ -#define B0_RAP 0x0000 /* 8 bit Register Address Port */ - /* 0x0001 - 0x0003: reserved */ -#define B0_CTST 0x0004 /* 16 bit Control/Status register */ -#define B0_LED 0x0006 /* 8 Bit LED register */ -#define B0_POWER_CTRL 0x0007 /* 8 Bit Power Control reg (YUKON only) */ -#define B0_ISRC 0x0008 /* 32 bit Interrupt Source Register */ -#define B0_IMSK 0x000c /* 32 bit Interrupt Mask Register */ -#define B0_HWE_ISRC 0x0010 /* 32 bit HW Error Interrupt Src Reg */ -#define B0_HWE_IMSK 0x0014 /* 32 bit HW Error Interrupt Mask Reg */ -#define B0_SP_ISRC 0x0018 /* 32 bit Special Interrupt Source Reg */ - /* 0x001c: reserved */ - -/* B0 XMAC 1 registers (GENESIS only) */ -#define B0_XM1_IMSK 0x0020 /* 16 bit r/w XMAC 1 Interrupt Mask Register*/ - /* 0x0022 - 0x0027: reserved */ -#define B0_XM1_ISRC 0x0028 /* 16 bit ro XMAC 1 Interrupt Status Reg */ - /* 0x002a - 0x002f: reserved */ -#define B0_XM1_PHY_ADDR 0x0030 /* 16 bit r/w XMAC 1 PHY Address Register */ - /* 0x0032 - 0x0033: reserved */ -#define B0_XM1_PHY_DATA 0x0034 /* 16 bit r/w XMAC 1 PHY Data Register */ - /* 0x0036 - 0x003f: reserved */ - -/* B0 XMAC 2 registers (GENESIS only) */ -#define B0_XM2_IMSK 0x0040 /* 16 bit r/w XMAC 2 Interrupt Mask Register*/ - /* 0x0042 - 0x0047: reserved */ -#define B0_XM2_ISRC 0x0048 /* 16 bit ro XMAC 2 Interrupt Status Reg */ - /* 0x004a - 0x004f: reserved */ -#define B0_XM2_PHY_ADDR 0x0050 /* 16 bit r/w XMAC 2 PHY Address Register */ - /* 0x0052 - 0x0053: reserved */ -#define B0_XM2_PHY_DATA 0x0054 /* 16 bit r/w XMAC 2 PHY Data Register */ - /* 0x0056 - 0x005f: reserved */ - -/* BMU Control Status Registers */ -#define B0_R1_CSR 0x0060 /* 32 bit BMU Ctrl/Stat Rx Queue 1 */ -#define B0_R2_CSR 0x0064 /* 32 bit BMU Ctrl/Stat Rx Queue 2 */ -#define B0_XS1_CSR 0x0068 /* 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */ -#define B0_XA1_CSR 0x006c /* 32 bit BMU Ctrl/Stat Async Tx Queue 1*/ -#define B0_XS2_CSR 0x0070 /* 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */ -#define B0_XA2_CSR 0x0074 /* 32 bit BMU Ctrl/Stat Async Tx Queue 2*/ - /* 0x0078 - 0x007f: reserved */ - -/* - * Bank 1 - * - completely empty (this is the RAP Block window) - * Note: if RAP = 1 this page is reserved - */ - -/* - * Bank 2 - */ -/* NA reg = 48 bit Network Address Register, 3x16 or 8x8 bit readable */ -#define B2_MAC_1 0x0100 /* NA reg MAC Address 1 */ - /* 0x0106 - 0x0107: reserved */ -#define B2_MAC_2 0x0108 /* NA reg MAC Address 2 */ - /* 0x010e - 0x010f: reserved */ -#define B2_MAC_3 0x0110 /* NA reg MAC Address 3 */ - /* 0x0116 - 0x0117: reserved */ -#define B2_CONN_TYP 0x0118 /* 8 bit Connector type */ -#define B2_PMD_TYP 0x0119 /* 8 bit PMD type */ -#define B2_MAC_CFG 0x011a /* 8 bit MAC Configuration / Chip Revision */ -#define B2_CHIP_ID 0x011b /* 8 bit Chip Identification Number */ - /* Eprom registers are currently of no use */ -#define B2_E_0 0x011c /* 8 bit EPROM Byte 0 (ext. SRAM size */ -#define B2_E_1 0x011d /* 8 bit EPROM Byte 1 (PHY type) */ -#define B2_E_2 0x011e /* 8 bit EPROM Byte 2 */ -#define B2_E_3 0x011f /* 8 bit EPROM Byte 3 */ -#define B2_FAR 0x0120 /* 32 bit Flash-Prom Addr Reg/Cnt */ -#define B2_FDP 0x0124 /* 8 bit Flash-Prom Data Port */ - /* 0x0125 - 0x0127: reserved */ -#define B2_LD_CTRL 0x0128 /* 8 bit EPROM loader control register */ -#define B2_LD_TEST 0x0129 /* 8 bit EPROM loader test register */ - /* 0x012a - 0x012f: reserved */ -#define B2_TI_INI 0x0130 /* 32 bit Timer Init Value */ -#define B2_TI_VAL 0x0134 /* 32 bit Timer Value */ -#define B2_TI_CTRL 0x0138 /* 8 bit Timer Control */ -#define B2_TI_TEST 0x0139 /* 8 Bit Timer Test */ - /* 0x013a - 0x013f: reserved */ -#define B2_IRQM_INI 0x0140 /* 32 bit IRQ Moderation Timer Init Reg.*/ -#define B2_IRQM_VAL 0x0144 /* 32 bit IRQ Moderation Timer Value */ -#define B2_IRQM_CTRL 0x0148 /* 8 bit IRQ Moderation Timer Control */ -#define B2_IRQM_TEST 0x0149 /* 8 bit IRQ Moderation Timer Test */ -#define B2_IRQM_MSK 0x014c /* 32 bit IRQ Moderation Mask */ -#define B2_IRQM_HWE_MSK 0x0150 /* 32 bit IRQ Moderation HW Error Mask */ - /* 0x0154 - 0x0157: reserved */ -#define B2_TST_CTRL1 0x0158 /* 8 bit Test Control Register 1 */ -#define B2_TST_CTRL2 0x0159 /* 8 bit Test Control Register 2 */ - /* 0x015a - 0x015b: reserved */ -#define B2_GP_IO 0x015c /* 32 bit General Purpose I/O Register */ -#define B2_I2C_CTRL 0x0160 /* 32 bit I2C HW Control Register */ -#define B2_I2C_DATA 0x0164 /* 32 bit I2C HW Data Register */ -#define B2_I2C_IRQ 0x0168 /* 32 bit I2C HW IRQ Register */ -#define B2_I2C_SW 0x016c /* 32 bit I2C SW Port Register */ - -/* Blink Source Counter (GENESIS only) */ -#define B2_BSC_INI 0x0170 /* 32 bit Blink Source Counter Init Val */ -#define B2_BSC_VAL 0x0174 /* 32 bit Blink Source Counter Value */ -#define B2_BSC_CTRL 0x0178 /* 8 bit Blink Source Counter Control */ -#define B2_BSC_STAT 0x0179 /* 8 bit Blink Source Counter Status */ -#define B2_BSC_TST 0x017a /* 16 bit Blink Source Counter Test Reg */ - /* 0x017c - 0x017f: reserved */ - -/* - * Bank 3 - */ -/* RAM Random Registers */ -#define B3_RAM_ADDR 0x0180 /* 32 bit RAM Address, to read or write */ -#define B3_RAM_DATA_LO 0x0184 /* 32 bit RAM Data Word (low dWord) */ -#define B3_RAM_DATA_HI 0x0188 /* 32 bit RAM Data Word (high dWord) */ - /* 0x018c - 0x018f: reserved */ - -/* RAM Interface Registers */ -/* - * The HW-Spec. calls this registers Timeout Value 0..11. But this names are - * not usable in SW. Please notice these are NOT real timeouts, these are - * the number of qWords transferred continuously. - */ -#define B3_RI_WTO_R1 0x0190 /* 8 bit WR Timeout Queue R1 (TO0) */ -#define B3_RI_WTO_XA1 0x0191 /* 8 bit WR Timeout Queue XA1 (TO1) */ -#define B3_RI_WTO_XS1 0x0192 /* 8 bit WR Timeout Queue XS1 (TO2) */ -#define B3_RI_RTO_R1 0x0193 /* 8 bit RD Timeout Queue R1 (TO3) */ -#define B3_RI_RTO_XA1 0x0194 /* 8 bit RD Timeout Queue XA1 (TO4) */ -#define B3_RI_RTO_XS1 0x0195 /* 8 bit RD Timeout Queue XS1 (TO5) */ -#define B3_RI_WTO_R2 0x0196 /* 8 bit WR Timeout Queue R2 (TO6) */ -#define B3_RI_WTO_XA2 0x0197 /* 8 bit WR Timeout Queue XA2 (TO7) */ -#define B3_RI_WTO_XS2 0x0198 /* 8 bit WR Timeout Queue XS2 (TO8) */ -#define B3_RI_RTO_R2 0x0199 /* 8 bit RD Timeout Queue R2 (TO9) */ -#define B3_RI_RTO_XA2 0x019a /* 8 bit RD Timeout Queue XA2 (TO10)*/ -#define B3_RI_RTO_XS2 0x019b /* 8 bit RD Timeout Queue XS2 (TO11)*/ -#define B3_RI_TO_VAL 0x019c /* 8 bit Current Timeout Count Val */ - /* 0x019d - 0x019f: reserved */ -#define B3_RI_CTRL 0x01a0 /* 16 bit RAM Interface Control Register */ -#define B3_RI_TEST 0x01a2 /* 8 bit RAM Interface Test Register */ - /* 0x01a3 - 0x01af: reserved */ - -/* MAC Arbiter Registers (GENESIS only) */ -/* these are the no. of qWord transferred continuously and NOT real timeouts */ -#define B3_MA_TOINI_RX1 0x01b0 /* 8 bit Timeout Init Val Rx Path MAC 1 */ -#define B3_MA_TOINI_RX2 0x01b1 /* 8 bit Timeout Init Val Rx Path MAC 2 */ -#define B3_MA_TOINI_TX1 0x01b2 /* 8 bit Timeout Init Val Tx Path MAC 1 */ -#define B3_MA_TOINI_TX2 0x01b3 /* 8 bit Timeout Init Val Tx Path MAC 2 */ -#define B3_MA_TOVAL_RX1 0x01b4 /* 8 bit Timeout Value Rx Path MAC 1 */ -#define B3_MA_TOVAL_RX2 0x01b5 /* 8 bit Timeout Value Rx Path MAC 1 */ -#define B3_MA_TOVAL_TX1 0x01b6 /* 8 bit Timeout Value Tx Path MAC 2 */ -#define B3_MA_TOVAL_TX2 0x01b7 /* 8 bit Timeout Value Tx Path MAC 2 */ -#define B3_MA_TO_CTRL 0x01b8 /* 16 bit MAC Arbiter Timeout Ctrl Reg */ -#define B3_MA_TO_TEST 0x01ba /* 16 bit MAC Arbiter Timeout Test Reg */ - /* 0x01bc - 0x01bf: reserved */ -#define B3_MA_RCINI_RX1 0x01c0 /* 8 bit Recovery Init Val Rx Path MAC 1 */ -#define B3_MA_RCINI_RX2 0x01c1 /* 8 bit Recovery Init Val Rx Path MAC 2 */ -#define B3_MA_RCINI_TX1 0x01c2 /* 8 bit Recovery Init Val Tx Path MAC 1 */ -#define B3_MA_RCINI_TX2 0x01c3 /* 8 bit Recovery Init Val Tx Path MAC 2 */ -#define B3_MA_RCVAL_RX1 0x01c4 /* 8 bit Recovery Value Rx Path MAC 1 */ -#define B3_MA_RCVAL_RX2 0x01c5 /* 8 bit Recovery Value Rx Path MAC 1 */ -#define B3_MA_RCVAL_TX1 0x01c6 /* 8 bit Recovery Value Tx Path MAC 2 */ -#define B3_MA_RCVAL_TX2 0x01c7 /* 8 bit Recovery Value Tx Path MAC 2 */ -#define B3_MA_RC_CTRL 0x01c8 /* 16 bit MAC Arbiter Recovery Ctrl Reg */ -#define B3_MA_RC_TEST 0x01ca /* 16 bit MAC Arbiter Recovery Test Reg */ - /* 0x01cc - 0x01cf: reserved */ - -/* Packet Arbiter Registers (GENESIS only) */ -/* these are real timeouts */ -#define B3_PA_TOINI_RX1 0x01d0 /* 16 bit Timeout Init Val Rx Path MAC 1 */ - /* 0x01d2 - 0x01d3: reserved */ -#define B3_PA_TOINI_RX2 0x01d4 /* 16 bit Timeout Init Val Rx Path MAC 2 */ - /* 0x01d6 - 0x01d7: reserved */ -#define B3_PA_TOINI_TX1 0x01d8 /* 16 bit Timeout Init Val Tx Path MAC 1 */ - /* 0x01da - 0x01db: reserved */ -#define B3_PA_TOINI_TX2 0x01dc /* 16 bit Timeout Init Val Tx Path MAC 2 */ - /* 0x01de - 0x01df: reserved */ -#define B3_PA_TOVAL_RX1 0x01e0 /* 16 bit Timeout Val Rx Path MAC 1 */ - /* 0x01e2 - 0x01e3: reserved */ -#define B3_PA_TOVAL_RX2 0x01e4 /* 16 bit Timeout Val Rx Path MAC 2 */ - /* 0x01e6 - 0x01e7: reserved */ -#define B3_PA_TOVAL_TX1 0x01e8 /* 16 bit Timeout Val Tx Path MAC 1 */ - /* 0x01ea - 0x01eb: reserved */ -#define B3_PA_TOVAL_TX2 0x01ec /* 16 bit Timeout Val Tx Path MAC 2 */ - /* 0x01ee - 0x01ef: reserved */ -#define B3_PA_CTRL 0x01f0 /* 16 bit Packet Arbiter Ctrl Register */ -#define B3_PA_TEST 0x01f2 /* 16 bit Packet Arbiter Test Register */ - /* 0x01f4 - 0x01ff: reserved */ - -/* - * Bank 4 - 5 - */ -/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */ -#define TXA_ITI_INI 0x0200 /* 32 bit Tx Arb Interval Timer Init Val*/ -#define TXA_ITI_VAL 0x0204 /* 32 bit Tx Arb Interval Timer Value */ -#define TXA_LIM_INI 0x0208 /* 32 bit Tx Arb Limit Counter Init Val */ -#define TXA_LIM_VAL 0x020c /* 32 bit Tx Arb Limit Counter Value */ -#define TXA_CTRL 0x0210 /* 8 bit Tx Arbiter Control Register */ -#define TXA_TEST 0x0211 /* 8 bit Tx Arbiter Test Register */ -#define TXA_STAT 0x0212 /* 8 bit Tx Arbiter Status Register */ - /* 0x0213 - 0x027f: reserved */ - /* 0x0280 - 0x0292: MAC 2 */ - /* 0x0213 - 0x027f: reserved */ - -/* - * Bank 6 - */ -/* External registers (GENESIS only) */ -#define B6_EXT_REG 0x0300 - -/* - * Bank 7 - */ -/* This is a copy of the Configuration register file (lower half) */ -#define B7_CFG_SPC 0x0380 - -/* - * Bank 8 - 15 - */ -/* Receive and Transmit Queue Registers, use Q_ADDR() to access */ -#define B8_Q_REGS 0x0400 - -/* Queue Register Offsets, use Q_ADDR() to access */ -#define Q_D 0x00 /* 8*32 bit Current Descriptor */ -#define Q_DA_L 0x20 /* 32 bit Current Descriptor Address Low dWord */ -#define Q_DA_H 0x24 /* 32 bit Current Descriptor Address High dWord */ -#define Q_AC_L 0x28 /* 32 bit Current Address Counter Low dWord */ -#define Q_AC_H 0x2c /* 32 bit Current Address Counter High dWord */ -#define Q_BC 0x30 /* 32 bit Current Byte Counter */ -#define Q_CSR 0x34 /* 32 bit BMU Control/Status Register */ -#define Q_F 0x38 /* 32 bit Flag Register */ -#define Q_T1 0x3c /* 32 bit Test Register 1 */ -#define Q_T1_TR 0x3c /* 8 bit Test Register 1 Transfer SM */ -#define Q_T1_WR 0x3d /* 8 bit Test Register 1 Write Descriptor SM */ -#define Q_T1_RD 0x3e /* 8 bit Test Register 1 Read Descriptor SM */ -#define Q_T1_SV 0x3f /* 8 bit Test Register 1 Supervisor SM */ -#define Q_T2 0x40 /* 32 bit Test Register 2 */ -#define Q_T3 0x44 /* 32 bit Test Register 3 */ - /* 0x48 - 0x7f: reserved */ - -/* - * Bank 16 - 23 - */ -/* RAM Buffer Registers */ -#define B16_RAM_REGS 0x0800 - -/* RAM Buffer Register Offsets, use RB_ADDR() to access */ -#define RB_START 0x00 /* 32 bit RAM Buffer Start Address */ -#define RB_END 0x04 /* 32 bit RAM Buffer End Address */ -#define RB_WP 0x08 /* 32 bit RAM Buffer Write Pointer */ -#define RB_RP 0x0c /* 32 bit RAM Buffer Read Pointer */ -#define RB_RX_UTPP 0x10 /* 32 bit Rx Upper Threshold, Pause Pack */ -#define RB_RX_LTPP 0x14 /* 32 bit Rx Lower Threshold, Pause Pack */ -#define RB_RX_UTHP 0x18 /* 32 bit Rx Upper Threshold, High Prio */ -#define RB_RX_LTHP 0x1c /* 32 bit Rx Lower Threshold, High Prio */ - /* 0x10 - 0x1f: reserved at Tx RAM Buffer Registers */ -#define RB_PC 0x20 /* 32 bit RAM Buffer Packet Counter */ -#define RB_LEV 0x24 /* 32 bit RAM Buffer Level Register */ -#define RB_CTRL 0x28 /* 8 bit RAM Buffer Control Register */ -#define RB_TST1 0x29 /* 8 bit RAM Buffer Test Register 1 */ -#define RB_TST2 0x2A /* 8 bit RAM Buffer Test Register 2 */ - /* 0x2c - 0x7f: reserved */ - -/* - * Bank 24 - */ -/* - * Receive MAC FIFO, Receive LED, and Link_Sync regs (GENESIS only) - * use MR_ADDR() to access - */ -#define RX_MFF_EA 0x0c00 /* 32 bit Receive MAC FIFO End Address */ -#define RX_MFF_WP 0x0c04 /* 32 bit Receive MAC FIFO Write Pointer */ - /* 0x0c08 - 0x0c0b: reserved */ -#define RX_MFF_RP 0x0c0c /* 32 bit Receive MAC FIFO Read Pointer */ -#define RX_MFF_PC 0x0c10 /* 32 bit Receive MAC FIFO Packet Cnt */ -#define RX_MFF_LEV 0x0c14 /* 32 bit Receive MAC FIFO Level */ -#define RX_MFF_CTRL1 0x0c18 /* 16 bit Receive MAC FIFO Control Reg 1*/ -#define RX_MFF_STAT_TO 0x0c1a /* 8 bit Receive MAC Status Timeout */ -#define RX_MFF_TIST_TO 0x0c1b /* 8 bit Receive MAC Time Stamp Timeout */ -#define RX_MFF_CTRL2 0x0c1c /* 8 bit Receive MAC FIFO Control Reg 2*/ -#define RX_MFF_TST1 0x0c1d /* 8 bit Receive MAC FIFO Test Reg 1 */ -#define RX_MFF_TST2 0x0c1e /* 8 bit Receive MAC FIFO Test Reg 2 */ - /* 0x0c1f: reserved */ -#define RX_LED_INI 0x0c20 /* 32 bit Receive LED Cnt Init Value */ -#define RX_LED_VAL 0x0c24 /* 32 bit Receive LED Cnt Current Value */ -#define RX_LED_CTRL 0x0c28 /* 8 bit Receive LED Cnt Control Reg */ -#define RX_LED_TST 0x0c29 /* 8 bit Receive LED Cnt Test Register */ - /* 0x0c2a - 0x0c2f: reserved */ -#define LNK_SYNC_INI 0x0c30 /* 32 bit Link Sync Cnt Init Value */ -#define LNK_SYNC_VAL 0x0c34 /* 32 bit Link Sync Cnt Current Value */ -#define LNK_SYNC_CTRL 0x0c38 /* 8 bit Link Sync Cnt Control Register */ -#define LNK_SYNC_TST 0x0c39 /* 8 bit Link Sync Cnt Test Register */ - /* 0x0c3a - 0x0c3b: reserved */ -#define LNK_LED_REG 0x0c3c /* 8 bit Link LED Register */ - /* 0x0c3d - 0x0c3f: reserved */ - -/* Receive GMAC FIFO (YUKON only), use MR_ADDR() to access */ -#define RX_GMF_EA 0x0c40 /* 32 bit Rx GMAC FIFO End Address */ -#define RX_GMF_AF_THR 0x0c44 /* 32 bit Rx GMAC FIFO Almost Full Thresh. */ -#define RX_GMF_CTRL_T 0x0c48 /* 32 bit Rx GMAC FIFO Control/Test */ -#define RX_GMF_FL_MSK 0x0c4c /* 32 bit Rx GMAC FIFO Flush Mask */ -#define RX_GMF_FL_THR 0x0c50 /* 32 bit Rx GMAC FIFO Flush Threshold */ - /* 0x0c54 - 0x0c5f: reserved */ -#define RX_GMF_WP 0x0c60 /* 32 bit Rx GMAC FIFO Write Pointer */ - /* 0x0c64 - 0x0c67: reserved */ -#define RX_GMF_WLEV 0x0c68 /* 32 bit Rx GMAC FIFO Write Level */ - /* 0x0c6c - 0x0c6f: reserved */ -#define RX_GMF_RP 0x0c70 /* 32 bit Rx GMAC FIFO Read Pointer */ - /* 0x0c74 - 0x0c77: reserved */ -#define RX_GMF_RLEV 0x0c78 /* 32 bit Rx GMAC FIFO Read Level */ - /* 0x0c7c - 0x0c7f: reserved */ - -/* - * Bank 25 - */ - /* 0x0c80 - 0x0cbf: MAC 2 */ - /* 0x0cc0 - 0x0cff: reserved */ - -/* - * Bank 26 - */ -/* - * Transmit MAC FIFO and Transmit LED Registers (GENESIS only), - * use MR_ADDR() to access - */ -#define TX_MFF_EA 0x0d00 /* 32 bit Transmit MAC FIFO End Address */ -#define TX_MFF_WP 0x0d04 /* 32 bit Transmit MAC FIFO WR Pointer */ -#define TX_MFF_WSP 0x0d08 /* 32 bit Transmit MAC FIFO WR Shadow Ptr */ -#define TX_MFF_RP 0x0d0c /* 32 bit Transmit MAC FIFO RD Pointer */ -#define TX_MFF_PC 0x0d10 /* 32 bit Transmit MAC FIFO Packet Cnt */ -#define TX_MFF_LEV 0x0d14 /* 32 bit Transmit MAC FIFO Level */ -#define TX_MFF_CTRL1 0x0d18 /* 16 bit Transmit MAC FIFO Ctrl Reg 1 */ -#define TX_MFF_WAF 0x0d1a /* 8 bit Transmit MAC Wait after flush */ - /* 0x0c1b: reserved */ -#define TX_MFF_CTRL2 0x0d1c /* 8 bit Transmit MAC FIFO Ctrl Reg 2 */ -#define TX_MFF_TST1 0x0d1d /* 8 bit Transmit MAC FIFO Test Reg 1 */ -#define TX_MFF_TST2 0x0d1e /* 8 bit Transmit MAC FIFO Test Reg 2 */ - /* 0x0d1f: reserved */ -#define TX_LED_INI 0x0d20 /* 32 bit Transmit LED Cnt Init Value */ -#define TX_LED_VAL 0x0d24 /* 32 bit Transmit LED Cnt Current Val */ -#define TX_LED_CTRL 0x0d28 /* 8 bit Transmit LED Cnt Control Reg */ -#define TX_LED_TST 0x0d29 /* 8 bit Transmit LED Cnt Test Reg */ - /* 0x0d2a - 0x0d3f: reserved */ - -/* Transmit GMAC FIFO (YUKON only), use MR_ADDR() to access */ -#define TX_GMF_EA 0x0d40 /* 32 bit Tx GMAC FIFO End Address */ -#define TX_GMF_AE_THR 0x0d44 /* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/ -#define TX_GMF_CTRL_T 0x0d48 /* 32 bit Tx GMAC FIFO Control/Test */ - /* 0x0d4c - 0x0d5f: reserved */ -#define TX_GMF_WP 0x0d60 /* 32 bit Tx GMAC FIFO Write Pointer */ -#define TX_GMF_WSP 0x0d64 /* 32 bit Tx GMAC FIFO Write Shadow Ptr. */ -#define TX_GMF_WLEV 0x0d68 /* 32 bit Tx GMAC FIFO Write Level */ - /* 0x0d6c - 0x0d6f: reserved */ -#define TX_GMF_RP 0x0d70 /* 32 bit Tx GMAC FIFO Read Pointer */ -#define TX_GMF_RSTP 0x0d74 /* 32 bit Tx GMAC FIFO Restart Pointer */ -#define TX_GMF_RLEV 0x0d78 /* 32 bit Tx GMAC FIFO Read Level */ - /* 0x0d7c - 0x0d7f: reserved */ - -/* - * Bank 27 - */ - /* 0x0d80 - 0x0dbf: MAC 2 */ - /* 0x0daa - 0x0dff: reserved */ - -/* - * Bank 28 - */ -/* Descriptor Poll Timer Registers */ -#define B28_DPT_INI 0x0e00 /* 24 bit Descriptor Poll Timer Init Val */ -#define B28_DPT_VAL 0x0e04 /* 24 bit Descriptor Poll Timer Curr Val */ -#define B28_DPT_CTRL 0x0e08 /* 8 bit Descriptor Poll Timer Ctrl Reg */ - /* 0x0e09: reserved */ -#define B28_DPT_TST 0x0e0a /* 8 bit Descriptor Poll Timer Test Reg */ - /* 0x0e0b: reserved */ - -/* Time Stamp Timer Registers (YUKON only) */ - /* 0x0e10: reserved */ -#define GMAC_TI_ST_VAL 0x0e14 /* 32 bit Time Stamp Timer Curr Val */ -#define GMAC_TI_ST_CTRL 0x0e18 /* 8 bit Time Stamp Timer Ctrl Reg */ - /* 0x0e19: reserved */ -#define GMAC_TI_ST_TST 0x0e1a /* 8 bit Time Stamp Timer Test Reg */ - /* 0x0e1b - 0x0e7f: reserved */ - -/* - * Bank 29 - */ - /* 0x0e80 - 0x0efc: reserved */ - -/* - * Bank 30 - */ -/* GMAC and GPHY Control Registers (YUKON only) */ -#define GMAC_CTRL 0x0f00 /* 32 bit GMAC Control Reg */ -#define GPHY_CTRL 0x0f04 /* 32 bit GPHY Control Reg */ -#define GMAC_IRQ_SRC 0x0f08 /* 8 bit GMAC Interrupt Source Reg */ - /* 0x0f09 - 0x0f0b: reserved */ -#define GMAC_IRQ_MSK 0x0f0c /* 8 bit GMAC Interrupt Mask Reg */ - /* 0x0f0d - 0x0f0f: reserved */ -#define GMAC_LINK_CTRL 0x0f10 /* 16 bit Link Control Reg */ - /* 0x0f14 - 0x0f1f: reserved */ - -/* Wake-up Frame Pattern Match Control Registers (YUKON only) */ - -#define WOL_REG_OFFS 0x20 /* HW-Bug: Address is + 0x20 against spec. */ - -#define WOL_CTRL_STAT 0x0f20 /* 16 bit WOL Control/Status Reg */ -#define WOL_MATCH_CTL 0x0f22 /* 8 bit WOL Match Control Reg */ -#define WOL_MATCH_RES 0x0f23 /* 8 bit WOL Match Result Reg */ -#define WOL_MAC_ADDR_LO 0x0f24 /* 32 bit WOL MAC Address Low */ -#define WOL_MAC_ADDR_HI 0x0f28 /* 16 bit WOL MAC Address High */ -#define WOL_PATT_RPTR 0x0f2c /* 8 bit WOL Pattern Read Ptr */ - -/* use this macro to access above registers */ -#define WOL_REG(Reg) ((Reg) + (pAC->GIni.GIWolOffs)) - - -/* WOL Pattern Length Registers (YUKON only) */ - -#define WOL_PATT_LEN_LO 0x0f30 /* 32 bit WOL Pattern Length 3..0 */ -#define WOL_PATT_LEN_HI 0x0f34 /* 24 bit WOL Pattern Length 6..4 */ - -/* WOL Pattern Counter Registers (YUKON only) */ - -#define WOL_PATT_CNT_0 0x0f38 /* 32 bit WOL Pattern Counter 3..0 */ -#define WOL_PATT_CNT_4 0x0f3c /* 24 bit WOL Pattern Counter 6..4 */ - /* 0x0f40 - 0x0f7f: reserved */ - -/* - * Bank 31 - */ -/* 0x0f80 - 0x0fff: reserved */ - -/* - * Bank 32 - 33 - */ -#define WOL_PATT_RAM_1 0x1000 /* WOL Pattern RAM Link 1 */ - -/* - * Bank 0x22 - 0x3f - */ -/* 0x1100 - 0x1fff: reserved */ - -/* - * Bank 0x40 - 0x4f - */ -#define BASE_XMAC_1 0x2000 /* XMAC 1 registers */ - -/* - * Bank 0x50 - 0x5f - */ - -#define BASE_GMAC_1 0x2800 /* GMAC 1 registers */ - -/* - * Bank 0x60 - 0x6f - */ -#define BASE_XMAC_2 0x3000 /* XMAC 2 registers */ - -/* - * Bank 0x70 - 0x7f - */ -#define BASE_GMAC_2 0x3800 /* GMAC 2 registers */ - -/* - * Control Register Bit Definitions: - */ -/* B0_RAP 8 bit Register Address Port */ - /* Bit 7: reserved */ -#define RAP_RAP 0x3f /* Bit 6..0: 0 = block 0,..,6f = block 6f */ - -/* B0_CTST 16 bit Control/Status register */ - /* Bit 15..14: reserved */ -#define CS_CLK_RUN_HOT BIT_13S /* CLK_RUN hot m. (YUKON-Lite only) */ -#define CS_CLK_RUN_RST BIT_12S /* CLK_RUN reset (YUKON-Lite only) */ -#define CS_CLK_RUN_ENA BIT_11S /* CLK_RUN enable (YUKON-Lite only) */ -#define CS_VAUX_AVAIL BIT_10S /* VAUX available (YUKON only) */ -#define CS_BUS_CLOCK BIT_9S /* Bus Clock 0/1 = 33/66 MHz */ -#define CS_BUS_SLOT_SZ BIT_8S /* Slot Size 0/1 = 32/64 bit slot */ -#define CS_ST_SW_IRQ BIT_7S /* Set IRQ SW Request */ -#define CS_CL_SW_IRQ BIT_6S /* Clear IRQ SW Request */ -#define CS_STOP_DONE BIT_5S /* Stop Master is finished */ -#define CS_STOP_MAST BIT_4S /* Command Bit to stop the master */ -#define CS_MRST_CLR BIT_3S /* Clear Master reset */ -#define CS_MRST_SET BIT_2S /* Set Master reset */ -#define CS_RST_CLR BIT_1S /* Clear Software reset */ -#define CS_RST_SET BIT_0S /* Set Software reset */ - -/* B0_LED 8 Bit LED register */ - /* Bit 7.. 2: reserved */ -#define LED_STAT_ON BIT_1S /* Status LED on */ -#define LED_STAT_OFF BIT_0S /* Status LED off */ - -/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */ -#define PC_VAUX_ENA BIT_7 /* Switch VAUX Enable */ -#define PC_VAUX_DIS BIT_6 /* Switch VAUX Disable */ -#define PC_VCC_ENA BIT_5 /* Switch VCC Enable */ -#define PC_VCC_DIS BIT_4 /* Switch VCC Disable */ -#define PC_VAUX_ON BIT_3 /* Switch VAUX On */ -#define PC_VAUX_OFF BIT_2 /* Switch VAUX Off */ -#define PC_VCC_ON BIT_1 /* Switch VCC On */ -#define PC_VCC_OFF BIT_0 /* Switch VCC Off */ - -/* B0_ISRC 32 bit Interrupt Source Register */ -/* B0_IMSK 32 bit Interrupt Mask Register */ -/* B0_SP_ISRC 32 bit Special Interrupt Source Reg */ -/* B2_IRQM_MSK 32 bit IRQ Moderation Mask */ -#define IS_ALL_MSK 0xbfffffffUL /* All Interrupt bits */ -#define IS_HW_ERR BIT_31 /* Interrupt HW Error */ - /* Bit 30: reserved */ -#define IS_PA_TO_RX1 BIT_29 /* Packet Arb Timeout Rx1 */ -#define IS_PA_TO_RX2 BIT_28 /* Packet Arb Timeout Rx2 */ -#define IS_PA_TO_TX1 BIT_27 /* Packet Arb Timeout Tx1 */ -#define IS_PA_TO_TX2 BIT_26 /* Packet Arb Timeout Tx2 */ -#define IS_I2C_READY BIT_25 /* IRQ on end of I2C Tx */ -#define IS_IRQ_SW BIT_24 /* SW forced IRQ */ -#define IS_EXT_REG BIT_23 /* IRQ from LM80 or PHY (GENESIS only) */ - /* IRQ from PHY (YUKON only) */ -#define IS_TIMINT BIT_22 /* IRQ from Timer */ -#define IS_MAC1 BIT_21 /* IRQ from MAC 1 */ -#define IS_LNK_SYNC_M1 BIT_20 /* Link Sync Cnt wrap MAC 1 */ -#define IS_MAC2 BIT_19 /* IRQ from MAC 2 */ -#define IS_LNK_SYNC_M2 BIT_18 /* Link Sync Cnt wrap MAC 2 */ -/* Receive Queue 1 */ -#define IS_R1_B BIT_17 /* Q_R1 End of Buffer */ -#define IS_R1_F BIT_16 /* Q_R1 End of Frame */ -#define IS_R1_C BIT_15 /* Q_R1 Encoding Error */ -/* Receive Queue 2 */ -#define IS_R2_B BIT_14 /* Q_R2 End of Buffer */ -#define IS_R2_F BIT_13 /* Q_R2 End of Frame */ -#define IS_R2_C BIT_12 /* Q_R2 Encoding Error */ -/* Synchronous Transmit Queue 1 */ -#define IS_XS1_B BIT_11 /* Q_XS1 End of Buffer */ -#define IS_XS1_F BIT_10 /* Q_XS1 End of Frame */ -#define IS_XS1_C BIT_9 /* Q_XS1 Encoding Error */ -/* Asynchronous Transmit Queue 1 */ -#define IS_XA1_B BIT_8 /* Q_XA1 End of Buffer */ -#define IS_XA1_F BIT_7 /* Q_XA1 End of Frame */ -#define IS_XA1_C BIT_6 /* Q_XA1 Encoding Error */ -/* Synchronous Transmit Queue 2 */ -#define IS_XS2_B BIT_5 /* Q_XS2 End of Buffer */ -#define IS_XS2_F BIT_4 /* Q_XS2 End of Frame */ -#define IS_XS2_C BIT_3 /* Q_XS2 Encoding Error */ -/* Asynchronous Transmit Queue 2 */ -#define IS_XA2_B BIT_2 /* Q_XA2 End of Buffer */ -#define IS_XA2_F BIT_1 /* Q_XA2 End of Frame */ -#define IS_XA2_C BIT_0 /* Q_XA2 Encoding Error */ - - -/* B0_HWE_ISRC 32 bit HW Error Interrupt Src Reg */ -/* B0_HWE_IMSK 32 bit HW Error Interrupt Mask Reg */ -/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */ -#define IS_ERR_MSK 0x00000fffL /* All Error bits */ - /* Bit 31..14: reserved */ -#define IS_IRQ_TIST_OV BIT_13 /* Time Stamp Timer Overflow (YUKON only) */ -#define IS_IRQ_SENSOR BIT_12 /* IRQ from Sensor (YUKON only) */ -#define IS_IRQ_MST_ERR BIT_11 /* IRQ master error detected */ -#define IS_IRQ_STAT BIT_10 /* IRQ status exception */ -#define IS_NO_STAT_M1 BIT_9 /* No Rx Status from MAC 1 */ -#define IS_NO_STAT_M2 BIT_8 /* No Rx Status from MAC 2 */ -#define IS_NO_TIST_M1 BIT_7 /* No Time Stamp from MAC 1 */ -#define IS_NO_TIST_M2 BIT_6 /* No Time Stamp from MAC 2 */ -#define IS_RAM_RD_PAR BIT_5 /* RAM Read Parity Error */ -#define IS_RAM_WR_PAR BIT_4 /* RAM Write Parity Error */ -#define IS_M1_PAR_ERR BIT_3 /* MAC 1 Parity Error */ -#define IS_M2_PAR_ERR BIT_2 /* MAC 2 Parity Error */ -#define IS_R1_PAR_ERR BIT_1 /* Queue R1 Parity Error */ -#define IS_R2_PAR_ERR BIT_0 /* Queue R2 Parity Error */ - -/* B2_CONN_TYP 8 bit Connector type */ -/* B2_PMD_TYP 8 bit PMD type */ -/* Values of connector and PMD type comply to SysKonnect internal std */ - -/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */ -#define CFG_CHIP_R_MSK (0xf<<4) /* Bit 7.. 4: Chip Revision */ - /* Bit 3.. 2: reserved */ -#define CFG_DIS_M2_CLK BIT_1S /* Disable Clock for 2nd MAC */ -#define CFG_SNG_MAC BIT_0S /* MAC Config: 0=2 MACs / 1=1 MAC*/ - -/* B2_CHIP_ID 8 bit Chip Identification Number */ -#define CHIP_ID_GENESIS 0x0a /* Chip ID for GENESIS */ -#define CHIP_ID_YUKON 0xb0 /* Chip ID for YUKON */ -#define CHIP_ID_YUKON_LITE 0xb1 /* Chip ID for YUKON-Lite (Rev. A1-A3) */ -#define CHIP_ID_YUKON_LP 0xb2 /* Chip ID for YUKON-LP */ - -#define CHIP_REV_YU_LITE_A1 3 /* Chip Rev. for YUKON-Lite A1,A2 */ -#define CHIP_REV_YU_LITE_A3 7 /* Chip Rev. for YUKON-Lite A3 */ - -/* B2_FAR 32 bit Flash-Prom Addr Reg/Cnt */ -#define FAR_ADDR 0x1ffffL /* Bit 16.. 0: FPROM Address mask */ - -/* B2_LD_CTRL 8 bit EPROM loader control register */ -/* Bits are currently reserved */ - -/* B2_LD_TEST 8 bit EPROM loader test register */ - /* Bit 7.. 4: reserved */ -#define LD_T_ON BIT_3S /* Loader Test mode on */ -#define LD_T_OFF BIT_2S /* Loader Test mode off */ -#define LD_T_STEP BIT_1S /* Decrement FPROM addr. Counter */ -#define LD_START BIT_0S /* Start loading FPROM */ - -/* - * Timer Section - */ -/* B2_TI_CTRL 8 bit Timer control */ -/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */ - /* Bit 7.. 3: reserved */ -#define TIM_START BIT_2S /* Start Timer */ -#define TIM_STOP BIT_1S /* Stop Timer */ -#define TIM_CLR_IRQ BIT_0S /* Clear Timer IRQ (!IRQM) */ - -/* B2_TI_TEST 8 Bit Timer Test */ -/* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */ -/* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */ - /* Bit 7.. 3: reserved */ -#define TIM_T_ON BIT_2S /* Test mode on */ -#define TIM_T_OFF BIT_1S /* Test mode off */ -#define TIM_T_STEP BIT_0S /* Test step */ - -/* B28_DPT_INI 32 bit Descriptor Poll Timer Init Val */ -/* B28_DPT_VAL 32 bit Descriptor Poll Timer Curr Val */ - /* Bit 31..24: reserved */ -#define DPT_MSK 0x00ffffffL /* Bit 23.. 0: Desc Poll Timer Bits */ - -/* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */ - /* Bit 7.. 2: reserved */ -#define DPT_START BIT_1S /* Start Descriptor Poll Timer */ -#define DPT_STOP BIT_0S /* Stop Descriptor Poll Timer */ - -/* B2_E_3 8 bit lower 4 bits used for HW self test result */ -#define B2_E3_RES_MASK 0x0f - -/* B2_TST_CTRL1 8 bit Test Control Register 1 */ -#define TST_FRC_DPERR_MR BIT_7S /* force DATAPERR on MST RD */ -#define TST_FRC_DPERR_MW BIT_6S /* force DATAPERR on MST WR */ -#define TST_FRC_DPERR_TR BIT_5S /* force DATAPERR on TRG RD */ -#define TST_FRC_DPERR_TW BIT_4S /* force DATAPERR on TRG WR */ -#define TST_FRC_APERR_M BIT_3S /* force ADDRPERR on MST */ -#define TST_FRC_APERR_T BIT_2S /* force ADDRPERR on TRG */ -#define TST_CFG_WRITE_ON BIT_1S /* Enable Config Reg WR */ -#define TST_CFG_WRITE_OFF BIT_0S /* Disable Config Reg WR */ - -/* B2_TST_CTRL2 8 bit Test Control Register 2 */ - /* Bit 7.. 4: reserved */ - /* force the following error on the next master read/write */ -#define TST_FRC_DPERR_MR64 BIT_3S /* DataPERR RD 64 */ -#define TST_FRC_DPERR_MW64 BIT_2S /* DataPERR WR 64 */ -#define TST_FRC_APERR_1M64 BIT_1S /* AddrPERR on 1. phase */ -#define TST_FRC_APERR_2M64 BIT_0S /* AddrPERR on 2. phase */ - -/* B2_GP_IO 32 bit General Purpose I/O Register */ - /* Bit 31..26: reserved */ -#define GP_DIR_9 BIT_25 /* IO_9 direct, 0=In/1=Out */ -#define GP_DIR_8 BIT_24 /* IO_8 direct, 0=In/1=Out */ -#define GP_DIR_7 BIT_23 /* IO_7 direct, 0=In/1=Out */ -#define GP_DIR_6 BIT_22 /* IO_6 direct, 0=In/1=Out */ -#define GP_DIR_5 BIT_21 /* IO_5 direct, 0=In/1=Out */ -#define GP_DIR_4 BIT_20 /* IO_4 direct, 0=In/1=Out */ -#define GP_DIR_3 BIT_19 /* IO_3 direct, 0=In/1=Out */ -#define GP_DIR_2 BIT_18 /* IO_2 direct, 0=In/1=Out */ -#define GP_DIR_1 BIT_17 /* IO_1 direct, 0=In/1=Out */ -#define GP_DIR_0 BIT_16 /* IO_0 direct, 0=In/1=Out */ - /* Bit 15..10: reserved */ -#define GP_IO_9 BIT_9 /* IO_9 pin */ -#define GP_IO_8 BIT_8 /* IO_8 pin */ -#define GP_IO_7 BIT_7 /* IO_7 pin */ -#define GP_IO_6 BIT_6 /* IO_6 pin */ -#define GP_IO_5 BIT_5 /* IO_5 pin */ -#define GP_IO_4 BIT_4 /* IO_4 pin */ -#define GP_IO_3 BIT_3 /* IO_3 pin */ -#define GP_IO_2 BIT_2 /* IO_2 pin */ -#define GP_IO_1 BIT_1 /* IO_1 pin */ -#define GP_IO_0 BIT_0 /* IO_0 pin */ - -/* B2_I2C_CTRL 32 bit I2C HW Control Register */ -#define I2C_FLAG BIT_31 /* Start read/write if WR */ -#define I2C_ADDR (0x7fffL<<16) /* Bit 30..16: Addr to be RD/WR */ -#define I2C_DEV_SEL (0x7fL<<9) /* Bit 15.. 9: I2C Device Select */ - /* Bit 8.. 5: reserved */ -#define I2C_BURST_LEN BIT_4 /* Burst Len, 1/4 bytes */ -#define I2C_DEV_SIZE (7<<1) /* Bit 3.. 1: I2C Device Size */ -#define I2C_025K_DEV (0<<1) /* 0: 256 Bytes or smal. */ -#define I2C_05K_DEV (1<<1) /* 1: 512 Bytes */ -#define I2C_1K_DEV (2<<1) /* 2: 1024 Bytes */ -#define I2C_2K_DEV (3<<1) /* 3: 2048 Bytes */ -#define I2C_4K_DEV (4<<1) /* 4: 4096 Bytes */ -#define I2C_8K_DEV (5<<1) /* 5: 8192 Bytes */ -#define I2C_16K_DEV (6<<1) /* 6: 16384 Bytes */ -#define I2C_32K_DEV (7<<1) /* 7: 32768 Bytes */ -#define I2C_STOP BIT_0 /* Interrupt I2C transfer */ - -/* B2_I2C_IRQ 32 bit I2C HW IRQ Register */ - /* Bit 31.. 1 reserved */ -#define I2C_CLR_IRQ BIT_0 /* Clear I2C IRQ */ - -/* B2_I2C_SW 32 bit (8 bit access) I2C HW SW Port Register */ - /* Bit 7.. 3: reserved */ -#define I2C_DATA_DIR BIT_2S /* direction of I2C_DATA */ -#define I2C_DATA BIT_1S /* I2C Data Port */ -#define I2C_CLK BIT_0S /* I2C Clock Port */ - -/* - * I2C Address - */ -#define I2C_SENS_ADDR LM80_ADDR /* I2C Sensor Address, (Volt and Temp)*/ - - -/* B2_BSC_CTRL 8 bit Blink Source Counter Control */ - /* Bit 7.. 2: reserved */ -#define BSC_START BIT_1S /* Start Blink Source Counter */ -#define BSC_STOP BIT_0S /* Stop Blink Source Counter */ - -/* B2_BSC_STAT 8 bit Blink Source Counter Status */ - /* Bit 7.. 1: reserved */ -#define BSC_SRC BIT_0S /* Blink Source, 0=Off / 1=On */ - -/* B2_BSC_TST 16 bit Blink Source Counter Test Reg */ -#define BSC_T_ON BIT_2S /* Test mode on */ -#define BSC_T_OFF BIT_1S /* Test mode off */ -#define BSC_T_STEP BIT_0S /* Test step */ - - -/* B3_RAM_ADDR 32 bit RAM Address, to read or write */ - /* Bit 31..19: reserved */ -#define RAM_ADR_RAN 0x0007ffffL /* Bit 18.. 0: RAM Address Range */ - -/* RAM Interface Registers */ -/* B3_RI_CTRL 16 bit RAM Iface Control Register */ - /* Bit 15..10: reserved */ -#define RI_CLR_RD_PERR BIT_9S /* Clear IRQ RAM Read Parity Err */ -#define RI_CLR_WR_PERR BIT_8S /* Clear IRQ RAM Write Parity Err*/ - /* Bit 7.. 2: reserved */ -#define RI_RST_CLR BIT_1S /* Clear RAM Interface Reset */ -#define RI_RST_SET BIT_0S /* Set RAM Interface Reset */ - -/* B3_RI_TEST 8 bit RAM Iface Test Register */ - /* Bit 15.. 4: reserved */ -#define RI_T_EV BIT_3S /* Timeout Event occured */ -#define RI_T_ON BIT_2S /* Timeout Timer Test On */ -#define RI_T_OFF BIT_1S /* Timeout Timer Test Off */ -#define RI_T_STEP BIT_0S /* Timeout Timer Step */ - -/* MAC Arbiter Registers */ -/* B3_MA_TO_CTRL 16 bit MAC Arbiter Timeout Ctrl Reg */ - /* Bit 15.. 4: reserved */ -#define MA_FOE_ON BIT_3S /* XMAC Fast Output Enable ON */ -#define MA_FOE_OFF BIT_2S /* XMAC Fast Output Enable OFF */ -#define MA_RST_CLR BIT_1S /* Clear MAC Arbiter Reset */ -#define MA_RST_SET BIT_0S /* Set MAC Arbiter Reset */ - -/* B3_MA_RC_CTRL 16 bit MAC Arbiter Recovery Ctrl Reg */ - /* Bit 15.. 8: reserved */ -#define MA_ENA_REC_TX2 BIT_7S /* Enable Recovery Timer TX2 */ -#define MA_DIS_REC_TX2 BIT_6S /* Disable Recovery Timer TX2 */ -#define MA_ENA_REC_TX1 BIT_5S /* Enable Recovery Timer TX1 */ -#define MA_DIS_REC_TX1 BIT_4S /* Disable Recovery Timer TX1 */ -#define MA_ENA_REC_RX2 BIT_3S /* Enable Recovery Timer RX2 */ -#define MA_DIS_REC_RX2 BIT_2S /* Disable Recovery Timer RX2 */ -#define MA_ENA_REC_RX1 BIT_1S /* Enable Recovery Timer RX1 */ -#define MA_DIS_REC_RX1 BIT_0S /* Disable Recovery Timer RX1 */ - -/* Packet Arbiter Registers */ -/* B3_PA_CTRL 16 bit Packet Arbiter Ctrl Register */ - /* Bit 15..14: reserved */ -#define PA_CLR_TO_TX2 BIT_13S /* Clear IRQ Packet Timeout TX2 */ -#define PA_CLR_TO_TX1 BIT_12S /* Clear IRQ Packet Timeout TX1 */ -#define PA_CLR_TO_RX2 BIT_11S /* Clear IRQ Packet Timeout RX2 */ -#define PA_CLR_TO_RX1 BIT_10S /* Clear IRQ Packet Timeout RX1 */ -#define PA_ENA_TO_TX2 BIT_9S /* Enable Timeout Timer TX2 */ -#define PA_DIS_TO_TX2 BIT_8S /* Disable Timeout Timer TX2 */ -#define PA_ENA_TO_TX1 BIT_7S /* Enable Timeout Timer TX1 */ -#define PA_DIS_TO_TX1 BIT_6S /* Disable Timeout Timer TX1 */ -#define PA_ENA_TO_RX2 BIT_5S /* Enable Timeout Timer RX2 */ -#define PA_DIS_TO_RX2 BIT_4S /* Disable Timeout Timer RX2 */ -#define PA_ENA_TO_RX1 BIT_3S /* Enable Timeout Timer RX1 */ -#define PA_DIS_TO_RX1 BIT_2S /* Disable Timeout Timer RX1 */ -#define PA_RST_CLR BIT_1S /* Clear MAC Arbiter Reset */ -#define PA_RST_SET BIT_0S /* Set MAC Arbiter Reset */ - -#define PA_ENA_TO_ALL (PA_ENA_TO_RX1 | PA_ENA_TO_RX2 |\ - PA_ENA_TO_TX1 | PA_ENA_TO_TX2) - -/* Rx/Tx Path related Arbiter Test Registers */ -/* B3_MA_TO_TEST 16 bit MAC Arbiter Timeout Test Reg */ -/* B3_MA_RC_TEST 16 bit MAC Arbiter Recovery Test Reg */ -/* B3_PA_TEST 16 bit Packet Arbiter Test Register */ -/* Bit 15, 11, 7, and 3 are reserved in B3_PA_TEST */ -#define TX2_T_EV BIT_15S /* TX2 Timeout/Recv Event occured */ -#define TX2_T_ON BIT_14S /* TX2 Timeout/Recv Timer Test On */ -#define TX2_T_OFF BIT_13S /* TX2 Timeout/Recv Timer Tst Off */ -#define TX2_T_STEP BIT_12S /* TX2 Timeout/Recv Timer Step */ -#define TX1_T_EV BIT_11S /* TX1 Timeout/Recv Event occured */ -#define TX1_T_ON BIT_10S /* TX1 Timeout/Recv Timer Test On */ -#define TX1_T_OFF BIT_9S /* TX1 Timeout/Recv Timer Tst Off */ -#define TX1_T_STEP BIT_8S /* TX1 Timeout/Recv Timer Step */ -#define RX2_T_EV BIT_7S /* RX2 Timeout/Recv Event occured */ -#define RX2_T_ON BIT_6S /* RX2 Timeout/Recv Timer Test On */ -#define RX2_T_OFF BIT_5S /* RX2 Timeout/Recv Timer Tst Off */ -#define RX2_T_STEP BIT_4S /* RX2 Timeout/Recv Timer Step */ -#define RX1_T_EV BIT_3S /* RX1 Timeout/Recv Event occured */ -#define RX1_T_ON BIT_2S /* RX1 Timeout/Recv Timer Test On */ -#define RX1_T_OFF BIT_1S /* RX1 Timeout/Recv Timer Tst Off */ -#define RX1_T_STEP BIT_0S /* RX1 Timeout/Recv Timer Step */ - - -/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */ -/* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */ -/* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */ -/* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */ -/* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */ - /* Bit 31..24: reserved */ -#define TXA_MAX_VAL 0x00ffffffUL/* Bit 23.. 0: Max TXA Timer/Cnt Val */ - -/* TXA_CTRL 8 bit Tx Arbiter Control Register */ -#define TXA_ENA_FSYNC BIT_7S /* Enable force of sync Tx queue */ -#define TXA_DIS_FSYNC BIT_6S /* Disable force of sync Tx queue */ -#define TXA_ENA_ALLOC BIT_5S /* Enable alloc of free bandwidth */ -#define TXA_DIS_ALLOC BIT_4S /* Disable alloc of free bandwidth */ -#define TXA_START_RC BIT_3S /* Start sync Rate Control */ -#define TXA_STOP_RC BIT_2S /* Stop sync Rate Control */ -#define TXA_ENA_ARB BIT_1S /* Enable Tx Arbiter */ -#define TXA_DIS_ARB BIT_0S /* Disable Tx Arbiter */ - -/* TXA_TEST 8 bit Tx Arbiter Test Register */ - /* Bit 7.. 6: reserved */ -#define TXA_INT_T_ON BIT_5S /* Tx Arb Interval Timer Test On */ -#define TXA_INT_T_OFF BIT_4S /* Tx Arb Interval Timer Test Off */ -#define TXA_INT_T_STEP BIT_3S /* Tx Arb Interval Timer Step */ -#define TXA_LIM_T_ON BIT_2S /* Tx Arb Limit Timer Test On */ -#define TXA_LIM_T_OFF BIT_1S /* Tx Arb Limit Timer Test Off */ -#define TXA_LIM_T_STEP BIT_0S /* Tx Arb Limit Timer Step */ - -/* TXA_STAT 8 bit Tx Arbiter Status Register */ - /* Bit 7.. 1: reserved */ -#define TXA_PRIO_XS BIT_0S /* sync queue has prio to send */ - -/* Q_BC 32 bit Current Byte Counter */ - /* Bit 31..16: reserved */ -#define BC_MAX 0xffff /* Bit 15.. 0: Byte counter */ - -/* BMU Control Status Registers */ -/* B0_R1_CSR 32 bit BMU Ctrl/Stat Rx Queue 1 */ -/* B0_R2_CSR 32 bit BMU Ctrl/Stat Rx Queue 2 */ -/* B0_XA1_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 1 */ -/* B0_XS1_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 1 */ -/* B0_XA2_CSR 32 bit BMU Ctrl/Stat Sync Tx Queue 2 */ -/* B0_XS2_CSR 32 bit BMU Ctrl/Stat Async Tx Queue 2 */ -/* Q_CSR 32 bit BMU Control/Status Register */ - /* Bit 31..25: reserved */ -#define CSR_SV_IDLE BIT_24 /* BMU SM Idle */ - /* Bit 23..22: reserved */ -#define CSR_DESC_CLR BIT_21 /* Clear Reset for Descr */ -#define CSR_DESC_SET BIT_20 /* Set Reset for Descr */ -#define CSR_FIFO_CLR BIT_19 /* Clear Reset for FIFO */ -#define CSR_FIFO_SET BIT_18 /* Set Reset for FIFO */ -#define CSR_HPI_RUN BIT_17 /* Release HPI SM */ -#define CSR_HPI_RST BIT_16 /* Reset HPI SM to Idle */ -#define CSR_SV_RUN BIT_15 /* Release Supervisor SM */ -#define CSR_SV_RST BIT_14 /* Reset Supervisor SM */ -#define CSR_DREAD_RUN BIT_13 /* Release Descr Read SM */ -#define CSR_DREAD_RST BIT_12 /* Reset Descr Read SM */ -#define CSR_DWRITE_RUN BIT_11 /* Release Descr Write SM */ -#define CSR_DWRITE_RST BIT_10 /* Reset Descr Write SM */ -#define CSR_TRANS_RUN BIT_9 /* Release Transfer SM */ -#define CSR_TRANS_RST BIT_8 /* Reset Transfer SM */ -#define CSR_ENA_POL BIT_7 /* Enable Descr Polling */ -#define CSR_DIS_POL BIT_6 /* Disable Descr Polling */ -#define CSR_STOP BIT_5 /* Stop Rx/Tx Queue */ -#define CSR_START BIT_4 /* Start Rx/Tx Queue */ -#define CSR_IRQ_CL_P BIT_3 /* (Rx) Clear Parity IRQ */ -#define CSR_IRQ_CL_B BIT_2 /* Clear EOB IRQ */ -#define CSR_IRQ_CL_F BIT_1 /* Clear EOF IRQ */ -#define CSR_IRQ_CL_C BIT_0 /* Clear ERR IRQ */ - -#define CSR_SET_RESET (CSR_DESC_SET | CSR_FIFO_SET | CSR_HPI_RST |\ - CSR_SV_RST | CSR_DREAD_RST | CSR_DWRITE_RST |\ - CSR_TRANS_RST) -#define CSR_CLR_RESET (CSR_DESC_CLR | CSR_FIFO_CLR | CSR_HPI_RUN |\ - CSR_SV_RUN | CSR_DREAD_RUN | CSR_DWRITE_RUN |\ - CSR_TRANS_RUN) - -/* Q_F 32 bit Flag Register */ - /* Bit 31..28: reserved */ -#define F_ALM_FULL BIT_27 /* Rx FIFO: almost full */ -#define F_EMPTY BIT_27 /* Tx FIFO: empty flag */ -#define F_FIFO_EOF BIT_26 /* Tag (EOF Flag) bit in FIFO */ -#define F_WM_REACHED BIT_25 /* Watermark reached */ - /* reserved */ -#define F_FIFO_LEVEL (0x1fL<<16) /* Bit 23..16: # of Qwords in FIFO */ - /* Bit 15..11: reserved */ -#define F_WATER_MARK 0x0007ffL /* Bit 10.. 0: Watermark */ - -/* Q_T1 32 bit Test Register 1 */ -/* Holds four State Machine control Bytes */ -#define SM_CTRL_SV_MSK (0xffL<<24) /* Bit 31..24: Control Supervisor SM */ -#define SM_CTRL_RD_MSK (0xffL<<16) /* Bit 23..16: Control Read Desc SM */ -#define SM_CTRL_WR_MSK (0xffL<<8) /* Bit 15.. 8: Control Write Desc SM */ -#define SM_CTRL_TR_MSK 0xffL /* Bit 7.. 0: Control Transfer SM */ - -/* Q_T1_TR 8 bit Test Register 1 Transfer SM */ -/* Q_T1_WR 8 bit Test Register 1 Write Descriptor SM */ -/* Q_T1_RD 8 bit Test Register 1 Read Descriptor SM */ -/* Q_T1_SV 8 bit Test Register 1 Supervisor SM */ - -/* The control status byte of each machine looks like ... */ -#define SM_STATE 0xf0 /* Bit 7.. 4: State which shall be loaded */ -#define SM_LOAD BIT_3S /* Load the SM with SM_STATE */ -#define SM_TEST_ON BIT_2S /* Switch on SM Test Mode */ -#define SM_TEST_OFF BIT_1S /* Go off the Test Mode */ -#define SM_STEP BIT_0S /* Step the State Machine */ -/* The encoding of the states is not supported by the Diagnostics Tool */ - -/* Q_T2 32 bit Test Register 2 */ - /* Bit 31.. 8: reserved */ -#define T2_AC_T_ON BIT_7 /* Address Counter Test Mode on */ -#define T2_AC_T_OFF BIT_6 /* Address Counter Test Mode off */ -#define T2_BC_T_ON BIT_5 /* Byte Counter Test Mode on */ -#define T2_BC_T_OFF BIT_4 /* Byte Counter Test Mode off */ -#define T2_STEP04 BIT_3 /* Inc AC/Dec BC by 4 */ -#define T2_STEP03 BIT_2 /* Inc AC/Dec BC by 3 */ -#define T2_STEP02 BIT_1 /* Inc AC/Dec BC by 2 */ -#define T2_STEP01 BIT_0 /* Inc AC/Dec BC by 1 */ - -/* Q_T3 32 bit Test Register 3 */ - /* Bit 31.. 7: reserved */ -#define T3_MUX_MSK (7<<4) /* Bit 6.. 4: Mux Position */ - /* Bit 3: reserved */ -#define T3_VRAM_MSK 7 /* Bit 2.. 0: Virtual RAM Buffer Address */ - -/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */ -/* RB_START 32 bit RAM Buffer Start Address */ -/* RB_END 32 bit RAM Buffer End Address */ -/* RB_WP 32 bit RAM Buffer Write Pointer */ -/* RB_RP 32 bit RAM Buffer Read Pointer */ -/* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */ -/* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */ -/* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */ -/* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */ -/* RB_PC 32 bit RAM Buffer Packet Counter */ -/* RB_LEV 32 bit RAM Buffer Level Register */ - /* Bit 31..19: reserved */ -#define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */ - -/* RB_TST2 8 bit RAM Buffer Test Register 2 */ - /* Bit 7.. 4: reserved */ -#define RB_PC_DEC BIT_3S /* Packet Counter Decrem */ -#define RB_PC_T_ON BIT_2S /* Packet Counter Test On */ -#define RB_PC_T_OFF BIT_1S /* Packet Counter Tst Off */ -#define RB_PC_INC BIT_0S /* Packet Counter Increm */ - -/* RB_TST1 8 bit RAM Buffer Test Register 1 */ - /* Bit 7: reserved */ -#define RB_WP_T_ON BIT_6S /* Write Pointer Test On */ -#define RB_WP_T_OFF BIT_5S /* Write Pointer Test Off */ -#define RB_WP_INC BIT_4S /* Write Pointer Increm */ - /* Bit 3: reserved */ -#define RB_RP_T_ON BIT_2S /* Read Pointer Test On */ -#define RB_RP_T_OFF BIT_1S /* Read Pointer Test Off */ -#define RB_RP_DEC BIT_0S /* Read Pointer Decrement */ - -/* RB_CTRL 8 bit RAM Buffer Control Register */ - /* Bit 7.. 6: reserved */ -#define RB_ENA_STFWD BIT_5S /* Enable Store & Forward */ -#define RB_DIS_STFWD BIT_4S /* Disable Store & Forward */ -#define RB_ENA_OP_MD BIT_3S /* Enable Operation Mode */ -#define RB_DIS_OP_MD BIT_2S /* Disable Operation Mode */ -#define RB_RST_CLR BIT_1S /* Clear RAM Buf STM Reset */ -#define RB_RST_SET BIT_0S /* Set RAM Buf STM Reset */ - - -/* Receive and Transmit MAC FIFO Registers (GENESIS only) */ - -/* RX_MFF_EA 32 bit Receive MAC FIFO End Address */ -/* RX_MFF_WP 32 bit Receive MAC FIFO Write Pointer */ -/* RX_MFF_RP 32 bit Receive MAC FIFO Read Pointer */ -/* RX_MFF_PC 32 bit Receive MAC FIFO Packet Counter */ -/* RX_MFF_LEV 32 bit Receive MAC FIFO Level */ -/* TX_MFF_EA 32 bit Transmit MAC FIFO End Address */ -/* TX_MFF_WP 32 bit Transmit MAC FIFO Write Pointer */ -/* TX_MFF_WSP 32 bit Transmit MAC FIFO WR Shadow Pointer */ -/* TX_MFF_RP 32 bit Transmit MAC FIFO Read Pointer */ -/* TX_MFF_PC 32 bit Transmit MAC FIFO Packet Cnt */ -/* TX_MFF_LEV 32 bit Transmit MAC FIFO Level */ - /* Bit 31.. 6: reserved */ -#define MFF_MSK 0x007fL /* Bit 5.. 0: MAC FIFO Address/Ptr Bits */ - -/* RX_MFF_CTRL1 16 bit Receive MAC FIFO Control Reg 1 */ - /* Bit 15..14: reserved */ -#define MFF_ENA_RDY_PAT BIT_13S /* Enable Ready Patch */ -#define MFF_DIS_RDY_PAT BIT_12S /* Disable Ready Patch */ -#define MFF_ENA_TIM_PAT BIT_11S /* Enable Timing Patch */ -#define MFF_DIS_TIM_PAT BIT_10S /* Disable Timing Patch */ -#define MFF_ENA_ALM_FUL BIT_9S /* Enable AlmostFull Sign */ -#define MFF_DIS_ALM_FUL BIT_8S /* Disable AlmostFull Sign */ -#define MFF_ENA_PAUSE BIT_7S /* Enable Pause Signaling */ -#define MFF_DIS_PAUSE BIT_6S /* Disable Pause Signaling */ -#define MFF_ENA_FLUSH BIT_5S /* Enable Frame Flushing */ -#define MFF_DIS_FLUSH BIT_4S /* Disable Frame Flushing */ -#define MFF_ENA_TIST BIT_3S /* Enable Time Stamp Gener */ -#define MFF_DIS_TIST BIT_2S /* Disable Time Stamp Gener */ -#define MFF_CLR_INTIST BIT_1S /* Clear IRQ No Time Stamp */ -#define MFF_CLR_INSTAT BIT_0S /* Clear IRQ No Status */ - -#define MFF_RX_CTRL_DEF MFF_ENA_TIM_PAT - -/* TX_MFF_CTRL1 16 bit Transmit MAC FIFO Control Reg 1 */ -#define MFF_CLR_PERR BIT_15S /* Clear Parity Error IRQ */ - /* Bit 14: reserved */ -#define MFF_ENA_PKT_REC BIT_13S /* Enable Packet Recovery */ -#define MFF_DIS_PKT_REC BIT_12S /* Disable Packet Recovery */ -/* MFF_ENA_TIM_PAT (see RX_MFF_CTRL1) Bit 11: Enable Timing Patch */ -/* MFF_DIS_TIM_PAT (see RX_MFF_CTRL1) Bit 10: Disable Timing Patch */ -/* MFF_ENA_ALM_FUL (see RX_MFF_CTRL1) Bit 9: Enable Almost Full Sign */ -/* MFF_DIS_ALM_FUL (see RX_MFF_CTRL1) Bit 8: Disable Almost Full Sign */ -#define MFF_ENA_W4E BIT_7S /* Enable Wait for Empty */ -#define MFF_DIS_W4E BIT_6S /* Disable Wait for Empty */ -/* MFF_ENA_FLUSH (see RX_MFF_CTRL1) Bit 5: Enable Frame Flushing */ -/* MFF_DIS_FLUSH (see RX_MFF_CTRL1) Bit 4: Disable Frame Flushing */ -#define MFF_ENA_LOOPB BIT_3S /* Enable Loopback */ -#define MFF_DIS_LOOPB BIT_2S /* Disable Loopback */ -#define MFF_CLR_MAC_RST BIT_1S /* Clear XMAC Reset */ -#define MFF_SET_MAC_RST BIT_0S /* Set XMAC Reset */ - -#define MFF_TX_CTRL_DEF (MFF_ENA_PKT_REC | MFF_ENA_TIM_PAT | MFF_ENA_FLUSH) - -/* RX_MFF_TST2 8 bit Receive MAC FIFO Test Register 2 */ -/* TX_MFF_TST2 8 bit Transmit MAC FIFO Test Register 2 */ - /* Bit 7: reserved */ -#define MFF_WSP_T_ON BIT_6S /* Tx: Write Shadow Ptr TestOn */ -#define MFF_WSP_T_OFF BIT_5S /* Tx: Write Shadow Ptr TstOff */ -#define MFF_WSP_INC BIT_4S /* Tx: Write Shadow Ptr Increment */ -#define MFF_PC_DEC BIT_3S /* Packet Counter Decrement */ -#define MFF_PC_T_ON BIT_2S /* Packet Counter Test On */ -#define MFF_PC_T_OFF BIT_1S /* Packet Counter Test Off */ -#define MFF_PC_INC BIT_0S /* Packet Counter Increment */ - -/* RX_MFF_TST1 8 bit Receive MAC FIFO Test Register 1 */ -/* TX_MFF_TST1 8 bit Transmit MAC FIFO Test Register 1 */ - /* Bit 7: reserved */ -#define MFF_WP_T_ON BIT_6S /* Write Pointer Test On */ -#define MFF_WP_T_OFF BIT_5S /* Write Pointer Test Off */ -#define MFF_WP_INC BIT_4S /* Write Pointer Increm */ - /* Bit 3: reserved */ -#define MFF_RP_T_ON BIT_2S /* Read Pointer Test On */ -#define MFF_RP_T_OFF BIT_1S /* Read Pointer Test Off */ -#define MFF_RP_DEC BIT_0S /* Read Pointer Decrement */ - -/* RX_MFF_CTRL2 8 bit Receive MAC FIFO Control Reg 2 */ -/* TX_MFF_CTRL2 8 bit Transmit MAC FIFO Control Reg 2 */ - /* Bit 7..4: reserved */ -#define MFF_ENA_OP_MD BIT_3S /* Enable Operation Mode */ -#define MFF_DIS_OP_MD BIT_2S /* Disable Operation Mode */ -#define MFF_RST_CLR BIT_1S /* Clear MAC FIFO Reset */ -#define MFF_RST_SET BIT_0S /* Set MAC FIFO Reset */ - - -/* Link LED Counter Registers (GENESIS only) */ - -/* RX_LED_CTRL 8 bit Receive LED Cnt Control Reg */ -/* TX_LED_CTRL 8 bit Transmit LED Cnt Control Reg */ -/* LNK_SYNC_CTRL 8 bit Link Sync Cnt Control Register */ - /* Bit 7.. 3: reserved */ -#define LED_START BIT_2S /* Start Timer */ -#define LED_STOP BIT_1S /* Stop Timer */ -#define LED_STATE BIT_0S /* Rx/Tx: LED State, 1=LED on */ -#define LED_CLR_IRQ BIT_0S /* Lnk: Clear Link IRQ */ - -/* RX_LED_TST 8 bit Receive LED Cnt Test Register */ -/* TX_LED_TST 8 bit Transmit LED Cnt Test Register */ -/* LNK_SYNC_TST 8 bit Link Sync Cnt Test Register */ - /* Bit 7.. 3: reserved */ -#define LED_T_ON BIT_2S /* LED Counter Test mode On */ -#define LED_T_OFF BIT_1S /* LED Counter Test mode Off */ -#define LED_T_STEP BIT_0S /* LED Counter Step */ - -/* LNK_LED_REG 8 bit Link LED Register */ - /* Bit 7.. 6: reserved */ -#define LED_BLK_ON BIT_5S /* Link LED Blinking On */ -#define LED_BLK_OFF BIT_4S /* Link LED Blinking Off */ -#define LED_SYNC_ON BIT_3S /* Use Sync Wire to switch LED */ -#define LED_SYNC_OFF BIT_2S /* Disable Sync Wire Input */ -#define LED_ON BIT_1S /* switch LED on */ -#define LED_OFF BIT_0S /* switch LED off */ - -/* Receive and Transmit GMAC FIFO Registers (YUKON only) */ - -/* RX_GMF_EA 32 bit Rx GMAC FIFO End Address */ -/* RX_GMF_AF_THR 32 bit Rx GMAC FIFO Almost Full Thresh. */ -/* RX_GMF_WP 32 bit Rx GMAC FIFO Write Pointer */ -/* RX_GMF_WLEV 32 bit Rx GMAC FIFO Write Level */ -/* RX_GMF_RP 32 bit Rx GMAC FIFO Read Pointer */ -/* RX_GMF_RLEV 32 bit Rx GMAC FIFO Read Level */ -/* TX_GMF_EA 32 bit Tx GMAC FIFO End Address */ -/* TX_GMF_AE_THR 32 bit Tx GMAC FIFO Almost Empty Thresh.*/ -/* TX_GMF_WP 32 bit Tx GMAC FIFO Write Pointer */ -/* TX_GMF_WSP 32 bit Tx GMAC FIFO Write Shadow Ptr. */ -/* TX_GMF_WLEV 32 bit Tx GMAC FIFO Write Level */ -/* TX_GMF_RP 32 bit Tx GMAC FIFO Read Pointer */ -/* TX_GMF_RSTP 32 bit Tx GMAC FIFO Restart Pointer */ -/* TX_GMF_RLEV 32 bit Tx GMAC FIFO Read Level */ - -/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */ - /* Bits 31..15: reserved */ -#define GMF_WP_TST_ON BIT_14 /* Write Pointer Test On */ -#define GMF_WP_TST_OFF BIT_13 /* Write Pointer Test Off */ -#define GMF_WP_STEP BIT_12 /* Write Pointer Step/Increment */ - /* Bit 11: reserved */ -#define GMF_RP_TST_ON BIT_10 /* Read Pointer Test On */ -#define GMF_RP_TST_OFF BIT_9 /* Read Pointer Test Off */ -#define GMF_RP_STEP BIT_8 /* Read Pointer Step/Increment */ -#define GMF_RX_F_FL_ON BIT_7 /* Rx FIFO Flush Mode On */ -#define GMF_RX_F_FL_OFF BIT_6 /* Rx FIFO Flush Mode Off */ -#define GMF_CLI_RX_FO BIT_5 /* Clear IRQ Rx FIFO Overrun */ -#define GMF_CLI_RX_FC BIT_4 /* Clear IRQ Rx Frame Complete */ -#define GMF_OPER_ON BIT_3 /* Operational Mode On */ -#define GMF_OPER_OFF BIT_2 /* Operational Mode Off */ -#define GMF_RST_CLR BIT_1 /* Clear GMAC FIFO Reset */ -#define GMF_RST_SET BIT_0 /* Set GMAC FIFO Reset */ - -/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */ - /* Bits 31..19: reserved */ -#define GMF_WSP_TST_ON BIT_18 /* Write Shadow Pointer Test On */ -#define GMF_WSP_TST_OFF BIT_17 /* Write Shadow Pointer Test Off */ -#define GMF_WSP_STEP BIT_16 /* Write Shadow Pointer Step/Increment */ - /* Bits 15..7: same as for RX_GMF_CTRL_T */ -#define GMF_CLI_TX_FU BIT_6 /* Clear IRQ Tx FIFO Underrun */ -#define GMF_CLI_TX_FC BIT_5 /* Clear IRQ Tx Frame Complete */ -#define GMF_CLI_TX_PE BIT_4 /* Clear IRQ Tx Parity Error */ - /* Bits 3..0: same as for RX_GMF_CTRL_T */ - -#define GMF_RX_CTRL_DEF (GMF_OPER_ON | GMF_RX_F_FL_ON) -#define GMF_TX_CTRL_DEF GMF_OPER_ON - -#define RX_GMF_FL_THR_DEF 0x0a /* Rx GMAC FIFO Flush Threshold default */ - -/* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */ - /* Bit 7.. 3: reserved */ -#define GMT_ST_START BIT_2S /* Start Time Stamp Timer */ -#define GMT_ST_STOP BIT_1S /* Stop Time Stamp Timer */ -#define GMT_ST_CLR_IRQ BIT_0S /* Clear Time Stamp Timer IRQ */ - -/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */ - /* Bits 31.. 8: reserved */ -#define GMC_H_BURST_ON BIT_7 /* Half Duplex Burst Mode On */ -#define GMC_H_BURST_OFF BIT_6 /* Half Duplex Burst Mode Off */ -#define GMC_F_LOOPB_ON BIT_5 /* FIFO Loopback On */ -#define GMC_F_LOOPB_OFF BIT_4 /* FIFO Loopback Off */ -#define GMC_PAUSE_ON BIT_3 /* Pause On */ -#define GMC_PAUSE_OFF BIT_2 /* Pause Off */ -#define GMC_RST_CLR BIT_1 /* Clear GMAC Reset */ -#define GMC_RST_SET BIT_0 /* Set GMAC Reset */ - -/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */ - /* Bits 31..29: reserved */ -#define GPC_SEL_BDT BIT_28 /* Select Bi-Dir. Transfer for MDC/MDIO */ -#define GPC_INT_POL_HI BIT_27 /* IRQ Polarity is Active HIGH */ -#define GPC_75_OHM BIT_26 /* Use 75 Ohm Termination instead of 50 */ -#define GPC_DIS_FC BIT_25 /* Disable Automatic Fiber/Copper Detection */ -#define GPC_DIS_SLEEP BIT_24 /* Disable Energy Detect */ -#define GPC_HWCFG_M_3 BIT_23 /* HWCFG_MODE[3] */ -#define GPC_HWCFG_M_2 BIT_22 /* HWCFG_MODE[2] */ -#define GPC_HWCFG_M_1 BIT_21 /* HWCFG_MODE[1] */ -#define GPC_HWCFG_M_0 BIT_20 /* HWCFG_MODE[0] */ -#define GPC_ANEG_0 BIT_19 /* ANEG[0] */ -#define GPC_ENA_XC BIT_18 /* Enable MDI crossover */ -#define GPC_DIS_125 BIT_17 /* Disable 125 MHz clock */ -#define GPC_ANEG_3 BIT_16 /* ANEG[3] */ -#define GPC_ANEG_2 BIT_15 /* ANEG[2] */ -#define GPC_ANEG_1 BIT_14 /* ANEG[1] */ -#define GPC_ENA_PAUSE BIT_13 /* Enable Pause (SYM_OR_REM) */ -#define GPC_PHYADDR_4 BIT_12 /* Bit 4 of Phy Addr */ -#define GPC_PHYADDR_3 BIT_11 /* Bit 3 of Phy Addr */ -#define GPC_PHYADDR_2 BIT_10 /* Bit 2 of Phy Addr */ -#define GPC_PHYADDR_1 BIT_9 /* Bit 1 of Phy Addr */ -#define GPC_PHYADDR_0 BIT_8 /* Bit 0 of Phy Addr */ - /* Bits 7..2: reserved */ -#define GPC_RST_CLR BIT_1 /* Clear GPHY Reset */ -#define GPC_RST_SET BIT_0 /* Set GPHY Reset */ - -#define GPC_HWCFG_GMII_COP (GPC_HWCFG_M_3 | GPC_HWCFG_M_2 | \ - GPC_HWCFG_M_1 | GPC_HWCFG_M_0) - -#define GPC_HWCFG_GMII_FIB ( GPC_HWCFG_M_2 | \ - GPC_HWCFG_M_1 | GPC_HWCFG_M_0) - -#define GPC_ANEG_ADV_ALL_M (GPC_ANEG_3 | GPC_ANEG_2 | \ - GPC_ANEG_1 | GPC_ANEG_0) - -/* forced speed and duplex mode (don't mix with other ANEG bits) */ -#define GPC_FRC10MBIT_HALF 0 -#define GPC_FRC10MBIT_FULL GPC_ANEG_0 -#define GPC_FRC100MBIT_HALF GPC_ANEG_1 -#define GPC_FRC100MBIT_FULL (GPC_ANEG_0 | GPC_ANEG_1) - -/* auto-negotiation with limited advertised speeds */ -/* mix only with master/slave settings (for copper) */ -#define GPC_ADV_1000_HALF GPC_ANEG_2 -#define GPC_ADV_1000_FULL GPC_ANEG_3 -#define GPC_ADV_ALL (GPC_ANEG_2 | GPC_ANEG_3) - -/* master/slave settings */ -/* only for copper with 1000 Mbps */ -#define GPC_FORCE_MASTER 0 -#define GPC_FORCE_SLAVE GPC_ANEG_0 -#define GPC_PREF_MASTER GPC_ANEG_1 -#define GPC_PREF_SLAVE (GPC_ANEG_1 | GPC_ANEG_0) - -/* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */ -/* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */ -#define GM_IS_TX_CO_OV BIT_5 /* Transmit Counter Overflow IRQ */ -#define GM_IS_RX_CO_OV BIT_4 /* Receive Counter Overflow IRQ */ -#define GM_IS_TX_FF_UR BIT_3 /* Transmit FIFO Underrun */ -#define GM_IS_TX_COMPL BIT_2 /* Frame Transmission Complete */ -#define GM_IS_RX_FF_OR BIT_1 /* Receive FIFO Overrun */ -#define GM_IS_RX_COMPL BIT_0 /* Frame Reception Complete */ - -#define GMAC_DEF_MSK (GM_IS_TX_CO_OV | GM_IS_RX_CO_OV | \ - GM_IS_TX_FF_UR) - -/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */ - /* Bits 15.. 2: reserved */ -#define GMLC_RST_CLR BIT_1S /* Clear GMAC Link Reset */ -#define GMLC_RST_SET BIT_0S /* Set GMAC Link Reset */ - - -/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */ -#define WOL_CTL_LINK_CHG_OCC BIT_15S -#define WOL_CTL_MAGIC_PKT_OCC BIT_14S -#define WOL_CTL_PATTERN_OCC BIT_13S - -#define WOL_CTL_CLEAR_RESULT BIT_12S - -#define WOL_CTL_ENA_PME_ON_LINK_CHG BIT_11S -#define WOL_CTL_DIS_PME_ON_LINK_CHG BIT_10S -#define WOL_CTL_ENA_PME_ON_MAGIC_PKT BIT_9S -#define WOL_CTL_DIS_PME_ON_MAGIC_PKT BIT_8S -#define WOL_CTL_ENA_PME_ON_PATTERN BIT_7S -#define WOL_CTL_DIS_PME_ON_PATTERN BIT_6S - -#define WOL_CTL_ENA_LINK_CHG_UNIT BIT_5S -#define WOL_CTL_DIS_LINK_CHG_UNIT BIT_4S -#define WOL_CTL_ENA_MAGIC_PKT_UNIT BIT_3S -#define WOL_CTL_DIS_MAGIC_PKT_UNIT BIT_2S -#define WOL_CTL_ENA_PATTERN_UNIT BIT_1S -#define WOL_CTL_DIS_PATTERN_UNIT BIT_0S - -#define WOL_CTL_DEFAULT \ - (WOL_CTL_DIS_PME_ON_LINK_CHG | \ - WOL_CTL_DIS_PME_ON_PATTERN | \ - WOL_CTL_DIS_PME_ON_MAGIC_PKT | \ - WOL_CTL_DIS_LINK_CHG_UNIT | \ - WOL_CTL_DIS_PATTERN_UNIT | \ - WOL_CTL_DIS_MAGIC_PKT_UNIT) - -/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */ -#define WOL_CTL_PATT_ENA(x) (BIT_0 << (x)) - -#define SK_NUM_WOL_PATTERN 7 -#define SK_PATTERN_PER_WORD 4 -#define SK_BITMASK_PATTERN 7 -#define SK_POW_PATTERN_LENGTH 128 - -#define WOL_LENGTH_MSK 0x7f -#define WOL_LENGTH_SHIFT 8 - - -/* Receive and Transmit Descriptors ******************************************/ - -/* Transmit Descriptor struct */ -typedef struct s_HwTxd { - SK_U32 volatile TxCtrl; /* Transmit Buffer Control Field */ - SK_U32 TxNext; /* Physical Address Pointer to the next TxD */ - SK_U32 TxAdrLo; /* Physical Tx Buffer Address lower dword */ - SK_U32 TxAdrHi; /* Physical Tx Buffer Address upper dword */ - SK_U32 TxStat; /* Transmit Frame Status Word */ -#ifndef SK_USE_REV_DESC - SK_U16 TxTcpOffs; /* TCP Checksum Calculation Start Value */ - SK_U16 TxRes1; /* 16 bit reserved field */ - SK_U16 TxTcpWp; /* TCP Checksum Write Position */ - SK_U16 TxTcpSp; /* TCP Checksum Calculation Start Position */ -#else /* SK_USE_REV_DESC */ - SK_U16 TxRes1; /* 16 bit reserved field */ - SK_U16 TxTcpOffs; /* TCP Checksum Calculation Start Value */ - SK_U16 TxTcpSp; /* TCP Checksum Calculation Start Position */ - SK_U16 TxTcpWp; /* TCP Checksum Write Position */ -#endif /* SK_USE_REV_DESC */ - SK_U32 TxRes2; /* 32 bit reserved field */ -} SK_HWTXD; - -/* Receive Descriptor struct */ -typedef struct s_HwRxd { - SK_U32 volatile RxCtrl; /* Receive Buffer Control Field */ - SK_U32 RxNext; /* Physical Address Pointer to the next RxD */ - SK_U32 RxAdrLo; /* Physical Rx Buffer Address lower dword */ - SK_U32 RxAdrHi; /* Physical Rx Buffer Address upper dword */ - SK_U32 RxStat; /* Receive Frame Status Word */ - SK_U32 RxTiSt; /* Receive Time Stamp (from XMAC on GENESIS) */ -#ifndef SK_USE_REV_DESC - SK_U16 RxTcpSum1; /* TCP Checksum 1 */ - SK_U16 RxTcpSum2; /* TCP Checksum 2 */ - SK_U16 RxTcpSp1; /* TCP Checksum Calculation Start Position 1 */ - SK_U16 RxTcpSp2; /* TCP Checksum Calculation Start Position 2 */ -#else /* SK_USE_REV_DESC */ - SK_U16 RxTcpSum2; /* TCP Checksum 2 */ - SK_U16 RxTcpSum1; /* TCP Checksum 1 */ - SK_U16 RxTcpSp2; /* TCP Checksum Calculation Start Position 2 */ - SK_U16 RxTcpSp1; /* TCP Checksum Calculation Start Position 1 */ -#endif /* SK_USE_REV_DESC */ -} SK_HWRXD; - -/* - * Drivers which use the reverse descriptor feature (PCI_OUR_REG_2) - * should set the define SK_USE_REV_DESC. - * Structures are 'normaly' not endianess dependent. But in - * this case the SK_U16 fields are bound to bit positions inside the - * descriptor. RxTcpSum1 e.g. must start at bit 0 within the 6.th DWord. - * The bit positions inside a DWord are of course endianess dependent and - * swaps if the DWord is swapped by the hardware. - */ - - -/* Descriptor Bit Definition */ -/* TxCtrl Transmit Buffer Control Field */ -/* RxCtrl Receive Buffer Control Field */ -#define BMU_OWN BIT_31 /* OWN bit: 0=host/1=BMU */ -#define BMU_STF BIT_30 /* Start of Frame */ -#define BMU_EOF BIT_29 /* End of Frame */ -#define BMU_IRQ_EOB BIT_28 /* Req "End of Buffer" IRQ */ -#define BMU_IRQ_EOF BIT_27 /* Req "End of Frame" IRQ */ -/* TxCtrl specific bits */ -#define BMU_STFWD BIT_26 /* (Tx) Store & Forward Frame */ -#define BMU_NO_FCS BIT_25 /* (Tx) Disable MAC FCS (CRC) generation */ -#define BMU_SW BIT_24 /* (Tx) 1 bit res. for SW use */ -/* RxCtrl specific bits */ -#define BMU_DEV_0 BIT_26 /* (Rx) Transfer data to Dev0 */ -#define BMU_STAT_VAL BIT_25 /* (Rx) Rx Status Valid */ -#define BMU_TIST_VAL BIT_24 /* (Rx) Rx TimeStamp Valid */ - /* Bit 23..16: BMU Check Opcodes */ -#define BMU_CHECK (0x55L<<16) /* Default BMU check */ -#define BMU_TCP_CHECK (0x56L<<16) /* Descr with TCP ext */ -#define BMU_UDP_CHECK (0x57L<<16) /* Descr with UDP ext (YUKON only) */ -#define BMU_BBC 0xffffL /* Bit 15.. 0: Buffer Byte Counter */ - -/* TxStat Transmit Frame Status Word */ -/* RxStat Receive Frame Status Word */ -/* - *Note: TxStat is reserved for ASIC loopback mode only - * - * The Bits of the Status words are defined in xmac_ii.h - * (see XMR_FS bits) - */ - -/* macros ********************************************************************/ - -/* Receive and Transmit Queues */ -#define Q_R1 0x0000 /* Receive Queue 1 */ -#define Q_R2 0x0080 /* Receive Queue 2 */ -#define Q_XS1 0x0200 /* Synchronous Transmit Queue 1 */ -#define Q_XA1 0x0280 /* Asynchronous Transmit Queue 1 */ -#define Q_XS2 0x0300 /* Synchronous Transmit Queue 2 */ -#define Q_XA2 0x0380 /* Asynchronous Transmit Queue 2 */ - -/* - * Macro Q_ADDR() - * - * Use this macro to access the Receive and Transmit Queue Registers. - * - * para: - * Queue Queue to access. - * Values: Q_R1, Q_R2, Q_XS1, Q_XA1, Q_XS2, and Q_XA2 - * Offs Queue register offset. - * Values: Q_D, Q_DA_L ... Q_T2, Q_T3 - * - * usage SK_IN32(pAC, Q_ADDR(Q_R2, Q_BC), pVal) - */ -#define Q_ADDR(Queue, Offs) (B8_Q_REGS + (Queue) + (Offs)) - -/* - * Macro RB_ADDR() - * - * Use this macro to access the RAM Buffer Registers. - * - * para: - * Queue Queue to access. - * Values: Q_R1, Q_R2, Q_XS1, Q_XA1, Q_XS2, and Q_XA2 - * Offs Queue register offset. - * Values: RB_START, RB_END ... RB_LEV, RB_CTRL - * - * usage SK_IN32(pAC, RB_ADDR(Q_R2, RB_RP), pVal) - */ -#define RB_ADDR(Queue, Offs) (B16_RAM_REGS + (Queue) + (Offs)) - - -/* MAC Related Registers */ -#define MAC_1 0 /* belongs to the port near the slot */ -#define MAC_2 1 /* belongs to the port far away from the slot */ - -/* - * Macro MR_ADDR() - * - * Use this macro to access a MAC Related Registers inside the ASIC. - * - * para: - * Mac MAC to access. - * Values: MAC_1, MAC_2 - * Offs MAC register offset. - * Values: RX_MFF_EA, RX_MFF_WP ... LNK_LED_REG, - * TX_MFF_EA, TX_MFF_WP ... TX_LED_TST - * - * usage SK_IN32(pAC, MR_ADDR(MAC_1, TX_MFF_EA), pVal) - */ -#define MR_ADDR(Mac, Offs) (((Mac) << 7) + (Offs)) - -#ifdef SK_LITTLE_ENDIAN -#define XM_WORD_LO 0 -#define XM_WORD_HI 1 -#else /* !SK_LITTLE_ENDIAN */ -#define XM_WORD_LO 1 -#define XM_WORD_HI 0 -#endif /* !SK_LITTLE_ENDIAN */ - - -/* - * macros to access the XMAC (GENESIS only) - * - * XM_IN16(), to read a 16 bit register (e.g. XM_MMU_CMD) - * XM_OUT16(), to write a 16 bit register (e.g. XM_MMU_CMD) - * XM_IN32(), to read a 32 bit register (e.g. XM_TX_EV_CNT) - * XM_OUT32(), to write a 32 bit register (e.g. XM_TX_EV_CNT) - * XM_INADDR(), to read a network address register (e.g. XM_SRC_CHK) - * XM_OUTADDR(), to write a network address register (e.g. XM_SRC_CHK) - * XM_INHASH(), to read the XM_HSM_CHK register - * XM_OUTHASH() to write the XM_HSM_CHK register - * - * para: - * Mac XMAC to access values: MAC_1 or MAC_2 - * IoC I/O context needed for SK I/O macros - * Reg XMAC Register to read or write - * (p)Val Value or pointer to the value which should be read or written - * - * usage: XM_OUT16(IoC, MAC_1, XM_MMU_CMD, Value); - */ - -#define XMA(Mac, Reg) \ - ((BASE_XMAC_1 + (Mac) * (BASE_XMAC_2 - BASE_XMAC_1)) | ((Reg) << 1)) - -#define XM_IN16(IoC, Mac, Reg, pVal) \ - SK_IN16((IoC), XMA((Mac), (Reg)), (pVal)) - -#define XM_OUT16(IoC, Mac, Reg, Val) \ - SK_OUT16((IoC), XMA((Mac), (Reg)), (Val)) - -#define XM_IN32(IoC, Mac, Reg, pVal) { \ - SK_IN16((IoC), XMA((Mac), (Reg)), \ - (SK_U16 SK_FAR*)&((SK_U16 SK_FAR*)(pVal))[XM_WORD_LO]); \ - SK_IN16((IoC), XMA((Mac), (Reg+2)), \ - (SK_U16 SK_FAR*)&((SK_U16 SK_FAR*)(pVal))[XM_WORD_HI]); \ -} - -#define XM_OUT32(IoC, Mac, Reg, Val) { \ - SK_OUT16((IoC), XMA((Mac), (Reg)), (SK_U16)((Val) & 0xffffL)); \ - SK_OUT16((IoC), XMA((Mac), (Reg+2)), (SK_U16)(((Val) >> 16) & 0xffffL));\ -} - -/* Remember: we are always writing to / reading from LITTLE ENDIAN memory */ - -#define XM_INADDR(IoC, Mac, Reg, pVal) { \ - SK_U16 Word; \ - SK_U8 *pByte; \ - pByte = (SK_U8 *)&((SK_U8 *)(pVal))[0]; \ - SK_IN16((IoC), XMA((Mac), (Reg)), &Word); \ - pByte[0] = (SK_U8)(Word & 0x00ff); \ - pByte[1] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), XMA((Mac), (Reg+2)), &Word); \ - pByte[2] = (SK_U8)(Word & 0x00ff); \ - pByte[3] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), XMA((Mac), (Reg+4)), &Word); \ - pByte[4] = (SK_U8)(Word & 0x00ff); \ - pByte[5] = (SK_U8)((Word >> 8) & 0x00ff); \ -} - -#define XM_OUTADDR(IoC, Mac, Reg, pVal) { \ - SK_U8 SK_FAR *pByte; \ - pByte = (SK_U8 SK_FAR *)&((SK_U8 SK_FAR *)(pVal))[0]; \ - SK_OUT16((IoC), XMA((Mac), (Reg)), (SK_U16) \ - (((SK_U16)(pByte[0]) & 0x00ff) | \ - (((SK_U16)(pByte[1]) << 8) & 0xff00))); \ - SK_OUT16((IoC), XMA((Mac), (Reg+2)), (SK_U16) \ - (((SK_U16)(pByte[2]) & 0x00ff) | \ - (((SK_U16)(pByte[3]) << 8) & 0xff00))); \ - SK_OUT16((IoC), XMA((Mac), (Reg+4)), (SK_U16) \ - (((SK_U16)(pByte[4]) & 0x00ff) | \ - (((SK_U16)(pByte[5]) << 8) & 0xff00))); \ -} - -#define XM_INHASH(IoC, Mac, Reg, pVal) { \ - SK_U16 Word; \ - SK_U8 SK_FAR *pByte; \ - pByte = (SK_U8 SK_FAR *)&((SK_U8 SK_FAR *)(pVal))[0]; \ - SK_IN16((IoC), XMA((Mac), (Reg)), &Word); \ - pByte[0] = (SK_U8)(Word & 0x00ff); \ - pByte[1] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), XMA((Mac), (Reg+2)), &Word); \ - pByte[2] = (SK_U8)(Word & 0x00ff); \ - pByte[3] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), XMA((Mac), (Reg+4)), &Word); \ - pByte[4] = (SK_U8)(Word & 0x00ff); \ - pByte[5] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), XMA((Mac), (Reg+6)), &Word); \ - pByte[6] = (SK_U8)(Word & 0x00ff); \ - pByte[7] = (SK_U8)((Word >> 8) & 0x00ff); \ -} - -#define XM_OUTHASH(IoC, Mac, Reg, pVal) { \ - SK_U8 SK_FAR *pByte; \ - pByte = (SK_U8 SK_FAR *)&((SK_U8 SK_FAR *)(pVal))[0]; \ - SK_OUT16((IoC), XMA((Mac), (Reg)), (SK_U16) \ - (((SK_U16)(pByte[0]) & 0x00ff)| \ - (((SK_U16)(pByte[1]) << 8) & 0xff00))); \ - SK_OUT16((IoC), XMA((Mac), (Reg+2)), (SK_U16) \ - (((SK_U16)(pByte[2]) & 0x00ff)| \ - (((SK_U16)(pByte[3]) << 8) & 0xff00))); \ - SK_OUT16((IoC), XMA((Mac), (Reg+4)), (SK_U16) \ - (((SK_U16)(pByte[4]) & 0x00ff)| \ - (((SK_U16)(pByte[5]) << 8) & 0xff00))); \ - SK_OUT16((IoC), XMA((Mac), (Reg+6)), (SK_U16) \ - (((SK_U16)(pByte[6]) & 0x00ff)| \ - (((SK_U16)(pByte[7]) << 8) & 0xff00))); \ -} - -/* - * macros to access the GMAC (YUKON only) - * - * GM_IN16(), to read a 16 bit register (e.g. GM_GP_STAT) - * GM_OUT16(), to write a 16 bit register (e.g. GM_GP_CTRL) - * GM_IN32(), to read a 32 bit register (e.g. GM_) - * GM_OUT32(), to write a 32 bit register (e.g. GM_) - * GM_INADDR(), to read a network address register (e.g. GM_SRC_ADDR_1L) - * GM_OUTADDR(), to write a network address register (e.g. GM_SRC_ADDR_2L) - * GM_INHASH(), to read the GM_MC_ADDR_H1 register - * GM_OUTHASH() to write the GM_MC_ADDR_H1 register - * - * para: - * Mac GMAC to access values: MAC_1 or MAC_2 - * IoC I/O context needed for SK I/O macros - * Reg GMAC Register to read or write - * (p)Val Value or pointer to the value which should be read or written - * - * usage: GM_OUT16(IoC, MAC_1, GM_GP_CTRL, Value); - */ - -#define GMA(Mac, Reg) \ - ((BASE_GMAC_1 + (Mac) * (BASE_GMAC_2 - BASE_GMAC_1)) | (Reg)) - -#define GM_IN16(IoC, Mac, Reg, pVal) \ - SK_IN16((IoC), GMA((Mac), (Reg)), (pVal)) - -#define GM_OUT16(IoC, Mac, Reg, Val) \ - SK_OUT16((IoC), GMA((Mac), (Reg)), (Val)) - -#define GM_IN32(IoC, Mac, Reg, pVal) { \ - SK_IN16((IoC), GMA((Mac), (Reg)), \ - (SK_U16 SK_FAR*)&((SK_U16 SK_FAR*)(pVal))[XM_WORD_LO]); \ - SK_IN16((IoC), GMA((Mac), (Reg+4)), \ - (SK_U16 SK_FAR*)&((SK_U16 SK_FAR*)(pVal))[XM_WORD_HI]); \ -} - -#define GM_OUT32(IoC, Mac, Reg, Val) { \ - SK_OUT16((IoC), GMA((Mac), (Reg)), (SK_U16)((Val) & 0xffffL)); \ - SK_OUT16((IoC), GMA((Mac), (Reg+4)), (SK_U16)(((Val) >> 16) & 0xffffL));\ -} - -#define GM_INADDR(IoC, Mac, Reg, pVal) { \ - SK_U16 Word; \ - SK_U8 *pByte; \ - pByte = (SK_U8 *)&((SK_U8 *)(pVal))[0]; \ - SK_IN16((IoC), GMA((Mac), (Reg)), &Word); \ - pByte[0] = (SK_U8)(Word & 0x00ff); \ - pByte[1] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), GMA((Mac), (Reg+4)), &Word); \ - pByte[2] = (SK_U8)(Word & 0x00ff); \ - pByte[3] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), GMA((Mac), (Reg+8)), &Word); \ - pByte[4] = (SK_U8)(Word & 0x00ff); \ - pByte[5] = (SK_U8)((Word >> 8) & 0x00ff); \ -} - -#define GM_OUTADDR(IoC, Mac, Reg, pVal) { \ - SK_U8 SK_FAR *pByte; \ - pByte = (SK_U8 SK_FAR *)&((SK_U8 SK_FAR *)(pVal))[0]; \ - SK_OUT16((IoC), GMA((Mac), (Reg)), (SK_U16) \ - (((SK_U16)(pByte[0]) & 0x00ff) | \ - (((SK_U16)(pByte[1]) << 8) & 0xff00))); \ - SK_OUT16((IoC), GMA((Mac), (Reg+4)), (SK_U16) \ - (((SK_U16)(pByte[2]) & 0x00ff) | \ - (((SK_U16)(pByte[3]) << 8) & 0xff00))); \ - SK_OUT16((IoC), GMA((Mac), (Reg+8)), (SK_U16) \ - (((SK_U16)(pByte[4]) & 0x00ff) | \ - (((SK_U16)(pByte[5]) << 8) & 0xff00))); \ -} - -#define GM_INHASH(IoC, Mac, Reg, pVal) { \ - SK_U16 Word; \ - SK_U8 *pByte; \ - pByte = (SK_U8 *)&((SK_U8 *)(pVal))[0]; \ - SK_IN16((IoC), GMA((Mac), (Reg)), &Word); \ - pByte[0] = (SK_U8)(Word & 0x00ff); \ - pByte[1] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), GMA((Mac), (Reg+4)), &Word); \ - pByte[2] = (SK_U8)(Word & 0x00ff); \ - pByte[3] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), GMA((Mac), (Reg+8)), &Word); \ - pByte[4] = (SK_U8)(Word & 0x00ff); \ - pByte[5] = (SK_U8)((Word >> 8) & 0x00ff); \ - SK_IN16((IoC), GMA((Mac), (Reg+12)), &Word); \ - pByte[6] = (SK_U8)(Word & 0x00ff); \ - pByte[7] = (SK_U8)((Word >> 8) & 0x00ff); \ -} - -#define GM_OUTHASH(IoC, Mac, Reg, pVal) { \ - SK_U8 *pByte; \ - pByte = (SK_U8 *)&((SK_U8 *)(pVal))[0]; \ - SK_OUT16((IoC), GMA((Mac), (Reg)), (SK_U16) \ - (((SK_U16)(pByte[0]) & 0x00ff)| \ - (((SK_U16)(pByte[1]) << 8) & 0xff00))); \ - SK_OUT16((IoC), GMA((Mac), (Reg+4)), (SK_U16) \ - (((SK_U16)(pByte[2]) & 0x00ff)| \ - (((SK_U16)(pByte[3]) << 8) & 0xff00))); \ - SK_OUT16((IoC), GMA((Mac), (Reg+8)), (SK_U16) \ - (((SK_U16)(pByte[4]) & 0x00ff)| \ - (((SK_U16)(pByte[5]) << 8) & 0xff00))); \ - SK_OUT16((IoC), GMA((Mac), (Reg+12)), (SK_U16) \ - (((SK_U16)(pByte[6]) & 0x00ff)| \ - (((SK_U16)(pByte[7]) << 8) & 0xff00))); \ -} - -/* - * Different MAC Types - */ -#define SK_MAC_XMAC 0 /* Xaqti XMAC II */ -#define SK_MAC_GMAC 1 /* Marvell GMAC */ - -/* - * Different PHY Types - */ -#define SK_PHY_XMAC 0 /* integrated in XMAC II */ -#define SK_PHY_BCOM 1 /* Broadcom BCM5400 */ -#define SK_PHY_LONE 2 /* Level One LXT1000 */ -#define SK_PHY_NAT 3 /* National DP83891 */ -#define SK_PHY_MARV_COPPER 4 /* Marvell 88E1011S */ -#define SK_PHY_MARV_FIBER 5 /* Marvell 88E1011S working on fiber */ - -/* - * PHY addresses (bits 12..8 of PHY address reg) - */ -#define PHY_ADDR_XMAC (0<<8) -#define PHY_ADDR_BCOM (1<<8) -#define PHY_ADDR_LONE (3<<8) -#define PHY_ADDR_NAT (0<<8) - -/* GPHY address (bits 15..11 of SMI control reg) */ -#define PHY_ADDR_MARV 0 - -/* - * macros to access the PHY - * - * PHY_READ() read a 16 bit value from the PHY - * PHY_WRITE() write a 16 bit value to the PHY - * - * para: - * IoC I/O context needed for SK I/O macros - * pPort Pointer to port struct for PhyAddr - * Mac XMAC to access values: MAC_1 or MAC_2 - * PhyReg PHY Register to read or write - * (p)Val Value or pointer to the value which should be read or - * written. - * - * usage: PHY_READ(IoC, pPort, MAC_1, PHY_CTRL, Value); - * Warning: a PHY_READ on an uninitialized PHY (PHY still in reset) never - * comes back. This is checked in DEBUG mode. - */ -#ifndef DEBUG -#define PHY_READ(IoC, pPort, Mac, PhyReg, pVal) { \ - SK_U16 Mmu; \ - \ - XM_OUT16((IoC), (Mac), XM_PHY_ADDR, (PhyReg) | (pPort)->PhyAddr); \ - XM_IN16((IoC), (Mac), XM_PHY_DATA, (pVal)); \ - if ((pPort)->PhyType != SK_PHY_XMAC) { \ - do { \ - XM_IN16((IoC), (Mac), XM_MMU_CMD, &Mmu); \ - } while ((Mmu & XM_MMU_PHY_RDY) == 0); \ - XM_IN16((IoC), (Mac), XM_PHY_DATA, (pVal)); \ - } \ -} -#else -#define PHY_READ(IoC, pPort, Mac, PhyReg, pVal) { \ - SK_U16 Mmu; \ - int __i = 0; \ - \ - XM_OUT16((IoC), (Mac), XM_PHY_ADDR, (PhyReg) | (pPort)->PhyAddr); \ - XM_IN16((IoC), (Mac), XM_PHY_DATA, (pVal)); \ - if ((pPort)->PhyType != SK_PHY_XMAC) { \ - do { \ - XM_IN16((IoC), (Mac), XM_MMU_CMD, &Mmu); \ - __i++; \ - if (__i > 100000) { \ - SK_DBG_PRINTF("*****************************\n"); \ - SK_DBG_PRINTF("PHY_READ on uninitialized PHY\n"); \ - SK_DBG_PRINTF("*****************************\n"); \ - break; \ - } \ - } while ((Mmu & XM_MMU_PHY_RDY) == 0); \ - XM_IN16((IoC), (Mac), XM_PHY_DATA, (pVal)); \ - } \ -} -#endif /* DEBUG */ - -#define PHY_WRITE(IoC, pPort, Mac, PhyReg, Val) { \ - SK_U16 Mmu; \ - \ - if ((pPort)->PhyType != SK_PHY_XMAC) { \ - do { \ - XM_IN16((IoC), (Mac), XM_MMU_CMD, &Mmu); \ - } while ((Mmu & XM_MMU_PHY_BUSY) != 0); \ - } \ - XM_OUT16((IoC), (Mac), XM_PHY_ADDR, (PhyReg) | (pPort)->PhyAddr); \ - XM_OUT16((IoC), (Mac), XM_PHY_DATA, (Val)); \ - if ((pPort)->PhyType != SK_PHY_XMAC) { \ - do { \ - XM_IN16((IoC), (Mac), XM_MMU_CMD, &Mmu); \ - } while ((Mmu & XM_MMU_PHY_BUSY) != 0); \ - } \ -} - -/* - * Macro PCI_C() - * - * Use this macro to access PCI config register from the I/O space. - * - * para: - * Addr PCI configuration register to access. - * Values: PCI_VENDOR_ID ... PCI_VPD_ADR_REG, - * - * usage SK_IN16(pAC, PCI_C(PCI_VENDOR_ID), pVal); - */ -#define PCI_C(Addr) (B7_CFG_SPC + (Addr)) /* PCI Config Space */ - -/* - * Macro SK_HW_ADDR(Base, Addr) - * - * Calculates the effective HW address - * - * para: - * Base I/O or memory base address - * Addr Address offset - * - * usage: May be used in SK_INxx and SK_OUTxx macros - * #define SK_IN8(pAC, Addr, pVal) ...\ - * *pVal = (SK_U8)inp(SK_HW_ADDR(pAC->Hw.Iop, Addr))) - */ -#ifdef SK_MEM_MAPPED_IO -#define SK_HW_ADDR(Base, Addr) ((Base) + (Addr)) -#else /* SK_MEM_MAPPED_IO */ -#define SK_HW_ADDR(Base, Addr) \ - ((Base) + (((Addr) & 0x7f) | (((Addr) >> 7 > 0) ? 0x80 : 0))) -#endif /* SK_MEM_MAPPED_IO */ - -#define SZ_LONG (sizeof(SK_U32)) - -/* - * Macro SK_HWAC_LINK_LED() - * - * Use this macro to set the link LED mode. - * para: - * pAC Pointer to adapter context struct - * IoC I/O context needed for SK I/O macros - * Port Port number - * Mode Mode to set for this LED - */ -#define SK_HWAC_LINK_LED(pAC, IoC, Port, Mode) \ - SK_OUT8(IoC, MR_ADDR(Port, LNK_LED_REG), Mode); - - -/* typedefs *******************************************************************/ - - -/* function prototypes ********************************************************/ - -#ifdef __cplusplus -} -#endif /* __cplusplus */ - -#endif /* __INC_SKGEHW_H */ diff --git a/drivers/net/sk98lin/h/skgehwt.h b/drivers/net/sk98lin/h/skgehwt.h deleted file mode 100644 index e6b0016a695c..000000000000 --- a/drivers/net/sk98lin/h/skgehwt.h +++ /dev/null @@ -1,48 +0,0 @@ -/****************************************************************************** - * - * Name: skhwt.h - * Project: Gigabit Ethernet Adapters, Event Scheduler Module - * Version: $Revision: 1.7 $ - * Date: $Date: 2003/09/16 12:55:08 $ - * Purpose: Defines for the hardware timer functions - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * SKGEHWT.H contains all defines and types for the timer functions - */ - -#ifndef _SKGEHWT_H_ -#define _SKGEHWT_H_ - -/* - * SK Hardware Timer - * - needed wherever the HWT module is used - * - use in Adapters context name pAC->Hwt - */ -typedef struct s_Hwt { - SK_U32 TStart; /* HWT start */ - SK_U32 TStop; /* HWT stop */ - int TActive; /* HWT: flag : active/inactive */ -} SK_HWT; - -extern void SkHwtInit(SK_AC *pAC, SK_IOC Ioc); -extern void SkHwtStart(SK_AC *pAC, SK_IOC Ioc, SK_U32 Time); -extern void SkHwtStop(SK_AC *pAC, SK_IOC Ioc); -extern SK_U32 SkHwtRead(SK_AC *pAC, SK_IOC Ioc); -extern void SkHwtIsr(SK_AC *pAC, SK_IOC Ioc); -#endif /* _SKGEHWT_H_ */ diff --git a/drivers/net/sk98lin/h/skgei2c.h b/drivers/net/sk98lin/h/skgei2c.h deleted file mode 100644 index d9b6f6d8dfe2..000000000000 --- a/drivers/net/sk98lin/h/skgei2c.h +++ /dev/null @@ -1,210 +0,0 @@ -/****************************************************************************** - * - * Name: skgei2c.h - * Project: Gigabit Ethernet Adapters, TWSI-Module - * Version: $Revision: 1.25 $ - * Date: $Date: 2003/10/20 09:06:05 $ - * Purpose: Special defines for TWSI - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * SKGEI2C.H contains all SK-98xx specific defines for the TWSI handling - */ - -#ifndef _INC_SKGEI2C_H_ -#define _INC_SKGEI2C_H_ - -/* - * Macros to access the B2_I2C_CTRL - */ -#define SK_I2C_CTL(IoC, flag, dev, dev_size, reg, burst) \ - SK_OUT32(IoC, B2_I2C_CTRL,\ - (flag ? 0x80000000UL : 0x0L) | \ - (((SK_U32)reg << 16) & I2C_ADDR) | \ - (((SK_U32)dev << 9) & I2C_DEV_SEL) | \ - (dev_size & I2C_DEV_SIZE) | \ - ((burst << 4) & I2C_BURST_LEN)) - -#define SK_I2C_STOP(IoC) { \ - SK_U32 I2cCtrl; \ - SK_IN32(IoC, B2_I2C_CTRL, &I2cCtrl); \ - SK_OUT32(IoC, B2_I2C_CTRL, I2cCtrl | I2C_STOP); \ -} - -#define SK_I2C_GET_CTL(IoC, pI2cCtrl) SK_IN32(IoC, B2_I2C_CTRL, pI2cCtrl) - -/* - * Macros to access the TWSI SW Registers - */ -#define SK_I2C_SET_BIT(IoC, SetBits) { \ - SK_U8 OrgBits; \ - SK_IN8(IoC, B2_I2C_SW, &OrgBits); \ - SK_OUT8(IoC, B2_I2C_SW, OrgBits | (SK_U8)(SetBits)); \ -} - -#define SK_I2C_CLR_BIT(IoC, ClrBits) { \ - SK_U8 OrgBits; \ - SK_IN8(IoC, B2_I2C_SW, &OrgBits); \ - SK_OUT8(IoC, B2_I2C_SW, OrgBits & ~((SK_U8)(ClrBits))); \ -} - -#define SK_I2C_GET_SW(IoC, pI2cSw) SK_IN8(IoC, B2_I2C_SW, pI2cSw) - -/* - * define the possible sensor states - */ -#define SK_SEN_IDLE 0 /* Idle: sensor not read */ -#define SK_SEN_VALUE 1 /* Value Read cycle */ -#define SK_SEN_VALEXT 2 /* Extended Value Read cycle */ - -/* - * Conversion factor to convert read Voltage sensor to milli Volt - * Conversion factor to convert read Temperature sensor to 10th degree Celsius - */ -#define SK_LM80_VT_LSB 22 /* 22mV LSB resolution */ -#define SK_LM80_TEMP_LSB 10 /* 1 degree LSB resolution */ -#define SK_LM80_TEMPEXT_LSB 5 /* 0.5 degree LSB resolution for ext. val. */ - -/* - * formula: counter = (22500*60)/(rpm * divisor * pulses/2) - * assuming: 6500rpm, 4 pulses, divisor 1 - */ -#define SK_LM80_FAN_FAKTOR ((22500L*60)/(1*2)) - -/* - * Define sensor management data - * Maximum is reached on Genesis copper dual port and Yukon-64 - * Board specific maximum is in pAC->I2c.MaxSens - */ -#define SK_MAX_SENSORS 8 /* maximal no. of installed sensors */ -#define SK_MIN_SENSORS 5 /* minimal no. of installed sensors */ - -/* - * To watch the state machine (SM) use the timer in two ways - * instead of one as hitherto - */ -#define SK_TIMER_WATCH_SM 0 /* Watch the SM to finish in a spec. time */ -#define SK_TIMER_NEW_GAUGING 1 /* Start a new gauging when timer expires */ - -/* - * Defines for the individual thresholds - */ - -/* Temperature sensor */ -#define SK_SEN_TEMP_HIGH_ERR 800 /* Temperature High Err Threshold */ -#define SK_SEN_TEMP_HIGH_WARN 700 /* Temperature High Warn Threshold */ -#define SK_SEN_TEMP_LOW_WARN 100 /* Temperature Low Warn Threshold */ -#define SK_SEN_TEMP_LOW_ERR 0 /* Temperature Low Err Threshold */ - -/* VCC which should be 5 V */ -#define SK_SEN_PCI_5V_HIGH_ERR 5588 /* Voltage PCI High Err Threshold */ -#define SK_SEN_PCI_5V_HIGH_WARN 5346 /* Voltage PCI High Warn Threshold */ -#define SK_SEN_PCI_5V_LOW_WARN 4664 /* Voltage PCI Low Warn Threshold */ -#define SK_SEN_PCI_5V_LOW_ERR 4422 /* Voltage PCI Low Err Threshold */ - -/* - * VIO may be 5 V or 3.3 V. Initialization takes two parts: - * 1. Initialize lowest lower limit and highest higher limit. - * 2. After the first value is read correct the upper or the lower limit to - * the appropriate C constant. - * - * Warning limits are +-5% of the exepected voltage. - * Error limits are +-10% of the expected voltage. - */ - -/* Bug fix AF: 16.Aug.2001: Correct the init base of LM80 sensor */ - -#define SK_SEN_PCI_IO_5V_HIGH_ERR 5566 /* + 10% V PCI-IO High Err Threshold */ -#define SK_SEN_PCI_IO_5V_HIGH_WARN 5324 /* + 5% V PCI-IO High Warn Threshold */ - /* 5000 mVolt */ -#define SK_SEN_PCI_IO_5V_LOW_WARN 4686 /* - 5% V PCI-IO Low Warn Threshold */ -#define SK_SEN_PCI_IO_5V_LOW_ERR 4444 /* - 10% V PCI-IO Low Err Threshold */ - -#define SK_SEN_PCI_IO_RANGE_LIMITER 4000 /* 4000 mV range delimiter */ - -/* correction values for the second pass */ -#define SK_SEN_PCI_IO_3V3_HIGH_ERR 3850 /* + 15% V PCI-IO High Err Threshold */ -#define SK_SEN_PCI_IO_3V3_HIGH_WARN 3674 /* + 10% V PCI-IO High Warn Threshold */ - /* 3300 mVolt */ -#define SK_SEN_PCI_IO_3V3_LOW_WARN 2926 /* - 10% V PCI-IO Low Warn Threshold */ -#define SK_SEN_PCI_IO_3V3_LOW_ERR 2772 /* - 15% V PCI-IO Low Err Threshold */ - -/* - * VDD voltage - */ -#define SK_SEN_VDD_HIGH_ERR 3630 /* Voltage ASIC High Err Threshold */ -#define SK_SEN_VDD_HIGH_WARN 3476 /* Voltage ASIC High Warn Threshold */ -#define SK_SEN_VDD_LOW_WARN 3146 /* Voltage ASIC Low Warn Threshold */ -#define SK_SEN_VDD_LOW_ERR 2970 /* Voltage ASIC Low Err Threshold */ - -/* - * PHY PLL 3V3 voltage - */ -#define SK_SEN_PLL_3V3_HIGH_ERR 3630 /* Voltage PMA High Err Threshold */ -#define SK_SEN_PLL_3V3_HIGH_WARN 3476 /* Voltage PMA High Warn Threshold */ -#define SK_SEN_PLL_3V3_LOW_WARN 3146 /* Voltage PMA Low Warn Threshold */ -#define SK_SEN_PLL_3V3_LOW_ERR 2970 /* Voltage PMA Low Err Threshold */ - -/* - * VAUX (YUKON only) - */ -#define SK_SEN_VAUX_3V3_HIGH_ERR 3630 /* Voltage VAUX High Err Threshold */ -#define SK_SEN_VAUX_3V3_HIGH_WARN 3476 /* Voltage VAUX High Warn Threshold */ -#define SK_SEN_VAUX_3V3_LOW_WARN 3146 /* Voltage VAUX Low Warn Threshold */ -#define SK_SEN_VAUX_3V3_LOW_ERR 2970 /* Voltage VAUX Low Err Threshold */ -#define SK_SEN_VAUX_0V_WARN_ERR 0 /* if VAUX not present */ -#define SK_SEN_VAUX_RANGE_LIMITER 1000 /* 1000 mV range delimiter */ - -/* - * PHY 2V5 voltage - */ -#define SK_SEN_PHY_2V5_HIGH_ERR 2750 /* Voltage PHY High Err Threshold */ -#define SK_SEN_PHY_2V5_HIGH_WARN 2640 /* Voltage PHY High Warn Threshold */ -#define SK_SEN_PHY_2V5_LOW_WARN 2376 /* Voltage PHY Low Warn Threshold */ -#define SK_SEN_PHY_2V5_LOW_ERR 2222 /* Voltage PHY Low Err Threshold */ - -/* - * ASIC Core 1V5 voltage (YUKON only) - */ -#define SK_SEN_CORE_1V5_HIGH_ERR 1650 /* Voltage ASIC Core High Err Threshold */ -#define SK_SEN_CORE_1V5_HIGH_WARN 1575 /* Voltage ASIC Core High Warn Threshold */ -#define SK_SEN_CORE_1V5_LOW_WARN 1425 /* Voltage ASIC Core Low Warn Threshold */ -#define SK_SEN_CORE_1V5_LOW_ERR 1350 /* Voltage ASIC Core Low Err Threshold */ - -/* - * FAN 1 speed - */ -/* assuming: 6500rpm +-15%, 4 pulses, - * warning at: 80 % - * error at: 70 % - * no upper limit - */ -#define SK_SEN_FAN_HIGH_ERR 20000 /* FAN Speed High Err Threshold */ -#define SK_SEN_FAN_HIGH_WARN 20000 /* FAN Speed High Warn Threshold */ -#define SK_SEN_FAN_LOW_WARN 5200 /* FAN Speed Low Warn Threshold */ -#define SK_SEN_FAN_LOW_ERR 4550 /* FAN Speed Low Err Threshold */ - -/* - * Some Voltages need dynamic thresholds - */ -#define SK_SEN_DYN_INIT_NONE 0 /* No dynamic init of thresholds */ -#define SK_SEN_DYN_INIT_PCI_IO 10 /* Init PCI-IO with new thresholds */ -#define SK_SEN_DYN_INIT_VAUX 11 /* Init VAUX with new thresholds */ - -extern int SkLm80ReadSensor(SK_AC *pAC, SK_IOC IoC, SK_SENSOR *pSen); -#endif /* n_INC_SKGEI2C_H */ diff --git a/drivers/net/sk98lin/h/skgeinit.h b/drivers/net/sk98lin/h/skgeinit.h deleted file mode 100644 index 143e635ec24d..000000000000 --- a/drivers/net/sk98lin/h/skgeinit.h +++ /dev/null @@ -1,797 +0,0 @@ -/****************************************************************************** - * - * Name: skgeinit.h - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.83 $ - * Date: $Date: 2003/09/16 14:07:37 $ - * Purpose: Structures and prototypes for the GE Init Module - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef __INC_SKGEINIT_H_ -#define __INC_SKGEINIT_H_ - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/* defines ********************************************************************/ - -#define SK_TEST_VAL 0x11335577UL - -/* modifying Link LED behaviour (used with SkGeLinkLED()) */ -#define SK_LNK_OFF LED_OFF -#define SK_LNK_ON (LED_ON | LED_BLK_OFF | LED_SYNC_OFF) -#define SK_LNK_BLINK (LED_ON | LED_BLK_ON | LED_SYNC_ON) -#define SK_LNK_PERM (LED_ON | LED_BLK_OFF | LED_SYNC_ON) -#define SK_LNK_TST (LED_ON | LED_BLK_ON | LED_SYNC_OFF) - -/* parameter 'Mode' when calling SK_HWAC_LINK_LED() */ -#define SK_LED_OFF LED_OFF -#define SK_LED_ACTIVE (LED_ON | LED_BLK_OFF | LED_SYNC_OFF) -#define SK_LED_STANDBY (LED_ON | LED_BLK_ON | LED_SYNC_OFF) - -/* addressing LED Registers in SkGeXmitLED() */ -#define XMIT_LED_INI 0 -#define XMIT_LED_CNT (RX_LED_VAL - RX_LED_INI) -#define XMIT_LED_CTRL (RX_LED_CTRL- RX_LED_INI) -#define XMIT_LED_TST (RX_LED_TST - RX_LED_INI) - -/* parameter 'Mode' when calling SkGeXmitLED() */ -#define SK_LED_DIS 0 -#define SK_LED_ENA 1 -#define SK_LED_TST 2 - -/* Counter and Timer constants, for a host clock of 62.5 MHz */ -#define SK_XMIT_DUR 0x002faf08UL /* 50 ms */ -#define SK_BLK_DUR 0x01dcd650UL /* 500 ms */ - -#define SK_DPOLL_DEF 0x00ee6b28UL /* 250 ms at 62.5 MHz */ - -#define SK_DPOLL_MAX 0x00ffffffUL /* 268 ms at 62.5 MHz */ - /* 215 ms at 78.12 MHz */ - -#define SK_FACT_62 100 /* is given in percent */ -#define SK_FACT_53 85 /* on GENESIS: 53.12 MHz */ -#define SK_FACT_78 125 /* on YUKON: 78.12 MHz */ - -/* Timeout values */ -#define SK_MAC_TO_53 72 /* MAC arbiter timeout */ -#define SK_PKT_TO_53 0x2000 /* Packet arbiter timeout */ -#define SK_PKT_TO_MAX 0xffff /* Maximum value */ -#define SK_RI_TO_53 36 /* RAM interface timeout */ - -#define SK_PHY_ACC_TO 600000 /* PHY access timeout */ - -/* RAM Buffer High Pause Threshold values */ -#define SK_RB_ULPP ( 8 * 1024) /* Upper Level in kB/8 */ -#define SK_RB_LLPP_S (10 * 1024) /* Lower Level for small Queues */ -#define SK_RB_LLPP_B (16 * 1024) /* Lower Level for big Queues */ - -#ifndef SK_BMU_RX_WM -#define SK_BMU_RX_WM 0x600 /* BMU Rx Watermark */ -#endif -#ifndef SK_BMU_TX_WM -#define SK_BMU_TX_WM 0x600 /* BMU Tx Watermark */ -#endif - -/* XMAC II Rx High Watermark */ -#define SK_XM_RX_HI_WM 0x05aa /* 1450 */ - -/* XMAC II Tx Threshold */ -#define SK_XM_THR_REDL 0x01fb /* .. for redundant link usage */ -#define SK_XM_THR_SL 0x01fb /* .. for single link adapters */ -#define SK_XM_THR_MULL 0x01fb /* .. for multiple link usage */ -#define SK_XM_THR_JUMBO 0x03fc /* .. for jumbo frame usage */ - -/* values for GIPortUsage */ -#define SK_RED_LINK 1 /* redundant link usage */ -#define SK_MUL_LINK 2 /* multiple link usage */ -#define SK_JUMBO_LINK 3 /* driver uses jumbo frames */ - -/* Minimum RAM Buffer Rx Queue Size */ -#define SK_MIN_RXQ_SIZE 16 /* 16 kB */ - -/* Minimum RAM Buffer Tx Queue Size */ -#define SK_MIN_TXQ_SIZE 16 /* 16 kB */ - -/* Queue Size units */ -#define QZ_UNITS 0x7 -#define QZ_STEP 8 - -/* Percentage of queue size from whole memory */ -/* 80 % for receive */ -#define RAM_QUOTA_RX 80L -/* 0% for sync transfer */ -#define RAM_QUOTA_SYNC 0L -/* the rest (20%) is taken for async transfer */ - -/* Get the rounded queue size in Bytes in 8k steps */ -#define ROUND_QUEUE_SIZE(SizeInBytes) \ - ((((unsigned long) (SizeInBytes) + (QZ_STEP*1024L)-1) / 1024) & \ - ~(QZ_STEP-1)) - -/* Get the rounded queue size in KBytes in 8k steps */ -#define ROUND_QUEUE_SIZE_KB(Kilobytes) \ - ROUND_QUEUE_SIZE((Kilobytes) * 1024L) - -/* Types of RAM Buffer Queues */ -#define SK_RX_SRAM_Q 1 /* small receive queue */ -#define SK_RX_BRAM_Q 2 /* big receive queue */ -#define SK_TX_RAM_Q 3 /* small or big transmit queue */ - -/* parameter 'Dir' when calling SkGeStopPort() */ -#define SK_STOP_TX 1 /* Stops the transmit path, resets the XMAC */ -#define SK_STOP_RX 2 /* Stops the receive path */ -#define SK_STOP_ALL 3 /* Stops Rx and Tx path, resets the XMAC */ - -/* parameter 'RstMode' when calling SkGeStopPort() */ -#define SK_SOFT_RST 1 /* perform a software reset */ -#define SK_HARD_RST 2 /* perform a hardware reset */ - -/* Init Levels */ -#define SK_INIT_DATA 0 /* Init level 0: init data structures */ -#define SK_INIT_IO 1 /* Init level 1: init with IOs */ -#define SK_INIT_RUN 2 /* Init level 2: init for run time */ - -/* Link Mode Parameter */ -#define SK_LMODE_HALF 1 /* Half Duplex Mode */ -#define SK_LMODE_FULL 2 /* Full Duplex Mode */ -#define SK_LMODE_AUTOHALF 3 /* AutoHalf Duplex Mode */ -#define SK_LMODE_AUTOFULL 4 /* AutoFull Duplex Mode */ -#define SK_LMODE_AUTOBOTH 5 /* AutoBoth Duplex Mode */ -#define SK_LMODE_AUTOSENSE 6 /* configured mode auto sensing */ -#define SK_LMODE_INDETERMINATED 7 /* indeterminated */ - -/* Auto-negotiation timeout in 100ms granularity */ -#define SK_AND_MAX_TO 6 /* Wait 600 msec before link comes up */ - -/* Auto-negotiation error codes */ -#define SK_AND_OK 0 /* no error */ -#define SK_AND_OTHER 1 /* other error than below */ -#define SK_AND_DUP_CAP 2 /* Duplex capabilities error */ - - -/* Link Speed Capabilities */ -#define SK_LSPEED_CAP_AUTO (1<<0) /* Automatic resolution */ -#define SK_LSPEED_CAP_10MBPS (1<<1) /* 10 Mbps */ -#define SK_LSPEED_CAP_100MBPS (1<<2) /* 100 Mbps */ -#define SK_LSPEED_CAP_1000MBPS (1<<3) /* 1000 Mbps */ -#define SK_LSPEED_CAP_INDETERMINATED (1<<4) /* indeterminated */ - -/* Link Speed Parameter */ -#define SK_LSPEED_AUTO 1 /* Automatic resolution */ -#define SK_LSPEED_10MBPS 2 /* 10 Mbps */ -#define SK_LSPEED_100MBPS 3 /* 100 Mbps */ -#define SK_LSPEED_1000MBPS 4 /* 1000 Mbps */ -#define SK_LSPEED_INDETERMINATED 5 /* indeterminated */ - -/* Link Speed Current State */ -#define SK_LSPEED_STAT_UNKNOWN 1 -#define SK_LSPEED_STAT_10MBPS 2 -#define SK_LSPEED_STAT_100MBPS 3 -#define SK_LSPEED_STAT_1000MBPS 4 -#define SK_LSPEED_STAT_INDETERMINATED 5 - - -/* Link Capability Parameter */ -#define SK_LMODE_CAP_HALF (1<<0) /* Half Duplex Mode */ -#define SK_LMODE_CAP_FULL (1<<1) /* Full Duplex Mode */ -#define SK_LMODE_CAP_AUTOHALF (1<<2) /* AutoHalf Duplex Mode */ -#define SK_LMODE_CAP_AUTOFULL (1<<3) /* AutoFull Duplex Mode */ -#define SK_LMODE_CAP_INDETERMINATED (1<<4) /* indeterminated */ - -/* Link Mode Current State */ -#define SK_LMODE_STAT_UNKNOWN 1 /* Unknown Duplex Mode */ -#define SK_LMODE_STAT_HALF 2 /* Half Duplex Mode */ -#define SK_LMODE_STAT_FULL 3 /* Full Duplex Mode */ -#define SK_LMODE_STAT_AUTOHALF 4 /* Half Duplex Mode obtained by Auto-Neg */ -#define SK_LMODE_STAT_AUTOFULL 5 /* Full Duplex Mode obtained by Auto-Neg */ -#define SK_LMODE_STAT_INDETERMINATED 6 /* indeterminated */ - -/* Flow Control Mode Parameter (and capabilities) */ -#define SK_FLOW_MODE_NONE 1 /* No Flow-Control */ -#define SK_FLOW_MODE_LOC_SEND 2 /* Local station sends PAUSE */ -#define SK_FLOW_MODE_SYMMETRIC 3 /* Both stations may send PAUSE */ -#define SK_FLOW_MODE_SYM_OR_REM 4 /* Both stations may send PAUSE or - * just the remote station may send PAUSE - */ -#define SK_FLOW_MODE_INDETERMINATED 5 /* indeterminated */ - -/* Flow Control Status Parameter */ -#define SK_FLOW_STAT_NONE 1 /* No Flow Control */ -#define SK_FLOW_STAT_REM_SEND 2 /* Remote Station sends PAUSE */ -#define SK_FLOW_STAT_LOC_SEND 3 /* Local station sends PAUSE */ -#define SK_FLOW_STAT_SYMMETRIC 4 /* Both station may send PAUSE */ -#define SK_FLOW_STAT_INDETERMINATED 5 /* indeterminated */ - -/* Master/Slave Mode Capabilities */ -#define SK_MS_CAP_AUTO (1<<0) /* Automatic resolution */ -#define SK_MS_CAP_MASTER (1<<1) /* This station is master */ -#define SK_MS_CAP_SLAVE (1<<2) /* This station is slave */ -#define SK_MS_CAP_INDETERMINATED (1<<3) /* indeterminated */ - -/* Set Master/Slave Mode Parameter (and capabilities) */ -#define SK_MS_MODE_AUTO 1 /* Automatic resolution */ -#define SK_MS_MODE_MASTER 2 /* This station is master */ -#define SK_MS_MODE_SLAVE 3 /* This station is slave */ -#define SK_MS_MODE_INDETERMINATED 4 /* indeterminated */ - -/* Master/Slave Status Parameter */ -#define SK_MS_STAT_UNSET 1 /* The M/S status is not set */ -#define SK_MS_STAT_MASTER 2 /* This station is master */ -#define SK_MS_STAT_SLAVE 3 /* This station is slave */ -#define SK_MS_STAT_FAULT 4 /* M/S resolution failed */ -#define SK_MS_STAT_INDETERMINATED 5 /* indeterminated */ - -/* parameter 'Mode' when calling SkXmSetRxCmd() */ -#define SK_STRIP_FCS_ON (1<<0) /* Enable FCS stripping of Rx frames */ -#define SK_STRIP_FCS_OFF (1<<1) /* Disable FCS stripping of Rx frames */ -#define SK_STRIP_PAD_ON (1<<2) /* Enable pad byte stripping of Rx fr */ -#define SK_STRIP_PAD_OFF (1<<3) /* Disable pad byte stripping of Rx fr */ -#define SK_LENERR_OK_ON (1<<4) /* Don't chk fr for in range len error */ -#define SK_LENERR_OK_OFF (1<<5) /* Check frames for in range len error */ -#define SK_BIG_PK_OK_ON (1<<6) /* Don't set Rx Error bit for big frames */ -#define SK_BIG_PK_OK_OFF (1<<7) /* Set Rx Error bit for big frames */ -#define SK_SELF_RX_ON (1<<8) /* Enable Rx of own packets */ -#define SK_SELF_RX_OFF (1<<9) /* Disable Rx of own packets */ - -/* parameter 'Para' when calling SkMacSetRxTxEn() */ -#define SK_MAC_LOOPB_ON (1<<0) /* Enable MAC Loopback Mode */ -#define SK_MAC_LOOPB_OFF (1<<1) /* Disable MAC Loopback Mode */ -#define SK_PHY_LOOPB_ON (1<<2) /* Enable PHY Loopback Mode */ -#define SK_PHY_LOOPB_OFF (1<<3) /* Disable PHY Loopback Mode */ -#define SK_PHY_FULLD_ON (1<<4) /* Enable GMII Full Duplex */ -#define SK_PHY_FULLD_OFF (1<<5) /* Disable GMII Full Duplex */ - -/* States of PState */ -#define SK_PRT_RESET 0 /* the port is reset */ -#define SK_PRT_STOP 1 /* the port is stopped (similar to SW reset) */ -#define SK_PRT_INIT 2 /* the port is initialized */ -#define SK_PRT_RUN 3 /* the port has an active link */ - -/* PHY power down modes */ -#define PHY_PM_OPERATIONAL_MODE 0 /* PHY operational mode */ -#define PHY_PM_DEEP_SLEEP 1 /* coma mode --> minimal power */ -#define PHY_PM_IEEE_POWER_DOWN 2 /* IEEE 22.2.4.1.5 compl. power down */ -#define PHY_PM_ENERGY_DETECT 3 /* energy detect */ -#define PHY_PM_ENERGY_DETECT_PLUS 4 /* energy detect plus */ - -/* Default receive frame limit for Workaround of XMAC Errata */ -#define SK_DEF_RX_WA_LIM SK_CONSTU64(100) - -/* values for GILedBlinkCtrl (LED Blink Control) */ -#define SK_ACT_LED_BLINK (1<<0) /* Active LED blinking */ -#define SK_DUP_LED_NORMAL (1<<1) /* Duplex LED normal */ -#define SK_LED_LINK100_ON (1<<2) /* Link 100M LED on */ - -/* Link Partner Status */ -#define SK_LIPA_UNKNOWN 0 /* Link partner is in unknown state */ -#define SK_LIPA_MANUAL 1 /* Link partner is in detected manual state */ -#define SK_LIPA_AUTO 2 /* Link partner is in auto-negotiation state */ - -/* Maximum Restarts before restart is ignored (3Com WA) */ -#define SK_MAX_LRESTART 3 /* Max. 3 times the link is restarted */ - -/* Max. Auto-neg. timeouts before link detection in sense mode is reset */ -#define SK_MAX_ANEG_TO 10 /* Max. 10 times the sense mode is reset */ - -/* structures *****************************************************************/ - -/* - * MAC specific functions - */ -typedef struct s_GeMacFunc { - int (*pFnMacUpdateStats)(SK_AC *pAC, SK_IOC IoC, unsigned int Port); - int (*pFnMacStatistic)(SK_AC *pAC, SK_IOC IoC, unsigned int Port, - SK_U16 StatAddr, SK_U32 SK_FAR *pVal); - int (*pFnMacResetCounter)(SK_AC *pAC, SK_IOC IoC, unsigned int Port); - int (*pFnMacOverflow)(SK_AC *pAC, SK_IOC IoC, unsigned int Port, - SK_U16 IStatus, SK_U64 SK_FAR *pVal); -} SK_GEMACFUNC; - -/* - * Port Structure - */ -typedef struct s_GePort { -#ifndef SK_DIAG - SK_TIMER PWaTimer; /* Workaround Timer */ - SK_TIMER HalfDupChkTimer; -#endif /* SK_DIAG */ - SK_U32 PPrevShorts; /* Previous Short Counter checking */ - SK_U32 PPrevFcs; /* Previous FCS Error Counter checking */ - SK_U64 PPrevRx; /* Previous RxOk Counter checking */ - SK_U64 PRxLim; /* Previous RxOk Counter checking */ - SK_U64 LastOctets; /* For half duplex hang check */ - int PLinkResCt; /* Link Restart Counter */ - int PAutoNegTimeOut;/* Auto-negotiation timeout current value */ - int PAutoNegTOCt; /* Auto-negotiation Timeout Counter */ - int PRxQSize; /* Port Rx Queue Size in kB */ - int PXSQSize; /* Port Synchronous Transmit Queue Size in kB */ - int PXAQSize; /* Port Asynchronous Transmit Queue Size in kB */ - SK_U32 PRxQRamStart; /* Receive Queue RAM Buffer Start Address */ - SK_U32 PRxQRamEnd; /* Receive Queue RAM Buffer End Address */ - SK_U32 PXsQRamStart; /* Sync Tx Queue RAM Buffer Start Address */ - SK_U32 PXsQRamEnd; /* Sync Tx Queue RAM Buffer End Address */ - SK_U32 PXaQRamStart; /* Async Tx Queue RAM Buffer Start Address */ - SK_U32 PXaQRamEnd; /* Async Tx Queue RAM Buffer End Address */ - SK_U32 PRxOverCnt; /* Receive Overflow Counter */ - int PRxQOff; /* Rx Queue Address Offset */ - int PXsQOff; /* Synchronous Tx Queue Address Offset */ - int PXaQOff; /* Asynchronous Tx Queue Address Offset */ - int PhyType; /* PHY used on this port */ - int PState; /* Port status (reset, stop, init, run) */ - SK_U16 PhyId1; /* PHY Id1 on this port */ - SK_U16 PhyAddr; /* MDIO/MDC PHY address */ - SK_U16 PIsave; /* Saved Interrupt status word */ - SK_U16 PSsave; /* Saved PHY status word */ - SK_U16 PGmANegAdv; /* Saved GPhy AutoNegAdvertisment register */ - SK_BOOL PHWLinkUp; /* The hardware Link is up (wiring) */ - SK_BOOL PLinkBroken; /* Is Link broken ? */ - SK_BOOL PCheckPar; /* Do we check for parity errors ? */ - SK_BOOL HalfDupTimerActive; - SK_U8 PLinkCap; /* Link Capabilities */ - SK_U8 PLinkModeConf; /* Link Mode configured */ - SK_U8 PLinkMode; /* Link Mode currently used */ - SK_U8 PLinkModeStatus;/* Link Mode Status */ - SK_U8 PLinkSpeedCap; /* Link Speed Capabilities(10/100/1000 Mbps) */ - SK_U8 PLinkSpeed; /* configured Link Speed (10/100/1000 Mbps) */ - SK_U8 PLinkSpeedUsed; /* current Link Speed (10/100/1000 Mbps) */ - SK_U8 PFlowCtrlCap; /* Flow Control Capabilities */ - SK_U8 PFlowCtrlMode; /* Flow Control Mode */ - SK_U8 PFlowCtrlStatus;/* Flow Control Status */ - SK_U8 PMSCap; /* Master/Slave Capabilities */ - SK_U8 PMSMode; /* Master/Slave Mode */ - SK_U8 PMSStatus; /* Master/Slave Status */ - SK_BOOL PAutoNegFail; /* Auto-negotiation fail flag */ - SK_U8 PLipaAutoNeg; /* Auto-negotiation possible with Link Partner */ - SK_U8 PCableLen; /* Cable Length */ - SK_U8 PMdiPairLen[4]; /* MDI[0..3] Pair Length */ - SK_U8 PMdiPairSts[4]; /* MDI[0..3] Pair Diagnostic Status */ - SK_U8 PPhyPowerState; /* PHY current power state */ - int PMacColThres; /* MAC Collision Threshold */ - int PMacJamLen; /* MAC Jam length */ - int PMacJamIpgVal; /* MAC Jam IPG */ - int PMacJamIpgData; /* MAC IPG Jam to Data */ - int PMacIpgData; /* MAC Data IPG */ - SK_BOOL PMacLimit4; /* reset collision counter and backoff algorithm */ -} SK_GEPORT; - -/* - * Gigabit Ethernet Initialization Struct - * (has to be included in the adapter context) - */ -typedef struct s_GeInit { - int GIChipId; /* Chip Identification Number */ - int GIChipRev; /* Chip Revision Number */ - SK_U8 GIPciHwRev; /* PCI HW Revision Number */ - SK_BOOL GIGenesis; /* Genesis adapter ? */ - SK_BOOL GIYukon; /* YUKON-A1/Bx chip */ - SK_BOOL GIYukonLite; /* YUKON-Lite chip */ - SK_BOOL GICopperType; /* Copper Type adapter ? */ - SK_BOOL GIPciSlot64; /* 64-bit PCI Slot */ - SK_BOOL GIPciClock66; /* 66 MHz PCI Clock */ - SK_BOOL GIVauxAvail; /* VAUX available (YUKON) */ - SK_BOOL GIYukon32Bit; /* 32-Bit YUKON adapter */ - SK_U16 GILedBlinkCtrl; /* LED Blink Control */ - int GIMacsFound; /* Number of MACs found on this adapter */ - int GIMacType; /* MAC Type used on this adapter */ - int GIHstClkFact; /* Host Clock Factor (62.5 / HstClk * 100) */ - int GIPortUsage; /* Driver Port Usage */ - int GILevel; /* Initialization Level completed */ - int GIRamSize; /* The RAM size of the adapter in kB */ - int GIWolOffs; /* WOL Register Offset (HW-Bug in Rev. A) */ - SK_U32 GIRamOffs; /* RAM Address Offset for addr calculation */ - SK_U32 GIPollTimerVal; /* Descr. Poll Timer Init Val (HstClk ticks) */ - SK_U32 GIValIrqMask; /* Value for Interrupt Mask */ - SK_U32 GITimeStampCnt; /* Time Stamp High Counter (YUKON only) */ - SK_GEPORT GP[SK_MAX_MACS];/* Port Dependent Information */ - SK_GEMACFUNC GIFunc; /* MAC depedent functions */ -} SK_GEINIT; - -/* - * Error numbers and messages for skxmac2.c and skgeinit.c - */ -#define SKERR_HWI_E001 (SK_ERRBASE_HWINIT) -#define SKERR_HWI_E001MSG "SkXmClrExactAddr() has got illegal parameters" -#define SKERR_HWI_E002 (SKERR_HWI_E001+1) -#define SKERR_HWI_E002MSG "SkGeInit(): Level 1 call missing" -#define SKERR_HWI_E003 (SKERR_HWI_E002+1) -#define SKERR_HWI_E003MSG "SkGeInit() called with illegal init Level" -#define SKERR_HWI_E004 (SKERR_HWI_E003+1) -#define SKERR_HWI_E004MSG "SkGeInitPort(): Queue Size illegal configured" -#define SKERR_HWI_E005 (SKERR_HWI_E004+1) -#define SKERR_HWI_E005MSG "SkGeInitPort(): cannot init running ports" -#define SKERR_HWI_E006 (SKERR_HWI_E005+1) -#define SKERR_HWI_E006MSG "SkGeMacInit(): PState does not match HW state" -#define SKERR_HWI_E007 (SKERR_HWI_E006+1) -#define SKERR_HWI_E007MSG "SkXmInitDupMd() called with invalid Dup Mode" -#define SKERR_HWI_E008 (SKERR_HWI_E007+1) -#define SKERR_HWI_E008MSG "SkXmSetRxCmd() called with invalid Mode" -#define SKERR_HWI_E009 (SKERR_HWI_E008+1) -#define SKERR_HWI_E009MSG "SkGeCfgSync() called although PXSQSize zero" -#define SKERR_HWI_E010 (SKERR_HWI_E009+1) -#define SKERR_HWI_E010MSG "SkGeCfgSync() called with invalid parameters" -#define SKERR_HWI_E011 (SKERR_HWI_E010+1) -#define SKERR_HWI_E011MSG "SkGeInitPort(): Receive Queue Size too small" -#define SKERR_HWI_E012 (SKERR_HWI_E011+1) -#define SKERR_HWI_E012MSG "SkGeInitPort(): invalid Queue Size specified" -#define SKERR_HWI_E013 (SKERR_HWI_E012+1) -#define SKERR_HWI_E013MSG "SkGeInitPort(): cfg changed for running queue" -#define SKERR_HWI_E014 (SKERR_HWI_E013+1) -#define SKERR_HWI_E014MSG "SkGeInitPort(): unknown GIPortUsage specified" -#define SKERR_HWI_E015 (SKERR_HWI_E014+1) -#define SKERR_HWI_E015MSG "Illegal Link mode parameter" -#define SKERR_HWI_E016 (SKERR_HWI_E015+1) -#define SKERR_HWI_E016MSG "Illegal Flow control mode parameter" -#define SKERR_HWI_E017 (SKERR_HWI_E016+1) -#define SKERR_HWI_E017MSG "Illegal value specified for GIPollTimerVal" -#define SKERR_HWI_E018 (SKERR_HWI_E017+1) -#define SKERR_HWI_E018MSG "FATAL: SkGeStopPort() does not terminate (Tx)" -#define SKERR_HWI_E019 (SKERR_HWI_E018+1) -#define SKERR_HWI_E019MSG "Illegal Speed parameter" -#define SKERR_HWI_E020 (SKERR_HWI_E019+1) -#define SKERR_HWI_E020MSG "Illegal Master/Slave parameter" -#define SKERR_HWI_E021 (SKERR_HWI_E020+1) -#define SKERR_HWI_E021MSG "MacUpdateStats(): cannot update statistic counter" -#define SKERR_HWI_E022 (SKERR_HWI_E021+1) -#define SKERR_HWI_E022MSG "MacStatistic(): illegal statistic base address" -#define SKERR_HWI_E023 (SKERR_HWI_E022+1) -#define SKERR_HWI_E023MSG "SkGeInitPort(): Transmit Queue Size too small" -#define SKERR_HWI_E024 (SKERR_HWI_E023+1) -#define SKERR_HWI_E024MSG "FATAL: SkGeStopPort() does not terminate (Rx)" -#define SKERR_HWI_E025 (SKERR_HWI_E024+1) -#define SKERR_HWI_E025MSG "" - -/* function prototypes ********************************************************/ - -#ifndef SK_KR_PROTO - -/* - * public functions in skgeinit.c - */ -extern void SkGePollTxD( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_BOOL PollTxD); - -extern void SkGeYellowLED( - SK_AC *pAC, - SK_IOC IoC, - int State); - -extern int SkGeCfgSync( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_U32 IntTime, - SK_U32 LimCount, - int SyncMode); - -extern void SkGeLoadLnkSyncCnt( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_U32 CntVal); - -extern void SkGeStopPort( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int Dir, - int RstMode); - -extern int SkGeInit( - SK_AC *pAC, - SK_IOC IoC, - int Level); - -extern void SkGeDeInit( - SK_AC *pAC, - SK_IOC IoC); - -extern int SkGeInitPort( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkGeXmitLED( - SK_AC *pAC, - SK_IOC IoC, - int Led, - int Mode); - -extern int SkGeInitAssignRamToQueues( - SK_AC *pAC, - int ActivePort, - SK_BOOL DualNet); - -/* - * public functions in skxmac2.c - */ -extern void SkMacRxTxDisable( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkMacSoftRst( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkMacHardRst( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkXmInitMac( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkGmInitMac( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkMacInitPhy( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_BOOL DoLoop); - -extern void SkMacIrqDisable( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkMacFlushTxFifo( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkMacIrq( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern int SkMacAutoNegDone( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkMacAutoNegLipaPhy( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_U16 IStatus); - -extern int SkMacRxTxEnable( - SK_AC *pAC, - SK_IOC IoC, - int Port); - -extern void SkMacPromiscMode( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_BOOL Enable); - -extern void SkMacHashing( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_BOOL Enable); - -extern void SkXmPhyRead( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int Addr, - SK_U16 SK_FAR *pVal); - -extern void SkXmPhyWrite( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int Addr, - SK_U16 Val); - -extern void SkGmPhyRead( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int Addr, - SK_U16 SK_FAR *pVal); - -extern void SkGmPhyWrite( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int Addr, - SK_U16 Val); - -extern void SkXmClrExactAddr( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int StartNum, - int StopNum); - -extern void SkXmAutoNegLipaXmac( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_U16 IStatus); - -extern int SkXmUpdateStats( - SK_AC *pAC, - SK_IOC IoC, - unsigned int Port); - -extern int SkGmUpdateStats( - SK_AC *pAC, - SK_IOC IoC, - unsigned int Port); - -extern int SkXmMacStatistic( - SK_AC *pAC, - SK_IOC IoC, - unsigned int Port, - SK_U16 StatAddr, - SK_U32 SK_FAR *pVal); - -extern int SkGmMacStatistic( - SK_AC *pAC, - SK_IOC IoC, - unsigned int Port, - SK_U16 StatAddr, - SK_U32 SK_FAR *pVal); - -extern int SkXmResetCounter( - SK_AC *pAC, - SK_IOC IoC, - unsigned int Port); - -extern int SkGmResetCounter( - SK_AC *pAC, - SK_IOC IoC, - unsigned int Port); - -extern int SkXmOverflowStatus( - SK_AC *pAC, - SK_IOC IoC, - unsigned int Port, - SK_U16 IStatus, - SK_U64 SK_FAR *pStatus); - -extern int SkGmOverflowStatus( - SK_AC *pAC, - SK_IOC IoC, - unsigned int Port, - SK_U16 MacStatus, - SK_U64 SK_FAR *pStatus); - -extern int SkGmCableDiagStatus( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_BOOL StartTest); - -#ifdef SK_DIAG -extern void SkGePhyRead( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int Addr, - SK_U16 *pVal); - -extern void SkGePhyWrite( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int Addr, - SK_U16 Val); - -extern void SkMacSetRxCmd( - SK_AC *pAC, - SK_IOC IoC, - int Port, - int Mode); -extern void SkMacCrcGener( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_BOOL Enable); -extern void SkMacTimeStamp( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_BOOL Enable); -extern void SkXmSendCont( - SK_AC *pAC, - SK_IOC IoC, - int Port, - SK_BOOL Enable); -#endif /* SK_DIAG */ - -#else /* SK_KR_PROTO */ - -/* - * public functions in skgeinit.c - */ -extern void SkGePollTxD(); -extern void SkGeYellowLED(); -extern int SkGeCfgSync(); -extern void SkGeLoadLnkSyncCnt(); -extern void SkGeStopPort(); -extern int SkGeInit(); -extern void SkGeDeInit(); -extern int SkGeInitPort(); -extern void SkGeXmitLED(); -extern int SkGeInitAssignRamToQueues(); - -/* - * public functions in skxmac2.c - */ -extern void SkMacRxTxDisable(); -extern void SkMacSoftRst(); -extern void SkMacHardRst(); -extern void SkMacInitPhy(); -extern int SkMacRxTxEnable(); -extern void SkMacPromiscMode(); -extern void SkMacHashing(); -extern void SkMacIrqDisable(); -extern void SkMacFlushTxFifo(); -extern void SkMacIrq(); -extern int SkMacAutoNegDone(); -extern void SkMacAutoNegLipaPhy(); -extern void SkXmInitMac(); -extern void SkXmPhyRead(); -extern void SkXmPhyWrite(); -extern void SkGmInitMac(); -extern void SkGmPhyRead(); -extern void SkGmPhyWrite(); -extern void SkXmClrExactAddr(); -extern void SkXmAutoNegLipaXmac(); -extern int SkXmUpdateStats(); -extern int SkGmUpdateStats(); -extern int SkXmMacStatistic(); -extern int SkGmMacStatistic(); -extern int SkXmResetCounter(); -extern int SkGmResetCounter(); -extern int SkXmOverflowStatus(); -extern int SkGmOverflowStatus(); -extern int SkGmCableDiagStatus(); - -#ifdef SK_DIAG -extern void SkGePhyRead(); -extern void SkGePhyWrite(); -extern void SkMacSetRxCmd(); -extern void SkMacCrcGener(); -extern void SkMacTimeStamp(); -extern void SkXmSendCont(); -#endif /* SK_DIAG */ - -#endif /* SK_KR_PROTO */ - -#ifdef __cplusplus -} -#endif /* __cplusplus */ - -#endif /* __INC_SKGEINIT_H_ */ diff --git a/drivers/net/sk98lin/h/skgepnm2.h b/drivers/net/sk98lin/h/skgepnm2.h deleted file mode 100644 index ddd304f1a48b..000000000000 --- a/drivers/net/sk98lin/h/skgepnm2.h +++ /dev/null @@ -1,334 +0,0 @@ -/***************************************************************************** - * - * Name: skgepnm2.h - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.36 $ - * Date: $Date: 2003/05/23 12:45:13 $ - * Purpose: Defines for Private Network Management Interface - * - ****************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef _SKGEPNM2_H_ -#define _SKGEPNM2_H_ - -/* - * General definitions - */ -#define SK_PNMI_CHIPSET_XMAC 1 /* XMAC11800FP */ -#define SK_PNMI_CHIPSET_YUKON 2 /* YUKON */ - -#define SK_PNMI_BUS_PCI 1 /* PCI bus*/ - -/* - * Actions - */ -#define SK_PNMI_ACT_IDLE 1 -#define SK_PNMI_ACT_RESET 2 -#define SK_PNMI_ACT_SELFTEST 3 -#define SK_PNMI_ACT_RESETCNT 4 - -/* - * VPD releated defines - */ - -#define SK_PNMI_VPD_RW 1 -#define SK_PNMI_VPD_RO 2 - -#define SK_PNMI_VPD_OK 0 -#define SK_PNMI_VPD_NOTFOUND 1 -#define SK_PNMI_VPD_CUT 2 -#define SK_PNMI_VPD_TIMEOUT 3 -#define SK_PNMI_VPD_FULL 4 -#define SK_PNMI_VPD_NOWRITE 5 -#define SK_PNMI_VPD_FATAL 6 - -#define SK_PNMI_VPD_IGNORE 0 -#define SK_PNMI_VPD_CREATE 1 -#define SK_PNMI_VPD_DELETE 2 - - -/* - * RLMT related defines - */ -#define SK_PNMI_DEF_RLMT_CHG_THRES 240 /* 4 changes per minute */ - - -/* - * VCT internal status values - */ -#define SK_PNMI_VCT_PENDING 32 -#define SK_PNMI_VCT_TEST_DONE 64 -#define SK_PNMI_VCT_LINK 128 - -/* - * Internal table definitions - */ -#define SK_PNMI_GET 0 -#define SK_PNMI_PRESET 1 -#define SK_PNMI_SET 2 - -#define SK_PNMI_RO 0 -#define SK_PNMI_RW 1 -#define SK_PNMI_WO 2 - -typedef struct s_OidTabEntry { - SK_U32 Id; - SK_U32 InstanceNo; - unsigned int StructSize; - unsigned int Offset; - int Access; - int (* Func)(SK_AC *pAc, SK_IOC pIo, int action, - SK_U32 Id, char* pBuf, unsigned int* pLen, - SK_U32 Instance, unsigned int TableIndex, - SK_U32 NetNumber); - SK_U16 Param; -} SK_PNMI_TAB_ENTRY; - - -/* - * Trap lengths - */ -#define SK_PNMI_TRAP_SIMPLE_LEN 17 -#define SK_PNMI_TRAP_SENSOR_LEN_BASE 46 -#define SK_PNMI_TRAP_RLMT_CHANGE_LEN 23 -#define SK_PNMI_TRAP_RLMT_PORT_LEN 23 - -/* - * Number of MAC types supported - */ -#define SK_PNMI_MAC_TYPES (SK_MAC_GMAC + 1) - -/* - * MAC statistic data list (overall set for MAC types used) - */ -enum SK_MACSTATS { - SK_PNMI_HTX = 0, - SK_PNMI_HTX_OCTET, - SK_PNMI_HTX_OCTETHIGH = SK_PNMI_HTX_OCTET, - SK_PNMI_HTX_OCTETLOW, - SK_PNMI_HTX_BROADCAST, - SK_PNMI_HTX_MULTICAST, - SK_PNMI_HTX_UNICAST, - SK_PNMI_HTX_BURST, - SK_PNMI_HTX_PMACC, - SK_PNMI_HTX_MACC, - SK_PNMI_HTX_COL, - SK_PNMI_HTX_SINGLE_COL, - SK_PNMI_HTX_MULTI_COL, - SK_PNMI_HTX_EXCESS_COL, - SK_PNMI_HTX_LATE_COL, - SK_PNMI_HTX_DEFFERAL, - SK_PNMI_HTX_EXCESS_DEF, - SK_PNMI_HTX_UNDERRUN, - SK_PNMI_HTX_CARRIER, - SK_PNMI_HTX_UTILUNDER, - SK_PNMI_HTX_UTILOVER, - SK_PNMI_HTX_64, - SK_PNMI_HTX_127, - SK_PNMI_HTX_255, - SK_PNMI_HTX_511, - SK_PNMI_HTX_1023, - SK_PNMI_HTX_MAX, - SK_PNMI_HTX_LONGFRAMES, - SK_PNMI_HTX_SYNC, - SK_PNMI_HTX_SYNC_OCTET, - SK_PNMI_HTX_RESERVED, - - SK_PNMI_HRX, - SK_PNMI_HRX_OCTET, - SK_PNMI_HRX_OCTETHIGH = SK_PNMI_HRX_OCTET, - SK_PNMI_HRX_OCTETLOW, - SK_PNMI_HRX_BADOCTET, - SK_PNMI_HRX_BADOCTETHIGH = SK_PNMI_HRX_BADOCTET, - SK_PNMI_HRX_BADOCTETLOW, - SK_PNMI_HRX_BROADCAST, - SK_PNMI_HRX_MULTICAST, - SK_PNMI_HRX_UNICAST, - SK_PNMI_HRX_PMACC, - SK_PNMI_HRX_MACC, - SK_PNMI_HRX_PMACC_ERR, - SK_PNMI_HRX_MACC_UNKWN, - SK_PNMI_HRX_BURST, - SK_PNMI_HRX_MISSED, - SK_PNMI_HRX_FRAMING, - SK_PNMI_HRX_UNDERSIZE, - SK_PNMI_HRX_OVERFLOW, - SK_PNMI_HRX_JABBER, - SK_PNMI_HRX_CARRIER, - SK_PNMI_HRX_IRLENGTH, - SK_PNMI_HRX_SYMBOL, - SK_PNMI_HRX_SHORTS, - SK_PNMI_HRX_RUNT, - SK_PNMI_HRX_TOO_LONG, - SK_PNMI_HRX_FCS, - SK_PNMI_HRX_CEXT, - SK_PNMI_HRX_UTILUNDER, - SK_PNMI_HRX_UTILOVER, - SK_PNMI_HRX_64, - SK_PNMI_HRX_127, - SK_PNMI_HRX_255, - SK_PNMI_HRX_511, - SK_PNMI_HRX_1023, - SK_PNMI_HRX_MAX, - SK_PNMI_HRX_LONGFRAMES, - - SK_PNMI_HRX_RESERVED, - - SK_PNMI_MAX_IDX /* NOTE: Ensure SK_PNMI_CNT_NO is set to this value */ -}; - -/* - * MAC specific data - */ -typedef struct s_PnmiStatAddr { - SK_U16 Reg; /* MAC register containing the value */ - SK_BOOL GetOffset; /* TRUE: Offset managed by PNMI (call GetStatVal())*/ -} SK_PNMI_STATADDR; - - -/* - * SK_PNMI_STRUCT_DATA copy offset evaluation macros - */ -#define SK_PNMI_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_STRUCT_DATA *)0)->e)) -#define SK_PNMI_MAI_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_STRUCT_DATA *)0)->e)) -#define SK_PNMI_VPD_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_VPD *)0)->e)) -#define SK_PNMI_SEN_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_SENSOR *)0)->e)) -#define SK_PNMI_CHK_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_CHECKSUM *)0)->e)) -#define SK_PNMI_STA_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_STAT *)0)->e)) -#define SK_PNMI_CNF_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_CONF *)0)->e)) -#define SK_PNMI_RLM_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_RLMT *)0)->e)) -#define SK_PNMI_MON_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_RLMT_MONITOR *)0)->e)) -#define SK_PNMI_TRP_OFF(e) ((SK_U32)(SK_UPTR)&(((SK_PNMI_TRAP *)0)->e)) - -#define SK_PNMI_SET_STAT(b,s,o) {SK_U32 Val32; char *pVal; \ - Val32 = (s); \ - pVal = (char *)(b) + ((SK_U32)(SK_UPTR) \ - &(((SK_PNMI_STRUCT_DATA *)0)-> \ - ReturnStatus.ErrorStatus)); \ - SK_PNMI_STORE_U32(pVal, Val32); \ - Val32 = (o); \ - pVal = (char *)(b) + ((SK_U32)(SK_UPTR) \ - &(((SK_PNMI_STRUCT_DATA *)0)-> \ - ReturnStatus.ErrorOffset)); \ - SK_PNMI_STORE_U32(pVal, Val32);} - -/* - * Time macros - */ -#ifndef SK_PNMI_HUNDREDS_SEC -#if SK_TICKS_PER_SEC == 100 -#define SK_PNMI_HUNDREDS_SEC(t) (t) -#else -#define SK_PNMI_HUNDREDS_SEC(t) (((t) * 100) / (SK_TICKS_PER_SEC)) -#endif /* !SK_TICKS_PER_SEC */ -#endif /* !SK_PNMI_HUNDREDS_SEC */ - -/* - * Macros to work around alignment problems - */ -#ifndef SK_PNMI_STORE_U16 -#define SK_PNMI_STORE_U16(p,v) {*(char *)(p) = *((char *)&(v)); \ - *((char *)(p) + 1) = \ - *(((char *)&(v)) + 1);} -#endif - -#ifndef SK_PNMI_STORE_U32 -#define SK_PNMI_STORE_U32(p,v) {*(char *)(p) = *((char *)&(v)); \ - *((char *)(p) + 1) = \ - *(((char *)&(v)) + 1); \ - *((char *)(p) + 2) = \ - *(((char *)&(v)) + 2); \ - *((char *)(p) + 3) = \ - *(((char *)&(v)) + 3);} -#endif - -#ifndef SK_PNMI_STORE_U64 -#define SK_PNMI_STORE_U64(p,v) {*(char *)(p) = *((char *)&(v)); \ - *((char *)(p) + 1) = \ - *(((char *)&(v)) + 1); \ - *((char *)(p) + 2) = \ - *(((char *)&(v)) + 2); \ - *((char *)(p) + 3) = \ - *(((char *)&(v)) + 3); \ - *((char *)(p) + 4) = \ - *(((char *)&(v)) + 4); \ - *((char *)(p) + 5) = \ - *(((char *)&(v)) + 5); \ - *((char *)(p) + 6) = \ - *(((char *)&(v)) + 6); \ - *((char *)(p) + 7) = \ - *(((char *)&(v)) + 7);} -#endif - -#ifndef SK_PNMI_READ_U16 -#define SK_PNMI_READ_U16(p,v) {*((char *)&(v)) = *(char *)(p); \ - *(((char *)&(v)) + 1) = \ - *((char *)(p) + 1);} -#endif - -#ifndef SK_PNMI_READ_U32 -#define SK_PNMI_READ_U32(p,v) {*((char *)&(v)) = *(char *)(p); \ - *(((char *)&(v)) + 1) = \ - *((char *)(p) + 1); \ - *(((char *)&(v)) + 2) = \ - *((char *)(p) + 2); \ - *(((char *)&(v)) + 3) = \ - *((char *)(p) + 3);} -#endif - -#ifndef SK_PNMI_READ_U64 -#define SK_PNMI_READ_U64(p,v) {*((char *)&(v)) = *(char *)(p); \ - *(((char *)&(v)) + 1) = \ - *((char *)(p) + 1); \ - *(((char *)&(v)) + 2) = \ - *((char *)(p) + 2); \ - *(((char *)&(v)) + 3) = \ - *((char *)(p) + 3); \ - *(((char *)&(v)) + 4) = \ - *((char *)(p) + 4); \ - *(((char *)&(v)) + 5) = \ - *((char *)(p) + 5); \ - *(((char *)&(v)) + 6) = \ - *((char *)(p) + 6); \ - *(((char *)&(v)) + 7) = \ - *((char *)(p) + 7);} -#endif - -/* - * Macros for Debug - */ -#ifdef DEBUG - -#define SK_PNMI_CHECKFLAGS(vSt) {if (pAC->Pnmi.MacUpdatedFlag > 0 || \ - pAC->Pnmi.RlmtUpdatedFlag > 0 || \ - pAC->Pnmi.SirqUpdatedFlag > 0) { \ - SK_DBG_MSG(pAC, \ - SK_DBGMOD_PNMI, \ - SK_DBGCAT_CTRL, \ - ("PNMI: ERR: %s MacUFlag=%d, RlmtUFlag=%d, SirqUFlag=%d\n", \ - vSt, \ - pAC->Pnmi.MacUpdatedFlag, \ - pAC->Pnmi.RlmtUpdatedFlag, \ - pAC->Pnmi.SirqUpdatedFlag))}} - -#else /* !DEBUG */ - -#define SK_PNMI_CHECKFLAGS(vSt) /* Nothing */ - -#endif /* !DEBUG */ - -#endif /* _SKGEPNM2_H_ */ diff --git a/drivers/net/sk98lin/h/skgepnmi.h b/drivers/net/sk98lin/h/skgepnmi.h deleted file mode 100644 index 1ed214ccb253..000000000000 --- a/drivers/net/sk98lin/h/skgepnmi.h +++ /dev/null @@ -1,962 +0,0 @@ -/***************************************************************************** - * - * Name: skgepnmi.h - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.62 $ - * Date: $Date: 2003/08/15 12:31:52 $ - * Purpose: Defines for Private Network Management Interface - * - ****************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef _SKGEPNMI_H_ -#define _SKGEPNMI_H_ - -/* - * Include dependencies - */ -#include "h/sktypes.h" -#include "h/skerror.h" -#include "h/sktimer.h" -#include "h/ski2c.h" -#include "h/skaddr.h" -#include "h/skrlmt.h" -#include "h/skvpd.h" - -/* - * Management Database Version - */ -#define SK_PNMI_MDB_VERSION 0x00030001 /* 3.1 */ - - -/* - * Event definitions - */ -#define SK_PNMI_EVT_SIRQ_OVERFLOW 1 /* Counter overflow */ -#define SK_PNMI_EVT_SEN_WAR_LOW 2 /* Lower war thres exceeded */ -#define SK_PNMI_EVT_SEN_WAR_UPP 3 /* Upper war thres exceeded */ -#define SK_PNMI_EVT_SEN_ERR_LOW 4 /* Lower err thres exceeded */ -#define SK_PNMI_EVT_SEN_ERR_UPP 5 /* Upper err thres exceeded */ -#define SK_PNMI_EVT_CHG_EST_TIMER 6 /* Timer event for RLMT Chg */ -#define SK_PNMI_EVT_UTILIZATION_TIMER 7 /* Timer event for Utiliza. */ -#define SK_PNMI_EVT_CLEAR_COUNTER 8 /* Clear statistic counters */ -#define SK_PNMI_EVT_XMAC_RESET 9 /* XMAC will be reset */ - -#define SK_PNMI_EVT_RLMT_PORT_UP 10 /* Port came logically up */ -#define SK_PNMI_EVT_RLMT_PORT_DOWN 11 /* Port went logically down */ -#define SK_PNMI_EVT_RLMT_SEGMENTATION 13 /* Two SP root bridges found */ -#define SK_PNMI_EVT_RLMT_ACTIVE_DOWN 14 /* Port went logically down */ -#define SK_PNMI_EVT_RLMT_ACTIVE_UP 15 /* Port came logically up */ -#define SK_PNMI_EVT_RLMT_SET_NETS 16 /* 1. Parameter is number of nets - 1 = single net; 2 = dual net */ -#define SK_PNMI_EVT_VCT_RESET 17 /* VCT port reset timer event started with SET. */ - - -/* - * Return values - */ -#define SK_PNMI_ERR_OK 0 -#define SK_PNMI_ERR_GENERAL 1 -#define SK_PNMI_ERR_TOO_SHORT 2 -#define SK_PNMI_ERR_BAD_VALUE 3 -#define SK_PNMI_ERR_READ_ONLY 4 -#define SK_PNMI_ERR_UNKNOWN_OID 5 -#define SK_PNMI_ERR_UNKNOWN_INST 6 -#define SK_PNMI_ERR_UNKNOWN_NET 7 -#define SK_PNMI_ERR_NOT_SUPPORTED 10 - - -/* - * Return values of driver reset function SK_DRIVER_RESET() and - * driver event function SK_DRIVER_EVENT() - */ -#define SK_PNMI_ERR_OK 0 -#define SK_PNMI_ERR_FAIL 1 - - -/* - * Return values of driver test function SK_DRIVER_SELFTEST() - */ -#define SK_PNMI_TST_UNKNOWN (1 << 0) -#define SK_PNMI_TST_TRANCEIVER (1 << 1) -#define SK_PNMI_TST_ASIC (1 << 2) -#define SK_PNMI_TST_SENSOR (1 << 3) -#define SK_PNMI_TST_POWERMGMT (1 << 4) -#define SK_PNMI_TST_PCI (1 << 5) -#define SK_PNMI_TST_MAC (1 << 6) - - -/* - * RLMT specific definitions - */ -#define SK_PNMI_RLMT_STATUS_STANDBY 1 -#define SK_PNMI_RLMT_STATUS_ACTIVE 2 -#define SK_PNMI_RLMT_STATUS_ERROR 3 - -#define SK_PNMI_RLMT_LSTAT_PHY_DOWN 1 -#define SK_PNMI_RLMT_LSTAT_AUTONEG 2 -#define SK_PNMI_RLMT_LSTAT_LOG_DOWN 3 -#define SK_PNMI_RLMT_LSTAT_LOG_UP 4 -#define SK_PNMI_RLMT_LSTAT_INDETERMINATED 5 - -#define SK_PNMI_RLMT_MODE_CHK_LINK (SK_RLMT_CHECK_LINK) -#define SK_PNMI_RLMT_MODE_CHK_RX (SK_RLMT_CHECK_LOC_LINK) -#define SK_PNMI_RLMT_MODE_CHK_SPT (SK_RLMT_CHECK_SEG) -/* #define SK_PNMI_RLMT_MODE_CHK_EX */ - -/* - * OID definition - */ -#ifndef _NDIS_ /* Check, whether NDIS already included OIDs */ - -#define OID_GEN_XMIT_OK 0x00020101 -#define OID_GEN_RCV_OK 0x00020102 -#define OID_GEN_XMIT_ERROR 0x00020103 -#define OID_GEN_RCV_ERROR 0x00020104 -#define OID_GEN_RCV_NO_BUFFER 0x00020105 - -/* #define OID_GEN_DIRECTED_BYTES_XMIT 0x00020201 */ -#define OID_GEN_DIRECTED_FRAMES_XMIT 0x00020202 -/* #define OID_GEN_MULTICAST_BYTES_XMIT 0x00020203 */ -#define OID_GEN_MULTICAST_FRAMES_XMIT 0x00020204 -/* #define OID_GEN_BROADCAST_BYTES_XMIT 0x00020205 */ -#define OID_GEN_BROADCAST_FRAMES_XMIT 0x00020206 -/* #define OID_GEN_DIRECTED_BYTES_RCV 0x00020207 */ -#define OID_GEN_DIRECTED_FRAMES_RCV 0x00020208 -/* #define OID_GEN_MULTICAST_BYTES_RCV 0x00020209 */ -#define OID_GEN_MULTICAST_FRAMES_RCV 0x0002020A -/* #define OID_GEN_BROADCAST_BYTES_RCV 0x0002020B */ -#define OID_GEN_BROADCAST_FRAMES_RCV 0x0002020C -#define OID_GEN_RCV_CRC_ERROR 0x0002020D -#define OID_GEN_TRANSMIT_QUEUE_LENGTH 0x0002020E - -#define OID_802_3_PERMANENT_ADDRESS 0x01010101 -#define OID_802_3_CURRENT_ADDRESS 0x01010102 -/* #define OID_802_3_MULTICAST_LIST 0x01010103 */ -/* #define OID_802_3_MAXIMUM_LIST_SIZE 0x01010104 */ -/* #define OID_802_3_MAC_OPTIONS 0x01010105 */ - -#define OID_802_3_RCV_ERROR_ALIGNMENT 0x01020101 -#define OID_802_3_XMIT_ONE_COLLISION 0x01020102 -#define OID_802_3_XMIT_MORE_COLLISIONS 0x01020103 -#define OID_802_3_XMIT_DEFERRED 0x01020201 -#define OID_802_3_XMIT_MAX_COLLISIONS 0x01020202 -#define OID_802_3_RCV_OVERRUN 0x01020203 -#define OID_802_3_XMIT_UNDERRUN 0x01020204 -#define OID_802_3_XMIT_TIMES_CRS_LOST 0x01020206 -#define OID_802_3_XMIT_LATE_COLLISIONS 0x01020207 - -/* - * PnP and PM OIDs - */ -#ifdef SK_POWER_MGMT -#define OID_PNP_CAPABILITIES 0xFD010100 -#define OID_PNP_SET_POWER 0xFD010101 -#define OID_PNP_QUERY_POWER 0xFD010102 -#define OID_PNP_ADD_WAKE_UP_PATTERN 0xFD010103 -#define OID_PNP_REMOVE_WAKE_UP_PATTERN 0xFD010104 -#define OID_PNP_ENABLE_WAKE_UP 0xFD010106 -#endif /* SK_POWER_MGMT */ - -#endif /* _NDIS_ */ - -#define OID_SKGE_MDB_VERSION 0xFF010100 -#define OID_SKGE_SUPPORTED_LIST 0xFF010101 -#define OID_SKGE_VPD_FREE_BYTES 0xFF010102 -#define OID_SKGE_VPD_ENTRIES_LIST 0xFF010103 -#define OID_SKGE_VPD_ENTRIES_NUMBER 0xFF010104 -#define OID_SKGE_VPD_KEY 0xFF010105 -#define OID_SKGE_VPD_VALUE 0xFF010106 -#define OID_SKGE_VPD_ACCESS 0xFF010107 -#define OID_SKGE_VPD_ACTION 0xFF010108 - -#define OID_SKGE_PORT_NUMBER 0xFF010110 -#define OID_SKGE_DEVICE_TYPE 0xFF010111 -#define OID_SKGE_DRIVER_DESCR 0xFF010112 -#define OID_SKGE_DRIVER_VERSION 0xFF010113 -#define OID_SKGE_HW_DESCR 0xFF010114 -#define OID_SKGE_HW_VERSION 0xFF010115 -#define OID_SKGE_CHIPSET 0xFF010116 -#define OID_SKGE_ACTION 0xFF010117 -#define OID_SKGE_RESULT 0xFF010118 -#define OID_SKGE_BUS_TYPE 0xFF010119 -#define OID_SKGE_BUS_SPEED 0xFF01011A -#define OID_SKGE_BUS_WIDTH 0xFF01011B -/* 0xFF01011C unused */ -#define OID_SKGE_DIAG_ACTION 0xFF01011D -#define OID_SKGE_DIAG_RESULT 0xFF01011E -#define OID_SKGE_MTU 0xFF01011F -#define OID_SKGE_PHYS_CUR_ADDR 0xFF010120 -#define OID_SKGE_PHYS_FAC_ADDR 0xFF010121 -#define OID_SKGE_PMD 0xFF010122 -#define OID_SKGE_CONNECTOR 0xFF010123 -#define OID_SKGE_LINK_CAP 0xFF010124 -#define OID_SKGE_LINK_MODE 0xFF010125 -#define OID_SKGE_LINK_MODE_STATUS 0xFF010126 -#define OID_SKGE_LINK_STATUS 0xFF010127 -#define OID_SKGE_FLOWCTRL_CAP 0xFF010128 -#define OID_SKGE_FLOWCTRL_MODE 0xFF010129 -#define OID_SKGE_FLOWCTRL_STATUS 0xFF01012A -#define OID_SKGE_PHY_OPERATION_CAP 0xFF01012B -#define OID_SKGE_PHY_OPERATION_MODE 0xFF01012C -#define OID_SKGE_PHY_OPERATION_STATUS 0xFF01012D -#define OID_SKGE_MULTICAST_LIST 0xFF01012E -#define OID_SKGE_CURRENT_PACKET_FILTER 0xFF01012F - -#define OID_SKGE_TRAP 0xFF010130 -#define OID_SKGE_TRAP_NUMBER 0xFF010131 - -#define OID_SKGE_RLMT_MODE 0xFF010140 -#define OID_SKGE_RLMT_PORT_NUMBER 0xFF010141 -#define OID_SKGE_RLMT_PORT_ACTIVE 0xFF010142 -#define OID_SKGE_RLMT_PORT_PREFERRED 0xFF010143 -#define OID_SKGE_INTERMEDIATE_SUPPORT 0xFF010160 - -#define OID_SKGE_SPEED_CAP 0xFF010170 -#define OID_SKGE_SPEED_MODE 0xFF010171 -#define OID_SKGE_SPEED_STATUS 0xFF010172 - -#define OID_SKGE_BOARDLEVEL 0xFF010180 - -#define OID_SKGE_SENSOR_NUMBER 0xFF020100 -#define OID_SKGE_SENSOR_INDEX 0xFF020101 -#define OID_SKGE_SENSOR_DESCR 0xFF020102 -#define OID_SKGE_SENSOR_TYPE 0xFF020103 -#define OID_SKGE_SENSOR_VALUE 0xFF020104 -#define OID_SKGE_SENSOR_WAR_THRES_LOW 0xFF020105 -#define OID_SKGE_SENSOR_WAR_THRES_UPP 0xFF020106 -#define OID_SKGE_SENSOR_ERR_THRES_LOW 0xFF020107 -#define OID_SKGE_SENSOR_ERR_THRES_UPP 0xFF020108 -#define OID_SKGE_SENSOR_STATUS 0xFF020109 -#define OID_SKGE_SENSOR_WAR_CTS 0xFF02010A -#define OID_SKGE_SENSOR_ERR_CTS 0xFF02010B -#define OID_SKGE_SENSOR_WAR_TIME 0xFF02010C -#define OID_SKGE_SENSOR_ERR_TIME 0xFF02010D - -#define OID_SKGE_CHKSM_NUMBER 0xFF020110 -#define OID_SKGE_CHKSM_RX_OK_CTS 0xFF020111 -#define OID_SKGE_CHKSM_RX_UNABLE_CTS 0xFF020112 -#define OID_SKGE_CHKSM_RX_ERR_CTS 0xFF020113 -#define OID_SKGE_CHKSM_TX_OK_CTS 0xFF020114 -#define OID_SKGE_CHKSM_TX_UNABLE_CTS 0xFF020115 - -#define OID_SKGE_STAT_TX 0xFF020120 -#define OID_SKGE_STAT_TX_OCTETS 0xFF020121 -#define OID_SKGE_STAT_TX_BROADCAST 0xFF020122 -#define OID_SKGE_STAT_TX_MULTICAST 0xFF020123 -#define OID_SKGE_STAT_TX_UNICAST 0xFF020124 -#define OID_SKGE_STAT_TX_LONGFRAMES 0xFF020125 -#define OID_SKGE_STAT_TX_BURST 0xFF020126 -#define OID_SKGE_STAT_TX_PFLOWC 0xFF020127 -#define OID_SKGE_STAT_TX_FLOWC 0xFF020128 -#define OID_SKGE_STAT_TX_SINGLE_COL 0xFF020129 -#define OID_SKGE_STAT_TX_MULTI_COL 0xFF02012A -#define OID_SKGE_STAT_TX_EXCESS_COL 0xFF02012B -#define OID_SKGE_STAT_TX_LATE_COL 0xFF02012C -#define OID_SKGE_STAT_TX_DEFFERAL 0xFF02012D -#define OID_SKGE_STAT_TX_EXCESS_DEF 0xFF02012E -#define OID_SKGE_STAT_TX_UNDERRUN 0xFF02012F -#define OID_SKGE_STAT_TX_CARRIER 0xFF020130 -/* #define OID_SKGE_STAT_TX_UTIL 0xFF020131 */ -#define OID_SKGE_STAT_TX_64 0xFF020132 -#define OID_SKGE_STAT_TX_127 0xFF020133 -#define OID_SKGE_STAT_TX_255 0xFF020134 -#define OID_SKGE_STAT_TX_511 0xFF020135 -#define OID_SKGE_STAT_TX_1023 0xFF020136 -#define OID_SKGE_STAT_TX_MAX 0xFF020137 -#define OID_SKGE_STAT_TX_SYNC 0xFF020138 -#define OID_SKGE_STAT_TX_SYNC_OCTETS 0xFF020139 -#define OID_SKGE_STAT_RX 0xFF02013A -#define OID_SKGE_STAT_RX_OCTETS 0xFF02013B -#define OID_SKGE_STAT_RX_BROADCAST 0xFF02013C -#define OID_SKGE_STAT_RX_MULTICAST 0xFF02013D -#define OID_SKGE_STAT_RX_UNICAST 0xFF02013E -#define OID_SKGE_STAT_RX_PFLOWC 0xFF02013F -#define OID_SKGE_STAT_RX_FLOWC 0xFF020140 -#define OID_SKGE_STAT_RX_PFLOWC_ERR 0xFF020141 -#define OID_SKGE_STAT_RX_FLOWC_UNKWN 0xFF020142 -#define OID_SKGE_STAT_RX_BURST 0xFF020143 -#define OID_SKGE_STAT_RX_MISSED 0xFF020144 -#define OID_SKGE_STAT_RX_FRAMING 0xFF020145 -#define OID_SKGE_STAT_RX_OVERFLOW 0xFF020146 -#define OID_SKGE_STAT_RX_JABBER 0xFF020147 -#define OID_SKGE_STAT_RX_CARRIER 0xFF020148 -#define OID_SKGE_STAT_RX_IR_LENGTH 0xFF020149 -#define OID_SKGE_STAT_RX_SYMBOL 0xFF02014A -#define OID_SKGE_STAT_RX_SHORTS 0xFF02014B -#define OID_SKGE_STAT_RX_RUNT 0xFF02014C -#define OID_SKGE_STAT_RX_CEXT 0xFF02014D -#define OID_SKGE_STAT_RX_TOO_LONG 0xFF02014E -#define OID_SKGE_STAT_RX_FCS 0xFF02014F -/* #define OID_SKGE_STAT_RX_UTIL 0xFF020150 */ -#define OID_SKGE_STAT_RX_64 0xFF020151 -#define OID_SKGE_STAT_RX_127 0xFF020152 -#define OID_SKGE_STAT_RX_255 0xFF020153 -#define OID_SKGE_STAT_RX_511 0xFF020154 -#define OID_SKGE_STAT_RX_1023 0xFF020155 -#define OID_SKGE_STAT_RX_MAX 0xFF020156 -#define OID_SKGE_STAT_RX_LONGFRAMES 0xFF020157 - -#define OID_SKGE_RLMT_CHANGE_CTS 0xFF020160 -#define OID_SKGE_RLMT_CHANGE_TIME 0xFF020161 -#define OID_SKGE_RLMT_CHANGE_ESTIM 0xFF020162 -#define OID_SKGE_RLMT_CHANGE_THRES 0xFF020163 - -#define OID_SKGE_RLMT_PORT_INDEX 0xFF020164 -#define OID_SKGE_RLMT_STATUS 0xFF020165 -#define OID_SKGE_RLMT_TX_HELLO_CTS 0xFF020166 -#define OID_SKGE_RLMT_RX_HELLO_CTS 0xFF020167 -#define OID_SKGE_RLMT_TX_SP_REQ_CTS 0xFF020168 -#define OID_SKGE_RLMT_RX_SP_CTS 0xFF020169 - -#define OID_SKGE_RLMT_MONITOR_NUMBER 0xFF010150 -#define OID_SKGE_RLMT_MONITOR_INDEX 0xFF010151 -#define OID_SKGE_RLMT_MONITOR_ADDR 0xFF010152 -#define OID_SKGE_RLMT_MONITOR_ERRS 0xFF010153 -#define OID_SKGE_RLMT_MONITOR_TIMESTAMP 0xFF010154 -#define OID_SKGE_RLMT_MONITOR_ADMIN 0xFF010155 - -#define OID_SKGE_TX_SW_QUEUE_LEN 0xFF020170 -#define OID_SKGE_TX_SW_QUEUE_MAX 0xFF020171 -#define OID_SKGE_TX_RETRY 0xFF020172 -#define OID_SKGE_RX_INTR_CTS 0xFF020173 -#define OID_SKGE_TX_INTR_CTS 0xFF020174 -#define OID_SKGE_RX_NO_BUF_CTS 0xFF020175 -#define OID_SKGE_TX_NO_BUF_CTS 0xFF020176 -#define OID_SKGE_TX_USED_DESCR_NO 0xFF020177 -#define OID_SKGE_RX_DELIVERED_CTS 0xFF020178 -#define OID_SKGE_RX_OCTETS_DELIV_CTS 0xFF020179 -#define OID_SKGE_RX_HW_ERROR_CTS 0xFF02017A -#define OID_SKGE_TX_HW_ERROR_CTS 0xFF02017B -#define OID_SKGE_IN_ERRORS_CTS 0xFF02017C -#define OID_SKGE_OUT_ERROR_CTS 0xFF02017D -#define OID_SKGE_ERR_RECOVERY_CTS 0xFF02017E -#define OID_SKGE_SYSUPTIME 0xFF02017F - -#define OID_SKGE_ALL_DATA 0xFF020190 - -/* Defines for VCT. */ -#define OID_SKGE_VCT_GET 0xFF020200 -#define OID_SKGE_VCT_SET 0xFF020201 -#define OID_SKGE_VCT_STATUS 0xFF020202 - -#ifdef SK_DIAG_SUPPORT -/* Defines for driver DIAG mode. */ -#define OID_SKGE_DIAG_MODE 0xFF020204 -#endif /* SK_DIAG_SUPPORT */ - -/* New OIDs */ -#define OID_SKGE_DRIVER_RELDATE 0xFF020210 -#define OID_SKGE_DRIVER_FILENAME 0xFF020211 -#define OID_SKGE_CHIPID 0xFF020212 -#define OID_SKGE_RAMSIZE 0xFF020213 -#define OID_SKGE_VAUXAVAIL 0xFF020214 -#define OID_SKGE_PHY_TYPE 0xFF020215 -#define OID_SKGE_PHY_LP_MODE 0xFF020216 - -/* VCT struct to store a backup copy of VCT data after a port reset. */ -typedef struct s_PnmiVct { - SK_U8 VctStatus; - SK_U8 PCableLen; - SK_U32 PMdiPairLen[4]; - SK_U8 PMdiPairSts[4]; -} SK_PNMI_VCT; - - -/* VCT status values (to be given to CPA via OID_SKGE_VCT_STATUS). */ -#define SK_PNMI_VCT_NONE 0 -#define SK_PNMI_VCT_OLD_VCT_DATA 1 -#define SK_PNMI_VCT_NEW_VCT_DATA 2 -#define SK_PNMI_VCT_OLD_DSP_DATA 4 -#define SK_PNMI_VCT_NEW_DSP_DATA 8 -#define SK_PNMI_VCT_RUNNING 16 - - -/* VCT cable test status. */ -#define SK_PNMI_VCT_NORMAL_CABLE 0 -#define SK_PNMI_VCT_SHORT_CABLE 1 -#define SK_PNMI_VCT_OPEN_CABLE 2 -#define SK_PNMI_VCT_TEST_FAIL 3 -#define SK_PNMI_VCT_IMPEDANCE_MISMATCH 4 - -#define OID_SKGE_TRAP_SEN_WAR_LOW 500 -#define OID_SKGE_TRAP_SEN_WAR_UPP 501 -#define OID_SKGE_TRAP_SEN_ERR_LOW 502 -#define OID_SKGE_TRAP_SEN_ERR_UPP 503 -#define OID_SKGE_TRAP_RLMT_CHANGE_THRES 520 -#define OID_SKGE_TRAP_RLMT_CHANGE_PORT 521 -#define OID_SKGE_TRAP_RLMT_PORT_DOWN 522 -#define OID_SKGE_TRAP_RLMT_PORT_UP 523 -#define OID_SKGE_TRAP_RLMT_SEGMENTATION 524 - -#ifdef SK_DIAG_SUPPORT -/* Defines for driver DIAG mode. */ -#define SK_DIAG_ATTACHED 2 -#define SK_DIAG_RUNNING 1 -#define SK_DIAG_IDLE 0 -#endif /* SK_DIAG_SUPPORT */ - -/* - * Generic PNMI IOCTL subcommand definitions. - */ -#define SK_GET_SINGLE_VAR 1 -#define SK_SET_SINGLE_VAR 2 -#define SK_PRESET_SINGLE_VAR 3 -#define SK_GET_FULL_MIB 4 -#define SK_SET_FULL_MIB 5 -#define SK_PRESET_FULL_MIB 6 - - -/* - * Define error numbers and messages for syslog - */ -#define SK_PNMI_ERR001 (SK_ERRBASE_PNMI + 1) -#define SK_PNMI_ERR001MSG "SkPnmiGetStruct: Unknown OID" -#define SK_PNMI_ERR002 (SK_ERRBASE_PNMI + 2) -#define SK_PNMI_ERR002MSG "SkPnmiGetStruct: Cannot read VPD keys" -#define SK_PNMI_ERR003 (SK_ERRBASE_PNMI + 3) -#define SK_PNMI_ERR003MSG "OidStruct: Called with wrong OID" -#define SK_PNMI_ERR004 (SK_ERRBASE_PNMI + 4) -#define SK_PNMI_ERR004MSG "OidStruct: Called with wrong action" -#define SK_PNMI_ERR005 (SK_ERRBASE_PNMI + 5) -#define SK_PNMI_ERR005MSG "Perform: Cannot reset driver" -#define SK_PNMI_ERR006 (SK_ERRBASE_PNMI + 6) -#define SK_PNMI_ERR006MSG "Perform: Unknown OID action command" -#define SK_PNMI_ERR007 (SK_ERRBASE_PNMI + 7) -#define SK_PNMI_ERR007MSG "General: Driver description not initialized" -#define SK_PNMI_ERR008 (SK_ERRBASE_PNMI + 8) -#define SK_PNMI_ERR008MSG "Addr: Tried to get unknown OID" -#define SK_PNMI_ERR009 (SK_ERRBASE_PNMI + 9) -#define SK_PNMI_ERR009MSG "Addr: Unknown OID" -#define SK_PNMI_ERR010 (SK_ERRBASE_PNMI + 10) -#define SK_PNMI_ERR010MSG "CsumStat: Unknown OID" -#define SK_PNMI_ERR011 (SK_ERRBASE_PNMI + 11) -#define SK_PNMI_ERR011MSG "SensorStat: Sensor descr string too long" -#define SK_PNMI_ERR012 (SK_ERRBASE_PNMI + 12) -#define SK_PNMI_ERR012MSG "SensorStat: Unknown OID" -#define SK_PNMI_ERR013 (SK_ERRBASE_PNMI + 13) -#define SK_PNMI_ERR013MSG "" -#define SK_PNMI_ERR014 (SK_ERRBASE_PNMI + 14) -#define SK_PNMI_ERR014MSG "Vpd: Cannot read VPD keys" -#define SK_PNMI_ERR015 (SK_ERRBASE_PNMI + 15) -#define SK_PNMI_ERR015MSG "Vpd: Internal array for VPD keys to small" -#define SK_PNMI_ERR016 (SK_ERRBASE_PNMI + 16) -#define SK_PNMI_ERR016MSG "Vpd: Key string too long" -#define SK_PNMI_ERR017 (SK_ERRBASE_PNMI + 17) -#define SK_PNMI_ERR017MSG "Vpd: Invalid VPD status pointer" -#define SK_PNMI_ERR018 (SK_ERRBASE_PNMI + 18) -#define SK_PNMI_ERR018MSG "Vpd: VPD data not valid" -#define SK_PNMI_ERR019 (SK_ERRBASE_PNMI + 19) -#define SK_PNMI_ERR019MSG "Vpd: VPD entries list string too long" -#define SK_PNMI_ERR021 (SK_ERRBASE_PNMI + 21) -#define SK_PNMI_ERR021MSG "Vpd: VPD data string too long" -#define SK_PNMI_ERR022 (SK_ERRBASE_PNMI + 22) -#define SK_PNMI_ERR022MSG "Vpd: VPD data string too long should be errored before" -#define SK_PNMI_ERR023 (SK_ERRBASE_PNMI + 23) -#define SK_PNMI_ERR023MSG "Vpd: Unknown OID in get action" -#define SK_PNMI_ERR024 (SK_ERRBASE_PNMI + 24) -#define SK_PNMI_ERR024MSG "Vpd: Unknown OID in preset/set action" -#define SK_PNMI_ERR025 (SK_ERRBASE_PNMI + 25) -#define SK_PNMI_ERR025MSG "Vpd: Cannot write VPD after modify entry" -#define SK_PNMI_ERR026 (SK_ERRBASE_PNMI + 26) -#define SK_PNMI_ERR026MSG "Vpd: Cannot update VPD" -#define SK_PNMI_ERR027 (SK_ERRBASE_PNMI + 27) -#define SK_PNMI_ERR027MSG "Vpd: Cannot delete VPD entry" -#define SK_PNMI_ERR028 (SK_ERRBASE_PNMI + 28) -#define SK_PNMI_ERR028MSG "Vpd: Cannot update VPD after delete entry" -#define SK_PNMI_ERR029 (SK_ERRBASE_PNMI + 29) -#define SK_PNMI_ERR029MSG "General: Driver description string too long" -#define SK_PNMI_ERR030 (SK_ERRBASE_PNMI + 30) -#define SK_PNMI_ERR030MSG "General: Driver version not initialized" -#define SK_PNMI_ERR031 (SK_ERRBASE_PNMI + 31) -#define SK_PNMI_ERR031MSG "General: Driver version string too long" -#define SK_PNMI_ERR032 (SK_ERRBASE_PNMI + 32) -#define SK_PNMI_ERR032MSG "General: Cannot read VPD Name for HW descr" -#define SK_PNMI_ERR033 (SK_ERRBASE_PNMI + 33) -#define SK_PNMI_ERR033MSG "General: HW description string too long" -#define SK_PNMI_ERR034 (SK_ERRBASE_PNMI + 34) -#define SK_PNMI_ERR034MSG "General: Unknown OID" -#define SK_PNMI_ERR035 (SK_ERRBASE_PNMI + 35) -#define SK_PNMI_ERR035MSG "Rlmt: Unknown OID" -#define SK_PNMI_ERR036 (SK_ERRBASE_PNMI + 36) -#define SK_PNMI_ERR036MSG "" -#define SK_PNMI_ERR037 (SK_ERRBASE_PNMI + 37) -#define SK_PNMI_ERR037MSG "Rlmt: SK_RLMT_MODE_CHANGE event return not 0" -#define SK_PNMI_ERR038 (SK_ERRBASE_PNMI + 38) -#define SK_PNMI_ERR038MSG "Rlmt: SK_RLMT_PREFPORT_CHANGE event return not 0" -#define SK_PNMI_ERR039 (SK_ERRBASE_PNMI + 39) -#define SK_PNMI_ERR039MSG "RlmtStat: Unknown OID" -#define SK_PNMI_ERR040 (SK_ERRBASE_PNMI + 40) -#define SK_PNMI_ERR040MSG "PowerManagement: Unknown OID" -#define SK_PNMI_ERR041 (SK_ERRBASE_PNMI + 41) -#define SK_PNMI_ERR041MSG "MacPrivateConf: Unknown OID" -#define SK_PNMI_ERR042 (SK_ERRBASE_PNMI + 42) -#define SK_PNMI_ERR042MSG "MacPrivateConf: SK_HWEV_SET_ROLE returned not 0" -#define SK_PNMI_ERR043 (SK_ERRBASE_PNMI + 43) -#define SK_PNMI_ERR043MSG "MacPrivateConf: SK_HWEV_SET_LMODE returned not 0" -#define SK_PNMI_ERR044 (SK_ERRBASE_PNMI + 44) -#define SK_PNMI_ERR044MSG "MacPrivateConf: SK_HWEV_SET_FLOWMODE returned not 0" -#define SK_PNMI_ERR045 (SK_ERRBASE_PNMI + 45) -#define SK_PNMI_ERR045MSG "MacPrivateConf: SK_HWEV_SET_SPEED returned not 0" -#define SK_PNMI_ERR046 (SK_ERRBASE_PNMI + 46) -#define SK_PNMI_ERR046MSG "Monitor: Unknown OID" -#define SK_PNMI_ERR047 (SK_ERRBASE_PNMI + 47) -#define SK_PNMI_ERR047MSG "SirqUpdate: Event function returns not 0" -#define SK_PNMI_ERR048 (SK_ERRBASE_PNMI + 48) -#define SK_PNMI_ERR048MSG "RlmtUpdate: Event function returns not 0" -#define SK_PNMI_ERR049 (SK_ERRBASE_PNMI + 49) -#define SK_PNMI_ERR049MSG "SkPnmiInit: Invalid size of 'CounterOffset' struct!!" -#define SK_PNMI_ERR050 (SK_ERRBASE_PNMI + 50) -#define SK_PNMI_ERR050MSG "SkPnmiInit: Invalid size of 'StatAddr' table!!" -#define SK_PNMI_ERR051 (SK_ERRBASE_PNMI + 51) -#define SK_PNMI_ERR051MSG "SkPnmiEvent: Port switch suspicious" -#define SK_PNMI_ERR052 (SK_ERRBASE_PNMI + 52) -#define SK_PNMI_ERR052MSG "" -#define SK_PNMI_ERR053 (SK_ERRBASE_PNMI + 53) -#define SK_PNMI_ERR053MSG "General: Driver release date not initialized" -#define SK_PNMI_ERR054 (SK_ERRBASE_PNMI + 54) -#define SK_PNMI_ERR054MSG "General: Driver release date string too long" -#define SK_PNMI_ERR055 (SK_ERRBASE_PNMI + 55) -#define SK_PNMI_ERR055MSG "General: Driver file name not initialized" -#define SK_PNMI_ERR056 (SK_ERRBASE_PNMI + 56) -#define SK_PNMI_ERR056MSG "General: Driver file name string too long" - -/* - * Management counter macros called by the driver - */ -#define SK_PNMI_SET_DRIVER_DESCR(pAC,v) ((pAC)->Pnmi.pDriverDescription = \ - (char *)(v)) - -#define SK_PNMI_SET_DRIVER_VER(pAC,v) ((pAC)->Pnmi.pDriverVersion = \ - (char *)(v)) - -#define SK_PNMI_SET_DRIVER_RELDATE(pAC,v) ((pAC)->Pnmi.pDriverReleaseDate = \ - (char *)(v)) - -#define SK_PNMI_SET_DRIVER_FILENAME(pAC,v) ((pAC)->Pnmi.pDriverFileName = \ - (char *)(v)) - -#define SK_PNMI_CNT_TX_QUEUE_LEN(pAC,v,p) \ - { \ - (pAC)->Pnmi.Port[p].TxSwQueueLen = (SK_U64)(v); \ - if ((pAC)->Pnmi.Port[p].TxSwQueueLen > (pAC)->Pnmi.Port[p].TxSwQueueMax) { \ - (pAC)->Pnmi.Port[p].TxSwQueueMax = (pAC)->Pnmi.Port[p].TxSwQueueLen; \ - } \ - } -#define SK_PNMI_CNT_TX_RETRY(pAC,p) (((pAC)->Pnmi.Port[p].TxRetryCts)++) -#define SK_PNMI_CNT_RX_INTR(pAC,p) (((pAC)->Pnmi.Port[p].RxIntrCts)++) -#define SK_PNMI_CNT_TX_INTR(pAC,p) (((pAC)->Pnmi.Port[p].TxIntrCts)++) -#define SK_PNMI_CNT_NO_RX_BUF(pAC,p) (((pAC)->Pnmi.Port[p].RxNoBufCts)++) -#define SK_PNMI_CNT_NO_TX_BUF(pAC,p) (((pAC)->Pnmi.Port[p].TxNoBufCts)++) -#define SK_PNMI_CNT_USED_TX_DESCR(pAC,v,p) \ - ((pAC)->Pnmi.Port[p].TxUsedDescrNo=(SK_U64)(v)); -#define SK_PNMI_CNT_RX_OCTETS_DELIVERED(pAC,v,p) \ - { \ - ((pAC)->Pnmi.Port[p].RxDeliveredCts)++; \ - (pAC)->Pnmi.Port[p].RxOctetsDeliveredCts += (SK_U64)(v); \ - } -#define SK_PNMI_CNT_ERR_RECOVERY(pAC,p) (((pAC)->Pnmi.Port[p].ErrRecoveryCts)++); - -#define SK_PNMI_CNT_SYNC_OCTETS(pAC,p,v) \ - { \ - if ((p) < SK_MAX_MACS) { \ - ((pAC)->Pnmi.Port[p].StatSyncCts)++; \ - (pAC)->Pnmi.Port[p].StatSyncOctetsCts += (SK_U64)(v); \ - } \ - } - -#define SK_PNMI_CNT_RX_LONGFRAMES(pAC,p) \ - { \ - if ((p) < SK_MAX_MACS) { \ - ((pAC)->Pnmi.Port[p].StatRxLongFrameCts++); \ - } \ - } - -#define SK_PNMI_CNT_RX_FRAMETOOLONG(pAC,p) \ - { \ - if ((p) < SK_MAX_MACS) { \ - ((pAC)->Pnmi.Port[p].StatRxFrameTooLongCts++); \ - } \ - } - -#define SK_PNMI_CNT_RX_PMACC_ERR(pAC,p) \ - { \ - if ((p) < SK_MAX_MACS) { \ - ((pAC)->Pnmi.Port[p].StatRxPMaccErr++); \ - } \ - } - -/* - * Conversion Macros - */ -#define SK_PNMI_PORT_INST2LOG(i) ((unsigned int)(i) - 1) -#define SK_PNMI_PORT_LOG2INST(l) ((unsigned int)(l) + 1) -#define SK_PNMI_PORT_PHYS2LOG(p) ((unsigned int)(p) + 1) -#define SK_PNMI_PORT_LOG2PHYS(pAC,l) ((unsigned int)(l) - 1) -#define SK_PNMI_PORT_PHYS2INST(pAC,p) \ - (pAC->Pnmi.DualNetActiveFlag ? 2 : ((unsigned int)(p) + 2)) -#define SK_PNMI_PORT_INST2PHYS(pAC,i) ((unsigned int)(i) - 2) - -/* - * Structure definition for SkPnmiGetStruct and SkPnmiSetStruct - */ -#define SK_PNMI_VPD_KEY_SIZE 5 -#define SK_PNMI_VPD_BUFSIZE (VPD_SIZE) -#define SK_PNMI_VPD_ENTRIES (VPD_SIZE / 4) -#define SK_PNMI_VPD_DATALEN 128 /* Number of data bytes */ - -#define SK_PNMI_MULTICAST_LISTLEN 64 -#define SK_PNMI_SENSOR_ENTRIES (SK_MAX_SENSORS) -#define SK_PNMI_CHECKSUM_ENTRIES 3 -#define SK_PNMI_MAC_ENTRIES (SK_MAX_MACS + 1) -#define SK_PNMI_MONITOR_ENTRIES 20 -#define SK_PNMI_TRAP_ENTRIES 10 -#define SK_PNMI_TRAPLEN 128 -#define SK_PNMI_STRINGLEN1 80 -#define SK_PNMI_STRINGLEN2 25 -#define SK_PNMI_TRAP_QUEUE_LEN 512 - -typedef struct s_PnmiVpd { - char VpdKey[SK_PNMI_VPD_KEY_SIZE]; - char VpdValue[SK_PNMI_VPD_DATALEN]; - SK_U8 VpdAccess; - SK_U8 VpdAction; -} SK_PNMI_VPD; - -typedef struct s_PnmiSensor { - SK_U8 SensorIndex; - char SensorDescr[SK_PNMI_STRINGLEN2]; - SK_U8 SensorType; - SK_U32 SensorValue; - SK_U32 SensorWarningThresholdLow; - SK_U32 SensorWarningThresholdHigh; - SK_U32 SensorErrorThresholdLow; - SK_U32 SensorErrorThresholdHigh; - SK_U8 SensorStatus; - SK_U64 SensorWarningCts; - SK_U64 SensorErrorCts; - SK_U64 SensorWarningTimestamp; - SK_U64 SensorErrorTimestamp; -} SK_PNMI_SENSOR; - -typedef struct s_PnmiChecksum { - SK_U64 ChecksumRxOkCts; - SK_U64 ChecksumRxUnableCts; - SK_U64 ChecksumRxErrCts; - SK_U64 ChecksumTxOkCts; - SK_U64 ChecksumTxUnableCts; -} SK_PNMI_CHECKSUM; - -typedef struct s_PnmiStat { - SK_U64 StatTxOkCts; - SK_U64 StatTxOctetsOkCts; - SK_U64 StatTxBroadcastOkCts; - SK_U64 StatTxMulticastOkCts; - SK_U64 StatTxUnicastOkCts; - SK_U64 StatTxLongFramesCts; - SK_U64 StatTxBurstCts; - SK_U64 StatTxPauseMacCtrlCts; - SK_U64 StatTxMacCtrlCts; - SK_U64 StatTxSingleCollisionCts; - SK_U64 StatTxMultipleCollisionCts; - SK_U64 StatTxExcessiveCollisionCts; - SK_U64 StatTxLateCollisionCts; - SK_U64 StatTxDeferralCts; - SK_U64 StatTxExcessiveDeferralCts; - SK_U64 StatTxFifoUnderrunCts; - SK_U64 StatTxCarrierCts; - SK_U64 Dummy1; /* StatTxUtilization */ - SK_U64 StatTx64Cts; - SK_U64 StatTx127Cts; - SK_U64 StatTx255Cts; - SK_U64 StatTx511Cts; - SK_U64 StatTx1023Cts; - SK_U64 StatTxMaxCts; - SK_U64 StatTxSyncCts; - SK_U64 StatTxSyncOctetsCts; - SK_U64 StatRxOkCts; - SK_U64 StatRxOctetsOkCts; - SK_U64 StatRxBroadcastOkCts; - SK_U64 StatRxMulticastOkCts; - SK_U64 StatRxUnicastOkCts; - SK_U64 StatRxLongFramesCts; - SK_U64 StatRxPauseMacCtrlCts; - SK_U64 StatRxMacCtrlCts; - SK_U64 StatRxPauseMacCtrlErrorCts; - SK_U64 StatRxMacCtrlUnknownCts; - SK_U64 StatRxBurstCts; - SK_U64 StatRxMissedCts; - SK_U64 StatRxFramingCts; - SK_U64 StatRxFifoOverflowCts; - SK_U64 StatRxJabberCts; - SK_U64 StatRxCarrierCts; - SK_U64 StatRxIRLengthCts; - SK_U64 StatRxSymbolCts; - SK_U64 StatRxShortsCts; - SK_U64 StatRxRuntCts; - SK_U64 StatRxCextCts; - SK_U64 StatRxTooLongCts; - SK_U64 StatRxFcsCts; - SK_U64 Dummy2; /* StatRxUtilization */ - SK_U64 StatRx64Cts; - SK_U64 StatRx127Cts; - SK_U64 StatRx255Cts; - SK_U64 StatRx511Cts; - SK_U64 StatRx1023Cts; - SK_U64 StatRxMaxCts; -} SK_PNMI_STAT; - -typedef struct s_PnmiConf { - char ConfMacCurrentAddr[6]; - char ConfMacFactoryAddr[6]; - SK_U8 ConfPMD; - SK_U8 ConfConnector; - SK_U32 ConfPhyType; - SK_U32 ConfPhyMode; - SK_U8 ConfLinkCapability; - SK_U8 ConfLinkMode; - SK_U8 ConfLinkModeStatus; - SK_U8 ConfLinkStatus; - SK_U8 ConfFlowCtrlCapability; - SK_U8 ConfFlowCtrlMode; - SK_U8 ConfFlowCtrlStatus; - SK_U8 ConfPhyOperationCapability; - SK_U8 ConfPhyOperationMode; - SK_U8 ConfPhyOperationStatus; - SK_U8 ConfSpeedCapability; - SK_U8 ConfSpeedMode; - SK_U8 ConfSpeedStatus; -} SK_PNMI_CONF; - -typedef struct s_PnmiRlmt { - SK_U32 RlmtIndex; - SK_U32 RlmtStatus; - SK_U64 RlmtTxHelloCts; - SK_U64 RlmtRxHelloCts; - SK_U64 RlmtTxSpHelloReqCts; - SK_U64 RlmtRxSpHelloCts; -} SK_PNMI_RLMT; - -typedef struct s_PnmiRlmtMonitor { - SK_U32 RlmtMonitorIndex; - char RlmtMonitorAddr[6]; - SK_U64 RlmtMonitorErrorCts; - SK_U64 RlmtMonitorTimestamp; - SK_U8 RlmtMonitorAdmin; -} SK_PNMI_RLMT_MONITOR; - -typedef struct s_PnmiRequestStatus { - SK_U32 ErrorStatus; - SK_U32 ErrorOffset; -} SK_PNMI_REQUEST_STATUS; - -typedef struct s_PnmiStrucData { - SK_U32 MgmtDBVersion; - SK_PNMI_REQUEST_STATUS ReturnStatus; - SK_U32 VpdFreeBytes; - char VpdEntriesList[SK_PNMI_VPD_ENTRIES * SK_PNMI_VPD_KEY_SIZE]; - SK_U32 VpdEntriesNumber; - SK_PNMI_VPD Vpd[SK_PNMI_VPD_ENTRIES]; - SK_U32 PortNumber; - SK_U32 DeviceType; - char DriverDescr[SK_PNMI_STRINGLEN1]; - char DriverVersion[SK_PNMI_STRINGLEN2]; - char DriverReleaseDate[SK_PNMI_STRINGLEN1]; - char DriverFileName[SK_PNMI_STRINGLEN1]; - char HwDescr[SK_PNMI_STRINGLEN1]; - char HwVersion[SK_PNMI_STRINGLEN2]; - SK_U16 Chipset; - SK_U32 ChipId; - SK_U8 VauxAvail; - SK_U32 RamSize; - SK_U32 MtuSize; - SK_U32 Action; - SK_U32 TestResult; - SK_U8 BusType; - SK_U8 BusSpeed; - SK_U8 BusWidth; - SK_U8 SensorNumber; - SK_PNMI_SENSOR Sensor[SK_PNMI_SENSOR_ENTRIES]; - SK_U8 ChecksumNumber; - SK_PNMI_CHECKSUM Checksum[SK_PNMI_CHECKSUM_ENTRIES]; - SK_PNMI_STAT Stat[SK_PNMI_MAC_ENTRIES]; - SK_PNMI_CONF Conf[SK_PNMI_MAC_ENTRIES]; - SK_U8 RlmtMode; - SK_U32 RlmtPortNumber; - SK_U8 RlmtPortActive; - SK_U8 RlmtPortPreferred; - SK_U64 RlmtChangeCts; - SK_U64 RlmtChangeTime; - SK_U64 RlmtChangeEstimate; - SK_U64 RlmtChangeThreshold; - SK_PNMI_RLMT Rlmt[SK_MAX_MACS]; - SK_U32 RlmtMonitorNumber; - SK_PNMI_RLMT_MONITOR RlmtMonitor[SK_PNMI_MONITOR_ENTRIES]; - SK_U32 TrapNumber; - SK_U8 Trap[SK_PNMI_TRAP_QUEUE_LEN]; - SK_U64 TxSwQueueLen; - SK_U64 TxSwQueueMax; - SK_U64 TxRetryCts; - SK_U64 RxIntrCts; - SK_U64 TxIntrCts; - SK_U64 RxNoBufCts; - SK_U64 TxNoBufCts; - SK_U64 TxUsedDescrNo; - SK_U64 RxDeliveredCts; - SK_U64 RxOctetsDeliveredCts; - SK_U64 RxHwErrorsCts; - SK_U64 TxHwErrorsCts; - SK_U64 InErrorsCts; - SK_U64 OutErrorsCts; - SK_U64 ErrRecoveryCts; - SK_U64 SysUpTime; -} SK_PNMI_STRUCT_DATA; - -#define SK_PNMI_STRUCT_SIZE (sizeof(SK_PNMI_STRUCT_DATA)) -#define SK_PNMI_MIN_STRUCT_SIZE ((unsigned int)(SK_UPTR)\ - &(((SK_PNMI_STRUCT_DATA *)0)->VpdFreeBytes)) - /* - * ReturnStatus field - * must be located - * before VpdFreeBytes - */ - -/* - * Various definitions - */ -#define SK_PNMI_MAX_PROTOS 3 - -#define SK_PNMI_CNT_NO 66 /* Must have the value of the enum - * SK_PNMI_MAX_IDX. Define SK_PNMI_CHECK - * for check while init phase 1 - */ - -/* - * Estimate data structure - */ -typedef struct s_PnmiEstimate { - unsigned int EstValueIndex; - SK_U64 EstValue[7]; - SK_U64 Estimate; - SK_TIMER EstTimer; -} SK_PNMI_ESTIMATE; - - -/* - * VCT timer data structure - */ -typedef struct s_VctTimer { - SK_TIMER VctTimer; -} SK_PNMI_VCT_TIMER; - - -/* - * PNMI specific adapter context structure - */ -typedef struct s_PnmiPort { - SK_U64 StatSyncCts; - SK_U64 StatSyncOctetsCts; - SK_U64 StatRxLongFrameCts; - SK_U64 StatRxFrameTooLongCts; - SK_U64 StatRxPMaccErr; - SK_U64 TxSwQueueLen; - SK_U64 TxSwQueueMax; - SK_U64 TxRetryCts; - SK_U64 RxIntrCts; - SK_U64 TxIntrCts; - SK_U64 RxNoBufCts; - SK_U64 TxNoBufCts; - SK_U64 TxUsedDescrNo; - SK_U64 RxDeliveredCts; - SK_U64 RxOctetsDeliveredCts; - SK_U64 RxHwErrorsCts; - SK_U64 TxHwErrorsCts; - SK_U64 InErrorsCts; - SK_U64 OutErrorsCts; - SK_U64 ErrRecoveryCts; - SK_U64 RxShortZeroMark; - SK_U64 CounterOffset[SK_PNMI_CNT_NO]; - SK_U32 CounterHigh[SK_PNMI_CNT_NO]; - SK_BOOL ActiveFlag; - SK_U8 Align[3]; -} SK_PNMI_PORT; - - -typedef struct s_PnmiData { - SK_PNMI_PORT Port [SK_MAX_MACS]; - SK_PNMI_PORT BufPort [SK_MAX_MACS]; /* 2002-09-13 pweber */ - SK_U64 VirtualCounterOffset[SK_PNMI_CNT_NO]; - SK_U32 TestResult; - char HwVersion[10]; - SK_U16 Align01; - - char *pDriverDescription; - char *pDriverVersion; - char *pDriverReleaseDate; - char *pDriverFileName; - - int MacUpdatedFlag; - int RlmtUpdatedFlag; - int SirqUpdatedFlag; - - SK_U64 RlmtChangeCts; - SK_U64 RlmtChangeTime; - SK_PNMI_ESTIMATE RlmtChangeEstimate; - SK_U64 RlmtChangeThreshold; - - SK_U64 StartUpTime; - SK_U32 DeviceType; - char PciBusSpeed; - char PciBusWidth; - char Chipset; - char PMD; - char Connector; - SK_BOOL DualNetActiveFlag; - SK_U16 Align02; - - char TrapBuf[SK_PNMI_TRAP_QUEUE_LEN]; - unsigned int TrapBufFree; - unsigned int TrapQueueBeg; - unsigned int TrapQueueEnd; - unsigned int TrapBufPad; - unsigned int TrapUnique; - SK_U8 VctStatus[SK_MAX_MACS]; - SK_PNMI_VCT VctBackup[SK_MAX_MACS]; - SK_PNMI_VCT_TIMER VctTimeout[SK_MAX_MACS]; -#ifdef SK_DIAG_SUPPORT - SK_U32 DiagAttached; -#endif /* SK_DIAG_SUPPORT */ -} SK_PNMI; - - -/* - * Function prototypes - */ -extern int SkPnmiInit(SK_AC *pAC, SK_IOC IoC, int Level); -extern int SkPnmiSetVar(SK_AC *pAC, SK_IOC IoC, SK_U32 Id, void* pBuf, - unsigned int *pLen, SK_U32 Instance, SK_U32 NetIndex); -extern int SkPnmiGetStruct(SK_AC *pAC, SK_IOC IoC, void* pBuf, - unsigned int *pLen, SK_U32 NetIndex); -extern int SkPnmiPreSetStruct(SK_AC *pAC, SK_IOC IoC, void* pBuf, - unsigned int *pLen, SK_U32 NetIndex); -extern int SkPnmiSetStruct(SK_AC *pAC, SK_IOC IoC, void* pBuf, - unsigned int *pLen, SK_U32 NetIndex); -extern int SkPnmiEvent(SK_AC *pAC, SK_IOC IoC, SK_U32 Event, - SK_EVPARA Param); -extern int SkPnmiGenIoctl(SK_AC *pAC, SK_IOC IoC, void * pBuf, - unsigned int * pLen, SK_U32 NetIndex); - -#endif diff --git a/drivers/net/sk98lin/h/skgesirq.h b/drivers/net/sk98lin/h/skgesirq.h deleted file mode 100644 index 3eec6274e413..000000000000 --- a/drivers/net/sk98lin/h/skgesirq.h +++ /dev/null @@ -1,110 +0,0 @@ -/****************************************************************************** - * - * Name: skgesirq.h - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.30 $ - * Date: $Date: 2003/07/04 12:34:13 $ - * Purpose: SK specific Gigabit Ethernet special IRQ functions - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef _INC_SKGESIRQ_H_ -#define _INC_SKGESIRQ_H_ - -/* Define return codes of SkGePortCheckUp and CheckShort */ -#define SK_HW_PS_NONE 0 /* No action needed */ -#define SK_HW_PS_RESTART 1 /* Restart needed */ -#define SK_HW_PS_LINK 2 /* Link Up actions needed */ - -/* - * Define the Event the special IRQ/INI module can handle - */ -#define SK_HWEV_WATIM 1 /* Timeout for WA Errata #2 XMAC */ -#define SK_HWEV_PORT_START 2 /* Port Start Event by RLMT */ -#define SK_HWEV_PORT_STOP 3 /* Port Stop Event by RLMT */ -#define SK_HWEV_CLEAR_STAT 4 /* Clear Statistics by PNMI */ -#define SK_HWEV_UPDATE_STAT 5 /* Update Statistics by PNMI */ -#define SK_HWEV_SET_LMODE 6 /* Set Link Mode by PNMI */ -#define SK_HWEV_SET_FLOWMODE 7 /* Set Flow Control Mode by PNMI */ -#define SK_HWEV_SET_ROLE 8 /* Set Master/Slave (Role) by PNMI */ -#define SK_HWEV_SET_SPEED 9 /* Set Link Speed by PNMI */ -#define SK_HWEV_HALFDUP_CHK 10 /* Half Duplex Hangup Workaround */ - -#define SK_WA_ACT_TIME (5000000UL) /* 5 sec */ -#define SK_WA_INA_TIME (100000UL) /* 100 msec */ - -#define SK_HALFDUP_CHK_TIME (10000UL) /* 10 msec */ - -/* - * Define the error numbers and messages - */ -#define SKERR_SIRQ_E001 (SK_ERRBASE_SIRQ+0) -#define SKERR_SIRQ_E001MSG "Unknown event" -#define SKERR_SIRQ_E002 (SKERR_SIRQ_E001+1) -#define SKERR_SIRQ_E002MSG "Packet timeout RX1" -#define SKERR_SIRQ_E003 (SKERR_SIRQ_E002+1) -#define SKERR_SIRQ_E003MSG "Packet timeout RX2" -#define SKERR_SIRQ_E004 (SKERR_SIRQ_E003+1) -#define SKERR_SIRQ_E004MSG "MAC 1 not correctly initialized" -#define SKERR_SIRQ_E005 (SKERR_SIRQ_E004+1) -#define SKERR_SIRQ_E005MSG "MAC 2 not correctly initialized" -#define SKERR_SIRQ_E006 (SKERR_SIRQ_E005+1) -#define SKERR_SIRQ_E006MSG "CHECK failure R1" -#define SKERR_SIRQ_E007 (SKERR_SIRQ_E006+1) -#define SKERR_SIRQ_E007MSG "CHECK failure R2" -#define SKERR_SIRQ_E008 (SKERR_SIRQ_E007+1) -#define SKERR_SIRQ_E008MSG "CHECK failure XS1" -#define SKERR_SIRQ_E009 (SKERR_SIRQ_E008+1) -#define SKERR_SIRQ_E009MSG "CHECK failure XA1" -#define SKERR_SIRQ_E010 (SKERR_SIRQ_E009+1) -#define SKERR_SIRQ_E010MSG "CHECK failure XS2" -#define SKERR_SIRQ_E011 (SKERR_SIRQ_E010+1) -#define SKERR_SIRQ_E011MSG "CHECK failure XA2" -#define SKERR_SIRQ_E012 (SKERR_SIRQ_E011+1) -#define SKERR_SIRQ_E012MSG "unexpected IRQ Master error" -#define SKERR_SIRQ_E013 (SKERR_SIRQ_E012+1) -#define SKERR_SIRQ_E013MSG "unexpected IRQ Status error" -#define SKERR_SIRQ_E014 (SKERR_SIRQ_E013+1) -#define SKERR_SIRQ_E014MSG "Parity error on RAM (read)" -#define SKERR_SIRQ_E015 (SKERR_SIRQ_E014+1) -#define SKERR_SIRQ_E015MSG "Parity error on RAM (write)" -#define SKERR_SIRQ_E016 (SKERR_SIRQ_E015+1) -#define SKERR_SIRQ_E016MSG "Parity error MAC 1" -#define SKERR_SIRQ_E017 (SKERR_SIRQ_E016+1) -#define SKERR_SIRQ_E017MSG "Parity error MAC 2" -#define SKERR_SIRQ_E018 (SKERR_SIRQ_E017+1) -#define SKERR_SIRQ_E018MSG "Parity error RX 1" -#define SKERR_SIRQ_E019 (SKERR_SIRQ_E018+1) -#define SKERR_SIRQ_E019MSG "Parity error RX 2" -#define SKERR_SIRQ_E020 (SKERR_SIRQ_E019+1) -#define SKERR_SIRQ_E020MSG "MAC transmit FIFO underrun" -#define SKERR_SIRQ_E021 (SKERR_SIRQ_E020+1) -#define SKERR_SIRQ_E021MSG "Spurious TWSI interrupt" -#define SKERR_SIRQ_E022 (SKERR_SIRQ_E021+1) -#define SKERR_SIRQ_E022MSG "Cable pair swap error" -#define SKERR_SIRQ_E023 (SKERR_SIRQ_E022+1) -#define SKERR_SIRQ_E023MSG "Auto-negotiation error" -#define SKERR_SIRQ_E024 (SKERR_SIRQ_E023+1) -#define SKERR_SIRQ_E024MSG "FIFO overflow error" -#define SKERR_SIRQ_E025 (SKERR_SIRQ_E024+1) -#define SKERR_SIRQ_E025MSG "2 Pair Downshift detected" - -extern void SkGeSirqIsr(SK_AC *pAC, SK_IOC IoC, SK_U32 Istatus); -extern int SkGeSirqEvent(SK_AC *pAC, SK_IOC IoC, SK_U32 Event, SK_EVPARA Para); -extern void SkHWLinkDown(SK_AC *pAC, SK_IOC IoC, int Port); - -#endif /* _INC_SKGESIRQ_H_ */ diff --git a/drivers/net/sk98lin/h/ski2c.h b/drivers/net/sk98lin/h/ski2c.h deleted file mode 100644 index 6a63f4a15de6..000000000000 --- a/drivers/net/sk98lin/h/ski2c.h +++ /dev/null @@ -1,174 +0,0 @@ -/****************************************************************************** - * - * Name: ski2c.h - * Project: Gigabit Ethernet Adapters, TWSI-Module - * Version: $Revision: 1.35 $ - * Date: $Date: 2003/10/20 09:06:30 $ - * Purpose: Defines to access Voltage and Temperature Sensor - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * SKI2C.H contains all I2C specific defines - */ - -#ifndef _SKI2C_H_ -#define _SKI2C_H_ - -typedef struct s_Sensor SK_SENSOR; - -#include "h/skgei2c.h" - -/* - * Define the I2C events. - */ -#define SK_I2CEV_IRQ 1 /* IRQ happened Event */ -#define SK_I2CEV_TIM 2 /* Timeout event */ -#define SK_I2CEV_CLEAR 3 /* Clear MIB Values */ - -/* - * Define READ and WRITE Constants. - */ -#define I2C_READ 0 -#define I2C_WRITE 1 -#define I2C_BURST 1 -#define I2C_SINGLE 0 - -#define SKERR_I2C_E001 (SK_ERRBASE_I2C+0) -#define SKERR_I2C_E001MSG "Sensor index unknown" -#define SKERR_I2C_E002 (SKERR_I2C_E001+1) -#define SKERR_I2C_E002MSG "TWSI: transfer does not complete" -#define SKERR_I2C_E003 (SKERR_I2C_E002+1) -#define SKERR_I2C_E003MSG "LM80: NAK on device send" -#define SKERR_I2C_E004 (SKERR_I2C_E003+1) -#define SKERR_I2C_E004MSG "LM80: NAK on register send" -#define SKERR_I2C_E005 (SKERR_I2C_E004+1) -#define SKERR_I2C_E005MSG "LM80: NAK on device (2) send" -#define SKERR_I2C_E006 (SKERR_I2C_E005+1) -#define SKERR_I2C_E006MSG "Unknown event" -#define SKERR_I2C_E007 (SKERR_I2C_E006+1) -#define SKERR_I2C_E007MSG "LM80 read out of state" -#define SKERR_I2C_E008 (SKERR_I2C_E007+1) -#define SKERR_I2C_E008MSG "Unexpected sensor read completed" -#define SKERR_I2C_E009 (SKERR_I2C_E008+1) -#define SKERR_I2C_E009MSG "WARNING: temperature sensor out of range" -#define SKERR_I2C_E010 (SKERR_I2C_E009+1) -#define SKERR_I2C_E010MSG "WARNING: voltage sensor out of range" -#define SKERR_I2C_E011 (SKERR_I2C_E010+1) -#define SKERR_I2C_E011MSG "ERROR: temperature sensor out of range" -#define SKERR_I2C_E012 (SKERR_I2C_E011+1) -#define SKERR_I2C_E012MSG "ERROR: voltage sensor out of range" -#define SKERR_I2C_E013 (SKERR_I2C_E012+1) -#define SKERR_I2C_E013MSG "ERROR: couldn't init sensor" -#define SKERR_I2C_E014 (SKERR_I2C_E013+1) -#define SKERR_I2C_E014MSG "WARNING: fan sensor out of range" -#define SKERR_I2C_E015 (SKERR_I2C_E014+1) -#define SKERR_I2C_E015MSG "ERROR: fan sensor out of range" -#define SKERR_I2C_E016 (SKERR_I2C_E015+1) -#define SKERR_I2C_E016MSG "TWSI: active transfer does not complete" - -/* - * Define Timeout values - */ -#define SK_I2C_TIM_LONG 2000000L /* 2 seconds */ -#define SK_I2C_TIM_SHORT 100000L /* 100 milliseconds */ -#define SK_I2C_TIM_WATCH 1000000L /* 1 second */ - -/* - * Define trap and error log hold times - */ -#ifndef SK_SEN_ERR_TR_HOLD -#define SK_SEN_ERR_TR_HOLD (4*SK_TICKS_PER_SEC) -#endif -#ifndef SK_SEN_ERR_LOG_HOLD -#define SK_SEN_ERR_LOG_HOLD (60*SK_TICKS_PER_SEC) -#endif -#ifndef SK_SEN_WARN_TR_HOLD -#define SK_SEN_WARN_TR_HOLD (15*SK_TICKS_PER_SEC) -#endif -#ifndef SK_SEN_WARN_LOG_HOLD -#define SK_SEN_WARN_LOG_HOLD (15*60*SK_TICKS_PER_SEC) -#endif - -/* - * Defines for SenType - */ -#define SK_SEN_UNKNOWN 0 -#define SK_SEN_TEMP 1 -#define SK_SEN_VOLT 2 -#define SK_SEN_FAN 3 - -/* - * Define for the SenErrorFlag - */ -#define SK_SEN_ERR_NOT_PRESENT 0 /* Error Flag: Sensor not present */ -#define SK_SEN_ERR_OK 1 /* Error Flag: O.K. */ -#define SK_SEN_ERR_WARN 2 /* Error Flag: Warning */ -#define SK_SEN_ERR_ERR 3 /* Error Flag: Error */ -#define SK_SEN_ERR_FAULTY 4 /* Error Flag: Faulty */ - -/* - * Define the Sensor struct - */ -struct s_Sensor { - char *SenDesc; /* Description */ - int SenType; /* Voltage or Temperature */ - SK_I32 SenValue; /* Current value of the sensor */ - SK_I32 SenThreErrHigh; /* High error Threshhold of this sensor */ - SK_I32 SenThreWarnHigh; /* High warning Threshhold of this sensor */ - SK_I32 SenThreErrLow; /* Lower error Threshold of the sensor */ - SK_I32 SenThreWarnLow; /* Lower warning Threshold of the sensor */ - int SenErrFlag; /* Sensor indicated an error */ - SK_BOOL SenInit; /* Is sensor initialized ? */ - SK_U64 SenErrCts; /* Error trap counter */ - SK_U64 SenWarnCts; /* Warning trap counter */ - SK_U64 SenBegErrTS; /* Begin error timestamp */ - SK_U64 SenBegWarnTS; /* Begin warning timestamp */ - SK_U64 SenLastErrTrapTS; /* Last error trap timestamp */ - SK_U64 SenLastErrLogTS; /* Last error log timestamp */ - SK_U64 SenLastWarnTrapTS; /* Last warning trap timestamp */ - SK_U64 SenLastWarnLogTS; /* Last warning log timestamp */ - int SenState; /* Sensor State (see HW specific include) */ - int (*SenRead)(SK_AC *pAC, SK_IOC IoC, struct s_Sensor *pSen); - /* Sensors read function */ - SK_U16 SenReg; /* Register Address for this sensor */ - SK_U8 SenDev; /* Device Selection for this sensor */ -}; - -typedef struct s_I2c { - SK_SENSOR SenTable[SK_MAX_SENSORS]; /* Sensor Table */ - int CurrSens; /* Which sensor is currently queried */ - int MaxSens; /* Max. number of sensors */ - int TimerMode; /* Use the timer also to watch the state machine */ - int InitLevel; /* Initialized Level */ -#ifndef SK_DIAG - int DummyReads; /* Number of non-checked dummy reads */ - SK_TIMER SenTimer; /* Sensors timer */ -#endif /* !SK_DIAG */ -} SK_I2C; - -extern int SkI2cInit(SK_AC *pAC, SK_IOC IoC, int Level); -#ifdef SK_DIAG -extern SK_U32 SkI2cRead(SK_AC *pAC, SK_IOC IoC, int Dev, int Size, int Reg, - int Burst); -#else /* !SK_DIAG */ -extern int SkI2cEvent(SK_AC *pAC, SK_IOC IoC, SK_U32 Event, SK_EVPARA Para); -extern void SkI2cWaitIrq(SK_AC *pAC, SK_IOC IoC); -extern void SkI2cIsr(SK_AC *pAC, SK_IOC IoC); -#endif /* !SK_DIAG */ -#endif /* n_SKI2C_H */ - diff --git a/drivers/net/sk98lin/h/skqueue.h b/drivers/net/sk98lin/h/skqueue.h deleted file mode 100644 index 2ec40d4fdf60..000000000000 --- a/drivers/net/sk98lin/h/skqueue.h +++ /dev/null @@ -1,94 +0,0 @@ -/****************************************************************************** - * - * Name: skqueue.h - * Project: Gigabit Ethernet Adapters, Event Scheduler Module - * Version: $Revision: 1.16 $ - * Date: $Date: 2003/09/16 12:50:32 $ - * Purpose: Defines for the Event queue - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * SKQUEUE.H contains all defines and types for the event queue - */ - -#ifndef _SKQUEUE_H_ -#define _SKQUEUE_H_ - - -/* - * define the event classes to be served - */ -#define SKGE_DRV 1 /* Driver Event Class */ -#define SKGE_RLMT 2 /* RLMT Event Class */ -#define SKGE_I2C 3 /* I2C Event Class */ -#define SKGE_PNMI 4 /* PNMI Event Class */ -#define SKGE_CSUM 5 /* Checksum Event Class */ -#define SKGE_HWAC 6 /* Hardware Access Event Class */ - -#define SKGE_SWT 9 /* Software Timer Event Class */ -#define SKGE_LACP 10 /* LACP Aggregation Event Class */ -#define SKGE_RSF 11 /* RSF Aggregation Event Class */ -#define SKGE_MARKER 12 /* MARKER Aggregation Event Class */ -#define SKGE_FD 13 /* FD Distributor Event Class */ - -/* - * define event queue as circular buffer - */ -#define SK_MAX_EVENT 64 - -/* - * Parameter union for the Para stuff - */ -typedef union u_EvPara { - void *pParaPtr; /* Parameter Pointer */ - SK_U64 Para64; /* Parameter 64bit version */ - SK_U32 Para32[2]; /* Parameter Array of 32bit parameters */ -} SK_EVPARA; - -/* - * Event Queue - * skqueue.c - * events are class/value pairs - * class is addressee, e.g. RLMT, PNMI etc. - * value is command, e.g. line state change, ring op change etc. - */ -typedef struct s_EventElem { - SK_U32 Class; /* Event class */ - SK_U32 Event; /* Event value */ - SK_EVPARA Para; /* Event parameter */ -} SK_EVENTELEM; - -typedef struct s_Queue { - SK_EVENTELEM EvQueue[SK_MAX_EVENT]; - SK_EVENTELEM *EvPut; - SK_EVENTELEM *EvGet; -} SK_QUEUE; - -extern void SkEventInit(SK_AC *pAC, SK_IOC Ioc, int Level); -extern void SkEventQueue(SK_AC *pAC, SK_U32 Class, SK_U32 Event, - SK_EVPARA Para); -extern int SkEventDispatcher(SK_AC *pAC, SK_IOC Ioc); - - -/* Define Error Numbers and messages */ -#define SKERR_Q_E001 (SK_ERRBASE_QUEUE+0) -#define SKERR_Q_E001MSG "Event queue overflow" -#define SKERR_Q_E002 (SKERR_Q_E001+1) -#define SKERR_Q_E002MSG "Undefined event class" -#endif /* _SKQUEUE_H_ */ - diff --git a/drivers/net/sk98lin/h/skrlmt.h b/drivers/net/sk98lin/h/skrlmt.h deleted file mode 100644 index ca75dfdcf2d6..000000000000 --- a/drivers/net/sk98lin/h/skrlmt.h +++ /dev/null @@ -1,438 +0,0 @@ -/****************************************************************************** - * - * Name: skrlmt.h - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.37 $ - * Date: $Date: 2003/04/15 09:43:43 $ - * Purpose: Header file for Redundant Link ManagemenT. - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * This is the header file for Redundant Link ManagemenT. - * - * Include File Hierarchy: - * - * "skdrv1st.h" - * ... - * "sktypes.h" - * "skqueue.h" - * "skaddr.h" - * "skrlmt.h" - * ... - * "skdrv2nd.h" - * - ******************************************************************************/ - -#ifndef __INC_SKRLMT_H -#define __INC_SKRLMT_H - -#ifdef __cplusplus -extern "C" { -#endif /* cplusplus */ - -/* defines ********************************************************************/ - -#define SK_RLMT_NET_DOWN_TEMP 1 /* NET_DOWN due to last port down. */ -#define SK_RLMT_NET_DOWN_FINAL 2 /* NET_DOWN due to RLMT_STOP. */ - -/* ----- Default queue sizes - must be multiples of 8 KB ----- */ - -/* Less than 8 KB free in RX queue => pause frames. */ -#define SK_RLMT_STANDBY_QRXSIZE 128 /* Size of rx standby queue in KB. */ -#define SK_RLMT_STANDBY_QXASIZE 32 /* Size of async standby queue in KB. */ -#define SK_RLMT_STANDBY_QXSSIZE 0 /* Size of sync standby queue in KB. */ - -#define SK_RLMT_MAX_TX_BUF_SIZE 60 /* Maximum RLMT transmit size. */ - -/* ----- PORT states ----- */ - -#define SK_RLMT_PS_INIT 0 /* Port state: Init. */ -#define SK_RLMT_PS_LINK_DOWN 1 /* Port state: Link down. */ -#define SK_RLMT_PS_DOWN 2 /* Port state: Port down. */ -#define SK_RLMT_PS_GOING_UP 3 /* Port state: Going up. */ -#define SK_RLMT_PS_UP 4 /* Port state: Up. */ - -/* ----- RLMT states ----- */ - -#define SK_RLMT_RS_INIT 0 /* RLMT state: Init. */ -#define SK_RLMT_RS_NET_DOWN 1 /* RLMT state: Net down. */ -#define SK_RLMT_RS_NET_UP 2 /* RLMT state: Net up. */ - -/* ----- PORT events ----- */ - -#define SK_RLMT_LINK_UP 1001 /* Link came up. */ -#define SK_RLMT_LINK_DOWN 1002 /* Link went down. */ -#define SK_RLMT_PORT_ADDR 1003 /* Port address changed. */ - -/* ----- RLMT events ----- */ - -#define SK_RLMT_START 2001 /* Start RLMT. */ -#define SK_RLMT_STOP 2002 /* Stop RLMT. */ -#define SK_RLMT_PACKET_RECEIVED 2003 /* Packet was received for RLMT. */ -#define SK_RLMT_STATS_CLEAR 2004 /* Clear statistics. */ -#define SK_RLMT_STATS_UPDATE 2005 /* Update statistics. */ -#define SK_RLMT_PREFPORT_CHANGE 2006 /* Change preferred port. */ -#define SK_RLMT_MODE_CHANGE 2007 /* New RlmtMode. */ -#define SK_RLMT_SET_NETS 2008 /* Number of Nets (1 or 2). */ - -/* ----- RLMT mode bits ----- */ - -/* - * CAUTION: These defines are private to RLMT. - * Please use the RLMT mode defines below. - */ - -#define SK_RLMT_CHECK_LINK 1 /* Check Link. */ -#define SK_RLMT_CHECK_LOC_LINK 2 /* Check other link on same adapter. */ -#define SK_RLMT_CHECK_SEG 4 /* Check segmentation. */ - -#ifndef RLMT_CHECK_REMOTE -#define SK_RLMT_CHECK_OTHERS SK_RLMT_CHECK_LOC_LINK -#else /* RLMT_CHECK_REMOTE */ -#define SK_RLMT_CHECK_REM_LINK 8 /* Check link(s) on other adapter(s). */ -#define SK_RLMT_MAX_REMOTE_PORTS_CHECKED 3 -#define SK_RLMT_CHECK_OTHERS \ - (SK_RLMT_CHECK_LOC_LINK | SK_RLMT_CHECK_REM_LINK) -#endif /* RLMT_CHECK_REMOTE */ - -#ifndef SK_RLMT_ENABLE_TRANSPARENT -#define SK_RLMT_TRANSPARENT 0 /* RLMT transparent - inactive. */ -#else /* SK_RLMT_ENABLE_TRANSPARENT */ -#define SK_RLMT_TRANSPARENT 128 /* RLMT transparent. */ -#endif /* SK_RLMT_ENABLE_TRANSPARENT */ - -/* ----- RLMT modes ----- */ - -/* Check Link State. */ -#define SK_RLMT_MODE_CLS (SK_RLMT_CHECK_LINK) - -/* Check Local Ports: check other links on the same adapter. */ -#define SK_RLMT_MODE_CLP (SK_RLMT_CHECK_LINK | SK_RLMT_CHECK_LOC_LINK) - -/* Check Local Ports and Segmentation Status. */ -#define SK_RLMT_MODE_CLPSS \ - (SK_RLMT_CHECK_LINK | SK_RLMT_CHECK_LOC_LINK | SK_RLMT_CHECK_SEG) - -#ifdef RLMT_CHECK_REMOTE -/* Check Local and Remote Ports: check links (local or remote). */ - Name of define TBD! -#define SK_RLMT_MODE_CRP \ - (SK_RLMT_CHECK_LINK | SK_RLMT_CHECK_LOC_LINK | SK_RLMT_CHECK_REM_LINK) - -/* Check Local and Remote Ports and Segmentation Status. */ - Name of define TBD! -#define SK_RLMT_MODE_CRPSS \ - (SK_RLMT_CHECK_LINK | SK_RLMT_CHECK_LOC_LINK | \ - SK_RLMT_CHECK_REM_LINK | SK_RLMT_CHECK_SEG) -#endif /* RLMT_CHECK_REMOTE */ - -/* ----- RLMT lookahead result bits ----- */ - -#define SK_RLMT_RX_RLMT 1 /* Give packet to RLMT. */ -#define SK_RLMT_RX_PROTOCOL 2 /* Give packet to protocol. */ - -/* Macros */ - -#if 0 -SK_AC *pAC /* adapter context */ -SK_U32 PortNum /* receiving port */ -unsigned PktLen /* received packet's length */ -SK_BOOL IsBc /* Flag: packet is broadcast */ -unsigned *pOffset /* offs. of bytes to present to SK_RLMT_LOOKAHEAD */ -unsigned *pNumBytes /* #Bytes to present to SK_RLMT_LOOKAHEAD */ -#endif /* 0 */ - -#define SK_RLMT_PRE_LOOKAHEAD(pAC,PortNum,PktLen,IsBc,pOffset,pNumBytes) { \ - SK_AC *_pAC; \ - SK_U32 _PortNum; \ - _pAC = (pAC); \ - _PortNum = (SK_U32)(PortNum); \ - /* _pAC->Rlmt.Port[_PortNum].PacketsRx++; */ \ - _pAC->Rlmt.Port[_PortNum].PacketsPerTimeSlot++; \ - if (_pAC->Rlmt.RlmtOff) { \ - *(pNumBytes) = 0; \ - } \ - else {\ - if ((_pAC->Rlmt.Port[_PortNum].Net->RlmtMode & SK_RLMT_TRANSPARENT) != 0) { \ - *(pNumBytes) = 0; \ - } \ - else if (IsBc) { \ - if (_pAC->Rlmt.Port[_PortNum].Net->RlmtMode != SK_RLMT_MODE_CLS) { \ - *(pNumBytes) = 6; \ - *(pOffset) = 6; \ - } \ - else { \ - *(pNumBytes) = 0; \ - } \ - } \ - else { \ - if ((PktLen) > SK_RLMT_MAX_TX_BUF_SIZE) { \ - /* _pAC->Rlmt.Port[_PortNum].DataPacketsPerTimeSlot++; */ \ - *(pNumBytes) = 0; \ - } \ - else { \ - *(pNumBytes) = 6; \ - *(pOffset) = 0; \ - } \ - } \ - } \ -} - -#if 0 -SK_AC *pAC /* adapter context */ -SK_U32 PortNum /* receiving port */ -SK_U8 *pLaPacket, /* received packet's data (points to pOffset) */ -SK_BOOL IsBc /* Flag: packet is broadcast */ -SK_BOOL IsMc /* Flag: packet is multicast */ -unsigned *pForRlmt /* Result: bits SK_RLMT_RX_RLMT, SK_RLMT_RX_PROTOCOL */ -SK_RLMT_LOOKAHEAD() expects *pNumBytes from -packet offset *pOffset (s.a.) at *pLaPacket. - -If you use SK_RLMT_LOOKAHEAD in a path where you already know if the packet is -BC, MC, or UC, you should use constants for IsBc and IsMc, so that your compiler -can trash unneeded parts of the if construction. -#endif /* 0 */ - -#define SK_RLMT_LOOKAHEAD(pAC,PortNum,pLaPacket,IsBc,IsMc,pForRlmt) { \ - SK_AC *_pAC; \ - SK_U32 _PortNum; \ - SK_U8 *_pLaPacket; \ - _pAC = (pAC); \ - _PortNum = (SK_U32)(PortNum); \ - _pLaPacket = (SK_U8 *)(pLaPacket); \ - if (IsBc) {\ - if (!SK_ADDR_EQUAL(_pLaPacket, _pAC->Addr.Net[_pAC->Rlmt.Port[ \ - _PortNum].Net->NetNumber].CurrentMacAddress.a)) { \ - _pAC->Rlmt.Port[_PortNum].BcTimeStamp = SkOsGetTime(_pAC); \ - _pAC->Rlmt.CheckSwitch = SK_TRUE; \ - } \ - /* _pAC->Rlmt.Port[_PortNum].DataPacketsPerTimeSlot++; */ \ - *(pForRlmt) = SK_RLMT_RX_PROTOCOL; \ - } \ - else if (IsMc) { \ - if (SK_ADDR_EQUAL(_pLaPacket, BridgeMcAddr.a)) { \ - _pAC->Rlmt.Port[_PortNum].BpduPacketsPerTimeSlot++; \ - if (_pAC->Rlmt.Port[_PortNum].Net->RlmtMode & SK_RLMT_CHECK_SEG) { \ - *(pForRlmt) = SK_RLMT_RX_RLMT | SK_RLMT_RX_PROTOCOL; \ - } \ - else { \ - *(pForRlmt) = SK_RLMT_RX_PROTOCOL; \ - } \ - } \ - else if (SK_ADDR_EQUAL(_pLaPacket, SkRlmtMcAddr.a)) { \ - *(pForRlmt) = SK_RLMT_RX_RLMT; \ - } \ - else { \ - /* _pAC->Rlmt.Port[_PortNum].DataPacketsPerTimeSlot++; */ \ - *(pForRlmt) = SK_RLMT_RX_PROTOCOL; \ - } \ - } \ - else { \ - if (SK_ADDR_EQUAL( \ - _pLaPacket, \ - _pAC->Addr.Port[_PortNum].CurrentMacAddress.a)) { \ - *(pForRlmt) = SK_RLMT_RX_RLMT; \ - } \ - else { \ - /* _pAC->Rlmt.Port[_PortNum].DataPacketsPerTimeSlot++; */ \ - *(pForRlmt) = SK_RLMT_RX_PROTOCOL; \ - } \ - } \ -} - -#ifdef SK_RLMT_FAST_LOOKAHEAD -Error: SK_RLMT_FAST_LOOKAHEAD no longer used. Use new macros for lookahead. -#endif /* SK_RLMT_FAST_LOOKAHEAD */ -#ifdef SK_RLMT_SLOW_LOOKAHEAD -Error: SK_RLMT_SLOW_LOOKAHEAD no longer used. Use new macros for lookahead. -#endif /* SK_RLMT_SLOW_LOOKAHEAD */ - -/* typedefs *******************************************************************/ - -#ifdef SK_RLMT_MBUF_PRIVATE -typedef struct s_RlmtMbuf { - some content -} SK_RLMT_MBUF; -#endif /* SK_RLMT_MBUF_PRIVATE */ - - -#ifdef SK_LA_INFO -typedef struct s_Rlmt_PacketInfo { - unsigned PacketLength; /* Length of packet. */ - unsigned PacketType; /* Directed/Multicast/Broadcast. */ -} SK_RLMT_PINFO; -#endif /* SK_LA_INFO */ - - -typedef struct s_RootId { - SK_U8 Id[8]; /* Root Bridge Id. */ -} SK_RLMT_ROOT_ID; - - -typedef struct s_port { - SK_MAC_ADDR CheckAddr; - SK_BOOL SuspectTx; -} SK_PORT_CHECK; - - -typedef struct s_RlmtNet SK_RLMT_NET; - - -typedef struct s_RlmtPort { - -/* ----- Public part (read-only) ----- */ - - SK_U8 PortState; /* Current state of this port. */ - - /* For PNMI */ - SK_BOOL LinkDown; - SK_BOOL PortDown; - SK_U8 Align01; - - SK_U32 PortNumber; /* Number of port on adapter. */ - SK_RLMT_NET * Net; /* Net port belongs to. */ - - SK_U64 TxHelloCts; - SK_U64 RxHelloCts; - SK_U64 TxSpHelloReqCts; - SK_U64 RxSpHelloCts; - -/* ----- Private part ----- */ - -/* SK_U64 PacketsRx; */ /* Total packets received. */ - SK_U32 PacketsPerTimeSlot; /* Packets rxed between TOs. */ -/* SK_U32 DataPacketsPerTimeSlot; */ /* Data packets ... */ - SK_U32 BpduPacketsPerTimeSlot; /* BPDU packets rxed in TS. */ - SK_U64 BcTimeStamp; /* Time of last BC receive. */ - SK_U64 GuTimeStamp; /* Time of entering GOING_UP. */ - - SK_TIMER UpTimer; /* Timer struct Link/Port up. */ - SK_TIMER DownRxTimer; /* Timer struct down rx. */ - SK_TIMER DownTxTimer; /* Timer struct down tx. */ - - SK_U32 CheckingState; /* Checking State. */ - - SK_ADDR_PORT * AddrPort; - - SK_U8 Random[4]; /* Random value. */ - unsigned PortsChecked; /* #ports checked. */ - unsigned PortsSuspect; /* #ports checked that are s. */ - SK_PORT_CHECK PortCheck[1]; -/* SK_PORT_CHECK PortCheck[SK_MAX_MACS - 1]; */ - - SK_BOOL PortStarted; /* Port is started. */ - SK_BOOL PortNoRx; /* NoRx for >= 1 time slot. */ - SK_BOOL RootIdSet; - SK_RLMT_ROOT_ID Root; /* Root Bridge Id. */ -} SK_RLMT_PORT; - - -struct s_RlmtNet { - -/* ----- Public part (read-only) ----- */ - - SK_U32 NetNumber; /* Number of net. */ - - SK_RLMT_PORT * Port[SK_MAX_MACS]; /* Ports that belong to this net. */ - SK_U32 NumPorts; /* Number of ports. */ - SK_U32 PrefPort; /* Preferred port. */ - - /* For PNMI */ - - SK_U32 ChgBcPrio; /* Change Priority of last broadcast received */ - SK_U32 RlmtMode; /* Check ... */ - SK_U32 ActivePort; /* Active port. */ - SK_U32 Preference; /* 0xFFFFFFFF: Automatic. */ - - SK_U8 RlmtState; /* Current RLMT state. */ - -/* ----- Private part ----- */ - SK_BOOL RootIdSet; - SK_U16 Align01; - - int LinksUp; /* #Links up. */ - int PortsUp; /* #Ports up. */ - SK_U32 TimeoutValue; /* RLMT timeout value. */ - - SK_U32 CheckingState; /* Checking State. */ - SK_RLMT_ROOT_ID Root; /* Root Bridge Id. */ - - SK_TIMER LocTimer; /* Timer struct. */ - SK_TIMER SegTimer; /* Timer struct. */ -}; - - -typedef struct s_Rlmt { - -/* ----- Public part (read-only) ----- */ - - SK_U32 NumNets; /* Number of nets. */ - SK_U32 NetsStarted; /* Number of nets started. */ - SK_RLMT_NET Net[SK_MAX_NETS]; /* Array of available nets. */ - SK_RLMT_PORT Port[SK_MAX_MACS]; /* Array of available ports. */ - -/* ----- Private part ----- */ - SK_BOOL CheckSwitch; - SK_BOOL RlmtOff; /* set to zero if the Mac addresses - are equal or the second one - is zero */ - SK_U16 Align01; - -} SK_RLMT; - - -extern SK_MAC_ADDR BridgeMcAddr; -extern SK_MAC_ADDR SkRlmtMcAddr; - -/* function prototypes ********************************************************/ - - -#ifndef SK_KR_PROTO - -/* Functions provided by SkRlmt */ - -/* ANSI/C++ compliant function prototypes */ - -extern void SkRlmtInit( - SK_AC *pAC, - SK_IOC IoC, - int Level); - -extern int SkRlmtEvent( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 Event, - SK_EVPARA Para); - -#else /* defined(SK_KR_PROTO) */ - -/* Non-ANSI/C++ compliant function prototypes */ - -#error KR-style function prototypes are not yet provided. - -#endif /* defined(SK_KR_PROTO)) */ - - -#ifdef __cplusplus -} -#endif /* __cplusplus */ - -#endif /* __INC_SKRLMT_H */ diff --git a/drivers/net/sk98lin/h/sktimer.h b/drivers/net/sk98lin/h/sktimer.h deleted file mode 100644 index 04e6d7c1ec33..000000000000 --- a/drivers/net/sk98lin/h/sktimer.h +++ /dev/null @@ -1,63 +0,0 @@ -/****************************************************************************** - * - * Name: sktimer.h - * Project: Gigabit Ethernet Adapters, Event Scheduler Module - * Version: $Revision: 1.11 $ - * Date: $Date: 2003/09/16 12:58:18 $ - * Purpose: Defines for the timer functions - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * SKTIMER.H contains all defines and types for the timer functions - */ - -#ifndef _SKTIMER_H_ -#define _SKTIMER_H_ - -#include "h/skqueue.h" - -/* - * SK timer - * - needed wherever a timer is used. Put this in your data structure - * wherever you want. - */ -typedef struct s_Timer SK_TIMER; - -struct s_Timer { - SK_TIMER *TmNext; /* linked list */ - SK_U32 TmClass; /* Timer Event class */ - SK_U32 TmEvent; /* Timer Event value */ - SK_EVPARA TmPara; /* Timer Event parameter */ - SK_U32 TmDelta; /* delta time */ - int TmActive; /* flag: active/inactive */ -}; - -/* - * Timer control struct. - * - use in Adapters context name pAC->Tim - */ -typedef struct s_TimCtrl { - SK_TIMER *StQueue; /* Head of Timer queue */ -} SK_TIMCTRL; - -extern void SkTimerInit(SK_AC *pAC, SK_IOC Ioc, int Level); -extern void SkTimerStop(SK_AC *pAC, SK_IOC Ioc, SK_TIMER *pTimer); -extern void SkTimerStart(SK_AC *pAC, SK_IOC Ioc, SK_TIMER *pTimer, - SK_U32 Time, SK_U32 Class, SK_U32 Event, SK_EVPARA Para); -extern void SkTimerDone(SK_AC *pAC, SK_IOC Ioc); -#endif /* _SKTIMER_H_ */ diff --git a/drivers/net/sk98lin/h/sktypes.h b/drivers/net/sk98lin/h/sktypes.h deleted file mode 100644 index 40edc96e1055..000000000000 --- a/drivers/net/sk98lin/h/sktypes.h +++ /dev/null @@ -1,69 +0,0 @@ -/****************************************************************************** - * - * Name: sktypes.h - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.2 $ - * Date: $Date: 2003/10/07 08:16:51 $ - * Purpose: Define data types for Linux - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * In this file, all data types that are needed by the common modules - * are mapped to Linux data types. - * - * - * Include File Hierarchy: - * - * - ******************************************************************************/ - -#ifndef __INC_SKTYPES_H -#define __INC_SKTYPES_H - - -/* defines *******************************************************************/ - -/* - * Data types with a specific size. 'I' = signed, 'U' = unsigned. - */ -#define SK_I8 s8 -#define SK_U8 u8 -#define SK_I16 s16 -#define SK_U16 u16 -#define SK_I32 s32 -#define SK_U32 u32 -#define SK_I64 s64 -#define SK_U64 u64 - -#define SK_UPTR ulong /* casting pointer <-> integral */ - -/* -* Boolean type. -*/ -#define SK_BOOL SK_U8 -#define SK_FALSE 0 -#define SK_TRUE (!SK_FALSE) - -/* typedefs *******************************************************************/ - -/* function prototypes ********************************************************/ - -#endif /* __INC_SKTYPES_H */ diff --git a/drivers/net/sk98lin/h/skversion.h b/drivers/net/sk98lin/h/skversion.h deleted file mode 100644 index a1a7294828e5..000000000000 --- a/drivers/net/sk98lin/h/skversion.h +++ /dev/null @@ -1,38 +0,0 @@ -/****************************************************************************** - * - * Name: version.h - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.5 $ - * Date: $Date: 2003/10/07 08:16:51 $ - * Purpose: SK specific Error log support - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifdef lint -static const char SysKonnectFileId[] = "@(#) (C) SysKonnect GmbH."; -static const char SysKonnectBuildNumber[] = - "@(#)SK-BUILD: 6.23 PL: 01"; -#endif /* !defined(lint) */ - -#define BOOT_STRING "sk98lin: Network Device Driver v6.23\n" \ - "(C)Copyright 1999-2004 Marvell(R)." - -#define VER_STRING "6.23" -#define DRIVER_FILE_NAME "sk98lin" -#define DRIVER_REL_DATE "Feb-13-2004" - - diff --git a/drivers/net/sk98lin/h/skvpd.h b/drivers/net/sk98lin/h/skvpd.h deleted file mode 100644 index fdd9e48e8040..000000000000 --- a/drivers/net/sk98lin/h/skvpd.h +++ /dev/null @@ -1,248 +0,0 @@ -/****************************************************************************** - * - * Name: skvpd.h - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.15 $ - * Date: $Date: 2003/01/13 10:39:38 $ - * Purpose: Defines and Macros for VPD handling - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2003 SysKonnect GmbH. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * skvpd.h contains Diagnostic specific defines for VPD handling - */ - -#ifndef __INC_SKVPD_H_ -#define __INC_SKVPD_H_ - -/* - * Define Resource Type Identifiers and VPD keywords - */ -#define RES_ID 0x82 /* Resource Type ID String (Product Name) */ -#define RES_VPD_R 0x90 /* start of VPD read only area */ -#define RES_VPD_W 0x91 /* start of VPD read/write area */ -#define RES_END 0x78 /* Resource Type End Tag */ - -#ifndef VPD_NAME -#define VPD_NAME "Name" /* Product Name, VPD name of RES_ID */ -#endif /* VPD_NAME */ -#define VPD_PN "PN" /* Adapter Part Number */ -#define VPD_EC "EC" /* Adapter Engineering Level */ -#define VPD_MN "MN" /* Manufacture ID */ -#define VPD_SN "SN" /* Serial Number */ -#define VPD_CP "CP" /* Extended Capability */ -#define VPD_RV "RV" /* Checksum and Reserved */ -#define VPD_YA "YA" /* Asset Tag Identifier */ -#define VPD_VL "VL" /* First Error Log Message (SK specific) */ -#define VPD_VF "VF" /* Second Error Log Message (SK specific) */ -#define VPD_RW "RW" /* Remaining Read / Write Area */ - -/* 'type' values for vpd_setup_para() */ -#define VPD_RO_KEY 1 /* RO keys are "PN", "EC", "MN", "SN", "RV" */ -#define VPD_RW_KEY 2 /* RW keys are "Yx", "Vx", and "RW" */ - -/* 'op' values for vpd_setup_para() */ -#define ADD_KEY 1 /* add the key at the pos "RV" or "RW" */ -#define OWR_KEY 2 /* overwrite key if already exists */ - -/* - * Define READ and WRITE Constants. - */ - -#define VPD_DEV_ID_GENESIS 0x4300 - -#define VPD_SIZE_YUKON 256 -#define VPD_SIZE_GENESIS 512 -#define VPD_SIZE 512 -#define VPD_READ 0x0000 -#define VPD_WRITE 0x8000 - -#define VPD_STOP(pAC,IoC) VPD_OUT16(pAC,IoC,PCI_VPD_ADR_REG,VPD_WRITE) - -#define VPD_GET_RES_LEN(p) ((unsigned int) \ - (* (SK_U8 *)&(p)[1]) |\ - ((* (SK_U8 *)&(p)[2]) << 8)) -#define VPD_GET_VPD_LEN(p) ((unsigned int)(* (SK_U8 *)&(p)[2])) -#define VPD_GET_VAL(p) ((char *)&(p)[3]) - -#define VPD_MAX_LEN 50 - -/* VPD status */ - /* bit 7..1 reserved */ -#define VPD_VALID (1<<0) /* VPD data buffer, vpd_free_ro, */ - /* and vpd_free_rw valid */ - -/* - * VPD structs - */ -typedef struct s_vpd_status { - unsigned short Align01; /* Alignment */ - unsigned short vpd_status; /* VPD status, description see above */ - int vpd_free_ro; /* unused bytes in read only area */ - int vpd_free_rw; /* bytes available in read/write area */ -} SK_VPD_STATUS; - -typedef struct s_vpd { - SK_VPD_STATUS v; /* VPD status structure */ - char vpd_buf[VPD_SIZE]; /* VPD buffer */ - int rom_size; /* VPD ROM Size from PCI_OUR_REG_2 */ - int vpd_size; /* saved VPD-size */ -} SK_VPD; - -typedef struct s_vpd_para { - unsigned int p_len; /* parameter length */ - char *p_val; /* points to the value */ -} SK_VPD_PARA; - -/* - * structure of Large Resource Type Identifiers - */ - -/* was removed because of alignment problems */ - -/* - * structure of VPD keywords - */ -typedef struct s_vpd_key { - char p_key[2]; /* 2 bytes ID string */ - unsigned char p_len; /* 1 byte length */ - char p_val; /* start of the value string */ -} SK_VPD_KEY; - - -/* - * System specific VPD macros - */ -#ifndef SKDIAG -#ifndef VPD_DO_IO -#define VPD_OUT8(pAC,IoC,Addr,Val) (void)SkPciWriteCfgByte(pAC,Addr,Val) -#define VPD_OUT16(pAC,IoC,Addr,Val) (void)SkPciWriteCfgWord(pAC,Addr,Val) -#define VPD_IN8(pAC,IoC,Addr,pVal) (void)SkPciReadCfgByte(pAC,Addr,pVal) -#define VPD_IN16(pAC,IoC,Addr,pVal) (void)SkPciReadCfgWord(pAC,Addr,pVal) -#define VPD_IN32(pAC,IoC,Addr,pVal) (void)SkPciReadCfgDWord(pAC,Addr,pVal) -#else /* VPD_DO_IO */ -#define VPD_OUT8(pAC,IoC,Addr,Val) SK_OUT8(IoC,PCI_C(Addr),Val) -#define VPD_OUT16(pAC,IoC,Addr,Val) SK_OUT16(IoC,PCI_C(Addr),Val) -#define VPD_IN8(pAC,IoC,Addr,pVal) SK_IN8(IoC,PCI_C(Addr),pVal) -#define VPD_IN16(pAC,IoC,Addr,pVal) SK_IN16(IoC,PCI_C(Addr),pVal) -#define VPD_IN32(pAC,IoC,Addr,pVal) SK_IN32(IoC,PCI_C(Addr),pVal) -#endif /* VPD_DO_IO */ -#else /* SKDIAG */ -#define VPD_OUT8(pAC,Ioc,Addr,Val) { \ - if ((pAC)->DgT.DgUseCfgCycle) \ - SkPciWriteCfgByte(pAC,Addr,Val); \ - else \ - SK_OUT8(pAC,PCI_C(Addr),Val); \ - } -#define VPD_OUT16(pAC,Ioc,Addr,Val) { \ - if ((pAC)->DgT.DgUseCfgCycle) \ - SkPciWriteCfgWord(pAC,Addr,Val); \ - else \ - SK_OUT16(pAC,PCI_C(Addr),Val); \ - } -#define VPD_IN8(pAC,Ioc,Addr,pVal) { \ - if ((pAC)->DgT.DgUseCfgCycle) \ - SkPciReadCfgByte(pAC,Addr,pVal); \ - else \ - SK_IN8(pAC,PCI_C(Addr),pVal); \ - } -#define VPD_IN16(pAC,Ioc,Addr,pVal) { \ - if ((pAC)->DgT.DgUseCfgCycle) \ - SkPciReadCfgWord(pAC,Addr,pVal); \ - else \ - SK_IN16(pAC,PCI_C(Addr),pVal); \ - } -#define VPD_IN32(pAC,Ioc,Addr,pVal) { \ - if ((pAC)->DgT.DgUseCfgCycle) \ - SkPciReadCfgDWord(pAC,Addr,pVal); \ - else \ - SK_IN32(pAC,PCI_C(Addr),pVal); \ - } -#endif /* nSKDIAG */ - -/* function prototypes ********************************************************/ - -#ifndef SK_KR_PROTO -#ifdef SKDIAG -extern SK_U32 VpdReadDWord( - SK_AC *pAC, - SK_IOC IoC, - int addr); -#endif /* SKDIAG */ - -extern SK_VPD_STATUS *VpdStat( - SK_AC *pAC, - SK_IOC IoC); - -extern int VpdKeys( - SK_AC *pAC, - SK_IOC IoC, - char *buf, - int *len, - int *elements); - -extern int VpdRead( - SK_AC *pAC, - SK_IOC IoC, - const char *key, - char *buf, - int *len); - -extern SK_BOOL VpdMayWrite( - char *key); - -extern int VpdWrite( - SK_AC *pAC, - SK_IOC IoC, - const char *key, - const char *buf); - -extern int VpdDelete( - SK_AC *pAC, - SK_IOC IoC, - char *key); - -extern int VpdUpdate( - SK_AC *pAC, - SK_IOC IoC); - -#ifdef SKDIAG -extern int VpdReadBlock( - SK_AC *pAC, - SK_IOC IoC, - char *buf, - int addr, - int len); - -extern int VpdWriteBlock( - SK_AC *pAC, - SK_IOC IoC, - char *buf, - int addr, - int len); -#endif /* SKDIAG */ -#else /* SK_KR_PROTO */ -extern SK_U32 VpdReadDWord(); -extern SK_VPD_STATUS *VpdStat(); -extern int VpdKeys(); -extern int VpdRead(); -extern SK_BOOL VpdMayWrite(); -extern int VpdWrite(); -extern int VpdDelete(); -extern int VpdUpdate(); -#endif /* SK_KR_PROTO */ - -#endif /* __INC_SKVPD_H_ */ diff --git a/drivers/net/sk98lin/h/xmac_ii.h b/drivers/net/sk98lin/h/xmac_ii.h deleted file mode 100644 index 7f8e6d0084c7..000000000000 --- a/drivers/net/sk98lin/h/xmac_ii.h +++ /dev/null @@ -1,1579 +0,0 @@ -/****************************************************************************** - * - * Name: xmac_ii.h - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.52 $ - * Date: $Date: 2003/10/02 16:35:50 $ - * Purpose: Defines and Macros for Gigabit Ethernet Controller - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#ifndef __INC_XMAC_H -#define __INC_XMAC_H - -#ifdef __cplusplus -extern "C" { -#endif /* __cplusplus */ - -/* defines ********************************************************************/ - -/* - * XMAC II registers - * - * The XMAC registers are 16 or 32 bits wide. - * The XMACs host processor interface is set to 16 bit mode, - * therefore ALL registers will be addressed with 16 bit accesses. - * - * The following macros are provided to access the XMAC registers - * XM_IN16(), XM_OUT16, XM_IN32(), XM_OUT32(), XM_INADR(), XM_OUTADR(), - * XM_INHASH(), and XM_OUTHASH(). - * The macros are defined in SkGeHw.h. - * - * Note: NA reg = Network Address e.g DA, SA etc. - * - */ -#define XM_MMU_CMD 0x0000 /* 16 bit r/w MMU Command Register */ - /* 0x0004: reserved */ -#define XM_POFF 0x0008 /* 32 bit r/w Packet Offset Register */ -#define XM_BURST 0x000c /* 32 bit r/w Burst Register for half duplex*/ -#define XM_1L_VLAN_TAG 0x0010 /* 16 bit r/w One Level VLAN Tag ID */ -#define XM_2L_VLAN_TAG 0x0014 /* 16 bit r/w Two Level VLAN Tag ID */ - /* 0x0018 - 0x001e: reserved */ -#define XM_TX_CMD 0x0020 /* 16 bit r/w Transmit Command Register */ -#define XM_TX_RT_LIM 0x0024 /* 16 bit r/w Transmit Retry Limit Register */ -#define XM_TX_STIME 0x0028 /* 16 bit r/w Transmit Slottime Register */ -#define XM_TX_IPG 0x002c /* 16 bit r/w Transmit Inter Packet Gap */ -#define XM_RX_CMD 0x0030 /* 16 bit r/w Receive Command Register */ -#define XM_PHY_ADDR 0x0034 /* 16 bit r/w PHY Address Register */ -#define XM_PHY_DATA 0x0038 /* 16 bit r/w PHY Data Register */ - /* 0x003c: reserved */ -#define XM_GP_PORT 0x0040 /* 32 bit r/w General Purpose Port Register */ -#define XM_IMSK 0x0044 /* 16 bit r/w Interrupt Mask Register */ -#define XM_ISRC 0x0048 /* 16 bit r/o Interrupt Status Register */ -#define XM_HW_CFG 0x004c /* 16 bit r/w Hardware Config Register */ - /* 0x0050 - 0x005e: reserved */ -#define XM_TX_LO_WM 0x0060 /* 16 bit r/w Tx FIFO Low Water Mark */ -#define XM_TX_HI_WM 0x0062 /* 16 bit r/w Tx FIFO High Water Mark */ -#define XM_TX_THR 0x0064 /* 16 bit r/w Tx Request Threshold */ -#define XM_HT_THR 0x0066 /* 16 bit r/w Host Request Threshold */ -#define XM_PAUSE_DA 0x0068 /* NA reg r/w Pause Destination Address */ - /* 0x006e: reserved */ -#define XM_CTL_PARA 0x0070 /* 32 bit r/w Control Parameter Register */ -#define XM_MAC_OPCODE 0x0074 /* 16 bit r/w Opcode for MAC control frames */ -#define XM_MAC_PTIME 0x0076 /* 16 bit r/w Pause time for MAC ctrl frames*/ -#define XM_TX_STAT 0x0078 /* 32 bit r/o Tx Status LIFO Register */ - - /* 0x0080 - 0x00fc: 16 NA reg r/w Exact Match Address Registers */ - /* use the XM_EXM() macro to address */ -#define XM_EXM_START 0x0080 /* r/w Start Address of the EXM Regs */ - - /* - * XM_EXM(Reg) - * - * returns the XMAC address offset of specified Exact Match Addr Reg - * - * para: Reg EXM register to addr (0 .. 15) - * - * usage: XM_INADDR(IoC, MAC_1, XM_EXM(i), &val[i]); - */ -#define XM_EXM(Reg) (XM_EXM_START + ((Reg) << 3)) - -#define XM_SRC_CHK 0x0100 /* NA reg r/w Source Check Address Register */ -#define XM_SA 0x0108 /* NA reg r/w Station Address Register */ -#define XM_HSM 0x0110 /* 64 bit r/w Hash Match Address Registers */ -#define XM_RX_LO_WM 0x0118 /* 16 bit r/w Receive Low Water Mark */ -#define XM_RX_HI_WM 0x011a /* 16 bit r/w Receive High Water Mark */ -#define XM_RX_THR 0x011c /* 32 bit r/w Receive Request Threshold */ -#define XM_DEV_ID 0x0120 /* 32 bit r/o Device ID Register */ -#define XM_MODE 0x0124 /* 32 bit r/w Mode Register */ -#define XM_LSA 0x0128 /* NA reg r/o Last Source Register */ - /* 0x012e: reserved */ -#define XM_TS_READ 0x0130 /* 32 bit r/o Time Stamp Read Register */ -#define XM_TS_LOAD 0x0134 /* 32 bit r/o Time Stamp Load Value */ - /* 0x0138 - 0x01fe: reserved */ -#define XM_STAT_CMD 0x0200 /* 16 bit r/w Statistics Command Register */ -#define XM_RX_CNT_EV 0x0204 /* 32 bit r/o Rx Counter Event Register */ -#define XM_TX_CNT_EV 0x0208 /* 32 bit r/o Tx Counter Event Register */ -#define XM_RX_EV_MSK 0x020c /* 32 bit r/w Rx Counter Event Mask */ -#define XM_TX_EV_MSK 0x0210 /* 32 bit r/w Tx Counter Event Mask */ - /* 0x0204 - 0x027e: reserved */ -#define XM_TXF_OK 0x0280 /* 32 bit r/o Frames Transmitted OK Conuter */ -#define XM_TXO_OK_HI 0x0284 /* 32 bit r/o Octets Transmitted OK High Cnt*/ -#define XM_TXO_OK_LO 0x0288 /* 32 bit r/o Octets Transmitted OK Low Cnt */ -#define XM_TXF_BC_OK 0x028c /* 32 bit r/o Broadcast Frames Xmitted OK */ -#define XM_TXF_MC_OK 0x0290 /* 32 bit r/o Multicast Frames Xmitted OK */ -#define XM_TXF_UC_OK 0x0294 /* 32 bit r/o Unicast Frames Xmitted OK */ -#define XM_TXF_LONG 0x0298 /* 32 bit r/o Tx Long Frame Counter */ -#define XM_TXE_BURST 0x029c /* 32 bit r/o Tx Burst Event Counter */ -#define XM_TXF_MPAUSE 0x02a0 /* 32 bit r/o Tx Pause MAC Ctrl Frame Cnt */ -#define XM_TXF_MCTRL 0x02a4 /* 32 bit r/o Tx MAC Ctrl Frame Counter */ -#define XM_TXF_SNG_COL 0x02a8 /* 32 bit r/o Tx Single Collision Counter */ -#define XM_TXF_MUL_COL 0x02ac /* 32 bit r/o Tx Multiple Collision Counter */ -#define XM_TXF_ABO_COL 0x02b0 /* 32 bit r/o Tx aborted due to Exces. Col. */ -#define XM_TXF_LAT_COL 0x02b4 /* 32 bit r/o Tx Late Collision Counter */ -#define XM_TXF_DEF 0x02b8 /* 32 bit r/o Tx Deferred Frame Counter */ -#define XM_TXF_EX_DEF 0x02bc /* 32 bit r/o Tx Excessive Deferall Counter */ -#define XM_TXE_FIFO_UR 0x02c0 /* 32 bit r/o Tx FIFO Underrun Event Cnt */ -#define XM_TXE_CS_ERR 0x02c4 /* 32 bit r/o Tx Carrier Sense Error Cnt */ -#define XM_TXP_UTIL 0x02c8 /* 32 bit r/o Tx Utilization in % */ - /* 0x02cc - 0x02ce: reserved */ -#define XM_TXF_64B 0x02d0 /* 32 bit r/o 64 Byte Tx Frame Counter */ -#define XM_TXF_127B 0x02d4 /* 32 bit r/o 65-127 Byte Tx Frame Counter */ -#define XM_TXF_255B 0x02d8 /* 32 bit r/o 128-255 Byte Tx Frame Counter */ -#define XM_TXF_511B 0x02dc /* 32 bit r/o 256-511 Byte Tx Frame Counter */ -#define XM_TXF_1023B 0x02e0 /* 32 bit r/o 512-1023 Byte Tx Frame Counter*/ -#define XM_TXF_MAX_SZ 0x02e4 /* 32 bit r/o 1024-MaxSize Byte Tx Frame Cnt*/ - /* 0x02e8 - 0x02fe: reserved */ -#define XM_RXF_OK 0x0300 /* 32 bit r/o Frames Received OK */ -#define XM_RXO_OK_HI 0x0304 /* 32 bit r/o Octets Received OK High Cnt */ -#define XM_RXO_OK_LO 0x0308 /* 32 bit r/o Octets Received OK Low Counter*/ -#define XM_RXF_BC_OK 0x030c /* 32 bit r/o Broadcast Frames Received OK */ -#define XM_RXF_MC_OK 0x0310 /* 32 bit r/o Multicast Frames Received OK */ -#define XM_RXF_UC_OK 0x0314 /* 32 bit r/o Unicast Frames Received OK */ -#define XM_RXF_MPAUSE 0x0318 /* 32 bit r/o Rx Pause MAC Ctrl Frame Cnt */ -#define XM_RXF_MCTRL 0x031c /* 32 bit r/o Rx MAC Ctrl Frame Counter */ -#define XM_RXF_INV_MP 0x0320 /* 32 bit r/o Rx invalid Pause Frame Cnt */ -#define XM_RXF_INV_MOC 0x0324 /* 32 bit r/o Rx Frames with inv. MAC Opcode*/ -#define XM_RXE_BURST 0x0328 /* 32 bit r/o Rx Burst Event Counter */ -#define XM_RXE_FMISS 0x032c /* 32 bit r/o Rx Missed Frames Event Cnt */ -#define XM_RXF_FRA_ERR 0x0330 /* 32 bit r/o Rx Framing Error Counter */ -#define XM_RXE_FIFO_OV 0x0334 /* 32 bit r/o Rx FIFO overflow Event Cnt */ -#define XM_RXF_JAB_PKT 0x0338 /* 32 bit r/o Rx Jabber Packet Frame Cnt */ -#define XM_RXE_CAR_ERR 0x033c /* 32 bit r/o Rx Carrier Event Error Cnt */ -#define XM_RXF_LEN_ERR 0x0340 /* 32 bit r/o Rx in Range Length Error */ -#define XM_RXE_SYM_ERR 0x0344 /* 32 bit r/o Rx Symbol Error Counter */ -#define XM_RXE_SHT_ERR 0x0348 /* 32 bit r/o Rx Short Event Error Cnt */ -#define XM_RXE_RUNT 0x034c /* 32 bit r/o Rx Runt Event Counter */ -#define XM_RXF_LNG_ERR 0x0350 /* 32 bit r/o Rx Frame too Long Error Cnt */ -#define XM_RXF_FCS_ERR 0x0354 /* 32 bit r/o Rx Frame Check Seq. Error Cnt */ - /* 0x0358 - 0x035a: reserved */ -#define XM_RXF_CEX_ERR 0x035c /* 32 bit r/o Rx Carrier Ext Error Frame Cnt*/ -#define XM_RXP_UTIL 0x0360 /* 32 bit r/o Rx Utilization in % */ - /* 0x0364 - 0x0366: reserved */ -#define XM_RXF_64B 0x0368 /* 32 bit r/o 64 Byte Rx Frame Counter */ -#define XM_RXF_127B 0x036c /* 32 bit r/o 65-127 Byte Rx Frame Counter */ -#define XM_RXF_255B 0x0370 /* 32 bit r/o 128-255 Byte Rx Frame Counter */ -#define XM_RXF_511B 0x0374 /* 32 bit r/o 256-511 Byte Rx Frame Counter */ -#define XM_RXF_1023B 0x0378 /* 32 bit r/o 512-1023 Byte Rx Frame Counter*/ -#define XM_RXF_MAX_SZ 0x037c /* 32 bit r/o 1024-MaxSize Byte Rx Frame Cnt*/ - /* 0x02e8 - 0x02fe: reserved */ - - -/*----------------------------------------------------------------------------*/ -/* - * XMAC Bit Definitions - * - * If the bit access behaviour differs from the register access behaviour - * (r/w, r/o) this is documented after the bit number. - * The following bit access behaviours are used: - * (sc) self clearing - * (ro) read only - */ - -/* XM_MMU_CMD 16 bit r/w MMU Command Register */ - /* Bit 15..13: reserved */ -#define XM_MMU_PHY_RDY (1<<12) /* Bit 12: PHY Read Ready */ -#define XM_MMU_PHY_BUSY (1<<11) /* Bit 11: PHY Busy */ -#define XM_MMU_IGN_PF (1<<10) /* Bit 10: Ignore Pause Frame */ -#define XM_MMU_MAC_LB (1<<9) /* Bit 9: Enable MAC Loopback */ - /* Bit 8: reserved */ -#define XM_MMU_FRC_COL (1<<7) /* Bit 7: Force Collision */ -#define XM_MMU_SIM_COL (1<<6) /* Bit 6: Simulate Collision */ -#define XM_MMU_NO_PRE (1<<5) /* Bit 5: No MDIO Preamble */ -#define XM_MMU_GMII_FD (1<<4) /* Bit 4: GMII uses Full Duplex */ -#define XM_MMU_RAT_CTRL (1<<3) /* Bit 3: Enable Rate Control */ -#define XM_MMU_GMII_LOOP (1<<2) /* Bit 2: PHY is in Loopback Mode */ -#define XM_MMU_ENA_RX (1<<1) /* Bit 1: Enable Receiver */ -#define XM_MMU_ENA_TX (1<<0) /* Bit 0: Enable Transmitter */ - - -/* XM_TX_CMD 16 bit r/w Transmit Command Register */ - /* Bit 15..7: reserved */ -#define XM_TX_BK2BK (1<<6) /* Bit 6: Ignor Carrier Sense (Tx Bk2Bk)*/ -#define XM_TX_ENC_BYP (1<<5) /* Bit 5: Set Encoder in Bypass Mode */ -#define XM_TX_SAM_LINE (1<<4) /* Bit 4: (sc) Start utilization calculation */ -#define XM_TX_NO_GIG_MD (1<<3) /* Bit 3: Disable Carrier Extension */ -#define XM_TX_NO_PRE (1<<2) /* Bit 2: Disable Preamble Generation */ -#define XM_TX_NO_CRC (1<<1) /* Bit 1: Disable CRC Generation */ -#define XM_TX_AUTO_PAD (1<<0) /* Bit 0: Enable Automatic Padding */ - - -/* XM_TX_RT_LIM 16 bit r/w Transmit Retry Limit Register */ - /* Bit 15..5: reserved */ -#define XM_RT_LIM_MSK 0x1f /* Bit 4..0: Tx Retry Limit */ - - -/* XM_TX_STIME 16 bit r/w Transmit Slottime Register */ - /* Bit 15..7: reserved */ -#define XM_STIME_MSK 0x7f /* Bit 6..0: Tx Slottime bits */ - - -/* XM_TX_IPG 16 bit r/w Transmit Inter Packet Gap */ - /* Bit 15..8: reserved */ -#define XM_IPG_MSK 0xff /* Bit 7..0: IPG value bits */ - - -/* XM_RX_CMD 16 bit r/w Receive Command Register */ - /* Bit 15..9: reserved */ -#define XM_RX_LENERR_OK (1<<8) /* Bit 8 don't set Rx Err bit for */ - /* inrange error packets */ -#define XM_RX_BIG_PK_OK (1<<7) /* Bit 7 don't set Rx Err bit for */ - /* jumbo packets */ -#define XM_RX_IPG_CAP (1<<6) /* Bit 6 repl. type field with IPG */ -#define XM_RX_TP_MD (1<<5) /* Bit 5: Enable transparent Mode */ -#define XM_RX_STRIP_FCS (1<<4) /* Bit 4: Enable FCS Stripping */ -#define XM_RX_SELF_RX (1<<3) /* Bit 3: Enable Rx of own packets */ -#define XM_RX_SAM_LINE (1<<2) /* Bit 2: (sc) Start utilization calculation */ -#define XM_RX_STRIP_PAD (1<<1) /* Bit 1: Strip pad bytes of Rx frames */ -#define XM_RX_DIS_CEXT (1<<0) /* Bit 0: Disable carrier ext. check */ - - -/* XM_PHY_ADDR 16 bit r/w PHY Address Register */ - /* Bit 15..5: reserved */ -#define XM_PHY_ADDR_SZ 0x1f /* Bit 4..0: PHY Address bits */ - - -/* XM_GP_PORT 32 bit r/w General Purpose Port Register */ - /* Bit 31..7: reserved */ -#define XM_GP_ANIP (1L<<6) /* Bit 6: (ro) Auto-Neg. in progress */ -#define XM_GP_FRC_INT (1L<<5) /* Bit 5: (sc) Force Interrupt */ - /* Bit 4: reserved */ -#define XM_GP_RES_MAC (1L<<3) /* Bit 3: (sc) Reset MAC and FIFOs */ -#define XM_GP_RES_STAT (1L<<2) /* Bit 2: (sc) Reset the statistics module */ - /* Bit 1: reserved */ -#define XM_GP_INP_ASS (1L<<0) /* Bit 0: (ro) GP Input Pin asserted */ - - -/* XM_IMSK 16 bit r/w Interrupt Mask Register */ -/* XM_ISRC 16 bit r/o Interrupt Status Register */ - /* Bit 15: reserved */ -#define XM_IS_LNK_AE (1<<14) /* Bit 14: Link Asynchronous Event */ -#define XM_IS_TX_ABORT (1<<13) /* Bit 13: Transmit Abort, late Col. etc */ -#define XM_IS_FRC_INT (1<<12) /* Bit 12: Force INT bit set in GP */ -#define XM_IS_INP_ASS (1<<11) /* Bit 11: Input Asserted, GP bit 0 set */ -#define XM_IS_LIPA_RC (1<<10) /* Bit 10: Link Partner requests config */ -#define XM_IS_RX_PAGE (1<<9) /* Bit 9: Page Received */ -#define XM_IS_TX_PAGE (1<<8) /* Bit 8: Next Page Loaded for Transmit */ -#define XM_IS_AND (1<<7) /* Bit 7: Auto-Negotiation Done */ -#define XM_IS_TSC_OV (1<<6) /* Bit 6: Time Stamp Counter Overflow */ -#define XM_IS_RXC_OV (1<<5) /* Bit 5: Rx Counter Event Overflow */ -#define XM_IS_TXC_OV (1<<4) /* Bit 4: Tx Counter Event Overflow */ -#define XM_IS_RXF_OV (1<<3) /* Bit 3: Receive FIFO Overflow */ -#define XM_IS_TXF_UR (1<<2) /* Bit 2: Transmit FIFO Underrun */ -#define XM_IS_TX_COMP (1<<1) /* Bit 1: Frame Tx Complete */ -#define XM_IS_RX_COMP (1<<0) /* Bit 0: Frame Rx Complete */ - -#define XM_DEF_MSK (~(XM_IS_INP_ASS | XM_IS_LIPA_RC | XM_IS_RX_PAGE |\ - XM_IS_AND | XM_IS_RXC_OV | XM_IS_TXC_OV | XM_IS_TXF_UR)) - - -/* XM_HW_CFG 16 bit r/w Hardware Config Register */ - /* Bit 15.. 4: reserved */ -#define XM_HW_GEN_EOP (1<<3) /* Bit 3: generate End of Packet pulse */ -#define XM_HW_COM4SIG (1<<2) /* Bit 2: use Comma Detect for Sig. Det.*/ - /* Bit 1: reserved */ -#define XM_HW_GMII_MD (1<<0) /* Bit 0: GMII Interface selected */ - - -/* XM_TX_LO_WM 16 bit r/w Tx FIFO Low Water Mark */ -/* XM_TX_HI_WM 16 bit r/w Tx FIFO High Water Mark */ - /* Bit 15..10 reserved */ -#define XM_TX_WM_MSK 0x01ff /* Bit 9.. 0 Tx FIFO Watermark bits */ - -/* XM_TX_THR 16 bit r/w Tx Request Threshold */ -/* XM_HT_THR 16 bit r/w Host Request Threshold */ -/* XM_RX_THR 16 bit r/w Rx Request Threshold */ - /* Bit 15..11 reserved */ -#define XM_THR_MSK 0x03ff /* Bit 10.. 0 Rx/Tx Request Threshold bits */ - - -/* XM_TX_STAT 32 bit r/o Tx Status LIFO Register */ -#define XM_ST_VALID (1UL<<31) /* Bit 31: Status Valid */ -#define XM_ST_BYTE_CNT (0x3fffL<<17) /* Bit 30..17: Tx frame Length */ -#define XM_ST_RETRY_CNT (0x1fL<<12) /* Bit 16..12: Retry Count */ -#define XM_ST_EX_COL (1L<<11) /* Bit 11: Excessive Collisions */ -#define XM_ST_EX_DEF (1L<<10) /* Bit 10: Excessive Deferral */ -#define XM_ST_BURST (1L<<9) /* Bit 9: p. xmitted in burst md*/ -#define XM_ST_DEFER (1L<<8) /* Bit 8: packet was defered */ -#define XM_ST_BC (1L<<7) /* Bit 7: Broadcast packet */ -#define XM_ST_MC (1L<<6) /* Bit 6: Multicast packet */ -#define XM_ST_UC (1L<<5) /* Bit 5: Unicast packet */ -#define XM_ST_TX_UR (1L<<4) /* Bit 4: FIFO Underrun occured */ -#define XM_ST_CS_ERR (1L<<3) /* Bit 3: Carrier Sense Error */ -#define XM_ST_LAT_COL (1L<<2) /* Bit 2: Late Collision Error */ -#define XM_ST_MUL_COL (1L<<1) /* Bit 1: Multiple Collisions */ -#define XM_ST_SGN_COL (1L<<0) /* Bit 0: Single Collision */ - -/* XM_RX_LO_WM 16 bit r/w Receive Low Water Mark */ -/* XM_RX_HI_WM 16 bit r/w Receive High Water Mark */ - /* Bit 15..11: reserved */ -#define XM_RX_WM_MSK 0x03ff /* Bit 11.. 0: Rx FIFO Watermark bits */ - - -/* XM_DEV_ID 32 bit r/o Device ID Register */ -#define XM_DEV_OUI (0x00ffffffUL<<8) /* Bit 31..8: Device OUI */ -#define XM_DEV_REV (0x07L << 5) /* Bit 7..5: Chip Rev Num */ - - -/* XM_MODE 32 bit r/w Mode Register */ - /* Bit 31..27: reserved */ -#define XM_MD_ENA_REJ (1L<<26) /* Bit 26: Enable Frame Reject */ -#define XM_MD_SPOE_E (1L<<25) /* Bit 25: Send Pause on Edge */ - /* extern generated */ -#define XM_MD_TX_REP (1L<<24) /* Bit 24: Transmit Repeater Mode */ -#define XM_MD_SPOFF_I (1L<<23) /* Bit 23: Send Pause on FIFO full */ - /* intern generated */ -#define XM_MD_LE_STW (1L<<22) /* Bit 22: Rx Stat Word in Little Endian */ -#define XM_MD_TX_CONT (1L<<21) /* Bit 21: Send Continuous */ -#define XM_MD_TX_PAUSE (1L<<20) /* Bit 20: (sc) Send Pause Frame */ -#define XM_MD_ATS (1L<<19) /* Bit 19: Append Time Stamp */ -#define XM_MD_SPOL_I (1L<<18) /* Bit 18: Send Pause on Low */ - /* intern generated */ -#define XM_MD_SPOH_I (1L<<17) /* Bit 17: Send Pause on High */ - /* intern generated */ -#define XM_MD_CAP (1L<<16) /* Bit 16: Check Address Pair */ -#define XM_MD_ENA_HASH (1L<<15) /* Bit 15: Enable Hashing */ -#define XM_MD_CSA (1L<<14) /* Bit 14: Check Station Address */ -#define XM_MD_CAA (1L<<13) /* Bit 13: Check Address Array */ -#define XM_MD_RX_MCTRL (1L<<12) /* Bit 12: Rx MAC Control Frame */ -#define XM_MD_RX_RUNT (1L<<11) /* Bit 11: Rx Runt Frames */ -#define XM_MD_RX_IRLE (1L<<10) /* Bit 10: Rx in Range Len Err Frame */ -#define XM_MD_RX_LONG (1L<<9) /* Bit 9: Rx Long Frame */ -#define XM_MD_RX_CRCE (1L<<8) /* Bit 8: Rx CRC Error Frame */ -#define XM_MD_RX_ERR (1L<<7) /* Bit 7: Rx Error Frame */ -#define XM_MD_DIS_UC (1L<<6) /* Bit 6: Disable Rx Unicast */ -#define XM_MD_DIS_MC (1L<<5) /* Bit 5: Disable Rx Multicast */ -#define XM_MD_DIS_BC (1L<<4) /* Bit 4: Disable Rx Broadcast */ -#define XM_MD_ENA_PROM (1L<<3) /* Bit 3: Enable Promiscuous */ -#define XM_MD_ENA_BE (1L<<2) /* Bit 2: Enable Big Endian */ -#define XM_MD_FTF (1L<<1) /* Bit 1: (sc) Flush Tx FIFO */ -#define XM_MD_FRF (1L<<0) /* Bit 0: (sc) Flush Rx FIFO */ - -#define XM_PAUSE_MODE (XM_MD_SPOE_E | XM_MD_SPOL_I | XM_MD_SPOH_I) -#define XM_DEF_MODE (XM_MD_RX_RUNT | XM_MD_RX_IRLE | XM_MD_RX_LONG |\ - XM_MD_RX_CRCE | XM_MD_RX_ERR | XM_MD_CSA | XM_MD_CAA) - -/* XM_STAT_CMD 16 bit r/w Statistics Command Register */ - /* Bit 16..6: reserved */ -#define XM_SC_SNP_RXC (1<<5) /* Bit 5: (sc) Snap Rx Counters */ -#define XM_SC_SNP_TXC (1<<4) /* Bit 4: (sc) Snap Tx Counters */ -#define XM_SC_CP_RXC (1<<3) /* Bit 3: Copy Rx Counters Continuously */ -#define XM_SC_CP_TXC (1<<2) /* Bit 2: Copy Tx Counters Continuously */ -#define XM_SC_CLR_RXC (1<<1) /* Bit 1: (sc) Clear Rx Counters */ -#define XM_SC_CLR_TXC (1<<0) /* Bit 0: (sc) Clear Tx Counters */ - - -/* XM_RX_CNT_EV 32 bit r/o Rx Counter Event Register */ -/* XM_RX_EV_MSK 32 bit r/w Rx Counter Event Mask */ -#define XMR_MAX_SZ_OV (1UL<<31) /* Bit 31: 1024-MaxSize Rx Cnt Ov*/ -#define XMR_1023B_OV (1L<<30) /* Bit 30: 512-1023Byte Rx Cnt Ov*/ -#define XMR_511B_OV (1L<<29) /* Bit 29: 256-511 Byte Rx Cnt Ov*/ -#define XMR_255B_OV (1L<<28) /* Bit 28: 128-255 Byte Rx Cnt Ov*/ -#define XMR_127B_OV (1L<<27) /* Bit 27: 65-127 Byte Rx Cnt Ov */ -#define XMR_64B_OV (1L<<26) /* Bit 26: 64 Byte Rx Cnt Ov */ -#define XMR_UTIL_OV (1L<<25) /* Bit 25: Rx Util Cnt Overflow */ -#define XMR_UTIL_UR (1L<<24) /* Bit 24: Rx Util Cnt Underrun */ -#define XMR_CEX_ERR_OV (1L<<23) /* Bit 23: CEXT Err Cnt Ov */ - /* Bit 22: reserved */ -#define XMR_FCS_ERR_OV (1L<<21) /* Bit 21: Rx FCS Error Cnt Ov */ -#define XMR_LNG_ERR_OV (1L<<20) /* Bit 20: Rx too Long Err Cnt Ov*/ -#define XMR_RUNT_OV (1L<<19) /* Bit 19: Runt Event Cnt Ov */ -#define XMR_SHT_ERR_OV (1L<<18) /* Bit 18: Rx Short Ev Err Cnt Ov*/ -#define XMR_SYM_ERR_OV (1L<<17) /* Bit 17: Rx Sym Err Cnt Ov */ - /* Bit 16: reserved */ -#define XMR_CAR_ERR_OV (1L<<15) /* Bit 15: Rx Carr Ev Err Cnt Ov */ -#define XMR_JAB_PKT_OV (1L<<14) /* Bit 14: Rx Jabb Packet Cnt Ov */ -#define XMR_FIFO_OV (1L<<13) /* Bit 13: Rx FIFO Ov Ev Cnt Ov */ -#define XMR_FRA_ERR_OV (1L<<12) /* Bit 12: Rx Framing Err Cnt Ov */ -#define XMR_FMISS_OV (1L<<11) /* Bit 11: Rx Missed Ev Cnt Ov */ -#define XMR_BURST (1L<<10) /* Bit 10: Rx Burst Event Cnt Ov */ -#define XMR_INV_MOC (1L<<9) /* Bit 9: Rx with inv. MAC OC Ov*/ -#define XMR_INV_MP (1L<<8) /* Bit 8: Rx inv Pause Frame Ov */ -#define XMR_MCTRL_OV (1L<<7) /* Bit 7: Rx MAC Ctrl-F Cnt Ov */ -#define XMR_MPAUSE_OV (1L<<6) /* Bit 6: Rx Pause MAC Ctrl-F Ov*/ -#define XMR_UC_OK_OV (1L<<5) /* Bit 5: Rx Unicast Frame CntOv*/ -#define XMR_MC_OK_OV (1L<<4) /* Bit 4: Rx Multicast Cnt Ov */ -#define XMR_BC_OK_OV (1L<<3) /* Bit 3: Rx Broadcast Cnt Ov */ -#define XMR_OK_LO_OV (1L<<2) /* Bit 2: Octets Rx OK Low CntOv*/ -#define XMR_OK_HI_OV (1L<<1) /* Bit 1: Octets Rx OK Hi Cnt Ov*/ -#define XMR_OK_OV (1L<<0) /* Bit 0: Frames Received Ok Ov */ - -#define XMR_DEF_MSK (XMR_OK_LO_OV | XMR_OK_HI_OV) - -/* XM_TX_CNT_EV 32 bit r/o Tx Counter Event Register */ -/* XM_TX_EV_MSK 32 bit r/w Tx Counter Event Mask */ - /* Bit 31..26: reserved */ -#define XMT_MAX_SZ_OV (1L<<25) /* Bit 25: 1024-MaxSize Tx Cnt Ov*/ -#define XMT_1023B_OV (1L<<24) /* Bit 24: 512-1023Byte Tx Cnt Ov*/ -#define XMT_511B_OV (1L<<23) /* Bit 23: 256-511 Byte Tx Cnt Ov*/ -#define XMT_255B_OV (1L<<22) /* Bit 22: 128-255 Byte Tx Cnt Ov*/ -#define XMT_127B_OV (1L<<21) /* Bit 21: 65-127 Byte Tx Cnt Ov */ -#define XMT_64B_OV (1L<<20) /* Bit 20: 64 Byte Tx Cnt Ov */ -#define XMT_UTIL_OV (1L<<19) /* Bit 19: Tx Util Cnt Overflow */ -#define XMT_UTIL_UR (1L<<18) /* Bit 18: Tx Util Cnt Underrun */ -#define XMT_CS_ERR_OV (1L<<17) /* Bit 17: Tx Carr Sen Err Cnt Ov*/ -#define XMT_FIFO_UR_OV (1L<<16) /* Bit 16: Tx FIFO Ur Ev Cnt Ov */ -#define XMT_EX_DEF_OV (1L<<15) /* Bit 15: Tx Ex Deferall Cnt Ov */ -#define XMT_DEF (1L<<14) /* Bit 14: Tx Deferred Cnt Ov */ -#define XMT_LAT_COL_OV (1L<<13) /* Bit 13: Tx Late Col Cnt Ov */ -#define XMT_ABO_COL_OV (1L<<12) /* Bit 12: Tx abo dueto Ex Col Ov*/ -#define XMT_MUL_COL_OV (1L<<11) /* Bit 11: Tx Mult Col Cnt Ov */ -#define XMT_SNG_COL (1L<<10) /* Bit 10: Tx Single Col Cnt Ov */ -#define XMT_MCTRL_OV (1L<<9) /* Bit 9: Tx MAC Ctrl Counter Ov*/ -#define XMT_MPAUSE (1L<<8) /* Bit 8: Tx Pause MAC Ctrl-F Ov*/ -#define XMT_BURST (1L<<7) /* Bit 7: Tx Burst Event Cnt Ov */ -#define XMT_LONG (1L<<6) /* Bit 6: Tx Long Frame Cnt Ov */ -#define XMT_UC_OK_OV (1L<<5) /* Bit 5: Tx Unicast Cnt Ov */ -#define XMT_MC_OK_OV (1L<<4) /* Bit 4: Tx Multicast Cnt Ov */ -#define XMT_BC_OK_OV (1L<<3) /* Bit 3: Tx Broadcast Cnt Ov */ -#define XMT_OK_LO_OV (1L<<2) /* Bit 2: Octets Tx OK Low CntOv*/ -#define XMT_OK_HI_OV (1L<<1) /* Bit 1: Octets Tx OK Hi Cnt Ov*/ -#define XMT_OK_OV (1L<<0) /* Bit 0: Frames Tx Ok Ov */ - -#define XMT_DEF_MSK (XMT_OK_LO_OV | XMT_OK_HI_OV) - -/* - * Receive Frame Status Encoding - */ -#define XMR_FS_LEN (0x3fffUL<<18) /* Bit 31..18: Rx Frame Length */ -#define XMR_FS_2L_VLAN (1L<<17) /* Bit 17: tagged wh 2Lev VLAN ID*/ -#define XMR_FS_1L_VLAN (1L<<16) /* Bit 16: tagged wh 1Lev VLAN ID*/ -#define XMR_FS_BC (1L<<15) /* Bit 15: Broadcast Frame */ -#define XMR_FS_MC (1L<<14) /* Bit 14: Multicast Frame */ -#define XMR_FS_UC (1L<<13) /* Bit 13: Unicast Frame */ - /* Bit 12: reserved */ -#define XMR_FS_BURST (1L<<11) /* Bit 11: Burst Mode */ -#define XMR_FS_CEX_ERR (1L<<10) /* Bit 10: Carrier Ext. Error */ -#define XMR_FS_802_3 (1L<<9) /* Bit 9: 802.3 Frame */ -#define XMR_FS_COL_ERR (1L<<8) /* Bit 8: Collision Error */ -#define XMR_FS_CAR_ERR (1L<<7) /* Bit 7: Carrier Event Error */ -#define XMR_FS_LEN_ERR (1L<<6) /* Bit 6: In-Range Length Error */ -#define XMR_FS_FRA_ERR (1L<<5) /* Bit 5: Framing Error */ -#define XMR_FS_RUNT (1L<<4) /* Bit 4: Runt Frame */ -#define XMR_FS_LNG_ERR (1L<<3) /* Bit 3: Giant (Jumbo) Frame */ -#define XMR_FS_FCS_ERR (1L<<2) /* Bit 2: Frame Check Sequ Err */ -#define XMR_FS_ERR (1L<<1) /* Bit 1: Frame Error */ -#define XMR_FS_MCTRL (1L<<0) /* Bit 0: MAC Control Packet */ - -/* - * XMR_FS_ERR will be set if - * XMR_FS_FCS_ERR, XMR_FS_LNG_ERR, XMR_FS_RUNT, - * XMR_FS_FRA_ERR, XMR_FS_LEN_ERR, or XMR_FS_CEX_ERR - * is set. XMR_FS_LNG_ERR and XMR_FS_LEN_ERR will issue - * XMR_FS_ERR unless the corresponding bit in the Receive Command - * Register is set. - */ -#define XMR_FS_ANY_ERR XMR_FS_ERR - -/*----------------------------------------------------------------------------*/ -/* - * XMAC-PHY Registers, indirect addressed over the XMAC - */ -#define PHY_XMAC_CTRL 0x00 /* 16 bit r/w PHY Control Register */ -#define PHY_XMAC_STAT 0x01 /* 16 bit r/w PHY Status Register */ -#define PHY_XMAC_ID0 0x02 /* 16 bit r/o PHY ID0 Register */ -#define PHY_XMAC_ID1 0x03 /* 16 bit r/o PHY ID1 Register */ -#define PHY_XMAC_AUNE_ADV 0x04 /* 16 bit r/w Auto-Neg. Advertisement */ -#define PHY_XMAC_AUNE_LP 0x05 /* 16 bit r/o Link Partner Abi Reg */ -#define PHY_XMAC_AUNE_EXP 0x06 /* 16 bit r/o Auto-Neg. Expansion Reg */ -#define PHY_XMAC_NEPG 0x07 /* 16 bit r/w Next Page Register */ -#define PHY_XMAC_NEPG_LP 0x08 /* 16 bit r/o Next Page Link Partner */ - /* 0x09 - 0x0e: reserved */ -#define PHY_XMAC_EXT_STAT 0x0f /* 16 bit r/o Ext Status Register */ -#define PHY_XMAC_RES_ABI 0x10 /* 16 bit r/o PHY Resolved Ability */ - -/*----------------------------------------------------------------------------*/ -/* - * Broadcom-PHY Registers, indirect addressed over XMAC - */ -#define PHY_BCOM_CTRL 0x00 /* 16 bit r/w PHY Control Register */ -#define PHY_BCOM_STAT 0x01 /* 16 bit r/o PHY Status Register */ -#define PHY_BCOM_ID0 0x02 /* 16 bit r/o PHY ID0 Register */ -#define PHY_BCOM_ID1 0x03 /* 16 bit r/o PHY ID1 Register */ -#define PHY_BCOM_AUNE_ADV 0x04 /* 16 bit r/w Auto-Neg. Advertisement */ -#define PHY_BCOM_AUNE_LP 0x05 /* 16 bit r/o Link Part Ability Reg */ -#define PHY_BCOM_AUNE_EXP 0x06 /* 16 bit r/o Auto-Neg. Expansion Reg */ -#define PHY_BCOM_NEPG 0x07 /* 16 bit r/w Next Page Register */ -#define PHY_BCOM_NEPG_LP 0x08 /* 16 bit r/o Next Page Link Partner */ - /* Broadcom-specific registers */ -#define PHY_BCOM_1000T_CTRL 0x09 /* 16 bit r/w 1000Base-T Ctrl Reg */ -#define PHY_BCOM_1000T_STAT 0x0a /* 16 bit r/o 1000Base-T Status Reg */ - /* 0x0b - 0x0e: reserved */ -#define PHY_BCOM_EXT_STAT 0x0f /* 16 bit r/o Extended Status Reg */ -#define PHY_BCOM_P_EXT_CTRL 0x10 /* 16 bit r/w PHY Extended Ctrl Reg */ -#define PHY_BCOM_P_EXT_STAT 0x11 /* 16 bit r/o PHY Extended Stat Reg */ -#define PHY_BCOM_RE_CTR 0x12 /* 16 bit r/w Receive Error Counter */ -#define PHY_BCOM_FC_CTR 0x13 /* 16 bit r/w False Carrier Sense Cnt */ -#define PHY_BCOM_RNO_CTR 0x14 /* 16 bit r/w Receiver NOT_OK Cnt */ - /* 0x15 - 0x17: reserved */ -#define PHY_BCOM_AUX_CTRL 0x18 /* 16 bit r/w Auxiliary Control Reg */ -#define PHY_BCOM_AUX_STAT 0x19 /* 16 bit r/o Auxiliary Stat Summary */ -#define PHY_BCOM_INT_STAT 0x1a /* 16 bit r/o Interrupt Status Reg */ -#define PHY_BCOM_INT_MASK 0x1b /* 16 bit r/w Interrupt Mask Reg */ - /* 0x1c: reserved */ - /* 0x1d - 0x1f: test registers */ - -/*----------------------------------------------------------------------------*/ -/* - * Marvel-PHY Registers, indirect addressed over GMAC - */ -#define PHY_MARV_CTRL 0x00 /* 16 bit r/w PHY Control Register */ -#define PHY_MARV_STAT 0x01 /* 16 bit r/o PHY Status Register */ -#define PHY_MARV_ID0 0x02 /* 16 bit r/o PHY ID0 Register */ -#define PHY_MARV_ID1 0x03 /* 16 bit r/o PHY ID1 Register */ -#define PHY_MARV_AUNE_ADV 0x04 /* 16 bit r/w Auto-Neg. Advertisement */ -#define PHY_MARV_AUNE_LP 0x05 /* 16 bit r/o Link Part Ability Reg */ -#define PHY_MARV_AUNE_EXP 0x06 /* 16 bit r/o Auto-Neg. Expansion Reg */ -#define PHY_MARV_NEPG 0x07 /* 16 bit r/w Next Page Register */ -#define PHY_MARV_NEPG_LP 0x08 /* 16 bit r/o Next Page Link Partner */ - /* Marvel-specific registers */ -#define PHY_MARV_1000T_CTRL 0x09 /* 16 bit r/w 1000Base-T Ctrl Reg */ -#define PHY_MARV_1000T_STAT 0x0a /* 16 bit r/o 1000Base-T Status Reg */ - /* 0x0b - 0x0e: reserved */ -#define PHY_MARV_EXT_STAT 0x0f /* 16 bit r/o Extended Status Reg */ -#define PHY_MARV_PHY_CTRL 0x10 /* 16 bit r/w PHY Specific Ctrl Reg */ -#define PHY_MARV_PHY_STAT 0x11 /* 16 bit r/o PHY Specific Stat Reg */ -#define PHY_MARV_INT_MASK 0x12 /* 16 bit r/w Interrupt Mask Reg */ -#define PHY_MARV_INT_STAT 0x13 /* 16 bit r/o Interrupt Status Reg */ -#define PHY_MARV_EXT_CTRL 0x14 /* 16 bit r/w Ext. PHY Specific Ctrl */ -#define PHY_MARV_RXE_CNT 0x15 /* 16 bit r/w Receive Error Counter */ -#define PHY_MARV_EXT_ADR 0x16 /* 16 bit r/w Ext. Ad. for Cable Diag. */ - /* 0x17: reserved */ -#define PHY_MARV_LED_CTRL 0x18 /* 16 bit r/w LED Control Reg */ -#define PHY_MARV_LED_OVER 0x19 /* 16 bit r/w Manual LED Override Reg */ -#define PHY_MARV_EXT_CTRL_2 0x1a /* 16 bit r/w Ext. PHY Specific Ctrl 2 */ -#define PHY_MARV_EXT_P_STAT 0x1b /* 16 bit r/w Ext. PHY Spec. Stat Reg */ -#define PHY_MARV_CABLE_DIAG 0x1c /* 16 bit r/o Cable Diagnostic Reg */ - /* 0x1d - 0x1f: reserved */ - -/*----------------------------------------------------------------------------*/ -/* - * Level One-PHY Registers, indirect addressed over XMAC - */ -#define PHY_LONE_CTRL 0x00 /* 16 bit r/w PHY Control Register */ -#define PHY_LONE_STAT 0x01 /* 16 bit r/o PHY Status Register */ -#define PHY_LONE_ID0 0x02 /* 16 bit r/o PHY ID0 Register */ -#define PHY_LONE_ID1 0x03 /* 16 bit r/o PHY ID1 Register */ -#define PHY_LONE_AUNE_ADV 0x04 /* 16 bit r/w Auto-Neg. Advertisement */ -#define PHY_LONE_AUNE_LP 0x05 /* 16 bit r/o Link Part Ability Reg */ -#define PHY_LONE_AUNE_EXP 0x06 /* 16 bit r/o Auto-Neg. Expansion Reg */ -#define PHY_LONE_NEPG 0x07 /* 16 bit r/w Next Page Register */ -#define PHY_LONE_NEPG_LP 0x08 /* 16 bit r/o Next Page Link Partner */ - /* Level One-specific registers */ -#define PHY_LONE_1000T_CTRL 0x09 /* 16 bit r/w 1000Base-T Control Reg*/ -#define PHY_LONE_1000T_STAT 0x0a /* 16 bit r/o 1000Base-T Status Reg */ - /* 0x0b -0x0e: reserved */ -#define PHY_LONE_EXT_STAT 0x0f /* 16 bit r/o Extended Status Reg */ -#define PHY_LONE_PORT_CFG 0x10 /* 16 bit r/w Port Configuration Reg*/ -#define PHY_LONE_Q_STAT 0x11 /* 16 bit r/o Quick Status Reg */ -#define PHY_LONE_INT_ENAB 0x12 /* 16 bit r/w Interrupt Enable Reg */ -#define PHY_LONE_INT_STAT 0x13 /* 16 bit r/o Interrupt Status Reg */ -#define PHY_LONE_LED_CFG 0x14 /* 16 bit r/w LED Configuration Reg */ -#define PHY_LONE_PORT_CTRL 0x15 /* 16 bit r/w Port Control Reg */ -#define PHY_LONE_CIM 0x16 /* 16 bit r/o CIM Reg */ - /* 0x17 -0x1c: reserved */ - -/*----------------------------------------------------------------------------*/ -/* - * National-PHY Registers, indirect addressed over XMAC - */ -#define PHY_NAT_CTRL 0x00 /* 16 bit r/w PHY Control Register */ -#define PHY_NAT_STAT 0x01 /* 16 bit r/w PHY Status Register */ -#define PHY_NAT_ID0 0x02 /* 16 bit r/o PHY ID0 Register */ -#define PHY_NAT_ID1 0x03 /* 16 bit r/o PHY ID1 Register */ -#define PHY_NAT_AUNE_ADV 0x04 /* 16 bit r/w Auto-Neg. Advertisement */ -#define PHY_NAT_AUNE_LP 0x05 /* 16 bit r/o Link Partner Ability Reg */ -#define PHY_NAT_AUNE_EXP 0x06 /* 16 bit r/o Auto-Neg. Expansion Reg */ -#define PHY_NAT_NEPG 0x07 /* 16 bit r/w Next Page Register */ -#define PHY_NAT_NEPG_LP 0x08 /* 16 bit r/o Next Page Link Partner Reg */ - /* National-specific registers */ -#define PHY_NAT_1000T_CTRL 0x09 /* 16 bit r/w 1000Base-T Control Reg */ -#define PHY_NAT_1000T_STAT 0x0a /* 16 bit r/o 1000Base-T Status Reg */ - /* 0x0b -0x0e: reserved */ -#define PHY_NAT_EXT_STAT 0x0f /* 16 bit r/o Extended Status Register */ -#define PHY_NAT_EXT_CTRL1 0x10 /* 16 bit r/o Extended Control Reg1 */ -#define PHY_NAT_Q_STAT1 0x11 /* 16 bit r/o Quick Status Reg1 */ -#define PHY_NAT_10B_OP 0x12 /* 16 bit r/o 10Base-T Operations Reg */ -#define PHY_NAT_EXT_CTRL2 0x13 /* 16 bit r/o Extended Control Reg1 */ -#define PHY_NAT_Q_STAT2 0x14 /* 16 bit r/o Quick Status Reg2 */ - /* 0x15 -0x18: reserved */ -#define PHY_NAT_PHY_ADDR 0x19 /* 16 bit r/o PHY Address Register */ - - -/*----------------------------------------------------------------------------*/ - -/* - * PHY bit definitions - * Bits defined as PHY_X_..., PHY_B_..., PHY_L_... or PHY_N_... are - * XMAC/Broadcom/LevelOne/National/Marvell-specific. - * All other are general. - */ - -/***** PHY_XMAC_CTRL 16 bit r/w PHY Control Register *****/ -/***** PHY_BCOM_CTRL 16 bit r/w PHY Control Register *****/ -/***** PHY_MARV_CTRL 16 bit r/w PHY Status Register *****/ -/***** PHY_LONE_CTRL 16 bit r/w PHY Control Register *****/ -#define PHY_CT_RESET (1<<15) /* Bit 15: (sc) clear all PHY related regs */ -#define PHY_CT_LOOP (1<<14) /* Bit 14: enable Loopback over PHY */ -#define PHY_CT_SPS_LSB (1<<13) /* Bit 13: (BC,L1) Speed select, lower bit */ -#define PHY_CT_ANE (1<<12) /* Bit 12: Auto-Negotiation Enabled */ -#define PHY_CT_PDOWN (1<<11) /* Bit 11: (BC,L1) Power Down Mode */ -#define PHY_CT_ISOL (1<<10) /* Bit 10: (BC,L1) Isolate Mode */ -#define PHY_CT_RE_CFG (1<<9) /* Bit 9: (sc) Restart Auto-Negotiation */ -#define PHY_CT_DUP_MD (1<<8) /* Bit 8: Duplex Mode */ -#define PHY_CT_COL_TST (1<<7) /* Bit 7: (BC,L1) Collision Test enabled */ -#define PHY_CT_SPS_MSB (1<<6) /* Bit 6: (BC,L1) Speed select, upper bit */ - /* Bit 5..0: reserved */ - -#define PHY_CT_SP1000 PHY_CT_SPS_MSB /* enable speed of 1000 Mbps */ -#define PHY_CT_SP100 PHY_CT_SPS_LSB /* enable speed of 100 Mbps */ -#define PHY_CT_SP10 (0) /* enable speed of 10 Mbps */ - - -/***** PHY_XMAC_STAT 16 bit r/w PHY Status Register *****/ -/***** PHY_BCOM_STAT 16 bit r/w PHY Status Register *****/ -/***** PHY_MARV_STAT 16 bit r/w PHY Status Register *****/ -/***** PHY_LONE_STAT 16 bit r/w PHY Status Register *****/ - /* Bit 15..9: reserved */ - /* (BC/L1) 100/10 Mbps cap bits ignored*/ -#define PHY_ST_EXT_ST (1<<8) /* Bit 8: Extended Status Present */ - /* Bit 7: reserved */ -#define PHY_ST_PRE_SUP (1<<6) /* Bit 6: (BC/L1) preamble suppression */ -#define PHY_ST_AN_OVER (1<<5) /* Bit 5: Auto-Negotiation Over */ -#define PHY_ST_REM_FLT (1<<4) /* Bit 4: Remote Fault Condition Occured */ -#define PHY_ST_AN_CAP (1<<3) /* Bit 3: Auto-Negotiation Capability */ -#define PHY_ST_LSYNC (1<<2) /* Bit 2: Link Synchronized */ -#define PHY_ST_JAB_DET (1<<1) /* Bit 1: (BC/L1) Jabber Detected */ -#define PHY_ST_EXT_REG (1<<0) /* Bit 0: Extended Register available */ - - -/***** PHY_XMAC_ID1 16 bit r/o PHY ID1 Register */ -/***** PHY_BCOM_ID1 16 bit r/o PHY ID1 Register */ -/***** PHY_MARV_ID1 16 bit r/o PHY ID1 Register */ -/***** PHY_LONE_ID1 16 bit r/o PHY ID1 Register */ -#define PHY_I1_OUI_MSK (0x3f<<10) /* Bit 15..10: Organization Unique ID */ -#define PHY_I1_MOD_NUM (0x3f<<4) /* Bit 9.. 4: Model Number */ -#define PHY_I1_REV_MSK 0x0f /* Bit 3.. 0: Revision Number */ - -/* different Broadcom PHY Ids */ -#define PHY_BCOM_ID1_A1 0x6041 -#define PHY_BCOM_ID1_B2 0x6043 -#define PHY_BCOM_ID1_C0 0x6044 -#define PHY_BCOM_ID1_C5 0x6047 - - -/***** PHY_XMAC_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/ -/***** PHY_XMAC_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/ -#define PHY_AN_NXT_PG (1<<15) /* Bit 15: Request Next Page */ -#define PHY_X_AN_ACK (1<<14) /* Bit 14: (ro) Acknowledge Received */ -#define PHY_X_AN_RFB (3<<12) /* Bit 13..12: Remote Fault Bits */ - /* Bit 11.. 9: reserved */ -#define PHY_X_AN_PAUSE (3<<7) /* Bit 8.. 7: Pause Bits */ -#define PHY_X_AN_HD (1<<6) /* Bit 6: Half Duplex */ -#define PHY_X_AN_FD (1<<5) /* Bit 5: Full Duplex */ - /* Bit 4.. 0: reserved */ - -/***** PHY_BCOM_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/ -/***** PHY_BCOM_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/ -/* PHY_AN_NXT_PG (see XMAC) Bit 15: Request Next Page */ - /* Bit 14: reserved */ -#define PHY_B_AN_RF (1<<13) /* Bit 13: Remote Fault */ - /* Bit 12: reserved */ -#define PHY_B_AN_ASP (1<<11) /* Bit 11: Asymmetric Pause */ -#define PHY_B_AN_PC (1<<10) /* Bit 10: Pause Capable */ - /* Bit 9..5: 100/10 BT cap bits ingnored */ -#define PHY_B_AN_SEL 0x1f /* Bit 4..0: Selector Field, 00001=Ethernet*/ - -/***** PHY_LONE_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/ -/***** PHY_LONE_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/ -/* PHY_AN_NXT_PG (see XMAC) Bit 15: Request Next Page */ - /* Bit 14: reserved */ -#define PHY_L_AN_RF (1<<13) /* Bit 13: Remote Fault */ - /* Bit 12: reserved */ -#define PHY_L_AN_ASP (1<<11) /* Bit 11: Asymmetric Pause */ -#define PHY_L_AN_PC (1<<10) /* Bit 10: Pause Capable */ - /* Bit 9..5: 100/10 BT cap bits ingnored */ -#define PHY_L_AN_SEL 0x1f /* Bit 4..0: Selector Field, 00001=Ethernet*/ - -/***** PHY_NAT_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/ -/***** PHY_NAT_AUNE_LP 16 bit r/o Link Partner Ability Reg *****/ -/* PHY_AN_NXT_PG (see XMAC) Bit 15: Request Next Page */ - /* Bit 14: reserved */ -#define PHY_N_AN_RF (1<<13) /* Bit 13: Remote Fault */ - /* Bit 12: reserved */ -#define PHY_N_AN_100F (1<<11) /* Bit 11: 100Base-T2 FD Support */ -#define PHY_N_AN_100H (1<<10) /* Bit 10: 100Base-T2 HD Support */ - /* Bit 9..5: 100/10 BT cap bits ingnored */ -#define PHY_N_AN_SEL 0x1f /* Bit 4..0: Selector Field, 00001=Ethernet*/ - -/* field type definition for PHY_x_AN_SEL */ -#define PHY_SEL_TYPE 0x01 /* 00001 = Ethernet */ - -/***** PHY_XMAC_AUNE_EXP 16 bit r/o Auto-Negotiation Expansion Reg *****/ - /* Bit 15..4: reserved */ -#define PHY_ANE_LP_NP (1<<3) /* Bit 3: Link Partner can Next Page */ -#define PHY_ANE_LOC_NP (1<<2) /* Bit 2: Local PHY can Next Page */ -#define PHY_ANE_RX_PG (1<<1) /* Bit 1: Page Received */ - /* Bit 0: reserved */ - -/***** PHY_BCOM_AUNE_EXP 16 bit r/o Auto-Negotiation Expansion Reg *****/ -/***** PHY_LONE_AUNE_EXP 16 bit r/o Auto-Negotiation Expansion Reg *****/ -/***** PHY_MARV_AUNE_EXP 16 bit r/o Auto-Negotiation Expansion Reg *****/ - /* Bit 15..5: reserved */ -#define PHY_ANE_PAR_DF (1<<4) /* Bit 4: Parallel Detection Fault */ -/* PHY_ANE_LP_NP (see XMAC) Bit 3: Link Partner can Next Page */ -/* PHY_ANE_LOC_NP (see XMAC) Bit 2: Local PHY can Next Page */ -/* PHY_ANE_RX_PG (see XMAC) Bit 1: Page Received */ -#define PHY_ANE_LP_CAP (1<<0) /* Bit 0: Link Partner Auto-Neg. Cap. */ - -/***** PHY_XMAC_NEPG 16 bit r/w Next Page Register *****/ -/***** PHY_BCOM_NEPG 16 bit r/w Next Page Register *****/ -/***** PHY_LONE_NEPG 16 bit r/w Next Page Register *****/ -/***** PHY_XMAC_NEPG_LP 16 bit r/o Next Page Link Partner *****/ -/***** PHY_BCOM_NEPG_LP 16 bit r/o Next Page Link Partner *****/ -/***** PHY_LONE_NEPG_LP 16 bit r/o Next Page Link Partner *****/ -#define PHY_NP_MORE (1<<15) /* Bit 15: More, Next Pages to follow */ -#define PHY_NP_ACK1 (1<<14) /* Bit 14: (ro) Ack1, for receiving a message */ -#define PHY_NP_MSG_VAL (1<<13) /* Bit 13: Message Page valid */ -#define PHY_NP_ACK2 (1<<12) /* Bit 12: Ack2, comply with msg content */ -#define PHY_NP_TOG (1<<11) /* Bit 11: Toggle Bit, ensure sync */ -#define PHY_NP_MSG 0x07ff /* Bit 10..0: Message from/to Link Partner */ - -/* - * XMAC-Specific - */ -/***** PHY_XMAC_EXT_STAT 16 bit r/w Extended Status Register *****/ -#define PHY_X_EX_FD (1<<15) /* Bit 15: Device Supports Full Duplex */ -#define PHY_X_EX_HD (1<<14) /* Bit 14: Device Supports Half Duplex */ - /* Bit 13..0: reserved */ - -/***** PHY_XMAC_RES_ABI 16 bit r/o PHY Resolved Ability *****/ - /* Bit 15..9: reserved */ -#define PHY_X_RS_PAUSE (3<<7) /* Bit 8..7: selected Pause Mode */ -#define PHY_X_RS_HD (1<<6) /* Bit 6: Half Duplex Mode selected */ -#define PHY_X_RS_FD (1<<5) /* Bit 5: Full Duplex Mode selected */ -#define PHY_X_RS_ABLMIS (1<<4) /* Bit 4: duplex or pause cap mismatch */ -#define PHY_X_RS_PAUMIS (1<<3) /* Bit 3: pause capability mismatch */ - /* Bit 2..0: reserved */ -/* - * Remote Fault Bits (PHY_X_AN_RFB) encoding - */ -#define X_RFB_OK (0<<12) /* Bit 13..12 No errors, Link OK */ -#define X_RFB_LF (1<<12) /* Bit 13..12 Link Failure */ -#define X_RFB_OFF (2<<12) /* Bit 13..12 Offline */ -#define X_RFB_AN_ERR (3<<12) /* Bit 13..12 Auto-Negotiation Error */ - -/* - * Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding - */ -#define PHY_X_P_NO_PAUSE (0<<7) /* Bit 8..7: no Pause Mode */ -#define PHY_X_P_SYM_MD (1<<7) /* Bit 8..7: symmetric Pause Mode */ -#define PHY_X_P_ASYM_MD (2<<7) /* Bit 8..7: asymmetric Pause Mode */ -#define PHY_X_P_BOTH_MD (3<<7) /* Bit 8..7: both Pause Mode */ - - -/* - * Broadcom-Specific - */ -/***** PHY_BCOM_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/ -#define PHY_B_1000C_TEST (7<<13) /* Bit 15..13: Test Modes */ -#define PHY_B_1000C_MSE (1<<12) /* Bit 12: Master/Slave Enable */ -#define PHY_B_1000C_MSC (1<<11) /* Bit 11: M/S Configuration */ -#define PHY_B_1000C_RD (1<<10) /* Bit 10: Repeater/DTE */ -#define PHY_B_1000C_AFD (1<<9) /* Bit 9: Advertise Full Duplex */ -#define PHY_B_1000C_AHD (1<<8) /* Bit 8: Advertise Half Duplex */ - /* Bit 7..0: reserved */ - -/***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/ -/***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/ -#define PHY_B_1000S_MSF (1<<15) /* Bit 15: Master/Slave Fault */ -#define PHY_B_1000S_MSR (1<<14) /* Bit 14: Master/Slave Result */ -#define PHY_B_1000S_LRS (1<<13) /* Bit 13: Local Receiver Status */ -#define PHY_B_1000S_RRS (1<<12) /* Bit 12: Remote Receiver Status */ -#define PHY_B_1000S_LP_FD (1<<11) /* Bit 11: Link Partner can FD */ -#define PHY_B_1000S_LP_HD (1<<10) /* Bit 10: Link Partner can HD */ - /* Bit 9..8: reserved */ -#define PHY_B_1000S_IEC 0xff /* Bit 7..0: Idle Error Count */ - -/***** PHY_BCOM_EXT_STAT 16 bit r/o Extended Status Register *****/ -#define PHY_B_ES_X_FD_CAP (1<<15) /* Bit 15: 1000Base-X FD capable */ -#define PHY_B_ES_X_HD_CAP (1<<14) /* Bit 14: 1000Base-X HD capable */ -#define PHY_B_ES_T_FD_CAP (1<<13) /* Bit 13: 1000Base-T FD capable */ -#define PHY_B_ES_T_HD_CAP (1<<12) /* Bit 12: 1000Base-T HD capable */ - /* Bit 11..0: reserved */ - -/***** PHY_BCOM_P_EXT_CTRL 16 bit r/w PHY Extended Control Reg *****/ -#define PHY_B_PEC_MAC_PHY (1<<15) /* Bit 15: 10BIT/GMI-Interface */ -#define PHY_B_PEC_DIS_CROSS (1<<14) /* Bit 14: Disable MDI Crossover */ -#define PHY_B_PEC_TX_DIS (1<<13) /* Bit 13: Tx output Disabled */ -#define PHY_B_PEC_INT_DIS (1<<12) /* Bit 12: Interrupts Disabled */ -#define PHY_B_PEC_F_INT (1<<11) /* Bit 11: Force Interrupt */ -#define PHY_B_PEC_BY_45 (1<<10) /* Bit 10: Bypass 4B5B-Decoder */ -#define PHY_B_PEC_BY_SCR (1<<9) /* Bit 9: Bypass Scrambler */ -#define PHY_B_PEC_BY_MLT3 (1<<8) /* Bit 8: Bypass MLT3 Encoder */ -#define PHY_B_PEC_BY_RXA (1<<7) /* Bit 7: Bypass Rx Alignm. */ -#define PHY_B_PEC_RES_SCR (1<<6) /* Bit 6: Reset Scrambler */ -#define PHY_B_PEC_EN_LTR (1<<5) /* Bit 5: Ena LED Traffic Mode */ -#define PHY_B_PEC_LED_ON (1<<4) /* Bit 4: Force LED's on */ -#define PHY_B_PEC_LED_OFF (1<<3) /* Bit 3: Force LED's off */ -#define PHY_B_PEC_EX_IPG (1<<2) /* Bit 2: Extend Tx IPG Mode */ -#define PHY_B_PEC_3_LED (1<<1) /* Bit 1: Three Link LED mode */ -#define PHY_B_PEC_HIGH_LA (1<<0) /* Bit 0: GMII FIFO Elasticy */ - -/***** PHY_BCOM_P_EXT_STAT 16 bit r/o PHY Extended Status Reg *****/ - /* Bit 15..14: reserved */ -#define PHY_B_PES_CROSS_STAT (1<<13) /* Bit 13: MDI Crossover Status */ -#define PHY_B_PES_INT_STAT (1<<12) /* Bit 12: Interrupt Status */ -#define PHY_B_PES_RRS (1<<11) /* Bit 11: Remote Receiver Stat. */ -#define PHY_B_PES_LRS (1<<10) /* Bit 10: Local Receiver Stat. */ -#define PHY_B_PES_LOCKED (1<<9) /* Bit 9: Locked */ -#define PHY_B_PES_LS (1<<8) /* Bit 8: Link Status */ -#define PHY_B_PES_RF (1<<7) /* Bit 7: Remote Fault */ -#define PHY_B_PES_CE_ER (1<<6) /* Bit 6: Carrier Ext Error */ -#define PHY_B_PES_BAD_SSD (1<<5) /* Bit 5: Bad SSD */ -#define PHY_B_PES_BAD_ESD (1<<4) /* Bit 4: Bad ESD */ -#define PHY_B_PES_RX_ER (1<<3) /* Bit 3: Receive Error */ -#define PHY_B_PES_TX_ER (1<<2) /* Bit 2: Transmit Error */ -#define PHY_B_PES_LOCK_ER (1<<1) /* Bit 1: Lock Error */ -#define PHY_B_PES_MLT3_ER (1<<0) /* Bit 0: MLT3 code Error */ - -/***** PHY_BCOM_FC_CTR 16 bit r/w False Carrier Counter *****/ - /* Bit 15..8: reserved */ -#define PHY_B_FC_CTR 0xff /* Bit 7..0: False Carrier Counter */ - -/***** PHY_BCOM_RNO_CTR 16 bit r/w Receive NOT_OK Counter *****/ -#define PHY_B_RC_LOC_MSK 0xff00 /* Bit 15..8: Local Rx NOT_OK cnt */ -#define PHY_B_RC_REM_MSK 0x00ff /* Bit 7..0: Remote Rx NOT_OK cnt */ - -/***** PHY_BCOM_AUX_CTRL 16 bit r/w Auxiliary Control Reg *****/ -#define PHY_B_AC_L_SQE (1<<15) /* Bit 15: Low Squelch */ -#define PHY_B_AC_LONG_PACK (1<<14) /* Bit 14: Rx Long Packets */ -#define PHY_B_AC_ER_CTRL (3<<12) /* Bit 13..12: Edgerate Control */ - /* Bit 11: reserved */ -#define PHY_B_AC_TX_TST (1<<10) /* Bit 10: Tx test bit, always 1 */ - /* Bit 9.. 8: reserved */ -#define PHY_B_AC_DIS_PRF (1<<7) /* Bit 7: dis part resp filter */ - /* Bit 6: reserved */ -#define PHY_B_AC_DIS_PM (1<<5) /* Bit 5: dis power management */ - /* Bit 4: reserved */ -#define PHY_B_AC_DIAG (1<<3) /* Bit 3: Diagnostic Mode */ - /* Bit 2.. 0: reserved */ - -/***** PHY_BCOM_AUX_STAT 16 bit r/o Auxiliary Status Reg *****/ -#define PHY_B_AS_AN_C (1<<15) /* Bit 15: AutoNeg complete */ -#define PHY_B_AS_AN_CA (1<<14) /* Bit 14: AN Complete Ack */ -#define PHY_B_AS_ANACK_D (1<<13) /* Bit 13: AN Ack Detect */ -#define PHY_B_AS_ANAB_D (1<<12) /* Bit 12: AN Ability Detect */ -#define PHY_B_AS_NPW (1<<11) /* Bit 11: AN Next Page Wait */ -#define PHY_B_AS_AN_RES_MSK (7<<8) /* Bit 10..8: AN HDC */ -#define PHY_B_AS_PDF (1<<7) /* Bit 7: Parallel Detect. Fault */ -#define PHY_B_AS_RF (1<<6) /* Bit 6: Remote Fault */ -#define PHY_B_AS_ANP_R (1<<5) /* Bit 5: AN Page Received */ -#define PHY_B_AS_LP_ANAB (1<<4) /* Bit 4: LP AN Ability */ -#define PHY_B_AS_LP_NPAB (1<<3) /* Bit 3: LP Next Page Ability */ -#define PHY_B_AS_LS (1<<2) /* Bit 2: Link Status */ -#define PHY_B_AS_PRR (1<<1) /* Bit 1: Pause Resolution-Rx */ -#define PHY_B_AS_PRT (1<<0) /* Bit 0: Pause Resolution-Tx */ - -#define PHY_B_AS_PAUSE_MSK (PHY_B_AS_PRR | PHY_B_AS_PRT) - -/***** PHY_BCOM_INT_STAT 16 bit r/o Interrupt Status Reg *****/ -/***** PHY_BCOM_INT_MASK 16 bit r/w Interrupt Mask Reg *****/ - /* Bit 15: reserved */ -#define PHY_B_IS_PSE (1<<14) /* Bit 14: Pair Swap Error */ -#define PHY_B_IS_MDXI_SC (1<<13) /* Bit 13: MDIX Status Change */ -#define PHY_B_IS_HCT (1<<12) /* Bit 12: counter above 32k */ -#define PHY_B_IS_LCT (1<<11) /* Bit 11: counter above 128 */ -#define PHY_B_IS_AN_PR (1<<10) /* Bit 10: Page Received */ -#define PHY_B_IS_NO_HDCL (1<<9) /* Bit 9: No HCD Link */ -#define PHY_B_IS_NO_HDC (1<<8) /* Bit 8: No HCD */ -#define PHY_B_IS_NEG_USHDC (1<<7) /* Bit 7: Negotiated Unsup. HCD */ -#define PHY_B_IS_SCR_S_ER (1<<6) /* Bit 6: Scrambler Sync Error */ -#define PHY_B_IS_RRS_CHANGE (1<<5) /* Bit 5: Remote Rx Stat Change */ -#define PHY_B_IS_LRS_CHANGE (1<<4) /* Bit 4: Local Rx Stat Change */ -#define PHY_B_IS_DUP_CHANGE (1<<3) /* Bit 3: Duplex Mode Change */ -#define PHY_B_IS_LSP_CHANGE (1<<2) /* Bit 2: Link Speed Change */ -#define PHY_B_IS_LST_CHANGE (1<<1) /* Bit 1: Link Status Changed */ -#define PHY_B_IS_CRC_ER (1<<0) /* Bit 0: CRC Error */ - -#define PHY_B_DEF_MSK (~(PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE)) - -/* Pause Bits (PHY_B_AN_ASP and PHY_B_AN_PC) encoding */ -#define PHY_B_P_NO_PAUSE (0<<10) /* Bit 11..10: no Pause Mode */ -#define PHY_B_P_SYM_MD (1<<10) /* Bit 11..10: symmetric Pause Mode */ -#define PHY_B_P_ASYM_MD (2<<10) /* Bit 11..10: asymmetric Pause Mode */ -#define PHY_B_P_BOTH_MD (3<<10) /* Bit 11..10: both Pause Mode */ - -/* - * Resolved Duplex mode and Capabilities (Aux Status Summary Reg) - */ -#define PHY_B_RES_1000FD (7<<8) /* Bit 10..8: 1000Base-T Full Dup. */ -#define PHY_B_RES_1000HD (6<<8) /* Bit 10..8: 1000Base-T Half Dup. */ -/* others: 100/10: invalid for us */ - -/* - * Level One-Specific - */ -/***** PHY_LONE_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/ -#define PHY_L_1000C_TEST (7<<13) /* Bit 15..13: Test Modes */ -#define PHY_L_1000C_MSE (1<<12) /* Bit 12: Master/Slave Enable */ -#define PHY_L_1000C_MSC (1<<11) /* Bit 11: M/S Configuration */ -#define PHY_L_1000C_RD (1<<10) /* Bit 10: Repeater/DTE */ -#define PHY_L_1000C_AFD (1<<9) /* Bit 9: Advertise Full Duplex */ -#define PHY_L_1000C_AHD (1<<8) /* Bit 8: Advertise Half Duplex */ - /* Bit 7..0: reserved */ - -/***** PHY_LONE_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/ -#define PHY_L_1000S_MSF (1<<15) /* Bit 15: Master/Slave Fault */ -#define PHY_L_1000S_MSR (1<<14) /* Bit 14: Master/Slave Result */ -#define PHY_L_1000S_LRS (1<<13) /* Bit 13: Local Receiver Status */ -#define PHY_L_1000S_RRS (1<<12) /* Bit 12: Remote Receiver Status */ -#define PHY_L_1000S_LP_FD (1<<11) /* Bit 11: Link Partner can FD */ -#define PHY_L_1000S_LP_HD (1<<10) /* Bit 10: Link Partner can HD */ - /* Bit 9..8: reserved */ -#define PHY_B_1000S_IEC 0xff /* Bit 7..0: Idle Error Count */ - -/***** PHY_LONE_EXT_STAT 16 bit r/o Extended Status Register *****/ -#define PHY_L_ES_X_FD_CAP (1<<15) /* Bit 15: 1000Base-X FD capable */ -#define PHY_L_ES_X_HD_CAP (1<<14) /* Bit 14: 1000Base-X HD capable */ -#define PHY_L_ES_T_FD_CAP (1<<13) /* Bit 13: 1000Base-T FD capable */ -#define PHY_L_ES_T_HD_CAP (1<<12) /* Bit 12: 1000Base-T HD capable */ - /* Bit 11..0: reserved */ - -/***** PHY_LONE_PORT_CFG 16 bit r/w Port Configuration Reg *****/ -#define PHY_L_PC_REP_MODE (1<<15) /* Bit 15: Repeater Mode */ - /* Bit 14: reserved */ -#define PHY_L_PC_TX_DIS (1<<13) /* Bit 13: Tx output Disabled */ -#define PHY_L_PC_BY_SCR (1<<12) /* Bit 12: Bypass Scrambler */ -#define PHY_L_PC_BY_45 (1<<11) /* Bit 11: Bypass 4B5B-Decoder */ -#define PHY_L_PC_JAB_DIS (1<<10) /* Bit 10: Jabber Disabled */ -#define PHY_L_PC_SQE (1<<9) /* Bit 9: Enable Heartbeat */ -#define PHY_L_PC_TP_LOOP (1<<8) /* Bit 8: TP Loopback */ -#define PHY_L_PC_SSS (1<<7) /* Bit 7: Smart Speed Selection */ -#define PHY_L_PC_FIFO_SIZE (1<<6) /* Bit 6: FIFO Size */ -#define PHY_L_PC_PRE_EN (1<<5) /* Bit 5: Preamble Enable */ -#define PHY_L_PC_CIM (1<<4) /* Bit 4: Carrier Integrity Mon */ -#define PHY_L_PC_10_SER (1<<3) /* Bit 3: Use Serial Output */ -#define PHY_L_PC_ANISOL (1<<2) /* Bit 2: Unisolate Port */ -#define PHY_L_PC_TEN_BIT (1<<1) /* Bit 1: 10bit iface mode on */ -#define PHY_L_PC_ALTCLOCK (1<<0) /* Bit 0: (ro) ALTCLOCK Mode on */ - -/***** PHY_LONE_Q_STAT 16 bit r/o Quick Status Reg *****/ -#define PHY_L_QS_D_RATE (3<<14) /* Bit 15..14: Data Rate */ -#define PHY_L_QS_TX_STAT (1<<13) /* Bit 13: Transmitting */ -#define PHY_L_QS_RX_STAT (1<<12) /* Bit 12: Receiving */ -#define PHY_L_QS_COL_STAT (1<<11) /* Bit 11: Collision */ -#define PHY_L_QS_L_STAT (1<<10) /* Bit 10: Link is up */ -#define PHY_L_QS_DUP_MOD (1<<9) /* Bit 9: Full/Half Duplex */ -#define PHY_L_QS_AN (1<<8) /* Bit 8: AutoNeg is On */ -#define PHY_L_QS_AN_C (1<<7) /* Bit 7: AN is Complete */ -#define PHY_L_QS_LLE (7<<4) /* Bit 6: Line Length Estim. */ -#define PHY_L_QS_PAUSE (1<<3) /* Bit 3: LP advertised Pause */ -#define PHY_L_QS_AS_PAUSE (1<<2) /* Bit 2: LP adv. asym. Pause */ -#define PHY_L_QS_ISOLATE (1<<1) /* Bit 1: CIM Isolated */ -#define PHY_L_QS_EVENT (1<<0) /* Bit 0: Event has occurred */ - -/***** PHY_LONE_INT_ENAB 16 bit r/w Interrupt Enable Reg *****/ -/***** PHY_LONE_INT_STAT 16 bit r/o Interrupt Status Reg *****/ - /* Bit 15..14: reserved */ -#define PHY_L_IS_AN_F (1<<13) /* Bit 13: Auto-Negotiation fault */ - /* Bit 12: not described */ -#define PHY_L_IS_CROSS (1<<11) /* Bit 11: Crossover used */ -#define PHY_L_IS_POL (1<<10) /* Bit 10: Polarity correct. used */ -#define PHY_L_IS_SS (1<<9) /* Bit 9: Smart Speed Downgrade */ -#define PHY_L_IS_CFULL (1<<8) /* Bit 8: Counter Full */ -#define PHY_L_IS_AN_C (1<<7) /* Bit 7: AutoNeg Complete */ -#define PHY_L_IS_SPEED (1<<6) /* Bit 6: Speed Changed */ -#define PHY_L_IS_DUP (1<<5) /* Bit 5: Duplex Changed */ -#define PHY_L_IS_LS (1<<4) /* Bit 4: Link Status Changed */ -#define PHY_L_IS_ISOL (1<<3) /* Bit 3: Isolate Occured */ -#define PHY_L_IS_MDINT (1<<2) /* Bit 2: (ro) STAT: MII Int Pending */ -#define PHY_L_IS_INTEN (1<<1) /* Bit 1: ENAB: Enable IRQs */ -#define PHY_L_IS_FORCE (1<<0) /* Bit 0: ENAB: Force Interrupt */ - -/* int. mask */ -#define PHY_L_DEF_MSK (PHY_L_IS_LS | PHY_L_IS_ISOL | PHY_L_IS_INTEN) - -/***** PHY_LONE_LED_CFG 16 bit r/w LED Configuration Reg *****/ -#define PHY_L_LC_LEDC (3<<14) /* Bit 15..14: Col/Blink/On/Off */ -#define PHY_L_LC_LEDR (3<<12) /* Bit 13..12: Rx/Blink/On/Off */ -#define PHY_L_LC_LEDT (3<<10) /* Bit 11..10: Tx/Blink/On/Off */ -#define PHY_L_LC_LEDG (3<<8) /* Bit 9..8: Giga/Blink/On/Off */ -#define PHY_L_LC_LEDS (3<<6) /* Bit 7..6: 10-100/Blink/On/Off */ -#define PHY_L_LC_LEDL (3<<4) /* Bit 5..4: Link/Blink/On/Off */ -#define PHY_L_LC_LEDF (3<<2) /* Bit 3..2: Duplex/Blink/On/Off */ -#define PHY_L_LC_PSTRECH (1<<1) /* Bit 1: Strech LED Pulses */ -#define PHY_L_LC_FREQ (1<<0) /* Bit 0: 30/100 ms */ - -/***** PHY_LONE_PORT_CTRL 16 bit r/w Port Control Reg *****/ -#define PHY_L_PC_TX_TCLK (1<<15) /* Bit 15: Enable TX_TCLK */ - /* Bit 14: reserved */ -#define PHY_L_PC_ALT_NP (1<<13) /* Bit 14: Alternate Next Page */ -#define PHY_L_PC_GMII_ALT (1<<12) /* Bit 13: Alternate GMII driver */ - /* Bit 11: reserved */ -#define PHY_L_PC_TEN_CRS (1<<10) /* Bit 10: Extend CRS*/ - /* Bit 9..0: not described */ - -/***** PHY_LONE_CIM 16 bit r/o CIM Reg *****/ -#define PHY_L_CIM_ISOL (255<<8)/* Bit 15..8: Isolate Count */ -#define PHY_L_CIM_FALSE_CAR (255<<0)/* Bit 7..0: False Carrier Count */ - - -/* - * Pause Bits (PHY_L_AN_ASP and PHY_L_AN_PC) encoding - */ -#define PHY_L_P_NO_PAUSE (0<<10) /* Bit 11..10: no Pause Mode */ -#define PHY_L_P_SYM_MD (1<<10) /* Bit 11..10: symmetric Pause Mode */ -#define PHY_L_P_ASYM_MD (2<<10) /* Bit 11..10: asymmetric Pause Mode */ -#define PHY_L_P_BOTH_MD (3<<10) /* Bit 11..10: both Pause Mode */ - - -/* - * National-Specific - */ -/***** PHY_NAT_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/ -#define PHY_N_1000C_TEST (7<<13) /* Bit 15..13: Test Modes */ -#define PHY_N_1000C_MSE (1<<12) /* Bit 12: Master/Slave Enable */ -#define PHY_N_1000C_MSC (1<<11) /* Bit 11: M/S Configuration */ -#define PHY_N_1000C_RD (1<<10) /* Bit 10: Repeater/DTE */ -#define PHY_N_1000C_AFD (1<<9) /* Bit 9: Advertise Full Duplex */ -#define PHY_N_1000C_AHD (1<<8) /* Bit 8: Advertise Half Duplex */ -#define PHY_N_1000C_APC (1<<7) /* Bit 7: Asymmetric Pause Cap. */ - /* Bit 6..0: reserved */ - -/***** PHY_NAT_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/ -#define PHY_N_1000S_MSF (1<<15) /* Bit 15: Master/Slave Fault */ -#define PHY_N_1000S_MSR (1<<14) /* Bit 14: Master/Slave Result */ -#define PHY_N_1000S_LRS (1<<13) /* Bit 13: Local Receiver Status */ -#define PHY_N_1000S_RRS (1<<12) /* Bit 12: Remote Receiver Status*/ -#define PHY_N_1000S_LP_FD (1<<11) /* Bit 11: Link Partner can FD */ -#define PHY_N_1000S_LP_HD (1<<10) /* Bit 10: Link Partner can HD */ -#define PHY_N_1000C_LP_APC (1<<9) /* Bit 9: LP Asym. Pause Cap. */ - /* Bit 8: reserved */ -#define PHY_N_1000S_IEC 0xff /* Bit 7..0: Idle Error Count */ - -/***** PHY_NAT_EXT_STAT 16 bit r/o Extended Status Register *****/ -#define PHY_N_ES_X_FD_CAP (1<<15) /* Bit 15: 1000Base-X FD capable */ -#define PHY_N_ES_X_HD_CAP (1<<14) /* Bit 14: 1000Base-X HD capable */ -#define PHY_N_ES_T_FD_CAP (1<<13) /* Bit 13: 1000Base-T FD capable */ -#define PHY_N_ES_T_HD_CAP (1<<12) /* Bit 12: 1000Base-T HD capable */ - /* Bit 11..0: reserved */ - -/* todo: those are still missing */ -/***** PHY_NAT_EXT_CTRL1 16 bit r/o Extended Control Reg1 *****/ -/***** PHY_NAT_Q_STAT1 16 bit r/o Quick Status Reg1 *****/ -/***** PHY_NAT_10B_OP 16 bit r/o 10Base-T Operations Reg *****/ -/***** PHY_NAT_EXT_CTRL2 16 bit r/o Extended Control Reg1 *****/ -/***** PHY_NAT_Q_STAT2 16 bit r/o Quick Status Reg2 *****/ -/***** PHY_NAT_PHY_ADDR 16 bit r/o PHY Address Register *****/ - -/* - * Marvell-Specific - */ -/***** PHY_MARV_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/ -/***** PHY_MARV_AUNE_LP 16 bit r/w Link Part Ability Reg *****/ -#define PHY_M_AN_NXT_PG BIT_15 /* Request Next Page */ -#define PHY_M_AN_ACK BIT_14 /* (ro) Acknowledge Received */ -#define PHY_M_AN_RF BIT_13 /* Remote Fault */ - /* Bit 12: reserved */ -#define PHY_M_AN_ASP BIT_11 /* Asymmetric Pause */ -#define PHY_M_AN_PC BIT_10 /* MAC Pause implemented */ -#define PHY_M_AN_100_FD BIT_8 /* Advertise 100Base-TX Full Duplex */ -#define PHY_M_AN_100_HD BIT_7 /* Advertise 100Base-TX Half Duplex */ -#define PHY_M_AN_10_FD BIT_6 /* Advertise 10Base-TX Full Duplex */ -#define PHY_M_AN_10_HD BIT_5 /* Advertise 10Base-TX Half Duplex */ - -/* special defines for FIBER (88E1011S only) */ -#define PHY_M_AN_ASP_X BIT_8 /* Asymmetric Pause */ -#define PHY_M_AN_PC_X BIT_7 /* MAC Pause implemented */ -#define PHY_M_AN_1000X_AHD BIT_6 /* Advertise 10000Base-X Half Duplex */ -#define PHY_M_AN_1000X_AFD BIT_5 /* Advertise 10000Base-X Full Duplex */ - -/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */ -#define PHY_M_P_NO_PAUSE_X (0<<7) /* Bit 8.. 7: no Pause Mode */ -#define PHY_M_P_SYM_MD_X (1<<7) /* Bit 8.. 7: symmetric Pause Mode */ -#define PHY_M_P_ASYM_MD_X (2<<7) /* Bit 8.. 7: asymmetric Pause Mode */ -#define PHY_M_P_BOTH_MD_X (3<<7) /* Bit 8.. 7: both Pause Mode */ - -/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/ -#define PHY_M_1000C_TEST (7<<13) /* Bit 15..13: Test Modes */ -#define PHY_M_1000C_MSE (1<<12) /* Bit 12: Manual Master/Slave Enable */ -#define PHY_M_1000C_MSC (1<<11) /* Bit 11: M/S Configuration (1=Master) */ -#define PHY_M_1000C_MPD (1<<10) /* Bit 10: Multi-Port Device */ -#define PHY_M_1000C_AFD (1<<9) /* Bit 9: Advertise Full Duplex */ -#define PHY_M_1000C_AHD (1<<8) /* Bit 8: Advertise Half Duplex */ - /* Bit 7..0: reserved */ - -/***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/ -#define PHY_M_PC_TX_FFD_MSK (3<<14) /* Bit 15..14: Tx FIFO Depth Mask */ -#define PHY_M_PC_RX_FFD_MSK (3<<12) /* Bit 13..12: Rx FIFO Depth Mask */ -#define PHY_M_PC_ASS_CRS_TX (1<<11) /* Bit 11: Assert CRS on Transmit */ -#define PHY_M_PC_FL_GOOD (1<<10) /* Bit 10: Force Link Good */ -#define PHY_M_PC_EN_DET_MSK (3<<8) /* Bit 9.. 8: Energy Detect Mask */ -#define PHY_M_PC_ENA_EXT_D (1<<7) /* Bit 7: Enable Ext. Distance (10BT) */ -#define PHY_M_PC_MDIX_MSK (3<<5) /* Bit 6.. 5: MDI/MDIX Config. Mask */ -#define PHY_M_PC_DIS_125CLK (1<<4) /* Bit 4: Disable 125 CLK */ -#define PHY_M_PC_MAC_POW_UP (1<<3) /* Bit 3: MAC Power up */ -#define PHY_M_PC_SQE_T_ENA (1<<2) /* Bit 2: SQE Test Enabled */ -#define PHY_M_PC_POL_R_DIS (1<<1) /* Bit 1: Polarity Reversal Disabled */ -#define PHY_M_PC_DIS_JABBER (1<<0) /* Bit 0: Disable Jabber */ - -#define PHY_M_PC_EN_DET SHIFT8(2) /* Energy Detect (Mode 1) */ -#define PHY_M_PC_EN_DET_PLUS SHIFT8(3) /* Energy Detect Plus (Mode 2) */ - -#define PHY_M_PC_MDI_XMODE(x) SHIFT5(x) -#define PHY_M_PC_MAN_MDI 0 /* 00 = Manual MDI configuration */ -#define PHY_M_PC_MAN_MDIX 1 /* 01 = Manual MDIX configuration */ -#define PHY_M_PC_ENA_AUTO 3 /* 11 = Enable Automatic Crossover */ - -/***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/ -#define PHY_M_PS_SPEED_MSK (3<<14) /* Bit 15..14: Speed Mask */ -#define PHY_M_PS_SPEED_1000 (1<<15) /* 10 = 1000 Mbps */ -#define PHY_M_PS_SPEED_100 (1<<14) /* 01 = 100 Mbps */ -#define PHY_M_PS_SPEED_10 0 /* 00 = 10 Mbps */ -#define PHY_M_PS_FULL_DUP (1<<13) /* Bit 13: Full Duplex */ -#define PHY_M_PS_PAGE_REC (1<<12) /* Bit 12: Page Received */ -#define PHY_M_PS_SPDUP_RES (1<<11) /* Bit 11: Speed & Duplex Resolved */ -#define PHY_M_PS_LINK_UP (1<<10) /* Bit 10: Link Up */ -#define PHY_M_PS_CABLE_MSK (3<<7) /* Bit 9.. 7: Cable Length Mask */ -#define PHY_M_PS_MDI_X_STAT (1<<6) /* Bit 6: MDI Crossover Stat (1=MDIX) */ -#define PHY_M_PS_DOWNS_STAT (1<<5) /* Bit 5: Downshift Status (1=downsh.) */ -#define PHY_M_PS_ENDET_STAT (1<<4) /* Bit 4: Energy Detect Status (1=act) */ -#define PHY_M_PS_TX_P_EN (1<<3) /* Bit 3: Tx Pause Enabled */ -#define PHY_M_PS_RX_P_EN (1<<2) /* Bit 2: Rx Pause Enabled */ -#define PHY_M_PS_POL_REV (1<<1) /* Bit 1: Polarity Reversed */ -#define PHY_M_PC_JABBER (1<<0) /* Bit 0: Jabber */ - -#define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN) - -/***** PHY_MARV_INT_MASK 16 bit r/w Interrupt Mask Reg *****/ -/***** PHY_MARV_INT_STAT 16 bit r/o Interrupt Status Reg *****/ -#define PHY_M_IS_AN_ERROR (1<<15) /* Bit 15: Auto-Negotiation Error */ -#define PHY_M_IS_LSP_CHANGE (1<<14) /* Bit 14: Link Speed Changed */ -#define PHY_M_IS_DUP_CHANGE (1<<13) /* Bit 13: Duplex Mode Changed */ -#define PHY_M_IS_AN_PR (1<<12) /* Bit 12: Page Received */ -#define PHY_M_IS_AN_COMPL (1<<11) /* Bit 11: Auto-Negotiation Completed */ -#define PHY_M_IS_LST_CHANGE (1<<10) /* Bit 10: Link Status Changed */ -#define PHY_M_IS_SYMB_ERROR (1<<9) /* Bit 9: Symbol Error */ -#define PHY_M_IS_FALSE_CARR (1<<8) /* Bit 8: False Carrier */ -#define PHY_M_IS_FIFO_ERROR (1<<7) /* Bit 7: FIFO Overflow/Underrun Error */ -#define PHY_M_IS_MDI_CHANGE (1<<6) /* Bit 6: MDI Crossover Changed */ -#define PHY_M_IS_DOWNSH_DET (1<<5) /* Bit 5: Downshift Detected */ -#define PHY_M_IS_END_CHANGE (1<<4) /* Bit 4: Energy Detect Changed */ - /* Bit 3..2: reserved */ -#define PHY_M_IS_POL_CHANGE (1<<1) /* Bit 1: Polarity Changed */ -#define PHY_M_IS_JABBER (1<<0) /* Bit 0: Jabber */ - -#define PHY_M_DEF_MSK (PHY_M_IS_AN_ERROR | PHY_M_IS_AN_PR | \ - PHY_M_IS_LST_CHANGE | PHY_M_IS_FIFO_ERROR) - -/***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/ -#define PHY_M_EC_M_DSC_MSK (3<<10) /* Bit 11..10: Master downshift counter */ -#define PHY_M_EC_S_DSC_MSK (3<<8) /* Bit 9.. 8: Slave downshift counter */ -#define PHY_M_EC_MAC_S_MSK (7<<4) /* Bit 6.. 4: Def. MAC interface speed */ -#define PHY_M_EC_FIB_AN_ENA (1<<3) /* Bit 3: Fiber Auto-Neg. Enable */ - -#define PHY_M_EC_M_DSC(x) SHIFT10(x) /* 00=1x; 01=2x; 10=3x; 11=4x */ -#define PHY_M_EC_S_DSC(x) SHIFT8(x) /* 00=dis; 01=1x; 10=2x; 11=3x */ -#define PHY_M_EC_MAC_S(x) SHIFT4(x) /* 01X=0; 110=2.5; 111=25 (MHz) */ - -#define MAC_TX_CLK_0_MHZ 2 -#define MAC_TX_CLK_2_5_MHZ 6 -#define MAC_TX_CLK_25_MHZ 7 - -/***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/ -#define PHY_M_LEDC_DIS_LED (1<<15) /* Bit 15: Disable LED */ -#define PHY_M_LEDC_PULS_MSK (7<<12) /* Bit 14..12: Pulse Stretch Mask */ -#define PHY_M_LEDC_F_INT (1<<11) /* Bit 11: Force Interrupt */ -#define PHY_M_LEDC_BL_R_MSK (7<<8) /* Bit 10.. 8: Blink Rate Mask */ - /* Bit 7.. 5: reserved */ -#define PHY_M_LEDC_LINK_MSK (3<<3) /* Bit 4.. 3: Link Control Mask */ -#define PHY_M_LEDC_DP_CTRL (1<<2) /* Bit 2: Duplex Control */ -#define PHY_M_LEDC_RX_CTRL (1<<1) /* Bit 1: Rx activity / Link */ -#define PHY_M_LEDC_TX_CTRL (1<<0) /* Bit 0: Tx activity / Link */ - -#define PHY_M_LED_PULS_DUR(x) SHIFT12(x) /* Pulse Stretch Duration */ - -#define PULS_NO_STR 0 /* no pulse stretching */ -#define PULS_21MS 1 /* 21 ms to 42 ms */ -#define PULS_42MS 2 /* 42 ms to 84 ms */ -#define PULS_84MS 3 /* 84 ms to 170 ms */ -#define PULS_170MS 4 /* 170 ms to 340 ms */ -#define PULS_340MS 5 /* 340 ms to 670 ms */ -#define PULS_670MS 6 /* 670 ms to 1.3 s */ -#define PULS_1300MS 7 /* 1.3 s to 2.7 s */ - -#define PHY_M_LED_BLINK_RT(x) SHIFT8(x) /* Blink Rate */ - -#define BLINK_42MS 0 /* 42 ms */ -#define BLINK_84MS 1 /* 84 ms */ -#define BLINK_170MS 2 /* 170 ms */ -#define BLINK_340MS 3 /* 340 ms */ -#define BLINK_670MS 4 /* 670 ms */ - /* values 5 - 7: reserved */ - -/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/ -#define PHY_M_LED_MO_DUP(x) SHIFT10(x) /* Bit 11..10: Duplex */ -#define PHY_M_LED_MO_10(x) SHIFT8(x) /* Bit 9.. 8: Link 10 */ -#define PHY_M_LED_MO_100(x) SHIFT6(x) /* Bit 7.. 6: Link 100 */ -#define PHY_M_LED_MO_1000(x) SHIFT4(x) /* Bit 5.. 4: Link 1000 */ -#define PHY_M_LED_MO_RX(x) SHIFT2(x) /* Bit 3.. 2: Rx */ -#define PHY_M_LED_MO_TX(x) SHIFT0(x) /* Bit 1.. 0: Tx */ - -#define MO_LED_NORM 0 -#define MO_LED_BLINK 1 -#define MO_LED_OFF 2 -#define MO_LED_ON 3 - -/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/ - /* Bit 15.. 7: reserved */ -#define PHY_M_EC2_FI_IMPED (1<<6) /* Bit 6: Fiber Input Impedance */ -#define PHY_M_EC2_FO_IMPED (1<<5) /* Bit 5: Fiber Output Impedance */ -#define PHY_M_EC2_FO_M_CLK (1<<4) /* Bit 4: Fiber Mode Clock Enable */ -#define PHY_M_EC2_FO_BOOST (1<<3) /* Bit 3: Fiber Output Boost */ -#define PHY_M_EC2_FO_AM_MSK 7 /* Bit 2.. 0: Fiber Output Amplitude */ - -/***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/ -#define PHY_M_FC_AUTO_SEL (1<<15) /* Bit 15: Fiber/Copper Auto Sel. dis. */ -#define PHY_M_FC_AN_REG_ACC (1<<14) /* Bit 14: Fiber/Copper Autoneg. reg acc */ -#define PHY_M_FC_RESULUTION (1<<13) /* Bit 13: Fiber/Copper Resulution */ -#define PHY_M_SER_IF_AN_BP (1<<12) /* Bit 12: Ser IF autoneg. bypass enable */ -#define PHY_M_SER_IF_BP_ST (1<<11) /* Bit 11: Ser IF autoneg. bypass status */ -#define PHY_M_IRQ_POLARITY (1<<10) /* Bit 10: IRQ polarity */ - /* Bit 9..4: reserved */ -#define PHY_M_UNDOC1 (1<< 7) /* undocumented bit !! */ -#define PHY_M_MODE_MASK (0xf<<0)/* Bit 3..0: copy of HWCFG MODE[3:0] */ - - -/***** PHY_MARV_CABLE_DIAG 16 bit r/o Cable Diagnostic Reg *****/ -#define PHY_M_CABD_ENA_TEST (1<<15) /* Bit 15: Enable Test */ -#define PHY_M_CABD_STAT_MSK (3<<13) /* Bit 14..13: Status */ - /* Bit 12.. 8: reserved */ -#define PHY_M_CABD_DIST_MSK 0xff /* Bit 7.. 0: Distance */ - -/* values for Cable Diagnostic Status (11=fail; 00=OK; 10=open; 01=short) */ -#define CABD_STAT_NORMAL 0 -#define CABD_STAT_SHORT 1 -#define CABD_STAT_OPEN 2 -#define CABD_STAT_FAIL 3 - - -/* - * GMAC registers - * - * The GMAC registers are 16 or 32 bits wide. - * The GMACs host processor interface is 16 bits wide, - * therefore ALL registers will be addressed with 16 bit accesses. - * - * The following macros are provided to access the GMAC registers - * GM_IN16(), GM_OUT16, GM_IN32(), GM_OUT32(), GM_INADR(), GM_OUTADR(), - * GM_INHASH(), and GM_OUTHASH(). - * The macros are defined in SkGeHw.h. - * - * Note: NA reg = Network Address e.g DA, SA etc. - * - */ - -/* Port Registers */ -#define GM_GP_STAT 0x0000 /* 16 bit r/o General Purpose Status */ -#define GM_GP_CTRL 0x0004 /* 16 bit r/w General Purpose Control */ -#define GM_TX_CTRL 0x0008 /* 16 bit r/w Transmit Control Reg. */ -#define GM_RX_CTRL 0x000c /* 16 bit r/w Receive Control Reg. */ -#define GM_TX_FLOW_CTRL 0x0010 /* 16 bit r/w Transmit Flow-Control */ -#define GM_TX_PARAM 0x0014 /* 16 bit r/w Transmit Parameter Reg. */ -#define GM_SERIAL_MODE 0x0018 /* 16 bit r/w Serial Mode Register */ - -/* Source Address Registers */ -#define GM_SRC_ADDR_1L 0x001c /* 16 bit r/w Source Address 1 (low) */ -#define GM_SRC_ADDR_1M 0x0020 /* 16 bit r/w Source Address 1 (middle) */ -#define GM_SRC_ADDR_1H 0x0024 /* 16 bit r/w Source Address 1 (high) */ -#define GM_SRC_ADDR_2L 0x0028 /* 16 bit r/w Source Address 2 (low) */ -#define GM_SRC_ADDR_2M 0x002c /* 16 bit r/w Source Address 2 (middle) */ -#define GM_SRC_ADDR_2H 0x0030 /* 16 bit r/w Source Address 2 (high) */ - -/* Multicast Address Hash Registers */ -#define GM_MC_ADDR_H1 0x0034 /* 16 bit r/w Multicast Address Hash 1 */ -#define GM_MC_ADDR_H2 0x0038 /* 16 bit r/w Multicast Address Hash 2 */ -#define GM_MC_ADDR_H3 0x003c /* 16 bit r/w Multicast Address Hash 3 */ -#define GM_MC_ADDR_H4 0x0040 /* 16 bit r/w Multicast Address Hash 4 */ - -/* Interrupt Source Registers */ -#define GM_TX_IRQ_SRC 0x0044 /* 16 bit r/o Tx Overflow IRQ Source */ -#define GM_RX_IRQ_SRC 0x0048 /* 16 bit r/o Rx Overflow IRQ Source */ -#define GM_TR_IRQ_SRC 0x004c /* 16 bit r/o Tx/Rx Over. IRQ Source */ - -/* Interrupt Mask Registers */ -#define GM_TX_IRQ_MSK 0x0050 /* 16 bit r/w Tx Overflow IRQ Mask */ -#define GM_RX_IRQ_MSK 0x0054 /* 16 bit r/w Rx Overflow IRQ Mask */ -#define GM_TR_IRQ_MSK 0x0058 /* 16 bit r/w Tx/Rx Over. IRQ Mask */ - -/* Serial Management Interface (SMI) Registers */ -#define GM_SMI_CTRL 0x0080 /* 16 bit r/w SMI Control Register */ -#define GM_SMI_DATA 0x0084 /* 16 bit r/w SMI Data Register */ -#define GM_PHY_ADDR 0x0088 /* 16 bit r/w GPHY Address Register */ - -/* MIB Counters */ -#define GM_MIB_CNT_BASE 0x0100 /* Base Address of MIB Counters */ -#define GM_MIB_CNT_SIZE 44 /* Number of MIB Counters */ - -/* - * MIB Counters base address definitions (low word) - - * use offset 4 for access to high word (32 bit r/o) - */ -#define GM_RXF_UC_OK \ - (GM_MIB_CNT_BASE + 0) /* Unicast Frames Received OK */ -#define GM_RXF_BC_OK \ - (GM_MIB_CNT_BASE + 8) /* Broadcast Frames Received OK */ -#define GM_RXF_MPAUSE \ - (GM_MIB_CNT_BASE + 16) /* Pause MAC Ctrl Frames Received */ -#define GM_RXF_MC_OK \ - (GM_MIB_CNT_BASE + 24) /* Multicast Frames Received OK */ -#define GM_RXF_FCS_ERR \ - (GM_MIB_CNT_BASE + 32) /* Rx Frame Check Seq. Error */ - /* GM_MIB_CNT_BASE + 40: reserved */ -#define GM_RXO_OK_LO \ - (GM_MIB_CNT_BASE + 48) /* Octets Received OK Low */ -#define GM_RXO_OK_HI \ - (GM_MIB_CNT_BASE + 56) /* Octets Received OK High */ -#define GM_RXO_ERR_LO \ - (GM_MIB_CNT_BASE + 64) /* Octets Received Invalid Low */ -#define GM_RXO_ERR_HI \ - (GM_MIB_CNT_BASE + 72) /* Octets Received Invalid High */ -#define GM_RXF_SHT \ - (GM_MIB_CNT_BASE + 80) /* Frames <64 Byte Received OK */ -#define GM_RXE_FRAG \ - (GM_MIB_CNT_BASE + 88) /* Frames <64 Byte Received with FCS Err */ -#define GM_RXF_64B \ - (GM_MIB_CNT_BASE + 96) /* 64 Byte Rx Frame */ -#define GM_RXF_127B \ - (GM_MIB_CNT_BASE + 104) /* 65-127 Byte Rx Frame */ -#define GM_RXF_255B \ - (GM_MIB_CNT_BASE + 112) /* 128-255 Byte Rx Frame */ -#define GM_RXF_511B \ - (GM_MIB_CNT_BASE + 120) /* 256-511 Byte Rx Frame */ -#define GM_RXF_1023B \ - (GM_MIB_CNT_BASE + 128) /* 512-1023 Byte Rx Frame */ -#define GM_RXF_1518B \ - (GM_MIB_CNT_BASE + 136) /* 1024-1518 Byte Rx Frame */ -#define GM_RXF_MAX_SZ \ - (GM_MIB_CNT_BASE + 144) /* 1519-MaxSize Byte Rx Frame */ -#define GM_RXF_LNG_ERR \ - (GM_MIB_CNT_BASE + 152) /* Rx Frame too Long Error */ -#define GM_RXF_JAB_PKT \ - (GM_MIB_CNT_BASE + 160) /* Rx Jabber Packet Frame */ - /* GM_MIB_CNT_BASE + 168: reserved */ -#define GM_RXE_FIFO_OV \ - (GM_MIB_CNT_BASE + 176) /* Rx FIFO overflow Event */ - /* GM_MIB_CNT_BASE + 184: reserved */ -#define GM_TXF_UC_OK \ - (GM_MIB_CNT_BASE + 192) /* Unicast Frames Xmitted OK */ -#define GM_TXF_BC_OK \ - (GM_MIB_CNT_BASE + 200) /* Broadcast Frames Xmitted OK */ -#define GM_TXF_MPAUSE \ - (GM_MIB_CNT_BASE + 208) /* Pause MAC Ctrl Frames Xmitted */ -#define GM_TXF_MC_OK \ - (GM_MIB_CNT_BASE + 216) /* Multicast Frames Xmitted OK */ -#define GM_TXO_OK_LO \ - (GM_MIB_CNT_BASE + 224) /* Octets Transmitted OK Low */ -#define GM_TXO_OK_HI \ - (GM_MIB_CNT_BASE + 232) /* Octets Transmitted OK High */ -#define GM_TXF_64B \ - (GM_MIB_CNT_BASE + 240) /* 64 Byte Tx Frame */ -#define GM_TXF_127B \ - (GM_MIB_CNT_BASE + 248) /* 65-127 Byte Tx Frame */ -#define GM_TXF_255B \ - (GM_MIB_CNT_BASE + 256) /* 128-255 Byte Tx Frame */ -#define GM_TXF_511B \ - (GM_MIB_CNT_BASE + 264) /* 256-511 Byte Tx Frame */ -#define GM_TXF_1023B \ - (GM_MIB_CNT_BASE + 272) /* 512-1023 Byte Tx Frame */ -#define GM_TXF_1518B \ - (GM_MIB_CNT_BASE + 280) /* 1024-1518 Byte Tx Frame */ -#define GM_TXF_MAX_SZ \ - (GM_MIB_CNT_BASE + 288) /* 1519-MaxSize Byte Tx Frame */ - /* GM_MIB_CNT_BASE + 296: reserved */ -#define GM_TXF_COL \ - (GM_MIB_CNT_BASE + 304) /* Tx Collision */ -#define GM_TXF_LAT_COL \ - (GM_MIB_CNT_BASE + 312) /* Tx Late Collision */ -#define GM_TXF_ABO_COL \ - (GM_MIB_CNT_BASE + 320) /* Tx aborted due to Exces. Col. */ -#define GM_TXF_MUL_COL \ - (GM_MIB_CNT_BASE + 328) /* Tx Multiple Collision */ -#define GM_TXF_SNG_COL \ - (GM_MIB_CNT_BASE + 336) /* Tx Single Collision */ -#define GM_TXE_FIFO_UR \ - (GM_MIB_CNT_BASE + 344) /* Tx FIFO Underrun Event */ - -/*----------------------------------------------------------------------------*/ -/* - * GMAC Bit Definitions - * - * If the bit access behaviour differs from the register access behaviour - * (r/w, r/o) this is documented after the bit number. - * The following bit access behaviours are used: - * (sc) self clearing - * (r/o) read only - */ - -/* GM_GP_STAT 16 bit r/o General Purpose Status Register */ -#define GM_GPSR_SPEED (1<<15) /* Bit 15: Port Speed (1 = 100 Mbps) */ -#define GM_GPSR_DUPLEX (1<<14) /* Bit 14: Duplex Mode (1 = Full) */ -#define GM_GPSR_FC_TX_DIS (1<<13) /* Bit 13: Tx Flow-Control Mode Disabled */ -#define GM_GPSR_LINK_UP (1<<12) /* Bit 12: Link Up Status */ -#define GM_GPSR_PAUSE (1<<11) /* Bit 11: Pause State */ -#define GM_GPSR_TX_ACTIVE (1<<10) /* Bit 10: Tx in Progress */ -#define GM_GPSR_EXC_COL (1<<9) /* Bit 9: Excessive Collisions Occured */ -#define GM_GPSR_LAT_COL (1<<8) /* Bit 8: Late Collisions Occured */ - /* Bit 7..6: reserved */ -#define GM_GPSR_PHY_ST_CH (1<<5) /* Bit 5: PHY Status Change */ -#define GM_GPSR_GIG_SPEED (1<<4) /* Bit 4: Gigabit Speed (1 = 1000 Mbps) */ -#define GM_GPSR_PART_MODE (1<<3) /* Bit 3: Partition mode */ -#define GM_GPSR_FC_RX_DIS (1<<2) /* Bit 2: Rx Flow-Control Mode Disabled */ -#define GM_GPSR_PROM_EN (1<<1) /* Bit 1: Promiscuous Mode Enabled */ - /* Bit 0: reserved */ - -/* GM_GP_CTRL 16 bit r/w General Purpose Control Register */ - /* Bit 15: reserved */ -#define GM_GPCR_PROM_ENA (1<<14) /* Bit 14: Enable Promiscuous Mode */ -#define GM_GPCR_FC_TX_DIS (1<<13) /* Bit 13: Disable Tx Flow-Control Mode */ -#define GM_GPCR_TX_ENA (1<<12) /* Bit 12: Enable Transmit */ -#define GM_GPCR_RX_ENA (1<<11) /* Bit 11: Enable Receive */ -#define GM_GPCR_BURST_ENA (1<<10) /* Bit 10: Enable Burst Mode */ -#define GM_GPCR_LOOP_ENA (1<<9) /* Bit 9: Enable MAC Loopback Mode */ -#define GM_GPCR_PART_ENA (1<<8) /* Bit 8: Enable Partition Mode */ -#define GM_GPCR_GIGS_ENA (1<<7) /* Bit 7: Gigabit Speed (1000 Mbps) */ -#define GM_GPCR_FL_PASS (1<<6) /* Bit 6: Force Link Pass */ -#define GM_GPCR_DUP_FULL (1<<5) /* Bit 5: Full Duplex Mode */ -#define GM_GPCR_FC_RX_DIS (1<<4) /* Bit 4: Disable Rx Flow-Control Mode */ -#define GM_GPCR_SPEED_100 (1<<3) /* Bit 3: Port Speed 100 Mbps */ -#define GM_GPCR_AU_DUP_DIS (1<<2) /* Bit 2: Disable Auto-Update Duplex */ -#define GM_GPCR_AU_FCT_DIS (1<<1) /* Bit 1: Disable Auto-Update Flow-C. */ -#define GM_GPCR_AU_SPD_DIS (1<<0) /* Bit 0: Disable Auto-Update Speed */ - -#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100) -#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS |\ - GM_GPCR_AU_SPD_DIS) - -/* GM_TX_CTRL 16 bit r/w Transmit Control Register */ -#define GM_TXCR_FORCE_JAM (1<<15) /* Bit 15: Force Jam / Flow-Control */ -#define GM_TXCR_CRC_DIS (1<<14) /* Bit 14: Disable insertion of CRC */ -#define GM_TXCR_PAD_DIS (1<<13) /* Bit 13: Disable padding of packets */ -#define GM_TXCR_COL_THR_MSK (7<<10) /* Bit 12..10: Collision Threshold */ - -#define TX_COL_THR(x) (SHIFT10(x) & GM_TXCR_COL_THR_MSK) - -#define TX_COL_DEF 0x04 - -/* GM_RX_CTRL 16 bit r/w Receive Control Register */ -#define GM_RXCR_UCF_ENA (1<<15) /* Bit 15: Enable Unicast filtering */ -#define GM_RXCR_MCF_ENA (1<<14) /* Bit 14: Enable Multicast filtering */ -#define GM_RXCR_CRC_DIS (1<<13) /* Bit 13: Remove 4-byte CRC */ -#define GM_RXCR_PASS_FC (1<<12) /* Bit 12: Pass FC packets to FIFO */ - -/* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */ -#define GM_TXPA_JAMLEN_MSK (0x03<<14) /* Bit 15..14: Jam Length */ -#define GM_TXPA_JAMIPG_MSK (0x1f<<9) /* Bit 13..9: Jam IPG */ -#define GM_TXPA_JAMDAT_MSK (0x1f<<4) /* Bit 8..4: IPG Jam to Data */ - /* Bit 3..0: reserved */ - -#define TX_JAM_LEN_VAL(x) (SHIFT14(x) & GM_TXPA_JAMLEN_MSK) -#define TX_JAM_IPG_VAL(x) (SHIFT9(x) & GM_TXPA_JAMIPG_MSK) -#define TX_IPG_JAM_DATA(x) (SHIFT4(x) & GM_TXPA_JAMDAT_MSK) - -#define TX_JAM_LEN_DEF 0x03 -#define TX_JAM_IPG_DEF 0x0b -#define TX_IPG_JAM_DEF 0x1c - -/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */ -#define GM_SMOD_DATABL_MSK (0x1f<<11) /* Bit 15..11: Data Blinder (r/o) */ -#define GM_SMOD_LIMIT_4 (1<<10) /* Bit 10: 4 consecutive Tx trials */ -#define GM_SMOD_VLAN_ENA (1<<9) /* Bit 9: Enable VLAN (Max. Frame Len) */ -#define GM_SMOD_JUMBO_ENA (1<<8) /* Bit 8: Enable Jumbo (Max. Frame Len) */ - /* Bit 7..5: reserved */ -#define GM_SMOD_IPG_MSK 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */ - -#define DATA_BLIND_VAL(x) (SHIFT11(x) & GM_SMOD_DATABL_MSK) -#define DATA_BLIND_DEF 0x04 - -#define IPG_DATA_VAL(x) (x & GM_SMOD_IPG_MSK) -#define IPG_DATA_DEF 0x1e - -/* GM_SMI_CTRL 16 bit r/w SMI Control Register */ -#define GM_SMI_CT_PHY_A_MSK (0x1f<<11) /* Bit 15..11: PHY Device Address */ -#define GM_SMI_CT_REG_A_MSK (0x1f<<6) /* Bit 10.. 6: PHY Register Address */ -#define GM_SMI_CT_OP_RD (1<<5) /* Bit 5: OpCode Read (0=Write)*/ -#define GM_SMI_CT_RD_VAL (1<<4) /* Bit 4: Read Valid (Read completed) */ -#define GM_SMI_CT_BUSY (1<<3) /* Bit 3: Busy (Operation in progress) */ - /* Bit 2..0: reserved */ - -#define GM_SMI_CT_PHY_AD(x) (SHIFT11(x) & GM_SMI_CT_PHY_A_MSK) -#define GM_SMI_CT_REG_AD(x) (SHIFT6(x) & GM_SMI_CT_REG_A_MSK) - - /* GM_PHY_ADDR 16 bit r/w GPHY Address Register */ - /* Bit 15..6: reserved */ -#define GM_PAR_MIB_CLR (1<<5) /* Bit 5: Set MIB Clear Counter Mode */ -#define GM_PAR_MIB_TST (1<<4) /* Bit 4: MIB Load Counter (Test Mode) */ - /* Bit 3..0: reserved */ - -/* Receive Frame Status Encoding */ -#define GMR_FS_LEN (0xffffUL<<16) /* Bit 31..16: Rx Frame Length */ - /* Bit 15..14: reserved */ -#define GMR_FS_VLAN (1L<<13) /* Bit 13: VLAN Packet */ -#define GMR_FS_JABBER (1L<<12) /* Bit 12: Jabber Packet */ -#define GMR_FS_UN_SIZE (1L<<11) /* Bit 11: Undersize Packet */ -#define GMR_FS_MC (1L<<10) /* Bit 10: Multicast Packet */ -#define GMR_FS_BC (1L<<9) /* Bit 9: Broadcast Packet */ -#define GMR_FS_RX_OK (1L<<8) /* Bit 8: Receive OK (Good Packet) */ -#define GMR_FS_GOOD_FC (1L<<7) /* Bit 7: Good Flow-Control Packet */ -#define GMR_FS_BAD_FC (1L<<6) /* Bit 6: Bad Flow-Control Packet */ -#define GMR_FS_MII_ERR (1L<<5) /* Bit 5: MII Error */ -#define GMR_FS_LONG_ERR (1L<<4) /* Bit 4: Too Long Packet */ -#define GMR_FS_FRAGMENT (1L<<3) /* Bit 3: Fragment */ - /* Bit 2: reserved */ -#define GMR_FS_CRC_ERR (1L<<1) /* Bit 1: CRC Error */ -#define GMR_FS_RX_FF_OV (1L<<0) /* Bit 0: Rx FIFO Overflow */ - -/* - * GMR_FS_ANY_ERR (analogous to XMR_FS_ANY_ERR) - */ -#define GMR_FS_ANY_ERR (GMR_FS_CRC_ERR | \ - GMR_FS_LONG_ERR | \ - GMR_FS_MII_ERR | \ - GMR_FS_BAD_FC | \ - GMR_FS_GOOD_FC | \ - GMR_FS_JABBER) - -/* Rx GMAC FIFO Flush Mask (default) */ -#define RX_FF_FL_DEF_MSK (GMR_FS_CRC_ERR | \ - GMR_FS_RX_FF_OV | \ - GMR_FS_MII_ERR | \ - GMR_FS_BAD_FC | \ - GMR_FS_GOOD_FC | \ - GMR_FS_UN_SIZE | \ - GMR_FS_JABBER) - -/* typedefs *******************************************************************/ - - -/* function prototypes ********************************************************/ - -#ifdef __cplusplus -} -#endif /* __cplusplus */ - -#endif /* __INC_XMAC_H */ diff --git a/drivers/net/sk98lin/skaddr.c b/drivers/net/sk98lin/skaddr.c deleted file mode 100644 index 6e6c56aa6d6f..000000000000 --- a/drivers/net/sk98lin/skaddr.c +++ /dev/null @@ -1,1788 +0,0 @@ -/****************************************************************************** - * - * Name: skaddr.c - * Project: Gigabit Ethernet Adapters, ADDR-Module - * Version: $Revision: 1.52 $ - * Date: $Date: 2003/06/02 13:46:15 $ - * Purpose: Manage Addresses (Multicast and Unicast) and Promiscuous Mode. - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * This module is intended to manage multicast addresses, address override, - * and promiscuous mode on GEnesis and Yukon adapters. - * - * Address Layout: - * port address: physical MAC address - * 1st exact match: logical MAC address (GEnesis only) - * 2nd exact match: RLMT multicast (GEnesis only) - * exact match 3-13: OS-specific multicasts (GEnesis only) - * - * Include File Hierarchy: - * - * "skdrv1st.h" - * "skdrv2nd.h" - * - ******************************************************************************/ - -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: skaddr.c,v 1.52 2003/06/02 13:46:15 tschilli Exp $ (C) Marvell."; -#endif /* DEBUG ||!LINT || !SK_SLIM */ - -#define __SKADDR_C - -#ifdef __cplusplus -extern "C" { -#endif /* cplusplus */ - -#include "h/skdrv1st.h" -#include "h/skdrv2nd.h" - -/* defines ********************************************************************/ - - -#define XMAC_POLY 0xEDB88320UL /* CRC32-Poly - XMAC: Little Endian */ -#define GMAC_POLY 0x04C11DB7L /* CRC16-Poly - GMAC: Little Endian */ -#define HASH_BITS 6 /* #bits in hash */ -#define SK_MC_BIT 0x01 - -/* Error numbers and messages. */ - -#define SKERR_ADDR_E001 (SK_ERRBASE_ADDR + 0) -#define SKERR_ADDR_E001MSG "Bad Flags." -#define SKERR_ADDR_E002 (SKERR_ADDR_E001 + 1) -#define SKERR_ADDR_E002MSG "New Error." - -/* typedefs *******************************************************************/ - -/* None. */ - -/* global variables ***********************************************************/ - -/* 64-bit hash values with all bits set. */ - -static const SK_U16 OnesHash[4] = {0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF}; - -/* local variables ************************************************************/ - -#ifdef DEBUG -static int Next0[SK_MAX_MACS] = {0}; -#endif /* DEBUG */ - -static int SkAddrGmacMcAdd(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber, - SK_MAC_ADDR *pMc, int Flags); -static int SkAddrGmacMcClear(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber, - int Flags); -static int SkAddrGmacMcUpdate(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber); -static int SkAddrGmacPromiscuousChange(SK_AC *pAC, SK_IOC IoC, - SK_U32 PortNumber, int NewPromMode); -static int SkAddrXmacMcAdd(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber, - SK_MAC_ADDR *pMc, int Flags); -static int SkAddrXmacMcClear(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber, - int Flags); -static int SkAddrXmacMcUpdate(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber); -static int SkAddrXmacPromiscuousChange(SK_AC *pAC, SK_IOC IoC, - SK_U32 PortNumber, int NewPromMode); - -/* functions ******************************************************************/ - -/****************************************************************************** - * - * SkAddrInit - initialize data, set state to init - * - * Description: - * - * SK_INIT_DATA - * ============ - * - * This routine clears the multicast tables and resets promiscuous mode. - * Some entries are reserved for the "logical MAC address", the - * SK-RLMT multicast address, and the BPDU multicast address. - * - * - * SK_INIT_IO - * ========== - * - * All permanent MAC addresses are read from EPROM. - * If the current MAC addresses are not already set in software, - * they are set to the values of the permanent addresses. - * The current addresses are written to the corresponding MAC. - * - * - * SK_INIT_RUN - * =========== - * - * Nothing. - * - * Context: - * init, pageable - * - * Returns: - * SK_ADDR_SUCCESS - */ -int SkAddrInit( -SK_AC *pAC, /* the adapter context */ -SK_IOC IoC, /* I/O context */ -int Level) /* initialization level */ -{ - int j; - SK_U32 i; - SK_U8 *InAddr; - SK_U16 *OutAddr; - SK_ADDR_PORT *pAPort; - - switch (Level) { - case SK_INIT_DATA: - SK_MEMSET((char *) &pAC->Addr, (SK_U8) 0, - (SK_U16) sizeof(SK_ADDR)); - - for (i = 0; i < SK_MAX_MACS; i++) { - pAPort = &pAC->Addr.Port[i]; - pAPort->PromMode = SK_PROM_MODE_NONE; - - pAPort->FirstExactMatchRlmt = SK_ADDR_FIRST_MATCH_RLMT; - pAPort->FirstExactMatchDrv = SK_ADDR_FIRST_MATCH_DRV; - pAPort->NextExactMatchRlmt = SK_ADDR_FIRST_MATCH_RLMT; - pAPort->NextExactMatchDrv = SK_ADDR_FIRST_MATCH_DRV; - } -#ifdef xDEBUG - for (i = 0; i < SK_MAX_MACS; i++) { - if (pAC->Addr.Port[i].NextExactMatchRlmt < - SK_ADDR_FIRST_MATCH_RLMT) { - Next0[i] |= 4; - } - } -#endif /* DEBUG */ - /* pAC->Addr.InitDone = SK_INIT_DATA; */ - break; - - case SK_INIT_IO: -#ifndef SK_NO_RLMT - for (i = 0; i < SK_MAX_NETS; i++) { - pAC->Addr.Net[i].ActivePort = pAC->Rlmt.Net[i].ActivePort; - } -#endif /* !SK_NO_RLMT */ -#ifdef xDEBUG - for (i = 0; i < SK_MAX_MACS; i++) { - if (pAC->Addr.Port[i].NextExactMatchRlmt < - SK_ADDR_FIRST_MATCH_RLMT) { - Next0[i] |= 8; - } - } -#endif /* DEBUG */ - - /* Read permanent logical MAC address from Control Register File. */ - for (j = 0; j < SK_MAC_ADDR_LEN; j++) { - InAddr = (SK_U8 *) &pAC->Addr.Net[0].PermanentMacAddress.a[j]; - SK_IN8(IoC, B2_MAC_1 + j, InAddr); - } - - if (!pAC->Addr.Net[0].CurrentMacAddressSet) { - /* Set the current logical MAC address to the permanent one. */ - pAC->Addr.Net[0].CurrentMacAddress = - pAC->Addr.Net[0].PermanentMacAddress; - pAC->Addr.Net[0].CurrentMacAddressSet = SK_TRUE; - } - - /* Set the current logical MAC address. */ - pAC->Addr.Port[pAC->Addr.Net[0].ActivePort].Exact[0] = - pAC->Addr.Net[0].CurrentMacAddress; -#if SK_MAX_NETS > 1 - /* Set logical MAC address for net 2 to (log | 3). */ - if (!pAC->Addr.Net[1].CurrentMacAddressSet) { - pAC->Addr.Net[1].PermanentMacAddress = - pAC->Addr.Net[0].PermanentMacAddress; - pAC->Addr.Net[1].PermanentMacAddress.a[5] |= 3; - /* Set the current logical MAC address to the permanent one. */ - pAC->Addr.Net[1].CurrentMacAddress = - pAC->Addr.Net[1].PermanentMacAddress; - pAC->Addr.Net[1].CurrentMacAddressSet = SK_TRUE; - } -#endif /* SK_MAX_NETS > 1 */ - -#ifdef DEBUG - for (i = 0; i < (SK_U32) pAC->GIni.GIMacsFound; i++) { - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_INIT, - ("Permanent MAC Address (Net%d): %02X %02X %02X %02X %02X %02X\n", - i, - pAC->Addr.Net[i].PermanentMacAddress.a[0], - pAC->Addr.Net[i].PermanentMacAddress.a[1], - pAC->Addr.Net[i].PermanentMacAddress.a[2], - pAC->Addr.Net[i].PermanentMacAddress.a[3], - pAC->Addr.Net[i].PermanentMacAddress.a[4], - pAC->Addr.Net[i].PermanentMacAddress.a[5])) - - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_INIT, - ("Logical MAC Address (Net%d): %02X %02X %02X %02X %02X %02X\n", - i, - pAC->Addr.Net[i].CurrentMacAddress.a[0], - pAC->Addr.Net[i].CurrentMacAddress.a[1], - pAC->Addr.Net[i].CurrentMacAddress.a[2], - pAC->Addr.Net[i].CurrentMacAddress.a[3], - pAC->Addr.Net[i].CurrentMacAddress.a[4], - pAC->Addr.Net[i].CurrentMacAddress.a[5])) - } -#endif /* DEBUG */ - - for (i = 0; i < (SK_U32) pAC->GIni.GIMacsFound; i++) { - pAPort = &pAC->Addr.Port[i]; - - /* Read permanent port addresses from Control Register File. */ - for (j = 0; j < SK_MAC_ADDR_LEN; j++) { - InAddr = (SK_U8 *) &pAPort->PermanentMacAddress.a[j]; - SK_IN8(IoC, B2_MAC_2 + 8 * i + j, InAddr); - } - - if (!pAPort->CurrentMacAddressSet) { - /* - * Set the current and previous physical MAC address - * of this port to its permanent MAC address. - */ - pAPort->CurrentMacAddress = pAPort->PermanentMacAddress; - pAPort->PreviousMacAddress = pAPort->PermanentMacAddress; - pAPort->CurrentMacAddressSet = SK_TRUE; - } - - /* Set port's current physical MAC address. */ - OutAddr = (SK_U16 *) &pAPort->CurrentMacAddress.a[0]; -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - XM_OUTADDR(IoC, i, XM_SA, OutAddr); - } -#endif /* GENESIS */ -#ifdef YUKON - if (!pAC->GIni.GIGenesis) { - GM_OUTADDR(IoC, i, GM_SRC_ADDR_1L, OutAddr); - } -#endif /* YUKON */ -#ifdef DEBUG - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_INIT, - ("SkAddrInit: Permanent Physical MAC Address: %02X %02X %02X %02X %02X %02X\n", - pAPort->PermanentMacAddress.a[0], - pAPort->PermanentMacAddress.a[1], - pAPort->PermanentMacAddress.a[2], - pAPort->PermanentMacAddress.a[3], - pAPort->PermanentMacAddress.a[4], - pAPort->PermanentMacAddress.a[5])) - - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_INIT, - ("SkAddrInit: Physical MAC Address: %02X %02X %02X %02X %02X %02X\n", - pAPort->CurrentMacAddress.a[0], - pAPort->CurrentMacAddress.a[1], - pAPort->CurrentMacAddress.a[2], - pAPort->CurrentMacAddress.a[3], - pAPort->CurrentMacAddress.a[4], - pAPort->CurrentMacAddress.a[5])) -#endif /* DEBUG */ - } - /* pAC->Addr.InitDone = SK_INIT_IO; */ - break; - - case SK_INIT_RUN: -#ifdef xDEBUG - for (i = 0; i < SK_MAX_MACS; i++) { - if (pAC->Addr.Port[i].NextExactMatchRlmt < - SK_ADDR_FIRST_MATCH_RLMT) { - Next0[i] |= 16; - } - } -#endif /* DEBUG */ - - /* pAC->Addr.InitDone = SK_INIT_RUN; */ - break; - - default: /* error */ - break; - } - - return (SK_ADDR_SUCCESS); - -} /* SkAddrInit */ - -#ifndef SK_SLIM - -/****************************************************************************** - * - * SkAddrMcClear - clear the multicast table - * - * Description: - * This routine clears the multicast table. - * - * If not suppressed by Flag SK_MC_SW_ONLY, the hardware is updated - * immediately. - * - * It calls either SkAddrXmacMcClear or SkAddrGmacMcClear, according - * to the adapter in use. The real work is done there. - * - * Context: - * runtime, pageable - * may be called starting with SK_INIT_DATA with flag SK_MC_SW_ONLY - * may be called after SK_INIT_IO without limitation - * - * Returns: - * SK_ADDR_SUCCESS - * SK_ADDR_ILLEGAL_PORT - */ -int SkAddrMcClear( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* Index of affected port */ -int Flags) /* permanent/non-perm, sw-only */ -{ - int ReturnCode; - - if (PortNumber >= (SK_U32) pAC->GIni.GIMacsFound) { - return (SK_ADDR_ILLEGAL_PORT); - } - - if (pAC->GIni.GIGenesis) { - ReturnCode = SkAddrXmacMcClear(pAC, IoC, PortNumber, Flags); - } - else { - ReturnCode = SkAddrGmacMcClear(pAC, IoC, PortNumber, Flags); - } - - return (ReturnCode); - -} /* SkAddrMcClear */ - -#endif /* !SK_SLIM */ - -#ifndef SK_SLIM - -/****************************************************************************** - * - * SkAddrXmacMcClear - clear the multicast table - * - * Description: - * This routine clears the multicast table - * (either entry 2 or entries 3-16 and InexactFilter) of the given port. - * If not suppressed by Flag SK_MC_SW_ONLY, the hardware is updated - * immediately. - * - * Context: - * runtime, pageable - * may be called starting with SK_INIT_DATA with flag SK_MC_SW_ONLY - * may be called after SK_INIT_IO without limitation - * - * Returns: - * SK_ADDR_SUCCESS - * SK_ADDR_ILLEGAL_PORT - */ -static int SkAddrXmacMcClear( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* Index of affected port */ -int Flags) /* permanent/non-perm, sw-only */ -{ - int i; - - if (Flags & SK_ADDR_PERMANENT) { /* permanent => RLMT */ - - /* Clear RLMT multicast addresses. */ - pAC->Addr.Port[PortNumber].NextExactMatchRlmt = SK_ADDR_FIRST_MATCH_RLMT; - } - else { /* not permanent => DRV */ - - /* Clear InexactFilter */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] = 0; - } - - /* Clear DRV multicast addresses. */ - - pAC->Addr.Port[PortNumber].NextExactMatchDrv = SK_ADDR_FIRST_MATCH_DRV; - } - - if (!(Flags & SK_MC_SW_ONLY)) { - (void) SkAddrXmacMcUpdate(pAC, IoC, PortNumber); - } - - return (SK_ADDR_SUCCESS); - -} /* SkAddrXmacMcClear */ - -#endif /* !SK_SLIM */ - -#ifndef SK_SLIM - -/****************************************************************************** - * - * SkAddrGmacMcClear - clear the multicast table - * - * Description: - * This routine clears the multicast hashing table (InexactFilter) - * (either the RLMT or the driver bits) of the given port. - * - * If not suppressed by Flag SK_MC_SW_ONLY, the hardware is updated - * immediately. - * - * Context: - * runtime, pageable - * may be called starting with SK_INIT_DATA with flag SK_MC_SW_ONLY - * may be called after SK_INIT_IO without limitation - * - * Returns: - * SK_ADDR_SUCCESS - * SK_ADDR_ILLEGAL_PORT - */ -static int SkAddrGmacMcClear( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* Index of affected port */ -int Flags) /* permanent/non-perm, sw-only */ -{ - int i; - -#ifdef DEBUG - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("GMAC InexactFilter (not cleared): %02X %02X %02X %02X %02X %02X %02X %02X\n", - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[0], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[1], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[2], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[3], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[4], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[5], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[6], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[7])) -#endif /* DEBUG */ - - /* Clear InexactFilter */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] = 0; - } - - if (Flags & SK_ADDR_PERMANENT) { /* permanent => RLMT */ - - /* Copy DRV bits to InexactFilter. */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] |= - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[i]; - - /* Clear InexactRlmtFilter. */ - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[i] = 0; - - } - } - else { /* not permanent => DRV */ - - /* Copy RLMT bits to InexactFilter. */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] |= - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[i]; - - /* Clear InexactDrvFilter. */ - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[i] = 0; - } - } - -#ifdef DEBUG - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("GMAC InexactFilter (cleared): %02X %02X %02X %02X %02X %02X %02X %02X\n", - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[0], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[1], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[2], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[3], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[4], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[5], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[6], - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[7])) -#endif /* DEBUG */ - - if (!(Flags & SK_MC_SW_ONLY)) { - (void) SkAddrGmacMcUpdate(pAC, IoC, PortNumber); - } - - return (SK_ADDR_SUCCESS); - -} /* SkAddrGmacMcClear */ - -#ifndef SK_ADDR_CHEAT - -/****************************************************************************** - * - * SkXmacMcHash - hash multicast address - * - * Description: - * This routine computes the hash value for a multicast address. - * A CRC32 algorithm is used. - * - * Notes: - * The code was adapted from the XaQti data sheet. - * - * Context: - * runtime, pageable - * - * Returns: - * Hash value of multicast address. - */ -static SK_U32 SkXmacMcHash( -unsigned char *pMc) /* Multicast address */ -{ - SK_U32 Idx; - SK_U32 Bit; - SK_U32 Data; - SK_U32 Crc; - - Crc = 0xFFFFFFFFUL; - for (Idx = 0; Idx < SK_MAC_ADDR_LEN; Idx++) { - Data = *pMc++; - for (Bit = 0; Bit < 8; Bit++, Data >>= 1) { - Crc = (Crc >> 1) ^ (((Crc ^ Data) & 1) ? XMAC_POLY : 0); - } - } - - return (Crc & ((1 << HASH_BITS) - 1)); - -} /* SkXmacMcHash */ - - -/****************************************************************************** - * - * SkGmacMcHash - hash multicast address - * - * Description: - * This routine computes the hash value for a multicast address. - * A CRC16 algorithm is used. - * - * Notes: - * - * - * Context: - * runtime, pageable - * - * Returns: - * Hash value of multicast address. - */ -static SK_U32 SkGmacMcHash( -unsigned char *pMc) /* Multicast address */ -{ - SK_U32 Data; - SK_U32 TmpData; - SK_U32 Crc; - int Byte; - int Bit; - - Crc = 0xFFFFFFFFUL; - for (Byte = 0; Byte < 6; Byte++) { - /* Get next byte. */ - Data = (SK_U32) pMc[Byte]; - - /* Change bit order in byte. */ - TmpData = Data; - for (Bit = 0; Bit < 8; Bit++) { - if (TmpData & 1L) { - Data |= 1L << (7 - Bit); - } - else { - Data &= ~(1L << (7 - Bit)); - } - TmpData >>= 1; - } - - Crc ^= (Data << 24); - for (Bit = 0; Bit < 8; Bit++) { - if (Crc & 0x80000000) { - Crc = (Crc << 1) ^ GMAC_POLY; - } - else { - Crc <<= 1; - } - } - } - - return (Crc & ((1 << HASH_BITS) - 1)); - -} /* SkGmacMcHash */ - -#endif /* !SK_ADDR_CHEAT */ - -/****************************************************************************** - * - * SkAddrMcAdd - add a multicast address to a port - * - * Description: - * This routine enables reception for a given address on the given port. - * - * It calls either SkAddrXmacMcAdd or SkAddrGmacMcAdd, according to the - * adapter in use. The real work is done there. - * - * Notes: - * The return code is only valid for SK_PROM_MODE_NONE. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_DATA - * - * Returns: - * SK_MC_FILTERING_EXACT - * SK_MC_FILTERING_INEXACT - * SK_MC_ILLEGAL_ADDRESS - * SK_MC_ILLEGAL_PORT - * SK_MC_RLMT_OVERFLOW - */ -int SkAddrMcAdd( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* Port Number */ -SK_MAC_ADDR *pMc, /* multicast address to be added */ -int Flags) /* permanent/non-permanent */ -{ - int ReturnCode; - - if (PortNumber >= (SK_U32) pAC->GIni.GIMacsFound) { - return (SK_ADDR_ILLEGAL_PORT); - } - - if (pAC->GIni.GIGenesis) { - ReturnCode = SkAddrXmacMcAdd(pAC, IoC, PortNumber, pMc, Flags); - } - else { - ReturnCode = SkAddrGmacMcAdd(pAC, IoC, PortNumber, pMc, Flags); - } - - return (ReturnCode); - -} /* SkAddrMcAdd */ - - -/****************************************************************************** - * - * SkAddrXmacMcAdd - add a multicast address to a port - * - * Description: - * This routine enables reception for a given address on the given port. - * - * Notes: - * The return code is only valid for SK_PROM_MODE_NONE. - * - * The multicast bit is only checked if there are no free exact match - * entries. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_DATA - * - * Returns: - * SK_MC_FILTERING_EXACT - * SK_MC_FILTERING_INEXACT - * SK_MC_ILLEGAL_ADDRESS - * SK_MC_RLMT_OVERFLOW - */ -static int SkAddrXmacMcAdd( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* Port Number */ -SK_MAC_ADDR *pMc, /* multicast address to be added */ -int Flags) /* permanent/non-permanent */ -{ - int i; - SK_U8 Inexact; -#ifndef SK_ADDR_CHEAT - SK_U32 HashBit; -#endif /* !defined(SK_ADDR_CHEAT) */ - - if (Flags & SK_ADDR_PERMANENT) { /* permanent => RLMT */ -#ifdef xDEBUG - if (pAC->Addr.Port[PortNumber].NextExactMatchRlmt < - SK_ADDR_FIRST_MATCH_RLMT) { - Next0[PortNumber] |= 1; - return (SK_MC_RLMT_OVERFLOW); - } -#endif /* DEBUG */ - - if (pAC->Addr.Port[PortNumber].NextExactMatchRlmt > - SK_ADDR_LAST_MATCH_RLMT) { - return (SK_MC_RLMT_OVERFLOW); - } - - /* Set a RLMT multicast address. */ - - pAC->Addr.Port[PortNumber].Exact[ - pAC->Addr.Port[PortNumber].NextExactMatchRlmt++] = *pMc; - - return (SK_MC_FILTERING_EXACT); - } - -#ifdef xDEBUG - if (pAC->Addr.Port[PortNumber].NextExactMatchDrv < - SK_ADDR_FIRST_MATCH_DRV) { - Next0[PortNumber] |= 2; - return (SK_MC_RLMT_OVERFLOW); - } -#endif /* DEBUG */ - - if (pAC->Addr.Port[PortNumber].NextExactMatchDrv <= SK_ADDR_LAST_MATCH_DRV) { - - /* Set exact match entry. */ - pAC->Addr.Port[PortNumber].Exact[ - pAC->Addr.Port[PortNumber].NextExactMatchDrv++] = *pMc; - - /* Clear InexactFilter */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] = 0; - } - } - else { - if (!(pMc->a[0] & SK_MC_BIT)) { - /* Hashing only possible with multicast addresses */ - return (SK_MC_ILLEGAL_ADDRESS); - } -#ifndef SK_ADDR_CHEAT - /* Compute hash value of address. */ - HashBit = 63 - SkXmacMcHash(&pMc->a[0]); - - /* Add bit to InexactFilter. */ - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[HashBit / 8] |= - 1 << (HashBit % 8); -#else /* SK_ADDR_CHEAT */ - /* Set all bits in InexactFilter. */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] = 0xFF; - } -#endif /* SK_ADDR_CHEAT */ - } - - for (Inexact = 0, i = 0; i < 8; i++) { - Inexact |= pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i]; - } - - if (Inexact == 0 && pAC->Addr.Port[PortNumber].PromMode == 0) { - return (SK_MC_FILTERING_EXACT); - } - else { - return (SK_MC_FILTERING_INEXACT); - } - -} /* SkAddrXmacMcAdd */ - - -/****************************************************************************** - * - * SkAddrGmacMcAdd - add a multicast address to a port - * - * Description: - * This routine enables reception for a given address on the given port. - * - * Notes: - * The return code is only valid for SK_PROM_MODE_NONE. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_DATA - * - * Returns: - * SK_MC_FILTERING_INEXACT - * SK_MC_ILLEGAL_ADDRESS - */ -static int SkAddrGmacMcAdd( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* Port Number */ -SK_MAC_ADDR *pMc, /* multicast address to be added */ -int Flags) /* permanent/non-permanent */ -{ - int i; -#ifndef SK_ADDR_CHEAT - SK_U32 HashBit; -#endif /* !defined(SK_ADDR_CHEAT) */ - - if (!(pMc->a[0] & SK_MC_BIT)) { - /* Hashing only possible with multicast addresses */ - return (SK_MC_ILLEGAL_ADDRESS); - } - -#ifndef SK_ADDR_CHEAT - - /* Compute hash value of address. */ - HashBit = SkGmacMcHash(&pMc->a[0]); - - if (Flags & SK_ADDR_PERMANENT) { /* permanent => RLMT */ - - /* Add bit to InexactRlmtFilter. */ - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[HashBit / 8] |= - 1 << (HashBit % 8); - - /* Copy bit to InexactFilter. */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] |= - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[i]; - } -#ifdef DEBUG - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("GMAC InexactRlmtFilter: %02X %02X %02X %02X %02X %02X %02X %02X\n", - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[0], - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[1], - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[2], - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[3], - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[4], - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[5], - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[6], - pAC->Addr.Port[PortNumber].InexactRlmtFilter.Bytes[7])) -#endif /* DEBUG */ - } - else { /* not permanent => DRV */ - - /* Add bit to InexactDrvFilter. */ - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[HashBit / 8] |= - 1 << (HashBit % 8); - - /* Copy bit to InexactFilter. */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] |= - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[i]; - } -#ifdef DEBUG - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("GMAC InexactDrvFilter: %02X %02X %02X %02X %02X %02X %02X %02X\n", - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[0], - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[1], - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[2], - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[3], - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[4], - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[5], - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[6], - pAC->Addr.Port[PortNumber].InexactDrvFilter.Bytes[7])) -#endif /* DEBUG */ - } - -#else /* SK_ADDR_CHEAT */ - - /* Set all bits in InexactFilter. */ - for (i = 0; i < 8; i++) { - pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i] = 0xFF; - } -#endif /* SK_ADDR_CHEAT */ - - return (SK_MC_FILTERING_INEXACT); - -} /* SkAddrGmacMcAdd */ - -#endif /* !SK_SLIM */ - -/****************************************************************************** - * - * SkAddrMcUpdate - update the HW MC address table and set the MAC address - * - * Description: - * This routine enables reception of the addresses contained in a local - * table for a given port. - * It also programs the port's current physical MAC address. - * - * It calls either SkAddrXmacMcUpdate or SkAddrGmacMcUpdate, according - * to the adapter in use. The real work is done there. - * - * Notes: - * The return code is only valid for SK_PROM_MODE_NONE. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_IO - * - * Returns: - * SK_MC_FILTERING_EXACT - * SK_MC_FILTERING_INEXACT - * SK_ADDR_ILLEGAL_PORT - */ -int SkAddrMcUpdate( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber) /* Port Number */ -{ - int ReturnCode = 0; -#if (!defined(SK_SLIM) || defined(DEBUG)) - if (PortNumber >= (SK_U32) pAC->GIni.GIMacsFound) { - return (SK_ADDR_ILLEGAL_PORT); - } -#endif /* !SK_SLIM || DEBUG */ - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - ReturnCode = SkAddrXmacMcUpdate(pAC, IoC, PortNumber); - } -#endif /* GENESIS */ -#ifdef YUKON - if (!pAC->GIni.GIGenesis) { - ReturnCode = SkAddrGmacMcUpdate(pAC, IoC, PortNumber); - } -#endif /* YUKON */ - return (ReturnCode); - -} /* SkAddrMcUpdate */ - - -#ifdef GENESIS - -/****************************************************************************** - * - * SkAddrXmacMcUpdate - update the HW MC address table and set the MAC address - * - * Description: - * This routine enables reception of the addresses contained in a local - * table for a given port. - * It also programs the port's current physical MAC address. - * - * Notes: - * The return code is only valid for SK_PROM_MODE_NONE. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_IO - * - * Returns: - * SK_MC_FILTERING_EXACT - * SK_MC_FILTERING_INEXACT - * SK_ADDR_ILLEGAL_PORT - */ -static int SkAddrXmacMcUpdate( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber) /* Port Number */ -{ - SK_U32 i; - SK_U8 Inexact; - SK_U16 *OutAddr; - SK_ADDR_PORT *pAPort; - - SK_DBG_MSG(pAC,SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("SkAddrXmacMcUpdate on Port %u.\n", PortNumber)) - - pAPort = &pAC->Addr.Port[PortNumber]; - -#ifdef DEBUG - SK_DBG_MSG(pAC,SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("Next0 on Port %d: %d\n", PortNumber, Next0[PortNumber])) -#endif /* DEBUG */ - - /* Start with 0 to also program the logical MAC address. */ - for (i = 0; i < pAPort->NextExactMatchRlmt; i++) { - /* Set exact match address i on XMAC */ - OutAddr = (SK_U16 *) &pAPort->Exact[i].a[0]; - XM_OUTADDR(IoC, PortNumber, XM_EXM(i), OutAddr); - } - - /* Clear other permanent exact match addresses on XMAC */ - if (pAPort->NextExactMatchRlmt <= SK_ADDR_LAST_MATCH_RLMT) { - - SkXmClrExactAddr(pAC, IoC, PortNumber, pAPort->NextExactMatchRlmt, - SK_ADDR_LAST_MATCH_RLMT); - } - - for (i = pAPort->FirstExactMatchDrv; i < pAPort->NextExactMatchDrv; i++) { - OutAddr = (SK_U16 *) &pAPort->Exact[i].a[0]; - XM_OUTADDR(IoC, PortNumber, XM_EXM(i), OutAddr); - } - - /* Clear other non-permanent exact match addresses on XMAC */ - if (pAPort->NextExactMatchDrv <= SK_ADDR_LAST_MATCH_DRV) { - - SkXmClrExactAddr(pAC, IoC, PortNumber, pAPort->NextExactMatchDrv, - SK_ADDR_LAST_MATCH_DRV); - } - - for (Inexact = 0, i = 0; i < 8; i++) { - Inexact |= pAPort->InexactFilter.Bytes[i]; - } - - if (pAPort->PromMode & SK_PROM_MODE_ALL_MC) { - - /* Set all bits in 64-bit hash register. */ - XM_OUTHASH(IoC, PortNumber, XM_HSM, &OnesHash); - - /* Enable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - } - else if (Inexact != 0) { - - /* Set 64-bit hash register to InexactFilter. */ - XM_OUTHASH(IoC, PortNumber, XM_HSM, &pAPort->InexactFilter.Bytes[0]); - - /* Enable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - } - else { - /* Disable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_FALSE); - } - - if (pAPort->PromMode != SK_PROM_MODE_NONE) { - (void) SkAddrXmacPromiscuousChange(pAC, IoC, PortNumber, pAPort->PromMode); - } - - /* Set port's current physical MAC address. */ - OutAddr = (SK_U16 *) &pAPort->CurrentMacAddress.a[0]; - - XM_OUTADDR(IoC, PortNumber, XM_SA, OutAddr); - -#ifdef xDEBUG - for (i = 0; i < pAPort->NextExactMatchRlmt; i++) { - SK_U8 InAddr8[6]; - SK_U16 *InAddr; - - /* Get exact match address i from port PortNumber. */ - InAddr = (SK_U16 *) &InAddr8[0]; - - XM_INADDR(IoC, PortNumber, XM_EXM(i), InAddr); - - SK_DBG_MSG(pAC,SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("SkAddrXmacMcUpdate: MC address %d on Port %u: ", - "%02x %02x %02x %02x %02x %02x -- %02x %02x %02x %02x %02x %02x\n", - i, - PortNumber, - InAddr8[0], - InAddr8[1], - InAddr8[2], - InAddr8[3], - InAddr8[4], - InAddr8[5], - pAPort->Exact[i].a[0], - pAPort->Exact[i].a[1], - pAPort->Exact[i].a[2], - pAPort->Exact[i].a[3], - pAPort->Exact[i].a[4], - pAPort->Exact[i].a[5])) - } -#endif /* DEBUG */ - - /* Determine return value. */ - if (Inexact == 0 && pAPort->PromMode == 0) { - return (SK_MC_FILTERING_EXACT); - } - else { - return (SK_MC_FILTERING_INEXACT); - } - -} /* SkAddrXmacMcUpdate */ - -#endif /* GENESIS */ - -#ifdef YUKON - -/****************************************************************************** - * - * SkAddrGmacMcUpdate - update the HW MC address table and set the MAC address - * - * Description: - * This routine enables reception of the addresses contained in a local - * table for a given port. - * It also programs the port's current physical MAC address. - * - * Notes: - * The return code is only valid for SK_PROM_MODE_NONE. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_IO - * - * Returns: - * SK_MC_FILTERING_EXACT - * SK_MC_FILTERING_INEXACT - * SK_ADDR_ILLEGAL_PORT - */ -static int SkAddrGmacMcUpdate( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber) /* Port Number */ -{ -#ifndef SK_SLIM - SK_U32 i; - SK_U8 Inexact; -#endif /* not SK_SLIM */ - SK_U16 *OutAddr; - SK_ADDR_PORT *pAPort; - - SK_DBG_MSG(pAC,SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("SkAddrGmacMcUpdate on Port %u.\n", PortNumber)) - - pAPort = &pAC->Addr.Port[PortNumber]; - -#ifdef DEBUG - SK_DBG_MSG(pAC,SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("Next0 on Port %d: %d\n", PortNumber, Next0[PortNumber])) -#endif /* DEBUG */ - -#ifndef SK_SLIM - for (Inexact = 0, i = 0; i < 8; i++) { - Inexact |= pAPort->InexactFilter.Bytes[i]; - } - - /* Set 64-bit hash register to InexactFilter. */ - GM_OUTHASH(IoC, PortNumber, GM_MC_ADDR_H1, - &pAPort->InexactFilter.Bytes[0]); - - if (pAPort->PromMode & SK_PROM_MODE_ALL_MC) { - - /* Set all bits in 64-bit hash register. */ - GM_OUTHASH(IoC, PortNumber, GM_MC_ADDR_H1, &OnesHash); - - /* Enable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - } - else { - /* Enable Hashing. */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - } - - if (pAPort->PromMode != SK_PROM_MODE_NONE) { - (void) SkAddrGmacPromiscuousChange(pAC, IoC, PortNumber, pAPort->PromMode); - } -#else /* SK_SLIM */ - - /* Set all bits in 64-bit hash register. */ - GM_OUTHASH(IoC, PortNumber, GM_MC_ADDR_H1, &OnesHash); - - /* Enable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - - (void) SkAddrGmacPromiscuousChange(pAC, IoC, PortNumber, pAPort->PromMode); - -#endif /* SK_SLIM */ - - /* Set port's current physical MAC address. */ - OutAddr = (SK_U16 *) &pAPort->CurrentMacAddress.a[0]; - GM_OUTADDR(IoC, PortNumber, GM_SRC_ADDR_1L, OutAddr); - - /* Set port's current logical MAC address. */ - OutAddr = (SK_U16 *) &pAPort->Exact[0].a[0]; - GM_OUTADDR(IoC, PortNumber, GM_SRC_ADDR_2L, OutAddr); - -#ifdef DEBUG - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("SkAddrGmacMcUpdate: Permanent Physical MAC Address: %02X %02X %02X %02X %02X %02X\n", - pAPort->Exact[0].a[0], - pAPort->Exact[0].a[1], - pAPort->Exact[0].a[2], - pAPort->Exact[0].a[3], - pAPort->Exact[0].a[4], - pAPort->Exact[0].a[5])) - - SK_DBG_MSG(pAC, SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("SkAddrGmacMcUpdate: Physical MAC Address: %02X %02X %02X %02X %02X %02X\n", - pAPort->CurrentMacAddress.a[0], - pAPort->CurrentMacAddress.a[1], - pAPort->CurrentMacAddress.a[2], - pAPort->CurrentMacAddress.a[3], - pAPort->CurrentMacAddress.a[4], - pAPort->CurrentMacAddress.a[5])) -#endif /* DEBUG */ - -#ifndef SK_SLIM - /* Determine return value. */ - if (Inexact == 0 && pAPort->PromMode == 0) { - return (SK_MC_FILTERING_EXACT); - } - else { - return (SK_MC_FILTERING_INEXACT); - } -#else /* SK_SLIM */ - return (SK_MC_FILTERING_INEXACT); -#endif /* SK_SLIM */ - -} /* SkAddrGmacMcUpdate */ - -#endif /* YUKON */ - -#ifndef SK_NO_MAO - -/****************************************************************************** - * - * SkAddrOverride - override a port's MAC address - * - * Description: - * This routine overrides the MAC address of one port. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_IO - * - * Returns: - * SK_ADDR_SUCCESS if successful. - * SK_ADDR_DUPLICATE_ADDRESS if duplicate MAC address. - * SK_ADDR_MULTICAST_ADDRESS if multicast or broadcast address. - * SK_ADDR_TOO_EARLY if SK_INIT_IO was not executed before. - */ -int SkAddrOverride( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* Port Number */ -SK_MAC_ADDR SK_FAR *pNewAddr, /* new MAC address */ -int Flags) /* logical/physical MAC address */ -{ -#ifndef SK_NO_RLMT - SK_EVPARA Para; -#endif /* !SK_NO_RLMT */ - SK_U32 NetNumber; - SK_U32 i; - SK_U16 SK_FAR *OutAddr; - -#ifndef SK_NO_RLMT - NetNumber = pAC->Rlmt.Port[PortNumber].Net->NetNumber; -#else - NetNumber = 0; -#endif /* SK_NO_RLMT */ -#if (!defined(SK_SLIM) || defined(DEBUG)) - if (PortNumber >= (SK_U32) pAC->GIni.GIMacsFound) { - return (SK_ADDR_ILLEGAL_PORT); - } -#endif /* !SK_SLIM || DEBUG */ - if (pNewAddr != NULL && (pNewAddr->a[0] & SK_MC_BIT) != 0) { - return (SK_ADDR_MULTICAST_ADDRESS); - } - - if (!pAC->Addr.Net[NetNumber].CurrentMacAddressSet) { - return (SK_ADDR_TOO_EARLY); - } - - if (Flags & SK_ADDR_SET_LOGICAL) { /* Activate logical MAC address. */ - /* Parameter *pNewAddr is ignored. */ - for (i = 0; i < (SK_U32) pAC->GIni.GIMacsFound; i++) { - if (!pAC->Addr.Port[i].CurrentMacAddressSet) { - return (SK_ADDR_TOO_EARLY); - } - } -#ifndef SK_NO_RLMT - /* Set PortNumber to number of net's active port. */ - PortNumber = pAC->Rlmt.Net[NetNumber]. - Port[pAC->Addr.Net[NetNumber].ActivePort]->PortNumber; -#endif /* !SK_NO_RLMT */ - pAC->Addr.Port[PortNumber].Exact[0] = - pAC->Addr.Net[NetNumber].CurrentMacAddress; - - /* Write address to first exact match entry of active port. */ - (void) SkAddrMcUpdate(pAC, IoC, PortNumber); - } - else if (Flags & SK_ADDR_CLEAR_LOGICAL) { - /* Deactivate logical MAC address. */ - /* Parameter *pNewAddr is ignored. */ - for (i = 0; i < (SK_U32) pAC->GIni.GIMacsFound; i++) { - if (!pAC->Addr.Port[i].CurrentMacAddressSet) { - return (SK_ADDR_TOO_EARLY); - } - } -#ifndef SK_NO_RLMT - /* Set PortNumber to number of net's active port. */ - PortNumber = pAC->Rlmt.Net[NetNumber]. - Port[pAC->Addr.Net[NetNumber].ActivePort]->PortNumber; -#endif /* !SK_NO_RLMT */ - for (i = 0; i < SK_MAC_ADDR_LEN; i++ ) { - pAC->Addr.Port[PortNumber].Exact[0].a[i] = 0; - } - - /* Write address to first exact match entry of active port. */ - (void) SkAddrMcUpdate(pAC, IoC, PortNumber); - } - else if (Flags & SK_ADDR_PHYSICAL_ADDRESS) { /* Physical MAC address. */ - if (SK_ADDR_EQUAL(pNewAddr->a, - pAC->Addr.Net[NetNumber].CurrentMacAddress.a)) { - return (SK_ADDR_DUPLICATE_ADDRESS); - } - - for (i = 0; i < (SK_U32) pAC->GIni.GIMacsFound; i++) { - if (!pAC->Addr.Port[i].CurrentMacAddressSet) { - return (SK_ADDR_TOO_EARLY); - } - - if (SK_ADDR_EQUAL(pNewAddr->a, - pAC->Addr.Port[i].CurrentMacAddress.a)) { - if (i == PortNumber) { - return (SK_ADDR_SUCCESS); - } - else { - return (SK_ADDR_DUPLICATE_ADDRESS); - } - } - } - - pAC->Addr.Port[PortNumber].PreviousMacAddress = - pAC->Addr.Port[PortNumber].CurrentMacAddress; - pAC->Addr.Port[PortNumber].CurrentMacAddress = *pNewAddr; - - /* Change port's physical MAC address. */ - OutAddr = (SK_U16 SK_FAR *) pNewAddr; -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - XM_OUTADDR(IoC, PortNumber, XM_SA, OutAddr); - } -#endif /* GENESIS */ -#ifdef YUKON - if (!pAC->GIni.GIGenesis) { - GM_OUTADDR(IoC, PortNumber, GM_SRC_ADDR_1L, OutAddr); - } -#endif /* YUKON */ - -#ifndef SK_NO_RLMT - /* Report address change to RLMT. */ - Para.Para32[0] = PortNumber; - Para.Para32[0] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_PORT_ADDR, Para); -#endif /* !SK_NO_RLMT */ - } - else { /* Logical MAC address. */ - if (SK_ADDR_EQUAL(pNewAddr->a, - pAC->Addr.Net[NetNumber].CurrentMacAddress.a)) { - return (SK_ADDR_SUCCESS); - } - - for (i = 0; i < (SK_U32) pAC->GIni.GIMacsFound; i++) { - if (!pAC->Addr.Port[i].CurrentMacAddressSet) { - return (SK_ADDR_TOO_EARLY); - } - - if (SK_ADDR_EQUAL(pNewAddr->a, - pAC->Addr.Port[i].CurrentMacAddress.a)) { - return (SK_ADDR_DUPLICATE_ADDRESS); - } - } - - /* - * In case that the physical and the logical MAC addresses are equal - * we must also change the physical MAC address here. - * In this case we have an adapter which initially was programmed with - * two identical MAC addresses. - */ - if (SK_ADDR_EQUAL(pAC->Addr.Port[PortNumber].CurrentMacAddress.a, - pAC->Addr.Port[PortNumber].Exact[0].a)) { - - pAC->Addr.Port[PortNumber].PreviousMacAddress = - pAC->Addr.Port[PortNumber].CurrentMacAddress; - pAC->Addr.Port[PortNumber].CurrentMacAddress = *pNewAddr; - -#ifndef SK_NO_RLMT - /* Report address change to RLMT. */ - Para.Para32[0] = PortNumber; - Para.Para32[0] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_PORT_ADDR, Para); -#endif /* !SK_NO_RLMT */ - } - -#ifndef SK_NO_RLMT - /* Set PortNumber to number of net's active port. */ - PortNumber = pAC->Rlmt.Net[NetNumber]. - Port[pAC->Addr.Net[NetNumber].ActivePort]->PortNumber; -#endif /* !SK_NO_RLMT */ - pAC->Addr.Net[NetNumber].CurrentMacAddress = *pNewAddr; - pAC->Addr.Port[PortNumber].Exact[0] = *pNewAddr; -#ifdef DEBUG - SK_DBG_MSG(pAC,SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("SkAddrOverride: Permanent MAC Address: %02X %02X %02X %02X %02X %02X\n", - pAC->Addr.Net[NetNumber].PermanentMacAddress.a[0], - pAC->Addr.Net[NetNumber].PermanentMacAddress.a[1], - pAC->Addr.Net[NetNumber].PermanentMacAddress.a[2], - pAC->Addr.Net[NetNumber].PermanentMacAddress.a[3], - pAC->Addr.Net[NetNumber].PermanentMacAddress.a[4], - pAC->Addr.Net[NetNumber].PermanentMacAddress.a[5])) - - SK_DBG_MSG(pAC,SK_DBGMOD_ADDR, SK_DBGCAT_CTRL, - ("SkAddrOverride: New logical MAC Address: %02X %02X %02X %02X %02X %02X\n", - pAC->Addr.Net[NetNumber].CurrentMacAddress.a[0], - pAC->Addr.Net[NetNumber].CurrentMacAddress.a[1], - pAC->Addr.Net[NetNumber].CurrentMacAddress.a[2], - pAC->Addr.Net[NetNumber].CurrentMacAddress.a[3], - pAC->Addr.Net[NetNumber].CurrentMacAddress.a[4], - pAC->Addr.Net[NetNumber].CurrentMacAddress.a[5])) -#endif /* DEBUG */ - - /* Write address to first exact match entry of active port. */ - (void) SkAddrMcUpdate(pAC, IoC, PortNumber); - } - - return (SK_ADDR_SUCCESS); - -} /* SkAddrOverride */ - - -#endif /* SK_NO_MAO */ - -/****************************************************************************** - * - * SkAddrPromiscuousChange - set promiscuous mode for given port - * - * Description: - * This routine manages promiscuous mode: - * - none - * - all LLC frames - * - all MC frames - * - * It calls either SkAddrXmacPromiscuousChange or - * SkAddrGmacPromiscuousChange, according to the adapter in use. - * The real work is done there. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_IO - * - * Returns: - * SK_ADDR_SUCCESS - * SK_ADDR_ILLEGAL_PORT - */ -int SkAddrPromiscuousChange( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* port whose promiscuous mode changes */ -int NewPromMode) /* new promiscuous mode */ -{ - int ReturnCode = 0; -#if (!defined(SK_SLIM) || defined(DEBUG)) - if (PortNumber >= (SK_U32) pAC->GIni.GIMacsFound) { - return (SK_ADDR_ILLEGAL_PORT); - } -#endif /* !SK_SLIM || DEBUG */ - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - ReturnCode = - SkAddrXmacPromiscuousChange(pAC, IoC, PortNumber, NewPromMode); - } -#endif /* GENESIS */ -#ifdef YUKON - if (!pAC->GIni.GIGenesis) { - ReturnCode = - SkAddrGmacPromiscuousChange(pAC, IoC, PortNumber, NewPromMode); - } -#endif /* YUKON */ - - return (ReturnCode); - -} /* SkAddrPromiscuousChange */ - -#ifdef GENESIS - -/****************************************************************************** - * - * SkAddrXmacPromiscuousChange - set promiscuous mode for given port - * - * Description: - * This routine manages promiscuous mode: - * - none - * - all LLC frames - * - all MC frames - * - * Context: - * runtime, pageable - * may be called after SK_INIT_IO - * - * Returns: - * SK_ADDR_SUCCESS - * SK_ADDR_ILLEGAL_PORT - */ -static int SkAddrXmacPromiscuousChange( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* port whose promiscuous mode changes */ -int NewPromMode) /* new promiscuous mode */ -{ - int i; - SK_BOOL InexactModeBit; - SK_U8 Inexact; - SK_U8 HwInexact; - SK_FILTER64 HwInexactFilter; - SK_U16 LoMode; /* Lower 16 bits of XMAC Mode Register. */ - int CurPromMode = SK_PROM_MODE_NONE; - - /* Read CurPromMode from Hardware. */ - XM_IN16(IoC, PortNumber, XM_MODE, &LoMode); - - if ((LoMode & XM_MD_ENA_PROM) != 0) { - /* Promiscuous mode! */ - CurPromMode |= SK_PROM_MODE_LLC; - } - - for (Inexact = 0xFF, i = 0; i < 8; i++) { - Inexact &= pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i]; - } - if (Inexact == 0xFF) { - CurPromMode |= (pAC->Addr.Port[PortNumber].PromMode & SK_PROM_MODE_ALL_MC); - } - else { - /* Get InexactModeBit (bit XM_MD_ENA_HASH in mode register) */ - XM_IN16(IoC, PortNumber, XM_MODE, &LoMode); - - InexactModeBit = (LoMode & XM_MD_ENA_HASH) != 0; - - /* Read 64-bit hash register from XMAC */ - XM_INHASH(IoC, PortNumber, XM_HSM, &HwInexactFilter.Bytes[0]); - - for (HwInexact = 0xFF, i = 0; i < 8; i++) { - HwInexact &= HwInexactFilter.Bytes[i]; - } - - if (InexactModeBit && (HwInexact == 0xFF)) { - CurPromMode |= SK_PROM_MODE_ALL_MC; - } - } - - pAC->Addr.Port[PortNumber].PromMode = NewPromMode; - - if (NewPromMode == CurPromMode) { - return (SK_ADDR_SUCCESS); - } - - if ((NewPromMode & SK_PROM_MODE_ALL_MC) && - !(CurPromMode & SK_PROM_MODE_ALL_MC)) { /* All MC. */ - - /* Set all bits in 64-bit hash register. */ - XM_OUTHASH(IoC, PortNumber, XM_HSM, &OnesHash); - - /* Enable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - } - else if ((CurPromMode & SK_PROM_MODE_ALL_MC) && - !(NewPromMode & SK_PROM_MODE_ALL_MC)) { /* Norm MC. */ - for (Inexact = 0, i = 0; i < 8; i++) { - Inexact |= pAC->Addr.Port[PortNumber].InexactFilter.Bytes[i]; - } - if (Inexact == 0) { - /* Disable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_FALSE); - } - else { - /* Set 64-bit hash register to InexactFilter. */ - XM_OUTHASH(IoC, PortNumber, XM_HSM, - &pAC->Addr.Port[PortNumber].InexactFilter.Bytes[0]); - - /* Enable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - } - } - - if ((NewPromMode & SK_PROM_MODE_LLC) && - !(CurPromMode & SK_PROM_MODE_LLC)) { /* Prom. LLC */ - /* Set the MAC in Promiscuous Mode */ - SkMacPromiscMode(pAC, IoC, (int) PortNumber, SK_TRUE); - } - else if ((CurPromMode & SK_PROM_MODE_LLC) && - !(NewPromMode & SK_PROM_MODE_LLC)) { /* Norm. LLC. */ - /* Clear Promiscuous Mode */ - SkMacPromiscMode(pAC, IoC, (int) PortNumber, SK_FALSE); - } - - return (SK_ADDR_SUCCESS); - -} /* SkAddrXmacPromiscuousChange */ - -#endif /* GENESIS */ - -#ifdef YUKON - -/****************************************************************************** - * - * SkAddrGmacPromiscuousChange - set promiscuous mode for given port - * - * Description: - * This routine manages promiscuous mode: - * - none - * - all LLC frames - * - all MC frames - * - * Context: - * runtime, pageable - * may be called after SK_INIT_IO - * - * Returns: - * SK_ADDR_SUCCESS - * SK_ADDR_ILLEGAL_PORT - */ -static int SkAddrGmacPromiscuousChange( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 PortNumber, /* port whose promiscuous mode changes */ -int NewPromMode) /* new promiscuous mode */ -{ - SK_U16 ReceiveControl; /* GMAC Receive Control Register */ - int CurPromMode = SK_PROM_MODE_NONE; - - /* Read CurPromMode from Hardware. */ - GM_IN16(IoC, PortNumber, GM_RX_CTRL, &ReceiveControl); - - if ((ReceiveControl & (GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA)) == 0) { - /* Promiscuous mode! */ - CurPromMode |= SK_PROM_MODE_LLC; - } - - if ((ReceiveControl & GM_RXCR_MCF_ENA) == 0) { - /* All Multicast mode! */ - CurPromMode |= (pAC->Addr.Port[PortNumber].PromMode & SK_PROM_MODE_ALL_MC); - } - - pAC->Addr.Port[PortNumber].PromMode = NewPromMode; - - if (NewPromMode == CurPromMode) { - return (SK_ADDR_SUCCESS); - } - - if ((NewPromMode & SK_PROM_MODE_ALL_MC) && - !(CurPromMode & SK_PROM_MODE_ALL_MC)) { /* All MC */ - - /* Set all bits in 64-bit hash register. */ - GM_OUTHASH(IoC, PortNumber, GM_MC_ADDR_H1, &OnesHash); - - /* Enable Hashing */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - } - - if ((CurPromMode & SK_PROM_MODE_ALL_MC) && - !(NewPromMode & SK_PROM_MODE_ALL_MC)) { /* Norm. MC */ - - /* Set 64-bit hash register to InexactFilter. */ - GM_OUTHASH(IoC, PortNumber, GM_MC_ADDR_H1, - &pAC->Addr.Port[PortNumber].InexactFilter.Bytes[0]); - - /* Enable Hashing. */ - SkMacHashing(pAC, IoC, (int) PortNumber, SK_TRUE); - } - - if ((NewPromMode & SK_PROM_MODE_LLC) && - !(CurPromMode & SK_PROM_MODE_LLC)) { /* Prom. LLC */ - - /* Set the MAC to Promiscuous Mode. */ - SkMacPromiscMode(pAC, IoC, (int) PortNumber, SK_TRUE); - } - else if ((CurPromMode & SK_PROM_MODE_LLC) && - !(NewPromMode & SK_PROM_MODE_LLC)) { /* Norm. LLC */ - - /* Clear Promiscuous Mode. */ - SkMacPromiscMode(pAC, IoC, (int) PortNumber, SK_FALSE); - } - - return (SK_ADDR_SUCCESS); - -} /* SkAddrGmacPromiscuousChange */ - -#endif /* YUKON */ - -#ifndef SK_SLIM - -/****************************************************************************** - * - * SkAddrSwap - swap address info - * - * Description: - * This routine swaps address info of two ports. - * - * Context: - * runtime, pageable - * may be called after SK_INIT_IO - * - * Returns: - * SK_ADDR_SUCCESS - * SK_ADDR_ILLEGAL_PORT - */ -int SkAddrSwap( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -SK_U32 FromPortNumber, /* Port1 Index */ -SK_U32 ToPortNumber) /* Port2 Index */ -{ - int i; - SK_U8 Byte; - SK_MAC_ADDR MacAddr; - SK_U32 DWord; - - if (FromPortNumber >= (SK_U32) pAC->GIni.GIMacsFound) { - return (SK_ADDR_ILLEGAL_PORT); - } - - if (ToPortNumber >= (SK_U32) pAC->GIni.GIMacsFound) { - return (SK_ADDR_ILLEGAL_PORT); - } - - if (pAC->Rlmt.Port[FromPortNumber].Net != pAC->Rlmt.Port[ToPortNumber].Net) { - return (SK_ADDR_ILLEGAL_PORT); - } - - /* - * Swap: - * - Exact Match Entries (GEnesis and Yukon) - * Yukon uses first entry for the logical MAC - * address (stored in the second GMAC register). - * - FirstExactMatchRlmt (GEnesis only) - * - NextExactMatchRlmt (GEnesis only) - * - FirstExactMatchDrv (GEnesis only) - * - NextExactMatchDrv (GEnesis only) - * - 64-bit filter (InexactFilter) - * - Promiscuous Mode - * of ports. - */ - - for (i = 0; i < SK_ADDR_EXACT_MATCHES; i++) { - MacAddr = pAC->Addr.Port[FromPortNumber].Exact[i]; - pAC->Addr.Port[FromPortNumber].Exact[i] = - pAC->Addr.Port[ToPortNumber].Exact[i]; - pAC->Addr.Port[ToPortNumber].Exact[i] = MacAddr; - } - - for (i = 0; i < 8; i++) { - Byte = pAC->Addr.Port[FromPortNumber].InexactFilter.Bytes[i]; - pAC->Addr.Port[FromPortNumber].InexactFilter.Bytes[i] = - pAC->Addr.Port[ToPortNumber].InexactFilter.Bytes[i]; - pAC->Addr.Port[ToPortNumber].InexactFilter.Bytes[i] = Byte; - } - - i = pAC->Addr.Port[FromPortNumber].PromMode; - pAC->Addr.Port[FromPortNumber].PromMode = pAC->Addr.Port[ToPortNumber].PromMode; - pAC->Addr.Port[ToPortNumber].PromMode = i; - - if (pAC->GIni.GIGenesis) { - DWord = pAC->Addr.Port[FromPortNumber].FirstExactMatchRlmt; - pAC->Addr.Port[FromPortNumber].FirstExactMatchRlmt = - pAC->Addr.Port[ToPortNumber].FirstExactMatchRlmt; - pAC->Addr.Port[ToPortNumber].FirstExactMatchRlmt = DWord; - - DWord = pAC->Addr.Port[FromPortNumber].NextExactMatchRlmt; - pAC->Addr.Port[FromPortNumber].NextExactMatchRlmt = - pAC->Addr.Port[ToPortNumber].NextExactMatchRlmt; - pAC->Addr.Port[ToPortNumber].NextExactMatchRlmt = DWord; - - DWord = pAC->Addr.Port[FromPortNumber].FirstExactMatchDrv; - pAC->Addr.Port[FromPortNumber].FirstExactMatchDrv = - pAC->Addr.Port[ToPortNumber].FirstExactMatchDrv; - pAC->Addr.Port[ToPortNumber].FirstExactMatchDrv = DWord; - - DWord = pAC->Addr.Port[FromPortNumber].NextExactMatchDrv; - pAC->Addr.Port[FromPortNumber].NextExactMatchDrv = - pAC->Addr.Port[ToPortNumber].NextExactMatchDrv; - pAC->Addr.Port[ToPortNumber].NextExactMatchDrv = DWord; - } - - /* CAUTION: Solution works if only ports of one adapter are in use. */ - for (i = 0; (SK_U32) i < pAC->Rlmt.Net[pAC->Rlmt.Port[ToPortNumber]. - Net->NetNumber].NumPorts; i++) { - if (pAC->Rlmt.Net[pAC->Rlmt.Port[ToPortNumber].Net->NetNumber]. - Port[i]->PortNumber == ToPortNumber) { - pAC->Addr.Net[pAC->Rlmt.Port[ToPortNumber].Net->NetNumber]. - ActivePort = i; - /* 20001207 RA: Was "ToPortNumber;". */ - } - } - - (void) SkAddrMcUpdate(pAC, IoC, FromPortNumber); - (void) SkAddrMcUpdate(pAC, IoC, ToPortNumber); - - return (SK_ADDR_SUCCESS); - -} /* SkAddrSwap */ - -#endif /* !SK_SLIM */ - -#ifdef __cplusplus -} -#endif /* __cplusplus */ - diff --git a/drivers/net/sk98lin/skdim.c b/drivers/net/sk98lin/skdim.c deleted file mode 100644 index 37ce03fb8de3..000000000000 --- a/drivers/net/sk98lin/skdim.c +++ /dev/null @@ -1,742 +0,0 @@ -/****************************************************************************** - * - * Name: skdim.c - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.5 $ - * Date: $Date: 2003/11/28 12:55:40 $ - * Purpose: All functions to maintain interrupt moderation - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * This module is intended to manage the dynamic interrupt moderation on both - * GEnesis and Yukon adapters. - * - * Include File Hierarchy: - * - * "skdrv1st.h" - * "skdrv2nd.h" - * - ******************************************************************************/ - -#ifndef lint -static const char SysKonnectFileId[] = - "@(#) $Id: skdim.c,v 1.5 2003/11/28 12:55:40 rroesler Exp $ (C) SysKonnect."; -#endif - -#define __SKADDR_C - -#ifdef __cplusplus -#error C++ is not yet supported. -extern "C" { -#endif - -/******************************************************************************* -** -** Includes -** -*******************************************************************************/ - -#ifndef __INC_SKDRV1ST_H -#include "h/skdrv1st.h" -#endif - -#ifndef __INC_SKDRV2ND_H -#include "h/skdrv2nd.h" -#endif - -#include <linux/kernel_stat.h> - -/******************************************************************************* -** -** Defines -** -*******************************************************************************/ - -/******************************************************************************* -** -** Typedefs -** -*******************************************************************************/ - -/******************************************************************************* -** -** Local function prototypes -** -*******************************************************************************/ - -static unsigned int GetCurrentSystemLoad(SK_AC *pAC); -static SK_U64 GetIsrCalls(SK_AC *pAC); -static SK_BOOL IsIntModEnabled(SK_AC *pAC); -static void SetCurrIntCtr(SK_AC *pAC); -static void EnableIntMod(SK_AC *pAC); -static void DisableIntMod(SK_AC *pAC); -static void ResizeDimTimerDuration(SK_AC *pAC); -static void DisplaySelectedModerationType(SK_AC *pAC); -static void DisplaySelectedModerationMask(SK_AC *pAC); -static void DisplayDescrRatio(SK_AC *pAC); - -/******************************************************************************* -** -** Global variables -** -*******************************************************************************/ - -/******************************************************************************* -** -** Local variables -** -*******************************************************************************/ - -/******************************************************************************* -** -** Global functions -** -*******************************************************************************/ - -/******************************************************************************* -** Function : SkDimModerate -** Description : Called in every ISR to check if moderation is to be applied -** or not for the current number of interrupts -** Programmer : Ralph Roesler -** Last Modified: 22-mar-03 -** Returns : void (!) -** Notes : - -*******************************************************************************/ - -void -SkDimModerate(SK_AC *pAC) { - unsigned int CurrSysLoad = 0; /* expressed in percent */ - unsigned int LoadIncrease = 0; /* expressed in percent */ - SK_U64 ThresholdInts = 0; - SK_U64 IsrCallsPerSec = 0; - -#define M_DIMINFO pAC->DynIrqModInfo - - if (!IsIntModEnabled(pAC)) { - if (M_DIMINFO.IntModTypeSelect == C_INT_MOD_DYNAMIC) { - CurrSysLoad = GetCurrentSystemLoad(pAC); - if (CurrSysLoad > 75) { - /* - ** More than 75% total system load! Enable the moderation - ** to shield the system against too many interrupts. - */ - EnableIntMod(pAC); - } else if (CurrSysLoad > M_DIMINFO.PrevSysLoad) { - LoadIncrease = (CurrSysLoad - M_DIMINFO.PrevSysLoad); - if (LoadIncrease > ((M_DIMINFO.PrevSysLoad * - C_INT_MOD_ENABLE_PERCENTAGE) / 100)) { - if (CurrSysLoad > 10) { - /* - ** More than 50% increase with respect to the - ** previous load of the system. Most likely this - ** is due to our ISR-proc... - */ - EnableIntMod(pAC); - } - } - } else { - /* - ** Neither too much system load at all nor too much increase - ** with respect to the previous system load. Hence, we can leave - ** the ISR-handling like it is without enabling moderation. - */ - } - M_DIMINFO.PrevSysLoad = CurrSysLoad; - } - } else { - if (M_DIMINFO.IntModTypeSelect == C_INT_MOD_DYNAMIC) { - ThresholdInts = ((M_DIMINFO.MaxModIntsPerSec * - C_INT_MOD_DISABLE_PERCENTAGE) / 100); - IsrCallsPerSec = GetIsrCalls(pAC); - if (IsrCallsPerSec <= ThresholdInts) { - /* - ** The number of interrupts within the last second is - ** lower than the disable_percentage of the desried - ** maxrate. Therefore we can disable the moderation. - */ - DisableIntMod(pAC); - M_DIMINFO.MaxModIntsPerSec = - (M_DIMINFO.MaxModIntsPerSecUpperLimit + - M_DIMINFO.MaxModIntsPerSecLowerLimit) / 2; - } else { - /* - ** The number of interrupts per sec is the same as expected. - ** Evalulate the descriptor-ratio. If it has changed, a resize - ** in the moderation timer might be useful - */ - if (M_DIMINFO.AutoSizing) { - ResizeDimTimerDuration(pAC); - } - } - } - } - - /* - ** Some information to the log... - */ - if (M_DIMINFO.DisplayStats) { - DisplaySelectedModerationType(pAC); - DisplaySelectedModerationMask(pAC); - DisplayDescrRatio(pAC); - } - - M_DIMINFO.NbrProcessedDescr = 0; - SetCurrIntCtr(pAC); -} - -/******************************************************************************* -** Function : SkDimStartModerationTimer -** Description : Starts the audit-timer for the dynamic interrupt moderation -** Programmer : Ralph Roesler -** Last Modified: 22-mar-03 -** Returns : void (!) -** Notes : - -*******************************************************************************/ - -void -SkDimStartModerationTimer(SK_AC *pAC) { - SK_EVPARA EventParam; /* Event struct for timer event */ - - SK_MEMSET((char *) &EventParam, 0, sizeof(EventParam)); - EventParam.Para32[0] = SK_DRV_MODERATION_TIMER; - SkTimerStart(pAC, pAC->IoBase, &pAC->DynIrqModInfo.ModTimer, - SK_DRV_MODERATION_TIMER_LENGTH, - SKGE_DRV, SK_DRV_TIMER, EventParam); -} - -/******************************************************************************* -** Function : SkDimEnableModerationIfNeeded -** Description : Either enables or disables moderation -** Programmer : Ralph Roesler -** Last Modified: 22-mar-03 -** Returns : void (!) -** Notes : This function is called when a particular adapter is opened -** There is no Disable function, because when all interrupts -** might be disable, the moderation timer has no meaning at all -******************************************************************************/ - -void -SkDimEnableModerationIfNeeded(SK_AC *pAC) { - - if (M_DIMINFO.IntModTypeSelect == C_INT_MOD_STATIC) { - EnableIntMod(pAC); /* notification print in this function */ - } else if (M_DIMINFO.IntModTypeSelect == C_INT_MOD_DYNAMIC) { - SkDimStartModerationTimer(pAC); - if (M_DIMINFO.DisplayStats) { - printk("Dynamic moderation has been enabled\n"); - } - } else { - if (M_DIMINFO.DisplayStats) { - printk("No moderation has been enabled\n"); - } - } -} - -/******************************************************************************* -** Function : SkDimDisplayModerationSettings -** Description : Displays the current settings regarding interrupt moderation -** Programmer : Ralph Roesler -** Last Modified: 22-mar-03 -** Returns : void (!) -** Notes : - -*******************************************************************************/ - -void -SkDimDisplayModerationSettings(SK_AC *pAC) { - DisplaySelectedModerationType(pAC); - DisplaySelectedModerationMask(pAC); -} - -/******************************************************************************* -** -** Local functions -** -*******************************************************************************/ - -/******************************************************************************* -** Function : GetCurrentSystemLoad -** Description : Retrieves the current system load of the system. This load -** is evaluated for all processors within the system. -** Programmer : Ralph Roesler -** Last Modified: 22-mar-03 -** Returns : unsigned int: load expressed in percentage -** Notes : The possible range being returned is from 0 up to 100. -** Whereas 0 means 'no load at all' and 100 'system fully loaded' -** It is impossible to determine what actually causes the system -** to be in 100%, but maybe that is due to too much interrupts. -*******************************************************************************/ - -static unsigned int -GetCurrentSystemLoad(SK_AC *pAC) { - unsigned long jif = jiffies; - unsigned int UserTime = 0; - unsigned int SystemTime = 0; - unsigned int NiceTime = 0; - unsigned int IdleTime = 0; - unsigned int TotalTime = 0; - unsigned int UsedTime = 0; - unsigned int SystemLoad = 0; - - /* unsigned int NbrCpu = 0; */ - - /* - ** The following lines have been commented out, because - ** from kernel 2.5.44 onwards, the kernel-owned structure - ** - ** struct kernel_stat kstat - ** - ** is not marked as an exported symbol in the file - ** - ** kernel/ksyms.c - ** - ** As a consequence, using this driver as KLM is not possible - ** and any access of the structure kernel_stat via the - ** dedicated macros kstat_cpu(i).cpustat.xxx is to be avoided. - ** - ** The kstat-information might be added again in future - ** versions of the 2.5.xx kernel, but for the time being, - ** number of interrupts will serve as indication how much - ** load we currently have... - ** - ** for (NbrCpu = 0; NbrCpu < num_online_cpus(); NbrCpu++) { - ** UserTime = UserTime + kstat_cpu(NbrCpu).cpustat.user; - ** NiceTime = NiceTime + kstat_cpu(NbrCpu).cpustat.nice; - ** SystemTime = SystemTime + kstat_cpu(NbrCpu).cpustat.system; - ** } - */ - SK_U64 ThresholdInts = 0; - SK_U64 IsrCallsPerSec = 0; - - ThresholdInts = ((M_DIMINFO.MaxModIntsPerSec * - C_INT_MOD_ENABLE_PERCENTAGE) + 100); - IsrCallsPerSec = GetIsrCalls(pAC); - if (IsrCallsPerSec >= ThresholdInts) { - /* - ** We do not know how much the real CPU-load is! - ** Return 80% as a default in order to activate DIM - */ - SystemLoad = 80; - return (SystemLoad); - } - - UsedTime = UserTime + NiceTime + SystemTime; - - IdleTime = jif * num_online_cpus() - UsedTime; - TotalTime = UsedTime + IdleTime; - - SystemLoad = ( 100 * (UsedTime - M_DIMINFO.PrevUsedTime) ) / - (TotalTime - M_DIMINFO.PrevTotalTime); - - if (M_DIMINFO.DisplayStats) { - printk("Current system load is: %u\n", SystemLoad); - } - - M_DIMINFO.PrevTotalTime = TotalTime; - M_DIMINFO.PrevUsedTime = UsedTime; - - return (SystemLoad); -} - -/******************************************************************************* -** Function : GetIsrCalls -** Description : Depending on the selected moderation mask, this function will -** return the number of interrupts handled in the previous time- -** frame. This evaluated number is based on the current number -** of interrupts stored in PNMI-context and the previous stored -** interrupts. -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : int: the number of interrupts being executed in the last -** timeframe -** Notes : It makes only sense to call this function, when dynamic -** interrupt moderation is applied -*******************************************************************************/ - -static SK_U64 -GetIsrCalls(SK_AC *pAC) { - SK_U64 RxPort0IntDiff = 0; - SK_U64 RxPort1IntDiff = 0; - SK_U64 TxPort0IntDiff = 0; - SK_U64 TxPort1IntDiff = 0; - - if (pAC->DynIrqModInfo.MaskIrqModeration == IRQ_MASK_TX_ONLY) { - if (pAC->GIni.GIMacsFound == 2) { - TxPort1IntDiff = pAC->Pnmi.Port[1].TxIntrCts - - pAC->DynIrqModInfo.PrevPort1TxIntrCts; - } - TxPort0IntDiff = pAC->Pnmi.Port[0].TxIntrCts - - pAC->DynIrqModInfo.PrevPort0TxIntrCts; - } else if (pAC->DynIrqModInfo.MaskIrqModeration == IRQ_MASK_RX_ONLY) { - if (pAC->GIni.GIMacsFound == 2) { - RxPort1IntDiff = pAC->Pnmi.Port[1].RxIntrCts - - pAC->DynIrqModInfo.PrevPort1RxIntrCts; - } - RxPort0IntDiff = pAC->Pnmi.Port[0].RxIntrCts - - pAC->DynIrqModInfo.PrevPort0RxIntrCts; - } else { - if (pAC->GIni.GIMacsFound == 2) { - RxPort1IntDiff = pAC->Pnmi.Port[1].RxIntrCts - - pAC->DynIrqModInfo.PrevPort1RxIntrCts; - TxPort1IntDiff = pAC->Pnmi.Port[1].TxIntrCts - - pAC->DynIrqModInfo.PrevPort1TxIntrCts; - } - RxPort0IntDiff = pAC->Pnmi.Port[0].RxIntrCts - - pAC->DynIrqModInfo.PrevPort0RxIntrCts; - TxPort0IntDiff = pAC->Pnmi.Port[0].TxIntrCts - - pAC->DynIrqModInfo.PrevPort0TxIntrCts; - } - - return (RxPort0IntDiff + RxPort1IntDiff + TxPort0IntDiff + TxPort1IntDiff); -} - -/******************************************************************************* -** Function : GetRxCalls -** Description : This function will return the number of times a receive inter- -** rupt was processed. This is needed to evaluate any resizing -** factor. -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : SK_U64: the number of RX-ints being processed -** Notes : It makes only sense to call this function, when dynamic -** interrupt moderation is applied -*******************************************************************************/ - -static SK_U64 -GetRxCalls(SK_AC *pAC) { - SK_U64 RxPort0IntDiff = 0; - SK_U64 RxPort1IntDiff = 0; - - if (pAC->GIni.GIMacsFound == 2) { - RxPort1IntDiff = pAC->Pnmi.Port[1].RxIntrCts - - pAC->DynIrqModInfo.PrevPort1RxIntrCts; - } - RxPort0IntDiff = pAC->Pnmi.Port[0].RxIntrCts - - pAC->DynIrqModInfo.PrevPort0RxIntrCts; - - return (RxPort0IntDiff + RxPort1IntDiff); -} - -/******************************************************************************* -** Function : SetCurrIntCtr -** Description : Will store the current number orf occured interrupts in the -** adapter context. This is needed to evaluated the number of -** interrupts within a current timeframe. -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : void (!) -** Notes : - -*******************************************************************************/ - -static void -SetCurrIntCtr(SK_AC *pAC) { - if (pAC->GIni.GIMacsFound == 2) { - pAC->DynIrqModInfo.PrevPort1RxIntrCts = pAC->Pnmi.Port[1].RxIntrCts; - pAC->DynIrqModInfo.PrevPort1TxIntrCts = pAC->Pnmi.Port[1].TxIntrCts; - } - pAC->DynIrqModInfo.PrevPort0RxIntrCts = pAC->Pnmi.Port[0].RxIntrCts; - pAC->DynIrqModInfo.PrevPort0TxIntrCts = pAC->Pnmi.Port[0].TxIntrCts; -} - -/******************************************************************************* -** Function : IsIntModEnabled() -** Description : Retrieves the current value of the interrupts moderation -** command register. Its content determines whether any -** moderation is running or not. -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : SK_TRUE : if mod timer running -** SK_FALSE : if no moderation is being performed -** Notes : - -*******************************************************************************/ - -static SK_BOOL -IsIntModEnabled(SK_AC *pAC) { - unsigned long CtrCmd; - - SK_IN32(pAC->IoBase, B2_IRQM_CTRL, &CtrCmd); - if ((CtrCmd & TIM_START) == TIM_START) { - return SK_TRUE; - } else { - return SK_FALSE; - } -} - -/******************************************************************************* -** Function : EnableIntMod() -** Description : Enables the interrupt moderation using the values stored in -** in the pAC->DynIntMod data structure -** Programmer : Ralph Roesler -** Last Modified: 22-mar-03 -** Returns : - -** Notes : - -*******************************************************************************/ - -static void -EnableIntMod(SK_AC *pAC) { - unsigned long ModBase; - - if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) { - ModBase = C_CLK_FREQ_GENESIS / pAC->DynIrqModInfo.MaxModIntsPerSec; - } else { - ModBase = C_CLK_FREQ_YUKON / pAC->DynIrqModInfo.MaxModIntsPerSec; - } - - SK_OUT32(pAC->IoBase, B2_IRQM_INI, ModBase); - SK_OUT32(pAC->IoBase, B2_IRQM_MSK, pAC->DynIrqModInfo.MaskIrqModeration); - SK_OUT32(pAC->IoBase, B2_IRQM_CTRL, TIM_START); - if (M_DIMINFO.DisplayStats) { - printk("Enabled interrupt moderation (%i ints/sec)\n", - M_DIMINFO.MaxModIntsPerSec); - } -} - -/******************************************************************************* -** Function : DisableIntMod() -** Description : Disables the interrupt moderation independent of what inter- -** rupts are running or not -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : - -** Notes : - -*******************************************************************************/ - -static void -DisableIntMod(SK_AC *pAC) { - - SK_OUT32(pAC->IoBase, B2_IRQM_CTRL, TIM_STOP); - if (M_DIMINFO.DisplayStats) { - printk("Disabled interrupt moderation\n"); - } -} - -/******************************************************************************* -** Function : ResizeDimTimerDuration(); -** Description : Checks the current used descriptor ratio and resizes the -** duration timer (longer/smaller) if possible. -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : - -** Notes : There are both maximum and minimum timer duration value. -** This function assumes that interrupt moderation is already -** enabled! -*******************************************************************************/ - -static void -ResizeDimTimerDuration(SK_AC *pAC) { - SK_BOOL IncreaseTimerDuration; - int TotalMaxNbrDescr; - int UsedDescrRatio; - int RatioDiffAbs; - int RatioDiffRel; - int NewMaxModIntsPerSec; - int ModAdjValue; - long ModBase; - - /* - ** Check first if we are allowed to perform any modification - */ - if (IsIntModEnabled(pAC)) { - if (M_DIMINFO.IntModTypeSelect != C_INT_MOD_DYNAMIC) { - return; - } else { - if (M_DIMINFO.ModJustEnabled) { - M_DIMINFO.ModJustEnabled = SK_FALSE; - return; - } - } - } - - /* - ** If we got until here, we have to evaluate the amount of the - ** descriptor ratio change... - */ - TotalMaxNbrDescr = pAC->RxDescrPerRing * GetRxCalls(pAC); - UsedDescrRatio = (M_DIMINFO.NbrProcessedDescr * 100) / TotalMaxNbrDescr; - - if (UsedDescrRatio > M_DIMINFO.PrevUsedDescrRatio) { - RatioDiffAbs = (UsedDescrRatio - M_DIMINFO.PrevUsedDescrRatio); - RatioDiffRel = (RatioDiffAbs * 100) / UsedDescrRatio; - M_DIMINFO.PrevUsedDescrRatio = UsedDescrRatio; - IncreaseTimerDuration = SK_FALSE; /* in other words: DECREASE */ - } else if (UsedDescrRatio < M_DIMINFO.PrevUsedDescrRatio) { - RatioDiffAbs = (M_DIMINFO.PrevUsedDescrRatio - UsedDescrRatio); - RatioDiffRel = (RatioDiffAbs * 100) / M_DIMINFO.PrevUsedDescrRatio; - M_DIMINFO.PrevUsedDescrRatio = UsedDescrRatio; - IncreaseTimerDuration = SK_TRUE; /* in other words: INCREASE */ - } else { - RatioDiffAbs = (M_DIMINFO.PrevUsedDescrRatio - UsedDescrRatio); - RatioDiffRel = (RatioDiffAbs * 100) / M_DIMINFO.PrevUsedDescrRatio; - M_DIMINFO.PrevUsedDescrRatio = UsedDescrRatio; - IncreaseTimerDuration = SK_TRUE; /* in other words: INCREASE */ - } - - /* - ** Now we can determine the change in percent - */ - if ((RatioDiffRel >= 0) && (RatioDiffRel <= 5) ) { - ModAdjValue = 1; /* 1% change - maybe some other value in future */ - } else if ((RatioDiffRel > 5) && (RatioDiffRel <= 10) ) { - ModAdjValue = 1; /* 1% change - maybe some other value in future */ - } else if ((RatioDiffRel > 10) && (RatioDiffRel <= 15) ) { - ModAdjValue = 1; /* 1% change - maybe some other value in future */ - } else { - ModAdjValue = 1; /* 1% change - maybe some other value in future */ - } - - if (IncreaseTimerDuration) { - NewMaxModIntsPerSec = M_DIMINFO.MaxModIntsPerSec + - (M_DIMINFO.MaxModIntsPerSec * ModAdjValue) / 100; - } else { - NewMaxModIntsPerSec = M_DIMINFO.MaxModIntsPerSec - - (M_DIMINFO.MaxModIntsPerSec * ModAdjValue) / 100; - } - - /* - ** Check if we exceed boundaries... - */ - if ( (NewMaxModIntsPerSec > M_DIMINFO.MaxModIntsPerSecUpperLimit) || - (NewMaxModIntsPerSec < M_DIMINFO.MaxModIntsPerSecLowerLimit)) { - if (M_DIMINFO.DisplayStats) { - printk("Cannot change ModTim from %i to %i ints/sec\n", - M_DIMINFO.MaxModIntsPerSec, NewMaxModIntsPerSec); - } - return; - } else { - if (M_DIMINFO.DisplayStats) { - printk("Resized ModTim from %i to %i ints/sec\n", - M_DIMINFO.MaxModIntsPerSec, NewMaxModIntsPerSec); - } - } - - M_DIMINFO.MaxModIntsPerSec = NewMaxModIntsPerSec; - - if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) { - ModBase = C_CLK_FREQ_GENESIS / pAC->DynIrqModInfo.MaxModIntsPerSec; - } else { - ModBase = C_CLK_FREQ_YUKON / pAC->DynIrqModInfo.MaxModIntsPerSec; - } - - /* - ** We do not need to touch any other registers - */ - SK_OUT32(pAC->IoBase, B2_IRQM_INI, ModBase); -} - -/******************************************************************************* -** Function : DisplaySelectedModerationType() -** Description : Displays what type of moderation we have -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : void! -** Notes : - -*******************************************************************************/ - -static void -DisplaySelectedModerationType(SK_AC *pAC) { - - if (pAC->DynIrqModInfo.DisplayStats) { - if (pAC->DynIrqModInfo.IntModTypeSelect == C_INT_MOD_STATIC) { - printk("Static int moderation runs with %i INTS/sec\n", - pAC->DynIrqModInfo.MaxModIntsPerSec); - } else if (pAC->DynIrqModInfo.IntModTypeSelect == C_INT_MOD_DYNAMIC) { - if (IsIntModEnabled(pAC)) { - printk("Dynamic int moderation runs with %i INTS/sec\n", - pAC->DynIrqModInfo.MaxModIntsPerSec); - } else { - printk("Dynamic int moderation currently not applied\n"); - } - } else { - printk("No interrupt moderation selected!\n"); - } - } -} - -/******************************************************************************* -** Function : DisplaySelectedModerationMask() -** Description : Displays what interrupts are moderated -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : void! -** Notes : - -*******************************************************************************/ - -static void -DisplaySelectedModerationMask(SK_AC *pAC) { - - if (pAC->DynIrqModInfo.DisplayStats) { - if (pAC->DynIrqModInfo.IntModTypeSelect != C_INT_MOD_NONE) { - switch (pAC->DynIrqModInfo.MaskIrqModeration) { - case IRQ_MASK_TX_ONLY: - printk("Only Tx-interrupts are moderated\n"); - break; - case IRQ_MASK_RX_ONLY: - printk("Only Rx-interrupts are moderated\n"); - break; - case IRQ_MASK_SP_ONLY: - printk("Only special-interrupts are moderated\n"); - break; - case IRQ_MASK_TX_RX: - printk("Tx- and Rx-interrupts are moderated\n"); - break; - case IRQ_MASK_SP_RX: - printk("Special- and Rx-interrupts are moderated\n"); - break; - case IRQ_MASK_SP_TX: - printk("Special- and Tx-interrupts are moderated\n"); - break; - case IRQ_MASK_RX_TX_SP: - printk("All Rx-, Tx and special-interrupts are moderated\n"); - break; - default: - printk("Don't know what is moderated\n"); - break; - } - } else { - printk("No specific interrupts masked for moderation\n"); - } - } -} - -/******************************************************************************* -** Function : DisplayDescrRatio -** Description : Like the name states... -** Programmer : Ralph Roesler -** Last Modified: 23-mar-03 -** Returns : void! -** Notes : - -*******************************************************************************/ - -static void -DisplayDescrRatio(SK_AC *pAC) { - int TotalMaxNbrDescr = 0; - - if (pAC->DynIrqModInfo.DisplayStats) { - TotalMaxNbrDescr = pAC->RxDescrPerRing * GetRxCalls(pAC); - printk("Ratio descriptors: %i/%i\n", - M_DIMINFO.NbrProcessedDescr, TotalMaxNbrDescr); - } -} - -/******************************************************************************* -** -** End of file -** -*******************************************************************************/ diff --git a/drivers/net/sk98lin/skethtool.c b/drivers/net/sk98lin/skethtool.c deleted file mode 100644 index 36460694eb82..000000000000 --- a/drivers/net/sk98lin/skethtool.c +++ /dev/null @@ -1,628 +0,0 @@ -/****************************************************************************** - * - * Name: skethtool.c - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.7 $ - * Date: $Date: 2004/09/29 13:32:07 $ - * Purpose: All functions regarding ethtool handling - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2004 Marvell. - * - * Driver for Marvell Yukon/2 chipset and SysKonnect Gigabit Ethernet - * Server Adapters. - * - * Author: Ralph Roesler (rroesler@syskonnect.de) - * Mirko Lindner (mlindner@syskonnect.de) - * - * Address all question to: linux@syskonnect.de - * - * The technical manual for the adapters is available from SysKonnect's - * web pages: www.syskonnect.com - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - *****************************************************************************/ - -#include "h/skdrv1st.h" -#include "h/skdrv2nd.h" -#include "h/skversion.h" - -#include <linux/ethtool.h> -#include <linux/timer.h> -#include <linux/delay.h> - -/****************************************************************************** - * - * Defines - * - *****************************************************************************/ - -#define SUPP_COPPER_ALL (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | \ - SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | \ - SUPPORTED_1000baseT_Half| SUPPORTED_1000baseT_Full| \ - SUPPORTED_TP) - -#define ADV_COPPER_ALL (ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full | \ - ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full | \ - ADVERTISED_1000baseT_Half| ADVERTISED_1000baseT_Full| \ - ADVERTISED_TP) - -#define SUPP_FIBRE_ALL (SUPPORTED_1000baseT_Full | \ - SUPPORTED_FIBRE | \ - SUPPORTED_Autoneg) - -#define ADV_FIBRE_ALL (ADVERTISED_1000baseT_Full | \ - ADVERTISED_FIBRE | \ - ADVERTISED_Autoneg) - - -/****************************************************************************** - * - * Local Functions - * - *****************************************************************************/ - -/***************************************************************************** - * - * getSettings - retrieves the current settings of the selected adapter - * - * Description: - * The current configuration of the selected adapter is returned. - * This configuration involves a)speed, b)duplex and c)autoneg plus - * a number of other variables. - * - * Returns: always 0 - * - */ -static int getSettings(struct net_device *dev, struct ethtool_cmd *ecmd) -{ - const DEV_NET *pNet = netdev_priv(dev); - int port = pNet->PortNr; - const SK_AC *pAC = pNet->pAC; - const SK_GEPORT *pPort = &pAC->GIni.GP[port]; - - static int DuplexAutoNegConfMap[9][3]= { - { -1 , -1 , -1 }, - { 0 , -1 , -1 }, - { SK_LMODE_HALF , DUPLEX_HALF, AUTONEG_DISABLE }, - { SK_LMODE_FULL , DUPLEX_FULL, AUTONEG_DISABLE }, - { SK_LMODE_AUTOHALF , DUPLEX_HALF, AUTONEG_ENABLE }, - { SK_LMODE_AUTOFULL , DUPLEX_FULL, AUTONEG_ENABLE }, - { SK_LMODE_AUTOBOTH , DUPLEX_FULL, AUTONEG_ENABLE }, - { SK_LMODE_AUTOSENSE , -1 , -1 }, - { SK_LMODE_INDETERMINATED, -1 , -1 } - }; - static int SpeedConfMap[6][2] = { - { 0 , -1 }, - { SK_LSPEED_AUTO , -1 }, - { SK_LSPEED_10MBPS , SPEED_10 }, - { SK_LSPEED_100MBPS , SPEED_100 }, - { SK_LSPEED_1000MBPS , SPEED_1000 }, - { SK_LSPEED_INDETERMINATED, -1 } - }; - static int AdvSpeedMap[6][2] = { - { 0 , -1 }, - { SK_LSPEED_AUTO , -1 }, - { SK_LSPEED_10MBPS , ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full }, - { SK_LSPEED_100MBPS , ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full }, - { SK_LSPEED_1000MBPS , ADVERTISED_1000baseT_Half | ADVERTISED_1000baseT_Full}, - { SK_LSPEED_INDETERMINATED, -1 } - }; - - ecmd->phy_address = port; - ecmd->speed = SpeedConfMap[pPort->PLinkSpeedUsed][1]; - ecmd->duplex = DuplexAutoNegConfMap[pPort->PLinkModeStatus][1]; - ecmd->autoneg = DuplexAutoNegConfMap[pPort->PLinkModeStatus][2]; - ecmd->transceiver = XCVR_INTERNAL; - - if (pAC->GIni.GICopperType) { - ecmd->port = PORT_TP; - ecmd->supported = (SUPP_COPPER_ALL|SUPPORTED_Autoneg); - if (pAC->GIni.GIGenesis) { - ecmd->supported &= ~(SUPPORTED_10baseT_Half); - ecmd->supported &= ~(SUPPORTED_10baseT_Full); - ecmd->supported &= ~(SUPPORTED_100baseT_Half); - ecmd->supported &= ~(SUPPORTED_100baseT_Full); - } else { - if (pAC->GIni.GIChipId == CHIP_ID_YUKON) { - ecmd->supported &= ~(SUPPORTED_1000baseT_Half); - } -#ifdef CHIP_ID_YUKON_FE - if (pAC->GIni.GIChipId == CHIP_ID_YUKON_FE) { - ecmd->supported &= ~(SUPPORTED_1000baseT_Half); - ecmd->supported &= ~(SUPPORTED_1000baseT_Full); - } -#endif - } - if (pAC->GIni.GP[0].PLinkSpeed != SK_LSPEED_AUTO) { - ecmd->advertising = AdvSpeedMap[pPort->PLinkSpeed][1]; - if (pAC->GIni.GIChipId == CHIP_ID_YUKON) { - ecmd->advertising &= ~(SUPPORTED_1000baseT_Half); - } - } else { - ecmd->advertising = ecmd->supported; - } - - if (ecmd->autoneg == AUTONEG_ENABLE) - ecmd->advertising |= ADVERTISED_Autoneg; - } else { - ecmd->port = PORT_FIBRE; - ecmd->supported = SUPP_FIBRE_ALL; - ecmd->advertising = ADV_FIBRE_ALL; - } - return 0; -} - -/* - * MIB infrastructure uses instance value starting at 1 - * based on board and port. - */ -static inline u32 pnmiInstance(const DEV_NET *pNet) -{ - return 1 + (pNet->pAC->RlmtNets == 2) + pNet->PortNr; -} - -/***************************************************************************** - * - * setSettings - configures the settings of a selected adapter - * - * Description: - * Possible settings that may be altered are a)speed, b)duplex or - * c)autonegotiation. - * - * Returns: - * 0: everything fine, no error - * <0: the return value is the error code of the failure - */ -static int setSettings(struct net_device *dev, struct ethtool_cmd *ecmd) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - u32 instance; - char buf[4]; - int len = 1; - - if (ecmd->speed != SPEED_10 && ecmd->speed != SPEED_100 - && ecmd->speed != SPEED_1000) - return -EINVAL; - - if (ecmd->duplex != DUPLEX_HALF && ecmd->duplex != DUPLEX_FULL) - return -EINVAL; - - if (ecmd->autoneg != AUTONEG_DISABLE && ecmd->autoneg != AUTONEG_ENABLE) - return -EINVAL; - - if (ecmd->autoneg == AUTONEG_DISABLE) - *buf = (ecmd->duplex == DUPLEX_FULL) - ? SK_LMODE_FULL : SK_LMODE_HALF; - else - *buf = (ecmd->duplex == DUPLEX_FULL) - ? SK_LMODE_AUTOFULL : SK_LMODE_AUTOHALF; - - instance = pnmiInstance(pNet); - if (SkPnmiSetVar(pAC, pAC->IoBase, OID_SKGE_LINK_MODE, - &buf, &len, instance, pNet->NetNr) != SK_PNMI_ERR_OK) - return -EINVAL; - - switch(ecmd->speed) { - case SPEED_1000: - *buf = SK_LSPEED_1000MBPS; - break; - case SPEED_100: - *buf = SK_LSPEED_100MBPS; - break; - case SPEED_10: - *buf = SK_LSPEED_10MBPS; - } - - if (SkPnmiSetVar(pAC, pAC->IoBase, OID_SKGE_SPEED_MODE, - &buf, &len, instance, pNet->NetNr) != SK_PNMI_ERR_OK) - return -EINVAL; - - return 0; -} - -/***************************************************************************** - * - * getDriverInfo - returns generic driver and adapter information - * - * Description: - * Generic driver information is returned via this function, such as - * the name of the driver, its version and and firmware version. - * In addition to this, the location of the selected adapter is - * returned as a bus info string (e.g. '01:05.0'). - * - * Returns: N/A - * - */ -static void getDriverInfo(struct net_device *dev, struct ethtool_drvinfo *info) -{ - const DEV_NET *pNet = netdev_priv(dev); - const SK_AC *pAC = pNet->pAC; - char vers[32]; - - snprintf(vers, sizeof(vers)-1, VER_STRING "(v%d.%d)", - (pAC->GIni.GIPciHwRev >> 4) & 0xf, pAC->GIni.GIPciHwRev & 0xf); - - strlcpy(info->driver, DRIVER_FILE_NAME, sizeof(info->driver)); - strcpy(info->version, vers); - strcpy(info->fw_version, "N/A"); - strlcpy(info->bus_info, pci_name(pAC->PciDev), ETHTOOL_BUSINFO_LEN); -} - -/* - * Ethtool statistics support. - */ -static const char StringsStats[][ETH_GSTRING_LEN] = { - "rx_packets", "tx_packets", - "rx_bytes", "tx_bytes", - "rx_errors", "tx_errors", - "rx_dropped", "tx_dropped", - "multicasts", "collisions", - "rx_length_errors", "rx_buffer_overflow_errors", - "rx_crc_errors", "rx_frame_errors", - "rx_too_short_errors", "rx_too_long_errors", - "rx_carrier_extension_errors", "rx_symbol_errors", - "rx_llc_mac_size_errors", "rx_carrier_errors", - "rx_jabber_errors", "rx_missed_errors", - "tx_abort_collision_errors", "tx_carrier_errors", - "tx_buffer_underrun_errors", "tx_heartbeat_errors", - "tx_window_errors", -}; - -static int getStatsCount(struct net_device *dev) -{ - return ARRAY_SIZE(StringsStats); -} - -static void getStrings(struct net_device *dev, u32 stringset, u8 *data) -{ - switch(stringset) { - case ETH_SS_STATS: - memcpy(data, *StringsStats, sizeof(StringsStats)); - break; - } -} - -static void getEthtoolStats(struct net_device *dev, - struct ethtool_stats *stats, u64 *data) -{ - const DEV_NET *pNet = netdev_priv(dev); - const SK_AC *pAC = pNet->pAC; - const SK_PNMI_STRUCT_DATA *pPnmiStruct = &pAC->PnmiStruct; - - *data++ = pPnmiStruct->Stat[0].StatRxOkCts; - *data++ = pPnmiStruct->Stat[0].StatTxOkCts; - *data++ = pPnmiStruct->Stat[0].StatRxOctetsOkCts; - *data++ = pPnmiStruct->Stat[0].StatTxOctetsOkCts; - *data++ = pPnmiStruct->InErrorsCts; - *data++ = pPnmiStruct->Stat[0].StatTxSingleCollisionCts; - *data++ = pPnmiStruct->RxNoBufCts; - *data++ = pPnmiStruct->TxNoBufCts; - *data++ = pPnmiStruct->Stat[0].StatRxMulticastOkCts; - *data++ = pPnmiStruct->Stat[0].StatTxSingleCollisionCts; - *data++ = pPnmiStruct->Stat[0].StatRxRuntCts; - *data++ = pPnmiStruct->Stat[0].StatRxFifoOverflowCts; - *data++ = pPnmiStruct->Stat[0].StatRxFcsCts; - *data++ = pPnmiStruct->Stat[0].StatRxFramingCts; - *data++ = pPnmiStruct->Stat[0].StatRxShortsCts; - *data++ = pPnmiStruct->Stat[0].StatRxTooLongCts; - *data++ = pPnmiStruct->Stat[0].StatRxCextCts; - *data++ = pPnmiStruct->Stat[0].StatRxSymbolCts; - *data++ = pPnmiStruct->Stat[0].StatRxIRLengthCts; - *data++ = pPnmiStruct->Stat[0].StatRxCarrierCts; - *data++ = pPnmiStruct->Stat[0].StatRxJabberCts; - *data++ = pPnmiStruct->Stat[0].StatRxMissedCts; - *data++ = pAC->stats.tx_aborted_errors; - *data++ = pPnmiStruct->Stat[0].StatTxCarrierCts; - *data++ = pPnmiStruct->Stat[0].StatTxFifoUnderrunCts; - *data++ = pPnmiStruct->Stat[0].StatTxCarrierCts; - *data++ = pAC->stats.tx_window_errors; -} - - -/***************************************************************************** - * - * toggleLeds - Changes the LED state of an adapter - * - * Description: - * This function changes the current state of all LEDs of an adapter so - * that it can be located by a user. - * - * Returns: N/A - * - */ -static void toggleLeds(DEV_NET *pNet, int on) -{ - SK_AC *pAC = pNet->pAC; - int port = pNet->PortNr; - void __iomem *io = pAC->IoBase; - - if (pAC->GIni.GIGenesis) { - SK_OUT8(io, MR_ADDR(port,LNK_LED_REG), - on ? SK_LNK_ON : SK_LNK_OFF); - SkGeYellowLED(pAC, io, - on ? (LED_ON >> 1) : (LED_OFF >> 1)); - SkGeXmitLED(pAC, io, MR_ADDR(port,RX_LED_INI), - on ? SK_LED_TST : SK_LED_DIS); - - if (pAC->GIni.GP[port].PhyType == SK_PHY_BCOM) - SkXmPhyWrite(pAC, io, port, PHY_BCOM_P_EXT_CTRL, - on ? PHY_B_PEC_LED_ON : PHY_B_PEC_LED_OFF); - else if (pAC->GIni.GP[port].PhyType == SK_PHY_LONE) - SkXmPhyWrite(pAC, io, port, PHY_LONE_LED_CFG, - on ? 0x0800 : PHY_L_LC_LEDT); - else - SkGeXmitLED(pAC, io, MR_ADDR(port,TX_LED_INI), - on ? SK_LED_TST : SK_LED_DIS); - } else { - const u16 YukLedOn = (PHY_M_LED_MO_DUP(MO_LED_ON) | - PHY_M_LED_MO_10(MO_LED_ON) | - PHY_M_LED_MO_100(MO_LED_ON) | - PHY_M_LED_MO_1000(MO_LED_ON) | - PHY_M_LED_MO_RX(MO_LED_ON)); - const u16 YukLedOff = (PHY_M_LED_MO_DUP(MO_LED_OFF) | - PHY_M_LED_MO_10(MO_LED_OFF) | - PHY_M_LED_MO_100(MO_LED_OFF) | - PHY_M_LED_MO_1000(MO_LED_OFF) | - PHY_M_LED_MO_RX(MO_LED_OFF)); - - - SkGmPhyWrite(pAC,io,port,PHY_MARV_LED_CTRL,0); - SkGmPhyWrite(pAC,io,port,PHY_MARV_LED_OVER, - on ? YukLedOn : YukLedOff); - } -} - -/***************************************************************************** - * - * skGeBlinkTimer - Changes the LED state of an adapter - * - * Description: - * This function changes the current state of all LEDs of an adapter so - * that it can be located by a user. If the requested time interval for - * this test has elapsed, this function cleans up everything that was - * temporarily setup during the locate NIC test. This involves of course - * also closing or opening any adapter so that the initial board state - * is recovered. - * - * Returns: N/A - * - */ -void SkGeBlinkTimer(unsigned long data) -{ - struct net_device *dev = (struct net_device *) data; - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - - toggleLeds(pNet, pAC->LedsOn); - - pAC->LedsOn = !pAC->LedsOn; - mod_timer(&pAC->BlinkTimer, jiffies + HZ/4); -} - -/***************************************************************************** - * - * locateDevice - start the locate NIC feature of the elected adapter - * - * Description: - * This function is used if the user want to locate a particular NIC. - * All LEDs are regularly switched on and off, so the NIC can easily - * be identified. - * - * Returns: - * ==0: everything fine, no error, locateNIC test was started - * !=0: one locateNIC test runs already - * - */ -static int locateDevice(struct net_device *dev, u32 data) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - - if(!data || data > (u32)(MAX_SCHEDULE_TIMEOUT / HZ)) - data = (u32)(MAX_SCHEDULE_TIMEOUT / HZ); - - /* start blinking */ - pAC->LedsOn = 0; - mod_timer(&pAC->BlinkTimer, jiffies); - msleep_interruptible(data * 1000); - del_timer_sync(&pAC->BlinkTimer); - toggleLeds(pNet, 0); - - return 0; -} - -/***************************************************************************** - * - * getPauseParams - retrieves the pause parameters - * - * Description: - * All current pause parameters of a selected adapter are placed - * in the passed ethtool_pauseparam structure and are returned. - * - * Returns: N/A - * - */ -static void getPauseParams(struct net_device *dev, struct ethtool_pauseparam *epause) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - SK_GEPORT *pPort = &pAC->GIni.GP[pNet->PortNr]; - - epause->rx_pause = (pPort->PFlowCtrlMode == SK_FLOW_MODE_SYMMETRIC) || - (pPort->PFlowCtrlMode == SK_FLOW_MODE_SYM_OR_REM); - - epause->tx_pause = epause->rx_pause || (pPort->PFlowCtrlMode == SK_FLOW_MODE_LOC_SEND); - epause->autoneg = epause->rx_pause || epause->tx_pause; -} - -/***************************************************************************** - * - * setPauseParams - configures the pause parameters of an adapter - * - * Description: - * This function sets the Rx or Tx pause parameters - * - * Returns: - * ==0: everything fine, no error - * !=0: the return value is the error code of the failure - */ -static int setPauseParams(struct net_device *dev , struct ethtool_pauseparam *epause) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - SK_GEPORT *pPort = &pAC->GIni.GP[pNet->PortNr]; - u32 instance = pnmiInstance(pNet); - struct ethtool_pauseparam old; - u8 oldspeed = pPort->PLinkSpeedUsed; - char buf[4]; - int len = 1; - int ret; - - /* - ** we have to determine the current settings to see if - ** the operator requested any modification of the flow - ** control parameters... - */ - getPauseParams(dev, &old); - - /* - ** perform modifications regarding the changes - ** requested by the operator - */ - if (epause->autoneg != old.autoneg) - *buf = epause->autoneg ? SK_FLOW_MODE_NONE : SK_FLOW_MODE_SYMMETRIC; - else { - if (epause->rx_pause && epause->tx_pause) - *buf = SK_FLOW_MODE_SYMMETRIC; - else if (epause->rx_pause && !epause->tx_pause) - *buf = SK_FLOW_MODE_SYM_OR_REM; - else if (!epause->rx_pause && epause->tx_pause) - *buf = SK_FLOW_MODE_LOC_SEND; - else - *buf = SK_FLOW_MODE_NONE; - } - - ret = SkPnmiSetVar(pAC, pAC->IoBase, OID_SKGE_FLOWCTRL_MODE, - &buf, &len, instance, pNet->NetNr); - - if (ret != SK_PNMI_ERR_OK) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_CTRL, - ("ethtool (sk98lin): error changing rx/tx pause (%i)\n", ret)); - goto err; - } - - /* - ** It may be that autoneg has been disabled! Therefore - ** set the speed to the previously used value... - */ - if (!epause->autoneg) { - len = 1; - ret = SkPnmiSetVar(pAC, pAC->IoBase, OID_SKGE_SPEED_MODE, - &oldspeed, &len, instance, pNet->NetNr); - if (ret != SK_PNMI_ERR_OK) - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_CTRL, - ("ethtool (sk98lin): error setting speed (%i)\n", ret)); - } - err: - return ret ? -EIO : 0; -} - -/* Only Yukon supports checksum offload. */ -static int setScatterGather(struct net_device *dev, u32 data) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - - if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) - return -EOPNOTSUPP; - return ethtool_op_set_sg(dev, data); -} - -static int setTxCsum(struct net_device *dev, u32 data) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - - if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) - return -EOPNOTSUPP; - - return ethtool_op_set_tx_csum(dev, data); -} - -static u32 getRxCsum(struct net_device *dev) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - - return pAC->RxPort[pNet->PortNr].RxCsum; -} - -static int setRxCsum(struct net_device *dev, u32 data) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - - if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) - return -EOPNOTSUPP; - - pAC->RxPort[pNet->PortNr].RxCsum = data != 0; - return 0; -} - -static int getRegsLen(struct net_device *dev) -{ - return 0x4000; -} - -/* - * Returns copy of whole control register region - * Note: skip RAM address register because accessing it will - * cause bus hangs! - */ -static void getRegs(struct net_device *dev, struct ethtool_regs *regs, - void *p) -{ - DEV_NET *pNet = netdev_priv(dev); - const void __iomem *io = pNet->pAC->IoBase; - - regs->version = 1; - memset(p, 0, regs->len); - memcpy_fromio(p, io, B3_RAM_ADDR); - - memcpy_fromio(p + B3_RI_WTO_R1, io + B3_RI_WTO_R1, - regs->len - B3_RI_WTO_R1); -} - -const struct ethtool_ops SkGeEthtoolOps = { - .get_settings = getSettings, - .set_settings = setSettings, - .get_drvinfo = getDriverInfo, - .get_strings = getStrings, - .get_stats_count = getStatsCount, - .get_ethtool_stats = getEthtoolStats, - .phys_id = locateDevice, - .get_pauseparam = getPauseParams, - .set_pauseparam = setPauseParams, - .get_link = ethtool_op_get_link, - .get_perm_addr = ethtool_op_get_perm_addr, - .get_sg = ethtool_op_get_sg, - .set_sg = setScatterGather, - .get_tx_csum = ethtool_op_get_tx_csum, - .set_tx_csum = setTxCsum, - .get_rx_csum = getRxCsum, - .set_rx_csum = setRxCsum, - .get_regs = getRegs, - .get_regs_len = getRegsLen, -}; diff --git a/drivers/net/sk98lin/skge.c b/drivers/net/sk98lin/skge.c deleted file mode 100644 index bf218621db16..000000000000 --- a/drivers/net/sk98lin/skge.c +++ /dev/null @@ -1,5211 +0,0 @@ -/****************************************************************************** - * - * Name: skge.c - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.45 $ - * Date: $Date: 2004/02/12 14:41:02 $ - * Purpose: The main driver source module - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * Driver for Marvell Yukon chipset and SysKonnect Gigabit Ethernet - * Server Adapters. - * - * Created 10-Feb-1999, based on Linux' acenic.c, 3c59x.c and - * SysKonnects GEnesis Solaris driver - * Author: Christoph Goos (cgoos@syskonnect.de) - * Mirko Lindner (mlindner@syskonnect.de) - * - * Address all question to: linux@syskonnect.de - * - * The technical manual for the adapters is available from SysKonnect's - * web pages: www.syskonnect.com - * Goto "Support" and search Knowledge Base for "manual". - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Possible compiler options (#define xxx / -Dxxx): - * - * debugging can be enable by changing SK_DEBUG_CHKMOD and - * SK_DEBUG_CHKCAT in makefile (described there). - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * This is the main module of the Linux GE driver. - * - * All source files except skge.c, skdrv1st.h, skdrv2nd.h and sktypes.h - * are part of SysKonnect's COMMON MODULES for the SK-98xx adapters. - * Those are used for drivers on multiple OS', so some thing may seem - * unnecessary complicated on Linux. Please do not try to 'clean up' - * them without VERY good reasons, because this will make it more - * difficult to keep the Linux driver in synchronisation with the - * other versions. - * - * Include file hierarchy: - * - * <linux/module.h> - * - * "h/skdrv1st.h" - * <linux/types.h> - * <linux/kernel.h> - * <linux/string.h> - * <linux/errno.h> - * <linux/ioport.h> - * <linux/slab.h> - * <linux/interrupt.h> - * <linux/pci.h> - * <linux/bitops.h> - * <asm/byteorder.h> - * <asm/io.h> - * <linux/netdevice.h> - * <linux/etherdevice.h> - * <linux/skbuff.h> - * those three depending on kernel version used: - * <linux/bios32.h> - * <linux/init.h> - * <asm/uaccess.h> - * <net/checksum.h> - * - * "h/skerror.h" - * "h/skdebug.h" - * "h/sktypes.h" - * "h/lm80.h" - * "h/xmac_ii.h" - * - * "h/skdrv2nd.h" - * "h/skqueue.h" - * "h/skgehwt.h" - * "h/sktimer.h" - * "h/ski2c.h" - * "h/skgepnmi.h" - * "h/skvpd.h" - * "h/skgehw.h" - * "h/skgeinit.h" - * "h/skaddr.h" - * "h/skgesirq.h" - * "h/skrlmt.h" - * - ******************************************************************************/ - -#include "h/skversion.h" - -#include <linux/in.h> -#include <linux/module.h> -#include <linux/moduleparam.h> -#include <linux/init.h> -#include <linux/dma-mapping.h> -#include <linux/ip.h> -#include <linux/mii.h> -#include <linux/mm.h> - -#include "h/skdrv1st.h" -#include "h/skdrv2nd.h" - -/******************************************************************************* - * - * Defines - * - ******************************************************************************/ - -/* for debuging on x86 only */ -/* #define BREAKPOINT() asm(" int $3"); */ - -/* use the transmit hw checksum driver functionality */ -#define USE_SK_TX_CHECKSUM - -/* use the receive hw checksum driver functionality */ -#define USE_SK_RX_CHECKSUM - -/* use the scatter-gather functionality with sendfile() */ -#define SK_ZEROCOPY - -/* use of a transmit complete interrupt */ -#define USE_TX_COMPLETE - -/* - * threshold for copying small receive frames - * set to 0 to avoid copying, set to 9001 to copy all frames - */ -#define SK_COPY_THRESHOLD 50 - -/* number of adapters that can be configured via command line params */ -#define SK_MAX_CARD_PARAM 16 - - - -/* - * use those defines for a compile-in version of the driver instead - * of command line parameters - */ -// #define LINK_SPEED_A {"Auto", } -// #define LINK_SPEED_B {"Auto", } -// #define AUTO_NEG_A {"Sense", } -// #define AUTO_NEG_B {"Sense", } -// #define DUP_CAP_A {"Both", } -// #define DUP_CAP_B {"Both", } -// #define FLOW_CTRL_A {"SymOrRem", } -// #define FLOW_CTRL_B {"SymOrRem", } -// #define ROLE_A {"Auto", } -// #define ROLE_B {"Auto", } -// #define PREF_PORT {"A", } -// #define CON_TYPE {"Auto", } -// #define RLMT_MODE {"CheckLinkState", } - -#define DEV_KFREE_SKB(skb) dev_kfree_skb(skb) -#define DEV_KFREE_SKB_IRQ(skb) dev_kfree_skb_irq(skb) -#define DEV_KFREE_SKB_ANY(skb) dev_kfree_skb_any(skb) - - -/* Set blink mode*/ -#define OEM_CONFIG_VALUE ( SK_ACT_LED_BLINK | \ - SK_DUP_LED_NORMAL | \ - SK_LED_LINK100_ON) - - -/* Isr return value */ -#define SkIsrRetVar irqreturn_t -#define SkIsrRetNone IRQ_NONE -#define SkIsrRetHandled IRQ_HANDLED - - -/******************************************************************************* - * - * Local Function Prototypes - * - ******************************************************************************/ - -static void FreeResources(struct SK_NET_DEVICE *dev); -static int SkGeBoardInit(struct SK_NET_DEVICE *dev, SK_AC *pAC); -static SK_BOOL BoardAllocMem(SK_AC *pAC); -static void BoardFreeMem(SK_AC *pAC); -static void BoardInitMem(SK_AC *pAC); -static void SetupRing(SK_AC*, void*, uintptr_t, RXD**, RXD**, RXD**, int*, SK_BOOL); -static SkIsrRetVar SkGeIsr(int irq, void *dev_id); -static SkIsrRetVar SkGeIsrOnePort(int irq, void *dev_id); -static int SkGeOpen(struct SK_NET_DEVICE *dev); -static int SkGeClose(struct SK_NET_DEVICE *dev); -static int SkGeXmit(struct sk_buff *skb, struct SK_NET_DEVICE *dev); -static int SkGeSetMacAddr(struct SK_NET_DEVICE *dev, void *p); -static void SkGeSetRxMode(struct SK_NET_DEVICE *dev); -static struct net_device_stats *SkGeStats(struct SK_NET_DEVICE *dev); -static int SkGeIoctl(struct SK_NET_DEVICE *dev, struct ifreq *rq, int cmd); -static void GetConfiguration(SK_AC*); -static int XmitFrame(SK_AC*, TX_PORT*, struct sk_buff*); -static void FreeTxDescriptors(SK_AC*pAC, TX_PORT*); -static void FillRxRing(SK_AC*, RX_PORT*); -static SK_BOOL FillRxDescriptor(SK_AC*, RX_PORT*); -static void ReceiveIrq(SK_AC*, RX_PORT*, SK_BOOL); -static void ClearAndStartRx(SK_AC*, int); -static void ClearTxIrq(SK_AC*, int, int); -static void ClearRxRing(SK_AC*, RX_PORT*); -static void ClearTxRing(SK_AC*, TX_PORT*); -static int SkGeChangeMtu(struct SK_NET_DEVICE *dev, int new_mtu); -static void PortReInitBmu(SK_AC*, int); -static int SkGeIocMib(DEV_NET*, unsigned int, int); -static int SkGeInitPCI(SK_AC *pAC); -static void StartDrvCleanupTimer(SK_AC *pAC); -static void StopDrvCleanupTimer(SK_AC *pAC); -static int XmitFrameSG(SK_AC*, TX_PORT*, struct sk_buff*); - -#ifdef SK_DIAG_SUPPORT -static SK_U32 ParseDeviceNbrFromSlotName(const char *SlotName); -static int SkDrvInitAdapter(SK_AC *pAC, int devNbr); -static int SkDrvDeInitAdapter(SK_AC *pAC, int devNbr); -#endif - -/******************************************************************************* - * - * Extern Function Prototypes - * - ******************************************************************************/ -extern void SkDimEnableModerationIfNeeded(SK_AC *pAC); -extern void SkDimDisplayModerationSettings(SK_AC *pAC); -extern void SkDimStartModerationTimer(SK_AC *pAC); -extern void SkDimModerate(SK_AC *pAC); -extern void SkGeBlinkTimer(unsigned long data); - -#ifdef DEBUG -static void DumpMsg(struct sk_buff*, char*); -static void DumpData(char*, int); -static void DumpLong(char*, int); -#endif - -/* global variables *********************************************************/ -static SK_BOOL DoPrintInterfaceChange = SK_TRUE; -extern const struct ethtool_ops SkGeEthtoolOps; - -/* local variables **********************************************************/ -static uintptr_t TxQueueAddr[SK_MAX_MACS][2] = {{0x680, 0x600},{0x780, 0x700}}; -static uintptr_t RxQueueAddr[SK_MAX_MACS] = {0x400, 0x480}; - -/***************************************************************************** - * - * SkPciWriteCfgDWord - write a 32 bit value to pci config space - * - * Description: - * This routine writes a 32 bit value to the pci configuration - * space. - * - * Returns: - * 0 - indicate everything worked ok. - * != 0 - error indication - */ -static inline int SkPciWriteCfgDWord( -SK_AC *pAC, /* Adapter Control structure pointer */ -int PciAddr, /* PCI register address */ -SK_U32 Val) /* pointer to store the read value */ -{ - pci_write_config_dword(pAC->PciDev, PciAddr, Val); - return(0); -} /* SkPciWriteCfgDWord */ - -/***************************************************************************** - * - * SkGeInitPCI - Init the PCI resources - * - * Description: - * This function initialize the PCI resources and IO - * - * Returns: - * 0 - indicate everything worked ok. - * != 0 - error indication - */ -static __devinit int SkGeInitPCI(SK_AC *pAC) -{ - struct SK_NET_DEVICE *dev = pAC->dev[0]; - struct pci_dev *pdev = pAC->PciDev; - int retval; - - dev->mem_start = pci_resource_start (pdev, 0); - pci_set_master(pdev); - - retval = pci_request_regions(pdev, "sk98lin"); - if (retval) - goto out; - -#ifdef SK_BIG_ENDIAN - /* - * On big endian machines, we use the adapter's aibility of - * reading the descriptors as big endian. - */ - { - SK_U32 our2; - SkPciReadCfgDWord(pAC, PCI_OUR_REG_2, &our2); - our2 |= PCI_REV_DESC; - SkPciWriteCfgDWord(pAC, PCI_OUR_REG_2, our2); - } -#endif - - /* - * Remap the regs into kernel space. - */ - pAC->IoBase = ioremap_nocache(dev->mem_start, 0x4000); - if (!pAC->IoBase) { - retval = -EIO; - goto out_release; - } - - return 0; - - out_release: - pci_release_regions(pdev); - out: - return retval; -} - - -/***************************************************************************** - * - * FreeResources - release resources allocated for adapter - * - * Description: - * This function releases the IRQ, unmaps the IO and - * frees the desriptor ring. - * - * Returns: N/A - * - */ -static void FreeResources(struct SK_NET_DEVICE *dev) -{ -SK_U32 AllocFlag; -DEV_NET *pNet; -SK_AC *pAC; - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - AllocFlag = pAC->AllocFlag; - if (pAC->PciDev) { - pci_release_regions(pAC->PciDev); - } - if (AllocFlag & SK_ALLOC_IRQ) { - free_irq(dev->irq, dev); - } - if (pAC->IoBase) { - iounmap(pAC->IoBase); - } - if (pAC->pDescrMem) { - BoardFreeMem(pAC); - } - -} /* FreeResources */ - -MODULE_AUTHOR("Mirko Lindner <mlindner@syskonnect.de>"); -MODULE_DESCRIPTION("SysKonnect SK-NET Gigabit Ethernet SK-98xx driver"); -MODULE_LICENSE("GPL"); - -#ifdef LINK_SPEED_A -static char *Speed_A[SK_MAX_CARD_PARAM] = LINK_SPEED; -#else -static char *Speed_A[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef LINK_SPEED_B -static char *Speed_B[SK_MAX_CARD_PARAM] = LINK_SPEED; -#else -static char *Speed_B[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef AUTO_NEG_A -static char *AutoNeg_A[SK_MAX_CARD_PARAM] = AUTO_NEG_A; -#else -static char *AutoNeg_A[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef DUP_CAP_A -static char *DupCap_A[SK_MAX_CARD_PARAM] = DUP_CAP_A; -#else -static char *DupCap_A[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef FLOW_CTRL_A -static char *FlowCtrl_A[SK_MAX_CARD_PARAM] = FLOW_CTRL_A; -#else -static char *FlowCtrl_A[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef ROLE_A -static char *Role_A[SK_MAX_CARD_PARAM] = ROLE_A; -#else -static char *Role_A[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef AUTO_NEG_B -static char *AutoNeg_B[SK_MAX_CARD_PARAM] = AUTO_NEG_B; -#else -static char *AutoNeg_B[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef DUP_CAP_B -static char *DupCap_B[SK_MAX_CARD_PARAM] = DUP_CAP_B; -#else -static char *DupCap_B[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef FLOW_CTRL_B -static char *FlowCtrl_B[SK_MAX_CARD_PARAM] = FLOW_CTRL_B; -#else -static char *FlowCtrl_B[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef ROLE_B -static char *Role_B[SK_MAX_CARD_PARAM] = ROLE_B; -#else -static char *Role_B[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef CON_TYPE -static char *ConType[SK_MAX_CARD_PARAM] = CON_TYPE; -#else -static char *ConType[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef PREF_PORT -static char *PrefPort[SK_MAX_CARD_PARAM] = PREF_PORT; -#else -static char *PrefPort[SK_MAX_CARD_PARAM] = {"", }; -#endif - -#ifdef RLMT_MODE -static char *RlmtMode[SK_MAX_CARD_PARAM] = RLMT_MODE; -#else -static char *RlmtMode[SK_MAX_CARD_PARAM] = {"", }; -#endif - -static int IntsPerSec[SK_MAX_CARD_PARAM]; -static char *Moderation[SK_MAX_CARD_PARAM]; -static char *ModerationMask[SK_MAX_CARD_PARAM]; -static char *AutoSizing[SK_MAX_CARD_PARAM]; -static char *Stats[SK_MAX_CARD_PARAM]; - -module_param_array(Speed_A, charp, NULL, 0); -module_param_array(Speed_B, charp, NULL, 0); -module_param_array(AutoNeg_A, charp, NULL, 0); -module_param_array(AutoNeg_B, charp, NULL, 0); -module_param_array(DupCap_A, charp, NULL, 0); -module_param_array(DupCap_B, charp, NULL, 0); -module_param_array(FlowCtrl_A, charp, NULL, 0); -module_param_array(FlowCtrl_B, charp, NULL, 0); -module_param_array(Role_A, charp, NULL, 0); -module_param_array(Role_B, charp, NULL, 0); -module_param_array(ConType, charp, NULL, 0); -module_param_array(PrefPort, charp, NULL, 0); -module_param_array(RlmtMode, charp, NULL, 0); -/* used for interrupt moderation */ -module_param_array(IntsPerSec, int, NULL, 0); -module_param_array(Moderation, charp, NULL, 0); -module_param_array(Stats, charp, NULL, 0); -module_param_array(ModerationMask, charp, NULL, 0); -module_param_array(AutoSizing, charp, NULL, 0); - -/***************************************************************************** - * - * SkGeBoardInit - do level 0 and 1 initialization - * - * Description: - * This function prepares the board hardware for running. The desriptor - * ring is set up, the IRQ is allocated and the configuration settings - * are examined. - * - * Returns: - * 0, if everything is ok - * !=0, on error - */ -static int __devinit SkGeBoardInit(struct SK_NET_DEVICE *dev, SK_AC *pAC) -{ -short i; -unsigned long Flags; -char *DescrString = "sk98lin: Driver for Linux"; /* this is given to PNMI */ -char *VerStr = VER_STRING; -int Ret; /* return code of request_irq */ -SK_BOOL DualNet; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("IoBase: %08lX\n", (unsigned long)pAC->IoBase)); - for (i=0; i<SK_MAX_MACS; i++) { - pAC->TxPort[i][0].HwAddr = pAC->IoBase + TxQueueAddr[i][0]; - pAC->TxPort[i][0].PortIndex = i; - pAC->RxPort[i].HwAddr = pAC->IoBase + RxQueueAddr[i]; - pAC->RxPort[i].PortIndex = i; - } - - /* Initialize the mutexes */ - for (i=0; i<SK_MAX_MACS; i++) { - spin_lock_init(&pAC->TxPort[i][0].TxDesRingLock); - spin_lock_init(&pAC->RxPort[i].RxDesRingLock); - } - spin_lock_init(&pAC->SlowPathLock); - - /* setup phy_id blink timer */ - pAC->BlinkTimer.function = SkGeBlinkTimer; - pAC->BlinkTimer.data = (unsigned long) dev; - init_timer(&pAC->BlinkTimer); - - /* level 0 init common modules here */ - - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - /* Does a RESET on board ...*/ - if (SkGeInit(pAC, pAC->IoBase, SK_INIT_DATA) != 0) { - printk("HWInit (0) failed.\n"); - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - return -EIO; - } - SkI2cInit( pAC, pAC->IoBase, SK_INIT_DATA); - SkEventInit(pAC, pAC->IoBase, SK_INIT_DATA); - SkPnmiInit( pAC, pAC->IoBase, SK_INIT_DATA); - SkAddrInit( pAC, pAC->IoBase, SK_INIT_DATA); - SkRlmtInit( pAC, pAC->IoBase, SK_INIT_DATA); - SkTimerInit(pAC, pAC->IoBase, SK_INIT_DATA); - - pAC->BoardLevel = SK_INIT_DATA; - pAC->RxBufSize = ETH_BUF_SIZE; - - SK_PNMI_SET_DRIVER_DESCR(pAC, DescrString); - SK_PNMI_SET_DRIVER_VER(pAC, VerStr); - - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - - /* level 1 init common modules here (HW init) */ - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - if (SkGeInit(pAC, pAC->IoBase, SK_INIT_IO) != 0) { - printk("sk98lin: HWInit (1) failed.\n"); - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - return -EIO; - } - SkI2cInit( pAC, pAC->IoBase, SK_INIT_IO); - SkEventInit(pAC, pAC->IoBase, SK_INIT_IO); - SkPnmiInit( pAC, pAC->IoBase, SK_INIT_IO); - SkAddrInit( pAC, pAC->IoBase, SK_INIT_IO); - SkRlmtInit( pAC, pAC->IoBase, SK_INIT_IO); - SkTimerInit(pAC, pAC->IoBase, SK_INIT_IO); - - /* Set chipset type support */ - pAC->ChipsetType = 0; - if ((pAC->GIni.GIChipId == CHIP_ID_YUKON) || - (pAC->GIni.GIChipId == CHIP_ID_YUKON_LITE)) { - pAC->ChipsetType = 1; - } - - GetConfiguration(pAC); - if (pAC->RlmtNets == 2) { - pAC->GIni.GIPortUsage = SK_MUL_LINK; - } - - pAC->BoardLevel = SK_INIT_IO; - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - - if (pAC->GIni.GIMacsFound == 2) { - Ret = request_irq(dev->irq, SkGeIsr, IRQF_SHARED, "sk98lin", dev); - } else if (pAC->GIni.GIMacsFound == 1) { - Ret = request_irq(dev->irq, SkGeIsrOnePort, IRQF_SHARED, - "sk98lin", dev); - } else { - printk(KERN_WARNING "sk98lin: Illegal number of ports: %d\n", - pAC->GIni.GIMacsFound); - return -EIO; - } - - if (Ret) { - printk(KERN_WARNING "sk98lin: Requested IRQ %d is busy.\n", - dev->irq); - return Ret; - } - pAC->AllocFlag |= SK_ALLOC_IRQ; - - /* Alloc memory for this board (Mem for RxD/TxD) : */ - if(!BoardAllocMem(pAC)) { - printk("No memory for descriptor rings.\n"); - return -ENOMEM; - } - - BoardInitMem(pAC); - /* tschilling: New common function with minimum size check. */ - DualNet = SK_FALSE; - if (pAC->RlmtNets == 2) { - DualNet = SK_TRUE; - } - - if (SkGeInitAssignRamToQueues( - pAC, - pAC->ActivePort, - DualNet)) { - BoardFreeMem(pAC); - printk("sk98lin: SkGeInitAssignRamToQueues failed.\n"); - return -EIO; - } - - return (0); -} /* SkGeBoardInit */ - - -/***************************************************************************** - * - * BoardAllocMem - allocate the memory for the descriptor rings - * - * Description: - * This function allocates the memory for all descriptor rings. - * Each ring is aligned for the desriptor alignment and no ring - * has a 4 GByte boundary in it (because the upper 32 bit must - * be constant for all descriptiors in one rings). - * - * Returns: - * SK_TRUE, if all memory could be allocated - * SK_FALSE, if not - */ -static __devinit SK_BOOL BoardAllocMem(SK_AC *pAC) -{ -caddr_t pDescrMem; /* pointer to descriptor memory area */ -size_t AllocLength; /* length of complete descriptor area */ -int i; /* loop counter */ -unsigned long BusAddr; - - - /* rings plus one for alignment (do not cross 4 GB boundary) */ - /* RX_RING_SIZE is assumed bigger than TX_RING_SIZE */ -#if (BITS_PER_LONG == 32) - AllocLength = (RX_RING_SIZE + TX_RING_SIZE) * pAC->GIni.GIMacsFound + 8; -#else - AllocLength = (RX_RING_SIZE + TX_RING_SIZE) * pAC->GIni.GIMacsFound - + RX_RING_SIZE + 8; -#endif - - pDescrMem = pci_alloc_consistent(pAC->PciDev, AllocLength, - &pAC->pDescrMemDMA); - - if (pDescrMem == NULL) { - return (SK_FALSE); - } - pAC->pDescrMem = pDescrMem; - BusAddr = (unsigned long) pAC->pDescrMemDMA; - - /* Descriptors need 8 byte alignment, and this is ensured - * by pci_alloc_consistent. - */ - for (i=0; i<pAC->GIni.GIMacsFound; i++) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_TX_PROGRESS, - ("TX%d/A: pDescrMem: %lX, PhysDescrMem: %lX\n", - i, (unsigned long) pDescrMem, - BusAddr)); - pAC->TxPort[i][0].pTxDescrRing = pDescrMem; - pAC->TxPort[i][0].VTxDescrRing = BusAddr; - pDescrMem += TX_RING_SIZE; - BusAddr += TX_RING_SIZE; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_TX_PROGRESS, - ("RX%d: pDescrMem: %lX, PhysDescrMem: %lX\n", - i, (unsigned long) pDescrMem, - (unsigned long)BusAddr)); - pAC->RxPort[i].pRxDescrRing = pDescrMem; - pAC->RxPort[i].VRxDescrRing = BusAddr; - pDescrMem += RX_RING_SIZE; - BusAddr += RX_RING_SIZE; - } /* for */ - - return (SK_TRUE); -} /* BoardAllocMem */ - - -/**************************************************************************** - * - * BoardFreeMem - reverse of BoardAllocMem - * - * Description: - * Free all memory allocated in BoardAllocMem: adapter context, - * descriptor rings, locks. - * - * Returns: N/A - */ -static void BoardFreeMem( -SK_AC *pAC) -{ -size_t AllocLength; /* length of complete descriptor area */ - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("BoardFreeMem\n")); -#if (BITS_PER_LONG == 32) - AllocLength = (RX_RING_SIZE + TX_RING_SIZE) * pAC->GIni.GIMacsFound + 8; -#else - AllocLength = (RX_RING_SIZE + TX_RING_SIZE) * pAC->GIni.GIMacsFound - + RX_RING_SIZE + 8; -#endif - - pci_free_consistent(pAC->PciDev, AllocLength, - pAC->pDescrMem, pAC->pDescrMemDMA); - pAC->pDescrMem = NULL; -} /* BoardFreeMem */ - - -/***************************************************************************** - * - * BoardInitMem - initiate the descriptor rings - * - * Description: - * This function sets the descriptor rings up in memory. - * The adapter is initialized with the descriptor start addresses. - * - * Returns: N/A - */ -static __devinit void BoardInitMem(SK_AC *pAC) -{ -int i; /* loop counter */ -int RxDescrSize; /* the size of a rx descriptor rounded up to alignment*/ -int TxDescrSize; /* the size of a tx descriptor rounded up to alignment*/ - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("BoardInitMem\n")); - - RxDescrSize = (((sizeof(RXD) - 1) / DESCR_ALIGN) + 1) * DESCR_ALIGN; - pAC->RxDescrPerRing = RX_RING_SIZE / RxDescrSize; - TxDescrSize = (((sizeof(TXD) - 1) / DESCR_ALIGN) + 1) * DESCR_ALIGN; - pAC->TxDescrPerRing = TX_RING_SIZE / RxDescrSize; - - for (i=0; i<pAC->GIni.GIMacsFound; i++) { - SetupRing( - pAC, - pAC->TxPort[i][0].pTxDescrRing, - pAC->TxPort[i][0].VTxDescrRing, - (RXD**)&pAC->TxPort[i][0].pTxdRingHead, - (RXD**)&pAC->TxPort[i][0].pTxdRingTail, - (RXD**)&pAC->TxPort[i][0].pTxdRingPrev, - &pAC->TxPort[i][0].TxdRingFree, - SK_TRUE); - SetupRing( - pAC, - pAC->RxPort[i].pRxDescrRing, - pAC->RxPort[i].VRxDescrRing, - &pAC->RxPort[i].pRxdRingHead, - &pAC->RxPort[i].pRxdRingTail, - &pAC->RxPort[i].pRxdRingPrev, - &pAC->RxPort[i].RxdRingFree, - SK_FALSE); - } -} /* BoardInitMem */ - - -/***************************************************************************** - * - * SetupRing - create one descriptor ring - * - * Description: - * This function creates one descriptor ring in the given memory area. - * The head, tail and number of free descriptors in the ring are set. - * - * Returns: - * none - */ -static void SetupRing( -SK_AC *pAC, -void *pMemArea, /* a pointer to the memory area for the ring */ -uintptr_t VMemArea, /* the virtual bus address of the memory area */ -RXD **ppRingHead, /* address where the head should be written */ -RXD **ppRingTail, /* address where the tail should be written */ -RXD **ppRingPrev, /* address where the tail should be written */ -int *pRingFree, /* address where the # of free descr. goes */ -SK_BOOL IsTx) /* flag: is this a tx ring */ -{ -int i; /* loop counter */ -int DescrSize; /* the size of a descriptor rounded up to alignment*/ -int DescrNum; /* number of descriptors per ring */ -RXD *pDescr; /* pointer to a descriptor (receive or transmit) */ -RXD *pNextDescr; /* pointer to the next descriptor */ -RXD *pPrevDescr; /* pointer to the previous descriptor */ -uintptr_t VNextDescr; /* the virtual bus address of the next descriptor */ - - if (IsTx == SK_TRUE) { - DescrSize = (((sizeof(TXD) - 1) / DESCR_ALIGN) + 1) * - DESCR_ALIGN; - DescrNum = TX_RING_SIZE / DescrSize; - } else { - DescrSize = (((sizeof(RXD) - 1) / DESCR_ALIGN) + 1) * - DESCR_ALIGN; - DescrNum = RX_RING_SIZE / DescrSize; - } - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_TX_PROGRESS, - ("Descriptor size: %d Descriptor Number: %d\n", - DescrSize,DescrNum)); - - pDescr = (RXD*) pMemArea; - pPrevDescr = NULL; - pNextDescr = (RXD*) (((char*)pDescr) + DescrSize); - VNextDescr = VMemArea + DescrSize; - for(i=0; i<DescrNum; i++) { - /* set the pointers right */ - pDescr->VNextRxd = VNextDescr & 0xffffffffULL; - pDescr->pNextRxd = pNextDescr; - if (!IsTx) pDescr->TcpSumStarts = ETH_HLEN << 16 | ETH_HLEN; - - /* advance one step */ - pPrevDescr = pDescr; - pDescr = pNextDescr; - pNextDescr = (RXD*) (((char*)pDescr) + DescrSize); - VNextDescr += DescrSize; - } - pPrevDescr->pNextRxd = (RXD*) pMemArea; - pPrevDescr->VNextRxd = VMemArea; - pDescr = (RXD*) pMemArea; - *ppRingHead = (RXD*) pMemArea; - *ppRingTail = *ppRingHead; - *ppRingPrev = pPrevDescr; - *pRingFree = DescrNum; -} /* SetupRing */ - - -/***************************************************************************** - * - * PortReInitBmu - re-initiate the descriptor rings for one port - * - * Description: - * This function reinitializes the descriptor rings of one port - * in memory. The port must be stopped before. - * The HW is initialized with the descriptor start addresses. - * - * Returns: - * none - */ -static void PortReInitBmu( -SK_AC *pAC, /* pointer to adapter context */ -int PortIndex) /* index of the port for which to re-init */ -{ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("PortReInitBmu ")); - - /* set address of first descriptor of ring in BMU */ - SK_OUT32(pAC->IoBase, TxQueueAddr[PortIndex][TX_PRIO_LOW]+ Q_DA_L, - (uint32_t)(((caddr_t) - (pAC->TxPort[PortIndex][TX_PRIO_LOW].pTxdRingHead) - - pAC->TxPort[PortIndex][TX_PRIO_LOW].pTxDescrRing + - pAC->TxPort[PortIndex][TX_PRIO_LOW].VTxDescrRing) & - 0xFFFFFFFF)); - SK_OUT32(pAC->IoBase, TxQueueAddr[PortIndex][TX_PRIO_LOW]+ Q_DA_H, - (uint32_t)(((caddr_t) - (pAC->TxPort[PortIndex][TX_PRIO_LOW].pTxdRingHead) - - pAC->TxPort[PortIndex][TX_PRIO_LOW].pTxDescrRing + - pAC->TxPort[PortIndex][TX_PRIO_LOW].VTxDescrRing) >> 32)); - SK_OUT32(pAC->IoBase, RxQueueAddr[PortIndex]+Q_DA_L, - (uint32_t)(((caddr_t)(pAC->RxPort[PortIndex].pRxdRingHead) - - pAC->RxPort[PortIndex].pRxDescrRing + - pAC->RxPort[PortIndex].VRxDescrRing) & 0xFFFFFFFF)); - SK_OUT32(pAC->IoBase, RxQueueAddr[PortIndex]+Q_DA_H, - (uint32_t)(((caddr_t)(pAC->RxPort[PortIndex].pRxdRingHead) - - pAC->RxPort[PortIndex].pRxDescrRing + - pAC->RxPort[PortIndex].VRxDescrRing) >> 32)); -} /* PortReInitBmu */ - - -/**************************************************************************** - * - * SkGeIsr - handle adapter interrupts - * - * Description: - * The interrupt routine is called when the network adapter - * generates an interrupt. It may also be called if another device - * shares this interrupt vector with the driver. - * - * Returns: N/A - * - */ -static SkIsrRetVar SkGeIsr(int irq, void *dev_id) -{ -struct SK_NET_DEVICE *dev = (struct SK_NET_DEVICE *)dev_id; -DEV_NET *pNet; -SK_AC *pAC; -SK_U32 IntSrc; /* interrupts source register contents */ - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - - /* - * Check and process if its our interrupt - */ - SK_IN32(pAC->IoBase, B0_SP_ISRC, &IntSrc); - if (IntSrc == 0) { - return SkIsrRetNone; - } - - while (((IntSrc & IRQ_MASK) & ~SPECIAL_IRQS) != 0) { -#if 0 /* software irq currently not used */ - if (IntSrc & IS_IRQ_SW) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("Software IRQ\n")); - } -#endif - if (IntSrc & IS_R1_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF RX1 IRQ\n")); - ReceiveIrq(pAC, &pAC->RxPort[0], SK_TRUE); - SK_PNMI_CNT_RX_INTR(pAC, 0); - } - if (IntSrc & IS_R2_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF RX2 IRQ\n")); - ReceiveIrq(pAC, &pAC->RxPort[1], SK_TRUE); - SK_PNMI_CNT_RX_INTR(pAC, 1); - } -#ifdef USE_TX_COMPLETE /* only if tx complete interrupt used */ - if (IntSrc & IS_XA1_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF AS TX1 IRQ\n")); - SK_PNMI_CNT_TX_INTR(pAC, 0); - spin_lock(&pAC->TxPort[0][TX_PRIO_LOW].TxDesRingLock); - FreeTxDescriptors(pAC, &pAC->TxPort[0][TX_PRIO_LOW]); - spin_unlock(&pAC->TxPort[0][TX_PRIO_LOW].TxDesRingLock); - } - if (IntSrc & IS_XA2_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF AS TX2 IRQ\n")); - SK_PNMI_CNT_TX_INTR(pAC, 1); - spin_lock(&pAC->TxPort[1][TX_PRIO_LOW].TxDesRingLock); - FreeTxDescriptors(pAC, &pAC->TxPort[1][TX_PRIO_LOW]); - spin_unlock(&pAC->TxPort[1][TX_PRIO_LOW].TxDesRingLock); - } -#if 0 /* only if sync. queues used */ - if (IntSrc & IS_XS1_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF SY TX1 IRQ\n")); - SK_PNMI_CNT_TX_INTR(pAC, 1); - spin_lock(&pAC->TxPort[0][TX_PRIO_HIGH].TxDesRingLock); - FreeTxDescriptors(pAC, 0, TX_PRIO_HIGH); - spin_unlock(&pAC->TxPort[0][TX_PRIO_HIGH].TxDesRingLock); - ClearTxIrq(pAC, 0, TX_PRIO_HIGH); - } - if (IntSrc & IS_XS2_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF SY TX2 IRQ\n")); - SK_PNMI_CNT_TX_INTR(pAC, 1); - spin_lock(&pAC->TxPort[1][TX_PRIO_HIGH].TxDesRingLock); - FreeTxDescriptors(pAC, 1, TX_PRIO_HIGH); - spin_unlock(&pAC->TxPort[1][TX_PRIO_HIGH].TxDesRingLock); - ClearTxIrq(pAC, 1, TX_PRIO_HIGH); - } -#endif -#endif - - /* do all IO at once */ - if (IntSrc & IS_R1_F) - ClearAndStartRx(pAC, 0); - if (IntSrc & IS_R2_F) - ClearAndStartRx(pAC, 1); -#ifdef USE_TX_COMPLETE /* only if tx complete interrupt used */ - if (IntSrc & IS_XA1_F) - ClearTxIrq(pAC, 0, TX_PRIO_LOW); - if (IntSrc & IS_XA2_F) - ClearTxIrq(pAC, 1, TX_PRIO_LOW); -#endif - SK_IN32(pAC->IoBase, B0_ISRC, &IntSrc); - } /* while (IntSrc & IRQ_MASK != 0) */ - - IntSrc &= pAC->GIni.GIValIrqMask; - if ((IntSrc & SPECIAL_IRQS) || pAC->CheckQueue) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_INT_SRC, - ("SPECIAL IRQ DP-Cards => %x\n", IntSrc)); - pAC->CheckQueue = SK_FALSE; - spin_lock(&pAC->SlowPathLock); - if (IntSrc & SPECIAL_IRQS) - SkGeSirqIsr(pAC, pAC->IoBase, IntSrc); - - SkEventDispatcher(pAC, pAC->IoBase); - spin_unlock(&pAC->SlowPathLock); - } - /* - * do it all again is case we cleared an interrupt that - * came in after handling the ring (OUTs may be delayed - * in hardware buffers, but are through after IN) - * - * rroesler: has been commented out and shifted to - * SkGeDrvEvent(), because it is timer - * guarded now - * - ReceiveIrq(pAC, &pAC->RxPort[0], SK_TRUE); - ReceiveIrq(pAC, &pAC->RxPort[1], SK_TRUE); - */ - - if (pAC->CheckQueue) { - pAC->CheckQueue = SK_FALSE; - spin_lock(&pAC->SlowPathLock); - SkEventDispatcher(pAC, pAC->IoBase); - spin_unlock(&pAC->SlowPathLock); - } - - /* IRQ is processed - Enable IRQs again*/ - SK_OUT32(pAC->IoBase, B0_IMSK, pAC->GIni.GIValIrqMask); - - return SkIsrRetHandled; -} /* SkGeIsr */ - - -/**************************************************************************** - * - * SkGeIsrOnePort - handle adapter interrupts for single port adapter - * - * Description: - * The interrupt routine is called when the network adapter - * generates an interrupt. It may also be called if another device - * shares this interrupt vector with the driver. - * This is the same as above, but handles only one port. - * - * Returns: N/A - * - */ -static SkIsrRetVar SkGeIsrOnePort(int irq, void *dev_id) -{ -struct SK_NET_DEVICE *dev = (struct SK_NET_DEVICE *)dev_id; -DEV_NET *pNet; -SK_AC *pAC; -SK_U32 IntSrc; /* interrupts source register contents */ - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - - /* - * Check and process if its our interrupt - */ - SK_IN32(pAC->IoBase, B0_SP_ISRC, &IntSrc); - if (IntSrc == 0) { - return SkIsrRetNone; - } - - while (((IntSrc & IRQ_MASK) & ~SPECIAL_IRQS) != 0) { -#if 0 /* software irq currently not used */ - if (IntSrc & IS_IRQ_SW) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("Software IRQ\n")); - } -#endif - if (IntSrc & IS_R1_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF RX1 IRQ\n")); - ReceiveIrq(pAC, &pAC->RxPort[0], SK_TRUE); - SK_PNMI_CNT_RX_INTR(pAC, 0); - } -#ifdef USE_TX_COMPLETE /* only if tx complete interrupt used */ - if (IntSrc & IS_XA1_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF AS TX1 IRQ\n")); - SK_PNMI_CNT_TX_INTR(pAC, 0); - spin_lock(&pAC->TxPort[0][TX_PRIO_LOW].TxDesRingLock); - FreeTxDescriptors(pAC, &pAC->TxPort[0][TX_PRIO_LOW]); - spin_unlock(&pAC->TxPort[0][TX_PRIO_LOW].TxDesRingLock); - } -#if 0 /* only if sync. queues used */ - if (IntSrc & IS_XS1_F) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_INT_SRC, - ("EOF SY TX1 IRQ\n")); - SK_PNMI_CNT_TX_INTR(pAC, 0); - spin_lock(&pAC->TxPort[0][TX_PRIO_HIGH].TxDesRingLock); - FreeTxDescriptors(pAC, 0, TX_PRIO_HIGH); - spin_unlock(&pAC->TxPort[0][TX_PRIO_HIGH].TxDesRingLock); - ClearTxIrq(pAC, 0, TX_PRIO_HIGH); - } -#endif -#endif - - /* do all IO at once */ - if (IntSrc & IS_R1_F) - ClearAndStartRx(pAC, 0); -#ifdef USE_TX_COMPLETE /* only if tx complete interrupt used */ - if (IntSrc & IS_XA1_F) - ClearTxIrq(pAC, 0, TX_PRIO_LOW); -#endif - SK_IN32(pAC->IoBase, B0_ISRC, &IntSrc); - } /* while (IntSrc & IRQ_MASK != 0) */ - - IntSrc &= pAC->GIni.GIValIrqMask; - if ((IntSrc & SPECIAL_IRQS) || pAC->CheckQueue) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_INT_SRC, - ("SPECIAL IRQ SP-Cards => %x\n", IntSrc)); - pAC->CheckQueue = SK_FALSE; - spin_lock(&pAC->SlowPathLock); - if (IntSrc & SPECIAL_IRQS) - SkGeSirqIsr(pAC, pAC->IoBase, IntSrc); - - SkEventDispatcher(pAC, pAC->IoBase); - spin_unlock(&pAC->SlowPathLock); - } - /* - * do it all again is case we cleared an interrupt that - * came in after handling the ring (OUTs may be delayed - * in hardware buffers, but are through after IN) - * - * rroesler: has been commented out and shifted to - * SkGeDrvEvent(), because it is timer - * guarded now - * - ReceiveIrq(pAC, &pAC->RxPort[0], SK_TRUE); - */ - - /* IRQ is processed - Enable IRQs again*/ - SK_OUT32(pAC->IoBase, B0_IMSK, pAC->GIni.GIValIrqMask); - - return SkIsrRetHandled; -} /* SkGeIsrOnePort */ - -#ifdef CONFIG_NET_POLL_CONTROLLER -/**************************************************************************** - * - * SkGePollController - polling receive, for netconsole - * - * Description: - * Polling receive - used by netconsole and other diagnostic tools - * to allow network i/o with interrupts disabled. - * - * Returns: N/A - */ -static void SkGePollController(struct net_device *dev) -{ - disable_irq(dev->irq); - SkGeIsr(dev->irq, dev); - enable_irq(dev->irq); -} -#endif - -/**************************************************************************** - * - * SkGeOpen - handle start of initialized adapter - * - * Description: - * This function starts the initialized adapter. - * The board level variable is set and the adapter is - * brought to full functionality. - * The device flags are set for operation. - * Do all necessary level 2 initialization, enable interrupts and - * give start command to RLMT. - * - * Returns: - * 0 on success - * != 0 on error - */ -static int SkGeOpen( -struct SK_NET_DEVICE *dev) -{ - DEV_NET *pNet; - SK_AC *pAC; - unsigned long Flags; /* for spin lock */ - int i; - SK_EVPARA EvPara; /* an event parameter union */ - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeOpen: pAC=0x%lX:\n", (unsigned long)pAC)); - -#ifdef SK_DIAG_SUPPORT - if (pAC->DiagModeActive == DIAG_ACTIVE) { - if (pAC->Pnmi.DiagAttached == SK_DIAG_RUNNING) { - return (-1); /* still in use by diag; deny actions */ - } - } -#endif - - /* Set blink mode */ - if ((pAC->PciDev->vendor == 0x1186) || (pAC->PciDev->vendor == 0x11ab )) - pAC->GIni.GILedBlinkCtrl = OEM_CONFIG_VALUE; - - if (pAC->BoardLevel == SK_INIT_DATA) { - /* level 1 init common modules here */ - if (SkGeInit(pAC, pAC->IoBase, SK_INIT_IO) != 0) { - printk("%s: HWInit (1) failed.\n", pAC->dev[pNet->PortNr]->name); - return (-1); - } - SkI2cInit (pAC, pAC->IoBase, SK_INIT_IO); - SkEventInit (pAC, pAC->IoBase, SK_INIT_IO); - SkPnmiInit (pAC, pAC->IoBase, SK_INIT_IO); - SkAddrInit (pAC, pAC->IoBase, SK_INIT_IO); - SkRlmtInit (pAC, pAC->IoBase, SK_INIT_IO); - SkTimerInit (pAC, pAC->IoBase, SK_INIT_IO); - pAC->BoardLevel = SK_INIT_IO; - } - - if (pAC->BoardLevel != SK_INIT_RUN) { - /* tschilling: Level 2 init modules here, check return value. */ - if (SkGeInit(pAC, pAC->IoBase, SK_INIT_RUN) != 0) { - printk("%s: HWInit (2) failed.\n", pAC->dev[pNet->PortNr]->name); - return (-1); - } - SkI2cInit (pAC, pAC->IoBase, SK_INIT_RUN); - SkEventInit (pAC, pAC->IoBase, SK_INIT_RUN); - SkPnmiInit (pAC, pAC->IoBase, SK_INIT_RUN); - SkAddrInit (pAC, pAC->IoBase, SK_INIT_RUN); - SkRlmtInit (pAC, pAC->IoBase, SK_INIT_RUN); - SkTimerInit (pAC, pAC->IoBase, SK_INIT_RUN); - pAC->BoardLevel = SK_INIT_RUN; - } - - for (i=0; i<pAC->GIni.GIMacsFound; i++) { - /* Enable transmit descriptor polling. */ - SkGePollTxD(pAC, pAC->IoBase, i, SK_TRUE); - FillRxRing(pAC, &pAC->RxPort[i]); - } - SkGeYellowLED(pAC, pAC->IoBase, 1); - - StartDrvCleanupTimer(pAC); - SkDimEnableModerationIfNeeded(pAC); - SkDimDisplayModerationSettings(pAC); - - pAC->GIni.GIValIrqMask &= IRQ_MASK; - - /* enable Interrupts */ - SK_OUT32(pAC->IoBase, B0_IMSK, pAC->GIni.GIValIrqMask); - SK_OUT32(pAC->IoBase, B0_HWE_IMSK, IRQ_HWE_MASK); - - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - - if ((pAC->RlmtMode != 0) && (pAC->MaxPorts == 0)) { - EvPara.Para32[0] = pAC->RlmtNets; - EvPara.Para32[1] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_SET_NETS, - EvPara); - EvPara.Para32[0] = pAC->RlmtMode; - EvPara.Para32[1] = 0; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_MODE_CHANGE, - EvPara); - } - - EvPara.Para32[0] = pNet->NetNr; - EvPara.Para32[1] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_START, EvPara); - SkEventDispatcher(pAC, pAC->IoBase); - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - - pAC->MaxPorts++; - - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeOpen suceeded\n")); - - return (0); -} /* SkGeOpen */ - - -/**************************************************************************** - * - * SkGeClose - Stop initialized adapter - * - * Description: - * Close initialized adapter. - * - * Returns: - * 0 - on success - * error code - on error - */ -static int SkGeClose( -struct SK_NET_DEVICE *dev) -{ - DEV_NET *pNet; - DEV_NET *newPtrNet; - SK_AC *pAC; - - unsigned long Flags; /* for spin lock */ - int i; - int PortIdx; - SK_EVPARA EvPara; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeClose: pAC=0x%lX ", (unsigned long)pAC)); - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - -#ifdef SK_DIAG_SUPPORT - if (pAC->DiagModeActive == DIAG_ACTIVE) { - if (pAC->DiagFlowCtrl == SK_FALSE) { - /* - ** notify that the interface which has been closed - ** by operator interaction must not be started up - ** again when the DIAG has finished. - */ - newPtrNet = netdev_priv(pAC->dev[0]); - if (newPtrNet == pNet) { - pAC->WasIfUp[0] = SK_FALSE; - } else { - pAC->WasIfUp[1] = SK_FALSE; - } - return 0; /* return to system everything is fine... */ - } else { - pAC->DiagFlowCtrl = SK_FALSE; - } - } -#endif - - netif_stop_queue(dev); - - if (pAC->RlmtNets == 1) - PortIdx = pAC->ActivePort; - else - PortIdx = pNet->NetNr; - - StopDrvCleanupTimer(pAC); - - /* - * Clear multicast table, promiscuous mode .... - */ - SkAddrMcClear(pAC, pAC->IoBase, PortIdx, 0); - SkAddrPromiscuousChange(pAC, pAC->IoBase, PortIdx, - SK_PROM_MODE_NONE); - - if (pAC->MaxPorts == 1) { - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - /* disable interrupts */ - SK_OUT32(pAC->IoBase, B0_IMSK, 0); - EvPara.Para32[0] = pNet->NetNr; - EvPara.Para32[1] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_STOP, EvPara); - SkEventDispatcher(pAC, pAC->IoBase); - SK_OUT32(pAC->IoBase, B0_IMSK, 0); - /* stop the hardware */ - SkGeDeInit(pAC, pAC->IoBase); - pAC->BoardLevel = SK_INIT_DATA; - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - } else { - - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - EvPara.Para32[0] = pNet->NetNr; - EvPara.Para32[1] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_STOP, EvPara); - SkPnmiEvent(pAC, pAC->IoBase, SK_PNMI_EVT_XMAC_RESET, EvPara); - SkEventDispatcher(pAC, pAC->IoBase); - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - - /* Stop port */ - spin_lock_irqsave(&pAC->TxPort[pNet->PortNr] - [TX_PRIO_LOW].TxDesRingLock, Flags); - SkGeStopPort(pAC, pAC->IoBase, pNet->PortNr, - SK_STOP_ALL, SK_HARD_RST); - spin_unlock_irqrestore(&pAC->TxPort[pNet->PortNr] - [TX_PRIO_LOW].TxDesRingLock, Flags); - } - - if (pAC->RlmtNets == 1) { - /* clear all descriptor rings */ - for (i=0; i<pAC->GIni.GIMacsFound; i++) { - ReceiveIrq(pAC, &pAC->RxPort[i], SK_TRUE); - ClearRxRing(pAC, &pAC->RxPort[i]); - ClearTxRing(pAC, &pAC->TxPort[i][TX_PRIO_LOW]); - } - } else { - /* clear port descriptor rings */ - ReceiveIrq(pAC, &pAC->RxPort[pNet->PortNr], SK_TRUE); - ClearRxRing(pAC, &pAC->RxPort[pNet->PortNr]); - ClearTxRing(pAC, &pAC->TxPort[pNet->PortNr][TX_PRIO_LOW]); - } - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeClose: done ")); - - SK_MEMSET(&(pAC->PnmiBackup), 0, sizeof(SK_PNMI_STRUCT_DATA)); - SK_MEMCPY(&(pAC->PnmiBackup), &(pAC->PnmiStruct), - sizeof(SK_PNMI_STRUCT_DATA)); - - pAC->MaxPorts--; - - return (0); -} /* SkGeClose */ - - -/***************************************************************************** - * - * SkGeXmit - Linux frame transmit function - * - * Description: - * The system calls this function to send frames onto the wire. - * It puts the frame in the tx descriptor ring. If the ring is - * full then, the 'tbusy' flag is set. - * - * Returns: - * 0, if everything is ok - * !=0, on error - * WARNING: returning 1 in 'tbusy' case caused system crashes (double - * allocated skb's) !!! - */ -static int SkGeXmit(struct sk_buff *skb, struct SK_NET_DEVICE *dev) -{ -DEV_NET *pNet; -SK_AC *pAC; -int Rc; /* return code of XmitFrame */ - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - - if ((!skb_shinfo(skb)->nr_frags) || - (pAC->GIni.GIChipId == CHIP_ID_GENESIS)) { - /* Don't activate scatter-gather and hardware checksum */ - - if (pAC->RlmtNets == 2) - Rc = XmitFrame( - pAC, - &pAC->TxPort[pNet->PortNr][TX_PRIO_LOW], - skb); - else - Rc = XmitFrame( - pAC, - &pAC->TxPort[pAC->ActivePort][TX_PRIO_LOW], - skb); - } else { - /* scatter-gather and hardware TCP checksumming anabled*/ - if (pAC->RlmtNets == 2) - Rc = XmitFrameSG( - pAC, - &pAC->TxPort[pNet->PortNr][TX_PRIO_LOW], - skb); - else - Rc = XmitFrameSG( - pAC, - &pAC->TxPort[pAC->ActivePort][TX_PRIO_LOW], - skb); - } - - /* Transmitter out of resources? */ - if (Rc <= 0) { - netif_stop_queue(dev); - } - - /* If not taken, give buffer ownership back to the - * queueing layer. - */ - if (Rc < 0) - return (1); - - dev->trans_start = jiffies; - return (0); -} /* SkGeXmit */ - - -/***************************************************************************** - * - * XmitFrame - fill one socket buffer into the transmit ring - * - * Description: - * This function puts a message into the transmit descriptor ring - * if there is a descriptors left. - * Linux skb's consist of only one continuous buffer. - * The first step locks the ring. It is held locked - * all time to avoid problems with SWITCH_../PORT_RESET. - * Then the descriptoris allocated. - * The second part is linking the buffer to the descriptor. - * At the very last, the Control field of the descriptor - * is made valid for the BMU and a start TX command is given - * if necessary. - * - * Returns: - * > 0 - on succes: the number of bytes in the message - * = 0 - on resource shortage: this frame sent or dropped, now - * the ring is full ( -> set tbusy) - * < 0 - on failure: other problems ( -> return failure to upper layers) - */ -static int XmitFrame( -SK_AC *pAC, /* pointer to adapter context */ -TX_PORT *pTxPort, /* pointer to struct of port to send to */ -struct sk_buff *pMessage) /* pointer to send-message */ -{ - TXD *pTxd; /* the rxd to fill */ - TXD *pOldTxd; - unsigned long Flags; - SK_U64 PhysAddr; - int BytesSend = pMessage->len; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_TX_PROGRESS, ("X")); - - spin_lock_irqsave(&pTxPort->TxDesRingLock, Flags); -#ifndef USE_TX_COMPLETE - FreeTxDescriptors(pAC, pTxPort); -#endif - if (pTxPort->TxdRingFree == 0) { - /* - ** no enough free descriptors in ring at the moment. - ** Maybe free'ing some old one help? - */ - FreeTxDescriptors(pAC, pTxPort); - if (pTxPort->TxdRingFree == 0) { - spin_unlock_irqrestore(&pTxPort->TxDesRingLock, Flags); - SK_PNMI_CNT_NO_TX_BUF(pAC, pTxPort->PortIndex); - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_TX_PROGRESS, - ("XmitFrame failed\n")); - /* - ** the desired message can not be sent - ** Because tbusy seems to be set, the message - ** should not be freed here. It will be used - ** by the scheduler of the ethernet handler - */ - return (-1); - } - } - - /* - ** If the passed socket buffer is of smaller MTU-size than 60, - ** copy everything into new buffer and fill all bytes between - ** the original packet end and the new packet end of 60 with 0x00. - ** This is to resolve faulty padding by the HW with 0xaa bytes. - */ - if (BytesSend < C_LEN_ETHERNET_MINSIZE) { - if (skb_padto(pMessage, C_LEN_ETHERNET_MINSIZE)) { - spin_unlock_irqrestore(&pTxPort->TxDesRingLock, Flags); - return 0; - } - pMessage->len = C_LEN_ETHERNET_MINSIZE; - } - - /* - ** advance head counter behind descriptor needed for this frame, - ** so that needed descriptor is reserved from that on. The next - ** action will be to add the passed buffer to the TX-descriptor - */ - pTxd = pTxPort->pTxdRingHead; - pTxPort->pTxdRingHead = pTxd->pNextTxd; - pTxPort->TxdRingFree--; - -#ifdef SK_DUMP_TX - DumpMsg(pMessage, "XmitFrame"); -#endif - - /* - ** First step is to map the data to be sent via the adapter onto - ** the DMA memory. Kernel 2.2 uses virt_to_bus(), but kernels 2.4 - ** and 2.6 need to use pci_map_page() for that mapping. - */ - PhysAddr = (SK_U64) pci_map_page(pAC->PciDev, - virt_to_page(pMessage->data), - ((unsigned long) pMessage->data & ~PAGE_MASK), - pMessage->len, - PCI_DMA_TODEVICE); - pTxd->VDataLow = (SK_U32) (PhysAddr & 0xffffffff); - pTxd->VDataHigh = (SK_U32) (PhysAddr >> 32); - pTxd->pMBuf = pMessage; - - if (pMessage->ip_summed == CHECKSUM_PARTIAL) { - u16 hdrlen = skb_transport_offset(pMessage); - u16 offset = hdrlen + pMessage->csum_offset; - - if ((ipip_hdr(pMessage)->protocol == IPPROTO_UDP) && - (pAC->GIni.GIChipRev == 0) && - (pAC->GIni.GIChipId == CHIP_ID_YUKON)) { - pTxd->TBControl = BMU_TCP_CHECK; - } else { - pTxd->TBControl = BMU_UDP_CHECK; - } - - pTxd->TcpSumOfs = 0; - pTxd->TcpSumSt = hdrlen; - pTxd->TcpSumWr = offset; - - pTxd->TBControl |= BMU_OWN | BMU_STF | - BMU_SW | BMU_EOF | -#ifdef USE_TX_COMPLETE - BMU_IRQ_EOF | -#endif - pMessage->len; - } else { - pTxd->TBControl = BMU_OWN | BMU_STF | BMU_CHECK | - BMU_SW | BMU_EOF | -#ifdef USE_TX_COMPLETE - BMU_IRQ_EOF | -#endif - pMessage->len; - } - - /* - ** If previous descriptor already done, give TX start cmd - */ - pOldTxd = xchg(&pTxPort->pTxdRingPrev, pTxd); - if ((pOldTxd->TBControl & BMU_OWN) == 0) { - SK_OUT8(pTxPort->HwAddr, Q_CSR, CSR_START); - } - - /* - ** after releasing the lock, the skb may immediately be free'd - */ - spin_unlock_irqrestore(&pTxPort->TxDesRingLock, Flags); - if (pTxPort->TxdRingFree != 0) { - return (BytesSend); - } else { - return (0); - } - -} /* XmitFrame */ - -/***************************************************************************** - * - * XmitFrameSG - fill one socket buffer into the transmit ring - * (use SG and TCP/UDP hardware checksumming) - * - * Description: - * This function puts a message into the transmit descriptor ring - * if there is a descriptors left. - * - * Returns: - * > 0 - on succes: the number of bytes in the message - * = 0 - on resource shortage: this frame sent or dropped, now - * the ring is full ( -> set tbusy) - * < 0 - on failure: other problems ( -> return failure to upper layers) - */ -static int XmitFrameSG( -SK_AC *pAC, /* pointer to adapter context */ -TX_PORT *pTxPort, /* pointer to struct of port to send to */ -struct sk_buff *pMessage) /* pointer to send-message */ -{ - - TXD *pTxd; - TXD *pTxdFst; - TXD *pTxdLst; - int CurrFrag; - int BytesSend; - skb_frag_t *sk_frag; - SK_U64 PhysAddr; - unsigned long Flags; - SK_U32 Control; - - spin_lock_irqsave(&pTxPort->TxDesRingLock, Flags); -#ifndef USE_TX_COMPLETE - FreeTxDescriptors(pAC, pTxPort); -#endif - if ((skb_shinfo(pMessage)->nr_frags +1) > pTxPort->TxdRingFree) { - FreeTxDescriptors(pAC, pTxPort); - if ((skb_shinfo(pMessage)->nr_frags + 1) > pTxPort->TxdRingFree) { - spin_unlock_irqrestore(&pTxPort->TxDesRingLock, Flags); - SK_PNMI_CNT_NO_TX_BUF(pAC, pTxPort->PortIndex); - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_TX_PROGRESS, - ("XmitFrameSG failed - Ring full\n")); - /* this message can not be sent now */ - return(-1); - } - } - - pTxd = pTxPort->pTxdRingHead; - pTxdFst = pTxd; - pTxdLst = pTxd; - BytesSend = 0; - - /* - ** Map the first fragment (header) into the DMA-space - */ - PhysAddr = (SK_U64) pci_map_page(pAC->PciDev, - virt_to_page(pMessage->data), - ((unsigned long) pMessage->data & ~PAGE_MASK), - skb_headlen(pMessage), - PCI_DMA_TODEVICE); - - pTxd->VDataLow = (SK_U32) (PhysAddr & 0xffffffff); - pTxd->VDataHigh = (SK_U32) (PhysAddr >> 32); - - /* - ** Does the HW need to evaluate checksum for TCP or UDP packets? - */ - if (pMessage->ip_summed == CHECKSUM_PARTIAL) { - u16 hdrlen = skb_transport_offset(pMessage); - u16 offset = hdrlen + pMessage->csum_offset; - - Control = BMU_STFWD; - - /* - ** We have to use the opcode for tcp here, because the - ** opcode for udp is not working in the hardware yet - ** (Revision 2.0) - */ - if ((ipip_hdr(pMessage)->protocol == IPPROTO_UDP) && - (pAC->GIni.GIChipRev == 0) && - (pAC->GIni.GIChipId == CHIP_ID_YUKON)) { - Control |= BMU_TCP_CHECK; - } else { - Control |= BMU_UDP_CHECK; - } - - pTxd->TcpSumOfs = 0; - pTxd->TcpSumSt = hdrlen; - pTxd->TcpSumWr = offset; - } else - Control = BMU_CHECK | BMU_SW; - - pTxd->TBControl = BMU_STF | Control | skb_headlen(pMessage); - - pTxd = pTxd->pNextTxd; - pTxPort->TxdRingFree--; - BytesSend += skb_headlen(pMessage); - - /* - ** Browse over all SG fragments and map each of them into the DMA space - */ - for (CurrFrag = 0; CurrFrag < skb_shinfo(pMessage)->nr_frags; CurrFrag++) { - sk_frag = &skb_shinfo(pMessage)->frags[CurrFrag]; - /* - ** we already have the proper value in entry - */ - PhysAddr = (SK_U64) pci_map_page(pAC->PciDev, - sk_frag->page, - sk_frag->page_offset, - sk_frag->size, - PCI_DMA_TODEVICE); - - pTxd->VDataLow = (SK_U32) (PhysAddr & 0xffffffff); - pTxd->VDataHigh = (SK_U32) (PhysAddr >> 32); - pTxd->pMBuf = pMessage; - - pTxd->TBControl = Control | BMU_OWN | sk_frag->size; - - /* - ** Do we have the last fragment? - */ - if( (CurrFrag+1) == skb_shinfo(pMessage)->nr_frags ) { -#ifdef USE_TX_COMPLETE - pTxd->TBControl |= BMU_EOF | BMU_IRQ_EOF; -#else - pTxd->TBControl |= BMU_EOF; -#endif - pTxdFst->TBControl |= BMU_OWN | BMU_SW; - } - pTxdLst = pTxd; - pTxd = pTxd->pNextTxd; - pTxPort->TxdRingFree--; - BytesSend += sk_frag->size; - } - - /* - ** If previous descriptor already done, give TX start cmd - */ - if ((pTxPort->pTxdRingPrev->TBControl & BMU_OWN) == 0) { - SK_OUT8(pTxPort->HwAddr, Q_CSR, CSR_START); - } - - pTxPort->pTxdRingPrev = pTxdLst; - pTxPort->pTxdRingHead = pTxd; - - spin_unlock_irqrestore(&pTxPort->TxDesRingLock, Flags); - - if (pTxPort->TxdRingFree > 0) { - return (BytesSend); - } else { - return (0); - } -} - -/***************************************************************************** - * - * FreeTxDescriptors - release descriptors from the descriptor ring - * - * Description: - * This function releases descriptors from a transmit ring if they - * have been sent by the BMU. - * If a descriptors is sent, it can be freed and the message can - * be freed, too. - * The SOFTWARE controllable bit is used to prevent running around a - * completely free ring for ever. If this bit is no set in the - * frame (by XmitFrame), this frame has never been sent or is - * already freed. - * The Tx descriptor ring lock must be held while calling this function !!! - * - * Returns: - * none - */ -static void FreeTxDescriptors( -SK_AC *pAC, /* pointer to the adapter context */ -TX_PORT *pTxPort) /* pointer to destination port structure */ -{ -TXD *pTxd; /* pointer to the checked descriptor */ -TXD *pNewTail; /* pointer to 'end' of the ring */ -SK_U32 Control; /* TBControl field of descriptor */ -SK_U64 PhysAddr; /* address of DMA mapping */ - - pNewTail = pTxPort->pTxdRingTail; - pTxd = pNewTail; - /* - ** loop forever; exits if BMU_SW bit not set in start frame - ** or BMU_OWN bit set in any frame - */ - while (1) { - Control = pTxd->TBControl; - if ((Control & BMU_SW) == 0) { - /* - ** software controllable bit is set in first - ** fragment when given to BMU. Not set means that - ** this fragment was never sent or is already - ** freed ( -> ring completely free now). - */ - pTxPort->pTxdRingTail = pTxd; - netif_wake_queue(pAC->dev[pTxPort->PortIndex]); - return; - } - if (Control & BMU_OWN) { - pTxPort->pTxdRingTail = pTxd; - if (pTxPort->TxdRingFree > 0) { - netif_wake_queue(pAC->dev[pTxPort->PortIndex]); - } - return; - } - - /* - ** release the DMA mapping, because until not unmapped - ** this buffer is considered being under control of the - ** adapter card! - */ - PhysAddr = ((SK_U64) pTxd->VDataHigh) << (SK_U64) 32; - PhysAddr |= (SK_U64) pTxd->VDataLow; - pci_unmap_page(pAC->PciDev, PhysAddr, - pTxd->pMBuf->len, - PCI_DMA_TODEVICE); - - if (Control & BMU_EOF) - DEV_KFREE_SKB_ANY(pTxd->pMBuf); /* free message */ - - pTxPort->TxdRingFree++; - pTxd->TBControl &= ~BMU_SW; - pTxd = pTxd->pNextTxd; /* point behind fragment with EOF */ - } /* while(forever) */ -} /* FreeTxDescriptors */ - -/***************************************************************************** - * - * FillRxRing - fill the receive ring with valid descriptors - * - * Description: - * This function fills the receive ring descriptors with data - * segments and makes them valid for the BMU. - * The active ring is filled completely, if possible. - * The non-active ring is filled only partial to save memory. - * - * Description of rx ring structure: - * head - points to the descriptor which will be used next by the BMU - * tail - points to the next descriptor to give to the BMU - * - * Returns: N/A - */ -static void FillRxRing( -SK_AC *pAC, /* pointer to the adapter context */ -RX_PORT *pRxPort) /* ptr to port struct for which the ring - should be filled */ -{ -unsigned long Flags; - - spin_lock_irqsave(&pRxPort->RxDesRingLock, Flags); - while (pRxPort->RxdRingFree > pRxPort->RxFillLimit) { - if(!FillRxDescriptor(pAC, pRxPort)) - break; - } - spin_unlock_irqrestore(&pRxPort->RxDesRingLock, Flags); -} /* FillRxRing */ - - -/***************************************************************************** - * - * FillRxDescriptor - fill one buffer into the receive ring - * - * Description: - * The function allocates a new receive buffer and - * puts it into the next descriptor. - * - * Returns: - * SK_TRUE - a buffer was added to the ring - * SK_FALSE - a buffer could not be added - */ -static SK_BOOL FillRxDescriptor( -SK_AC *pAC, /* pointer to the adapter context struct */ -RX_PORT *pRxPort) /* ptr to port struct of ring to fill */ -{ -struct sk_buff *pMsgBlock; /* pointer to a new message block */ -RXD *pRxd; /* the rxd to fill */ -SK_U16 Length; /* data fragment length */ -SK_U64 PhysAddr; /* physical address of a rx buffer */ - - pMsgBlock = alloc_skb(pAC->RxBufSize, GFP_ATOMIC); - if (pMsgBlock == NULL) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_ENTRY, - ("%s: Allocation of rx buffer failed !\n", - pAC->dev[pRxPort->PortIndex]->name)); - SK_PNMI_CNT_NO_RX_BUF(pAC, pRxPort->PortIndex); - return(SK_FALSE); - } - skb_reserve(pMsgBlock, 2); /* to align IP frames */ - /* skb allocated ok, so add buffer */ - pRxd = pRxPort->pRxdRingTail; - pRxPort->pRxdRingTail = pRxd->pNextRxd; - pRxPort->RxdRingFree--; - Length = pAC->RxBufSize; - PhysAddr = (SK_U64) pci_map_page(pAC->PciDev, - virt_to_page(pMsgBlock->data), - ((unsigned long) pMsgBlock->data & - ~PAGE_MASK), - pAC->RxBufSize - 2, - PCI_DMA_FROMDEVICE); - - pRxd->VDataLow = (SK_U32) (PhysAddr & 0xffffffff); - pRxd->VDataHigh = (SK_U32) (PhysAddr >> 32); - pRxd->pMBuf = pMsgBlock; - pRxd->RBControl = BMU_OWN | - BMU_STF | - BMU_IRQ_EOF | - BMU_TCP_CHECK | - Length; - return (SK_TRUE); - -} /* FillRxDescriptor */ - - -/***************************************************************************** - * - * ReQueueRxBuffer - fill one buffer back into the receive ring - * - * Description: - * Fill a given buffer back into the rx ring. The buffer - * has been previously allocated and aligned, and its phys. - * address calculated, so this is no more necessary. - * - * Returns: N/A - */ -static void ReQueueRxBuffer( -SK_AC *pAC, /* pointer to the adapter context struct */ -RX_PORT *pRxPort, /* ptr to port struct of ring to fill */ -struct sk_buff *pMsg, /* pointer to the buffer */ -SK_U32 PhysHigh, /* phys address high dword */ -SK_U32 PhysLow) /* phys address low dword */ -{ -RXD *pRxd; /* the rxd to fill */ -SK_U16 Length; /* data fragment length */ - - pRxd = pRxPort->pRxdRingTail; - pRxPort->pRxdRingTail = pRxd->pNextRxd; - pRxPort->RxdRingFree--; - Length = pAC->RxBufSize; - - pRxd->VDataLow = PhysLow; - pRxd->VDataHigh = PhysHigh; - pRxd->pMBuf = pMsg; - pRxd->RBControl = BMU_OWN | - BMU_STF | - BMU_IRQ_EOF | - BMU_TCP_CHECK | - Length; - return; -} /* ReQueueRxBuffer */ - -/***************************************************************************** - * - * ReceiveIrq - handle a receive IRQ - * - * Description: - * This function is called when a receive IRQ is set. - * It walks the receive descriptor ring and sends up all - * frames that are complete. - * - * Returns: N/A - */ -static void ReceiveIrq( - SK_AC *pAC, /* pointer to adapter context */ - RX_PORT *pRxPort, /* pointer to receive port struct */ - SK_BOOL SlowPathLock) /* indicates if SlowPathLock is needed */ -{ -RXD *pRxd; /* pointer to receive descriptors */ -SK_U32 Control; /* control field of descriptor */ -struct sk_buff *pMsg; /* pointer to message holding frame */ -struct sk_buff *pNewMsg; /* pointer to a new message for copying frame */ -int FrameLength; /* total length of received frame */ -SK_MBUF *pRlmtMbuf; /* ptr to a buffer for giving a frame to rlmt */ -SK_EVPARA EvPara; /* an event parameter union */ -unsigned long Flags; /* for spin lock */ -int PortIndex = pRxPort->PortIndex; -unsigned int Offset; -unsigned int NumBytes; -unsigned int ForRlmt; -SK_BOOL IsBc; -SK_BOOL IsMc; -SK_BOOL IsBadFrame; /* Bad frame */ - -SK_U32 FrameStat; -SK_U64 PhysAddr; - -rx_start: - /* do forever; exit if BMU_OWN found */ - for ( pRxd = pRxPort->pRxdRingHead ; - pRxPort->RxdRingFree < pAC->RxDescrPerRing ; - pRxd = pRxd->pNextRxd, - pRxPort->pRxdRingHead = pRxd, - pRxPort->RxdRingFree ++) { - - /* - * For a better understanding of this loop - * Go through every descriptor beginning at the head - * Please note: the ring might be completely received so the OWN bit - * set is not a good crirteria to leave that loop. - * Therefore the RingFree counter is used. - * On entry of this loop pRxd is a pointer to the Rxd that needs - * to be checked next. - */ - - Control = pRxd->RBControl; - - /* check if this descriptor is ready */ - if ((Control & BMU_OWN) != 0) { - /* this descriptor is not yet ready */ - /* This is the usual end of the loop */ - /* We don't need to start the ring again */ - FillRxRing(pAC, pRxPort); - return; - } - pAC->DynIrqModInfo.NbrProcessedDescr++; - - /* get length of frame and check it */ - FrameLength = Control & BMU_BBC; - if (FrameLength > pAC->RxBufSize) { - goto rx_failed; - } - - /* check for STF and EOF */ - if ((Control & (BMU_STF | BMU_EOF)) != (BMU_STF | BMU_EOF)) { - goto rx_failed; - } - - /* here we have a complete frame in the ring */ - pMsg = pRxd->pMBuf; - - FrameStat = pRxd->FrameStat; - - /* check for frame length mismatch */ -#define XMR_FS_LEN_SHIFT 18 -#define GMR_FS_LEN_SHIFT 16 - if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) { - if (FrameLength != (SK_U32) (FrameStat >> XMR_FS_LEN_SHIFT)) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_RX_PROGRESS, - ("skge: Frame length mismatch (%u/%u).\n", - FrameLength, - (SK_U32) (FrameStat >> XMR_FS_LEN_SHIFT))); - goto rx_failed; - } - } - else { - if (FrameLength != (SK_U32) (FrameStat >> GMR_FS_LEN_SHIFT)) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_RX_PROGRESS, - ("skge: Frame length mismatch (%u/%u).\n", - FrameLength, - (SK_U32) (FrameStat >> XMR_FS_LEN_SHIFT))); - goto rx_failed; - } - } - - /* Set Rx Status */ - if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) { - IsBc = (FrameStat & XMR_FS_BC) != 0; - IsMc = (FrameStat & XMR_FS_MC) != 0; - IsBadFrame = (FrameStat & - (XMR_FS_ANY_ERR | XMR_FS_2L_VLAN)) != 0; - } else { - IsBc = (FrameStat & GMR_FS_BC) != 0; - IsMc = (FrameStat & GMR_FS_MC) != 0; - IsBadFrame = (((FrameStat & GMR_FS_ANY_ERR) != 0) || - ((FrameStat & GMR_FS_RX_OK) == 0)); - } - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, 0, - ("Received frame of length %d on port %d\n", - FrameLength, PortIndex)); - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, 0, - ("Number of free rx descriptors: %d\n", - pRxPort->RxdRingFree)); -/* DumpMsg(pMsg, "Rx"); */ - - if ((Control & BMU_STAT_VAL) != BMU_STAT_VAL || (IsBadFrame)) { -#if 0 - (FrameStat & (XMR_FS_ANY_ERR | XMR_FS_2L_VLAN)) != 0) { -#endif - /* there is a receive error in this frame */ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_RX_PROGRESS, - ("skge: Error in received frame, dropped!\n" - "Control: %x\nRxStat: %x\n", - Control, FrameStat)); - - ReQueueRxBuffer(pAC, pRxPort, pMsg, - pRxd->VDataHigh, pRxd->VDataLow); - - continue; - } - - /* - * if short frame then copy data to reduce memory waste - */ - if ((FrameLength < SK_COPY_THRESHOLD) && - ((pNewMsg = alloc_skb(FrameLength+2, GFP_ATOMIC)) != NULL)) { - /* - * Short frame detected and allocation successfull - */ - /* use new skb and copy data */ - skb_reserve(pNewMsg, 2); - skb_put(pNewMsg, FrameLength); - PhysAddr = ((SK_U64) pRxd->VDataHigh) << (SK_U64)32; - PhysAddr |= (SK_U64) pRxd->VDataLow; - - pci_dma_sync_single_for_cpu(pAC->PciDev, - (dma_addr_t) PhysAddr, - FrameLength, - PCI_DMA_FROMDEVICE); - skb_copy_to_linear_data(pNewMsg, pMsg, FrameLength); - - pci_dma_sync_single_for_device(pAC->PciDev, - (dma_addr_t) PhysAddr, - FrameLength, - PCI_DMA_FROMDEVICE); - ReQueueRxBuffer(pAC, pRxPort, pMsg, - pRxd->VDataHigh, pRxd->VDataLow); - - pMsg = pNewMsg; - - } - else { - /* - * if large frame, or SKB allocation failed, pass - * the SKB directly to the networking - */ - - PhysAddr = ((SK_U64) pRxd->VDataHigh) << (SK_U64)32; - PhysAddr |= (SK_U64) pRxd->VDataLow; - - /* release the DMA mapping */ - pci_unmap_single(pAC->PciDev, - PhysAddr, - pAC->RxBufSize - 2, - PCI_DMA_FROMDEVICE); - - /* set length in message */ - skb_put(pMsg, FrameLength); - } /* frame > SK_COPY_TRESHOLD */ - -#ifdef USE_SK_RX_CHECKSUM - pMsg->csum = pRxd->TcpSums & 0xffff; - pMsg->ip_summed = CHECKSUM_COMPLETE; -#else - pMsg->ip_summed = CHECKSUM_NONE; -#endif - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, 1,("V")); - ForRlmt = SK_RLMT_RX_PROTOCOL; -#if 0 - IsBc = (FrameStat & XMR_FS_BC)==XMR_FS_BC; -#endif - SK_RLMT_PRE_LOOKAHEAD(pAC, PortIndex, FrameLength, - IsBc, &Offset, &NumBytes); - if (NumBytes != 0) { -#if 0 - IsMc = (FrameStat & XMR_FS_MC)==XMR_FS_MC; -#endif - SK_RLMT_LOOKAHEAD(pAC, PortIndex, - &pMsg->data[Offset], - IsBc, IsMc, &ForRlmt); - } - if (ForRlmt == SK_RLMT_RX_PROTOCOL) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, 1,("W")); - /* send up only frames from active port */ - if ((PortIndex == pAC->ActivePort) || - (pAC->RlmtNets == 2)) { - /* frame for upper layer */ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, 1,("U")); -#ifdef xDEBUG - DumpMsg(pMsg, "Rx"); -#endif - SK_PNMI_CNT_RX_OCTETS_DELIVERED(pAC, - FrameLength, pRxPort->PortIndex); - - pMsg->protocol = eth_type_trans(pMsg, - pAC->dev[pRxPort->PortIndex]); - netif_rx(pMsg); - pAC->dev[pRxPort->PortIndex]->last_rx = jiffies; - } - else { - /* drop frame */ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_RX_PROGRESS, - ("D")); - DEV_KFREE_SKB(pMsg); - } - - } /* if not for rlmt */ - else { - /* packet for rlmt */ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_RX_PROGRESS, ("R")); - pRlmtMbuf = SkDrvAllocRlmtMbuf(pAC, - pAC->IoBase, FrameLength); - if (pRlmtMbuf != NULL) { - pRlmtMbuf->pNext = NULL; - pRlmtMbuf->Length = FrameLength; - pRlmtMbuf->PortIdx = PortIndex; - EvPara.pParaPtr = pRlmtMbuf; - memcpy((char*)(pRlmtMbuf->pData), - (char*)(pMsg->data), - FrameLength); - - /* SlowPathLock needed? */ - if (SlowPathLock == SK_TRUE) { - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - SkEventQueue(pAC, SKGE_RLMT, - SK_RLMT_PACKET_RECEIVED, - EvPara); - pAC->CheckQueue = SK_TRUE; - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - } else { - SkEventQueue(pAC, SKGE_RLMT, - SK_RLMT_PACKET_RECEIVED, - EvPara); - pAC->CheckQueue = SK_TRUE; - } - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, - SK_DBGCAT_DRV_RX_PROGRESS, - ("Q")); - } - if ((pAC->dev[pRxPort->PortIndex]->flags & - (IFF_PROMISC | IFF_ALLMULTI)) != 0 || - (ForRlmt & SK_RLMT_RX_PROTOCOL) == - SK_RLMT_RX_PROTOCOL) { - pMsg->protocol = eth_type_trans(pMsg, - pAC->dev[pRxPort->PortIndex]); - netif_rx(pMsg); - pAC->dev[pRxPort->PortIndex]->last_rx = jiffies; - } - else { - DEV_KFREE_SKB(pMsg); - } - - } /* if packet for rlmt */ - } /* for ... scanning the RXD ring */ - - /* RXD ring is empty -> fill and restart */ - FillRxRing(pAC, pRxPort); - /* do not start if called from Close */ - if (pAC->BoardLevel > SK_INIT_DATA) { - ClearAndStartRx(pAC, PortIndex); - } - return; - -rx_failed: - /* remove error frame */ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ERROR, - ("Schrottdescriptor, length: 0x%x\n", FrameLength)); - - /* release the DMA mapping */ - - PhysAddr = ((SK_U64) pRxd->VDataHigh) << (SK_U64)32; - PhysAddr |= (SK_U64) pRxd->VDataLow; - pci_unmap_page(pAC->PciDev, - PhysAddr, - pAC->RxBufSize - 2, - PCI_DMA_FROMDEVICE); - DEV_KFREE_SKB_IRQ(pRxd->pMBuf); - pRxd->pMBuf = NULL; - pRxPort->RxdRingFree++; - pRxPort->pRxdRingHead = pRxd->pNextRxd; - goto rx_start; - -} /* ReceiveIrq */ - - -/***************************************************************************** - * - * ClearAndStartRx - give a start receive command to BMU, clear IRQ - * - * Description: - * This function sends a start command and a clear interrupt - * command for one receive queue to the BMU. - * - * Returns: N/A - * none - */ -static void ClearAndStartRx( -SK_AC *pAC, /* pointer to the adapter context */ -int PortIndex) /* index of the receive port (XMAC) */ -{ - SK_OUT8(pAC->IoBase, - RxQueueAddr[PortIndex]+Q_CSR, - CSR_START | CSR_IRQ_CL_F); -} /* ClearAndStartRx */ - - -/***************************************************************************** - * - * ClearTxIrq - give a clear transmit IRQ command to BMU - * - * Description: - * This function sends a clear tx IRQ command for one - * transmit queue to the BMU. - * - * Returns: N/A - */ -static void ClearTxIrq( -SK_AC *pAC, /* pointer to the adapter context */ -int PortIndex, /* index of the transmit port (XMAC) */ -int Prio) /* priority or normal queue */ -{ - SK_OUT8(pAC->IoBase, - TxQueueAddr[PortIndex][Prio]+Q_CSR, - CSR_IRQ_CL_F); -} /* ClearTxIrq */ - - -/***************************************************************************** - * - * ClearRxRing - remove all buffers from the receive ring - * - * Description: - * This function removes all receive buffers from the ring. - * The receive BMU must be stopped before calling this function. - * - * Returns: N/A - */ -static void ClearRxRing( -SK_AC *pAC, /* pointer to adapter context */ -RX_PORT *pRxPort) /* pointer to rx port struct */ -{ -RXD *pRxd; /* pointer to the current descriptor */ -unsigned long Flags; -SK_U64 PhysAddr; - - if (pRxPort->RxdRingFree == pAC->RxDescrPerRing) { - return; - } - spin_lock_irqsave(&pRxPort->RxDesRingLock, Flags); - pRxd = pRxPort->pRxdRingHead; - do { - if (pRxd->pMBuf != NULL) { - - PhysAddr = ((SK_U64) pRxd->VDataHigh) << (SK_U64)32; - PhysAddr |= (SK_U64) pRxd->VDataLow; - pci_unmap_page(pAC->PciDev, - PhysAddr, - pAC->RxBufSize - 2, - PCI_DMA_FROMDEVICE); - DEV_KFREE_SKB(pRxd->pMBuf); - pRxd->pMBuf = NULL; - } - pRxd->RBControl &= BMU_OWN; - pRxd = pRxd->pNextRxd; - pRxPort->RxdRingFree++; - } while (pRxd != pRxPort->pRxdRingTail); - pRxPort->pRxdRingTail = pRxPort->pRxdRingHead; - spin_unlock_irqrestore(&pRxPort->RxDesRingLock, Flags); -} /* ClearRxRing */ - -/***************************************************************************** - * - * ClearTxRing - remove all buffers from the transmit ring - * - * Description: - * This function removes all transmit buffers from the ring. - * The transmit BMU must be stopped before calling this function - * and transmitting at the upper level must be disabled. - * The BMU own bit of all descriptors is cleared, the rest is - * done by calling FreeTxDescriptors. - * - * Returns: N/A - */ -static void ClearTxRing( -SK_AC *pAC, /* pointer to adapter context */ -TX_PORT *pTxPort) /* pointer to tx prt struct */ -{ -TXD *pTxd; /* pointer to the current descriptor */ -int i; -unsigned long Flags; - - spin_lock_irqsave(&pTxPort->TxDesRingLock, Flags); - pTxd = pTxPort->pTxdRingHead; - for (i=0; i<pAC->TxDescrPerRing; i++) { - pTxd->TBControl &= ~BMU_OWN; - pTxd = pTxd->pNextTxd; - } - FreeTxDescriptors(pAC, pTxPort); - spin_unlock_irqrestore(&pTxPort->TxDesRingLock, Flags); -} /* ClearTxRing */ - -/***************************************************************************** - * - * SkGeSetMacAddr - Set the hardware MAC address - * - * Description: - * This function sets the MAC address used by the adapter. - * - * Returns: - * 0, if everything is ok - * !=0, on error - */ -static int SkGeSetMacAddr(struct SK_NET_DEVICE *dev, void *p) -{ - -DEV_NET *pNet = netdev_priv(dev); -SK_AC *pAC = pNet->pAC; - -struct sockaddr *addr = p; -unsigned long Flags; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeSetMacAddr starts now...\n")); - if(netif_running(dev)) - return -EBUSY; - - memcpy(dev->dev_addr, addr->sa_data,dev->addr_len); - - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - - if (pAC->RlmtNets == 2) - SkAddrOverride(pAC, pAC->IoBase, pNet->NetNr, - (SK_MAC_ADDR*)dev->dev_addr, SK_ADDR_VIRTUAL_ADDRESS); - else - SkAddrOverride(pAC, pAC->IoBase, pAC->ActivePort, - (SK_MAC_ADDR*)dev->dev_addr, SK_ADDR_VIRTUAL_ADDRESS); - - - - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - return 0; -} /* SkGeSetMacAddr */ - - -/***************************************************************************** - * - * SkGeSetRxMode - set receive mode - * - * Description: - * This function sets the receive mode of an adapter. The adapter - * supports promiscuous mode, allmulticast mode and a number of - * multicast addresses. If more multicast addresses the available - * are selected, a hash function in the hardware is used. - * - * Returns: - * 0, if everything is ok - * !=0, on error - */ -static void SkGeSetRxMode(struct SK_NET_DEVICE *dev) -{ - -DEV_NET *pNet; -SK_AC *pAC; - -struct dev_mc_list *pMcList; -int i; -int PortIdx; -unsigned long Flags; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeSetRxMode starts now... ")); - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - if (pAC->RlmtNets == 1) - PortIdx = pAC->ActivePort; - else - PortIdx = pNet->NetNr; - - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - if (dev->flags & IFF_PROMISC) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("PROMISCUOUS mode\n")); - SkAddrPromiscuousChange(pAC, pAC->IoBase, PortIdx, - SK_PROM_MODE_LLC); - } else if (dev->flags & IFF_ALLMULTI) { - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("ALLMULTI mode\n")); - SkAddrPromiscuousChange(pAC, pAC->IoBase, PortIdx, - SK_PROM_MODE_ALL_MC); - } else { - SkAddrPromiscuousChange(pAC, pAC->IoBase, PortIdx, - SK_PROM_MODE_NONE); - SkAddrMcClear(pAC, pAC->IoBase, PortIdx, 0); - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("Number of MC entries: %d ", dev->mc_count)); - - pMcList = dev->mc_list; - for (i=0; i<dev->mc_count; i++, pMcList = pMcList->next) { - SkAddrMcAdd(pAC, pAC->IoBase, PortIdx, - (SK_MAC_ADDR*)pMcList->dmi_addr, 0); - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_MCA, - ("%02x:%02x:%02x:%02x:%02x:%02x\n", - pMcList->dmi_addr[0], - pMcList->dmi_addr[1], - pMcList->dmi_addr[2], - pMcList->dmi_addr[3], - pMcList->dmi_addr[4], - pMcList->dmi_addr[5])); - } - SkAddrMcUpdate(pAC, pAC->IoBase, PortIdx); - } - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - - return; -} /* SkGeSetRxMode */ - - -/***************************************************************************** - * - * SkGeChangeMtu - set the MTU to another value - * - * Description: - * This function sets is called whenever the MTU size is changed - * (ifconfig mtu xxx dev ethX). If the MTU is bigger than standard - * ethernet MTU size, long frame support is activated. - * - * Returns: - * 0, if everything is ok - * !=0, on error - */ -static int SkGeChangeMtu(struct SK_NET_DEVICE *dev, int NewMtu) -{ -DEV_NET *pNet; -struct net_device *pOtherDev; -SK_AC *pAC; -unsigned long Flags; -int i; -SK_EVPARA EvPara; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeChangeMtu starts now...\n")); - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - - if ((NewMtu < 68) || (NewMtu > SK_JUMBO_MTU)) { - return -EINVAL; - } - - if(pAC->BoardLevel != SK_INIT_RUN) { - return -EINVAL; - } - -#ifdef SK_DIAG_SUPPORT - if (pAC->DiagModeActive == DIAG_ACTIVE) { - if (pAC->DiagFlowCtrl == SK_FALSE) { - return -1; /* still in use, deny any actions of MTU */ - } else { - pAC->DiagFlowCtrl = SK_FALSE; - } - } -#endif - - pOtherDev = pAC->dev[1 - pNet->NetNr]; - - if ( netif_running(pOtherDev) && (pOtherDev->mtu > 1500) - && (NewMtu <= 1500)) - return 0; - - pAC->RxBufSize = NewMtu + 32; - dev->mtu = NewMtu; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("New MTU: %d\n", NewMtu)); - - /* - ** Prevent any reconfiguration while changing the MTU - ** by disabling any interrupts - */ - SK_OUT32(pAC->IoBase, B0_IMSK, 0); - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - - /* - ** Notify RLMT that any ports are to be stopped - */ - EvPara.Para32[0] = 0; - EvPara.Para32[1] = -1; - if ((pAC->GIni.GIMacsFound == 2 ) && (pAC->RlmtNets == 2)) { - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_STOP, EvPara); - EvPara.Para32[0] = 1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_STOP, EvPara); - } else { - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_STOP, EvPara); - } - - /* - ** After calling the SkEventDispatcher(), RLMT is aware about - ** the stopped ports -> configuration can take place! - */ - SkEventDispatcher(pAC, pAC->IoBase); - - for (i=0; i<pAC->GIni.GIMacsFound; i++) { - spin_lock(&pAC->TxPort[i][TX_PRIO_LOW].TxDesRingLock); - netif_stop_queue(pAC->dev[i]); - - } - - /* - ** Depending on the desired MTU size change, a different number of - ** RX buffers need to be allocated - */ - if (NewMtu > 1500) { - /* - ** Use less rx buffers - */ - for (i=0; i<pAC->GIni.GIMacsFound; i++) { - if ((pAC->GIni.GIMacsFound == 2 ) && (pAC->RlmtNets == 2)) { - pAC->RxPort[i].RxFillLimit = pAC->RxDescrPerRing - - (pAC->RxDescrPerRing / 4); - } else { - if (i == pAC->ActivePort) { - pAC->RxPort[i].RxFillLimit = pAC->RxDescrPerRing - - (pAC->RxDescrPerRing / 4); - } else { - pAC->RxPort[i].RxFillLimit = pAC->RxDescrPerRing - - (pAC->RxDescrPerRing / 10); - } - } - } - } else { - /* - ** Use the normal amount of rx buffers - */ - for (i=0; i<pAC->GIni.GIMacsFound; i++) { - if ((pAC->GIni.GIMacsFound == 2 ) && (pAC->RlmtNets == 2)) { - pAC->RxPort[i].RxFillLimit = 1; - } else { - if (i == pAC->ActivePort) { - pAC->RxPort[i].RxFillLimit = 1; - } else { - pAC->RxPort[i].RxFillLimit = pAC->RxDescrPerRing - - (pAC->RxDescrPerRing / 4); - } - } - } - } - - SkGeDeInit(pAC, pAC->IoBase); - - /* - ** enable/disable hardware support for long frames - */ - if (NewMtu > 1500) { -// pAC->JumboActivated = SK_TRUE; /* is never set back !!! */ - pAC->GIni.GIPortUsage = SK_JUMBO_LINK; - } else { - if ((pAC->GIni.GIMacsFound == 2 ) && (pAC->RlmtNets == 2)) { - pAC->GIni.GIPortUsage = SK_MUL_LINK; - } else { - pAC->GIni.GIPortUsage = SK_RED_LINK; - } - } - - SkGeInit( pAC, pAC->IoBase, SK_INIT_IO); - SkI2cInit( pAC, pAC->IoBase, SK_INIT_IO); - SkEventInit(pAC, pAC->IoBase, SK_INIT_IO); - SkPnmiInit( pAC, pAC->IoBase, SK_INIT_IO); - SkAddrInit( pAC, pAC->IoBase, SK_INIT_IO); - SkRlmtInit( pAC, pAC->IoBase, SK_INIT_IO); - SkTimerInit(pAC, pAC->IoBase, SK_INIT_IO); - - /* - ** tschilling: - ** Speed and others are set back to default in level 1 init! - */ - GetConfiguration(pAC); - - SkGeInit( pAC, pAC->IoBase, SK_INIT_RUN); - SkI2cInit( pAC, pAC->IoBase, SK_INIT_RUN); - SkEventInit(pAC, pAC->IoBase, SK_INIT_RUN); - SkPnmiInit( pAC, pAC->IoBase, SK_INIT_RUN); - SkAddrInit( pAC, pAC->IoBase, SK_INIT_RUN); - SkRlmtInit( pAC, pAC->IoBase, SK_INIT_RUN); - SkTimerInit(pAC, pAC->IoBase, SK_INIT_RUN); - - /* - ** clear and reinit the rx rings here - */ - for (i=0; i<pAC->GIni.GIMacsFound; i++) { - ReceiveIrq(pAC, &pAC->RxPort[i], SK_TRUE); - ClearRxRing(pAC, &pAC->RxPort[i]); - FillRxRing(pAC, &pAC->RxPort[i]); - - /* - ** Enable transmit descriptor polling - */ - SkGePollTxD(pAC, pAC->IoBase, i, SK_TRUE); - FillRxRing(pAC, &pAC->RxPort[i]); - }; - - SkGeYellowLED(pAC, pAC->IoBase, 1); - SkDimEnableModerationIfNeeded(pAC); - SkDimDisplayModerationSettings(pAC); - - netif_start_queue(pAC->dev[pNet->PortNr]); - for (i=pAC->GIni.GIMacsFound-1; i>=0; i--) { - spin_unlock(&pAC->TxPort[i][TX_PRIO_LOW].TxDesRingLock); - } - - /* - ** Enable Interrupts again - */ - SK_OUT32(pAC->IoBase, B0_IMSK, pAC->GIni.GIValIrqMask); - SK_OUT32(pAC->IoBase, B0_HWE_IMSK, IRQ_HWE_MASK); - - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_START, EvPara); - SkEventDispatcher(pAC, pAC->IoBase); - - /* - ** Notify RLMT about the changing and restarting one (or more) ports - */ - if ((pAC->GIni.GIMacsFound == 2 ) && (pAC->RlmtNets == 2)) { - EvPara.Para32[0] = pAC->RlmtNets; - EvPara.Para32[1] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_SET_NETS, EvPara); - EvPara.Para32[0] = pNet->PortNr; - EvPara.Para32[1] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_START, EvPara); - - if (netif_running(pOtherDev)) { - DEV_NET *pOtherNet = netdev_priv(pOtherDev); - EvPara.Para32[0] = pOtherNet->PortNr; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_START, EvPara); - } - } else { - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_START, EvPara); - } - - SkEventDispatcher(pAC, pAC->IoBase); - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - - /* - ** While testing this driver with latest kernel 2.5 (2.5.70), it - ** seems as if upper layers have a problem to handle a successful - ** return value of '0'. If such a zero is returned, the complete - ** system hangs for several minutes (!), which is in acceptable. - ** - ** Currently it is not clear, what the exact reason for this problem - ** is. The implemented workaround for 2.5 is to return the desired - ** new MTU size if all needed changes for the new MTU size where - ** performed. In kernels 2.2 and 2.4, a zero value is returned, - ** which indicates the successful change of the mtu-size. - */ - return NewMtu; - -} /* SkGeChangeMtu */ - - -/***************************************************************************** - * - * SkGeStats - return ethernet device statistics - * - * Description: - * This function return statistic data about the ethernet device - * to the operating system. - * - * Returns: - * pointer to the statistic structure. - */ -static struct net_device_stats *SkGeStats(struct SK_NET_DEVICE *dev) -{ -DEV_NET *pNet = netdev_priv(dev); -SK_AC *pAC = pNet->pAC; -SK_PNMI_STRUCT_DATA *pPnmiStruct; /* structure for all Pnmi-Data */ -SK_PNMI_STAT *pPnmiStat; /* pointer to virtual XMAC stat. data */ -SK_PNMI_CONF *pPnmiConf; /* pointer to virtual link config. */ -unsigned int Size; /* size of pnmi struct */ -unsigned long Flags; /* for spin lock */ - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeStats starts now...\n")); - pPnmiStruct = &pAC->PnmiStruct; - -#ifdef SK_DIAG_SUPPORT - if ((pAC->DiagModeActive == DIAG_NOTACTIVE) && - (pAC->BoardLevel == SK_INIT_RUN)) { -#endif - SK_MEMSET(pPnmiStruct, 0, sizeof(SK_PNMI_STRUCT_DATA)); - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - Size = SK_PNMI_STRUCT_SIZE; - SkPnmiGetStruct(pAC, pAC->IoBase, pPnmiStruct, &Size, pNet->NetNr); - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); -#ifdef SK_DIAG_SUPPORT - } -#endif - - pPnmiStat = &pPnmiStruct->Stat[0]; - pPnmiConf = &pPnmiStruct->Conf[0]; - - pAC->stats.rx_packets = (SK_U32) pPnmiStruct->RxDeliveredCts & 0xFFFFFFFF; - pAC->stats.tx_packets = (SK_U32) pPnmiStat->StatTxOkCts & 0xFFFFFFFF; - pAC->stats.rx_bytes = (SK_U32) pPnmiStruct->RxOctetsDeliveredCts; - pAC->stats.tx_bytes = (SK_U32) pPnmiStat->StatTxOctetsOkCts; - - if (dev->mtu <= 1500) { - pAC->stats.rx_errors = (SK_U32) pPnmiStruct->InErrorsCts & 0xFFFFFFFF; - } else { - pAC->stats.rx_errors = (SK_U32) ((pPnmiStruct->InErrorsCts - - pPnmiStat->StatRxTooLongCts) & 0xFFFFFFFF); - } - - - if (pAC->GIni.GP[0].PhyType == SK_PHY_XMAC && pAC->HWRevision < 12) - pAC->stats.rx_errors = pAC->stats.rx_errors - pPnmiStat->StatRxShortsCts; - - pAC->stats.tx_errors = (SK_U32) pPnmiStat->StatTxSingleCollisionCts & 0xFFFFFFFF; - pAC->stats.rx_dropped = (SK_U32) pPnmiStruct->RxNoBufCts & 0xFFFFFFFF; - pAC->stats.tx_dropped = (SK_U32) pPnmiStruct->TxNoBufCts & 0xFFFFFFFF; - pAC->stats.multicast = (SK_U32) pPnmiStat->StatRxMulticastOkCts & 0xFFFFFFFF; - pAC->stats.collisions = (SK_U32) pPnmiStat->StatTxSingleCollisionCts & 0xFFFFFFFF; - - /* detailed rx_errors: */ - pAC->stats.rx_length_errors = (SK_U32) pPnmiStat->StatRxRuntCts & 0xFFFFFFFF; - pAC->stats.rx_over_errors = (SK_U32) pPnmiStat->StatRxFifoOverflowCts & 0xFFFFFFFF; - pAC->stats.rx_crc_errors = (SK_U32) pPnmiStat->StatRxFcsCts & 0xFFFFFFFF; - pAC->stats.rx_frame_errors = (SK_U32) pPnmiStat->StatRxFramingCts & 0xFFFFFFFF; - pAC->stats.rx_fifo_errors = (SK_U32) pPnmiStat->StatRxFifoOverflowCts & 0xFFFFFFFF; - pAC->stats.rx_missed_errors = (SK_U32) pPnmiStat->StatRxMissedCts & 0xFFFFFFFF; - - /* detailed tx_errors */ - pAC->stats.tx_aborted_errors = (SK_U32) 0; - pAC->stats.tx_carrier_errors = (SK_U32) pPnmiStat->StatTxCarrierCts & 0xFFFFFFFF; - pAC->stats.tx_fifo_errors = (SK_U32) pPnmiStat->StatTxFifoUnderrunCts & 0xFFFFFFFF; - pAC->stats.tx_heartbeat_errors = (SK_U32) pPnmiStat->StatTxCarrierCts & 0xFFFFFFFF; - pAC->stats.tx_window_errors = (SK_U32) 0; - - return(&pAC->stats); -} /* SkGeStats */ - -/* - * Basic MII register access - */ -static int SkGeMiiIoctl(struct net_device *dev, - struct mii_ioctl_data *data, int cmd) -{ - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - SK_IOC IoC = pAC->IoBase; - int Port = pNet->PortNr; - SK_GEPORT *pPrt = &pAC->GIni.GP[Port]; - unsigned long Flags; - int err = 0; - int reg = data->reg_num & 0x1f; - SK_U16 val = data->val_in; - - if (!netif_running(dev)) - return -ENODEV; /* Phy still in reset */ - - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - switch(cmd) { - case SIOCGMIIPHY: - data->phy_id = pPrt->PhyAddr; - - /* fallthru */ - case SIOCGMIIREG: - if (pAC->GIni.GIGenesis) - SkXmPhyRead(pAC, IoC, Port, reg, &val); - else - SkGmPhyRead(pAC, IoC, Port, reg, &val); - - data->val_out = val; - break; - - case SIOCSMIIREG: - if (!capable(CAP_NET_ADMIN)) - err = -EPERM; - - else if (pAC->GIni.GIGenesis) - SkXmPhyWrite(pAC, IoC, Port, reg, val); - else - SkGmPhyWrite(pAC, IoC, Port, reg, val); - break; - default: - err = -EOPNOTSUPP; - } - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - return err; -} - - -/***************************************************************************** - * - * SkGeIoctl - IO-control function - * - * Description: - * This function is called if an ioctl is issued on the device. - * There are three subfunction for reading, writing and test-writing - * the private MIB data structure (useful for SysKonnect-internal tools). - * - * Returns: - * 0, if everything is ok - * !=0, on error - */ -static int SkGeIoctl(struct SK_NET_DEVICE *dev, struct ifreq *rq, int cmd) -{ -DEV_NET *pNet; -SK_AC *pAC; -void *pMemBuf; -struct pci_dev *pdev = NULL; -SK_GE_IOCTL Ioctl; -unsigned int Err = 0; -int Size = 0; -int Ret = 0; -unsigned int Length = 0; -int HeaderLength = sizeof(SK_U32) + sizeof(SK_U32); - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeIoctl starts now...\n")); - - pNet = netdev_priv(dev); - pAC = pNet->pAC; - - if (cmd == SIOCGMIIPHY || cmd == SIOCSMIIREG || cmd == SIOCGMIIREG) - return SkGeMiiIoctl(dev, if_mii(rq), cmd); - - if(copy_from_user(&Ioctl, rq->ifr_data, sizeof(SK_GE_IOCTL))) { - return -EFAULT; - } - - switch(cmd) { - case SK_IOCTL_SETMIB: - case SK_IOCTL_PRESETMIB: - if (!capable(CAP_NET_ADMIN)) return -EPERM; - case SK_IOCTL_GETMIB: - if(copy_from_user(&pAC->PnmiStruct, Ioctl.pData, - Ioctl.Len<sizeof(pAC->PnmiStruct)? - Ioctl.Len : sizeof(pAC->PnmiStruct))) { - return -EFAULT; - } - Size = SkGeIocMib(pNet, Ioctl.Len, cmd); - if(copy_to_user(Ioctl.pData, &pAC->PnmiStruct, - Ioctl.Len<Size? Ioctl.Len : Size)) { - return -EFAULT; - } - Ioctl.Len = Size; - if(copy_to_user(rq->ifr_data, &Ioctl, sizeof(SK_GE_IOCTL))) { - return -EFAULT; - } - break; - case SK_IOCTL_GEN: - if (Ioctl.Len < (sizeof(pAC->PnmiStruct) + HeaderLength)) { - Length = Ioctl.Len; - } else { - Length = sizeof(pAC->PnmiStruct) + HeaderLength; - } - if (NULL == (pMemBuf = kmalloc(Length, GFP_KERNEL))) { - return -ENOMEM; - } - if(copy_from_user(pMemBuf, Ioctl.pData, Length)) { - Err = -EFAULT; - goto fault_gen; - } - if ((Ret = SkPnmiGenIoctl(pAC, pAC->IoBase, pMemBuf, &Length, 0)) < 0) { - Err = -EFAULT; - goto fault_gen; - } - if(copy_to_user(Ioctl.pData, pMemBuf, Length) ) { - Err = -EFAULT; - goto fault_gen; - } - Ioctl.Len = Length; - if(copy_to_user(rq->ifr_data, &Ioctl, sizeof(SK_GE_IOCTL))) { - Err = -EFAULT; - goto fault_gen; - } -fault_gen: - kfree(pMemBuf); /* cleanup everything */ - break; -#ifdef SK_DIAG_SUPPORT - case SK_IOCTL_DIAG: - if (!capable(CAP_NET_ADMIN)) return -EPERM; - if (Ioctl.Len < (sizeof(pAC->PnmiStruct) + HeaderLength)) { - Length = Ioctl.Len; - } else { - Length = sizeof(pAC->PnmiStruct) + HeaderLength; - } - if (NULL == (pMemBuf = kmalloc(Length, GFP_KERNEL))) { - return -ENOMEM; - } - if(copy_from_user(pMemBuf, Ioctl.pData, Length)) { - Err = -EFAULT; - goto fault_diag; - } - pdev = pAC->PciDev; - Length = 3 * sizeof(SK_U32); /* Error, Bus and Device */ - /* - ** While coding this new IOCTL interface, only a few lines of code - ** are to to be added. Therefore no dedicated function has been - ** added. If more functionality is added, a separate function - ** should be used... - */ - * ((SK_U32 *)pMemBuf) = 0; - * ((SK_U32 *)pMemBuf + 1) = pdev->bus->number; - * ((SK_U32 *)pMemBuf + 2) = ParseDeviceNbrFromSlotName(pci_name(pdev)); - if(copy_to_user(Ioctl.pData, pMemBuf, Length) ) { - Err = -EFAULT; - goto fault_diag; - } - Ioctl.Len = Length; - if(copy_to_user(rq->ifr_data, &Ioctl, sizeof(SK_GE_IOCTL))) { - Err = -EFAULT; - goto fault_diag; - } -fault_diag: - kfree(pMemBuf); /* cleanup everything */ - break; -#endif - default: - Err = -EOPNOTSUPP; - } - - return(Err); - -} /* SkGeIoctl */ - - -/***************************************************************************** - * - * SkGeIocMib - handle a GetMib, SetMib- or PresetMib-ioctl message - * - * Description: - * This function reads/writes the MIB data using PNMI (Private Network - * Management Interface). - * The destination for the data must be provided with the - * ioctl call and is given to the driver in the form of - * a user space address. - * Copying from the user-provided data area into kernel messages - * and back is done by copy_from_user and copy_to_user calls in - * SkGeIoctl. - * - * Returns: - * returned size from PNMI call - */ -static int SkGeIocMib( -DEV_NET *pNet, /* pointer to the adapter context */ -unsigned int Size, /* length of ioctl data */ -int mode) /* flag for set/preset */ -{ -unsigned long Flags; /* for spin lock */ -SK_AC *pAC; - - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("SkGeIocMib starts now...\n")); - pAC = pNet->pAC; - /* access MIB */ - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - switch(mode) { - case SK_IOCTL_GETMIB: - SkPnmiGetStruct(pAC, pAC->IoBase, &pAC->PnmiStruct, &Size, - pNet->NetNr); - break; - case SK_IOCTL_PRESETMIB: - SkPnmiPreSetStruct(pAC, pAC->IoBase, &pAC->PnmiStruct, &Size, - pNet->NetNr); - break; - case SK_IOCTL_SETMIB: - SkPnmiSetStruct(pAC, pAC->IoBase, &pAC->PnmiStruct, &Size, - pNet->NetNr); - break; - default: - break; - } - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_ENTRY, - ("MIB data access succeeded\n")); - return (Size); -} /* SkGeIocMib */ - - -/***************************************************************************** - * - * GetConfiguration - read configuration information - * - * Description: - * This function reads per-adapter configuration information from - * the options provided on the command line. - * - * Returns: - * none - */ -static void GetConfiguration( -SK_AC *pAC) /* pointer to the adapter context structure */ -{ -SK_I32 Port; /* preferred port */ -SK_BOOL AutoSet; -SK_BOOL DupSet; -int LinkSpeed = SK_LSPEED_AUTO; /* Link speed */ -int AutoNeg = 1; /* autoneg off (0) or on (1) */ -int DuplexCap = 0; /* 0=both,1=full,2=half */ -int FlowCtrl = SK_FLOW_MODE_SYM_OR_REM; /* FlowControl */ -int MSMode = SK_MS_MODE_AUTO; /* master/slave mode */ - -SK_BOOL IsConTypeDefined = SK_TRUE; -SK_BOOL IsLinkSpeedDefined = SK_TRUE; -SK_BOOL IsFlowCtrlDefined = SK_TRUE; -SK_BOOL IsRoleDefined = SK_TRUE; -SK_BOOL IsModeDefined = SK_TRUE; -/* - * The two parameters AutoNeg. and DuplexCap. map to one configuration - * parameter. The mapping is described by this table: - * DuplexCap -> | both | full | half | - * AutoNeg | | | | - * ----------------------------------------------------------------- - * Off | illegal | Full | Half | - * ----------------------------------------------------------------- - * On | AutoBoth | AutoFull | AutoHalf | - * ----------------------------------------------------------------- - * Sense | AutoSense | AutoSense | AutoSense | - */ -int Capabilities[3][3] = - { { -1, SK_LMODE_FULL , SK_LMODE_HALF }, - {SK_LMODE_AUTOBOTH , SK_LMODE_AUTOFULL , SK_LMODE_AUTOHALF }, - {SK_LMODE_AUTOSENSE, SK_LMODE_AUTOSENSE, SK_LMODE_AUTOSENSE} }; - -#define DC_BOTH 0 -#define DC_FULL 1 -#define DC_HALF 2 -#define AN_OFF 0 -#define AN_ON 1 -#define AN_SENS 2 -#define M_CurrPort pAC->GIni.GP[Port] - - - /* - ** Set the default values first for both ports! - */ - for (Port = 0; Port < SK_MAX_MACS; Port++) { - M_CurrPort.PLinkModeConf = Capabilities[AN_ON][DC_BOTH]; - M_CurrPort.PFlowCtrlMode = SK_FLOW_MODE_SYM_OR_REM; - M_CurrPort.PMSMode = SK_MS_MODE_AUTO; - M_CurrPort.PLinkSpeed = SK_LSPEED_AUTO; - } - - /* - ** Check merged parameter ConType. If it has not been used, - ** verify any other parameter (e.g. AutoNeg) and use default values. - ** - ** Stating both ConType and other lowlevel link parameters is also - ** possible. If this is the case, the passed ConType-parameter is - ** overwritten by the lowlevel link parameter. - ** - ** The following settings are used for a merged ConType-parameter: - ** - ** ConType DupCap AutoNeg FlowCtrl Role Speed - ** ------- ------ ------- -------- ---------- ----- - ** Auto Both On SymOrRem Auto Auto - ** 100FD Full Off None <ignored> 100 - ** 100HD Half Off None <ignored> 100 - ** 10FD Full Off None <ignored> 10 - ** 10HD Half Off None <ignored> 10 - ** - ** This ConType parameter is used for all ports of the adapter! - */ - if ( (ConType != NULL) && - (pAC->Index < SK_MAX_CARD_PARAM) && - (ConType[pAC->Index] != NULL) ) { - - /* Check chipset family */ - if ((!pAC->ChipsetType) && - (strcmp(ConType[pAC->Index],"Auto")!=0) && - (strcmp(ConType[pAC->Index],"")!=0)) { - /* Set the speed parameter back */ - printk("sk98lin: Illegal value \"%s\" " - "for ConType." - " Using Auto.\n", - ConType[pAC->Index]); - - sprintf(ConType[pAC->Index], "Auto"); - } - - if (strcmp(ConType[pAC->Index],"")==0) { - IsConTypeDefined = SK_FALSE; /* No ConType defined */ - } else if (strcmp(ConType[pAC->Index],"Auto")==0) { - for (Port = 0; Port < SK_MAX_MACS; Port++) { - M_CurrPort.PLinkModeConf = Capabilities[AN_ON][DC_BOTH]; - M_CurrPort.PFlowCtrlMode = SK_FLOW_MODE_SYM_OR_REM; - M_CurrPort.PMSMode = SK_MS_MODE_AUTO; - M_CurrPort.PLinkSpeed = SK_LSPEED_AUTO; - } - } else if (strcmp(ConType[pAC->Index],"100FD")==0) { - for (Port = 0; Port < SK_MAX_MACS; Port++) { - M_CurrPort.PLinkModeConf = Capabilities[AN_OFF][DC_FULL]; - M_CurrPort.PFlowCtrlMode = SK_FLOW_MODE_NONE; - M_CurrPort.PMSMode = SK_MS_MODE_AUTO; - M_CurrPort.PLinkSpeed = SK_LSPEED_100MBPS; - } - } else if (strcmp(ConType[pAC->Index],"100HD")==0) { - for (Port = 0; Port < SK_MAX_MACS; Port++) { - M_CurrPort.PLinkModeConf = Capabilities[AN_OFF][DC_HALF]; - M_CurrPort.PFlowCtrlMode = SK_FLOW_MODE_NONE; - M_CurrPort.PMSMode = SK_MS_MODE_AUTO; - M_CurrPort.PLinkSpeed = SK_LSPEED_100MBPS; - } - } else if (strcmp(ConType[pAC->Index],"10FD")==0) { - for (Port = 0; Port < SK_MAX_MACS; Port++) { - M_CurrPort.PLinkModeConf = Capabilities[AN_OFF][DC_FULL]; - M_CurrPort.PFlowCtrlMode = SK_FLOW_MODE_NONE; - M_CurrPort.PMSMode = SK_MS_MODE_AUTO; - M_CurrPort.PLinkSpeed = SK_LSPEED_10MBPS; - } - } else if (strcmp(ConType[pAC->Index],"10HD")==0) { - for (Port = 0; Port < SK_MAX_MACS; Port++) { - M_CurrPort.PLinkModeConf = Capabilities[AN_OFF][DC_HALF]; - M_CurrPort.PFlowCtrlMode = SK_FLOW_MODE_NONE; - M_CurrPort.PMSMode = SK_MS_MODE_AUTO; - M_CurrPort.PLinkSpeed = SK_LSPEED_10MBPS; - } - } else { - printk("sk98lin: Illegal value \"%s\" for ConType\n", - ConType[pAC->Index]); - IsConTypeDefined = SK_FALSE; /* Wrong ConType defined */ - } - } else { - IsConTypeDefined = SK_FALSE; /* No ConType defined */ - } - - /* - ** Parse any parameter settings for port A: - ** a) any LinkSpeed stated? - */ - if (Speed_A != NULL && pAC->Index<SK_MAX_CARD_PARAM && - Speed_A[pAC->Index] != NULL) { - if (strcmp(Speed_A[pAC->Index],"")==0) { - IsLinkSpeedDefined = SK_FALSE; - } else if (strcmp(Speed_A[pAC->Index],"Auto")==0) { - LinkSpeed = SK_LSPEED_AUTO; - } else if (strcmp(Speed_A[pAC->Index],"10")==0) { - LinkSpeed = SK_LSPEED_10MBPS; - } else if (strcmp(Speed_A[pAC->Index],"100")==0) { - LinkSpeed = SK_LSPEED_100MBPS; - } else if (strcmp(Speed_A[pAC->Index],"1000")==0) { - LinkSpeed = SK_LSPEED_1000MBPS; - } else { - printk("sk98lin: Illegal value \"%s\" for Speed_A\n", - Speed_A[pAC->Index]); - IsLinkSpeedDefined = SK_FALSE; - } - } else { - IsLinkSpeedDefined = SK_FALSE; - } - - /* - ** Check speed parameter: - ** Only copper type adapter and GE V2 cards - */ - if (((!pAC->ChipsetType) || (pAC->GIni.GICopperType != SK_TRUE)) && - ((LinkSpeed != SK_LSPEED_AUTO) && - (LinkSpeed != SK_LSPEED_1000MBPS))) { - printk("sk98lin: Illegal value for Speed_A. " - "Not a copper card or GE V2 card\n Using " - "speed 1000\n"); - LinkSpeed = SK_LSPEED_1000MBPS; - } - - /* - ** Decide whether to set new config value if somethig valid has - ** been received. - */ - if (IsLinkSpeedDefined) { - pAC->GIni.GP[0].PLinkSpeed = LinkSpeed; - } - - /* - ** b) Any Autonegotiation and DuplexCapabilities set? - ** Please note that both belong together... - */ - AutoNeg = AN_ON; /* tschilling: Default: Autonegotiation on! */ - AutoSet = SK_FALSE; - if (AutoNeg_A != NULL && pAC->Index<SK_MAX_CARD_PARAM && - AutoNeg_A[pAC->Index] != NULL) { - AutoSet = SK_TRUE; - if (strcmp(AutoNeg_A[pAC->Index],"")==0) { - AutoSet = SK_FALSE; - } else if (strcmp(AutoNeg_A[pAC->Index],"On")==0) { - AutoNeg = AN_ON; - } else if (strcmp(AutoNeg_A[pAC->Index],"Off")==0) { - AutoNeg = AN_OFF; - } else if (strcmp(AutoNeg_A[pAC->Index],"Sense")==0) { - AutoNeg = AN_SENS; - } else { - printk("sk98lin: Illegal value \"%s\" for AutoNeg_A\n", - AutoNeg_A[pAC->Index]); - } - } - - DuplexCap = DC_BOTH; - DupSet = SK_FALSE; - if (DupCap_A != NULL && pAC->Index<SK_MAX_CARD_PARAM && - DupCap_A[pAC->Index] != NULL) { - DupSet = SK_TRUE; - if (strcmp(DupCap_A[pAC->Index],"")==0) { - DupSet = SK_FALSE; - } else if (strcmp(DupCap_A[pAC->Index],"Both")==0) { - DuplexCap = DC_BOTH; - } else if (strcmp(DupCap_A[pAC->Index],"Full")==0) { - DuplexCap = DC_FULL; - } else if (strcmp(DupCap_A[pAC->Index],"Half")==0) { - DuplexCap = DC_HALF; - } else { - printk("sk98lin: Illegal value \"%s\" for DupCap_A\n", - DupCap_A[pAC->Index]); - } - } - - /* - ** Check for illegal combinations - */ - if ((LinkSpeed == SK_LSPEED_1000MBPS) && - ((DuplexCap == SK_LMODE_STAT_AUTOHALF) || - (DuplexCap == SK_LMODE_STAT_HALF)) && - (pAC->ChipsetType)) { - printk("sk98lin: Half Duplex not possible with Gigabit speed!\n" - " Using Full Duplex.\n"); - DuplexCap = DC_FULL; - } - - if ( AutoSet && AutoNeg==AN_SENS && DupSet) { - printk("sk98lin, Port A: DuplexCapabilities" - " ignored using Sense mode\n"); - } - - if (AutoSet && AutoNeg==AN_OFF && DupSet && DuplexCap==DC_BOTH){ - printk("sk98lin: Port A: Illegal combination" - " of values AutoNeg. and DuplexCap.\n Using " - "Full Duplex\n"); - DuplexCap = DC_FULL; - } - - if (AutoSet && AutoNeg==AN_OFF && !DupSet) { - DuplexCap = DC_FULL; - } - - if (!AutoSet && DupSet) { - printk("sk98lin: Port A: Duplex setting not" - " possible in\n default AutoNegotiation mode" - " (Sense).\n Using AutoNegotiation On\n"); - AutoNeg = AN_ON; - } - - /* - ** set the desired mode - */ - if (AutoSet || DupSet) { - pAC->GIni.GP[0].PLinkModeConf = Capabilities[AutoNeg][DuplexCap]; - } - - /* - ** c) Any Flowcontrol-parameter set? - */ - if (FlowCtrl_A != NULL && pAC->Index<SK_MAX_CARD_PARAM && - FlowCtrl_A[pAC->Index] != NULL) { - if (strcmp(FlowCtrl_A[pAC->Index],"") == 0) { - IsFlowCtrlDefined = SK_FALSE; - } else if (strcmp(FlowCtrl_A[pAC->Index],"SymOrRem") == 0) { - FlowCtrl = SK_FLOW_MODE_SYM_OR_REM; - } else if (strcmp(FlowCtrl_A[pAC->Index],"Sym")==0) { - FlowCtrl = SK_FLOW_MODE_SYMMETRIC; - } else if (strcmp(FlowCtrl_A[pAC->Index],"LocSend")==0) { - FlowCtrl = SK_FLOW_MODE_LOC_SEND; - } else if (strcmp(FlowCtrl_A[pAC->Index],"None")==0) { - FlowCtrl = SK_FLOW_MODE_NONE; - } else { - printk("sk98lin: Illegal value \"%s\" for FlowCtrl_A\n", - FlowCtrl_A[pAC->Index]); - IsFlowCtrlDefined = SK_FALSE; - } - } else { - IsFlowCtrlDefined = SK_FALSE; - } - - if (IsFlowCtrlDefined) { - if ((AutoNeg == AN_OFF) && (FlowCtrl != SK_FLOW_MODE_NONE)) { - printk("sk98lin: Port A: FlowControl" - " impossible without AutoNegotiation," - " disabled\n"); - FlowCtrl = SK_FLOW_MODE_NONE; - } - pAC->GIni.GP[0].PFlowCtrlMode = FlowCtrl; - } - - /* - ** d) What is with the RoleParameter? - */ - if (Role_A != NULL && pAC->Index<SK_MAX_CARD_PARAM && - Role_A[pAC->Index] != NULL) { - if (strcmp(Role_A[pAC->Index],"")==0) { - IsRoleDefined = SK_FALSE; - } else if (strcmp(Role_A[pAC->Index],"Auto")==0) { - MSMode = SK_MS_MODE_AUTO; - } else if (strcmp(Role_A[pAC->Index],"Master")==0) { - MSMode = SK_MS_MODE_MASTER; - } else if (strcmp(Role_A[pAC->Index],"Slave")==0) { - MSMode = SK_MS_MODE_SLAVE; - } else { - printk("sk98lin: Illegal value \"%s\" for Role_A\n", - Role_A[pAC->Index]); - IsRoleDefined = SK_FALSE; - } - } else { - IsRoleDefined = SK_FALSE; - } - - if (IsRoleDefined == SK_TRUE) { - pAC->GIni.GP[0].PMSMode = MSMode; - } - - - - /* - ** Parse any parameter settings for port B: - ** a) any LinkSpeed stated? - */ - IsConTypeDefined = SK_TRUE; - IsLinkSpeedDefined = SK_TRUE; - IsFlowCtrlDefined = SK_TRUE; - IsModeDefined = SK_TRUE; - - if (Speed_B != NULL && pAC->Index<SK_MAX_CARD_PARAM && - Speed_B[pAC->Index] != NULL) { - if (strcmp(Speed_B[pAC->Index],"")==0) { - IsLinkSpeedDefined = SK_FALSE; - } else if (strcmp(Speed_B[pAC->Index],"Auto")==0) { - LinkSpeed = SK_LSPEED_AUTO; - } else if (strcmp(Speed_B[pAC->Index],"10")==0) { - LinkSpeed = SK_LSPEED_10MBPS; - } else if (strcmp(Speed_B[pAC->Index],"100")==0) { - LinkSpeed = SK_LSPEED_100MBPS; - } else if (strcmp(Speed_B[pAC->Index],"1000")==0) { - LinkSpeed = SK_LSPEED_1000MBPS; - } else { - printk("sk98lin: Illegal value \"%s\" for Speed_B\n", - Speed_B[pAC->Index]); - IsLinkSpeedDefined = SK_FALSE; - } - } else { - IsLinkSpeedDefined = SK_FALSE; - } - - /* - ** Check speed parameter: - ** Only copper type adapter and GE V2 cards - */ - if (((!pAC->ChipsetType) || (pAC->GIni.GICopperType != SK_TRUE)) && - ((LinkSpeed != SK_LSPEED_AUTO) && - (LinkSpeed != SK_LSPEED_1000MBPS))) { - printk("sk98lin: Illegal value for Speed_B. " - "Not a copper card or GE V2 card\n Using " - "speed 1000\n"); - LinkSpeed = SK_LSPEED_1000MBPS; - } - - /* - ** Decide whether to set new config value if somethig valid has - ** been received. - */ - if (IsLinkSpeedDefined) { - pAC->GIni.GP[1].PLinkSpeed = LinkSpeed; - } - - /* - ** b) Any Autonegotiation and DuplexCapabilities set? - ** Please note that both belong together... - */ - AutoNeg = AN_SENS; /* default: do auto Sense */ - AutoSet = SK_FALSE; - if (AutoNeg_B != NULL && pAC->Index<SK_MAX_CARD_PARAM && - AutoNeg_B[pAC->Index] != NULL) { - AutoSet = SK_TRUE; - if (strcmp(AutoNeg_B[pAC->Index],"")==0) { - AutoSet = SK_FALSE; - } else if (strcmp(AutoNeg_B[pAC->Index],"On")==0) { - AutoNeg = AN_ON; - } else if (strcmp(AutoNeg_B[pAC->Index],"Off")==0) { - AutoNeg = AN_OFF; - } else if (strcmp(AutoNeg_B[pAC->Index],"Sense")==0) { - AutoNeg = AN_SENS; - } else { - printk("sk98lin: Illegal value \"%s\" for AutoNeg_B\n", - AutoNeg_B[pAC->Index]); - } - } - - DuplexCap = DC_BOTH; - DupSet = SK_FALSE; - if (DupCap_B != NULL && pAC->Index<SK_MAX_CARD_PARAM && - DupCap_B[pAC->Index] != NULL) { - DupSet = SK_TRUE; - if (strcmp(DupCap_B[pAC->Index],"")==0) { - DupSet = SK_FALSE; - } else if (strcmp(DupCap_B[pAC->Index],"Both")==0) { - DuplexCap = DC_BOTH; - } else if (strcmp(DupCap_B[pAC->Index],"Full")==0) { - DuplexCap = DC_FULL; - } else if (strcmp(DupCap_B[pAC->Index],"Half")==0) { - DuplexCap = DC_HALF; - } else { - printk("sk98lin: Illegal value \"%s\" for DupCap_B\n", - DupCap_B[pAC->Index]); - } - } - - - /* - ** Check for illegal combinations - */ - if ((LinkSpeed == SK_LSPEED_1000MBPS) && - ((DuplexCap == SK_LMODE_STAT_AUTOHALF) || - (DuplexCap == SK_LMODE_STAT_HALF)) && - (pAC->ChipsetType)) { - printk("sk98lin: Half Duplex not possible with Gigabit speed!\n" - " Using Full Duplex.\n"); - DuplexCap = DC_FULL; - } - - if (AutoSet && AutoNeg==AN_SENS && DupSet) { - printk("sk98lin, Port B: DuplexCapabilities" - " ignored using Sense mode\n"); - } - - if (AutoSet && AutoNeg==AN_OFF && DupSet && DuplexCap==DC_BOTH){ - printk("sk98lin: Port B: Illegal combination" - " of values AutoNeg. and DuplexCap.\n Using " - "Full Duplex\n"); - DuplexCap = DC_FULL; - } - - if (AutoSet && AutoNeg==AN_OFF && !DupSet) { - DuplexCap = DC_FULL; - } - - if (!AutoSet && DupSet) { - printk("sk98lin: Port B: Duplex setting not" - " possible in\n default AutoNegotiation mode" - " (Sense).\n Using AutoNegotiation On\n"); - AutoNeg = AN_ON; - } - - /* - ** set the desired mode - */ - if (AutoSet || DupSet) { - pAC->GIni.GP[1].PLinkModeConf = Capabilities[AutoNeg][DuplexCap]; - } - - /* - ** c) Any FlowCtrl parameter set? - */ - if (FlowCtrl_B != NULL && pAC->Index<SK_MAX_CARD_PARAM && - FlowCtrl_B[pAC->Index] != NULL) { - if (strcmp(FlowCtrl_B[pAC->Index],"") == 0) { - IsFlowCtrlDefined = SK_FALSE; - } else if (strcmp(FlowCtrl_B[pAC->Index],"SymOrRem") == 0) { - FlowCtrl = SK_FLOW_MODE_SYM_OR_REM; - } else if (strcmp(FlowCtrl_B[pAC->Index],"Sym")==0) { - FlowCtrl = SK_FLOW_MODE_SYMMETRIC; - } else if (strcmp(FlowCtrl_B[pAC->Index],"LocSend")==0) { - FlowCtrl = SK_FLOW_MODE_LOC_SEND; - } else if (strcmp(FlowCtrl_B[pAC->Index],"None")==0) { - FlowCtrl = SK_FLOW_MODE_NONE; - } else { - printk("sk98lin: Illegal value \"%s\" for FlowCtrl_B\n", - FlowCtrl_B[pAC->Index]); - IsFlowCtrlDefined = SK_FALSE; - } - } else { - IsFlowCtrlDefined = SK_FALSE; - } - - if (IsFlowCtrlDefined) { - if ((AutoNeg == AN_OFF) && (FlowCtrl != SK_FLOW_MODE_NONE)) { - printk("sk98lin: Port B: FlowControl" - " impossible without AutoNegotiation," - " disabled\n"); - FlowCtrl = SK_FLOW_MODE_NONE; - } - pAC->GIni.GP[1].PFlowCtrlMode = FlowCtrl; - } - - /* - ** d) What is the RoleParameter? - */ - if (Role_B != NULL && pAC->Index<SK_MAX_CARD_PARAM && - Role_B[pAC->Index] != NULL) { - if (strcmp(Role_B[pAC->Index],"")==0) { - IsRoleDefined = SK_FALSE; - } else if (strcmp(Role_B[pAC->Index],"Auto")==0) { - MSMode = SK_MS_MODE_AUTO; - } else if (strcmp(Role_B[pAC->Index],"Master")==0) { - MSMode = SK_MS_MODE_MASTER; - } else if (strcmp(Role_B[pAC->Index],"Slave")==0) { - MSMode = SK_MS_MODE_SLAVE; - } else { - printk("sk98lin: Illegal value \"%s\" for Role_B\n", - Role_B[pAC->Index]); - IsRoleDefined = SK_FALSE; - } - } else { - IsRoleDefined = SK_FALSE; - } - - if (IsRoleDefined) { - pAC->GIni.GP[1].PMSMode = MSMode; - } - - /* - ** Evaluate settings for both ports - */ - pAC->ActivePort = 0; - if (PrefPort != NULL && pAC->Index<SK_MAX_CARD_PARAM && - PrefPort[pAC->Index] != NULL) { - if (strcmp(PrefPort[pAC->Index],"") == 0) { /* Auto */ - pAC->ActivePort = 0; - pAC->Rlmt.Net[0].Preference = -1; /* auto */ - pAC->Rlmt.Net[0].PrefPort = 0; - } else if (strcmp(PrefPort[pAC->Index],"A") == 0) { - /* - ** do not set ActivePort here, thus a port - ** switch is issued after net up. - */ - Port = 0; - pAC->Rlmt.Net[0].Preference = Port; - pAC->Rlmt.Net[0].PrefPort = Port; - } else if (strcmp(PrefPort[pAC->Index],"B") == 0) { - /* - ** do not set ActivePort here, thus a port - ** switch is issued after net up. - */ - if (pAC->GIni.GIMacsFound == 1) { - printk("sk98lin: Illegal value \"B\" for PrefPort.\n" - " Port B not available on single port adapters.\n"); - - pAC->ActivePort = 0; - pAC->Rlmt.Net[0].Preference = -1; /* auto */ - pAC->Rlmt.Net[0].PrefPort = 0; - } else { - Port = 1; - pAC->Rlmt.Net[0].Preference = Port; - pAC->Rlmt.Net[0].PrefPort = Port; - } - } else { - printk("sk98lin: Illegal value \"%s\" for PrefPort\n", - PrefPort[pAC->Index]); - } - } - - pAC->RlmtNets = 1; - - if (RlmtMode != NULL && pAC->Index<SK_MAX_CARD_PARAM && - RlmtMode[pAC->Index] != NULL) { - if (strcmp(RlmtMode[pAC->Index], "") == 0) { - pAC->RlmtMode = 0; - } else if (strcmp(RlmtMode[pAC->Index], "CheckLinkState") == 0) { - pAC->RlmtMode = SK_RLMT_CHECK_LINK; - } else if (strcmp(RlmtMode[pAC->Index], "CheckLocalPort") == 0) { - pAC->RlmtMode = SK_RLMT_CHECK_LINK | - SK_RLMT_CHECK_LOC_LINK; - } else if (strcmp(RlmtMode[pAC->Index], "CheckSeg") == 0) { - pAC->RlmtMode = SK_RLMT_CHECK_LINK | - SK_RLMT_CHECK_LOC_LINK | - SK_RLMT_CHECK_SEG; - } else if ((strcmp(RlmtMode[pAC->Index], "DualNet") == 0) && - (pAC->GIni.GIMacsFound == 2)) { - pAC->RlmtMode = SK_RLMT_CHECK_LINK; - pAC->RlmtNets = 2; - } else { - printk("sk98lin: Illegal value \"%s\" for" - " RlmtMode, using default\n", - RlmtMode[pAC->Index]); - pAC->RlmtMode = 0; - } - } else { - pAC->RlmtMode = 0; - } - - /* - ** Check the interrupt moderation parameters - */ - if (Moderation[pAC->Index] != NULL) { - if (strcmp(Moderation[pAC->Index], "") == 0) { - pAC->DynIrqModInfo.IntModTypeSelect = C_INT_MOD_NONE; - } else if (strcmp(Moderation[pAC->Index], "Static") == 0) { - pAC->DynIrqModInfo.IntModTypeSelect = C_INT_MOD_STATIC; - } else if (strcmp(Moderation[pAC->Index], "Dynamic") == 0) { - pAC->DynIrqModInfo.IntModTypeSelect = C_INT_MOD_DYNAMIC; - } else if (strcmp(Moderation[pAC->Index], "None") == 0) { - pAC->DynIrqModInfo.IntModTypeSelect = C_INT_MOD_NONE; - } else { - printk("sk98lin: Illegal value \"%s\" for Moderation.\n" - " Disable interrupt moderation.\n", - Moderation[pAC->Index]); - pAC->DynIrqModInfo.IntModTypeSelect = C_INT_MOD_NONE; - } - } else { - pAC->DynIrqModInfo.IntModTypeSelect = C_INT_MOD_NONE; - } - - if (Stats[pAC->Index] != NULL) { - if (strcmp(Stats[pAC->Index], "Yes") == 0) { - pAC->DynIrqModInfo.DisplayStats = SK_TRUE; - } else { - pAC->DynIrqModInfo.DisplayStats = SK_FALSE; - } - } else { - pAC->DynIrqModInfo.DisplayStats = SK_FALSE; - } - - if (ModerationMask[pAC->Index] != NULL) { - if (strcmp(ModerationMask[pAC->Index], "Rx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_RX_ONLY; - } else if (strcmp(ModerationMask[pAC->Index], "Tx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_TX_ONLY; - } else if (strcmp(ModerationMask[pAC->Index], "Sp") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_SP_ONLY; - } else if (strcmp(ModerationMask[pAC->Index], "RxSp") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_SP_RX; - } else if (strcmp(ModerationMask[pAC->Index], "SpRx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_SP_RX; - } else if (strcmp(ModerationMask[pAC->Index], "RxTx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_TX_RX; - } else if (strcmp(ModerationMask[pAC->Index], "TxRx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_TX_RX; - } else if (strcmp(ModerationMask[pAC->Index], "TxSp") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_SP_TX; - } else if (strcmp(ModerationMask[pAC->Index], "SpTx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_SP_TX; - } else if (strcmp(ModerationMask[pAC->Index], "RxTxSp") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_RX_TX_SP; - } else if (strcmp(ModerationMask[pAC->Index], "RxSpTx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_RX_TX_SP; - } else if (strcmp(ModerationMask[pAC->Index], "TxRxSp") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_RX_TX_SP; - } else if (strcmp(ModerationMask[pAC->Index], "TxSpRx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_RX_TX_SP; - } else if (strcmp(ModerationMask[pAC->Index], "SpTxRx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_RX_TX_SP; - } else if (strcmp(ModerationMask[pAC->Index], "SpRxTx") == 0) { - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_RX_TX_SP; - } else { /* some rubbish */ - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_RX_ONLY; - } - } else { /* operator has stated nothing */ - pAC->DynIrqModInfo.MaskIrqModeration = IRQ_MASK_TX_RX; - } - - if (AutoSizing[pAC->Index] != NULL) { - if (strcmp(AutoSizing[pAC->Index], "On") == 0) { - pAC->DynIrqModInfo.AutoSizing = SK_FALSE; - } else { - pAC->DynIrqModInfo.AutoSizing = SK_FALSE; - } - } else { /* operator has stated nothing */ - pAC->DynIrqModInfo.AutoSizing = SK_FALSE; - } - - if (IntsPerSec[pAC->Index] != 0) { - if ((IntsPerSec[pAC->Index]< C_INT_MOD_IPS_LOWER_RANGE) || - (IntsPerSec[pAC->Index] > C_INT_MOD_IPS_UPPER_RANGE)) { - printk("sk98lin: Illegal value \"%d\" for IntsPerSec. (Range: %d - %d)\n" - " Using default value of %i.\n", - IntsPerSec[pAC->Index], - C_INT_MOD_IPS_LOWER_RANGE, - C_INT_MOD_IPS_UPPER_RANGE, - C_INTS_PER_SEC_DEFAULT); - pAC->DynIrqModInfo.MaxModIntsPerSec = C_INTS_PER_SEC_DEFAULT; - } else { - pAC->DynIrqModInfo.MaxModIntsPerSec = IntsPerSec[pAC->Index]; - } - } else { - pAC->DynIrqModInfo.MaxModIntsPerSec = C_INTS_PER_SEC_DEFAULT; - } - - /* - ** Evaluate upper and lower moderation threshold - */ - pAC->DynIrqModInfo.MaxModIntsPerSecUpperLimit = - pAC->DynIrqModInfo.MaxModIntsPerSec + - (pAC->DynIrqModInfo.MaxModIntsPerSec / 2); - - pAC->DynIrqModInfo.MaxModIntsPerSecLowerLimit = - pAC->DynIrqModInfo.MaxModIntsPerSec - - (pAC->DynIrqModInfo.MaxModIntsPerSec / 2); - - pAC->DynIrqModInfo.PrevTimeVal = jiffies; /* initial value */ - - -} /* GetConfiguration */ - - -/***************************************************************************** - * - * ProductStr - return a adapter identification string from vpd - * - * Description: - * This function reads the product name string from the vpd area - * and puts it the field pAC->DeviceString. - * - * Returns: N/A - */ -static inline int ProductStr( - SK_AC *pAC, /* pointer to adapter context */ - char *DeviceStr, /* result string */ - int StrLen /* length of the string */ -) -{ -char Keyword[] = VPD_NAME; /* vpd productname identifier */ -int ReturnCode; /* return code from vpd_read */ -unsigned long Flags; - - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - ReturnCode = VpdRead(pAC, pAC->IoBase, Keyword, DeviceStr, &StrLen); - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - - return ReturnCode; -} /* ProductStr */ - -/***************************************************************************** - * - * StartDrvCleanupTimer - Start timer to check for descriptors which - * might be placed in descriptor ring, but - * havent been handled up to now - * - * Description: - * This function requests a HW-timer fo the Yukon card. The actions to - * perform when this timer expires, are located in the SkDrvEvent(). - * - * Returns: N/A - */ -static void -StartDrvCleanupTimer(SK_AC *pAC) { - SK_EVPARA EventParam; /* Event struct for timer event */ - - SK_MEMSET((char *) &EventParam, 0, sizeof(EventParam)); - EventParam.Para32[0] = SK_DRV_RX_CLEANUP_TIMER; - SkTimerStart(pAC, pAC->IoBase, &pAC->DrvCleanupTimer, - SK_DRV_RX_CLEANUP_TIMER_LENGTH, - SKGE_DRV, SK_DRV_TIMER, EventParam); -} - -/***************************************************************************** - * - * StopDrvCleanupTimer - Stop timer to check for descriptors - * - * Description: - * This function requests a HW-timer fo the Yukon card. The actions to - * perform when this timer expires, are located in the SkDrvEvent(). - * - * Returns: N/A - */ -static void -StopDrvCleanupTimer(SK_AC *pAC) { - SkTimerStop(pAC, pAC->IoBase, &pAC->DrvCleanupTimer); - SK_MEMSET((char *) &pAC->DrvCleanupTimer, 0, sizeof(SK_TIMER)); -} - -/****************************************************************************/ -/* functions for common modules *********************************************/ -/****************************************************************************/ - - -/***************************************************************************** - * - * SkDrvAllocRlmtMbuf - allocate an RLMT mbuf - * - * Description: - * This routine returns an RLMT mbuf or NULL. The RLMT Mbuf structure - * is embedded into a socket buff data area. - * - * Context: - * runtime - * - * Returns: - * NULL or pointer to Mbuf. - */ -SK_MBUF *SkDrvAllocRlmtMbuf( -SK_AC *pAC, /* pointer to adapter context */ -SK_IOC IoC, /* the IO-context */ -unsigned BufferSize) /* size of the requested buffer */ -{ -SK_MBUF *pRlmtMbuf; /* pointer to a new rlmt-mbuf structure */ -struct sk_buff *pMsgBlock; /* pointer to a new message block */ - - pMsgBlock = alloc_skb(BufferSize + sizeof(SK_MBUF), GFP_ATOMIC); - if (pMsgBlock == NULL) { - return (NULL); - } - pRlmtMbuf = (SK_MBUF*) pMsgBlock->data; - skb_reserve(pMsgBlock, sizeof(SK_MBUF)); - pRlmtMbuf->pNext = NULL; - pRlmtMbuf->pOs = pMsgBlock; - pRlmtMbuf->pData = pMsgBlock->data; /* Data buffer. */ - pRlmtMbuf->Size = BufferSize; /* Data buffer size. */ - pRlmtMbuf->Length = 0; /* Length of packet (<= Size). */ - return (pRlmtMbuf); - -} /* SkDrvAllocRlmtMbuf */ - - -/***************************************************************************** - * - * SkDrvFreeRlmtMbuf - free an RLMT mbuf - * - * Description: - * This routine frees one or more RLMT mbuf(s). - * - * Context: - * runtime - * - * Returns: - * Nothing - */ -void SkDrvFreeRlmtMbuf( -SK_AC *pAC, /* pointer to adapter context */ -SK_IOC IoC, /* the IO-context */ -SK_MBUF *pMbuf) /* size of the requested buffer */ -{ -SK_MBUF *pFreeMbuf; -SK_MBUF *pNextMbuf; - - pFreeMbuf = pMbuf; - do { - pNextMbuf = pFreeMbuf->pNext; - DEV_KFREE_SKB_ANY(pFreeMbuf->pOs); - pFreeMbuf = pNextMbuf; - } while ( pFreeMbuf != NULL ); -} /* SkDrvFreeRlmtMbuf */ - - -/***************************************************************************** - * - * SkOsGetTime - provide a time value - * - * Description: - * This routine provides a time value. The unit is 1/HZ (defined by Linux). - * It is not used for absolute time, but only for time differences. - * - * - * Returns: - * Time value - */ -SK_U64 SkOsGetTime(SK_AC *pAC) -{ - SK_U64 PrivateJiffies; - SkOsGetTimeCurrent(pAC, &PrivateJiffies); - return PrivateJiffies; -} /* SkOsGetTime */ - - -/***************************************************************************** - * - * SkPciReadCfgDWord - read a 32 bit value from pci config space - * - * Description: - * This routine reads a 32 bit value from the pci configuration - * space. - * - * Returns: - * 0 - indicate everything worked ok. - * != 0 - error indication - */ -int SkPciReadCfgDWord( -SK_AC *pAC, /* Adapter Control structure pointer */ -int PciAddr, /* PCI register address */ -SK_U32 *pVal) /* pointer to store the read value */ -{ - pci_read_config_dword(pAC->PciDev, PciAddr, pVal); - return(0); -} /* SkPciReadCfgDWord */ - - -/***************************************************************************** - * - * SkPciReadCfgWord - read a 16 bit value from pci config space - * - * Description: - * This routine reads a 16 bit value from the pci configuration - * space. - * - * Returns: - * 0 - indicate everything worked ok. - * != 0 - error indication - */ -int SkPciReadCfgWord( -SK_AC *pAC, /* Adapter Control structure pointer */ -int PciAddr, /* PCI register address */ -SK_U16 *pVal) /* pointer to store the read value */ -{ - pci_read_config_word(pAC->PciDev, PciAddr, pVal); - return(0); -} /* SkPciReadCfgWord */ - - -/***************************************************************************** - * - * SkPciReadCfgByte - read a 8 bit value from pci config space - * - * Description: - * This routine reads a 8 bit value from the pci configuration - * space. - * - * Returns: - * 0 - indicate everything worked ok. - * != 0 - error indication - */ -int SkPciReadCfgByte( -SK_AC *pAC, /* Adapter Control structure pointer */ -int PciAddr, /* PCI register address */ -SK_U8 *pVal) /* pointer to store the read value */ -{ - pci_read_config_byte(pAC->PciDev, PciAddr, pVal); - return(0); -} /* SkPciReadCfgByte */ - - -/***************************************************************************** - * - * SkPciWriteCfgWord - write a 16 bit value to pci config space - * - * Description: - * This routine writes a 16 bit value to the pci configuration - * space. The flag PciConfigUp indicates whether the config space - * is accesible or must be set up first. - * - * Returns: - * 0 - indicate everything worked ok. - * != 0 - error indication - */ -int SkPciWriteCfgWord( -SK_AC *pAC, /* Adapter Control structure pointer */ -int PciAddr, /* PCI register address */ -SK_U16 Val) /* pointer to store the read value */ -{ - pci_write_config_word(pAC->PciDev, PciAddr, Val); - return(0); -} /* SkPciWriteCfgWord */ - - -/***************************************************************************** - * - * SkPciWriteCfgWord - write a 8 bit value to pci config space - * - * Description: - * This routine writes a 8 bit value to the pci configuration - * space. The flag PciConfigUp indicates whether the config space - * is accesible or must be set up first. - * - * Returns: - * 0 - indicate everything worked ok. - * != 0 - error indication - */ -int SkPciWriteCfgByte( -SK_AC *pAC, /* Adapter Control structure pointer */ -int PciAddr, /* PCI register address */ -SK_U8 Val) /* pointer to store the read value */ -{ - pci_write_config_byte(pAC->PciDev, PciAddr, Val); - return(0); -} /* SkPciWriteCfgByte */ - - -/***************************************************************************** - * - * SkDrvEvent - handle driver events - * - * Description: - * This function handles events from all modules directed to the driver - * - * Context: - * Is called under protection of slow path lock. - * - * Returns: - * 0 if everything ok - * < 0 on error - * - */ -int SkDrvEvent( -SK_AC *pAC, /* pointer to adapter context */ -SK_IOC IoC, /* io-context */ -SK_U32 Event, /* event-id */ -SK_EVPARA Param) /* event-parameter */ -{ -SK_MBUF *pRlmtMbuf; /* pointer to a rlmt-mbuf structure */ -struct sk_buff *pMsg; /* pointer to a message block */ -int FromPort; /* the port from which we switch away */ -int ToPort; /* the port we switch to */ -SK_EVPARA NewPara; /* parameter for further events */ -int Stat; -unsigned long Flags; -SK_BOOL DualNet; - - switch (Event) { - case SK_DRV_ADAP_FAIL: - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("ADAPTER FAIL EVENT\n")); - printk("%s: Adapter failed.\n", pAC->dev[0]->name); - /* disable interrupts */ - SK_OUT32(pAC->IoBase, B0_IMSK, 0); - /* cgoos */ - break; - case SK_DRV_PORT_FAIL: - FromPort = Param.Para32[0]; - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("PORT FAIL EVENT, Port: %d\n", FromPort)); - if (FromPort == 0) { - printk("%s: Port A failed.\n", pAC->dev[0]->name); - } else { - printk("%s: Port B failed.\n", pAC->dev[1]->name); - } - /* cgoos */ - break; - case SK_DRV_PORT_RESET: /* SK_U32 PortIdx */ - /* action list 4 */ - FromPort = Param.Para32[0]; - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("PORT RESET EVENT, Port: %d ", FromPort)); - NewPara.Para64 = FromPort; - SkPnmiEvent(pAC, IoC, SK_PNMI_EVT_XMAC_RESET, NewPara); - spin_lock_irqsave( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - - SkGeStopPort(pAC, IoC, FromPort, SK_STOP_ALL, SK_HARD_RST); - netif_carrier_off(pAC->dev[Param.Para32[0]]); - spin_unlock_irqrestore( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - - /* clear rx ring from received frames */ - ReceiveIrq(pAC, &pAC->RxPort[FromPort], SK_FALSE); - - ClearTxRing(pAC, &pAC->TxPort[FromPort][TX_PRIO_LOW]); - spin_lock_irqsave( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - - /* tschilling: Handling of return value inserted. */ - if (SkGeInitPort(pAC, IoC, FromPort)) { - if (FromPort == 0) { - printk("%s: SkGeInitPort A failed.\n", pAC->dev[0]->name); - } else { - printk("%s: SkGeInitPort B failed.\n", pAC->dev[1]->name); - } - } - SkAddrMcUpdate(pAC,IoC, FromPort); - PortReInitBmu(pAC, FromPort); - SkGePollTxD(pAC, IoC, FromPort, SK_TRUE); - ClearAndStartRx(pAC, FromPort); - spin_unlock_irqrestore( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - break; - case SK_DRV_NET_UP: /* SK_U32 PortIdx */ - { struct net_device *dev = pAC->dev[Param.Para32[0]]; - /* action list 5 */ - FromPort = Param.Para32[0]; - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("NET UP EVENT, Port: %d ", Param.Para32[0])); - /* Mac update */ - SkAddrMcUpdate(pAC,IoC, FromPort); - - if (DoPrintInterfaceChange) { - printk("%s: network connection up using" - " port %c\n", pAC->dev[Param.Para32[0]]->name, 'A'+Param.Para32[0]); - - /* tschilling: Values changed according to LinkSpeedUsed. */ - Stat = pAC->GIni.GP[FromPort].PLinkSpeedUsed; - if (Stat == SK_LSPEED_STAT_10MBPS) { - printk(" speed: 10\n"); - } else if (Stat == SK_LSPEED_STAT_100MBPS) { - printk(" speed: 100\n"); - } else if (Stat == SK_LSPEED_STAT_1000MBPS) { - printk(" speed: 1000\n"); - } else { - printk(" speed: unknown\n"); - } - - - Stat = pAC->GIni.GP[FromPort].PLinkModeStatus; - if (Stat == SK_LMODE_STAT_AUTOHALF || - Stat == SK_LMODE_STAT_AUTOFULL) { - printk(" autonegotiation: yes\n"); - } - else { - printk(" autonegotiation: no\n"); - } - if (Stat == SK_LMODE_STAT_AUTOHALF || - Stat == SK_LMODE_STAT_HALF) { - printk(" duplex mode: half\n"); - } - else { - printk(" duplex mode: full\n"); - } - Stat = pAC->GIni.GP[FromPort].PFlowCtrlStatus; - if (Stat == SK_FLOW_STAT_REM_SEND ) { - printk(" flowctrl: remote send\n"); - } - else if (Stat == SK_FLOW_STAT_LOC_SEND ){ - printk(" flowctrl: local send\n"); - } - else if (Stat == SK_FLOW_STAT_SYMMETRIC ){ - printk(" flowctrl: symmetric\n"); - } - else { - printk(" flowctrl: none\n"); - } - - /* tschilling: Check against CopperType now. */ - if ((pAC->GIni.GICopperType == SK_TRUE) && - (pAC->GIni.GP[FromPort].PLinkSpeedUsed == - SK_LSPEED_STAT_1000MBPS)) { - Stat = pAC->GIni.GP[FromPort].PMSStatus; - if (Stat == SK_MS_STAT_MASTER ) { - printk(" role: master\n"); - } - else if (Stat == SK_MS_STAT_SLAVE ) { - printk(" role: slave\n"); - } - else { - printk(" role: ???\n"); - } - } - - /* - Display dim (dynamic interrupt moderation) - informations - */ - if (pAC->DynIrqModInfo.IntModTypeSelect == C_INT_MOD_STATIC) - printk(" irq moderation: static (%d ints/sec)\n", - pAC->DynIrqModInfo.MaxModIntsPerSec); - else if (pAC->DynIrqModInfo.IntModTypeSelect == C_INT_MOD_DYNAMIC) - printk(" irq moderation: dynamic (%d ints/sec)\n", - pAC->DynIrqModInfo.MaxModIntsPerSec); - else - printk(" irq moderation: disabled\n"); - - - printk(" scatter-gather: %s\n", - (dev->features & NETIF_F_SG) ? "enabled" : "disabled"); - printk(" tx-checksum: %s\n", - (dev->features & NETIF_F_IP_CSUM) ? "enabled" : "disabled"); - printk(" rx-checksum: %s\n", - pAC->RxPort[Param.Para32[0]].RxCsum ? "enabled" : "disabled"); - - } else { - DoPrintInterfaceChange = SK_TRUE; - } - - if ((Param.Para32[0] != pAC->ActivePort) && - (pAC->RlmtNets == 1)) { - NewPara.Para32[0] = pAC->ActivePort; - NewPara.Para32[1] = Param.Para32[0]; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_SWITCH_INTERN, - NewPara); - } - - /* Inform the world that link protocol is up. */ - netif_carrier_on(dev); - break; - } - case SK_DRV_NET_DOWN: /* SK_U32 Reason */ - /* action list 7 */ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("NET DOWN EVENT ")); - if (DoPrintInterfaceChange) { - printk("%s: network connection down\n", - pAC->dev[Param.Para32[1]]->name); - } else { - DoPrintInterfaceChange = SK_TRUE; - } - netif_carrier_off(pAC->dev[Param.Para32[1]]); - break; - case SK_DRV_SWITCH_HARD: /* SK_U32 FromPortIdx SK_U32 ToPortIdx */ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("PORT SWITCH HARD ")); - case SK_DRV_SWITCH_SOFT: /* SK_U32 FromPortIdx SK_U32 ToPortIdx */ - /* action list 6 */ - printk("%s: switching to port %c\n", pAC->dev[0]->name, - 'A'+Param.Para32[1]); - case SK_DRV_SWITCH_INTERN: /* SK_U32 FromPortIdx SK_U32 ToPortIdx */ - FromPort = Param.Para32[0]; - ToPort = Param.Para32[1]; - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("PORT SWITCH EVENT, From: %d To: %d (Pref %d) ", - FromPort, ToPort, pAC->Rlmt.Net[0].PrefPort)); - NewPara.Para64 = FromPort; - SkPnmiEvent(pAC, IoC, SK_PNMI_EVT_XMAC_RESET, NewPara); - NewPara.Para64 = ToPort; - SkPnmiEvent(pAC, IoC, SK_PNMI_EVT_XMAC_RESET, NewPara); - spin_lock_irqsave( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - spin_lock(&pAC->TxPort[ToPort][TX_PRIO_LOW].TxDesRingLock); - SkGeStopPort(pAC, IoC, FromPort, SK_STOP_ALL, SK_SOFT_RST); - SkGeStopPort(pAC, IoC, ToPort, SK_STOP_ALL, SK_SOFT_RST); - spin_unlock(&pAC->TxPort[ToPort][TX_PRIO_LOW].TxDesRingLock); - spin_unlock_irqrestore( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - - ReceiveIrq(pAC, &pAC->RxPort[FromPort], SK_FALSE); /* clears rx ring */ - ReceiveIrq(pAC, &pAC->RxPort[ToPort], SK_FALSE); /* clears rx ring */ - - ClearTxRing(pAC, &pAC->TxPort[FromPort][TX_PRIO_LOW]); - ClearTxRing(pAC, &pAC->TxPort[ToPort][TX_PRIO_LOW]); - spin_lock_irqsave( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - spin_lock(&pAC->TxPort[ToPort][TX_PRIO_LOW].TxDesRingLock); - pAC->ActivePort = ToPort; -#if 0 - SetQueueSizes(pAC); -#else - /* tschilling: New common function with minimum size check. */ - DualNet = SK_FALSE; - if (pAC->RlmtNets == 2) { - DualNet = SK_TRUE; - } - - if (SkGeInitAssignRamToQueues( - pAC, - pAC->ActivePort, - DualNet)) { - spin_unlock(&pAC->TxPort[ToPort][TX_PRIO_LOW].TxDesRingLock); - spin_unlock_irqrestore( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - printk("SkGeInitAssignRamToQueues failed.\n"); - break; - } -#endif - /* tschilling: Handling of return values inserted. */ - if (SkGeInitPort(pAC, IoC, FromPort) || - SkGeInitPort(pAC, IoC, ToPort)) { - printk("%s: SkGeInitPort failed.\n", pAC->dev[0]->name); - } - if (Event == SK_DRV_SWITCH_SOFT) { - SkMacRxTxEnable(pAC, IoC, FromPort); - } - SkMacRxTxEnable(pAC, IoC, ToPort); - SkAddrSwap(pAC, IoC, FromPort, ToPort); - SkAddrMcUpdate(pAC, IoC, FromPort); - SkAddrMcUpdate(pAC, IoC, ToPort); - PortReInitBmu(pAC, FromPort); - PortReInitBmu(pAC, ToPort); - SkGePollTxD(pAC, IoC, FromPort, SK_TRUE); - SkGePollTxD(pAC, IoC, ToPort, SK_TRUE); - ClearAndStartRx(pAC, FromPort); - ClearAndStartRx(pAC, ToPort); - spin_unlock(&pAC->TxPort[ToPort][TX_PRIO_LOW].TxDesRingLock); - spin_unlock_irqrestore( - &pAC->TxPort[FromPort][TX_PRIO_LOW].TxDesRingLock, - Flags); - break; - case SK_DRV_RLMT_SEND: /* SK_MBUF *pMb */ - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("RLS ")); - pRlmtMbuf = (SK_MBUF*) Param.pParaPtr; - pMsg = (struct sk_buff*) pRlmtMbuf->pOs; - skb_put(pMsg, pRlmtMbuf->Length); - if (XmitFrame(pAC, &pAC->TxPort[pRlmtMbuf->PortIdx][TX_PRIO_LOW], - pMsg) < 0) - - DEV_KFREE_SKB_ANY(pMsg); - break; - case SK_DRV_TIMER: - if (Param.Para32[0] == SK_DRV_MODERATION_TIMER) { - /* - ** expiration of the moderation timer implies that - ** dynamic moderation is to be applied - */ - SkDimStartModerationTimer(pAC); - SkDimModerate(pAC); - if (pAC->DynIrqModInfo.DisplayStats) { - SkDimDisplayModerationSettings(pAC); - } - } else if (Param.Para32[0] == SK_DRV_RX_CLEANUP_TIMER) { - /* - ** check if we need to check for descriptors which - ** haven't been handled the last millisecs - */ - StartDrvCleanupTimer(pAC); - if (pAC->GIni.GIMacsFound == 2) { - ReceiveIrq(pAC, &pAC->RxPort[1], SK_FALSE); - } - ReceiveIrq(pAC, &pAC->RxPort[0], SK_FALSE); - } else { - printk("Expiration of unknown timer\n"); - } - break; - default: - break; - } - SK_DBG_MSG(NULL, SK_DBGMOD_DRV, SK_DBGCAT_DRV_EVENT, - ("END EVENT ")); - - return (0); -} /* SkDrvEvent */ - - -/***************************************************************************** - * - * SkErrorLog - log errors - * - * Description: - * This function logs errors to the system buffer and to the console - * - * Returns: - * 0 if everything ok - * < 0 on error - * - */ -void SkErrorLog( -SK_AC *pAC, -int ErrClass, -int ErrNum, -char *pErrorMsg) -{ -char ClassStr[80]; - - switch (ErrClass) { - case SK_ERRCL_OTHER: - strcpy(ClassStr, "Other error"); - break; - case SK_ERRCL_CONFIG: - strcpy(ClassStr, "Configuration error"); - break; - case SK_ERRCL_INIT: - strcpy(ClassStr, "Initialization error"); - break; - case SK_ERRCL_NORES: - strcpy(ClassStr, "Out of resources error"); - break; - case SK_ERRCL_SW: - strcpy(ClassStr, "internal Software error"); - break; - case SK_ERRCL_HW: - strcpy(ClassStr, "Hardware failure"); - break; - case SK_ERRCL_COMM: - strcpy(ClassStr, "Communication error"); - break; - } - printk(KERN_INFO "%s: -- ERROR --\n Class: %s\n" - " Nr: 0x%x\n Msg: %s\n", pAC->dev[0]->name, - ClassStr, ErrNum, pErrorMsg); - -} /* SkErrorLog */ - -#ifdef SK_DIAG_SUPPORT - -/***************************************************************************** - * - * SkDrvEnterDiagMode - handles DIAG attach request - * - * Description: - * Notify the kernel to NOT access the card any longer due to DIAG - * Deinitialize the Card - * - * Returns: - * int - */ -int SkDrvEnterDiagMode( -SK_AC *pAc) /* pointer to adapter context */ -{ - DEV_NET *pNet = netdev_priv(pAc->dev[0]); - SK_AC *pAC = pNet->pAC; - - SK_MEMCPY(&(pAc->PnmiBackup), &(pAc->PnmiStruct), - sizeof(SK_PNMI_STRUCT_DATA)); - - pAC->DiagModeActive = DIAG_ACTIVE; - if (pAC->BoardLevel > SK_INIT_DATA) { - if (netif_running(pAC->dev[0])) { - pAC->WasIfUp[0] = SK_TRUE; - pAC->DiagFlowCtrl = SK_TRUE; /* for SkGeClose */ - DoPrintInterfaceChange = SK_FALSE; - SkDrvDeInitAdapter(pAC, 0); /* performs SkGeClose */ - } else { - pAC->WasIfUp[0] = SK_FALSE; - } - if (pNet != netdev_priv(pAC->dev[1])) { - pNet = netdev_priv(pAC->dev[1]); - if (netif_running(pAC->dev[1])) { - pAC->WasIfUp[1] = SK_TRUE; - pAC->DiagFlowCtrl = SK_TRUE; /* for SkGeClose */ - DoPrintInterfaceChange = SK_FALSE; - SkDrvDeInitAdapter(pAC, 1); /* do SkGeClose */ - } else { - pAC->WasIfUp[1] = SK_FALSE; - } - } - pAC->BoardLevel = SK_INIT_DATA; - } - return(0); -} - -/***************************************************************************** - * - * SkDrvLeaveDiagMode - handles DIAG detach request - * - * Description: - * Notify the kernel to may access the card again after use by DIAG - * Initialize the Card - * - * Returns: - * int - */ -int SkDrvLeaveDiagMode( -SK_AC *pAc) /* pointer to adapter control context */ -{ - SK_MEMCPY(&(pAc->PnmiStruct), &(pAc->PnmiBackup), - sizeof(SK_PNMI_STRUCT_DATA)); - pAc->DiagModeActive = DIAG_NOTACTIVE; - pAc->Pnmi.DiagAttached = SK_DIAG_IDLE; - if (pAc->WasIfUp[0] == SK_TRUE) { - pAc->DiagFlowCtrl = SK_TRUE; /* for SkGeClose */ - DoPrintInterfaceChange = SK_FALSE; - SkDrvInitAdapter(pAc, 0); /* first device */ - } - if (pAc->WasIfUp[1] == SK_TRUE) { - pAc->DiagFlowCtrl = SK_TRUE; /* for SkGeClose */ - DoPrintInterfaceChange = SK_FALSE; - SkDrvInitAdapter(pAc, 1); /* second device */ - } - return(0); -} - -/***************************************************************************** - * - * ParseDeviceNbrFromSlotName - Evaluate PCI device number - * - * Description: - * This function parses the PCI slot name information string and will - * retrieve the devcie number out of it. The slot_name maintianed by - * linux is in the form of '02:0a.0', whereas the first two characters - * represent the bus number in hex (in the sample above this is - * pci bus 0x02) and the next two characters the device number (0x0a). - * - * Returns: - * SK_U32: The device number from the PCI slot name - */ - -static SK_U32 ParseDeviceNbrFromSlotName( -const char *SlotName) /* pointer to pci slot name eg. '02:0a.0' */ -{ - char *CurrCharPos = (char *) SlotName; - int FirstNibble = -1; - int SecondNibble = -1; - SK_U32 Result = 0; - - while (*CurrCharPos != '\0') { - if (*CurrCharPos == ':') { - while (*CurrCharPos != '.') { - CurrCharPos++; - if ( (*CurrCharPos >= '0') && - (*CurrCharPos <= '9')) { - if (FirstNibble == -1) { - /* dec. value for '0' */ - FirstNibble = *CurrCharPos - 48; - } else { - SecondNibble = *CurrCharPos - 48; - } - } else if ( (*CurrCharPos >= 'a') && - (*CurrCharPos <= 'f') ) { - if (FirstNibble == -1) { - FirstNibble = *CurrCharPos - 87; - } else { - SecondNibble = *CurrCharPos - 87; - } - } else { - Result = 0; - } - } - - Result = FirstNibble; - Result = Result << 4; /* first nibble is higher one */ - Result = Result | SecondNibble; - } - CurrCharPos++; /* next character */ - } - return (Result); -} - -/**************************************************************************** - * - * SkDrvDeInitAdapter - deinitialize adapter (this function is only - * called if Diag attaches to that card) - * - * Description: - * Close initialized adapter. - * - * Returns: - * 0 - on success - * error code - on error - */ -static int SkDrvDeInitAdapter( -SK_AC *pAC, /* pointer to adapter context */ -int devNbr) /* what device is to be handled */ -{ - struct SK_NET_DEVICE *dev; - - dev = pAC->dev[devNbr]; - - /* On Linux 2.6 the network driver does NOT mess with reference - ** counts. The driver MUST be able to be unloaded at any time - ** due to the possibility of hotplug. - */ - if (SkGeClose(dev) != 0) { - return (-1); - } - return (0); - -} /* SkDrvDeInitAdapter() */ - -/**************************************************************************** - * - * SkDrvInitAdapter - Initialize adapter (this function is only - * called if Diag deattaches from that card) - * - * Description: - * Close initialized adapter. - * - * Returns: - * 0 - on success - * error code - on error - */ -static int SkDrvInitAdapter( -SK_AC *pAC, /* pointer to adapter context */ -int devNbr) /* what device is to be handled */ -{ - struct SK_NET_DEVICE *dev; - - dev = pAC->dev[devNbr]; - - if (SkGeOpen(dev) != 0) { - return (-1); - } - - /* - ** Use correct MTU size and indicate to kernel TX queue can be started - */ - if (SkGeChangeMtu(dev, dev->mtu) != 0) { - return (-1); - } - return (0); - -} /* SkDrvInitAdapter */ - -#endif - -#ifdef DEBUG -/****************************************************************************/ -/* "debug only" section *****************************************************/ -/****************************************************************************/ - - -/***************************************************************************** - * - * DumpMsg - print a frame - * - * Description: - * This function prints frames to the system logfile/to the console. - * - * Returns: N/A - * - */ -static void DumpMsg(struct sk_buff *skb, char *str) -{ - int msglen; - - if (skb == NULL) { - printk("DumpMsg(): NULL-Message\n"); - return; - } - - if (skb->data == NULL) { - printk("DumpMsg(): Message empty\n"); - return; - } - - msglen = skb->len; - if (msglen > 64) - msglen = 64; - - printk("--- Begin of message from %s , len %d (from %d) ----\n", str, msglen, skb->len); - - DumpData((char *)skb->data, msglen); - - printk("------- End of message ---------\n"); -} /* DumpMsg */ - - - -/***************************************************************************** - * - * DumpData - print a data area - * - * Description: - * This function prints a area of data to the system logfile/to the - * console. - * - * Returns: N/A - * - */ -static void DumpData(char *p, int size) -{ -register int i; -int haddr, addr; -char hex_buffer[180]; -char asc_buffer[180]; -char HEXCHAR[] = "0123456789ABCDEF"; - - addr = 0; - haddr = 0; - hex_buffer[0] = 0; - asc_buffer[0] = 0; - for (i=0; i < size; ) { - if (*p >= '0' && *p <='z') - asc_buffer[addr] = *p; - else - asc_buffer[addr] = '.'; - addr++; - asc_buffer[addr] = 0; - hex_buffer[haddr] = HEXCHAR[(*p & 0xf0) >> 4]; - haddr++; - hex_buffer[haddr] = HEXCHAR[*p & 0x0f]; - haddr++; - hex_buffer[haddr] = ' '; - haddr++; - hex_buffer[haddr] = 0; - p++; - i++; - if (i%16 == 0) { - printk("%s %s\n", hex_buffer, asc_buffer); - addr = 0; - haddr = 0; - } - } -} /* DumpData */ - - -/***************************************************************************** - * - * DumpLong - print a data area as long values - * - * Description: - * This function prints a area of data to the system logfile/to the - * console. - * - * Returns: N/A - * - */ -static void DumpLong(char *pc, int size) -{ -register int i; -int haddr, addr; -char hex_buffer[180]; -char asc_buffer[180]; -char HEXCHAR[] = "0123456789ABCDEF"; -long *p; -int l; - - addr = 0; - haddr = 0; - hex_buffer[0] = 0; - asc_buffer[0] = 0; - p = (long*) pc; - for (i=0; i < size; ) { - l = (long) *p; - hex_buffer[haddr] = HEXCHAR[(l >> 28) & 0xf]; - haddr++; - hex_buffer[haddr] = HEXCHAR[(l >> 24) & 0xf]; - haddr++; - hex_buffer[haddr] = HEXCHAR[(l >> 20) & 0xf]; - haddr++; - hex_buffer[haddr] = HEXCHAR[(l >> 16) & 0xf]; - haddr++; - hex_buffer[haddr] = HEXCHAR[(l >> 12) & 0xf]; - haddr++; - hex_buffer[haddr] = HEXCHAR[(l >> 8) & 0xf]; - haddr++; - hex_buffer[haddr] = HEXCHAR[(l >> 4) & 0xf]; - haddr++; - hex_buffer[haddr] = HEXCHAR[l & 0x0f]; - haddr++; - hex_buffer[haddr] = ' '; - haddr++; - hex_buffer[haddr] = 0; - p++; - i++; - if (i%8 == 0) { - printk("%4x %s\n", (i-8)*4, hex_buffer); - haddr = 0; - } - } - printk("------------------------\n"); -} /* DumpLong */ - -#endif - -static int __devinit skge_probe_one(struct pci_dev *pdev, - const struct pci_device_id *ent) -{ - SK_AC *pAC; - DEV_NET *pNet = NULL; - struct net_device *dev = NULL; - static int boards_found = 0; - int error = -ENODEV; - int using_dac = 0; - char DeviceStr[80]; - - if (pci_enable_device(pdev)) - goto out; - - /* Configure DMA attributes. */ - if (sizeof(dma_addr_t) > sizeof(u32) && - !(error = pci_set_dma_mask(pdev, DMA_64BIT_MASK))) { - using_dac = 1; - error = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK); - if (error < 0) { - printk(KERN_ERR "sk98lin %s unable to obtain 64 bit DMA " - "for consistent allocations\n", pci_name(pdev)); - goto out_disable_device; - } - } else { - error = pci_set_dma_mask(pdev, DMA_32BIT_MASK); - if (error) { - printk(KERN_ERR "sk98lin %s no usable DMA configuration\n", - pci_name(pdev)); - goto out_disable_device; - } - } - - error = -ENOMEM; - dev = alloc_etherdev(sizeof(DEV_NET)); - if (!dev) { - printk(KERN_ERR "sk98lin: unable to allocate etherdev " - "structure!\n"); - goto out_disable_device; - } - - pNet = netdev_priv(dev); - pNet->pAC = kzalloc(sizeof(SK_AC), GFP_KERNEL); - if (!pNet->pAC) { - printk(KERN_ERR "sk98lin: unable to allocate adapter " - "structure!\n"); - goto out_free_netdev; - } - - pAC = pNet->pAC; - pAC->PciDev = pdev; - - pAC->dev[0] = dev; - pAC->dev[1] = dev; - pAC->CheckQueue = SK_FALSE; - - dev->irq = pdev->irq; - - error = SkGeInitPCI(pAC); - if (error) { - printk(KERN_ERR "sk98lin: PCI setup failed: %i\n", error); - goto out_free_netdev; - } - - SET_MODULE_OWNER(dev); - dev->open = &SkGeOpen; - dev->stop = &SkGeClose; - dev->hard_start_xmit = &SkGeXmit; - dev->get_stats = &SkGeStats; - dev->set_multicast_list = &SkGeSetRxMode; - dev->set_mac_address = &SkGeSetMacAddr; - dev->do_ioctl = &SkGeIoctl; - dev->change_mtu = &SkGeChangeMtu; -#ifdef CONFIG_NET_POLL_CONTROLLER - dev->poll_controller = &SkGePollController; -#endif - SET_NETDEV_DEV(dev, &pdev->dev); - SET_ETHTOOL_OPS(dev, &SkGeEthtoolOps); - - /* Use only if yukon hardware */ - if (pAC->ChipsetType) { -#ifdef USE_SK_TX_CHECKSUM - dev->features |= NETIF_F_IP_CSUM; -#endif -#ifdef SK_ZEROCOPY - dev->features |= NETIF_F_SG; -#endif -#ifdef USE_SK_RX_CHECKSUM - pAC->RxPort[0].RxCsum = 1; -#endif - } - - if (using_dac) - dev->features |= NETIF_F_HIGHDMA; - - pAC->Index = boards_found++; - - error = SkGeBoardInit(dev, pAC); - if (error) - goto out_free_netdev; - - /* Read Adapter name from VPD */ - if (ProductStr(pAC, DeviceStr, sizeof(DeviceStr)) != 0) { - error = -EIO; - printk(KERN_ERR "sk98lin: Could not read VPD data.\n"); - goto out_free_resources; - } - - /* Register net device */ - error = register_netdev(dev); - if (error) { - printk(KERN_ERR "sk98lin: Could not register device.\n"); - goto out_free_resources; - } - - /* Print adapter specific string from vpd */ - printk("%s: %s\n", dev->name, DeviceStr); - - /* Print configuration settings */ - printk(" PrefPort:%c RlmtMode:%s\n", - 'A' + pAC->Rlmt.Net[0].Port[pAC->Rlmt.Net[0].PrefPort]->PortNumber, - (pAC->RlmtMode==0) ? "Check Link State" : - ((pAC->RlmtMode==1) ? "Check Link State" : - ((pAC->RlmtMode==3) ? "Check Local Port" : - ((pAC->RlmtMode==7) ? "Check Segmentation" : - ((pAC->RlmtMode==17) ? "Dual Check Link State" :"Error"))))); - - SkGeYellowLED(pAC, pAC->IoBase, 1); - - memcpy(&dev->dev_addr, &pAC->Addr.Net[0].CurrentMacAddress, 6); - memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len); - - pNet->PortNr = 0; - pNet->NetNr = 0; - - boards_found++; - - pci_set_drvdata(pdev, dev); - - /* More then one port found */ - if ((pAC->GIni.GIMacsFound == 2 ) && (pAC->RlmtNets == 2)) { - dev = alloc_etherdev(sizeof(DEV_NET)); - if (!dev) { - printk(KERN_ERR "sk98lin: unable to allocate etherdev " - "structure!\n"); - goto single_port; - } - - pNet = netdev_priv(dev); - pNet->PortNr = 1; - pNet->NetNr = 1; - pNet->pAC = pAC; - - dev->open = &SkGeOpen; - dev->stop = &SkGeClose; - dev->hard_start_xmit = &SkGeXmit; - dev->get_stats = &SkGeStats; - dev->set_multicast_list = &SkGeSetRxMode; - dev->set_mac_address = &SkGeSetMacAddr; - dev->do_ioctl = &SkGeIoctl; - dev->change_mtu = &SkGeChangeMtu; - SET_NETDEV_DEV(dev, &pdev->dev); - SET_ETHTOOL_OPS(dev, &SkGeEthtoolOps); - - if (pAC->ChipsetType) { -#ifdef USE_SK_TX_CHECKSUM - dev->features |= NETIF_F_IP_CSUM; -#endif -#ifdef SK_ZEROCOPY - dev->features |= NETIF_F_SG; -#endif -#ifdef USE_SK_RX_CHECKSUM - pAC->RxPort[1].RxCsum = 1; -#endif - } - - if (using_dac) - dev->features |= NETIF_F_HIGHDMA; - - error = register_netdev(dev); - if (error) { - printk(KERN_ERR "sk98lin: Could not register device" - " for second port. (%d)\n", error); - free_netdev(dev); - goto single_port; - } - - pAC->dev[1] = dev; - memcpy(&dev->dev_addr, - &pAC->Addr.Net[1].CurrentMacAddress, 6); - memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len); - - printk("%s: %s\n", dev->name, DeviceStr); - printk(" PrefPort:B RlmtMode:Dual Check Link State\n"); - } - -single_port: - - /* Save the hardware revision */ - pAC->HWRevision = (((pAC->GIni.GIPciHwRev >> 4) & 0x0F)*10) + - (pAC->GIni.GIPciHwRev & 0x0F); - - /* Set driver globals */ - pAC->Pnmi.pDriverFileName = DRIVER_FILE_NAME; - pAC->Pnmi.pDriverReleaseDate = DRIVER_REL_DATE; - - memset(&pAC->PnmiBackup, 0, sizeof(SK_PNMI_STRUCT_DATA)); - memcpy(&pAC->PnmiBackup, &pAC->PnmiStruct, sizeof(SK_PNMI_STRUCT_DATA)); - - return 0; - - out_free_resources: - FreeResources(dev); - out_free_netdev: - free_netdev(dev); - out_disable_device: - pci_disable_device(pdev); - out: - return error; -} - -static void __devexit skge_remove_one(struct pci_dev *pdev) -{ - struct net_device *dev = pci_get_drvdata(pdev); - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - struct net_device *otherdev = pAC->dev[1]; - - unregister_netdev(dev); - - SkGeYellowLED(pAC, pAC->IoBase, 0); - - if (pAC->BoardLevel == SK_INIT_RUN) { - SK_EVPARA EvPara; - unsigned long Flags; - - /* board is still alive */ - spin_lock_irqsave(&pAC->SlowPathLock, Flags); - EvPara.Para32[0] = 0; - EvPara.Para32[1] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_STOP, EvPara); - EvPara.Para32[0] = 1; - EvPara.Para32[1] = -1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_STOP, EvPara); - SkEventDispatcher(pAC, pAC->IoBase); - /* disable interrupts */ - SK_OUT32(pAC->IoBase, B0_IMSK, 0); - SkGeDeInit(pAC, pAC->IoBase); - spin_unlock_irqrestore(&pAC->SlowPathLock, Flags); - pAC->BoardLevel = SK_INIT_DATA; - /* We do NOT check here, if IRQ was pending, of course*/ - } - - if (pAC->BoardLevel == SK_INIT_IO) { - /* board is still alive */ - SkGeDeInit(pAC, pAC->IoBase); - pAC->BoardLevel = SK_INIT_DATA; - } - - FreeResources(dev); - free_netdev(dev); - if (otherdev != dev) - free_netdev(otherdev); - kfree(pAC); -} - -#ifdef CONFIG_PM -static int skge_suspend(struct pci_dev *pdev, pm_message_t state) -{ - struct net_device *dev = pci_get_drvdata(pdev); - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - struct net_device *otherdev = pAC->dev[1]; - - if (netif_running(dev)) { - netif_carrier_off(dev); - DoPrintInterfaceChange = SK_FALSE; - SkDrvDeInitAdapter(pAC, 0); /* performs SkGeClose */ - netif_device_detach(dev); - } - if (otherdev != dev) { - if (netif_running(otherdev)) { - netif_carrier_off(otherdev); - DoPrintInterfaceChange = SK_FALSE; - SkDrvDeInitAdapter(pAC, 1); /* performs SkGeClose */ - netif_device_detach(otherdev); - } - } - - pci_save_state(pdev); - pci_enable_wake(pdev, pci_choose_state(pdev, state), 0); - if (pAC->AllocFlag & SK_ALLOC_IRQ) { - free_irq(dev->irq, dev); - } - pci_disable_device(pdev); - pci_set_power_state(pdev, pci_choose_state(pdev, state)); - - return 0; -} - -static int skge_resume(struct pci_dev *pdev) -{ - struct net_device *dev = pci_get_drvdata(pdev); - DEV_NET *pNet = netdev_priv(dev); - SK_AC *pAC = pNet->pAC; - struct net_device *otherdev = pAC->dev[1]; - int ret; - - pci_set_power_state(pdev, PCI_D0); - pci_restore_state(pdev); - ret = pci_enable_device(pdev); - if (ret) { - printk(KERN_WARNING "sk98lin: unable to enable device %s " - "in resume\n", dev->name); - goto err_out; - } - pci_set_master(pdev); - if (pAC->GIni.GIMacsFound == 2) - ret = request_irq(dev->irq, SkGeIsr, IRQF_SHARED, "sk98lin", dev); - else - ret = request_irq(dev->irq, SkGeIsrOnePort, IRQF_SHARED, "sk98lin", dev); - if (ret) { - printk(KERN_WARNING "sk98lin: unable to acquire IRQ %d\n", dev->irq); - ret = -EBUSY; - goto err_out_disable_pdev; - } - - netif_device_attach(dev); - if (netif_running(dev)) { - DoPrintInterfaceChange = SK_FALSE; - SkDrvInitAdapter(pAC, 0); /* first device */ - } - if (otherdev != dev) { - netif_device_attach(otherdev); - if (netif_running(otherdev)) { - DoPrintInterfaceChange = SK_FALSE; - SkDrvInitAdapter(pAC, 1); /* second device */ - } - } - - return 0; - -err_out_disable_pdev: - pci_disable_device(pdev); -err_out: - pAC->AllocFlag &= ~SK_ALLOC_IRQ; - dev->irq = 0; - return ret; -} -#else -#define skge_suspend NULL -#define skge_resume NULL -#endif - -static struct pci_device_id skge_pci_tbl[] = { - { PCI_VENDOR_ID_3COM, 0x1700, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - { PCI_VENDOR_ID_3COM, 0x80eb, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - { PCI_VENDOR_ID_SYSKONNECT, 0x4300, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - { PCI_VENDOR_ID_SYSKONNECT, 0x4320, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, -/* DLink card does not have valid VPD so this driver gags - * { PCI_VENDOR_ID_DLINK, 0x4c00, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - */ - { PCI_VENDOR_ID_MARVELL, 0x4320, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - { PCI_VENDOR_ID_MARVELL, 0x5005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - { PCI_VENDOR_ID_CNET, 0x434e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015, }, - { PCI_VENDOR_ID_LINKSYS, 0x1064, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, - { 0 } -}; - -MODULE_DEVICE_TABLE(pci, skge_pci_tbl); - -static struct pci_driver skge_driver = { - .name = "sk98lin", - .id_table = skge_pci_tbl, - .probe = skge_probe_one, - .remove = __devexit_p(skge_remove_one), - .suspend = skge_suspend, - .resume = skge_resume, -}; - -static int __init skge_init(void) -{ - printk(KERN_NOTICE "sk98lin: driver has been replaced by the skge driver" - " and is scheduled for removal\n"); - - return pci_register_driver(&skge_driver); -} - -static void __exit skge_exit(void) -{ - pci_unregister_driver(&skge_driver); -} - -module_init(skge_init); -module_exit(skge_exit); diff --git a/drivers/net/sk98lin/skgehwt.c b/drivers/net/sk98lin/skgehwt.c deleted file mode 100644 index db670993c2df..000000000000 --- a/drivers/net/sk98lin/skgehwt.c +++ /dev/null @@ -1,171 +0,0 @@ -/****************************************************************************** - * - * Name: skgehwt.c - * Project: Gigabit Ethernet Adapters, Event Scheduler Module - * Version: $Revision: 1.15 $ - * Date: $Date: 2003/09/16 13:41:23 $ - * Purpose: Hardware Timer - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * Event queue and dispatcher - */ -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: skgehwt.c,v 1.15 2003/09/16 13:41:23 rschmidt Exp $ (C) Marvell."; -#endif - -#include "h/skdrv1st.h" /* Driver Specific Definitions */ -#include "h/skdrv2nd.h" /* Adapter Control- and Driver specific Def. */ - -#ifdef __C2MAN__ -/* - * Hardware Timer function queue management. - */ -intro() -{} -#endif - -/* - * Prototypes of local functions. - */ -#define SK_HWT_MAX (65000) - -/* correction factor */ -#define SK_HWT_FAC (1000 * (SK_U32)pAC->GIni.GIHstClkFact / 100) - -/* - * Initialize hardware timer. - * - * Must be called during init level 1. - */ -void SkHwtInit( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc) /* IoContext */ -{ - pAC->Hwt.TStart = 0 ; - pAC->Hwt.TStop = 0 ; - pAC->Hwt.TActive = SK_FALSE; - - SkHwtStop(pAC, Ioc); -} - -/* - * - * Start hardware timer (clock ticks are 16us). - * - */ -void SkHwtStart( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc, /* IoContext */ -SK_U32 Time) /* Time in units of 16us to load the timer with. */ -{ - SK_U32 Cnt; - - if (Time > SK_HWT_MAX) - Time = SK_HWT_MAX; - - pAC->Hwt.TStart = Time; - pAC->Hwt.TStop = 0L; - - Cnt = Time; - - /* - * if time < 16 us - * time = 16 us - */ - if (!Cnt) { - Cnt++; - } - - SK_OUT32(Ioc, B2_TI_INI, Cnt * SK_HWT_FAC); - - SK_OUT16(Ioc, B2_TI_CTRL, TIM_START); /* Start timer. */ - - pAC->Hwt.TActive = SK_TRUE; -} - -/* - * Stop hardware timer. - * and clear the timer IRQ - */ -void SkHwtStop( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc) /* IoContext */ -{ - SK_OUT16(Ioc, B2_TI_CTRL, TIM_STOP); - - SK_OUT16(Ioc, B2_TI_CTRL, TIM_CLR_IRQ); - - pAC->Hwt.TActive = SK_FALSE; -} - - -/* - * Stop hardware timer and read time elapsed since last start. - * - * returns - * The elapsed time since last start in units of 16us. - * - */ -SK_U32 SkHwtRead( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc) /* IoContext */ -{ - SK_U32 TRead; - SK_U32 IStatus; - - if (pAC->Hwt.TActive) { - - SkHwtStop(pAC, Ioc); - - SK_IN32(Ioc, B2_TI_VAL, &TRead); - TRead /= SK_HWT_FAC; - - SK_IN32(Ioc, B0_ISRC, &IStatus); - - /* Check if timer expired (or wraped around) */ - if ((TRead > pAC->Hwt.TStart) || (IStatus & IS_TIMINT)) { - - SkHwtStop(pAC, Ioc); - - pAC->Hwt.TStop = pAC->Hwt.TStart; - } - else { - - pAC->Hwt.TStop = pAC->Hwt.TStart - TRead; - } - } - return(pAC->Hwt.TStop); -} - -/* - * interrupt source= timer - */ -void SkHwtIsr( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc) /* IoContext */ -{ - SkHwtStop(pAC, Ioc); - - pAC->Hwt.TStop = pAC->Hwt.TStart; - - SkTimerDone(pAC, Ioc); -} - -/* End of file */ diff --git a/drivers/net/sk98lin/skgeinit.c b/drivers/net/sk98lin/skgeinit.c deleted file mode 100644 index 67f1d6a5c15d..000000000000 --- a/drivers/net/sk98lin/skgeinit.c +++ /dev/null @@ -1,2005 +0,0 @@ -/****************************************************************************** - * - * Name: skgeinit.c - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.97 $ - * Date: $Date: 2003/10/02 16:45:31 $ - * Purpose: Contains functions to initialize the adapter - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#include "h/skdrv1st.h" -#include "h/skdrv2nd.h" - -/* global variables ***********************************************************/ - -/* local variables ************************************************************/ - -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: skgeinit.c,v 1.97 2003/10/02 16:45:31 rschmidt Exp $ (C) Marvell."; -#endif - -struct s_QOffTab { - int RxQOff; /* Receive Queue Address Offset */ - int XsQOff; /* Sync Tx Queue Address Offset */ - int XaQOff; /* Async Tx Queue Address Offset */ -}; -static struct s_QOffTab QOffTab[] = { - {Q_R1, Q_XS1, Q_XA1}, {Q_R2, Q_XS2, Q_XA2} -}; - -struct s_Config { - char ScanString[8]; - SK_U32 Value; -}; - -static struct s_Config OemConfig = { - {'O','E','M','_','C','o','n','f'}, -#ifdef SK_OEM_CONFIG - OEM_CONFIG_VALUE, -#else - 0, -#endif -}; - -/****************************************************************************** - * - * SkGePollTxD() - Enable / Disable Descriptor Polling of TxD Rings - * - * Description: - * Enable or disable the descriptor polling of the transmit descriptor - * ring(s) (TxD) for port 'Port'. - * The new configuration is *not* saved over any SkGeStopPort() and - * SkGeInitPort() calls. - * - * Returns: - * nothing - */ -void SkGePollTxD( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL PollTxD) /* SK_TRUE (enable pol.), SK_FALSE (disable pol.) */ -{ - SK_GEPORT *pPrt; - SK_U32 DWord; - - pPrt = &pAC->GIni.GP[Port]; - - DWord = (SK_U32)(PollTxD ? CSR_ENA_POL : CSR_DIS_POL); - - if (pPrt->PXSQSize != 0) { - SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), DWord); - } - - if (pPrt->PXAQSize != 0) { - SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), DWord); - } -} /* SkGePollTxD */ - - -/****************************************************************************** - * - * SkGeYellowLED() - Switch the yellow LED on or off. - * - * Description: - * Switch the yellow LED on or off. - * - * Note: - * This function may be called any time after SkGeInit(Level 1). - * - * Returns: - * nothing - */ -void SkGeYellowLED( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int State) /* yellow LED state, 0 = OFF, 0 != ON */ -{ - if (State == 0) { - /* Switch yellow LED OFF */ - SK_OUT8(IoC, B0_LED, LED_STAT_OFF); - } - else { - /* Switch yellow LED ON */ - SK_OUT8(IoC, B0_LED, LED_STAT_ON); - } -} /* SkGeYellowLED */ - - -#if (!defined(SK_SLIM) || defined(GENESIS)) -/****************************************************************************** - * - * SkGeXmitLED() - Modify the Operational Mode of a transmission LED. - * - * Description: - * The Rx or Tx LED which is specified by 'Led' will be - * enabled, disabled or switched on in test mode. - * - * Note: - * 'Led' must contain the address offset of the LEDs INI register. - * - * Usage: - * SkGeXmitLED(pAC, IoC, MR_ADDR(Port, TX_LED_INI), SK_LED_ENA); - * - * Returns: - * nothing - */ -void SkGeXmitLED( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Led, /* offset to the LED Init Value register */ -int Mode) /* Mode may be SK_LED_DIS, SK_LED_ENA, SK_LED_TST */ -{ - SK_U32 LedIni; - - switch (Mode) { - case SK_LED_ENA: - LedIni = SK_XMIT_DUR * (SK_U32)pAC->GIni.GIHstClkFact / 100; - SK_OUT32(IoC, Led + XMIT_LED_INI, LedIni); - SK_OUT8(IoC, Led + XMIT_LED_CTRL, LED_START); - break; - case SK_LED_TST: - SK_OUT8(IoC, Led + XMIT_LED_TST, LED_T_ON); - SK_OUT32(IoC, Led + XMIT_LED_CNT, 100); - SK_OUT8(IoC, Led + XMIT_LED_CTRL, LED_START); - break; - case SK_LED_DIS: - default: - /* - * Do NOT stop the LED Timer here. The LED might be - * in on state. But it needs to go off. - */ - SK_OUT32(IoC, Led + XMIT_LED_CNT, 0); - SK_OUT8(IoC, Led + XMIT_LED_TST, LED_T_OFF); - break; - } - - /* - * 1000BT: The Transmit LED is driven by the PHY. - * But the default LED configuration is used for - * Level One and Broadcom PHYs. - * (Broadcom: It may be that PHY_B_PEC_EN_LTR has to be set.) - * (In this case it has to be added here. But we will see. XXX) - */ -} /* SkGeXmitLED */ -#endif /* !SK_SLIM || GENESIS */ - - -/****************************************************************************** - * - * DoCalcAddr() - Calculates the start and the end address of a queue. - * - * Description: - * This function calculates the start and the end address of a queue. - * Afterwards the 'StartVal' is incremented to the next start position. - * If the port is already initialized the calculated values - * will be checked against the configured values and an - * error will be returned, if they are not equal. - * If the port is not initialized the values will be written to - * *StartAdr and *EndAddr. - * - * Returns: - * 0: success - * 1: configuration error - */ -static int DoCalcAddr( -SK_AC *pAC, /* adapter context */ -SK_GEPORT SK_FAR *pPrt, /* port index */ -int QuSize, /* size of the queue to configure in kB */ -SK_U32 SK_FAR *StartVal, /* start value for address calculation */ -SK_U32 SK_FAR *QuStartAddr,/* start addr to calculate */ -SK_U32 SK_FAR *QuEndAddr) /* end address to calculate */ -{ - SK_U32 EndVal; - SK_U32 NextStart; - int Rtv; - - Rtv = 0; - if (QuSize == 0) { - EndVal = *StartVal; - NextStart = EndVal; - } - else { - EndVal = *StartVal + ((SK_U32)QuSize * 1024) - 1; - NextStart = EndVal + 1; - } - - if (pPrt->PState >= SK_PRT_INIT) { - if (*StartVal != *QuStartAddr || EndVal != *QuEndAddr) { - Rtv = 1; - } - } - else { - *QuStartAddr = *StartVal; - *QuEndAddr = EndVal; - } - - *StartVal = NextStart; - return(Rtv); -} /* DoCalcAddr */ - -/****************************************************************************** - * - * SkGeInitAssignRamToQueues() - allocate default queue sizes - * - * Description: - * This function assigns the memory to the different queues and ports. - * When DualNet is set to SK_TRUE all ports get the same amount of memory. - * Otherwise the first port gets most of the memory and all the - * other ports just the required minimum. - * This function can only be called when pAC->GIni.GIRamSize and - * pAC->GIni.GIMacsFound have been initialized, usually this happens - * at init level 1 - * - * Returns: - * 0 - ok - * 1 - invalid input values - * 2 - not enough memory - */ - -int SkGeInitAssignRamToQueues( -SK_AC *pAC, /* Adapter context */ -int ActivePort, /* Active Port in RLMT mode */ -SK_BOOL DualNet) /* adapter context */ -{ - int i; - int UsedKilobytes; /* memory already assigned */ - int ActivePortKilobytes; /* memory available for active port */ - SK_GEPORT *pGePort; - - UsedKilobytes = 0; - - if (ActivePort >= pAC->GIni.GIMacsFound) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_INIT, - ("SkGeInitAssignRamToQueues: ActivePort (%d) invalid\n", - ActivePort)); - return(1); - } - if (((pAC->GIni.GIMacsFound * (SK_MIN_RXQ_SIZE + SK_MIN_TXQ_SIZE)) + - ((RAM_QUOTA_SYNC == 0) ? 0 : SK_MIN_TXQ_SIZE)) > pAC->GIni.GIRamSize) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_INIT, - ("SkGeInitAssignRamToQueues: Not enough memory (%d)\n", - pAC->GIni.GIRamSize)); - return(2); - } - - if (DualNet) { - /* every port gets the same amount of memory */ - ActivePortKilobytes = pAC->GIni.GIRamSize / pAC->GIni.GIMacsFound; - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - - pGePort = &pAC->GIni.GP[i]; - - /* take away the minimum memory for active queues */ - ActivePortKilobytes -= (SK_MIN_RXQ_SIZE + SK_MIN_TXQ_SIZE); - - /* receive queue gets the minimum + 80% of the rest */ - pGePort->PRxQSize = (int) (ROUND_QUEUE_SIZE_KB(( - ActivePortKilobytes * (unsigned long) RAM_QUOTA_RX) / 100)) - + SK_MIN_RXQ_SIZE; - - ActivePortKilobytes -= (pGePort->PRxQSize - SK_MIN_RXQ_SIZE); - - /* synchronous transmit queue */ - pGePort->PXSQSize = 0; - - /* asynchronous transmit queue */ - pGePort->PXAQSize = (int) ROUND_QUEUE_SIZE_KB(ActivePortKilobytes + - SK_MIN_TXQ_SIZE); - } - } - else { - /* Rlmt Mode or single link adapter */ - - /* Set standby queue size defaults for all standby ports */ - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - - if (i != ActivePort) { - pGePort = &pAC->GIni.GP[i]; - - pGePort->PRxQSize = SK_MIN_RXQ_SIZE; - pGePort->PXAQSize = SK_MIN_TXQ_SIZE; - pGePort->PXSQSize = 0; - - /* Count used RAM */ - UsedKilobytes += pGePort->PRxQSize + pGePort->PXAQSize; - } - } - /* what's left? */ - ActivePortKilobytes = pAC->GIni.GIRamSize - UsedKilobytes; - - /* assign it to the active port */ - /* first take away the minimum memory */ - ActivePortKilobytes -= (SK_MIN_RXQ_SIZE + SK_MIN_TXQ_SIZE); - pGePort = &pAC->GIni.GP[ActivePort]; - - /* receive queue get's the minimum + 80% of the rest */ - pGePort->PRxQSize = (int) (ROUND_QUEUE_SIZE_KB((ActivePortKilobytes * - (unsigned long) RAM_QUOTA_RX) / 100)) + SK_MIN_RXQ_SIZE; - - ActivePortKilobytes -= (pGePort->PRxQSize - SK_MIN_RXQ_SIZE); - - /* synchronous transmit queue */ - pGePort->PXSQSize = 0; - - /* asynchronous transmit queue */ - pGePort->PXAQSize = (int) ROUND_QUEUE_SIZE_KB(ActivePortKilobytes) + - SK_MIN_TXQ_SIZE; - } -#ifdef VCPU - VCPUprintf(0, "PRxQSize=%u, PXSQSize=%u, PXAQSize=%u\n", - pGePort->PRxQSize, pGePort->PXSQSize, pGePort->PXAQSize); -#endif /* VCPU */ - - return(0); -} /* SkGeInitAssignRamToQueues */ - -/****************************************************************************** - * - * SkGeCheckQSize() - Checks the Adapters Queue Size Configuration - * - * Description: - * This function verifies the Queue Size Configuration specified - * in the variables PRxQSize, PXSQSize, and PXAQSize of all - * used ports. - * This requirements must be fullfilled to have a valid configuration: - * - The size of all queues must not exceed GIRamSize. - * - The queue sizes must be specified in units of 8 kB. - * - The size of Rx queues of available ports must not be - * smaller than 16 kB. - * - The size of at least one Tx queue (synch. or asynch.) - * of available ports must not be smaller than 16 kB - * when Jumbo Frames are used. - * - The RAM start and end addresses must not be changed - * for ports which are already initialized. - * Furthermore SkGeCheckQSize() defines the Start and End Addresses - * of all ports and stores them into the HWAC port structure. - * - * Returns: - * 0: Queue Size Configuration valid - * 1: Queue Size Configuration invalid - */ -static int SkGeCheckQSize( -SK_AC *pAC, /* adapter context */ -int Port) /* port index */ -{ - SK_GEPORT *pPrt; - int i; - int Rtv; - int Rtv2; - SK_U32 StartAddr; -#ifndef SK_SLIM - int UsedMem; /* total memory used (max. found ports) */ -#endif - - Rtv = 0; - -#ifndef SK_SLIM - - UsedMem = 0; - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - pPrt = &pAC->GIni.GP[i]; - - if ((pPrt->PRxQSize & QZ_UNITS) != 0 || - (pPrt->PXSQSize & QZ_UNITS) != 0 || - (pPrt->PXAQSize & QZ_UNITS) != 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E012, SKERR_HWI_E012MSG); - return(1); - } - - if (i == Port && pPrt->PRxQSize < SK_MIN_RXQ_SIZE) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E011, SKERR_HWI_E011MSG); - return(1); - } - - /* - * the size of at least one Tx queue (synch. or asynch.) has to be > 0. - * if Jumbo Frames are used, this size has to be >= 16 kB. - */ - if ((i == Port && pPrt->PXSQSize == 0 && pPrt->PXAQSize == 0) || - (pAC->GIni.GIPortUsage == SK_JUMBO_LINK && - ((pPrt->PXSQSize > 0 && pPrt->PXSQSize < SK_MIN_TXQ_SIZE) || - (pPrt->PXAQSize > 0 && pPrt->PXAQSize < SK_MIN_TXQ_SIZE)))) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E023, SKERR_HWI_E023MSG); - return(1); - } - - UsedMem += pPrt->PRxQSize + pPrt->PXSQSize + pPrt->PXAQSize; - } - - if (UsedMem > pAC->GIni.GIRamSize) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E012, SKERR_HWI_E012MSG); - return(1); - } -#endif /* !SK_SLIM */ - - /* Now start address calculation */ - StartAddr = pAC->GIni.GIRamOffs; - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - pPrt = &pAC->GIni.GP[i]; - - /* Calculate/Check values for the receive queue */ - Rtv2 = DoCalcAddr(pAC, pPrt, pPrt->PRxQSize, &StartAddr, - &pPrt->PRxQRamStart, &pPrt->PRxQRamEnd); - Rtv |= Rtv2; - - /* Calculate/Check values for the synchronous Tx queue */ - Rtv2 = DoCalcAddr(pAC, pPrt, pPrt->PXSQSize, &StartAddr, - &pPrt->PXsQRamStart, &pPrt->PXsQRamEnd); - Rtv |= Rtv2; - - /* Calculate/Check values for the asynchronous Tx queue */ - Rtv2 = DoCalcAddr(pAC, pPrt, pPrt->PXAQSize, &StartAddr, - &pPrt->PXaQRamStart, &pPrt->PXaQRamEnd); - Rtv |= Rtv2; - - if (Rtv) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E013, SKERR_HWI_E013MSG); - return(1); - } - } - - return(0); -} /* SkGeCheckQSize */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkGeInitMacArb() - Initialize the MAC Arbiter - * - * Description: - * This function initializes the MAC Arbiter. - * It must not be called if there is still an - * initialized or active port. - * - * Returns: - * nothing - */ -static void SkGeInitMacArb( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC) /* IO context */ -{ - /* release local reset */ - SK_OUT16(IoC, B3_MA_TO_CTRL, MA_RST_CLR); - - /* configure timeout values */ - SK_OUT8(IoC, B3_MA_TOINI_RX1, SK_MAC_TO_53); - SK_OUT8(IoC, B3_MA_TOINI_RX2, SK_MAC_TO_53); - SK_OUT8(IoC, B3_MA_TOINI_TX1, SK_MAC_TO_53); - SK_OUT8(IoC, B3_MA_TOINI_TX2, SK_MAC_TO_53); - - SK_OUT8(IoC, B3_MA_RCINI_RX1, 0); - SK_OUT8(IoC, B3_MA_RCINI_RX2, 0); - SK_OUT8(IoC, B3_MA_RCINI_TX1, 0); - SK_OUT8(IoC, B3_MA_RCINI_TX2, 0); - - /* recovery values are needed for XMAC II Rev. B2 only */ - /* Fast Output Enable Mode was intended to use with Rev. B2, but now? */ - - /* - * There is no start or enable button to push, therefore - * the MAC arbiter is configured and enabled now. - */ -} /* SkGeInitMacArb */ - - -/****************************************************************************** - * - * SkGeInitPktArb() - Initialize the Packet Arbiter - * - * Description: - * This function initializes the Packet Arbiter. - * It must not be called if there is still an - * initialized or active port. - * - * Returns: - * nothing - */ -static void SkGeInitPktArb( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC) /* IO context */ -{ - /* release local reset */ - SK_OUT16(IoC, B3_PA_CTRL, PA_RST_CLR); - - /* configure timeout values */ - SK_OUT16(IoC, B3_PA_TOINI_RX1, SK_PKT_TO_MAX); - SK_OUT16(IoC, B3_PA_TOINI_RX2, SK_PKT_TO_MAX); - SK_OUT16(IoC, B3_PA_TOINI_TX1, SK_PKT_TO_MAX); - SK_OUT16(IoC, B3_PA_TOINI_TX2, SK_PKT_TO_MAX); - - /* - * enable timeout timers if jumbo frames not used - * NOTE: the packet arbiter timeout interrupt is needed for - * half duplex hangup workaround - */ - if (pAC->GIni.GIPortUsage != SK_JUMBO_LINK) { - if (pAC->GIni.GIMacsFound == 1) { - SK_OUT16(IoC, B3_PA_CTRL, PA_ENA_TO_TX1); - } - else { - SK_OUT16(IoC, B3_PA_CTRL, PA_ENA_TO_TX1 | PA_ENA_TO_TX2); - } - } -} /* SkGeInitPktArb */ -#endif /* GENESIS */ - - -/****************************************************************************** - * - * SkGeInitMacFifo() - Initialize the MAC FIFOs - * - * Description: - * Initialize all MAC FIFOs of the specified port - * - * Returns: - * nothing - */ -static void SkGeInitMacFifo( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U16 Word; -#ifdef VCPU - SK_U32 DWord; -#endif /* VCPU */ - /* - * For each FIFO: - * - release local reset - * - use default value for MAC FIFO size - * - setup defaults for the control register - * - enable the FIFO - */ - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* Configure Rx MAC FIFO */ - SK_OUT8(IoC, MR_ADDR(Port, RX_MFF_CTRL2), MFF_RST_CLR); - SK_OUT16(IoC, MR_ADDR(Port, RX_MFF_CTRL1), MFF_RX_CTRL_DEF); - SK_OUT8(IoC, MR_ADDR(Port, RX_MFF_CTRL2), MFF_ENA_OP_MD); - - /* Configure Tx MAC FIFO */ - SK_OUT8(IoC, MR_ADDR(Port, TX_MFF_CTRL2), MFF_RST_CLR); - SK_OUT16(IoC, MR_ADDR(Port, TX_MFF_CTRL1), MFF_TX_CTRL_DEF); - SK_OUT8(IoC, MR_ADDR(Port, TX_MFF_CTRL2), MFF_ENA_OP_MD); - - /* Enable frame flushing if jumbo frames used */ - if (pAC->GIni.GIPortUsage == SK_JUMBO_LINK) { - SK_OUT16(IoC, MR_ADDR(Port, RX_MFF_CTRL1), MFF_ENA_FLUSH); - } - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* set Rx GMAC FIFO Flush Mask */ - SK_OUT16(IoC, MR_ADDR(Port, RX_GMF_FL_MSK), (SK_U16)RX_FF_FL_DEF_MSK); - - Word = (SK_U16)GMF_RX_CTRL_DEF; - - /* disable Rx GMAC FIFO Flush for YUKON-Lite Rev. A0 only */ - if (pAC->GIni.GIYukonLite && pAC->GIni.GIChipId == CHIP_ID_YUKON) { - - Word &= ~GMF_RX_F_FL_ON; - } - - /* Configure Rx MAC FIFO */ - SK_OUT8(IoC, MR_ADDR(Port, RX_GMF_CTRL_T), (SK_U8)GMF_RST_CLR); - SK_OUT16(IoC, MR_ADDR(Port, RX_GMF_CTRL_T), Word); - - /* set Rx GMAC FIFO Flush Threshold (default: 0x0a -> 56 bytes) */ - SK_OUT16(IoC, MR_ADDR(Port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF); - - /* Configure Tx MAC FIFO */ - SK_OUT8(IoC, MR_ADDR(Port, TX_GMF_CTRL_T), (SK_U8)GMF_RST_CLR); - SK_OUT16(IoC, MR_ADDR(Port, TX_GMF_CTRL_T), (SK_U16)GMF_TX_CTRL_DEF); - -#ifdef VCPU - SK_IN32(IoC, MR_ADDR(Port, RX_GMF_AF_THR), &DWord); - SK_IN32(IoC, MR_ADDR(Port, TX_GMF_AE_THR), &DWord); -#endif /* VCPU */ - - /* set Tx GMAC FIFO Almost Empty Threshold */ -/* SK_OUT32(IoC, MR_ADDR(Port, TX_GMF_AE_THR), 0); */ - } -#endif /* YUKON */ - -} /* SkGeInitMacFifo */ - -#ifdef SK_LNK_SYNC_CNT -/****************************************************************************** - * - * SkGeLoadLnkSyncCnt() - Load the Link Sync Counter and starts counting - * - * Description: - * This function starts the Link Sync Counter of the specified - * port and enables the generation of an Link Sync IRQ. - * The Link Sync Counter may be used to detect an active link, - * if autonegotiation is not used. - * - * Note: - * o To ensure receiving the Link Sync Event the LinkSyncCounter - * should be initialized BEFORE clearing the XMAC's reset! - * o Enable IS_LNK_SYNC_M1 and IS_LNK_SYNC_M2 after calling this - * function. - * - * Returns: - * nothing - */ -void SkGeLoadLnkSyncCnt( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_U32 CntVal) /* Counter value */ -{ - SK_U32 OrgIMsk; - SK_U32 NewIMsk; - SK_U32 ISrc; - SK_BOOL IrqPend; - - /* stop counter */ - SK_OUT8(IoC, MR_ADDR(Port, LNK_SYNC_CTRL), LED_STOP); - - /* - * ASIC problem: - * Each time starting the Link Sync Counter an IRQ is generated - * by the adapter. See problem report entry from 21.07.98 - * - * Workaround: Disable Link Sync IRQ and clear the unexpeced IRQ - * if no IRQ is already pending. - */ - IrqPend = SK_FALSE; - SK_IN32(IoC, B0_ISRC, &ISrc); - SK_IN32(IoC, B0_IMSK, &OrgIMsk); - if (Port == MAC_1) { - NewIMsk = OrgIMsk & ~IS_LNK_SYNC_M1; - if ((ISrc & IS_LNK_SYNC_M1) != 0) { - IrqPend = SK_TRUE; - } - } - else { - NewIMsk = OrgIMsk & ~IS_LNK_SYNC_M2; - if ((ISrc & IS_LNK_SYNC_M2) != 0) { - IrqPend = SK_TRUE; - } - } - if (!IrqPend) { - SK_OUT32(IoC, B0_IMSK, NewIMsk); - } - - /* load counter */ - SK_OUT32(IoC, MR_ADDR(Port, LNK_SYNC_INI), CntVal); - - /* start counter */ - SK_OUT8(IoC, MR_ADDR(Port, LNK_SYNC_CTRL), LED_START); - - if (!IrqPend) { - /* clear the unexpected IRQ, and restore the interrupt mask */ - SK_OUT8(IoC, MR_ADDR(Port, LNK_SYNC_CTRL), LED_CLR_IRQ); - SK_OUT32(IoC, B0_IMSK, OrgIMsk); - } -} /* SkGeLoadLnkSyncCnt*/ -#endif /* SK_LNK_SYNC_CNT */ - -#if defined(SK_DIAG) || defined(SK_CFG_SYNC) -/****************************************************************************** - * - * SkGeCfgSync() - Configure synchronous bandwidth for this port. - * - * Description: - * This function may be used to configure synchronous bandwidth - * to the specified port. This may be done any time after - * initializing the port. The configuration values are NOT saved - * in the HWAC port structure and will be overwritten any - * time when stopping and starting the port. - * Any values for the synchronous configuration will be ignored - * if the size of the synchronous queue is zero! - * - * The default configuration for the synchronous service is - * TXA_ENA_FSYNC. This means if the size of - * the synchronous queue is unequal zero but no specific - * synchronous bandwidth is configured, the synchronous queue - * will always have the 'unlimited' transmit priority! - * - * This mode will be restored if the synchronous bandwidth is - * deallocated ('IntTime' = 0 and 'LimCount' = 0). - * - * Returns: - * 0: success - * 1: parameter configuration error - * 2: try to configure quality of service although no - * synchronous queue is configured - */ -int SkGeCfgSync( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_U32 IntTime, /* Interval Timer Value in units of 8ns */ -SK_U32 LimCount, /* Number of bytes to transfer during IntTime */ -int SyncMode) /* Sync Mode: TXA_ENA_ALLOC | TXA_DIS_ALLOC | 0 */ -{ - int Rtv; - - Rtv = 0; - - /* check the parameters */ - if (LimCount > IntTime || - (LimCount == 0 && IntTime != 0) || - (LimCount != 0 && IntTime == 0)) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E010, SKERR_HWI_E010MSG); - return(1); - } - - if (pAC->GIni.GP[Port].PXSQSize == 0) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E009, SKERR_HWI_E009MSG); - return(2); - } - - /* calculate register values */ - IntTime = (IntTime / 2) * pAC->GIni.GIHstClkFact / 100; - LimCount = LimCount / 8; - - if (IntTime > TXA_MAX_VAL || LimCount > TXA_MAX_VAL) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E010, SKERR_HWI_E010MSG); - return(1); - } - - /* - * - Enable 'Force Sync' to ensure the synchronous queue - * has the priority while configuring the new values. - * - Also 'disable alloc' to ensure the settings complies - * to the SyncMode parameter. - * - Disable 'Rate Control' to configure the new values. - * - write IntTime and LimCount - * - start 'Rate Control' and disable 'Force Sync' - * if Interval Timer or Limit Counter not zero. - */ - SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), - TXA_ENA_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC); - - SK_OUT32(IoC, MR_ADDR(Port, TXA_ITI_INI), IntTime); - SK_OUT32(IoC, MR_ADDR(Port, TXA_LIM_INI), LimCount); - - SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), - (SK_U8)(SyncMode & (TXA_ENA_ALLOC | TXA_DIS_ALLOC))); - - if (IntTime != 0 || LimCount != 0) { - SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), TXA_DIS_FSYNC | TXA_START_RC); - } - - return(0); -} /* SkGeCfgSync */ -#endif /* SK_DIAG || SK_CFG_SYNC*/ - - -/****************************************************************************** - * - * DoInitRamQueue() - Initialize the RAM Buffer Address of a single Queue - * - * Desccription: - * If the queue is used, enable and initialize it. - * Make sure the queue is still reset, if it is not used. - * - * Returns: - * nothing - */ -static void DoInitRamQueue( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int QuIoOffs, /* Queue IO Address Offset */ -SK_U32 QuStartAddr, /* Queue Start Address */ -SK_U32 QuEndAddr, /* Queue End Address */ -int QuType) /* Queue Type (SK_RX_SRAM_Q|SK_RX_BRAM_Q|SK_TX_RAM_Q) */ -{ - SK_U32 RxUpThresVal; - SK_U32 RxLoThresVal; - - if (QuStartAddr != QuEndAddr) { - /* calculate thresholds, assume we have a big Rx queue */ - RxUpThresVal = (QuEndAddr + 1 - QuStartAddr - SK_RB_ULPP) / 8; - RxLoThresVal = (QuEndAddr + 1 - QuStartAddr - SK_RB_LLPP_B)/8; - - /* build HW address format */ - QuStartAddr = QuStartAddr / 8; - QuEndAddr = QuEndAddr / 8; - - /* release local reset */ - SK_OUT8(IoC, RB_ADDR(QuIoOffs, RB_CTRL), RB_RST_CLR); - - /* configure addresses */ - SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_START), QuStartAddr); - SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_END), QuEndAddr); - SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_WP), QuStartAddr); - SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_RP), QuStartAddr); - - switch (QuType) { - case SK_RX_SRAM_Q: - /* configure threshold for small Rx Queue */ - RxLoThresVal += (SK_RB_LLPP_B - SK_RB_LLPP_S) / 8; - - /* continue with SK_RX_BRAM_Q */ - case SK_RX_BRAM_Q: - /* write threshold for Rx Queue */ - - SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_RX_UTPP), RxUpThresVal); - SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_RX_LTPP), RxLoThresVal); - - /* the high priority threshold not used */ - break; - case SK_TX_RAM_Q: - /* - * Do NOT use Store & Forward under normal operation due to - * performance optimization (GENESIS only). - * But if Jumbo Frames are configured (XMAC Tx FIFO is only 4 kB) - * or YUKON is used ((GMAC Tx FIFO is only 1 kB) - * we NEED Store & Forward of the RAM buffer. - */ - if (pAC->GIni.GIPortUsage == SK_JUMBO_LINK || - pAC->GIni.GIYukon) { - /* enable Store & Forward Mode for the Tx Side */ - SK_OUT8(IoC, RB_ADDR(QuIoOffs, RB_CTRL), RB_ENA_STFWD); - } - break; - } - - /* set queue operational */ - SK_OUT8(IoC, RB_ADDR(QuIoOffs, RB_CTRL), RB_ENA_OP_MD); - } - else { - /* ensure the queue is still disabled */ - SK_OUT8(IoC, RB_ADDR(QuIoOffs, RB_CTRL), RB_RST_SET); - } -} /* DoInitRamQueue */ - - -/****************************************************************************** - * - * SkGeInitRamBufs() - Initialize the RAM Buffer Queues - * - * Description: - * Initialize all RAM Buffer Queues of the specified port - * - * Returns: - * nothing - */ -static void SkGeInitRamBufs( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - int RxQType; - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PRxQSize == SK_MIN_RXQ_SIZE) { - RxQType = SK_RX_SRAM_Q; /* small Rx Queue */ - } - else { - RxQType = SK_RX_BRAM_Q; /* big Rx Queue */ - } - - DoInitRamQueue(pAC, IoC, pPrt->PRxQOff, pPrt->PRxQRamStart, - pPrt->PRxQRamEnd, RxQType); - - DoInitRamQueue(pAC, IoC, pPrt->PXsQOff, pPrt->PXsQRamStart, - pPrt->PXsQRamEnd, SK_TX_RAM_Q); - - DoInitRamQueue(pAC, IoC, pPrt->PXaQOff, pPrt->PXaQRamStart, - pPrt->PXaQRamEnd, SK_TX_RAM_Q); - -} /* SkGeInitRamBufs */ - - -/****************************************************************************** - * - * SkGeInitRamIface() - Initialize the RAM Interface - * - * Description: - * This function initializes the Adapters RAM Interface. - * - * Note: - * This function is used in the diagnostics. - * - * Returns: - * nothing - */ -static void SkGeInitRamIface( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC) /* IO context */ -{ - /* release local reset */ - SK_OUT16(IoC, B3_RI_CTRL, RI_RST_CLR); - - /* configure timeout values */ - SK_OUT8(IoC, B3_RI_WTO_R1, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_WTO_XA1, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_WTO_XS1, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_RTO_R1, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_RTO_XA1, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_RTO_XS1, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_WTO_R2, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_WTO_XA2, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_WTO_XS2, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_RTO_R2, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_RTO_XA2, SK_RI_TO_53); - SK_OUT8(IoC, B3_RI_RTO_XS2, SK_RI_TO_53); - -} /* SkGeInitRamIface */ - - -/****************************************************************************** - * - * SkGeInitBmu() - Initialize the BMU state machines - * - * Description: - * Initialize all BMU state machines of the specified port - * - * Returns: - * nothing - */ -static void SkGeInitBmu( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U32 RxWm; - SK_U32 TxWm; - - pPrt = &pAC->GIni.GP[Port]; - - RxWm = SK_BMU_RX_WM; - TxWm = SK_BMU_TX_WM; - - if (!pAC->GIni.GIPciSlot64 && !pAC->GIni.GIPciClock66) { - /* for better performance */ - RxWm /= 2; - TxWm /= 2; - } - - /* Rx Queue: Release all local resets and set the watermark */ - SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_CSR), CSR_CLR_RESET); - SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_F), RxWm); - - /* - * Tx Queue: Release all local resets if the queue is used ! - * set watermark - */ - if (pPrt->PXSQSize != 0) { - SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), CSR_CLR_RESET); - SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_F), TxWm); - } - - if (pPrt->PXAQSize != 0) { - SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), CSR_CLR_RESET); - SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_F), TxWm); - } - /* - * Do NOT enable the descriptor poll timers here, because - * the descriptor addresses are not specified yet. - */ -} /* SkGeInitBmu */ - - -/****************************************************************************** - * - * TestStopBit() - Test the stop bit of the queue - * - * Description: - * Stopping a queue is not as simple as it seems to be. - * If descriptor polling is enabled, it may happen - * that RX/TX stop is done and SV idle is NOT set. - * In this case we have to issue another stop command. - * - * Returns: - * The queues control status register - */ -static SK_U32 TestStopBit( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO Context */ -int QuIoOffs) /* Queue IO Address Offset */ -{ - SK_U32 QuCsr; /* CSR contents */ - - SK_IN32(IoC, Q_ADDR(QuIoOffs, Q_CSR), &QuCsr); - - if ((QuCsr & (CSR_STOP | CSR_SV_IDLE)) == 0) { - /* Stop Descriptor overridden by start command */ - SK_OUT32(IoC, Q_ADDR(QuIoOffs, Q_CSR), CSR_STOP); - - SK_IN32(IoC, Q_ADDR(QuIoOffs, Q_CSR), &QuCsr); - } - - return(QuCsr); -} /* TestStopBit */ - - -/****************************************************************************** - * - * SkGeStopPort() - Stop the Rx/Tx activity of the port 'Port'. - * - * Description: - * After calling this function the descriptor rings and Rx and Tx - * queues of this port may be reconfigured. - * - * It is possible to stop the receive and transmit path separate or - * both together. - * - * Dir = SK_STOP_TX Stops the transmit path only and resets the MAC. - * The receive queue is still active and - * the pending Rx frames may be still transferred - * into the RxD. - * SK_STOP_RX Stop the receive path. The tansmit path - * has to be stopped once before. - * SK_STOP_ALL SK_STOP_TX + SK_STOP_RX - * - * RstMode = SK_SOFT_RST Resets the MAC. The PHY is still alive. - * SK_HARD_RST Resets the MAC and the PHY. - * - * Example: - * 1) A Link Down event was signaled for a port. Therefore the activity - * of this port should be stopped and a hardware reset should be issued - * to enable the workaround of XMAC Errata #2. But the received frames - * should not be discarded. - * ... - * SkGeStopPort(pAC, IoC, Port, SK_STOP_TX, SK_HARD_RST); - * (transfer all pending Rx frames) - * SkGeStopPort(pAC, IoC, Port, SK_STOP_RX, SK_HARD_RST); - * ... - * - * 2) An event was issued which request the driver to switch - * the 'virtual active' link to an other already active port - * as soon as possible. The frames in the receive queue of this - * port may be lost. But the PHY must not be reset during this - * event. - * ... - * SkGeStopPort(pAC, IoC, Port, SK_STOP_ALL, SK_SOFT_RST); - * ... - * - * Extended Description: - * If SK_STOP_TX is set, - * o disable the MAC's receive and transmitter to prevent - * from sending incomplete frames - * o stop the port's transmit queues before terminating the - * BMUs to prevent from performing incomplete PCI cycles - * on the PCI bus - * - The network Rx and Tx activity and PCI Tx transfer is - * disabled now. - * o reset the MAC depending on the RstMode - * o Stop Interval Timer and Limit Counter of Tx Arbiter, - * also disable Force Sync bit and Enable Alloc bit. - * o perform a local reset of the port's Tx path - * - reset the PCI FIFO of the async Tx queue - * - reset the PCI FIFO of the sync Tx queue - * - reset the RAM Buffer async Tx queue - * - reset the RAM Buffer sync Tx queue - * - reset the MAC Tx FIFO - * o switch Link and Tx LED off, stop the LED counters - * - * If SK_STOP_RX is set, - * o stop the port's receive queue - * - The path data transfer activity is fully stopped now. - * o perform a local reset of the port's Rx path - * - reset the PCI FIFO of the Rx queue - * - reset the RAM Buffer receive queue - * - reset the MAC Rx FIFO - * o switch Rx LED off, stop the LED counter - * - * If all ports are stopped, - * o reset the RAM Interface. - * - * Notes: - * o This function may be called during the driver states RESET_PORT and - * SWITCH_PORT. - */ -void SkGeStopPort( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* I/O context */ -int Port, /* port to stop (MAC_1 + n) */ -int Dir, /* Direction to Stop (SK_STOP_RX, SK_STOP_TX, SK_STOP_ALL) */ -int RstMode)/* Reset Mode (SK_SOFT_RST, SK_HARD_RST) */ -{ -#ifndef SK_DIAG - SK_EVPARA Para; -#endif /* !SK_DIAG */ - SK_GEPORT *pPrt; - SK_U32 DWord; - SK_U32 XsCsr; - SK_U32 XaCsr; - SK_U64 ToutStart; - int i; - int ToutCnt; - - pPrt = &pAC->GIni.GP[Port]; - - if ((Dir & SK_STOP_TX) != 0) { - /* disable receiver and transmitter */ - SkMacRxTxDisable(pAC, IoC, Port); - - /* stop both transmit queues */ - /* - * If the BMU is in the reset state CSR_STOP will terminate - * immediately. - */ - SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), CSR_STOP); - SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), CSR_STOP); - - ToutStart = SkOsGetTime(pAC); - ToutCnt = 0; - do { - /* - * Clear packet arbiter timeout to make sure - * this loop will terminate. - */ - SK_OUT16(IoC, B3_PA_CTRL, (SK_U16)((Port == MAC_1) ? - PA_CLR_TO_TX1 : PA_CLR_TO_TX2)); - - /* - * If the transfer stucks at the MAC the STOP command will not - * terminate if we don't flush the XMAC's transmit FIFO ! - */ - SkMacFlushTxFifo(pAC, IoC, Port); - - XsCsr = TestStopBit(pAC, IoC, pPrt->PXsQOff); - XaCsr = TestStopBit(pAC, IoC, pPrt->PXaQOff); - - if (SkOsGetTime(pAC) - ToutStart > (SK_TICKS_PER_SEC / 18)) { - /* - * Timeout of 1/18 second reached. - * This needs to be checked at 1/18 sec only. - */ - ToutCnt++; - if (ToutCnt > 1) { - /* Might be a problem when the driver event handler - * calls StopPort again. XXX. - */ - - /* Fatal Error, Loop aborted */ - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_HWI_E018, - SKERR_HWI_E018MSG); -#ifndef SK_DIAG - Para.Para64 = Port; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); -#endif /* !SK_DIAG */ - return; - } - /* - * Cache incoherency workaround: Assume a start command - * has been lost while sending the frame. - */ - ToutStart = SkOsGetTime(pAC); - - if ((XsCsr & CSR_STOP) != 0) { - SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), CSR_START); - } - if ((XaCsr & CSR_STOP) != 0) { - SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), CSR_START); - } - } - - /* - * Because of the ASIC problem report entry from 21.08.1998 it is - * required to wait until CSR_STOP is reset and CSR_SV_IDLE is set. - */ - } while ((XsCsr & (CSR_STOP | CSR_SV_IDLE)) != CSR_SV_IDLE || - (XaCsr & (CSR_STOP | CSR_SV_IDLE)) != CSR_SV_IDLE); - - /* Reset the MAC depending on the RstMode */ - if (RstMode == SK_SOFT_RST) { - SkMacSoftRst(pAC, IoC, Port); - } - else { - SkMacHardRst(pAC, IoC, Port); - } - - /* Disable Force Sync bit and Enable Alloc bit */ - SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), - TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC); - - /* Stop Interval Timer and Limit Counter of Tx Arbiter */ - SK_OUT32(IoC, MR_ADDR(Port, TXA_ITI_INI), 0L); - SK_OUT32(IoC, MR_ADDR(Port, TXA_LIM_INI), 0L); - - /* Perform a local reset of the port's Tx path */ - - /* Reset the PCI FIFO of the async Tx queue */ - SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), CSR_SET_RESET); - /* Reset the PCI FIFO of the sync Tx queue */ - SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), CSR_SET_RESET); - /* Reset the RAM Buffer async Tx queue */ - SK_OUT8(IoC, RB_ADDR(pPrt->PXaQOff, RB_CTRL), RB_RST_SET); - /* Reset the RAM Buffer sync Tx queue */ - SK_OUT8(IoC, RB_ADDR(pPrt->PXsQOff, RB_CTRL), RB_RST_SET); - - /* Reset Tx MAC FIFO */ -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* Note: MFF_RST_SET does NOT reset the XMAC ! */ - SK_OUT8(IoC, MR_ADDR(Port, TX_MFF_CTRL2), MFF_RST_SET); - - /* switch Link and Tx LED off, stop the LED counters */ - /* Link LED is switched off by the RLMT and the Diag itself */ - SkGeXmitLED(pAC, IoC, MR_ADDR(Port, TX_LED_INI), SK_LED_DIS); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* Reset TX MAC FIFO */ - SK_OUT8(IoC, MR_ADDR(Port, TX_GMF_CTRL_T), (SK_U8)GMF_RST_SET); - } -#endif /* YUKON */ - } - - if ((Dir & SK_STOP_RX) != 0) { - /* - * The RX Stop Command will not terminate if no buffers - * are queued in the RxD ring. But it will always reach - * the Idle state. Therefore we can use this feature to - * stop the transfer of received packets. - */ - /* stop the port's receive queue */ - SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_CSR), CSR_STOP); - - i = 100; - do { - /* - * Clear packet arbiter timeout to make sure - * this loop will terminate - */ - SK_OUT16(IoC, B3_PA_CTRL, (SK_U16)((Port == MAC_1) ? - PA_CLR_TO_RX1 : PA_CLR_TO_RX2)); - - DWord = TestStopBit(pAC, IoC, pPrt->PRxQOff); - - /* timeout if i==0 (bug fix for #10748) */ - if (--i == 0) { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_HWI_E024, - SKERR_HWI_E024MSG); - break; - } - /* - * because of the ASIC problem report entry from 21.08.98 - * it is required to wait until CSR_STOP is reset and - * CSR_SV_IDLE is set. - */ - } while ((DWord & (CSR_STOP | CSR_SV_IDLE)) != CSR_SV_IDLE); - - /* The path data transfer activity is fully stopped now */ - - /* Perform a local reset of the port's Rx path */ - - /* Reset the PCI FIFO of the Rx queue */ - SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_CSR), CSR_SET_RESET); - /* Reset the RAM Buffer receive queue */ - SK_OUT8(IoC, RB_ADDR(pPrt->PRxQOff, RB_CTRL), RB_RST_SET); - - /* Reset Rx MAC FIFO */ -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - SK_OUT8(IoC, MR_ADDR(Port, RX_MFF_CTRL2), MFF_RST_SET); - - /* switch Rx LED off, stop the LED counter */ - SkGeXmitLED(pAC, IoC, MR_ADDR(Port, RX_LED_INI), SK_LED_DIS); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* Reset Rx MAC FIFO */ - SK_OUT8(IoC, MR_ADDR(Port, RX_GMF_CTRL_T), (SK_U8)GMF_RST_SET); - } -#endif /* YUKON */ - } -} /* SkGeStopPort */ - - -/****************************************************************************** - * - * SkGeInit0() - Level 0 Initialization - * - * Description: - * - Initialize the BMU address offsets - * - * Returns: - * nothing - */ -static void SkGeInit0( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC) /* IO context */ -{ - int i; - SK_GEPORT *pPrt; - - for (i = 0; i < SK_MAX_MACS; i++) { - pPrt = &pAC->GIni.GP[i]; - - pPrt->PState = SK_PRT_RESET; - pPrt->PRxQOff = QOffTab[i].RxQOff; - pPrt->PXsQOff = QOffTab[i].XsQOff; - pPrt->PXaQOff = QOffTab[i].XaQOff; - pPrt->PCheckPar = SK_FALSE; - pPrt->PIsave = 0; - pPrt->PPrevShorts = 0; - pPrt->PLinkResCt = 0; - pPrt->PAutoNegTOCt = 0; - pPrt->PPrevRx = 0; - pPrt->PPrevFcs = 0; - pPrt->PRxLim = SK_DEF_RX_WA_LIM; - pPrt->PLinkMode = (SK_U8)SK_LMODE_AUTOFULL; - pPrt->PLinkSpeedCap = (SK_U8)SK_LSPEED_CAP_1000MBPS; - pPrt->PLinkSpeed = (SK_U8)SK_LSPEED_1000MBPS; - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_UNKNOWN; - pPrt->PLinkModeConf = (SK_U8)SK_LMODE_AUTOSENSE; - pPrt->PFlowCtrlMode = (SK_U8)SK_FLOW_MODE_SYM_OR_REM; - pPrt->PLinkCap = (SK_U8)(SK_LMODE_CAP_HALF | SK_LMODE_CAP_FULL | - SK_LMODE_CAP_AUTOHALF | SK_LMODE_CAP_AUTOFULL); - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_UNKNOWN; - pPrt->PFlowCtrlCap = (SK_U8)SK_FLOW_MODE_SYM_OR_REM; - pPrt->PFlowCtrlStatus = (SK_U8)SK_FLOW_STAT_NONE; - pPrt->PMSCap = 0; - pPrt->PMSMode = (SK_U8)SK_MS_MODE_AUTO; - pPrt->PMSStatus = (SK_U8)SK_MS_STAT_UNSET; - pPrt->PLipaAutoNeg = (SK_U8)SK_LIPA_UNKNOWN; - pPrt->PAutoNegFail = SK_FALSE; - pPrt->PHWLinkUp = SK_FALSE; - pPrt->PLinkBroken = SK_TRUE; /* See WA code */ - pPrt->PPhyPowerState = PHY_PM_OPERATIONAL_MODE; - pPrt->PMacColThres = TX_COL_DEF; - pPrt->PMacJamLen = TX_JAM_LEN_DEF; - pPrt->PMacJamIpgVal = TX_JAM_IPG_DEF; - pPrt->PMacJamIpgData = TX_IPG_JAM_DEF; - pPrt->PMacIpgData = IPG_DATA_DEF; - pPrt->PMacLimit4 = SK_FALSE; - } - - pAC->GIni.GIPortUsage = SK_RED_LINK; - pAC->GIni.GILedBlinkCtrl = (SK_U16)OemConfig.Value; - pAC->GIni.GIValIrqMask = IS_ALL_MSK; - -} /* SkGeInit0*/ - - -/****************************************************************************** - * - * SkGeInit1() - Level 1 Initialization - * - * Description: - * o Do a software reset. - * o Clear all reset bits. - * o Verify that the detected hardware is present. - * Return an error if not. - * o Get the hardware configuration - * + Read the number of MACs/Ports. - * + Read the RAM size. - * + Read the PCI Revision Id. - * + Find out the adapters host clock speed - * + Read and check the PHY type - * - * Returns: - * 0: success - * 5: Unexpected PHY type detected - * 6: HW self test failed - */ -static int SkGeInit1( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC) /* IO context */ -{ - SK_U8 Byte; - SK_U16 Word; - SK_U16 CtrlStat; - SK_U32 DWord; - int RetVal; - int i; - - RetVal = 0; - - /* save CLK_RUN bits (YUKON-Lite) */ - SK_IN16(IoC, B0_CTST, &CtrlStat); - - /* do the SW-reset */ - SK_OUT8(IoC, B0_CTST, CS_RST_SET); - - /* release the SW-reset */ - SK_OUT8(IoC, B0_CTST, CS_RST_CLR); - - /* reset all error bits in the PCI STATUS register */ - /* - * Note: PCI Cfg cycles cannot be used, because they are not - * available on some platforms after 'boot time'. - */ - SK_IN16(IoC, PCI_C(PCI_STATUS), &Word); - - SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_ON); - SK_OUT16(IoC, PCI_C(PCI_STATUS), (SK_U16)(Word | PCI_ERRBITS)); - SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_OFF); - - /* release Master Reset */ - SK_OUT8(IoC, B0_CTST, CS_MRST_CLR); - -#ifdef CLK_RUN - CtrlStat |= CS_CLK_RUN_ENA; -#endif /* CLK_RUN */ - - /* restore CLK_RUN bits */ - SK_OUT16(IoC, B0_CTST, (SK_U16)(CtrlStat & - (CS_CLK_RUN_HOT | CS_CLK_RUN_RST | CS_CLK_RUN_ENA))); - - /* read Chip Identification Number */ - SK_IN8(IoC, B2_CHIP_ID, &Byte); - pAC->GIni.GIChipId = Byte; - - /* read number of MACs */ - SK_IN8(IoC, B2_MAC_CFG, &Byte); - pAC->GIni.GIMacsFound = (Byte & CFG_SNG_MAC) ? 1 : 2; - - /* get Chip Revision Number */ - pAC->GIni.GIChipRev = (SK_U8)((Byte & CFG_CHIP_R_MSK) >> 4); - - /* get diff. PCI parameters */ - SK_IN16(IoC, B0_CTST, &CtrlStat); - - /* read the adapters RAM size */ - SK_IN8(IoC, B2_E_0, &Byte); - - pAC->GIni.GIGenesis = SK_FALSE; - pAC->GIni.GIYukon = SK_FALSE; - pAC->GIni.GIYukonLite = SK_FALSE; - -#ifdef GENESIS - if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) { - - pAC->GIni.GIGenesis = SK_TRUE; - - if (Byte == (SK_U8)3) { - /* special case: 4 x 64k x 36, offset = 0x80000 */ - pAC->GIni.GIRamSize = 1024; - pAC->GIni.GIRamOffs = (SK_U32)512 * 1024; - } - else { - pAC->GIni.GIRamSize = (int)Byte * 512; - pAC->GIni.GIRamOffs = 0; - } - /* all GE adapters work with 53.125 MHz host clock */ - pAC->GIni.GIHstClkFact = SK_FACT_53; - - /* set Descr. Poll Timer Init Value to 250 ms */ - pAC->GIni.GIPollTimerVal = - SK_DPOLL_DEF * (SK_U32)pAC->GIni.GIHstClkFact / 100; - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIChipId != CHIP_ID_GENESIS) { - - pAC->GIni.GIYukon = SK_TRUE; - - pAC->GIni.GIRamSize = (Byte == (SK_U8)0) ? 128 : (int)Byte * 4; - - pAC->GIni.GIRamOffs = 0; - - /* WA for chip Rev. A */ - pAC->GIni.GIWolOffs = (pAC->GIni.GIChipId == CHIP_ID_YUKON && - pAC->GIni.GIChipRev == 0) ? WOL_REG_OFFS : 0; - - /* get PM Capabilities of PCI config space */ - SK_IN16(IoC, PCI_C(PCI_PM_CAP_REG), &Word); - - /* check if VAUX is available */ - if (((CtrlStat & CS_VAUX_AVAIL) != 0) && - /* check also if PME from D3cold is set */ - ((Word & PCI_PME_D3C_SUP) != 0)) { - /* set entry in GE init struct */ - pAC->GIni.GIVauxAvail = SK_TRUE; - } - - if (pAC->GIni.GIChipId == CHIP_ID_YUKON_LITE) { - /* this is Rev. A1 */ - pAC->GIni.GIYukonLite = SK_TRUE; - } - else { - /* save Flash-Address Register */ - SK_IN32(IoC, B2_FAR, &DWord); - - /* test Flash-Address Register */ - SK_OUT8(IoC, B2_FAR + 3, 0xff); - SK_IN8(IoC, B2_FAR + 3, &Byte); - - if (Byte != 0) { - /* this is Rev. A0 */ - pAC->GIni.GIYukonLite = SK_TRUE; - - /* restore Flash-Address Register */ - SK_OUT32(IoC, B2_FAR, DWord); - } - } - - /* switch power to VCC (WA for VAUX problem) */ - SK_OUT8(IoC, B0_POWER_CTRL, (SK_U8)(PC_VAUX_ENA | PC_VCC_ENA | - PC_VAUX_OFF | PC_VCC_ON)); - - /* read the Interrupt source */ - SK_IN32(IoC, B0_ISRC, &DWord); - - if ((DWord & IS_HW_ERR) != 0) { - /* read the HW Error Interrupt source */ - SK_IN32(IoC, B0_HWE_ISRC, &DWord); - - if ((DWord & IS_IRQ_SENSOR) != 0) { - /* disable HW Error IRQ */ - pAC->GIni.GIValIrqMask &= ~IS_HW_ERR; - } - } - - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - /* set GMAC Link Control reset */ - SK_OUT16(IoC, MR_ADDR(i, GMAC_LINK_CTRL), GMLC_RST_SET); - - /* clear GMAC Link Control reset */ - SK_OUT16(IoC, MR_ADDR(i, GMAC_LINK_CTRL), GMLC_RST_CLR); - } - /* all YU chips work with 78.125 MHz host clock */ - pAC->GIni.GIHstClkFact = SK_FACT_78; - - pAC->GIni.GIPollTimerVal = SK_DPOLL_MAX; /* 215 ms */ - } -#endif /* YUKON */ - - /* check if 64-bit PCI Slot is present */ - pAC->GIni.GIPciSlot64 = (SK_BOOL)((CtrlStat & CS_BUS_SLOT_SZ) != 0); - - /* check if 66 MHz PCI Clock is active */ - pAC->GIni.GIPciClock66 = (SK_BOOL)((CtrlStat & CS_BUS_CLOCK) != 0); - - /* read PCI HW Revision Id. */ - SK_IN8(IoC, PCI_C(PCI_REV_ID), &Byte); - pAC->GIni.GIPciHwRev = Byte; - - /* read the PMD type */ - SK_IN8(IoC, B2_PMD_TYP, &Byte); - pAC->GIni.GICopperType = (SK_U8)(Byte == 'T'); - - /* read the PHY type */ - SK_IN8(IoC, B2_E_1, &Byte); - - Byte &= 0x0f; /* the PHY type is stored in the lower nibble */ - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - switch (Byte) { - case SK_PHY_XMAC: - pAC->GIni.GP[i].PhyAddr = PHY_ADDR_XMAC; - break; - case SK_PHY_BCOM: - pAC->GIni.GP[i].PhyAddr = PHY_ADDR_BCOM; - pAC->GIni.GP[i].PMSCap = (SK_U8)(SK_MS_CAP_AUTO | - SK_MS_CAP_MASTER | SK_MS_CAP_SLAVE); - break; -#ifdef OTHER_PHY - case SK_PHY_LONE: - pAC->GIni.GP[i].PhyAddr = PHY_ADDR_LONE; - break; - case SK_PHY_NAT: - pAC->GIni.GP[i].PhyAddr = PHY_ADDR_NAT; - break; -#endif /* OTHER_PHY */ - default: - /* ERROR: unexpected PHY type detected */ - RetVal = 5; - break; - } - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - if (Byte < (SK_U8)SK_PHY_MARV_COPPER) { - /* if this field is not initialized */ - Byte = (SK_U8)SK_PHY_MARV_COPPER; - - pAC->GIni.GICopperType = SK_TRUE; - } - - pAC->GIni.GP[i].PhyAddr = PHY_ADDR_MARV; - - if (pAC->GIni.GICopperType) { - - pAC->GIni.GP[i].PLinkSpeedCap = (SK_U8)(SK_LSPEED_CAP_AUTO | - SK_LSPEED_CAP_10MBPS | SK_LSPEED_CAP_100MBPS | - SK_LSPEED_CAP_1000MBPS); - - pAC->GIni.GP[i].PLinkSpeed = (SK_U8)SK_LSPEED_AUTO; - - pAC->GIni.GP[i].PMSCap = (SK_U8)(SK_MS_CAP_AUTO | - SK_MS_CAP_MASTER | SK_MS_CAP_SLAVE); - } - else { - Byte = (SK_U8)SK_PHY_MARV_FIBER; - } - } -#endif /* YUKON */ - - pAC->GIni.GP[i].PhyType = (int)Byte; - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_INIT, - ("PHY type: %d PHY addr: %04x\n", Byte, - pAC->GIni.GP[i].PhyAddr)); - } - - /* get MAC Type & set function pointers dependent on */ -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - pAC->GIni.GIMacType = SK_MAC_XMAC; - - pAC->GIni.GIFunc.pFnMacUpdateStats = SkXmUpdateStats; - pAC->GIni.GIFunc.pFnMacStatistic = SkXmMacStatistic; - pAC->GIni.GIFunc.pFnMacResetCounter = SkXmResetCounter; - pAC->GIni.GIFunc.pFnMacOverflow = SkXmOverflowStatus; - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - pAC->GIni.GIMacType = SK_MAC_GMAC; - - pAC->GIni.GIFunc.pFnMacUpdateStats = SkGmUpdateStats; - pAC->GIni.GIFunc.pFnMacStatistic = SkGmMacStatistic; - pAC->GIni.GIFunc.pFnMacResetCounter = SkGmResetCounter; - pAC->GIni.GIFunc.pFnMacOverflow = SkGmOverflowStatus; - -#ifdef SPECIAL_HANDLING - if (pAC->GIni.GIChipId == CHIP_ID_YUKON) { - /* check HW self test result */ - SK_IN8(IoC, B2_E_3, &Byte); - if (Byte & B2_E3_RES_MASK) { - RetVal = 6; - } - } -#endif - } -#endif /* YUKON */ - - return(RetVal); -} /* SkGeInit1 */ - - -/****************************************************************************** - * - * SkGeInit2() - Level 2 Initialization - * - * Description: - * - start the Blink Source Counter - * - start the Descriptor Poll Timer - * - configure the MAC-Arbiter - * - configure the Packet-Arbiter - * - enable the Tx Arbiters - * - enable the RAM Interface Arbiter - * - * Returns: - * nothing - */ -static void SkGeInit2( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC) /* IO context */ -{ -#ifdef GENESIS - SK_U32 DWord; -#endif /* GENESIS */ - int i; - - /* start the Descriptor Poll Timer */ - if (pAC->GIni.GIPollTimerVal != 0) { - if (pAC->GIni.GIPollTimerVal > SK_DPOLL_MAX) { - pAC->GIni.GIPollTimerVal = SK_DPOLL_MAX; - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E017, SKERR_HWI_E017MSG); - } - SK_OUT32(IoC, B28_DPT_INI, pAC->GIni.GIPollTimerVal); - SK_OUT8(IoC, B28_DPT_CTRL, DPT_START); - } - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* start the Blink Source Counter */ - DWord = SK_BLK_DUR * (SK_U32)pAC->GIni.GIHstClkFact / 100; - - SK_OUT32(IoC, B2_BSC_INI, DWord); - SK_OUT8(IoC, B2_BSC_CTRL, BSC_START); - - /* - * Configure the MAC Arbiter and the Packet Arbiter. - * They will be started once and never be stopped. - */ - SkGeInitMacArb(pAC, IoC); - - SkGeInitPktArb(pAC, IoC); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* start Time Stamp Timer */ - SK_OUT8(IoC, GMAC_TI_ST_CTRL, (SK_U8)GMT_ST_START); - } -#endif /* YUKON */ - - /* enable the Tx Arbiters */ - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - SK_OUT8(IoC, MR_ADDR(i, TXA_CTRL), TXA_ENA_ARB); - } - - /* enable the RAM Interface Arbiter */ - SkGeInitRamIface(pAC, IoC); - -} /* SkGeInit2 */ - -/****************************************************************************** - * - * SkGeInit() - Initialize the GE Adapter with the specified level. - * - * Description: - * Level 0: Initialize the Module structures. - * Level 1: Generic Hardware Initialization. The IOP/MemBase pointer has - * to be set before calling this level. - * - * o Do a software reset. - * o Clear all reset bits. - * o Verify that the detected hardware is present. - * Return an error if not. - * o Get the hardware configuration - * + Set GIMacsFound with the number of MACs. - * + Store the RAM size in GIRamSize. - * + Save the PCI Revision ID in GIPciHwRev. - * o return an error - * if Number of MACs > SK_MAX_MACS - * - * After returning from Level 0 the adapter - * may be accessed with IO operations. - * - * Level 2: start the Blink Source Counter - * - * Returns: - * 0: success - * 1: Number of MACs exceeds SK_MAX_MACS (after level 1) - * 2: Adapter not present or not accessible - * 3: Illegal initialization level - * 4: Initialization Level 1 Call missing - * 5: Unexpected PHY type detected - * 6: HW self test failed - */ -int SkGeInit( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Level) /* initialization level */ -{ - int RetVal; /* return value */ - SK_U32 DWord; - - RetVal = 0; - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_INIT, - ("SkGeInit(Level %d)\n", Level)); - - switch (Level) { - case SK_INIT_DATA: - /* Initialization Level 0 */ - SkGeInit0(pAC, IoC); - pAC->GIni.GILevel = SK_INIT_DATA; - break; - - case SK_INIT_IO: - /* Initialization Level 1 */ - RetVal = SkGeInit1(pAC, IoC); - if (RetVal != 0) { - break; - } - - /* check if the adapter seems to be accessible */ - SK_OUT32(IoC, B2_IRQM_INI, SK_TEST_VAL); - SK_IN32(IoC, B2_IRQM_INI, &DWord); - SK_OUT32(IoC, B2_IRQM_INI, 0L); - - if (DWord != SK_TEST_VAL) { - RetVal = 2; - break; - } - - /* check if the number of GIMacsFound matches SK_MAX_MACS */ - if (pAC->GIni.GIMacsFound > SK_MAX_MACS) { - RetVal = 1; - break; - } - - /* Level 1 successfully passed */ - pAC->GIni.GILevel = SK_INIT_IO; - break; - - case SK_INIT_RUN: - /* Initialization Level 2 */ - if (pAC->GIni.GILevel != SK_INIT_IO) { -#ifndef SK_DIAG - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E002, SKERR_HWI_E002MSG); -#endif /* !SK_DIAG */ - RetVal = 4; - break; - } - SkGeInit2(pAC, IoC); - - /* Level 2 successfully passed */ - pAC->GIni.GILevel = SK_INIT_RUN; - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E003, SKERR_HWI_E003MSG); - RetVal = 3; - break; - } - - return(RetVal); -} /* SkGeInit */ - - -/****************************************************************************** - * - * SkGeDeInit() - Deinitialize the adapter - * - * Description: - * All ports of the adapter will be stopped if not already done. - * Do a software reset and switch off all LEDs. - * - * Returns: - * nothing - */ -void SkGeDeInit( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC) /* IO context */ -{ - int i; - SK_U16 Word; - -#if (!defined(SK_SLIM) && !defined(VCPU)) - /* ensure I2C is ready */ - SkI2cWaitIrq(pAC, IoC); -#endif - - /* stop all current transfer activity */ - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - if (pAC->GIni.GP[i].PState != SK_PRT_STOP && - pAC->GIni.GP[i].PState != SK_PRT_RESET) { - - SkGeStopPort(pAC, IoC, i, SK_STOP_ALL, SK_HARD_RST); - } - } - - /* Reset all bits in the PCI STATUS register */ - /* - * Note: PCI Cfg cycles cannot be used, because they are not - * available on some platforms after 'boot time'. - */ - SK_IN16(IoC, PCI_C(PCI_STATUS), &Word); - - SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_ON); - SK_OUT16(IoC, PCI_C(PCI_STATUS), (SK_U16)(Word | PCI_ERRBITS)); - SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_OFF); - - /* do the reset, all LEDs are switched off now */ - SK_OUT8(IoC, B0_CTST, CS_RST_SET); - - pAC->GIni.GILevel = SK_INIT_DATA; -} /* SkGeDeInit */ - - -/****************************************************************************** - * - * SkGeInitPort() Initialize the specified port. - * - * Description: - * PRxQSize, PXSQSize, and PXAQSize has to be - * configured for the specified port before calling this function. - * The descriptor rings has to be initialized too. - * - * o (Re)configure queues of the specified port. - * o configure the MAC of the specified port. - * o put ASIC and MAC(s) in operational mode. - * o initialize Rx/Tx and Sync LED - * o initialize RAM Buffers and MAC FIFOs - * - * The port is ready to connect when returning. - * - * Note: - * The MAC's Rx and Tx state machine is still disabled when returning. - * - * Returns: - * 0: success - * 1: Queue size initialization error. The configured values - * for PRxQSize, PXSQSize, or PXAQSize are invalid for one - * or more queues. The specified port was NOT initialized. - * An error log entry was generated. - * 2: The port has to be stopped before it can be initialized again. - */ -int SkGeInitPort( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port to configure */ -{ - SK_GEPORT *pPrt; - - pPrt = &pAC->GIni.GP[Port]; - - if (SkGeCheckQSize(pAC, Port) != 0) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E004, SKERR_HWI_E004MSG); - return(1); - } - - if (pPrt->PState == SK_PRT_INIT || pPrt->PState == SK_PRT_RUN) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E005, SKERR_HWI_E005MSG); - return(2); - } - - /* configuration ok, initialize the Port now */ - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* initialize Rx, Tx and Link LED */ - /* - * If 1000BT Phy needs LED initialization than swap - * LED and XMAC initialization order - */ - SkGeXmitLED(pAC, IoC, MR_ADDR(Port, TX_LED_INI), SK_LED_ENA); - SkGeXmitLED(pAC, IoC, MR_ADDR(Port, RX_LED_INI), SK_LED_ENA); - /* The Link LED is initialized by RLMT or Diagnostics itself */ - - SkXmInitMac(pAC, IoC, Port); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - SkGmInitMac(pAC, IoC, Port); - } -#endif /* YUKON */ - - /* do NOT initialize the Link Sync Counter */ - - SkGeInitMacFifo(pAC, IoC, Port); - - SkGeInitRamBufs(pAC, IoC, Port); - - if (pPrt->PXSQSize != 0) { - /* enable Force Sync bit if synchronous queue available */ - SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), TXA_ENA_FSYNC); - } - - SkGeInitBmu(pAC, IoC, Port); - - /* mark port as initialized */ - pPrt->PState = SK_PRT_INIT; - - return(0); -} /* SkGeInitPort */ diff --git a/drivers/net/sk98lin/skgemib.c b/drivers/net/sk98lin/skgemib.c deleted file mode 100644 index 0a6f67a7a395..000000000000 --- a/drivers/net/sk98lin/skgemib.c +++ /dev/null @@ -1,1075 +0,0 @@ -/***************************************************************************** - * - * Name: skgemib.c - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.11 $ - * Date: $Date: 2003/09/15 13:38:12 $ - * Purpose: Private Network Management Interface Management Database - * - ****************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * PRIVATE OID handler function prototypes - */ -PNMI_STATIC int Addr(SK_AC *pAC, SK_IOC IoC, int action, - SK_U32 Id, char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int CsumStat(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int General(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int Mac8023Stat(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int MacPrivateConf(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int MacPrivateStat(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int Monitor(SK_AC *pAC, SK_IOC IoC, int action, - SK_U32 Id, char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int OidStruct(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int Perform(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int* pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int Rlmt(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int RlmtStat(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int SensorStat(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int Vpd(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC int Vct(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); - -#ifdef SK_POWER_MGMT -PNMI_STATIC int PowerManagement(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -#endif /* SK_POWER_MGMT */ - -#ifdef SK_DIAG_SUPPORT -PNMI_STATIC int DiagActions(SK_AC *pAC, SK_IOC IoC, int action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, - unsigned int TableIndex, SK_U32 NetIndex); -#endif /* SK_DIAG_SUPPORT */ - - -/* defines *******************************************************************/ -#define ID_TABLE_SIZE (sizeof(IdTable)/sizeof(IdTable[0])) - - -/* global variables **********************************************************/ - -/* - * Table to correlate OID with handler function and index to - * hardware register stored in StatAddress if applicable. - */ -PNMI_STATIC const SK_PNMI_TAB_ENTRY IdTable[] = { - {OID_GEN_XMIT_OK, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX}, - {OID_GEN_RCV_OK, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HRX}, - {OID_GEN_XMIT_ERROR, - 0, - 0, - 0, - SK_PNMI_RO, General, 0}, - {OID_GEN_RCV_ERROR, - 0, - 0, - 0, - SK_PNMI_RO, General, 0}, - {OID_GEN_RCV_NO_BUFFER, - 0, - 0, - 0, - SK_PNMI_RO, General, 0}, - {OID_GEN_DIRECTED_FRAMES_XMIT, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_UNICAST}, - {OID_GEN_MULTICAST_FRAMES_XMIT, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_MULTICAST}, - {OID_GEN_BROADCAST_FRAMES_XMIT, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_BROADCAST}, - {OID_GEN_DIRECTED_FRAMES_RCV, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HRX_UNICAST}, - {OID_GEN_MULTICAST_FRAMES_RCV, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HRX_MULTICAST}, - {OID_GEN_BROADCAST_FRAMES_RCV, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HRX_BROADCAST}, - {OID_GEN_RCV_CRC_ERROR, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HRX_FCS}, - {OID_GEN_TRANSMIT_QUEUE_LENGTH, - 0, - 0, - 0, - SK_PNMI_RO, General, 0}, - {OID_802_3_PERMANENT_ADDRESS, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, 0}, - {OID_802_3_CURRENT_ADDRESS, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, 0}, - {OID_802_3_RCV_ERROR_ALIGNMENT, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HRX_FRAMING}, - {OID_802_3_XMIT_ONE_COLLISION, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_SINGLE_COL}, - {OID_802_3_XMIT_MORE_COLLISIONS, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_MULTI_COL}, - {OID_802_3_XMIT_DEFERRED, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_DEFFERAL}, - {OID_802_3_XMIT_MAX_COLLISIONS, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_EXCESS_COL}, - {OID_802_3_RCV_OVERRUN, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HRX_OVERFLOW}, - {OID_802_3_XMIT_UNDERRUN, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_UNDERRUN}, - {OID_802_3_XMIT_TIMES_CRS_LOST, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_CARRIER}, - {OID_802_3_XMIT_LATE_COLLISIONS, - 0, - 0, - 0, - SK_PNMI_RO, Mac8023Stat, SK_PNMI_HTX_LATE_COL}, -#ifdef SK_POWER_MGMT - {OID_PNP_CAPABILITIES, - 0, - 0, - 0, - SK_PNMI_RO, PowerManagement, 0}, - {OID_PNP_SET_POWER, - 0, - 0, - 0, - SK_PNMI_WO, PowerManagement, 0}, - {OID_PNP_QUERY_POWER, - 0, - 0, - 0, - SK_PNMI_RO, PowerManagement, 0}, - {OID_PNP_ADD_WAKE_UP_PATTERN, - 0, - 0, - 0, - SK_PNMI_WO, PowerManagement, 0}, - {OID_PNP_REMOVE_WAKE_UP_PATTERN, - 0, - 0, - 0, - SK_PNMI_WO, PowerManagement, 0}, - {OID_PNP_ENABLE_WAKE_UP, - 0, - 0, - 0, - SK_PNMI_RW, PowerManagement, 0}, -#endif /* SK_POWER_MGMT */ -#ifdef SK_DIAG_SUPPORT - {OID_SKGE_DIAG_MODE, - 0, - 0, - 0, - SK_PNMI_RW, DiagActions, 0}, -#endif /* SK_DIAG_SUPPORT */ - {OID_SKGE_MDB_VERSION, - 1, - 0, - SK_PNMI_MAI_OFF(MgmtDBVersion), - SK_PNMI_RO, General, 0}, - {OID_SKGE_SUPPORTED_LIST, - 0, - 0, - 0, - SK_PNMI_RO, General, 0}, - {OID_SKGE_ALL_DATA, - 0, - 0, - 0, - SK_PNMI_RW, OidStruct, 0}, - {OID_SKGE_VPD_FREE_BYTES, - 1, - 0, - SK_PNMI_MAI_OFF(VpdFreeBytes), - SK_PNMI_RO, Vpd, 0}, - {OID_SKGE_VPD_ENTRIES_LIST, - 1, - 0, - SK_PNMI_MAI_OFF(VpdEntriesList), - SK_PNMI_RO, Vpd, 0}, - {OID_SKGE_VPD_ENTRIES_NUMBER, - 1, - 0, - SK_PNMI_MAI_OFF(VpdEntriesNumber), - SK_PNMI_RO, Vpd, 0}, - {OID_SKGE_VPD_KEY, - SK_PNMI_VPD_ENTRIES, - sizeof(SK_PNMI_VPD), - SK_PNMI_OFF(Vpd) + SK_PNMI_VPD_OFF(VpdKey), - SK_PNMI_RO, Vpd, 0}, - {OID_SKGE_VPD_VALUE, - SK_PNMI_VPD_ENTRIES, - sizeof(SK_PNMI_VPD), - SK_PNMI_OFF(Vpd) + SK_PNMI_VPD_OFF(VpdValue), - SK_PNMI_RO, Vpd, 0}, - {OID_SKGE_VPD_ACCESS, - SK_PNMI_VPD_ENTRIES, - sizeof(SK_PNMI_VPD), - SK_PNMI_OFF(Vpd) + SK_PNMI_VPD_OFF(VpdAccess), - SK_PNMI_RO, Vpd, 0}, - {OID_SKGE_VPD_ACTION, - SK_PNMI_VPD_ENTRIES, - sizeof(SK_PNMI_VPD), - SK_PNMI_OFF(Vpd) + SK_PNMI_VPD_OFF(VpdAction), - SK_PNMI_RW, Vpd, 0}, - {OID_SKGE_PORT_NUMBER, - 1, - 0, - SK_PNMI_MAI_OFF(PortNumber), - SK_PNMI_RO, General, 0}, - {OID_SKGE_DEVICE_TYPE, - 1, - 0, - SK_PNMI_MAI_OFF(DeviceType), - SK_PNMI_RO, General, 0}, - {OID_SKGE_DRIVER_DESCR, - 1, - 0, - SK_PNMI_MAI_OFF(DriverDescr), - SK_PNMI_RO, General, 0}, - {OID_SKGE_DRIVER_VERSION, - 1, - 0, - SK_PNMI_MAI_OFF(DriverVersion), - SK_PNMI_RO, General, 0}, - {OID_SKGE_DRIVER_RELDATE, - 1, - 0, - SK_PNMI_MAI_OFF(DriverReleaseDate), - SK_PNMI_RO, General, 0}, - {OID_SKGE_DRIVER_FILENAME, - 1, - 0, - SK_PNMI_MAI_OFF(DriverFileName), - SK_PNMI_RO, General, 0}, - {OID_SKGE_HW_DESCR, - 1, - 0, - SK_PNMI_MAI_OFF(HwDescr), - SK_PNMI_RO, General, 0}, - {OID_SKGE_HW_VERSION, - 1, - 0, - SK_PNMI_MAI_OFF(HwVersion), - SK_PNMI_RO, General, 0}, - {OID_SKGE_CHIPSET, - 1, - 0, - SK_PNMI_MAI_OFF(Chipset), - SK_PNMI_RO, General, 0}, - {OID_SKGE_CHIPID, - 1, - 0, - SK_PNMI_MAI_OFF(ChipId), - SK_PNMI_RO, General, 0}, - {OID_SKGE_RAMSIZE, - 1, - 0, - SK_PNMI_MAI_OFF(RamSize), - SK_PNMI_RO, General, 0}, - {OID_SKGE_VAUXAVAIL, - 1, - 0, - SK_PNMI_MAI_OFF(VauxAvail), - SK_PNMI_RO, General, 0}, - {OID_SKGE_ACTION, - 1, - 0, - SK_PNMI_MAI_OFF(Action), - SK_PNMI_RW, Perform, 0}, - {OID_SKGE_RESULT, - 1, - 0, - SK_PNMI_MAI_OFF(TestResult), - SK_PNMI_RO, General, 0}, - {OID_SKGE_BUS_TYPE, - 1, - 0, - SK_PNMI_MAI_OFF(BusType), - SK_PNMI_RO, General, 0}, - {OID_SKGE_BUS_SPEED, - 1, - 0, - SK_PNMI_MAI_OFF(BusSpeed), - SK_PNMI_RO, General, 0}, - {OID_SKGE_BUS_WIDTH, - 1, - 0, - SK_PNMI_MAI_OFF(BusWidth), - SK_PNMI_RO, General, 0}, - {OID_SKGE_TX_SW_QUEUE_LEN, - 1, - 0, - SK_PNMI_MAI_OFF(TxSwQueueLen), - SK_PNMI_RO, General, 0}, - {OID_SKGE_TX_SW_QUEUE_MAX, - 1, - 0, - SK_PNMI_MAI_OFF(TxSwQueueMax), - SK_PNMI_RO, General, 0}, - {OID_SKGE_TX_RETRY, - 1, - 0, - SK_PNMI_MAI_OFF(TxRetryCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_RX_INTR_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(RxIntrCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_TX_INTR_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(TxIntrCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_RX_NO_BUF_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(RxNoBufCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_TX_NO_BUF_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(TxNoBufCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_TX_USED_DESCR_NO, - 1, - 0, - SK_PNMI_MAI_OFF(TxUsedDescrNo), - SK_PNMI_RO, General, 0}, - {OID_SKGE_RX_DELIVERED_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(RxDeliveredCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_RX_OCTETS_DELIV_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(RxOctetsDeliveredCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_RX_HW_ERROR_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(RxHwErrorsCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_TX_HW_ERROR_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(TxHwErrorsCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_IN_ERRORS_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(InErrorsCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_OUT_ERROR_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(OutErrorsCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_ERR_RECOVERY_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(ErrRecoveryCts), - SK_PNMI_RO, General, 0}, - {OID_SKGE_SYSUPTIME, - 1, - 0, - SK_PNMI_MAI_OFF(SysUpTime), - SK_PNMI_RO, General, 0}, - {OID_SKGE_SENSOR_NUMBER, - 1, - 0, - SK_PNMI_MAI_OFF(SensorNumber), - SK_PNMI_RO, General, 0}, - {OID_SKGE_SENSOR_INDEX, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorIndex), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_DESCR, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorDescr), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_TYPE, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorType), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_VALUE, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorValue), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_WAR_THRES_LOW, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorWarningThresholdLow), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_WAR_THRES_UPP, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorWarningThresholdHigh), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_ERR_THRES_LOW, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorErrorThresholdLow), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_ERR_THRES_UPP, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorErrorThresholdHigh), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_STATUS, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorStatus), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_WAR_CTS, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorWarningCts), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_ERR_CTS, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorErrorCts), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_WAR_TIME, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorWarningTimestamp), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_SENSOR_ERR_TIME, - SK_PNMI_SENSOR_ENTRIES, - sizeof(SK_PNMI_SENSOR), - SK_PNMI_OFF(Sensor) + SK_PNMI_SEN_OFF(SensorErrorTimestamp), - SK_PNMI_RO, SensorStat, 0}, - {OID_SKGE_CHKSM_NUMBER, - 1, - 0, - SK_PNMI_MAI_OFF(ChecksumNumber), - SK_PNMI_RO, General, 0}, - {OID_SKGE_CHKSM_RX_OK_CTS, - SKCS_NUM_PROTOCOLS, - sizeof(SK_PNMI_CHECKSUM), - SK_PNMI_OFF(Checksum) + SK_PNMI_CHK_OFF(ChecksumRxOkCts), - SK_PNMI_RO, CsumStat, 0}, - {OID_SKGE_CHKSM_RX_UNABLE_CTS, - SKCS_NUM_PROTOCOLS, - sizeof(SK_PNMI_CHECKSUM), - SK_PNMI_OFF(Checksum) + SK_PNMI_CHK_OFF(ChecksumRxUnableCts), - SK_PNMI_RO, CsumStat, 0}, - {OID_SKGE_CHKSM_RX_ERR_CTS, - SKCS_NUM_PROTOCOLS, - sizeof(SK_PNMI_CHECKSUM), - SK_PNMI_OFF(Checksum) + SK_PNMI_CHK_OFF(ChecksumRxErrCts), - SK_PNMI_RO, CsumStat, 0}, - {OID_SKGE_CHKSM_TX_OK_CTS, - SKCS_NUM_PROTOCOLS, - sizeof(SK_PNMI_CHECKSUM), - SK_PNMI_OFF(Checksum) + SK_PNMI_CHK_OFF(ChecksumTxOkCts), - SK_PNMI_RO, CsumStat, 0}, - {OID_SKGE_CHKSM_TX_UNABLE_CTS, - SKCS_NUM_PROTOCOLS, - sizeof(SK_PNMI_CHECKSUM), - SK_PNMI_OFF(Checksum) + SK_PNMI_CHK_OFF(ChecksumTxUnableCts), - SK_PNMI_RO, CsumStat, 0}, - {OID_SKGE_STAT_TX, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX}, - {OID_SKGE_STAT_TX_OCTETS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxOctetsOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_OCTET}, - {OID_SKGE_STAT_TX_BROADCAST, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxBroadcastOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_BROADCAST}, - {OID_SKGE_STAT_TX_MULTICAST, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxMulticastOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_MULTICAST}, - {OID_SKGE_STAT_TX_UNICAST, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxUnicastOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_UNICAST}, - {OID_SKGE_STAT_TX_LONGFRAMES, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxLongFramesCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_LONGFRAMES}, - {OID_SKGE_STAT_TX_BURST, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxBurstCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_BURST}, - {OID_SKGE_STAT_TX_PFLOWC, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxPauseMacCtrlCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_PMACC}, - {OID_SKGE_STAT_TX_FLOWC, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxMacCtrlCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_MACC}, - {OID_SKGE_STAT_TX_SINGLE_COL, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxSingleCollisionCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_SINGLE_COL}, - {OID_SKGE_STAT_TX_MULTI_COL, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxMultipleCollisionCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_MULTI_COL}, - {OID_SKGE_STAT_TX_EXCESS_COL, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxExcessiveCollisionCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_EXCESS_COL}, - {OID_SKGE_STAT_TX_LATE_COL, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxLateCollisionCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_LATE_COL}, - {OID_SKGE_STAT_TX_DEFFERAL, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxDeferralCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_DEFFERAL}, - {OID_SKGE_STAT_TX_EXCESS_DEF, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxExcessiveDeferralCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_EXCESS_DEF}, - {OID_SKGE_STAT_TX_UNDERRUN, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxFifoUnderrunCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_UNDERRUN}, - {OID_SKGE_STAT_TX_CARRIER, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxCarrierCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_CARRIER}, -/* {OID_SKGE_STAT_TX_UTIL, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxUtilization), - SK_PNMI_RO, MacPrivateStat, (SK_U16)(-1)}, */ - {OID_SKGE_STAT_TX_64, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTx64Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_64}, - {OID_SKGE_STAT_TX_127, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTx127Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_127}, - {OID_SKGE_STAT_TX_255, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTx255Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_255}, - {OID_SKGE_STAT_TX_511, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTx511Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_511}, - {OID_SKGE_STAT_TX_1023, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTx1023Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_1023}, - {OID_SKGE_STAT_TX_MAX, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxMaxCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_MAX}, - {OID_SKGE_STAT_TX_SYNC, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxSyncCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_SYNC}, - {OID_SKGE_STAT_TX_SYNC_OCTETS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatTxSyncOctetsCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HTX_SYNC_OCTET}, - {OID_SKGE_STAT_RX, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX}, - {OID_SKGE_STAT_RX_OCTETS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxOctetsOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_OCTET}, - {OID_SKGE_STAT_RX_BROADCAST, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxBroadcastOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_BROADCAST}, - {OID_SKGE_STAT_RX_MULTICAST, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxMulticastOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_MULTICAST}, - {OID_SKGE_STAT_RX_UNICAST, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxUnicastOkCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_UNICAST}, - {OID_SKGE_STAT_RX_LONGFRAMES, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxLongFramesCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_LONGFRAMES}, - {OID_SKGE_STAT_RX_PFLOWC, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxPauseMacCtrlCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_PMACC}, - {OID_SKGE_STAT_RX_FLOWC, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxMacCtrlCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_MACC}, - {OID_SKGE_STAT_RX_PFLOWC_ERR, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxPauseMacCtrlErrorCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_PMACC_ERR}, - {OID_SKGE_STAT_RX_FLOWC_UNKWN, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxMacCtrlUnknownCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_MACC_UNKWN}, - {OID_SKGE_STAT_RX_BURST, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxBurstCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_BURST}, - {OID_SKGE_STAT_RX_MISSED, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxMissedCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_MISSED}, - {OID_SKGE_STAT_RX_FRAMING, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxFramingCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_FRAMING}, - {OID_SKGE_STAT_RX_OVERFLOW, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxFifoOverflowCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_OVERFLOW}, - {OID_SKGE_STAT_RX_JABBER, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxJabberCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_JABBER}, - {OID_SKGE_STAT_RX_CARRIER, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxCarrierCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_CARRIER}, - {OID_SKGE_STAT_RX_IR_LENGTH, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxIRLengthCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_IRLENGTH}, - {OID_SKGE_STAT_RX_SYMBOL, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxSymbolCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_SYMBOL}, - {OID_SKGE_STAT_RX_SHORTS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxShortsCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_SHORTS}, - {OID_SKGE_STAT_RX_RUNT, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxRuntCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_RUNT}, - {OID_SKGE_STAT_RX_CEXT, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxCextCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_CEXT}, - {OID_SKGE_STAT_RX_TOO_LONG, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxTooLongCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_TOO_LONG}, - {OID_SKGE_STAT_RX_FCS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxFcsCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_FCS}, -/* {OID_SKGE_STAT_RX_UTIL, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxUtilization), - SK_PNMI_RO, MacPrivateStat, (SK_U16)(-1)}, */ - {OID_SKGE_STAT_RX_64, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRx64Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_64}, - {OID_SKGE_STAT_RX_127, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRx127Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_127}, - {OID_SKGE_STAT_RX_255, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRx255Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_255}, - {OID_SKGE_STAT_RX_511, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRx511Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_511}, - {OID_SKGE_STAT_RX_1023, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRx1023Cts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_1023}, - {OID_SKGE_STAT_RX_MAX, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_STAT), - SK_PNMI_OFF(Stat) + SK_PNMI_STA_OFF(StatRxMaxCts), - SK_PNMI_RO, MacPrivateStat, SK_PNMI_HRX_MAX}, - {OID_SKGE_PHYS_CUR_ADDR, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfMacCurrentAddr), - SK_PNMI_RW, Addr, 0}, - {OID_SKGE_PHYS_FAC_ADDR, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfMacFactoryAddr), - SK_PNMI_RO, Addr, 0}, - {OID_SKGE_PMD, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfPMD), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_CONNECTOR, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfConnector), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_PHY_TYPE, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfPhyType), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_LINK_CAP, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfLinkCapability), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_LINK_MODE, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfLinkMode), - SK_PNMI_RW, MacPrivateConf, 0}, - {OID_SKGE_LINK_MODE_STATUS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfLinkModeStatus), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_LINK_STATUS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfLinkStatus), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_FLOWCTRL_CAP, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfFlowCtrlCapability), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_FLOWCTRL_MODE, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfFlowCtrlMode), - SK_PNMI_RW, MacPrivateConf, 0}, - {OID_SKGE_FLOWCTRL_STATUS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfFlowCtrlStatus), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_PHY_OPERATION_CAP, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfPhyOperationCapability), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_PHY_OPERATION_MODE, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfPhyOperationMode), - SK_PNMI_RW, MacPrivateConf, 0}, - {OID_SKGE_PHY_OPERATION_STATUS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfPhyOperationStatus), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_SPEED_CAP, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfSpeedCapability), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_SPEED_MODE, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfSpeedMode), - SK_PNMI_RW, MacPrivateConf, 0}, - {OID_SKGE_SPEED_STATUS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_CONF), - SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfSpeedStatus), - SK_PNMI_RO, MacPrivateConf, 0}, - {OID_SKGE_TRAP, - 1, - 0, - SK_PNMI_MAI_OFF(Trap), - SK_PNMI_RO, General, 0}, - {OID_SKGE_TRAP_NUMBER, - 1, - 0, - SK_PNMI_MAI_OFF(TrapNumber), - SK_PNMI_RO, General, 0}, - {OID_SKGE_RLMT_MODE, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtMode), - SK_PNMI_RW, Rlmt, 0}, - {OID_SKGE_RLMT_PORT_NUMBER, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtPortNumber), - SK_PNMI_RO, Rlmt, 0}, - {OID_SKGE_RLMT_PORT_ACTIVE, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtPortActive), - SK_PNMI_RO, Rlmt, 0}, - {OID_SKGE_RLMT_PORT_PREFERRED, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtPortPreferred), - SK_PNMI_RW, Rlmt, 0}, - {OID_SKGE_RLMT_CHANGE_CTS, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtChangeCts), - SK_PNMI_RO, Rlmt, 0}, - {OID_SKGE_RLMT_CHANGE_TIME, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtChangeTime), - SK_PNMI_RO, Rlmt, 0}, - {OID_SKGE_RLMT_CHANGE_ESTIM, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtChangeEstimate), - SK_PNMI_RO, Rlmt, 0}, - {OID_SKGE_RLMT_CHANGE_THRES, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtChangeThreshold), - SK_PNMI_RW, Rlmt, 0}, - {OID_SKGE_RLMT_PORT_INDEX, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_RLMT), - SK_PNMI_OFF(Rlmt) + SK_PNMI_RLM_OFF(RlmtIndex), - SK_PNMI_RO, RlmtStat, 0}, - {OID_SKGE_RLMT_STATUS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_RLMT), - SK_PNMI_OFF(Rlmt) + SK_PNMI_RLM_OFF(RlmtStatus), - SK_PNMI_RO, RlmtStat, 0}, - {OID_SKGE_RLMT_TX_HELLO_CTS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_RLMT), - SK_PNMI_OFF(Rlmt) + SK_PNMI_RLM_OFF(RlmtTxHelloCts), - SK_PNMI_RO, RlmtStat, 0}, - {OID_SKGE_RLMT_RX_HELLO_CTS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_RLMT), - SK_PNMI_OFF(Rlmt) + SK_PNMI_RLM_OFF(RlmtRxHelloCts), - SK_PNMI_RO, RlmtStat, 0}, - {OID_SKGE_RLMT_TX_SP_REQ_CTS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_RLMT), - SK_PNMI_OFF(Rlmt) + SK_PNMI_RLM_OFF(RlmtTxSpHelloReqCts), - SK_PNMI_RO, RlmtStat, 0}, - {OID_SKGE_RLMT_RX_SP_CTS, - SK_PNMI_MAC_ENTRIES, - sizeof(SK_PNMI_RLMT), - SK_PNMI_OFF(Rlmt) + SK_PNMI_RLM_OFF(RlmtRxSpHelloCts), - SK_PNMI_RO, RlmtStat, 0}, - {OID_SKGE_RLMT_MONITOR_NUMBER, - 1, - 0, - SK_PNMI_MAI_OFF(RlmtMonitorNumber), - SK_PNMI_RO, General, 0}, - {OID_SKGE_RLMT_MONITOR_INDEX, - SK_PNMI_MONITOR_ENTRIES, - sizeof(SK_PNMI_RLMT_MONITOR), - SK_PNMI_OFF(RlmtMonitor) + SK_PNMI_MON_OFF(RlmtMonitorIndex), - SK_PNMI_RO, Monitor, 0}, - {OID_SKGE_RLMT_MONITOR_ADDR, - SK_PNMI_MONITOR_ENTRIES, - sizeof(SK_PNMI_RLMT_MONITOR), - SK_PNMI_OFF(RlmtMonitor) + SK_PNMI_MON_OFF(RlmtMonitorAddr), - SK_PNMI_RO, Monitor, 0}, - {OID_SKGE_RLMT_MONITOR_ERRS, - SK_PNMI_MONITOR_ENTRIES, - sizeof(SK_PNMI_RLMT_MONITOR), - SK_PNMI_OFF(RlmtMonitor) + SK_PNMI_MON_OFF(RlmtMonitorErrorCts), - SK_PNMI_RO, Monitor, 0}, - {OID_SKGE_RLMT_MONITOR_TIMESTAMP, - SK_PNMI_MONITOR_ENTRIES, - sizeof(SK_PNMI_RLMT_MONITOR), - SK_PNMI_OFF(RlmtMonitor) + SK_PNMI_MON_OFF(RlmtMonitorTimestamp), - SK_PNMI_RO, Monitor, 0}, - {OID_SKGE_RLMT_MONITOR_ADMIN, - SK_PNMI_MONITOR_ENTRIES, - sizeof(SK_PNMI_RLMT_MONITOR), - SK_PNMI_OFF(RlmtMonitor) + SK_PNMI_MON_OFF(RlmtMonitorAdmin), - SK_PNMI_RW, Monitor, 0}, - {OID_SKGE_MTU, - 1, - 0, - SK_PNMI_MAI_OFF(MtuSize), - SK_PNMI_RW, MacPrivateConf, 0}, - {OID_SKGE_VCT_GET, - 0, - 0, - 0, - SK_PNMI_RO, Vct, 0}, - {OID_SKGE_VCT_SET, - 0, - 0, - 0, - SK_PNMI_WO, Vct, 0}, - {OID_SKGE_VCT_STATUS, - 0, - 0, - 0, - SK_PNMI_RO, Vct, 0}, - {OID_SKGE_BOARDLEVEL, - 0, - 0, - 0, - SK_PNMI_RO, General, 0}, -}; - diff --git a/drivers/net/sk98lin/skgepnmi.c b/drivers/net/sk98lin/skgepnmi.c deleted file mode 100644 index b36dd9ac6b29..000000000000 --- a/drivers/net/sk98lin/skgepnmi.c +++ /dev/null @@ -1,8210 +0,0 @@ -/***************************************************************************** - * - * Name: skgepnmi.c - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.111 $ - * Date: $Date: 2003/09/15 13:35:35 $ - * Purpose: Private Network Management Interface - * - ****************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - - -#ifndef _lint -static const char SysKonnectFileId[] = - "@(#) $Id: skgepnmi.c,v 1.111 2003/09/15 13:35:35 tschilli Exp $ (C) Marvell."; -#endif /* !_lint */ - -#include "h/skdrv1st.h" -#include "h/sktypes.h" -#include "h/xmac_ii.h" -#include "h/skdebug.h" -#include "h/skqueue.h" -#include "h/skgepnmi.h" -#include "h/skgesirq.h" -#include "h/skcsum.h" -#include "h/skvpd.h" -#include "h/skgehw.h" -#include "h/skgeinit.h" -#include "h/skdrv2nd.h" -#include "h/skgepnm2.h" -#ifdef SK_POWER_MGMT -#include "h/skgepmgt.h" -#endif -/* defines *******************************************************************/ - -#ifndef DEBUG -#define PNMI_STATIC static -#else /* DEBUG */ -#define PNMI_STATIC -#endif /* DEBUG */ - -/* - * Public Function prototypes - */ -int SkPnmiInit(SK_AC *pAC, SK_IOC IoC, int level); -int SkPnmiSetVar(SK_AC *pAC, SK_IOC IoC, SK_U32 Id, void *pBuf, - unsigned int *pLen, SK_U32 Instance, SK_U32 NetIndex); -int SkPnmiGetStruct(SK_AC *pAC, SK_IOC IoC, void *pBuf, - unsigned int *pLen, SK_U32 NetIndex); -int SkPnmiPreSetStruct(SK_AC *pAC, SK_IOC IoC, void *pBuf, - unsigned int *pLen, SK_U32 NetIndex); -int SkPnmiSetStruct(SK_AC *pAC, SK_IOC IoC, void *pBuf, - unsigned int *pLen, SK_U32 NetIndex); -int SkPnmiEvent(SK_AC *pAC, SK_IOC IoC, SK_U32 Event, SK_EVPARA Param); -int SkPnmiGenIoctl(SK_AC *pAC, SK_IOC IoC, void * pBuf, - unsigned int * pLen, SK_U32 NetIndex); - - -/* - * Private Function prototypes - */ - -PNMI_STATIC SK_U8 CalculateLinkModeStatus(SK_AC *pAC, SK_IOC IoC, unsigned int - PhysPortIndex); -PNMI_STATIC SK_U8 CalculateLinkStatus(SK_AC *pAC, SK_IOC IoC, unsigned int - PhysPortIndex); -PNMI_STATIC void CopyMac(char *pDst, SK_MAC_ADDR *pMac); -PNMI_STATIC void CopyTrapQueue(SK_AC *pAC, char *pDstBuf); -PNMI_STATIC SK_U64 GetPhysStatVal(SK_AC *pAC, SK_IOC IoC, - unsigned int PhysPortIndex, unsigned int StatIndex); -PNMI_STATIC SK_U64 GetStatVal(SK_AC *pAC, SK_IOC IoC, unsigned int LogPortIndex, - unsigned int StatIndex, SK_U32 NetIndex); -PNMI_STATIC char* GetTrapEntry(SK_AC *pAC, SK_U32 TrapId, unsigned int Size); -PNMI_STATIC void GetTrapQueueLen(SK_AC *pAC, unsigned int *pLen, - unsigned int *pEntries); -PNMI_STATIC int GetVpdKeyArr(SK_AC *pAC, SK_IOC IoC, char *pKeyArr, - unsigned int KeyArrLen, unsigned int *pKeyNo); -PNMI_STATIC int LookupId(SK_U32 Id); -PNMI_STATIC int MacUpdate(SK_AC *pAC, SK_IOC IoC, unsigned int FirstMac, - unsigned int LastMac); -PNMI_STATIC int PnmiStruct(SK_AC *pAC, SK_IOC IoC, int Action, char *pBuf, - unsigned int *pLen, SK_U32 NetIndex); -PNMI_STATIC int PnmiVar(SK_AC *pAC, SK_IOC IoC, int Action, SK_U32 Id, - char *pBuf, unsigned int *pLen, SK_U32 Instance, SK_U32 NetIndex); -PNMI_STATIC void QueueRlmtNewMacTrap(SK_AC *pAC, unsigned int ActiveMac); -PNMI_STATIC void QueueRlmtPortTrap(SK_AC *pAC, SK_U32 TrapId, - unsigned int PortIndex); -PNMI_STATIC void QueueSensorTrap(SK_AC *pAC, SK_U32 TrapId, - unsigned int SensorIndex); -PNMI_STATIC void QueueSimpleTrap(SK_AC *pAC, SK_U32 TrapId); -PNMI_STATIC void ResetCounter(SK_AC *pAC, SK_IOC IoC, SK_U32 NetIndex); -PNMI_STATIC int RlmtUpdate(SK_AC *pAC, SK_IOC IoC, SK_U32 NetIndex); -PNMI_STATIC int SirqUpdate(SK_AC *pAC, SK_IOC IoC); -PNMI_STATIC void VirtualConf(SK_AC *pAC, SK_IOC IoC, SK_U32 Id, char *pBuf); -PNMI_STATIC int Vct(SK_AC *pAC, SK_IOC IoC, int Action, SK_U32 Id, char *pBuf, - unsigned int *pLen, SK_U32 Instance, unsigned int TableIndex, SK_U32 NetIndex); -PNMI_STATIC void CheckVctStatus(SK_AC *, SK_IOC, char *, SK_U32, SK_U32); - -/* - * Table to correlate OID with handler function and index to - * hardware register stored in StatAddress if applicable. - */ -#include "skgemib.c" - -/* global variables **********************************************************/ - -/* - * Overflow status register bit table and corresponding counter - * dependent on MAC type - the number relates to the size of overflow - * mask returned by the pFnMacOverflow function - */ -PNMI_STATIC const SK_U16 StatOvrflwBit[][SK_PNMI_MAC_TYPES] = { -/* Bit0 */ { SK_PNMI_HTX, SK_PNMI_HTX_UNICAST}, -/* Bit1 */ { SK_PNMI_HTX_OCTETHIGH, SK_PNMI_HTX_BROADCAST}, -/* Bit2 */ { SK_PNMI_HTX_OCTETLOW, SK_PNMI_HTX_PMACC}, -/* Bit3 */ { SK_PNMI_HTX_BROADCAST, SK_PNMI_HTX_MULTICAST}, -/* Bit4 */ { SK_PNMI_HTX_MULTICAST, SK_PNMI_HTX_OCTETLOW}, -/* Bit5 */ { SK_PNMI_HTX_UNICAST, SK_PNMI_HTX_OCTETHIGH}, -/* Bit6 */ { SK_PNMI_HTX_LONGFRAMES, SK_PNMI_HTX_64}, -/* Bit7 */ { SK_PNMI_HTX_BURST, SK_PNMI_HTX_127}, -/* Bit8 */ { SK_PNMI_HTX_PMACC, SK_PNMI_HTX_255}, -/* Bit9 */ { SK_PNMI_HTX_MACC, SK_PNMI_HTX_511}, -/* Bit10 */ { SK_PNMI_HTX_SINGLE_COL, SK_PNMI_HTX_1023}, -/* Bit11 */ { SK_PNMI_HTX_MULTI_COL, SK_PNMI_HTX_MAX}, -/* Bit12 */ { SK_PNMI_HTX_EXCESS_COL, SK_PNMI_HTX_LONGFRAMES}, -/* Bit13 */ { SK_PNMI_HTX_LATE_COL, SK_PNMI_HTX_RESERVED}, -/* Bit14 */ { SK_PNMI_HTX_DEFFERAL, SK_PNMI_HTX_COL}, -/* Bit15 */ { SK_PNMI_HTX_EXCESS_DEF, SK_PNMI_HTX_LATE_COL}, -/* Bit16 */ { SK_PNMI_HTX_UNDERRUN, SK_PNMI_HTX_EXCESS_COL}, -/* Bit17 */ { SK_PNMI_HTX_CARRIER, SK_PNMI_HTX_MULTI_COL}, -/* Bit18 */ { SK_PNMI_HTX_UTILUNDER, SK_PNMI_HTX_SINGLE_COL}, -/* Bit19 */ { SK_PNMI_HTX_UTILOVER, SK_PNMI_HTX_UNDERRUN}, -/* Bit20 */ { SK_PNMI_HTX_64, SK_PNMI_HTX_RESERVED}, -/* Bit21 */ { SK_PNMI_HTX_127, SK_PNMI_HTX_RESERVED}, -/* Bit22 */ { SK_PNMI_HTX_255, SK_PNMI_HTX_RESERVED}, -/* Bit23 */ { SK_PNMI_HTX_511, SK_PNMI_HTX_RESERVED}, -/* Bit24 */ { SK_PNMI_HTX_1023, SK_PNMI_HTX_RESERVED}, -/* Bit25 */ { SK_PNMI_HTX_MAX, SK_PNMI_HTX_RESERVED}, -/* Bit26 */ { SK_PNMI_HTX_RESERVED, SK_PNMI_HTX_RESERVED}, -/* Bit27 */ { SK_PNMI_HTX_RESERVED, SK_PNMI_HTX_RESERVED}, -/* Bit28 */ { SK_PNMI_HTX_RESERVED, SK_PNMI_HTX_RESERVED}, -/* Bit29 */ { SK_PNMI_HTX_RESERVED, SK_PNMI_HTX_RESERVED}, -/* Bit30 */ { SK_PNMI_HTX_RESERVED, SK_PNMI_HTX_RESERVED}, -/* Bit31 */ { SK_PNMI_HTX_RESERVED, SK_PNMI_HTX_RESERVED}, -/* Bit32 */ { SK_PNMI_HRX, SK_PNMI_HRX_UNICAST}, -/* Bit33 */ { SK_PNMI_HRX_OCTETHIGH, SK_PNMI_HRX_BROADCAST}, -/* Bit34 */ { SK_PNMI_HRX_OCTETLOW, SK_PNMI_HRX_PMACC}, -/* Bit35 */ { SK_PNMI_HRX_BROADCAST, SK_PNMI_HRX_MULTICAST}, -/* Bit36 */ { SK_PNMI_HRX_MULTICAST, SK_PNMI_HRX_FCS}, -/* Bit37 */ { SK_PNMI_HRX_UNICAST, SK_PNMI_HRX_RESERVED}, -/* Bit38 */ { SK_PNMI_HRX_PMACC, SK_PNMI_HRX_OCTETLOW}, -/* Bit39 */ { SK_PNMI_HRX_MACC, SK_PNMI_HRX_OCTETHIGH}, -/* Bit40 */ { SK_PNMI_HRX_PMACC_ERR, SK_PNMI_HRX_BADOCTETLOW}, -/* Bit41 */ { SK_PNMI_HRX_MACC_UNKWN, SK_PNMI_HRX_BADOCTETHIGH}, -/* Bit42 */ { SK_PNMI_HRX_BURST, SK_PNMI_HRX_UNDERSIZE}, -/* Bit43 */ { SK_PNMI_HRX_MISSED, SK_PNMI_HRX_RUNT}, -/* Bit44 */ { SK_PNMI_HRX_FRAMING, SK_PNMI_HRX_64}, -/* Bit45 */ { SK_PNMI_HRX_OVERFLOW, SK_PNMI_HRX_127}, -/* Bit46 */ { SK_PNMI_HRX_JABBER, SK_PNMI_HRX_255}, -/* Bit47 */ { SK_PNMI_HRX_CARRIER, SK_PNMI_HRX_511}, -/* Bit48 */ { SK_PNMI_HRX_IRLENGTH, SK_PNMI_HRX_1023}, -/* Bit49 */ { SK_PNMI_HRX_SYMBOL, SK_PNMI_HRX_MAX}, -/* Bit50 */ { SK_PNMI_HRX_SHORTS, SK_PNMI_HRX_LONGFRAMES}, -/* Bit51 */ { SK_PNMI_HRX_RUNT, SK_PNMI_HRX_TOO_LONG}, -/* Bit52 */ { SK_PNMI_HRX_TOO_LONG, SK_PNMI_HRX_JABBER}, -/* Bit53 */ { SK_PNMI_HRX_FCS, SK_PNMI_HRX_RESERVED}, -/* Bit54 */ { SK_PNMI_HRX_RESERVED, SK_PNMI_HRX_OVERFLOW}, -/* Bit55 */ { SK_PNMI_HRX_CEXT, SK_PNMI_HRX_RESERVED}, -/* Bit56 */ { SK_PNMI_HRX_UTILUNDER, SK_PNMI_HRX_RESERVED}, -/* Bit57 */ { SK_PNMI_HRX_UTILOVER, SK_PNMI_HRX_RESERVED}, -/* Bit58 */ { SK_PNMI_HRX_64, SK_PNMI_HRX_RESERVED}, -/* Bit59 */ { SK_PNMI_HRX_127, SK_PNMI_HRX_RESERVED}, -/* Bit60 */ { SK_PNMI_HRX_255, SK_PNMI_HRX_RESERVED}, -/* Bit61 */ { SK_PNMI_HRX_511, SK_PNMI_HRX_RESERVED}, -/* Bit62 */ { SK_PNMI_HRX_1023, SK_PNMI_HRX_RESERVED}, -/* Bit63 */ { SK_PNMI_HRX_MAX, SK_PNMI_HRX_RESERVED} -}; - -/* - * Table for hardware register saving on resets and port switches - */ -PNMI_STATIC const SK_PNMI_STATADDR StatAddr[SK_PNMI_MAX_IDX][SK_PNMI_MAC_TYPES] = { - /* SK_PNMI_HTX */ - {{XM_TXF_OK, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_OCTETHIGH */ - {{XM_TXO_OK_HI, SK_TRUE}, {GM_TXO_OK_HI, SK_TRUE}}, - /* SK_PNMI_HTX_OCTETLOW */ - {{XM_TXO_OK_LO, SK_FALSE}, {GM_TXO_OK_LO, SK_FALSE}}, - /* SK_PNMI_HTX_BROADCAST */ - {{XM_TXF_BC_OK, SK_TRUE}, {GM_TXF_BC_OK, SK_TRUE}}, - /* SK_PNMI_HTX_MULTICAST */ - {{XM_TXF_MC_OK, SK_TRUE}, {GM_TXF_MC_OK, SK_TRUE}}, - /* SK_PNMI_HTX_UNICAST */ - {{XM_TXF_UC_OK, SK_TRUE}, {GM_TXF_UC_OK, SK_TRUE}}, - /* SK_PNMI_HTX_BURST */ - {{XM_TXE_BURST, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_PMACC */ - {{XM_TXF_MPAUSE, SK_TRUE}, {GM_TXF_MPAUSE, SK_TRUE}}, - /* SK_PNMI_HTX_MACC */ - {{XM_TXF_MCTRL, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_COL */ - {{0, SK_FALSE}, {GM_TXF_COL, SK_TRUE}}, - /* SK_PNMI_HTX_SINGLE_COL */ - {{XM_TXF_SNG_COL, SK_TRUE}, {GM_TXF_SNG_COL, SK_TRUE}}, - /* SK_PNMI_HTX_MULTI_COL */ - {{XM_TXF_MUL_COL, SK_TRUE}, {GM_TXF_MUL_COL, SK_TRUE}}, - /* SK_PNMI_HTX_EXCESS_COL */ - {{XM_TXF_ABO_COL, SK_TRUE}, {GM_TXF_ABO_COL, SK_TRUE}}, - /* SK_PNMI_HTX_LATE_COL */ - {{XM_TXF_LAT_COL, SK_TRUE}, {GM_TXF_LAT_COL, SK_TRUE}}, - /* SK_PNMI_HTX_DEFFERAL */ - {{XM_TXF_DEF, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_EXCESS_DEF */ - {{XM_TXF_EX_DEF, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_UNDERRUN */ - {{XM_TXE_FIFO_UR, SK_TRUE}, {GM_TXE_FIFO_UR, SK_TRUE}}, - /* SK_PNMI_HTX_CARRIER */ - {{XM_TXE_CS_ERR, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_UTILUNDER */ - {{0, SK_FALSE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_UTILOVER */ - {{0, SK_FALSE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_64 */ - {{XM_TXF_64B, SK_TRUE}, {GM_TXF_64B, SK_TRUE}}, - /* SK_PNMI_HTX_127 */ - {{XM_TXF_127B, SK_TRUE}, {GM_TXF_127B, SK_TRUE}}, - /* SK_PNMI_HTX_255 */ - {{XM_TXF_255B, SK_TRUE}, {GM_TXF_255B, SK_TRUE}}, - /* SK_PNMI_HTX_511 */ - {{XM_TXF_511B, SK_TRUE}, {GM_TXF_511B, SK_TRUE}}, - /* SK_PNMI_HTX_1023 */ - {{XM_TXF_1023B, SK_TRUE}, {GM_TXF_1023B, SK_TRUE}}, - /* SK_PNMI_HTX_MAX */ - {{XM_TXF_MAX_SZ, SK_TRUE}, {GM_TXF_1518B, SK_TRUE}}, - /* SK_PNMI_HTX_LONGFRAMES */ - {{XM_TXF_LONG, SK_TRUE}, {GM_TXF_MAX_SZ, SK_TRUE}}, - /* SK_PNMI_HTX_SYNC */ - {{0, SK_FALSE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_SYNC_OCTET */ - {{0, SK_FALSE}, {0, SK_FALSE}}, - /* SK_PNMI_HTX_RESERVED */ - {{0, SK_FALSE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX */ - {{XM_RXF_OK, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_OCTETHIGH */ - {{XM_RXO_OK_HI, SK_TRUE}, {GM_RXO_OK_HI, SK_TRUE}}, - /* SK_PNMI_HRX_OCTETLOW */ - {{XM_RXO_OK_LO, SK_FALSE}, {GM_RXO_OK_LO, SK_FALSE}}, - /* SK_PNMI_HRX_BADOCTETHIGH */ - {{0, SK_FALSE}, {GM_RXO_ERR_HI, SK_TRUE}}, - /* SK_PNMI_HRX_BADOCTETLOW */ - {{0, SK_FALSE}, {GM_RXO_ERR_LO, SK_TRUE}}, - /* SK_PNMI_HRX_BROADCAST */ - {{XM_RXF_BC_OK, SK_TRUE}, {GM_RXF_BC_OK, SK_TRUE}}, - /* SK_PNMI_HRX_MULTICAST */ - {{XM_RXF_MC_OK, SK_TRUE}, {GM_RXF_MC_OK, SK_TRUE}}, - /* SK_PNMI_HRX_UNICAST */ - {{XM_RXF_UC_OK, SK_TRUE}, {GM_RXF_UC_OK, SK_TRUE}}, - /* SK_PNMI_HRX_PMACC */ - {{XM_RXF_MPAUSE, SK_TRUE}, {GM_RXF_MPAUSE, SK_TRUE}}, - /* SK_PNMI_HRX_MACC */ - {{XM_RXF_MCTRL, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_PMACC_ERR */ - {{XM_RXF_INV_MP, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_MACC_UNKWN */ - {{XM_RXF_INV_MOC, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_BURST */ - {{XM_RXE_BURST, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_MISSED */ - {{XM_RXE_FMISS, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_FRAMING */ - {{XM_RXF_FRA_ERR, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_UNDERSIZE */ - {{0, SK_FALSE}, {GM_RXF_SHT, SK_TRUE}}, - /* SK_PNMI_HRX_OVERFLOW */ - {{XM_RXE_FIFO_OV, SK_TRUE}, {GM_RXE_FIFO_OV, SK_TRUE}}, - /* SK_PNMI_HRX_JABBER */ - {{XM_RXF_JAB_PKT, SK_TRUE}, {GM_RXF_JAB_PKT, SK_TRUE}}, - /* SK_PNMI_HRX_CARRIER */ - {{XM_RXE_CAR_ERR, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_IRLENGTH */ - {{XM_RXF_LEN_ERR, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_SYMBOL */ - {{XM_RXE_SYM_ERR, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_SHORTS */ - {{XM_RXE_SHT_ERR, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_RUNT */ - {{XM_RXE_RUNT, SK_TRUE}, {GM_RXE_FRAG, SK_TRUE}}, - /* SK_PNMI_HRX_TOO_LONG */ - {{XM_RXF_LNG_ERR, SK_TRUE}, {GM_RXF_LNG_ERR, SK_TRUE}}, - /* SK_PNMI_HRX_FCS */ - {{XM_RXF_FCS_ERR, SK_TRUE}, {GM_RXF_FCS_ERR, SK_TRUE}}, - /* SK_PNMI_HRX_CEXT */ - {{XM_RXF_CEX_ERR, SK_TRUE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_UTILUNDER */ - {{0, SK_FALSE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_UTILOVER */ - {{0, SK_FALSE}, {0, SK_FALSE}}, - /* SK_PNMI_HRX_64 */ - {{XM_RXF_64B, SK_TRUE}, {GM_RXF_64B, SK_TRUE}}, - /* SK_PNMI_HRX_127 */ - {{XM_RXF_127B, SK_TRUE}, {GM_RXF_127B, SK_TRUE}}, - /* SK_PNMI_HRX_255 */ - {{XM_RXF_255B, SK_TRUE}, {GM_RXF_255B, SK_TRUE}}, - /* SK_PNMI_HRX_511 */ - {{XM_RXF_511B, SK_TRUE}, {GM_RXF_511B, SK_TRUE}}, - /* SK_PNMI_HRX_1023 */ - {{XM_RXF_1023B, SK_TRUE}, {GM_RXF_1023B, SK_TRUE}}, - /* SK_PNMI_HRX_MAX */ - {{XM_RXF_MAX_SZ, SK_TRUE}, {GM_RXF_1518B, SK_TRUE}}, - /* SK_PNMI_HRX_LONGFRAMES */ - {{0, SK_FALSE}, {GM_RXF_MAX_SZ, SK_TRUE}}, - /* SK_PNMI_HRX_RESERVED */ - {{0, SK_FALSE}, {0, SK_FALSE}} -}; - - -/***************************************************************************** - * - * Public functions - * - */ - -/***************************************************************************** - * - * SkPnmiInit - Init function of PNMI - * - * Description: - * SK_INIT_DATA: Initialises the data structures - * SK_INIT_IO: Resets the XMAC statistics, determines the device and - * connector type. - * SK_INIT_RUN: Starts a timer event for port switch per hour - * calculation. - * - * Returns: - * Always 0 - */ -int SkPnmiInit( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Level) /* Initialization level */ -{ - unsigned int PortMax; /* Number of ports */ - unsigned int PortIndex; /* Current port index in loop */ - SK_U16 Val16; /* Multiple purpose 16 bit variable */ - SK_U8 Val8; /* Mulitple purpose 8 bit variable */ - SK_EVPARA EventParam; /* Event struct for timer event */ - SK_PNMI_VCT *pVctBackupData; - - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: SkPnmiInit: Called, level=%d\n", Level)); - - switch (Level) { - - case SK_INIT_DATA: - SK_MEMSET((char *)&pAC->Pnmi, 0, sizeof(pAC->Pnmi)); - pAC->Pnmi.TrapBufFree = SK_PNMI_TRAP_QUEUE_LEN; - pAC->Pnmi.StartUpTime = SK_PNMI_HUNDREDS_SEC(SkOsGetTime(pAC)); - pAC->Pnmi.RlmtChangeThreshold = SK_PNMI_DEF_RLMT_CHG_THRES; - for (PortIndex = 0; PortIndex < SK_MAX_MACS; PortIndex ++) { - - pAC->Pnmi.Port[PortIndex].ActiveFlag = SK_FALSE; - pAC->Pnmi.DualNetActiveFlag = SK_FALSE; - } - -#ifdef SK_PNMI_CHECK - if (SK_PNMI_MAX_IDX != SK_PNMI_CNT_NO) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR049, SK_PNMI_ERR049MSG); - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_INIT | SK_DBGCAT_FATAL, - ("CounterOffset struct size (%d) differs from" - "SK_PNMI_MAX_IDX (%d)\n", - SK_PNMI_CNT_NO, SK_PNMI_MAX_IDX)); - } - - if (SK_PNMI_MAX_IDX != - (sizeof(StatAddr) / (sizeof(SK_PNMI_STATADDR) * SK_PNMI_MAC_TYPES))) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR050, SK_PNMI_ERR050MSG); - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_INIT | SK_DBGCAT_FATAL, - ("StatAddr table size (%d) differs from " - "SK_PNMI_MAX_IDX (%d)\n", - (sizeof(StatAddr) / - (sizeof(SK_PNMI_STATADDR) * SK_PNMI_MAC_TYPES)), - SK_PNMI_MAX_IDX)); - } -#endif /* SK_PNMI_CHECK */ - break; - - case SK_INIT_IO: - /* - * Reset MAC counters - */ - PortMax = pAC->GIni.GIMacsFound; - - for (PortIndex = 0; PortIndex < PortMax; PortIndex ++) { - - pAC->GIni.GIFunc.pFnMacResetCounter(pAC, IoC, PortIndex); - } - - /* Initialize DSP variables for Vct() to 0xff => Never written! */ - for (PortIndex = 0; PortIndex < PortMax; PortIndex ++) { - pAC->GIni.GP[PortIndex].PCableLen = 0xff; - pVctBackupData = &pAC->Pnmi.VctBackup[PortIndex]; - pVctBackupData->PCableLen = 0xff; - } - - /* - * Get pci bus speed - */ - SK_IN16(IoC, B0_CTST, &Val16); - if ((Val16 & CS_BUS_CLOCK) == 0) { - - pAC->Pnmi.PciBusSpeed = 33; - } - else { - pAC->Pnmi.PciBusSpeed = 66; - } - - /* - * Get pci bus width - */ - SK_IN16(IoC, B0_CTST, &Val16); - if ((Val16 & CS_BUS_SLOT_SZ) == 0) { - - pAC->Pnmi.PciBusWidth = 32; - } - else { - pAC->Pnmi.PciBusWidth = 64; - } - - /* - * Get chipset - */ - switch (pAC->GIni.GIChipId) { - case CHIP_ID_GENESIS: - pAC->Pnmi.Chipset = SK_PNMI_CHIPSET_XMAC; - break; - - case CHIP_ID_YUKON: - pAC->Pnmi.Chipset = SK_PNMI_CHIPSET_YUKON; - break; - - default: - break; - } - - /* - * Get PMD and DeviceType - */ - SK_IN8(IoC, B2_PMD_TYP, &Val8); - switch (Val8) { - case 'S': - pAC->Pnmi.PMD = 3; - if (pAC->GIni.GIMacsFound > 1) { - - pAC->Pnmi.DeviceType = 0x00020002; - } - else { - pAC->Pnmi.DeviceType = 0x00020001; - } - break; - - case 'L': - pAC->Pnmi.PMD = 2; - if (pAC->GIni.GIMacsFound > 1) { - - pAC->Pnmi.DeviceType = 0x00020004; - } - else { - pAC->Pnmi.DeviceType = 0x00020003; - } - break; - - case 'C': - pAC->Pnmi.PMD = 4; - if (pAC->GIni.GIMacsFound > 1) { - - pAC->Pnmi.DeviceType = 0x00020006; - } - else { - pAC->Pnmi.DeviceType = 0x00020005; - } - break; - - case 'T': - pAC->Pnmi.PMD = 5; - if (pAC->GIni.GIMacsFound > 1) { - - pAC->Pnmi.DeviceType = 0x00020008; - } - else { - pAC->Pnmi.DeviceType = 0x00020007; - } - break; - - default : - pAC->Pnmi.PMD = 1; - pAC->Pnmi.DeviceType = 0; - break; - } - - /* - * Get connector - */ - SK_IN8(IoC, B2_CONN_TYP, &Val8); - switch (Val8) { - case 'C': - pAC->Pnmi.Connector = 2; - break; - - case 'D': - pAC->Pnmi.Connector = 3; - break; - - case 'F': - pAC->Pnmi.Connector = 4; - break; - - case 'J': - pAC->Pnmi.Connector = 5; - break; - - case 'V': - pAC->Pnmi.Connector = 6; - break; - - default: - pAC->Pnmi.Connector = 1; - break; - } - break; - - case SK_INIT_RUN: - /* - * Start timer for RLMT change counter - */ - SK_MEMSET((char *)&EventParam, 0, sizeof(EventParam)); - SkTimerStart(pAC, IoC, &pAC->Pnmi.RlmtChangeEstimate.EstTimer, - 28125000, SKGE_PNMI, SK_PNMI_EVT_CHG_EST_TIMER, - EventParam); - break; - - default: - break; /* Nothing todo */ - } - - return (0); -} - -/***************************************************************************** - * - * SkPnmiGetVar - Retrieves the value of a single OID - * - * Description: - * Calls a general sub-function for all this stuff. If the instance - * -1 is passed, the values of all instances are returned in an - * array of values. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed - * SK_PNMI_ERR_GENERAL A general severe internal error occured - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to take - * the data. - * SK_PNMI_ERR_UNKNOWN_OID The requested OID is unknown - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -static int SkPnmiGetVar( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -SK_U32 Id, /* Object ID that is to be processed */ -void *pBuf, /* Buffer to which the management data will be copied */ -unsigned int *pLen, /* On call: buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: SkPnmiGetVar: Called, Id=0x%x, BufLen=%d, Instance=%d, NetIndex=%d\n", - Id, *pLen, Instance, NetIndex)); - - return (PnmiVar(pAC, IoC, SK_PNMI_GET, Id, (char *)pBuf, pLen, - Instance, NetIndex)); -} - -/***************************************************************************** - * - * SkPnmiPreSetVar - Presets the value of a single OID - * - * Description: - * Calls a general sub-function for all this stuff. The preset does - * the same as a set, but returns just before finally setting the - * new value. This is useful to check if a set might be successfull. - * If the instance -1 is passed, an array of values is supposed and - * all instances of the OID will be set. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_OID The requested OID is unknown. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -static int SkPnmiPreSetVar( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -SK_U32 Id, /* Object ID that is to be processed */ -void *pBuf, /* Buffer to which the management data will be copied */ -unsigned int *pLen, /* Total length of management data */ -SK_U32 Instance, /* Instance (1..n) that is to be set or -1 */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: SkPnmiPreSetVar: Called, Id=0x%x, BufLen=%d, Instance=%d, NetIndex=%d\n", - Id, *pLen, Instance, NetIndex)); - - - return (PnmiVar(pAC, IoC, SK_PNMI_PRESET, Id, (char *)pBuf, pLen, - Instance, NetIndex)); -} - -/***************************************************************************** - * - * SkPnmiSetVar - Sets the value of a single OID - * - * Description: - * Calls a general sub-function for all this stuff. The preset does - * the same as a set, but returns just before finally setting the - * new value. This is useful to check if a set might be successfull. - * If the instance -1 is passed, an array of values is supposed and - * all instances of the OID will be set. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_OID The requested OID is unknown. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -int SkPnmiSetVar( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -SK_U32 Id, /* Object ID that is to be processed */ -void *pBuf, /* Buffer to which the management data will be copied */ -unsigned int *pLen, /* Total length of management data */ -SK_U32 Instance, /* Instance (1..n) that is to be set or -1 */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: SkPnmiSetVar: Called, Id=0x%x, BufLen=%d, Instance=%d, NetIndex=%d\n", - Id, *pLen, Instance, NetIndex)); - - return (PnmiVar(pAC, IoC, SK_PNMI_SET, Id, (char *)pBuf, pLen, - Instance, NetIndex)); -} - -/***************************************************************************** - * - * SkPnmiGetStruct - Retrieves the management database in SK_PNMI_STRUCT_DATA - * - * Description: - * Runs through the IdTable, queries the single OIDs and stores the - * returned data into the management database structure - * SK_PNMI_STRUCT_DATA. The offset of the OID in the structure - * is stored in the IdTable. The return value of the function will also - * be stored in SK_PNMI_STRUCT_DATA if the passed buffer has the - * minimum size of SK_PNMI_MIN_STRUCT_SIZE. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed - * SK_PNMI_ERR_GENERAL A general severe internal error occured - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to take - * the data. - * SK_PNMI_ERR_UNKNOWN_NET The requested NetIndex doesn't exist - */ -int SkPnmiGetStruct( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -void *pBuf, /* Buffer to which the management data will be copied. */ -unsigned int *pLen, /* Length of buffer */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - int Ret; - unsigned int TableIndex; - unsigned int DstOffset; - unsigned int InstanceNo; - unsigned int InstanceCnt; - SK_U32 Instance; - unsigned int TmpLen; - char KeyArr[SK_PNMI_VPD_ENTRIES][SK_PNMI_VPD_KEY_SIZE]; - - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: SkPnmiGetStruct: Called, BufLen=%d, NetIndex=%d\n", - *pLen, NetIndex)); - - if (*pLen < SK_PNMI_STRUCT_SIZE) { - - if (*pLen >= SK_PNMI_MIN_STRUCT_SIZE) { - - SK_PNMI_SET_STAT(pBuf, SK_PNMI_ERR_TOO_SHORT, - (SK_U32)(-1)); - } - - *pLen = SK_PNMI_STRUCT_SIZE; - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* - * Check NetIndex - */ - if (NetIndex >= pAC->Rlmt.NumNets) { - return (SK_PNMI_ERR_UNKNOWN_NET); - } - - /* Update statistic */ - SK_PNMI_CHECKFLAGS("SkPnmiGetStruct: On call"); - - if ((Ret = MacUpdate(pAC, IoC, 0, pAC->GIni.GIMacsFound - 1)) != - SK_PNMI_ERR_OK) { - - SK_PNMI_SET_STAT(pBuf, Ret, (SK_U32)(-1)); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (Ret); - } - - if ((Ret = RlmtUpdate(pAC, IoC, NetIndex)) != SK_PNMI_ERR_OK) { - - SK_PNMI_SET_STAT(pBuf, Ret, (SK_U32)(-1)); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (Ret); - } - - if ((Ret = SirqUpdate(pAC, IoC)) != SK_PNMI_ERR_OK) { - - SK_PNMI_SET_STAT(pBuf, Ret, (SK_U32)(-1)); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (Ret); - } - - /* - * Increment semaphores to indicate that an update was - * already done - */ - pAC->Pnmi.MacUpdatedFlag ++; - pAC->Pnmi.RlmtUpdatedFlag ++; - pAC->Pnmi.SirqUpdatedFlag ++; - - /* Get vpd keys for instance calculation */ - Ret = GetVpdKeyArr(pAC, IoC, &KeyArr[0][0], sizeof(KeyArr), &TmpLen); - if (Ret != SK_PNMI_ERR_OK) { - - pAC->Pnmi.MacUpdatedFlag --; - pAC->Pnmi.RlmtUpdatedFlag --; - pAC->Pnmi.SirqUpdatedFlag --; - - SK_PNMI_CHECKFLAGS("SkPnmiGetStruct: On return"); - SK_PNMI_SET_STAT(pBuf, Ret, (SK_U32)(-1)); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (SK_PNMI_ERR_GENERAL); - } - - /* Retrieve values */ - SK_MEMSET((char *)pBuf, 0, SK_PNMI_STRUCT_SIZE); - for (TableIndex = 0; TableIndex < ID_TABLE_SIZE; TableIndex ++) { - - InstanceNo = IdTable[TableIndex].InstanceNo; - for (InstanceCnt = 1; InstanceCnt <= InstanceNo; - InstanceCnt ++) { - - DstOffset = IdTable[TableIndex].Offset + - (InstanceCnt - 1) * - IdTable[TableIndex].StructSize; - - /* - * For the VPD the instance is not an index number - * but the key itself. Determin with the instance - * counter the VPD key to be used. - */ - if (IdTable[TableIndex].Id == OID_SKGE_VPD_KEY || - IdTable[TableIndex].Id == OID_SKGE_VPD_VALUE || - IdTable[TableIndex].Id == OID_SKGE_VPD_ACCESS || - IdTable[TableIndex].Id == OID_SKGE_VPD_ACTION) { - - SK_STRNCPY((char *)&Instance, KeyArr[InstanceCnt - 1], 4); - } - else { - Instance = (SK_U32)InstanceCnt; - } - - TmpLen = *pLen - DstOffset; - Ret = IdTable[TableIndex].Func(pAC, IoC, SK_PNMI_GET, - IdTable[TableIndex].Id, (char *)pBuf + - DstOffset, &TmpLen, Instance, TableIndex, NetIndex); - - /* - * An unknown instance error means that we reached - * the last instance of that variable. Proceed with - * the next OID in the table and ignore the return - * code. - */ - if (Ret == SK_PNMI_ERR_UNKNOWN_INST) { - - break; - } - - if (Ret != SK_PNMI_ERR_OK) { - - pAC->Pnmi.MacUpdatedFlag --; - pAC->Pnmi.RlmtUpdatedFlag --; - pAC->Pnmi.SirqUpdatedFlag --; - - SK_PNMI_CHECKFLAGS("SkPnmiGetStruct: On return"); - SK_PNMI_SET_STAT(pBuf, Ret, DstOffset); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (Ret); - } - } - } - - pAC->Pnmi.MacUpdatedFlag --; - pAC->Pnmi.RlmtUpdatedFlag --; - pAC->Pnmi.SirqUpdatedFlag --; - - *pLen = SK_PNMI_STRUCT_SIZE; - SK_PNMI_CHECKFLAGS("SkPnmiGetStruct: On return"); - SK_PNMI_SET_STAT(pBuf, SK_PNMI_ERR_OK, (SK_U32)(-1)); - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * SkPnmiPreSetStruct - Presets the management database in SK_PNMI_STRUCT_DATA - * - * Description: - * Calls a general sub-function for all this set stuff. The preset does - * the same as a set, but returns just before finally setting the - * new value. This is useful to check if a set might be successfull. - * The sub-function runs through the IdTable, checks which OIDs are able - * to set, and calls the handler function of the OID to perform the - * preset. The return value of the function will also be stored in - * SK_PNMI_STRUCT_DATA if the passed buffer has the minimum size of - * SK_PNMI_MIN_STRUCT_SIZE. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - */ -int SkPnmiPreSetStruct( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -void *pBuf, /* Buffer which contains the data to be set */ -unsigned int *pLen, /* Length of buffer */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: SkPnmiPreSetStruct: Called, BufLen=%d, NetIndex=%d\n", - *pLen, NetIndex)); - - return (PnmiStruct(pAC, IoC, SK_PNMI_PRESET, (char *)pBuf, - pLen, NetIndex)); -} - -/***************************************************************************** - * - * SkPnmiSetStruct - Sets the management database in SK_PNMI_STRUCT_DATA - * - * Description: - * Calls a general sub-function for all this set stuff. The return value - * of the function will also be stored in SK_PNMI_STRUCT_DATA if the - * passed buffer has the minimum size of SK_PNMI_MIN_STRUCT_SIZE. - * The sub-function runs through the IdTable, checks which OIDs are able - * to set, and calls the handler function of the OID to perform the - * set. The return value of the function will also be stored in - * SK_PNMI_STRUCT_DATA if the passed buffer has the minimum size of - * SK_PNMI_MIN_STRUCT_SIZE. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - */ -int SkPnmiSetStruct( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -void *pBuf, /* Buffer which contains the data to be set */ -unsigned int *pLen, /* Length of buffer */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: SkPnmiSetStruct: Called, BufLen=%d, NetIndex=%d\n", - *pLen, NetIndex)); - - return (PnmiStruct(pAC, IoC, SK_PNMI_SET, (char *)pBuf, - pLen, NetIndex)); -} - -/***************************************************************************** - * - * SkPnmiEvent - Event handler - * - * Description: - * Handles the following events: - * SK_PNMI_EVT_SIRQ_OVERFLOW When a hardware counter overflows an - * interrupt will be generated which is - * first handled by SIRQ which generates a - * this event. The event increments the - * upper 32 bit of the 64 bit counter. - * SK_PNMI_EVT_SEN_XXX The event is generated by the I2C module - * when a sensor reports a warning or - * error. The event will store a trap - * message in the trap buffer. - * SK_PNMI_EVT_CHG_EST_TIMER The timer event was initiated by this - * module and is used to calculate the - * port switches per hour. - * SK_PNMI_EVT_CLEAR_COUNTER The event clears all counters and - * timestamps. - * SK_PNMI_EVT_XMAC_RESET The event is generated by the driver - * before a hard reset of the XMAC is - * performed. All counters will be saved - * and added to the hardware counter - * values after reset to grant continuous - * counter values. - * SK_PNMI_EVT_RLMT_PORT_UP Generated by RLMT to notify that a port - * went logically up. A trap message will - * be stored to the trap buffer. - * SK_PNMI_EVT_RLMT_PORT_DOWN Generated by RLMT to notify that a port - * went logically down. A trap message will - * be stored to the trap buffer. - * SK_PNMI_EVT_RLMT_SEGMENTATION Generated by RLMT to notify that two - * spanning tree root bridges were - * detected. A trap message will be stored - * to the trap buffer. - * SK_PNMI_EVT_RLMT_ACTIVE_DOWN Notifies PNMI that an active port went - * down. PNMI will not further add the - * statistic values to the virtual port. - * SK_PNMI_EVT_RLMT_ACTIVE_UP Notifies PNMI that a port went up and - * is now an active port. PNMI will now - * add the statistic data of this port to - * the virtual port. - * SK_PNMI_EVT_RLMT_SET_NETS Notifies PNMI about the net mode. The first parameter - * contains the number of nets. 1 means single net, 2 means - * dual net. The second parameter is -1 - * - * Returns: - * Always 0 - */ -int SkPnmiEvent( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -SK_U32 Event, /* Event-Id */ -SK_EVPARA Param) /* Event dependent parameter */ -{ - unsigned int PhysPortIndex; - unsigned int MaxNetNumber; - int CounterIndex; - int Ret; - SK_U16 MacStatus; - SK_U64 OverflowStatus; - SK_U64 Mask; - int MacType; - SK_U64 Value; - SK_U32 Val32; - SK_U16 Register; - SK_EVPARA EventParam; - SK_U64 NewestValue; - SK_U64 OldestValue; - SK_U64 Delta; - SK_PNMI_ESTIMATE *pEst; - SK_U32 NetIndex; - SK_GEPORT *pPrt; - SK_PNMI_VCT *pVctBackupData; - SK_U32 RetCode; - int i; - SK_U32 CableLength; - - -#ifdef DEBUG - if (Event != SK_PNMI_EVT_XMAC_RESET) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: SkPnmiEvent: Called, Event=0x%x, Param=0x%x\n", - (unsigned int)Event, (unsigned int)Param.Para64)); - } -#endif /* DEBUG */ - SK_PNMI_CHECKFLAGS("SkPnmiEvent: On call"); - - MacType = pAC->GIni.GIMacType; - - switch (Event) { - - case SK_PNMI_EVT_SIRQ_OVERFLOW: - PhysPortIndex = (int)Param.Para32[0]; - MacStatus = (SK_U16)Param.Para32[1]; -#ifdef DEBUG - if (PhysPortIndex >= SK_MAX_MACS) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_SIRQ_OVERFLOW parameter" - " wrong, PhysPortIndex=0x%x\n", - PhysPortIndex)); - return (0); - } -#endif /* DEBUG */ - OverflowStatus = 0; - - /* - * Check which source caused an overflow interrupt. - */ - if ((pAC->GIni.GIFunc.pFnMacOverflow(pAC, IoC, PhysPortIndex, - MacStatus, &OverflowStatus) != 0) || - (OverflowStatus == 0)) { - - SK_PNMI_CHECKFLAGS("SkPnmiEvent: On return"); - return (0); - } - - /* - * Check the overflow status register and increment - * the upper dword of corresponding counter. - */ - for (CounterIndex = 0; CounterIndex < sizeof(Mask) * 8; - CounterIndex ++) { - - Mask = (SK_U64)1 << CounterIndex; - if ((OverflowStatus & Mask) == 0) { - - continue; - } - - switch (StatOvrflwBit[CounterIndex][MacType]) { - - case SK_PNMI_HTX_UTILUNDER: - case SK_PNMI_HTX_UTILOVER: - if (MacType == SK_MAC_XMAC) { - XM_IN16(IoC, PhysPortIndex, XM_TX_CMD, &Register); - Register |= XM_TX_SAM_LINE; - XM_OUT16(IoC, PhysPortIndex, XM_TX_CMD, Register); - } - break; - - case SK_PNMI_HRX_UTILUNDER: - case SK_PNMI_HRX_UTILOVER: - if (MacType == SK_MAC_XMAC) { - XM_IN16(IoC, PhysPortIndex, XM_RX_CMD, &Register); - Register |= XM_RX_SAM_LINE; - XM_OUT16(IoC, PhysPortIndex, XM_RX_CMD, Register); - } - break; - - case SK_PNMI_HTX_OCTETHIGH: - case SK_PNMI_HTX_OCTETLOW: - case SK_PNMI_HTX_RESERVED: - case SK_PNMI_HRX_OCTETHIGH: - case SK_PNMI_HRX_OCTETLOW: - case SK_PNMI_HRX_IRLENGTH: - case SK_PNMI_HRX_RESERVED: - - /* - * the following counters aren't be handled (id > 63) - */ - case SK_PNMI_HTX_SYNC: - case SK_PNMI_HTX_SYNC_OCTET: - break; - - case SK_PNMI_HRX_LONGFRAMES: - if (MacType == SK_MAC_GMAC) { - pAC->Pnmi.Port[PhysPortIndex]. - CounterHigh[CounterIndex] ++; - } - break; - - default: - pAC->Pnmi.Port[PhysPortIndex]. - CounterHigh[CounterIndex] ++; - } - } - break; - - case SK_PNMI_EVT_SEN_WAR_LOW: -#ifdef DEBUG - if ((unsigned int)Param.Para64 >= (unsigned int)pAC->I2c.MaxSens) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_SEN_WAR_LOW parameter wrong, SensorIndex=%d\n", - (unsigned int)Param.Para64)); - return (0); - } -#endif /* DEBUG */ - - /* - * Store a trap message in the trap buffer and generate - * an event for user space applications with the - * SK_DRIVER_SENDEVENT macro. - */ - QueueSensorTrap(pAC, OID_SKGE_TRAP_SEN_WAR_LOW, - (unsigned int)Param.Para64); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - break; - - case SK_PNMI_EVT_SEN_WAR_UPP: -#ifdef DEBUG - if ((unsigned int)Param.Para64 >= (unsigned int)pAC->I2c.MaxSens) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_SEN_WAR_UPP parameter wrong, SensorIndex=%d\n", - (unsigned int)Param.Para64)); - return (0); - } -#endif /* DEBUG */ - - /* - * Store a trap message in the trap buffer and generate - * an event for user space applications with the - * SK_DRIVER_SENDEVENT macro. - */ - QueueSensorTrap(pAC, OID_SKGE_TRAP_SEN_WAR_UPP, - (unsigned int)Param.Para64); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - break; - - case SK_PNMI_EVT_SEN_ERR_LOW: -#ifdef DEBUG - if ((unsigned int)Param.Para64 >= (unsigned int)pAC->I2c.MaxSens) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_SEN_ERR_LOW parameter wrong, SensorIndex=%d\n", - (unsigned int)Param.Para64)); - return (0); - } -#endif /* DEBUG */ - - /* - * Store a trap message in the trap buffer and generate - * an event for user space applications with the - * SK_DRIVER_SENDEVENT macro. - */ - QueueSensorTrap(pAC, OID_SKGE_TRAP_SEN_ERR_LOW, - (unsigned int)Param.Para64); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - break; - - case SK_PNMI_EVT_SEN_ERR_UPP: -#ifdef DEBUG - if ((unsigned int)Param.Para64 >= (unsigned int)pAC->I2c.MaxSens) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_SEN_ERR_UPP parameter wrong, SensorIndex=%d\n", - (unsigned int)Param.Para64)); - return (0); - } -#endif /* DEBUG */ - - /* - * Store a trap message in the trap buffer and generate - * an event for user space applications with the - * SK_DRIVER_SENDEVENT macro. - */ - QueueSensorTrap(pAC, OID_SKGE_TRAP_SEN_ERR_UPP, - (unsigned int)Param.Para64); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - break; - - case SK_PNMI_EVT_CHG_EST_TIMER: - /* - * Calculate port switch average on a per hour basis - * Time interval for check : 28125 ms - * Number of values for average : 8 - * - * Be careful in changing these values, on change check - * - typedef of SK_PNMI_ESTIMATE (Size of EstValue - * array one less than value number) - * - Timer initialization SkTimerStart() in SkPnmiInit - * - Delta value below must be multiplicated with - * power of 2 - * - */ - pEst = &pAC->Pnmi.RlmtChangeEstimate; - CounterIndex = pEst->EstValueIndex + 1; - if (CounterIndex == 7) { - - CounterIndex = 0; - } - pEst->EstValueIndex = CounterIndex; - - NewestValue = pAC->Pnmi.RlmtChangeCts; - OldestValue = pEst->EstValue[CounterIndex]; - pEst->EstValue[CounterIndex] = NewestValue; - - /* - * Calculate average. Delta stores the number of - * port switches per 28125 * 8 = 225000 ms - */ - if (NewestValue >= OldestValue) { - - Delta = NewestValue - OldestValue; - } - else { - /* Overflow situation */ - Delta = (SK_U64)(0 - OldestValue) + NewestValue; - } - - /* - * Extrapolate delta to port switches per hour. - * Estimate = Delta * (3600000 / 225000) - * = Delta * 16 - * = Delta << 4 - */ - pAC->Pnmi.RlmtChangeEstimate.Estimate = Delta << 4; - - /* - * Check if threshold is exceeded. If the threshold is - * permanently exceeded every 28125 ms an event will be - * generated to remind the user of this condition. - */ - if ((pAC->Pnmi.RlmtChangeThreshold != 0) && - (pAC->Pnmi.RlmtChangeEstimate.Estimate >= - pAC->Pnmi.RlmtChangeThreshold)) { - - QueueSimpleTrap(pAC, OID_SKGE_TRAP_RLMT_CHANGE_THRES); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - } - - SK_MEMSET((char *)&EventParam, 0, sizeof(EventParam)); - SkTimerStart(pAC, IoC, &pAC->Pnmi.RlmtChangeEstimate.EstTimer, - 28125000, SKGE_PNMI, SK_PNMI_EVT_CHG_EST_TIMER, - EventParam); - break; - - case SK_PNMI_EVT_CLEAR_COUNTER: - /* - * Param.Para32[0] contains the NetIndex (0 ..1). - * Param.Para32[1] is reserved, contains -1. - */ - NetIndex = (SK_U32)Param.Para32[0]; - -#ifdef DEBUG - if (NetIndex >= pAC->Rlmt.NumNets) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_CLEAR_COUNTER parameter wrong, NetIndex=%d\n", - NetIndex)); - - return (0); - } -#endif /* DEBUG */ - - /* - * Set all counters and timestamps to zero. - * The according NetIndex is required as a - * parameter of the event. - */ - ResetCounter(pAC, IoC, NetIndex); - break; - - case SK_PNMI_EVT_XMAC_RESET: - /* - * To grant continuous counter values store the current - * XMAC statistic values to the entries 1..n of the - * CounterOffset array. XMAC Errata #2 - */ -#ifdef DEBUG - if ((unsigned int)Param.Para64 >= SK_MAX_MACS) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_XMAC_RESET parameter wrong, PhysPortIndex=%d\n", - (unsigned int)Param.Para64)); - return (0); - } -#endif - PhysPortIndex = (unsigned int)Param.Para64; - - /* - * Update XMAC statistic to get fresh values - */ - Ret = MacUpdate(pAC, IoC, 0, pAC->GIni.GIMacsFound - 1); - if (Ret != SK_PNMI_ERR_OK) { - - SK_PNMI_CHECKFLAGS("SkPnmiEvent: On return"); - return (0); - } - /* - * Increment semaphore to indicate that an update was - * already done - */ - pAC->Pnmi.MacUpdatedFlag ++; - - for (CounterIndex = 0; CounterIndex < SK_PNMI_MAX_IDX; - CounterIndex ++) { - - if (!StatAddr[CounterIndex][MacType].GetOffset) { - - continue; - } - - pAC->Pnmi.Port[PhysPortIndex].CounterOffset[CounterIndex] = - GetPhysStatVal(pAC, IoC, PhysPortIndex, CounterIndex); - - pAC->Pnmi.Port[PhysPortIndex].CounterHigh[CounterIndex] = 0; - } - - pAC->Pnmi.MacUpdatedFlag --; - break; - - case SK_PNMI_EVT_RLMT_PORT_UP: - PhysPortIndex = (unsigned int)Param.Para32[0]; -#ifdef DEBUG - if (PhysPortIndex >= SK_MAX_MACS) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_RLMT_PORT_UP parameter" - " wrong, PhysPortIndex=%d\n", PhysPortIndex)); - - return (0); - } -#endif /* DEBUG */ - - /* - * Store a trap message in the trap buffer and generate an event for - * user space applications with the SK_DRIVER_SENDEVENT macro. - */ - QueueRlmtPortTrap(pAC, OID_SKGE_TRAP_RLMT_PORT_UP, PhysPortIndex); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - - /* Bugfix for XMAC errata (#10620)*/ - if (MacType == SK_MAC_XMAC) { - /* Add incremental difference to offset (#10620)*/ - (void)pAC->GIni.GIFunc.pFnMacStatistic(pAC, IoC, PhysPortIndex, - XM_RXE_SHT_ERR, &Val32); - - Value = (((SK_U64)pAC->Pnmi.Port[PhysPortIndex]. - CounterHigh[SK_PNMI_HRX_SHORTS] << 32) | (SK_U64)Val32); - pAC->Pnmi.Port[PhysPortIndex].CounterOffset[SK_PNMI_HRX_SHORTS] += - Value - pAC->Pnmi.Port[PhysPortIndex].RxShortZeroMark; - } - - /* Tell VctStatus() that a link was up meanwhile. */ - pAC->Pnmi.VctStatus[PhysPortIndex] |= SK_PNMI_VCT_LINK; - break; - - case SK_PNMI_EVT_RLMT_PORT_DOWN: - PhysPortIndex = (unsigned int)Param.Para32[0]; - -#ifdef DEBUG - if (PhysPortIndex >= SK_MAX_MACS) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_RLMT_PORT_DOWN parameter" - " wrong, PhysPortIndex=%d\n", PhysPortIndex)); - - return (0); - } -#endif /* DEBUG */ - - /* - * Store a trap message in the trap buffer and generate an event for - * user space applications with the SK_DRIVER_SENDEVENT macro. - */ - QueueRlmtPortTrap(pAC, OID_SKGE_TRAP_RLMT_PORT_DOWN, PhysPortIndex); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - - /* Bugfix #10620 - get zero level for incremental difference */ - if (MacType == SK_MAC_XMAC) { - - (void)pAC->GIni.GIFunc.pFnMacStatistic(pAC, IoC, PhysPortIndex, - XM_RXE_SHT_ERR, &Val32); - - pAC->Pnmi.Port[PhysPortIndex].RxShortZeroMark = - (((SK_U64)pAC->Pnmi.Port[PhysPortIndex]. - CounterHigh[SK_PNMI_HRX_SHORTS] << 32) | (SK_U64)Val32); - } - break; - - case SK_PNMI_EVT_RLMT_ACTIVE_DOWN: - PhysPortIndex = (unsigned int)Param.Para32[0]; - NetIndex = (SK_U32)Param.Para32[1]; - -#ifdef DEBUG - if (PhysPortIndex >= SK_MAX_MACS) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_RLMT_ACTIVE_DOWN parameter too high, PhysPort=%d\n", - PhysPortIndex)); - } - - if (NetIndex >= pAC->Rlmt.NumNets) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_RLMT_ACTIVE_DOWN parameter too high, NetIndex=%d\n", - NetIndex)); - } -#endif /* DEBUG */ - - /* - * For now, ignore event if NetIndex != 0. - */ - if (Param.Para32[1] != 0) { - - return (0); - } - - /* - * Nothing to do if port is already inactive - */ - if (!pAC->Pnmi.Port[PhysPortIndex].ActiveFlag) { - - return (0); - } - - /* - * Update statistic counters to calculate new offset for the virtual - * port and increment semaphore to indicate that an update was already - * done. - */ - if (MacUpdate(pAC, IoC, 0, pAC->GIni.GIMacsFound - 1) != - SK_PNMI_ERR_OK) { - - SK_PNMI_CHECKFLAGS("SkPnmiEvent: On return"); - return (0); - } - pAC->Pnmi.MacUpdatedFlag ++; - - /* - * Calculate new counter offset for virtual port to grant continous - * counting on port switches. The virtual port consists of all currently - * active ports. The port down event indicates that a port is removed - * from the virtual port. Therefore add the counter value of the removed - * port to the CounterOffset for the virtual port to grant the same - * counter value. - */ - for (CounterIndex = 0; CounterIndex < SK_PNMI_MAX_IDX; - CounterIndex ++) { - - if (!StatAddr[CounterIndex][MacType].GetOffset) { - - continue; - } - - Value = GetPhysStatVal(pAC, IoC, PhysPortIndex, CounterIndex); - - pAC->Pnmi.VirtualCounterOffset[CounterIndex] += Value; - } - - /* - * Set port to inactive - */ - pAC->Pnmi.Port[PhysPortIndex].ActiveFlag = SK_FALSE; - - pAC->Pnmi.MacUpdatedFlag --; - break; - - case SK_PNMI_EVT_RLMT_ACTIVE_UP: - PhysPortIndex = (unsigned int)Param.Para32[0]; - NetIndex = (SK_U32)Param.Para32[1]; - -#ifdef DEBUG - if (PhysPortIndex >= SK_MAX_MACS) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_RLMT_ACTIVE_UP parameter too high, PhysPort=%d\n", - PhysPortIndex)); - } - - if (NetIndex >= pAC->Rlmt.NumNets) { - - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_CTRL, - ("PNMI: ERR: SkPnmiEvent: SK_PNMI_EVT_RLMT_ACTIVE_UP parameter too high, NetIndex=%d\n", - NetIndex)); - } -#endif /* DEBUG */ - - /* - * For now, ignore event if NetIndex != 0. - */ - if (Param.Para32[1] != 0) { - - return (0); - } - - /* - * Nothing to do if port is already active - */ - if (pAC->Pnmi.Port[PhysPortIndex].ActiveFlag) { - - return (0); - } - - /* - * Statistic maintenance - */ - pAC->Pnmi.RlmtChangeCts ++; - pAC->Pnmi.RlmtChangeTime = SK_PNMI_HUNDREDS_SEC(SkOsGetTime(pAC)); - - /* - * Store a trap message in the trap buffer and generate an event for - * user space applications with the SK_DRIVER_SENDEVENT macro. - */ - QueueRlmtNewMacTrap(pAC, PhysPortIndex); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - - /* - * Update statistic counters to calculate new offset for the virtual - * port and increment semaphore to indicate that an update was - * already done. - */ - if (MacUpdate(pAC, IoC, 0, pAC->GIni.GIMacsFound - 1) != - SK_PNMI_ERR_OK) { - - SK_PNMI_CHECKFLAGS("SkPnmiEvent: On return"); - return (0); - } - pAC->Pnmi.MacUpdatedFlag ++; - - /* - * Calculate new counter offset for virtual port to grant continous - * counting on port switches. A new port is added to the virtual port. - * Therefore substract the counter value of the new port from the - * CounterOffset for the virtual port to grant the same value. - */ - for (CounterIndex = 0; CounterIndex < SK_PNMI_MAX_IDX; - CounterIndex ++) { - - if (!StatAddr[CounterIndex][MacType].GetOffset) { - - continue; - } - - Value = GetPhysStatVal(pAC, IoC, PhysPortIndex, CounterIndex); - - pAC->Pnmi.VirtualCounterOffset[CounterIndex] -= Value; - } - - /* Set port to active */ - pAC->Pnmi.Port[PhysPortIndex].ActiveFlag = SK_TRUE; - - pAC->Pnmi.MacUpdatedFlag --; - break; - - case SK_PNMI_EVT_RLMT_SEGMENTATION: - /* - * Para.Para32[0] contains the NetIndex. - */ - - /* - * Store a trap message in the trap buffer and generate an event for - * user space applications with the SK_DRIVER_SENDEVENT macro. - */ - QueueSimpleTrap(pAC, OID_SKGE_TRAP_RLMT_SEGMENTATION); - (void)SK_DRIVER_SENDEVENT(pAC, IoC); - break; - - case SK_PNMI_EVT_RLMT_SET_NETS: - /* - * Param.Para32[0] contains the number of Nets. - * Param.Para32[1] is reserved, contains -1. - */ - /* - * Check number of nets - */ - MaxNetNumber = pAC->GIni.GIMacsFound; - if (((unsigned int)Param.Para32[0] < 1) - || ((unsigned int)Param.Para32[0] > MaxNetNumber)) { - return (SK_PNMI_ERR_UNKNOWN_NET); - } - - if ((unsigned int)Param.Para32[0] == 1) { /* single net mode */ - pAC->Pnmi.DualNetActiveFlag = SK_FALSE; - } - else { /* dual net mode */ - pAC->Pnmi.DualNetActiveFlag = SK_TRUE; - } - break; - - case SK_PNMI_EVT_VCT_RESET: - PhysPortIndex = Param.Para32[0]; - pPrt = &pAC->GIni.GP[PhysPortIndex]; - pVctBackupData = &pAC->Pnmi.VctBackup[PhysPortIndex]; - - if (pAC->Pnmi.VctStatus[PhysPortIndex] & SK_PNMI_VCT_PENDING) { - RetCode = SkGmCableDiagStatus(pAC, IoC, PhysPortIndex, SK_FALSE); - if (RetCode == 2) { - /* - * VCT test is still running. - * Start VCT timer counter again. - */ - SK_MEMSET((char *) &Param, 0, sizeof(Param)); - Param.Para32[0] = PhysPortIndex; - Param.Para32[1] = -1; - SkTimerStart(pAC, IoC, - &pAC->Pnmi.VctTimeout[PhysPortIndex].VctTimer, - 4000000, SKGE_PNMI, SK_PNMI_EVT_VCT_RESET, Param); - break; - } - pAC->Pnmi.VctStatus[PhysPortIndex] &= ~SK_PNMI_VCT_PENDING; - pAC->Pnmi.VctStatus[PhysPortIndex] |= - (SK_PNMI_VCT_NEW_VCT_DATA | SK_PNMI_VCT_TEST_DONE); - - /* Copy results for later use to PNMI struct. */ - for (i = 0; i < 4; i++) { - if (pPrt->PMdiPairSts[i] == SK_PNMI_VCT_NORMAL_CABLE) { - if ((pPrt->PMdiPairLen[i] > 35) && - (pPrt->PMdiPairLen[i] < 0xff)) { - pPrt->PMdiPairSts[i] = SK_PNMI_VCT_IMPEDANCE_MISMATCH; - } - } - if ((pPrt->PMdiPairLen[i] > 35) && - (pPrt->PMdiPairLen[i] != 0xff)) { - CableLength = 1000 * - (((175 * pPrt->PMdiPairLen[i]) / 210) - 28); - } - else { - CableLength = 0; - } - pVctBackupData->PMdiPairLen[i] = CableLength; - pVctBackupData->PMdiPairSts[i] = pPrt->PMdiPairSts[i]; - } - - Param.Para32[0] = PhysPortIndex; - Param.Para32[1] = -1; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_RESET, Param); - SkEventDispatcher(pAC, IoC); - } - - break; - - default: - break; - } - - SK_PNMI_CHECKFLAGS("SkPnmiEvent: On return"); - return (0); -} - - -/****************************************************************************** - * - * Private functions - * - */ - -/***************************************************************************** - * - * PnmiVar - Gets, presets, and sets single OIDs - * - * Description: - * Looks up the requested OID, calls the corresponding handler - * function, and passes the parameters with the get, preset, or - * set command. The function is called by SkGePnmiGetVar, - * SkGePnmiPreSetVar, or SkGePnmiSetVar. - * - * Returns: - * SK_PNMI_ERR_XXX. For details have a look at the description of the - * calling functions. - * SK_PNMI_ERR_UNKNOWN_NET The requested NetIndex doesn't exist - */ -PNMI_STATIC int PnmiVar( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* Total length of pBuf management data */ -SK_U32 Instance, /* Instance (1..n) that is to be set or -1 */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - unsigned int TableIndex; - int Ret; - - - if ((TableIndex = LookupId(Id)) == (unsigned int)(-1)) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_OID); - } - - /* Check NetIndex */ - if (NetIndex >= pAC->Rlmt.NumNets) { - return (SK_PNMI_ERR_UNKNOWN_NET); - } - - SK_PNMI_CHECKFLAGS("PnmiVar: On call"); - - Ret = IdTable[TableIndex].Func(pAC, IoC, Action, Id, pBuf, pLen, - Instance, TableIndex, NetIndex); - - SK_PNMI_CHECKFLAGS("PnmiVar: On return"); - - return (Ret); -} - -/***************************************************************************** - * - * PnmiStruct - Presets and Sets data in structure SK_PNMI_STRUCT_DATA - * - * Description: - * The return value of the function will also be stored in - * SK_PNMI_STRUCT_DATA if the passed buffer has the minimum size of - * SK_PNMI_MIN_STRUCT_SIZE. The sub-function runs through the IdTable, - * checks which OIDs are able to set, and calls the handler function of - * the OID to perform the set. The return value of the function will - * also be stored in SK_PNMI_STRUCT_DATA if the passed buffer has the - * minimum size of SK_PNMI_MIN_STRUCT_SIZE. The function is called - * by SkGePnmiPreSetStruct and SkGePnmiSetStruct. - * - * Returns: - * SK_PNMI_ERR_XXX. The codes are described in the calling functions. - * SK_PNMI_ERR_UNKNOWN_NET The requested NetIndex doesn't exist - */ -PNMI_STATIC int PnmiStruct( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* PRESET/SET action to be performed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* Length of pBuf management data buffer */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - int Ret; - unsigned int TableIndex; - unsigned int DstOffset; - unsigned int Len; - unsigned int InstanceNo; - unsigned int InstanceCnt; - SK_U32 Instance; - SK_U32 Id; - - - /* Check if the passed buffer has the right size */ - if (*pLen < SK_PNMI_STRUCT_SIZE) { - - /* Check if we can return the error within the buffer */ - if (*pLen >= SK_PNMI_MIN_STRUCT_SIZE) { - - SK_PNMI_SET_STAT(pBuf, SK_PNMI_ERR_TOO_SHORT, - (SK_U32)(-1)); - } - - *pLen = SK_PNMI_STRUCT_SIZE; - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* Check NetIndex */ - if (NetIndex >= pAC->Rlmt.NumNets) { - return (SK_PNMI_ERR_UNKNOWN_NET); - } - - SK_PNMI_CHECKFLAGS("PnmiStruct: On call"); - - /* - * Update the values of RLMT and SIRQ and increment semaphores to - * indicate that an update was already done. - */ - if ((Ret = RlmtUpdate(pAC, IoC, NetIndex)) != SK_PNMI_ERR_OK) { - - SK_PNMI_SET_STAT(pBuf, Ret, (SK_U32)(-1)); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (Ret); - } - - if ((Ret = SirqUpdate(pAC, IoC)) != SK_PNMI_ERR_OK) { - - SK_PNMI_SET_STAT(pBuf, Ret, (SK_U32)(-1)); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (Ret); - } - - pAC->Pnmi.RlmtUpdatedFlag ++; - pAC->Pnmi.SirqUpdatedFlag ++; - - /* Preset/Set values */ - for (TableIndex = 0; TableIndex < ID_TABLE_SIZE; TableIndex ++) { - - if ((IdTable[TableIndex].Access != SK_PNMI_RW) && - (IdTable[TableIndex].Access != SK_PNMI_WO)) { - - continue; - } - - InstanceNo = IdTable[TableIndex].InstanceNo; - Id = IdTable[TableIndex].Id; - - for (InstanceCnt = 1; InstanceCnt <= InstanceNo; - InstanceCnt ++) { - - DstOffset = IdTable[TableIndex].Offset + - (InstanceCnt - 1) * - IdTable[TableIndex].StructSize; - - /* - * Because VPD multiple instance variables are - * not setable we do not need to evaluate VPD - * instances. Have a look to VPD instance - * calculation in SkPnmiGetStruct(). - */ - Instance = (SK_U32)InstanceCnt; - - /* - * Evaluate needed buffer length - */ - Len = 0; - Ret = IdTable[TableIndex].Func(pAC, IoC, - SK_PNMI_GET, IdTable[TableIndex].Id, - NULL, &Len, Instance, TableIndex, NetIndex); - - if (Ret == SK_PNMI_ERR_UNKNOWN_INST) { - - break; - } - if (Ret != SK_PNMI_ERR_TOO_SHORT) { - - pAC->Pnmi.RlmtUpdatedFlag --; - pAC->Pnmi.SirqUpdatedFlag --; - - SK_PNMI_CHECKFLAGS("PnmiStruct: On return"); - SK_PNMI_SET_STAT(pBuf, - SK_PNMI_ERR_GENERAL, DstOffset); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (SK_PNMI_ERR_GENERAL); - } - if (Id == OID_SKGE_VPD_ACTION) { - - switch (*(pBuf + DstOffset)) { - - case SK_PNMI_VPD_CREATE: - Len = 3 + *(pBuf + DstOffset + 3); - break; - - case SK_PNMI_VPD_DELETE: - Len = 3; - break; - - default: - Len = 1; - break; - } - } - - /* Call the OID handler function */ - Ret = IdTable[TableIndex].Func(pAC, IoC, Action, - IdTable[TableIndex].Id, pBuf + DstOffset, - &Len, Instance, TableIndex, NetIndex); - - if (Ret != SK_PNMI_ERR_OK) { - - pAC->Pnmi.RlmtUpdatedFlag --; - pAC->Pnmi.SirqUpdatedFlag --; - - SK_PNMI_CHECKFLAGS("PnmiStruct: On return"); - SK_PNMI_SET_STAT(pBuf, SK_PNMI_ERR_BAD_VALUE, - DstOffset); - *pLen = SK_PNMI_MIN_STRUCT_SIZE; - return (SK_PNMI_ERR_BAD_VALUE); - } - } - } - - pAC->Pnmi.RlmtUpdatedFlag --; - pAC->Pnmi.SirqUpdatedFlag --; - - SK_PNMI_CHECKFLAGS("PnmiStruct: On return"); - SK_PNMI_SET_STAT(pBuf, SK_PNMI_ERR_OK, (SK_U32)(-1)); - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * LookupId - Lookup an OID in the IdTable - * - * Description: - * Scans the IdTable to find the table entry of an OID. - * - * Returns: - * The table index or -1 if not found. - */ -PNMI_STATIC int LookupId( -SK_U32 Id) /* Object identifier to be searched */ -{ - int i; - - for (i = 0; i < ID_TABLE_SIZE; i++) { - - if (IdTable[i].Id == Id) { - - return i; - } - } - - return (-1); -} - -/***************************************************************************** - * - * OidStruct - Handler of OID_SKGE_ALL_DATA - * - * Description: - * This OID performs a Get/Preset/SetStruct call and returns all data - * in a SK_PNMI_STRUCT_DATA structure. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int OidStruct( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - if (Id != OID_SKGE_ALL_DATA) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR003, - SK_PNMI_ERR003MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* - * Check instance. We only handle single instance variables - */ - if (Instance != (SK_U32)(-1) && Instance != 1) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - switch (Action) { - - case SK_PNMI_GET: - return (SkPnmiGetStruct(pAC, IoC, pBuf, pLen, NetIndex)); - - case SK_PNMI_PRESET: - return (SkPnmiPreSetStruct(pAC, IoC, pBuf, pLen, NetIndex)); - - case SK_PNMI_SET: - return (SkPnmiSetStruct(pAC, IoC, pBuf, pLen, NetIndex)); - } - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR004, SK_PNMI_ERR004MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); -} - -/***************************************************************************** - * - * Perform - OID handler of OID_SKGE_ACTION - * - * Description: - * None. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int Perform( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - int Ret; - SK_U32 ActionOp; - - - /* - * Check instance. We only handle single instance variables - */ - if (Instance != (SK_U32)(-1) && Instance != 1) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - if (*pLen < sizeof(SK_U32)) { - - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* Check if a get should be performed */ - if (Action == SK_PNMI_GET) { - - /* A get is easy. We always return the same value */ - ActionOp = (SK_U32)SK_PNMI_ACT_IDLE; - SK_PNMI_STORE_U32(pBuf, ActionOp); - *pLen = sizeof(SK_U32); - - return (SK_PNMI_ERR_OK); - } - - /* Continue with PRESET/SET action */ - if (*pLen > sizeof(SK_U32)) { - - return (SK_PNMI_ERR_BAD_VALUE); - } - - /* Check if the command is a known one */ - SK_PNMI_READ_U32(pBuf, ActionOp); - if (*pLen > sizeof(SK_U32) || - (ActionOp != SK_PNMI_ACT_IDLE && - ActionOp != SK_PNMI_ACT_RESET && - ActionOp != SK_PNMI_ACT_SELFTEST && - ActionOp != SK_PNMI_ACT_RESETCNT)) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - /* A preset ends here */ - if (Action == SK_PNMI_PRESET) { - - return (SK_PNMI_ERR_OK); - } - - switch (ActionOp) { - - case SK_PNMI_ACT_IDLE: - /* Nothing to do */ - break; - - case SK_PNMI_ACT_RESET: - /* - * Perform a driver reset or something that comes near - * to this. - */ - Ret = SK_DRIVER_RESET(pAC, IoC); - if (Ret != 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR005, - SK_PNMI_ERR005MSG); - - return (SK_PNMI_ERR_GENERAL); - } - break; - - case SK_PNMI_ACT_SELFTEST: - /* - * Perform a driver selftest or something similar to this. - * Currently this feature is not used and will probably - * implemented in another way. - */ - Ret = SK_DRIVER_SELFTEST(pAC, IoC); - pAC->Pnmi.TestResult = Ret; - break; - - case SK_PNMI_ACT_RESETCNT: - /* Set all counters and timestamps to zero */ - ResetCounter(pAC, IoC, NetIndex); - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR006, - SK_PNMI_ERR006MSG); - - return (SK_PNMI_ERR_GENERAL); - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * Mac8023Stat - OID handler of OID_GEN_XXX and OID_802_3_XXX - * - * Description: - * Retrieves the statistic values of the virtual port (logical - * index 0). Only special OIDs of NDIS are handled which consist - * of a 32 bit instead of a 64 bit value. The OIDs are public - * because perhaps some other platform can use them too. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int Mac8023Stat( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - int Ret; - SK_U64 StatVal; - SK_U32 StatVal32; - SK_BOOL Is64BitReq = SK_FALSE; - - /* - * Only the active Mac is returned - */ - if (Instance != (SK_U32)(-1) && Instance != 1) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - /* - * Check action type - */ - if (Action != SK_PNMI_GET) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - /* Check length */ - switch (Id) { - - case OID_802_3_PERMANENT_ADDRESS: - case OID_802_3_CURRENT_ADDRESS: - if (*pLen < sizeof(SK_MAC_ADDR)) { - - *pLen = sizeof(SK_MAC_ADDR); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: -#ifndef SK_NDIS_64BIT_CTR - if (*pLen < sizeof(SK_U32)) { - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - -#else /* SK_NDIS_64BIT_CTR */ - - /* for compatibility, at least 32bit are required for OID */ - if (*pLen < sizeof(SK_U32)) { - /* - * but indicate handling for 64bit values, - * if insufficient space is provided - */ - *pLen = sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - - Is64BitReq = (*pLen < sizeof(SK_U64)) ? SK_FALSE : SK_TRUE; -#endif /* SK_NDIS_64BIT_CTR */ - break; - } - - /* - * Update all statistics, because we retrieve virtual MAC, which - * consists of multiple physical statistics and increment semaphore - * to indicate that an update was already done. - */ - Ret = MacUpdate(pAC, IoC, 0, pAC->GIni.GIMacsFound - 1); - if ( Ret != SK_PNMI_ERR_OK) { - - *pLen = 0; - return (Ret); - } - pAC->Pnmi.MacUpdatedFlag ++; - - /* - * Get value (MAC Index 0 identifies the virtual MAC) - */ - switch (Id) { - - case OID_802_3_PERMANENT_ADDRESS: - CopyMac(pBuf, &pAC->Addr.Net[NetIndex].PermanentMacAddress); - *pLen = sizeof(SK_MAC_ADDR); - break; - - case OID_802_3_CURRENT_ADDRESS: - CopyMac(pBuf, &pAC->Addr.Net[NetIndex].CurrentMacAddress); - *pLen = sizeof(SK_MAC_ADDR); - break; - - default: - StatVal = GetStatVal(pAC, IoC, 0, IdTable[TableIndex].Param, NetIndex); - - /* by default 32bit values are evaluated */ - if (!Is64BitReq) { - StatVal32 = (SK_U32)StatVal; - SK_PNMI_STORE_U32(pBuf, StatVal32); - *pLen = sizeof(SK_U32); - } - else { - SK_PNMI_STORE_U64(pBuf, StatVal); - *pLen = sizeof(SK_U64); - } - break; - } - - pAC->Pnmi.MacUpdatedFlag --; - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * MacPrivateStat - OID handler function of OID_SKGE_STAT_XXX - * - * Description: - * Retrieves the MAC statistic data. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int MacPrivateStat( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - unsigned int LogPortMax; - unsigned int LogPortIndex; - unsigned int PhysPortMax; - unsigned int Limit; - unsigned int Offset; - int MacType; - int Ret; - SK_U64 StatVal; - - - - /* Calculate instance if wished. MAC index 0 is the virtual MAC */ - PhysPortMax = pAC->GIni.GIMacsFound; - LogPortMax = SK_PNMI_PORT_PHYS2LOG(PhysPortMax); - - MacType = pAC->GIni.GIMacType; - - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { /* Dual net mode */ - LogPortMax--; - } - - if ((Instance != (SK_U32)(-1))) { /* Only one specific instance is queried */ - /* Check instance range */ - if ((Instance < 1) || (Instance > LogPortMax)) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - LogPortIndex = SK_PNMI_PORT_INST2LOG(Instance); - Limit = LogPortIndex + 1; - } - - else { /* Instance == (SK_U32)(-1), get all Instances of that OID */ - - LogPortIndex = 0; - Limit = LogPortMax; - } - - /* Check action */ - if (Action != SK_PNMI_GET) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - /* Check length */ - if (*pLen < (Limit - LogPortIndex) * sizeof(SK_U64)) { - - *pLen = (Limit - LogPortIndex) * sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* - * Update MAC statistic and increment semaphore to indicate that - * an update was already done. - */ - Ret = MacUpdate(pAC, IoC, 0, pAC->GIni.GIMacsFound - 1); - if (Ret != SK_PNMI_ERR_OK) { - - *pLen = 0; - return (Ret); - } - pAC->Pnmi.MacUpdatedFlag ++; - - /* Get value */ - Offset = 0; - for (; LogPortIndex < Limit; LogPortIndex ++) { - - switch (Id) { - -/* XXX not yet implemented due to XMAC problems - case OID_SKGE_STAT_TX_UTIL: - return (SK_PNMI_ERR_GENERAL); -*/ -/* XXX not yet implemented due to XMAC problems - case OID_SKGE_STAT_RX_UTIL: - return (SK_PNMI_ERR_GENERAL); -*/ - case OID_SKGE_STAT_RX: - if (MacType == SK_MAC_GMAC) { - StatVal = - GetStatVal(pAC, IoC, LogPortIndex, - SK_PNMI_HRX_BROADCAST, NetIndex) + - GetStatVal(pAC, IoC, LogPortIndex, - SK_PNMI_HRX_MULTICAST, NetIndex) + - GetStatVal(pAC, IoC, LogPortIndex, - SK_PNMI_HRX_UNICAST, NetIndex) + - GetStatVal(pAC, IoC, LogPortIndex, - SK_PNMI_HRX_UNDERSIZE, NetIndex); - } - else { - StatVal = GetStatVal(pAC, IoC, LogPortIndex, - IdTable[TableIndex].Param, NetIndex); - } - break; - - case OID_SKGE_STAT_TX: - if (MacType == SK_MAC_GMAC) { - StatVal = - GetStatVal(pAC, IoC, LogPortIndex, - SK_PNMI_HTX_BROADCAST, NetIndex) + - GetStatVal(pAC, IoC, LogPortIndex, - SK_PNMI_HTX_MULTICAST, NetIndex) + - GetStatVal(pAC, IoC, LogPortIndex, - SK_PNMI_HTX_UNICAST, NetIndex); - } - else { - StatVal = GetStatVal(pAC, IoC, LogPortIndex, - IdTable[TableIndex].Param, NetIndex); - } - break; - - default: - StatVal = GetStatVal(pAC, IoC, LogPortIndex, - IdTable[TableIndex].Param, NetIndex); - } - SK_PNMI_STORE_U64(pBuf + Offset, StatVal); - - Offset += sizeof(SK_U64); - } - *pLen = Offset; - - pAC->Pnmi.MacUpdatedFlag --; - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * Addr - OID handler function of OID_SKGE_PHYS_CUR_ADDR and _FAC_ADDR - * - * Description: - * Get/Presets/Sets the current and factory MAC address. The MAC - * address of the virtual port, which is reported to the OS, may - * not be changed, but the physical ones. A set to the virtual port - * will be ignored. No error should be reported because otherwise - * a multiple instance set (-1) would always fail. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int Addr( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - int Ret; - unsigned int LogPortMax; - unsigned int PhysPortMax; - unsigned int LogPortIndex; - unsigned int PhysPortIndex; - unsigned int Limit; - unsigned int Offset = 0; - - /* - * Calculate instance if wished. MAC index 0 is the virtual - * MAC. - */ - PhysPortMax = pAC->GIni.GIMacsFound; - LogPortMax = SK_PNMI_PORT_PHYS2LOG(PhysPortMax); - - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { /* Dual net mode */ - LogPortMax--; - } - - if ((Instance != (SK_U32)(-1))) { /* Only one specific instance is queried */ - /* Check instance range */ - if ((Instance < 1) || (Instance > LogPortMax)) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - LogPortIndex = SK_PNMI_PORT_INST2LOG(Instance); - Limit = LogPortIndex + 1; - } - else { /* Instance == (SK_U32)(-1), get all Instances of that OID */ - - LogPortIndex = 0; - Limit = LogPortMax; - } - - /* - * Perform Action - */ - if (Action == SK_PNMI_GET) { - - /* Check length */ - if (*pLen < (Limit - LogPortIndex) * 6) { - - *pLen = (Limit - LogPortIndex) * 6; - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* - * Get value - */ - for (; LogPortIndex < Limit; LogPortIndex ++) { - - switch (Id) { - - case OID_SKGE_PHYS_CUR_ADDR: - if (LogPortIndex == 0) { - CopyMac(pBuf + Offset, &pAC->Addr.Net[NetIndex].CurrentMacAddress); - } - else { - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS(pAC, LogPortIndex); - - CopyMac(pBuf + Offset, - &pAC->Addr.Port[PhysPortIndex].CurrentMacAddress); - } - Offset += 6; - break; - - case OID_SKGE_PHYS_FAC_ADDR: - if (LogPortIndex == 0) { - CopyMac(pBuf + Offset, - &pAC->Addr.Net[NetIndex].PermanentMacAddress); - } - else { - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - CopyMac(pBuf + Offset, - &pAC->Addr.Port[PhysPortIndex].PermanentMacAddress); - } - Offset += 6; - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR008, - SK_PNMI_ERR008MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - - *pLen = Offset; - } - else { - /* - * The logical MAC address may not be changed only - * the physical ones - */ - if (Id == OID_SKGE_PHYS_FAC_ADDR) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - /* - * Only the current address may be changed - */ - if (Id != OID_SKGE_PHYS_CUR_ADDR) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR009, - SK_PNMI_ERR009MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* Check length */ - if (*pLen < (Limit - LogPortIndex) * 6) { - - *pLen = (Limit - LogPortIndex) * 6; - return (SK_PNMI_ERR_TOO_SHORT); - } - if (*pLen > (Limit - LogPortIndex) * 6) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - /* - * Check Action - */ - if (Action == SK_PNMI_PRESET) { - - *pLen = 0; - return (SK_PNMI_ERR_OK); - } - - /* - * Set OID_SKGE_MAC_CUR_ADDR - */ - for (; LogPortIndex < Limit; LogPortIndex ++, Offset += 6) { - - /* - * A set to virtual port and set of broadcast - * address will be ignored - */ - if (LogPortIndex == 0 || SK_MEMCMP(pBuf + Offset, - "\xff\xff\xff\xff\xff\xff", 6) == 0) { - - continue; - } - - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS(pAC, - LogPortIndex); - - Ret = SkAddrOverride(pAC, IoC, PhysPortIndex, - (SK_MAC_ADDR *)(pBuf + Offset), - (LogPortIndex == 0 ? SK_ADDR_VIRTUAL_ADDRESS : - SK_ADDR_PHYSICAL_ADDRESS)); - if (Ret != SK_ADDR_OVERRIDE_SUCCESS) { - - return (SK_PNMI_ERR_GENERAL); - } - } - *pLen = Offset; - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * CsumStat - OID handler function of OID_SKGE_CHKSM_XXX - * - * Description: - * Retrieves the statistic values of the CSUM module. The CSUM data - * structure must be available in the SK_AC even if the CSUM module - * is not included, because PNMI reads the statistic data from the - * CSUM part of SK_AC directly. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int CsumStat( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - unsigned int Index; - unsigned int Limit; - unsigned int Offset = 0; - SK_U64 StatVal; - - - /* - * Calculate instance if wished - */ - if (Instance != (SK_U32)(-1)) { - - if ((Instance < 1) || (Instance > SKCS_NUM_PROTOCOLS)) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - Index = (unsigned int)Instance - 1; - Limit = Index + 1; - } - else { - Index = 0; - Limit = SKCS_NUM_PROTOCOLS; - } - - /* - * Check action - */ - if (Action != SK_PNMI_GET) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - /* Check length */ - if (*pLen < (Limit - Index) * sizeof(SK_U64)) { - - *pLen = (Limit - Index) * sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* - * Get value - */ - for (; Index < Limit; Index ++) { - - switch (Id) { - - case OID_SKGE_CHKSM_RX_OK_CTS: - StatVal = pAC->Csum.ProtoStats[NetIndex][Index].RxOkCts; - break; - - case OID_SKGE_CHKSM_RX_UNABLE_CTS: - StatVal = pAC->Csum.ProtoStats[NetIndex][Index].RxUnableCts; - break; - - case OID_SKGE_CHKSM_RX_ERR_CTS: - StatVal = pAC->Csum.ProtoStats[NetIndex][Index].RxErrCts; - break; - - case OID_SKGE_CHKSM_TX_OK_CTS: - StatVal = pAC->Csum.ProtoStats[NetIndex][Index].TxOkCts; - break; - - case OID_SKGE_CHKSM_TX_UNABLE_CTS: - StatVal = pAC->Csum.ProtoStats[NetIndex][Index].TxUnableCts; - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR010, - SK_PNMI_ERR010MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - SK_PNMI_STORE_U64(pBuf + Offset, StatVal); - Offset += sizeof(SK_U64); - } - - /* - * Store used buffer space - */ - *pLen = Offset; - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * SensorStat - OID handler function of OID_SKGE_SENSOR_XXX - * - * Description: - * Retrieves the statistic values of the I2C module, which handles - * the temperature and voltage sensors. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int SensorStat( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - unsigned int i; - unsigned int Index; - unsigned int Limit; - unsigned int Offset; - unsigned int Len; - SK_U32 Val32; - SK_U64 Val64; - - - /* - * Calculate instance if wished - */ - if ((Instance != (SK_U32)(-1))) { - - if ((Instance < 1) || (Instance > (SK_U32)pAC->I2c.MaxSens)) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - Index = (unsigned int)Instance -1; - Limit = (unsigned int)Instance; - } - else { - Index = 0; - Limit = (unsigned int) pAC->I2c.MaxSens; - } - - /* - * Check action - */ - if (Action != SK_PNMI_GET) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - /* Check length */ - switch (Id) { - - case OID_SKGE_SENSOR_VALUE: - case OID_SKGE_SENSOR_WAR_THRES_LOW: - case OID_SKGE_SENSOR_WAR_THRES_UPP: - case OID_SKGE_SENSOR_ERR_THRES_LOW: - case OID_SKGE_SENSOR_ERR_THRES_UPP: - if (*pLen < (Limit - Index) * sizeof(SK_U32)) { - - *pLen = (Limit - Index) * sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_SENSOR_DESCR: - for (Offset = 0, i = Index; i < Limit; i ++) { - - Len = (unsigned int) - SK_STRLEN(pAC->I2c.SenTable[i].SenDesc) + 1; - if (Len >= SK_PNMI_STRINGLEN2) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR011, - SK_PNMI_ERR011MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - Offset += Len; - } - if (*pLen < Offset) { - - *pLen = Offset; - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_SENSOR_INDEX: - case OID_SKGE_SENSOR_TYPE: - case OID_SKGE_SENSOR_STATUS: - if (*pLen < Limit - Index) { - - *pLen = Limit - Index; - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_SENSOR_WAR_CTS: - case OID_SKGE_SENSOR_WAR_TIME: - case OID_SKGE_SENSOR_ERR_CTS: - case OID_SKGE_SENSOR_ERR_TIME: - if (*pLen < (Limit - Index) * sizeof(SK_U64)) { - - *pLen = (Limit - Index) * sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR012, - SK_PNMI_ERR012MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - - } - - /* - * Get value - */ - for (Offset = 0; Index < Limit; Index ++) { - - switch (Id) { - - case OID_SKGE_SENSOR_INDEX: - *(pBuf + Offset) = (char)Index; - Offset += sizeof(char); - break; - - case OID_SKGE_SENSOR_DESCR: - Len = SK_STRLEN(pAC->I2c.SenTable[Index].SenDesc); - SK_MEMCPY(pBuf + Offset + 1, - pAC->I2c.SenTable[Index].SenDesc, Len); - *(pBuf + Offset) = (char)Len; - Offset += Len + 1; - break; - - case OID_SKGE_SENSOR_TYPE: - *(pBuf + Offset) = - (char)pAC->I2c.SenTable[Index].SenType; - Offset += sizeof(char); - break; - - case OID_SKGE_SENSOR_VALUE: - Val32 = (SK_U32)pAC->I2c.SenTable[Index].SenValue; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - Offset += sizeof(SK_U32); - break; - - case OID_SKGE_SENSOR_WAR_THRES_LOW: - Val32 = (SK_U32)pAC->I2c.SenTable[Index]. - SenThreWarnLow; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - Offset += sizeof(SK_U32); - break; - - case OID_SKGE_SENSOR_WAR_THRES_UPP: - Val32 = (SK_U32)pAC->I2c.SenTable[Index]. - SenThreWarnHigh; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - Offset += sizeof(SK_U32); - break; - - case OID_SKGE_SENSOR_ERR_THRES_LOW: - Val32 = (SK_U32)pAC->I2c.SenTable[Index]. - SenThreErrLow; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - Offset += sizeof(SK_U32); - break; - - case OID_SKGE_SENSOR_ERR_THRES_UPP: - Val32 = pAC->I2c.SenTable[Index].SenThreErrHigh; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - Offset += sizeof(SK_U32); - break; - - case OID_SKGE_SENSOR_STATUS: - *(pBuf + Offset) = - (char)pAC->I2c.SenTable[Index].SenErrFlag; - Offset += sizeof(char); - break; - - case OID_SKGE_SENSOR_WAR_CTS: - Val64 = pAC->I2c.SenTable[Index].SenWarnCts; - SK_PNMI_STORE_U64(pBuf + Offset, Val64); - Offset += sizeof(SK_U64); - break; - - case OID_SKGE_SENSOR_ERR_CTS: - Val64 = pAC->I2c.SenTable[Index].SenErrCts; - SK_PNMI_STORE_U64(pBuf + Offset, Val64); - Offset += sizeof(SK_U64); - break; - - case OID_SKGE_SENSOR_WAR_TIME: - Val64 = SK_PNMI_HUNDREDS_SEC(pAC->I2c.SenTable[Index]. - SenBegWarnTS); - SK_PNMI_STORE_U64(pBuf + Offset, Val64); - Offset += sizeof(SK_U64); - break; - - case OID_SKGE_SENSOR_ERR_TIME: - Val64 = SK_PNMI_HUNDREDS_SEC(pAC->I2c.SenTable[Index]. - SenBegErrTS); - SK_PNMI_STORE_U64(pBuf + Offset, Val64); - Offset += sizeof(SK_U64); - break; - - default: - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_ERR, - ("SensorStat: Unknown OID should be handled before")); - - return (SK_PNMI_ERR_GENERAL); - } - } - - /* - * Store used buffer space - */ - *pLen = Offset; - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * Vpd - OID handler function of OID_SKGE_VPD_XXX - * - * Description: - * Get/preset/set of VPD data. As instance the name of a VPD key - * can be passed. The Instance parameter is a SK_U32 and can be - * used as a string buffer for the VPD key, because their maximum - * length is 4 byte. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int Vpd( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - SK_VPD_STATUS *pVpdStatus; - unsigned int BufLen; - char Buf[256]; - char KeyArr[SK_PNMI_VPD_ENTRIES][SK_PNMI_VPD_KEY_SIZE]; - char KeyStr[SK_PNMI_VPD_KEY_SIZE]; - unsigned int KeyNo; - unsigned int Offset; - unsigned int Index; - unsigned int FirstIndex; - unsigned int LastIndex; - unsigned int Len; - int Ret; - SK_U32 Val32; - - /* - * Get array of all currently stored VPD keys - */ - Ret = GetVpdKeyArr(pAC, IoC, &KeyArr[0][0], sizeof(KeyArr), &KeyNo); - if (Ret != SK_PNMI_ERR_OK) { - *pLen = 0; - return (Ret); - } - - /* - * If instance is not -1, try to find the requested VPD key for - * the multiple instance variables. The other OIDs as for example - * OID VPD_ACTION are single instance variables and must be - * handled separatly. - */ - FirstIndex = 0; - LastIndex = KeyNo; - - if ((Instance != (SK_U32)(-1))) { - - if (Id == OID_SKGE_VPD_KEY || Id == OID_SKGE_VPD_VALUE || - Id == OID_SKGE_VPD_ACCESS) { - - SK_STRNCPY(KeyStr, (char *)&Instance, 4); - KeyStr[4] = 0; - - for (Index = 0; Index < KeyNo; Index ++) { - - if (SK_STRCMP(KeyStr, KeyArr[Index]) == 0) { - FirstIndex = Index; - LastIndex = Index+1; - break; - } - } - if (Index == KeyNo) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - } - else if (Instance != 1) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - } - - /* - * Get value, if a query should be performed - */ - if (Action == SK_PNMI_GET) { - - switch (Id) { - - case OID_SKGE_VPD_FREE_BYTES: - /* Check length of buffer */ - if (*pLen < sizeof(SK_U32)) { - - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - /* Get number of free bytes */ - pVpdStatus = VpdStat(pAC, IoC); - if (pVpdStatus == NULL) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR017, - SK_PNMI_ERR017MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - if ((pVpdStatus->vpd_status & VPD_VALID) == 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR018, - SK_PNMI_ERR018MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - Val32 = (SK_U32)pVpdStatus->vpd_free_rw; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_VPD_ENTRIES_LIST: - /* Check length */ - for (Len = 0, Index = 0; Index < KeyNo; Index ++) { - - Len += SK_STRLEN(KeyArr[Index]) + 1; - } - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* Get value */ - *(pBuf) = (char)Len - 1; - for (Offset = 1, Index = 0; Index < KeyNo; Index ++) { - - Len = SK_STRLEN(KeyArr[Index]); - SK_MEMCPY(pBuf + Offset, KeyArr[Index], Len); - - Offset += Len; - - if (Index < KeyNo - 1) { - - *(pBuf + Offset) = ' '; - Offset ++; - } - } - *pLen = Offset; - break; - - case OID_SKGE_VPD_ENTRIES_NUMBER: - /* Check length */ - if (*pLen < sizeof(SK_U32)) { - - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - - Val32 = (SK_U32)KeyNo; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_VPD_KEY: - /* Check buffer length, if it is large enough */ - for (Len = 0, Index = FirstIndex; - Index < LastIndex; Index ++) { - - Len += SK_STRLEN(KeyArr[Index]) + 1; - } - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* - * Get the key to an intermediate buffer, because - * we have to prepend a length byte. - */ - for (Offset = 0, Index = FirstIndex; - Index < LastIndex; Index ++) { - - Len = SK_STRLEN(KeyArr[Index]); - - *(pBuf + Offset) = (char)Len; - SK_MEMCPY(pBuf + Offset + 1, KeyArr[Index], - Len); - Offset += Len + 1; - } - *pLen = Offset; - break; - - case OID_SKGE_VPD_VALUE: - /* Check the buffer length if it is large enough */ - for (Offset = 0, Index = FirstIndex; - Index < LastIndex; Index ++) { - - BufLen = 256; - if (VpdRead(pAC, IoC, KeyArr[Index], Buf, - (int *)&BufLen) > 0 || - BufLen >= SK_PNMI_VPD_DATALEN) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR021, - SK_PNMI_ERR021MSG); - - return (SK_PNMI_ERR_GENERAL); - } - Offset += BufLen + 1; - } - if (*pLen < Offset) { - - *pLen = Offset; - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* - * Get the value to an intermediate buffer, because - * we have to prepend a length byte. - */ - for (Offset = 0, Index = FirstIndex; - Index < LastIndex; Index ++) { - - BufLen = 256; - if (VpdRead(pAC, IoC, KeyArr[Index], Buf, - (int *)&BufLen) > 0 || - BufLen >= SK_PNMI_VPD_DATALEN) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR022, - SK_PNMI_ERR022MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - *(pBuf + Offset) = (char)BufLen; - SK_MEMCPY(pBuf + Offset + 1, Buf, BufLen); - Offset += BufLen + 1; - } - *pLen = Offset; - break; - - case OID_SKGE_VPD_ACCESS: - if (*pLen < LastIndex - FirstIndex) { - - *pLen = LastIndex - FirstIndex; - return (SK_PNMI_ERR_TOO_SHORT); - } - - for (Offset = 0, Index = FirstIndex; - Index < LastIndex; Index ++) { - - if (VpdMayWrite(KeyArr[Index])) { - - *(pBuf + Offset) = SK_PNMI_VPD_RW; - } - else { - *(pBuf + Offset) = SK_PNMI_VPD_RO; - } - Offset ++; - } - *pLen = Offset; - break; - - case OID_SKGE_VPD_ACTION: - Offset = LastIndex - FirstIndex; - if (*pLen < Offset) { - - *pLen = Offset; - return (SK_PNMI_ERR_TOO_SHORT); - } - SK_MEMSET(pBuf, 0, Offset); - *pLen = Offset; - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR023, - SK_PNMI_ERR023MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - else { - /* The only OID which can be set is VPD_ACTION */ - if (Id != OID_SKGE_VPD_ACTION) { - - if (Id == OID_SKGE_VPD_FREE_BYTES || - Id == OID_SKGE_VPD_ENTRIES_LIST || - Id == OID_SKGE_VPD_ENTRIES_NUMBER || - Id == OID_SKGE_VPD_KEY || - Id == OID_SKGE_VPD_VALUE || - Id == OID_SKGE_VPD_ACCESS) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR024, - SK_PNMI_ERR024MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* - * From this point we handle VPD_ACTION. Check the buffer - * length. It should at least have the size of one byte. - */ - if (*pLen < 1) { - - *pLen = 1; - return (SK_PNMI_ERR_TOO_SHORT); - } - - /* - * The first byte contains the VPD action type we should - * perform. - */ - switch (*pBuf) { - - case SK_PNMI_VPD_IGNORE: - /* Nothing to do */ - break; - - case SK_PNMI_VPD_CREATE: - /* - * We have to create a new VPD entry or we modify - * an existing one. Check first the buffer length. - */ - if (*pLen < 4) { - - *pLen = 4; - return (SK_PNMI_ERR_TOO_SHORT); - } - KeyStr[0] = pBuf[1]; - KeyStr[1] = pBuf[2]; - KeyStr[2] = 0; - - /* - * Is the entry writable or does it belong to the - * read-only area? - */ - if (!VpdMayWrite(KeyStr)) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - Offset = (int)pBuf[3] & 0xFF; - - SK_MEMCPY(Buf, pBuf + 4, Offset); - Buf[Offset] = 0; - - /* A preset ends here */ - if (Action == SK_PNMI_PRESET) { - - return (SK_PNMI_ERR_OK); - } - - /* Write the new entry or modify an existing one */ - Ret = VpdWrite(pAC, IoC, KeyStr, Buf); - if (Ret == SK_PNMI_VPD_NOWRITE ) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - else if (Ret != SK_PNMI_VPD_OK) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR025, - SK_PNMI_ERR025MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* - * Perform an update of the VPD data. This is - * not mandantory, but just to be sure. - */ - Ret = VpdUpdate(pAC, IoC); - if (Ret != SK_PNMI_VPD_OK) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR026, - SK_PNMI_ERR026MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - break; - - case SK_PNMI_VPD_DELETE: - /* Check if the buffer size is plausible */ - if (*pLen < 3) { - - *pLen = 3; - return (SK_PNMI_ERR_TOO_SHORT); - } - if (*pLen > 3) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - KeyStr[0] = pBuf[1]; - KeyStr[1] = pBuf[2]; - KeyStr[2] = 0; - - /* Find the passed key in the array */ - for (Index = 0; Index < KeyNo; Index ++) { - - if (SK_STRCMP(KeyStr, KeyArr[Index]) == 0) { - - break; - } - } - /* - * If we cannot find the key it is wrong, so we - * return an appropriate error value. - */ - if (Index == KeyNo) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - if (Action == SK_PNMI_PRESET) { - - return (SK_PNMI_ERR_OK); - } - - /* Ok, you wanted it and you will get it */ - Ret = VpdDelete(pAC, IoC, KeyStr); - if (Ret != SK_PNMI_VPD_OK) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR027, - SK_PNMI_ERR027MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* - * Perform an update of the VPD data. This is - * not mandantory, but just to be sure. - */ - Ret = VpdUpdate(pAC, IoC); - if (Ret != SK_PNMI_VPD_OK) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR028, - SK_PNMI_ERR028MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - break; - - default: - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * General - OID handler function of various single instance OIDs - * - * Description: - * The code is simple. No description necessary. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int General( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - int Ret; - unsigned int Index; - unsigned int Len; - unsigned int Offset; - unsigned int Val; - SK_U8 Val8; - SK_U16 Val16; - SK_U32 Val32; - SK_U64 Val64; - SK_U64 Val64RxHwErrs = 0; - SK_U64 Val64TxHwErrs = 0; - SK_BOOL Is64BitReq = SK_FALSE; - char Buf[256]; - int MacType; - - /* - * Check instance. We only handle single instance variables. - */ - if (Instance != (SK_U32)(-1) && Instance != 1) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - /* - * Check action. We only allow get requests. - */ - if (Action != SK_PNMI_GET) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - MacType = pAC->GIni.GIMacType; - - /* - * Check length for the various supported OIDs - */ - switch (Id) { - - case OID_GEN_XMIT_ERROR: - case OID_GEN_RCV_ERROR: - case OID_GEN_RCV_NO_BUFFER: -#ifndef SK_NDIS_64BIT_CTR - if (*pLen < sizeof(SK_U32)) { - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - -#else /* SK_NDIS_64BIT_CTR */ - - /* - * for compatibility, at least 32bit are required for oid - */ - if (*pLen < sizeof(SK_U32)) { - /* - * but indicate handling for 64bit values, - * if insufficient space is provided - */ - *pLen = sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - - Is64BitReq = (*pLen < sizeof(SK_U64)) ? SK_FALSE : SK_TRUE; -#endif /* SK_NDIS_64BIT_CTR */ - break; - - case OID_SKGE_PORT_NUMBER: - case OID_SKGE_DEVICE_TYPE: - case OID_SKGE_RESULT: - case OID_SKGE_RLMT_MONITOR_NUMBER: - case OID_GEN_TRANSMIT_QUEUE_LENGTH: - case OID_SKGE_TRAP_NUMBER: - case OID_SKGE_MDB_VERSION: - case OID_SKGE_BOARDLEVEL: - case OID_SKGE_CHIPID: - case OID_SKGE_RAMSIZE: - if (*pLen < sizeof(SK_U32)) { - - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_CHIPSET: - if (*pLen < sizeof(SK_U16)) { - - *pLen = sizeof(SK_U16); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_BUS_TYPE: - case OID_SKGE_BUS_SPEED: - case OID_SKGE_BUS_WIDTH: - case OID_SKGE_SENSOR_NUMBER: - case OID_SKGE_CHKSM_NUMBER: - case OID_SKGE_VAUXAVAIL: - if (*pLen < sizeof(SK_U8)) { - - *pLen = sizeof(SK_U8); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_TX_SW_QUEUE_LEN: - case OID_SKGE_TX_SW_QUEUE_MAX: - case OID_SKGE_TX_RETRY: - case OID_SKGE_RX_INTR_CTS: - case OID_SKGE_TX_INTR_CTS: - case OID_SKGE_RX_NO_BUF_CTS: - case OID_SKGE_TX_NO_BUF_CTS: - case OID_SKGE_TX_USED_DESCR_NO: - case OID_SKGE_RX_DELIVERED_CTS: - case OID_SKGE_RX_OCTETS_DELIV_CTS: - case OID_SKGE_RX_HW_ERROR_CTS: - case OID_SKGE_TX_HW_ERROR_CTS: - case OID_SKGE_IN_ERRORS_CTS: - case OID_SKGE_OUT_ERROR_CTS: - case OID_SKGE_ERR_RECOVERY_CTS: - case OID_SKGE_SYSUPTIME: - if (*pLen < sizeof(SK_U64)) { - - *pLen = sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: - /* Checked later */ - break; - } - - /* Update statistic */ - if (Id == OID_SKGE_RX_HW_ERROR_CTS || - Id == OID_SKGE_TX_HW_ERROR_CTS || - Id == OID_SKGE_IN_ERRORS_CTS || - Id == OID_SKGE_OUT_ERROR_CTS || - Id == OID_GEN_XMIT_ERROR || - Id == OID_GEN_RCV_ERROR) { - - /* Force the XMAC to update its statistic counters and - * Increment semaphore to indicate that an update was - * already done. - */ - Ret = MacUpdate(pAC, IoC, 0, pAC->GIni.GIMacsFound - 1); - if (Ret != SK_PNMI_ERR_OK) { - - *pLen = 0; - return (Ret); - } - pAC->Pnmi.MacUpdatedFlag ++; - - /* - * Some OIDs consist of multiple hardware counters. Those - * values which are contained in all of them will be added - * now. - */ - switch (Id) { - - case OID_SKGE_RX_HW_ERROR_CTS: - case OID_SKGE_IN_ERRORS_CTS: - case OID_GEN_RCV_ERROR: - Val64RxHwErrs = - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_MISSED, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_FRAMING, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_OVERFLOW, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_JABBER, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_CARRIER, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_IRLENGTH, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_SYMBOL, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_SHORTS, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_RUNT, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_TOO_LONG, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_FCS, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HRX_CEXT, NetIndex); - break; - - case OID_SKGE_TX_HW_ERROR_CTS: - case OID_SKGE_OUT_ERROR_CTS: - case OID_GEN_XMIT_ERROR: - Val64TxHwErrs = - GetStatVal(pAC, IoC, 0, SK_PNMI_HTX_EXCESS_COL, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HTX_LATE_COL, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HTX_UNDERRUN, NetIndex) + - GetStatVal(pAC, IoC, 0, SK_PNMI_HTX_CARRIER, NetIndex); - break; - } - } - - /* - * Retrieve value - */ - switch (Id) { - - case OID_SKGE_SUPPORTED_LIST: - Len = ID_TABLE_SIZE * sizeof(SK_U32); - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - for (Offset = 0, Index = 0; Offset < Len; - Offset += sizeof(SK_U32), Index ++) { - - Val32 = (SK_U32)IdTable[Index].Id; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - } - *pLen = Len; - break; - - case OID_SKGE_BOARDLEVEL: - Val32 = (SK_U32)pAC->GIni.GILevel; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_PORT_NUMBER: - Val32 = (SK_U32)pAC->GIni.GIMacsFound; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_DEVICE_TYPE: - Val32 = (SK_U32)pAC->Pnmi.DeviceType; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_DRIVER_DESCR: - if (pAC->Pnmi.pDriverDescription == NULL) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR007, - SK_PNMI_ERR007MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - Len = SK_STRLEN(pAC->Pnmi.pDriverDescription) + 1; - if (Len > SK_PNMI_STRINGLEN1) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR029, - SK_PNMI_ERR029MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - *pBuf = (char)(Len - 1); - SK_MEMCPY(pBuf + 1, pAC->Pnmi.pDriverDescription, Len - 1); - *pLen = Len; - break; - - case OID_SKGE_DRIVER_VERSION: - if (pAC->Pnmi.pDriverVersion == NULL) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR030, - SK_PNMI_ERR030MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - Len = SK_STRLEN(pAC->Pnmi.pDriverVersion) + 1; - if (Len > SK_PNMI_STRINGLEN1) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR031, - SK_PNMI_ERR031MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - *pBuf = (char)(Len - 1); - SK_MEMCPY(pBuf + 1, pAC->Pnmi.pDriverVersion, Len - 1); - *pLen = Len; - break; - - case OID_SKGE_DRIVER_RELDATE: - if (pAC->Pnmi.pDriverReleaseDate == NULL) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR030, - SK_PNMI_ERR053MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - Len = SK_STRLEN(pAC->Pnmi.pDriverReleaseDate) + 1; - if (Len > SK_PNMI_STRINGLEN1) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR031, - SK_PNMI_ERR054MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - *pBuf = (char)(Len - 1); - SK_MEMCPY(pBuf + 1, pAC->Pnmi.pDriverReleaseDate, Len - 1); - *pLen = Len; - break; - - case OID_SKGE_DRIVER_FILENAME: - if (pAC->Pnmi.pDriverFileName == NULL) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR030, - SK_PNMI_ERR055MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - Len = SK_STRLEN(pAC->Pnmi.pDriverFileName) + 1; - if (Len > SK_PNMI_STRINGLEN1) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR031, - SK_PNMI_ERR056MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - *pBuf = (char)(Len - 1); - SK_MEMCPY(pBuf + 1, pAC->Pnmi.pDriverFileName, Len - 1); - *pLen = Len; - break; - - case OID_SKGE_HW_DESCR: - /* - * The hardware description is located in the VPD. This - * query may move to the initialisation routine. But - * the VPD data is cached and therefore a call here - * will not make much difference. - */ - Len = 256; - if (VpdRead(pAC, IoC, VPD_NAME, Buf, (int *)&Len) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR032, - SK_PNMI_ERR032MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - Len ++; - if (Len > SK_PNMI_STRINGLEN1) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR033, - SK_PNMI_ERR033MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - *pBuf = (char)(Len - 1); - SK_MEMCPY(pBuf + 1, Buf, Len - 1); - *pLen = Len; - break; - - case OID_SKGE_HW_VERSION: - /* Oh, I love to do some string manipulation */ - if (*pLen < 5) { - - *pLen = 5; - return (SK_PNMI_ERR_TOO_SHORT); - } - Val8 = (SK_U8)pAC->GIni.GIPciHwRev; - pBuf[0] = 4; - pBuf[1] = 'v'; - pBuf[2] = (char)(0x30 | ((Val8 >> 4) & 0x0F)); - pBuf[3] = '.'; - pBuf[4] = (char)(0x30 | (Val8 & 0x0F)); - *pLen = 5; - break; - - case OID_SKGE_CHIPSET: - Val16 = pAC->Pnmi.Chipset; - SK_PNMI_STORE_U16(pBuf, Val16); - *pLen = sizeof(SK_U16); - break; - - case OID_SKGE_CHIPID: - Val32 = pAC->GIni.GIChipId; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_RAMSIZE: - Val32 = pAC->GIni.GIRamSize; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_VAUXAVAIL: - *pBuf = (char) pAC->GIni.GIVauxAvail; - *pLen = sizeof(char); - break; - - case OID_SKGE_BUS_TYPE: - *pBuf = (char) SK_PNMI_BUS_PCI; - *pLen = sizeof(char); - break; - - case OID_SKGE_BUS_SPEED: - *pBuf = pAC->Pnmi.PciBusSpeed; - *pLen = sizeof(char); - break; - - case OID_SKGE_BUS_WIDTH: - *pBuf = pAC->Pnmi.PciBusWidth; - *pLen = sizeof(char); - break; - - case OID_SKGE_RESULT: - Val32 = pAC->Pnmi.TestResult; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_SENSOR_NUMBER: - *pBuf = (char)pAC->I2c.MaxSens; - *pLen = sizeof(char); - break; - - case OID_SKGE_CHKSM_NUMBER: - *pBuf = SKCS_NUM_PROTOCOLS; - *pLen = sizeof(char); - break; - - case OID_SKGE_TRAP_NUMBER: - GetTrapQueueLen(pAC, &Len, &Val); - Val32 = (SK_U32)Val; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_TRAP: - GetTrapQueueLen(pAC, &Len, &Val); - if (*pLen < Len) { - - *pLen = Len; - return (SK_PNMI_ERR_TOO_SHORT); - } - CopyTrapQueue(pAC, pBuf); - *pLen = Len; - break; - - case OID_SKGE_RLMT_MONITOR_NUMBER: -/* XXX Not yet implemented by RLMT therefore we return zero elements */ - Val32 = 0; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_TX_SW_QUEUE_LEN: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].TxSwQueueLen; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].TxSwQueueLen + - pAC->Pnmi.BufPort[1].TxSwQueueLen; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].TxSwQueueLen; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].TxSwQueueLen + - pAC->Pnmi.Port[1].TxSwQueueLen; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - - case OID_SKGE_TX_SW_QUEUE_MAX: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].TxSwQueueMax; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].TxSwQueueMax + - pAC->Pnmi.BufPort[1].TxSwQueueMax; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].TxSwQueueMax; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].TxSwQueueMax + - pAC->Pnmi.Port[1].TxSwQueueMax; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_TX_RETRY: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].TxRetryCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].TxRetryCts + - pAC->Pnmi.BufPort[1].TxRetryCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].TxRetryCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].TxRetryCts + - pAC->Pnmi.Port[1].TxRetryCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_RX_INTR_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].RxIntrCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].RxIntrCts + - pAC->Pnmi.BufPort[1].RxIntrCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].RxIntrCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].RxIntrCts + - pAC->Pnmi.Port[1].RxIntrCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_TX_INTR_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].TxIntrCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].TxIntrCts + - pAC->Pnmi.BufPort[1].TxIntrCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].TxIntrCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].TxIntrCts + - pAC->Pnmi.Port[1].TxIntrCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_RX_NO_BUF_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].RxNoBufCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].RxNoBufCts + - pAC->Pnmi.BufPort[1].RxNoBufCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].RxNoBufCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].RxNoBufCts + - pAC->Pnmi.Port[1].RxNoBufCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_TX_NO_BUF_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].TxNoBufCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].TxNoBufCts + - pAC->Pnmi.BufPort[1].TxNoBufCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].TxNoBufCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].TxNoBufCts + - pAC->Pnmi.Port[1].TxNoBufCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_TX_USED_DESCR_NO: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].TxUsedDescrNo; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].TxUsedDescrNo + - pAC->Pnmi.BufPort[1].TxUsedDescrNo; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].TxUsedDescrNo; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].TxUsedDescrNo + - pAC->Pnmi.Port[1].TxUsedDescrNo; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_RX_DELIVERED_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].RxDeliveredCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].RxDeliveredCts + - pAC->Pnmi.BufPort[1].RxDeliveredCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].RxDeliveredCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].RxDeliveredCts + - pAC->Pnmi.Port[1].RxDeliveredCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_RX_OCTETS_DELIV_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].RxOctetsDeliveredCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].RxOctetsDeliveredCts + - pAC->Pnmi.BufPort[1].RxOctetsDeliveredCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].RxOctetsDeliveredCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].RxOctetsDeliveredCts + - pAC->Pnmi.Port[1].RxOctetsDeliveredCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_RX_HW_ERROR_CTS: - SK_PNMI_STORE_U64(pBuf, Val64RxHwErrs); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_TX_HW_ERROR_CTS: - SK_PNMI_STORE_U64(pBuf, Val64TxHwErrs); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_IN_ERRORS_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = Val64RxHwErrs + pAC->Pnmi.BufPort[NetIndex].RxNoBufCts; - } - /* Single net mode */ - else { - Val64 = Val64RxHwErrs + - pAC->Pnmi.BufPort[0].RxNoBufCts + - pAC->Pnmi.BufPort[1].RxNoBufCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = Val64RxHwErrs + pAC->Pnmi.Port[NetIndex].RxNoBufCts; - } - /* Single net mode */ - else { - Val64 = Val64RxHwErrs + - pAC->Pnmi.Port[0].RxNoBufCts + - pAC->Pnmi.Port[1].RxNoBufCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_OUT_ERROR_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = Val64TxHwErrs + pAC->Pnmi.BufPort[NetIndex].TxNoBufCts; - } - /* Single net mode */ - else { - Val64 = Val64TxHwErrs + - pAC->Pnmi.BufPort[0].TxNoBufCts + - pAC->Pnmi.BufPort[1].TxNoBufCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = Val64TxHwErrs + pAC->Pnmi.Port[NetIndex].TxNoBufCts; - } - /* Single net mode */ - else { - Val64 = Val64TxHwErrs + - pAC->Pnmi.Port[0].TxNoBufCts + - pAC->Pnmi.Port[1].TxNoBufCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_ERR_RECOVERY_CTS: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.BufPort[NetIndex].ErrRecoveryCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.BufPort[0].ErrRecoveryCts + - pAC->Pnmi.BufPort[1].ErrRecoveryCts; - } - } - else { - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - Val64 = pAC->Pnmi.Port[NetIndex].ErrRecoveryCts; - } - /* Single net mode */ - else { - Val64 = pAC->Pnmi.Port[0].ErrRecoveryCts + - pAC->Pnmi.Port[1].ErrRecoveryCts; - } - } - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_SYSUPTIME: - Val64 = SK_PNMI_HUNDREDS_SEC(SkOsGetTime(pAC)); - Val64 -= pAC->Pnmi.StartUpTime; - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_MDB_VERSION: - Val32 = SK_PNMI_MDB_VERSION; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_GEN_RCV_ERROR: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - Val64 = Val64RxHwErrs + pAC->Pnmi.BufPort[NetIndex].RxNoBufCts; - } - else { - Val64 = Val64RxHwErrs + pAC->Pnmi.Port[NetIndex].RxNoBufCts; - } - - /* - * by default 32bit values are evaluated - */ - if (!Is64BitReq) { - Val32 = (SK_U32)Val64; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - } - else { - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - } - break; - - case OID_GEN_XMIT_ERROR: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - Val64 = Val64TxHwErrs + pAC->Pnmi.BufPort[NetIndex].TxNoBufCts; - } - else { - Val64 = Val64TxHwErrs + pAC->Pnmi.Port[NetIndex].TxNoBufCts; - } - - /* - * by default 32bit values are evaluated - */ - if (!Is64BitReq) { - Val32 = (SK_U32)Val64; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - } - else { - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - } - break; - - case OID_GEN_RCV_NO_BUFFER: - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - Val64 = pAC->Pnmi.BufPort[NetIndex].RxNoBufCts; - } - else { - Val64 = pAC->Pnmi.Port[NetIndex].RxNoBufCts; - } - - /* - * by default 32bit values are evaluated - */ - if (!Is64BitReq) { - Val32 = (SK_U32)Val64; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - } - else { - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - } - break; - - case OID_GEN_TRANSMIT_QUEUE_LENGTH: - Val32 = (SK_U32)pAC->Pnmi.Port[NetIndex].TxSwQueueLen; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR034, - SK_PNMI_ERR034MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - if (Id == OID_SKGE_RX_HW_ERROR_CTS || - Id == OID_SKGE_TX_HW_ERROR_CTS || - Id == OID_SKGE_IN_ERRORS_CTS || - Id == OID_SKGE_OUT_ERROR_CTS || - Id == OID_GEN_XMIT_ERROR || - Id == OID_GEN_RCV_ERROR) { - - pAC->Pnmi.MacUpdatedFlag --; - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * Rlmt - OID handler function of OID_SKGE_RLMT_XXX single instance. - * - * Description: - * Get/Presets/Sets the RLMT OIDs. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int Rlmt( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - int Ret; - unsigned int PhysPortIndex; - unsigned int PhysPortMax; - SK_EVPARA EventParam; - SK_U32 Val32; - SK_U64 Val64; - - - /* - * Check instance. Only single instance OIDs are allowed here. - */ - if (Instance != (SK_U32)(-1) && Instance != 1) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - /* - * Perform the requested action. - */ - if (Action == SK_PNMI_GET) { - - /* - * Check if the buffer length is large enough. - */ - - switch (Id) { - - case OID_SKGE_RLMT_MODE: - case OID_SKGE_RLMT_PORT_ACTIVE: - case OID_SKGE_RLMT_PORT_PREFERRED: - if (*pLen < sizeof(SK_U8)) { - - *pLen = sizeof(SK_U8); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_RLMT_PORT_NUMBER: - if (*pLen < sizeof(SK_U32)) { - - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_RLMT_CHANGE_CTS: - case OID_SKGE_RLMT_CHANGE_TIME: - case OID_SKGE_RLMT_CHANGE_ESTIM: - case OID_SKGE_RLMT_CHANGE_THRES: - if (*pLen < sizeof(SK_U64)) { - - *pLen = sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR035, - SK_PNMI_ERR035MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* - * Update RLMT statistic and increment semaphores to indicate - * that an update was already done. Maybe RLMT will hold its - * statistic always up to date some time. Then we can - * remove this type of call. - */ - if ((Ret = RlmtUpdate(pAC, IoC, NetIndex)) != SK_PNMI_ERR_OK) { - - *pLen = 0; - return (Ret); - } - pAC->Pnmi.RlmtUpdatedFlag ++; - - /* - * Retrieve Value - */ - switch (Id) { - - case OID_SKGE_RLMT_MODE: - *pBuf = (char)pAC->Rlmt.Net[0].RlmtMode; - *pLen = sizeof(char); - break; - - case OID_SKGE_RLMT_PORT_NUMBER: - Val32 = (SK_U32)pAC->GIni.GIMacsFound; - SK_PNMI_STORE_U32(pBuf, Val32); - *pLen = sizeof(SK_U32); - break; - - case OID_SKGE_RLMT_PORT_ACTIVE: - *pBuf = 0; - /* - * If multiple ports may become active this OID - * doesn't make sense any more. A new variable in - * the port structure should be created. However, - * for this variable the first active port is - * returned. - */ - PhysPortMax = pAC->GIni.GIMacsFound; - - for (PhysPortIndex = 0; PhysPortIndex < PhysPortMax; - PhysPortIndex ++) { - - if (pAC->Pnmi.Port[PhysPortIndex].ActiveFlag) { - - *pBuf = (char)SK_PNMI_PORT_PHYS2LOG(PhysPortIndex); - break; - } - } - *pLen = sizeof(char); - break; - - case OID_SKGE_RLMT_PORT_PREFERRED: - *pBuf = (char)SK_PNMI_PORT_PHYS2LOG(pAC->Rlmt.Net[NetIndex].Preference); - *pLen = sizeof(char); - break; - - case OID_SKGE_RLMT_CHANGE_CTS: - Val64 = pAC->Pnmi.RlmtChangeCts; - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_RLMT_CHANGE_TIME: - Val64 = pAC->Pnmi.RlmtChangeTime; - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_RLMT_CHANGE_ESTIM: - Val64 = pAC->Pnmi.RlmtChangeEstimate.Estimate; - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - case OID_SKGE_RLMT_CHANGE_THRES: - Val64 = pAC->Pnmi.RlmtChangeThreshold; - SK_PNMI_STORE_U64(pBuf, Val64); - *pLen = sizeof(SK_U64); - break; - - default: - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_ERR, - ("Rlmt: Unknown OID should be handled before")); - - pAC->Pnmi.RlmtUpdatedFlag --; - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - pAC->Pnmi.RlmtUpdatedFlag --; - } - else { - /* Perform a preset or set */ - switch (Id) { - - case OID_SKGE_RLMT_MODE: - /* Check if the buffer length is plausible */ - if (*pLen < sizeof(char)) { - - *pLen = sizeof(char); - return (SK_PNMI_ERR_TOO_SHORT); - } - /* Check if the value range is correct */ - if (*pLen != sizeof(char) || - (*pBuf & SK_PNMI_RLMT_MODE_CHK_LINK) == 0 || - *(SK_U8 *)pBuf > 15) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - /* The preset ends here */ - if (Action == SK_PNMI_PRESET) { - - *pLen = 0; - return (SK_PNMI_ERR_OK); - } - /* Send an event to RLMT to change the mode */ - SK_MEMSET((char *)&EventParam, 0, sizeof(EventParam)); - EventParam.Para32[0] |= (SK_U32)(*pBuf); - EventParam.Para32[1] = 0; - if (SkRlmtEvent(pAC, IoC, SK_RLMT_MODE_CHANGE, - EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR037, - SK_PNMI_ERR037MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - break; - - case OID_SKGE_RLMT_PORT_PREFERRED: - /* Check if the buffer length is plausible */ - if (*pLen < sizeof(char)) { - - *pLen = sizeof(char); - return (SK_PNMI_ERR_TOO_SHORT); - } - /* Check if the value range is correct */ - if (*pLen != sizeof(char) || *(SK_U8 *)pBuf > - (SK_U8)pAC->GIni.GIMacsFound) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - /* The preset ends here */ - if (Action == SK_PNMI_PRESET) { - - *pLen = 0; - return (SK_PNMI_ERR_OK); - } - - /* - * Send an event to RLMT change the preferred port. - * A param of -1 means automatic mode. RLMT will - * make the decision which is the preferred port. - */ - SK_MEMSET((char *)&EventParam, 0, sizeof(EventParam)); - EventParam.Para32[0] = (SK_U32)(*pBuf) - 1; - EventParam.Para32[1] = NetIndex; - if (SkRlmtEvent(pAC, IoC, SK_RLMT_PREFPORT_CHANGE, - EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR038, - SK_PNMI_ERR038MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - break; - - case OID_SKGE_RLMT_CHANGE_THRES: - /* Check if the buffer length is plausible */ - if (*pLen < sizeof(SK_U64)) { - - *pLen = sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - /* - * There are not many restrictions to the - * value range. - */ - if (*pLen != sizeof(SK_U64)) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - /* A preset ends here */ - if (Action == SK_PNMI_PRESET) { - - *pLen = 0; - return (SK_PNMI_ERR_OK); - } - /* - * Store the new threshold, which will be taken - * on the next timer event. - */ - SK_PNMI_READ_U64(pBuf, Val64); - pAC->Pnmi.RlmtChangeThreshold = Val64; - break; - - default: - /* The other OIDs are not be able for set */ - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * RlmtStat - OID handler function of OID_SKGE_RLMT_XXX multiple instance. - * - * Description: - * Performs get requests on multiple instance variables. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int RlmtStat( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - unsigned int PhysPortMax; - unsigned int PhysPortIndex; - unsigned int Limit; - unsigned int Offset; - int Ret; - SK_U32 Val32; - SK_U64 Val64; - - /* - * Calculate the port indexes from the instance. - */ - PhysPortMax = pAC->GIni.GIMacsFound; - - if ((Instance != (SK_U32)(-1))) { - /* Check instance range */ - if ((Instance < 1) || (Instance > PhysPortMax)) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - /* Single net mode */ - PhysPortIndex = Instance - 1; - - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - PhysPortIndex = NetIndex; - } - - /* Both net modes */ - Limit = PhysPortIndex + 1; - } - else { - /* Single net mode */ - PhysPortIndex = 0; - Limit = PhysPortMax; - - /* Dual net mode */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - PhysPortIndex = NetIndex; - Limit = PhysPortIndex + 1; - } - } - - /* - * Currently only get requests are allowed. - */ - if (Action != SK_PNMI_GET) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - /* - * Check if the buffer length is large enough. - */ - switch (Id) { - - case OID_SKGE_RLMT_PORT_INDEX: - case OID_SKGE_RLMT_STATUS: - if (*pLen < (Limit - PhysPortIndex) * sizeof(SK_U32)) { - - *pLen = (Limit - PhysPortIndex) * sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_RLMT_TX_HELLO_CTS: - case OID_SKGE_RLMT_RX_HELLO_CTS: - case OID_SKGE_RLMT_TX_SP_REQ_CTS: - case OID_SKGE_RLMT_RX_SP_CTS: - if (*pLen < (Limit - PhysPortIndex) * sizeof(SK_U64)) { - - *pLen = (Limit - PhysPortIndex) * sizeof(SK_U64); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR039, - SK_PNMI_ERR039MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - - } - - /* - * Update statistic and increment semaphores to indicate that - * an update was already done. - */ - if ((Ret = RlmtUpdate(pAC, IoC, NetIndex)) != SK_PNMI_ERR_OK) { - - *pLen = 0; - return (Ret); - } - pAC->Pnmi.RlmtUpdatedFlag ++; - - /* - * Get value - */ - Offset = 0; - for (; PhysPortIndex < Limit; PhysPortIndex ++) { - - switch (Id) { - - case OID_SKGE_RLMT_PORT_INDEX: - Val32 = PhysPortIndex; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - Offset += sizeof(SK_U32); - break; - - case OID_SKGE_RLMT_STATUS: - if (pAC->Rlmt.Port[PhysPortIndex].PortState == - SK_RLMT_PS_INIT || - pAC->Rlmt.Port[PhysPortIndex].PortState == - SK_RLMT_PS_DOWN) { - - Val32 = SK_PNMI_RLMT_STATUS_ERROR; - } - else if (pAC->Pnmi.Port[PhysPortIndex].ActiveFlag) { - - Val32 = SK_PNMI_RLMT_STATUS_ACTIVE; - } - else { - Val32 = SK_PNMI_RLMT_STATUS_STANDBY; - } - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - Offset += sizeof(SK_U32); - break; - - case OID_SKGE_RLMT_TX_HELLO_CTS: - Val64 = pAC->Rlmt.Port[PhysPortIndex].TxHelloCts; - SK_PNMI_STORE_U64(pBuf + Offset, Val64); - Offset += sizeof(SK_U64); - break; - - case OID_SKGE_RLMT_RX_HELLO_CTS: - Val64 = pAC->Rlmt.Port[PhysPortIndex].RxHelloCts; - SK_PNMI_STORE_U64(pBuf + Offset, Val64); - Offset += sizeof(SK_U64); - break; - - case OID_SKGE_RLMT_TX_SP_REQ_CTS: - Val64 = pAC->Rlmt.Port[PhysPortIndex].TxSpHelloReqCts; - SK_PNMI_STORE_U64(pBuf + Offset, Val64); - Offset += sizeof(SK_U64); - break; - - case OID_SKGE_RLMT_RX_SP_CTS: - Val64 = pAC->Rlmt.Port[PhysPortIndex].RxSpHelloCts; - SK_PNMI_STORE_U64(pBuf + Offset, Val64); - Offset += sizeof(SK_U64); - break; - - default: - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_ERR, - ("RlmtStat: Unknown OID should be errored before")); - - pAC->Pnmi.RlmtUpdatedFlag --; - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - *pLen = Offset; - - pAC->Pnmi.RlmtUpdatedFlag --; - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * MacPrivateConf - OID handler function of OIDs concerning the configuration - * - * Description: - * Get/Presets/Sets the OIDs concerning the configuration. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int MacPrivateConf( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - unsigned int PhysPortMax; - unsigned int PhysPortIndex; - unsigned int LogPortMax; - unsigned int LogPortIndex; - unsigned int Limit; - unsigned int Offset; - char Val8; - char *pBufPtr; - int Ret; - SK_EVPARA EventParam; - SK_U32 Val32; - - /* - * Calculate instance if wished. MAC index 0 is the virtual MAC. - */ - PhysPortMax = pAC->GIni.GIMacsFound; - LogPortMax = SK_PNMI_PORT_PHYS2LOG(PhysPortMax); - - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { /* Dual net mode */ - LogPortMax--; - } - - if ((Instance != (SK_U32)(-1))) { /* Only one specific instance is queried */ - /* Check instance range */ - if ((Instance < 1) || (Instance > LogPortMax)) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - LogPortIndex = SK_PNMI_PORT_INST2LOG(Instance); - Limit = LogPortIndex + 1; - } - - else { /* Instance == (SK_U32)(-1), get all Instances of that OID */ - - LogPortIndex = 0; - Limit = LogPortMax; - } - - /* - * Perform action - */ - if (Action == SK_PNMI_GET) { - - /* Check length */ - switch (Id) { - - case OID_SKGE_PMD: - case OID_SKGE_CONNECTOR: - case OID_SKGE_LINK_CAP: - case OID_SKGE_LINK_MODE: - case OID_SKGE_LINK_MODE_STATUS: - case OID_SKGE_LINK_STATUS: - case OID_SKGE_FLOWCTRL_CAP: - case OID_SKGE_FLOWCTRL_MODE: - case OID_SKGE_FLOWCTRL_STATUS: - case OID_SKGE_PHY_OPERATION_CAP: - case OID_SKGE_PHY_OPERATION_MODE: - case OID_SKGE_PHY_OPERATION_STATUS: - case OID_SKGE_SPEED_CAP: - case OID_SKGE_SPEED_MODE: - case OID_SKGE_SPEED_STATUS: - if (*pLen < (Limit - LogPortIndex) * sizeof(SK_U8)) { - - *pLen = (Limit - LogPortIndex) * sizeof(SK_U8); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_MTU: - case OID_SKGE_PHY_TYPE: - if (*pLen < (Limit - LogPortIndex) * sizeof(SK_U32)) { - - *pLen = (Limit - LogPortIndex) * sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR041, - SK_PNMI_ERR041MSG); - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* - * Update statistic and increment semaphore to indicate - * that an update was already done. - */ - if ((Ret = SirqUpdate(pAC, IoC)) != SK_PNMI_ERR_OK) { - - *pLen = 0; - return (Ret); - } - pAC->Pnmi.SirqUpdatedFlag ++; - - /* - * Get value - */ - Offset = 0; - for (; LogPortIndex < Limit; LogPortIndex ++) { - - pBufPtr = pBuf + Offset; - - switch (Id) { - - case OID_SKGE_PMD: - *pBufPtr = pAC->Pnmi.PMD; - Offset += sizeof(char); - break; - - case OID_SKGE_CONNECTOR: - *pBufPtr = pAC->Pnmi.Connector; - Offset += sizeof(char); - break; - - case OID_SKGE_PHY_TYPE: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - continue; - } - else { - /* Get value for physical ports */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - Val32 = pAC->GIni.GP[PhysPortIndex].PhyType; - SK_PNMI_STORE_U32(pBufPtr, Val32); - } - } - else { /* DualNetMode */ - - Val32 = pAC->GIni.GP[NetIndex].PhyType; - SK_PNMI_STORE_U32(pBufPtr, Val32); - } - Offset += sizeof(SK_U32); - break; - - case OID_SKGE_LINK_CAP: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical ports */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PLinkCap; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PLinkCap; - } - Offset += sizeof(char); - break; - - case OID_SKGE_LINK_MODE: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical ports */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PLinkModeConf; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PLinkModeConf; - } - Offset += sizeof(char); - break; - - case OID_SKGE_LINK_MODE_STATUS: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical port */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = - CalculateLinkModeStatus(pAC, IoC, PhysPortIndex); - } - } - else { /* DualNetMode */ - - *pBufPtr = CalculateLinkModeStatus(pAC, IoC, NetIndex); - } - Offset += sizeof(char); - break; - - case OID_SKGE_LINK_STATUS: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical ports */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = CalculateLinkStatus(pAC, IoC, PhysPortIndex); - } - } - else { /* DualNetMode */ - - *pBufPtr = CalculateLinkStatus(pAC, IoC, NetIndex); - } - Offset += sizeof(char); - break; - - case OID_SKGE_FLOWCTRL_CAP: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical ports */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PFlowCtrlCap; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PFlowCtrlCap; - } - Offset += sizeof(char); - break; - - case OID_SKGE_FLOWCTRL_MODE: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical port */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PFlowCtrlMode; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PFlowCtrlMode; - } - Offset += sizeof(char); - break; - - case OID_SKGE_FLOWCTRL_STATUS: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical port */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PFlowCtrlStatus; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PFlowCtrlStatus; - } - Offset += sizeof(char); - break; - - case OID_SKGE_PHY_OPERATION_CAP: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical ports */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PMSCap; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PMSCap; - } - Offset += sizeof(char); - break; - - case OID_SKGE_PHY_OPERATION_MODE: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical port */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PMSMode; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PMSMode; - } - Offset += sizeof(char); - break; - - case OID_SKGE_PHY_OPERATION_STATUS: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical port */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PMSStatus; - } - } - else { - - *pBufPtr = pAC->GIni.GP[NetIndex].PMSStatus; - } - Offset += sizeof(char); - break; - - case OID_SKGE_SPEED_CAP: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical ports */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PLinkSpeedCap; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PLinkSpeedCap; - } - Offset += sizeof(char); - break; - - case OID_SKGE_SPEED_MODE: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical port */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PLinkSpeed; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PLinkSpeed; - } - Offset += sizeof(char); - break; - - case OID_SKGE_SPEED_STATUS: - if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */ - if (LogPortIndex == 0) { - /* Get value for virtual port */ - VirtualConf(pAC, IoC, Id, pBufPtr); - } - else { - /* Get value for physical port */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - - *pBufPtr = pAC->GIni.GP[PhysPortIndex].PLinkSpeedUsed; - } - } - else { /* DualNetMode */ - - *pBufPtr = pAC->GIni.GP[NetIndex].PLinkSpeedUsed; - } - Offset += sizeof(char); - break; - - case OID_SKGE_MTU: - Val32 = SK_DRIVER_GET_MTU(pAC, IoC, NetIndex); - SK_PNMI_STORE_U32(pBufPtr, Val32); - Offset += sizeof(SK_U32); - break; - - default: - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_ERR, - ("MacPrivateConf: Unknown OID should be handled before")); - - pAC->Pnmi.SirqUpdatedFlag --; - return (SK_PNMI_ERR_GENERAL); - } - } - *pLen = Offset; - pAC->Pnmi.SirqUpdatedFlag --; - - return (SK_PNMI_ERR_OK); - } - - /* - * From here SET or PRESET action. Check if the passed - * buffer length is plausible. - */ - switch (Id) { - - case OID_SKGE_LINK_MODE: - case OID_SKGE_FLOWCTRL_MODE: - case OID_SKGE_PHY_OPERATION_MODE: - case OID_SKGE_SPEED_MODE: - if (*pLen < Limit - LogPortIndex) { - - *pLen = Limit - LogPortIndex; - return (SK_PNMI_ERR_TOO_SHORT); - } - if (*pLen != Limit - LogPortIndex) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - break; - - case OID_SKGE_MTU: - if (*pLen < sizeof(SK_U32)) { - - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - if (*pLen != sizeof(SK_U32)) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - break; - - default: - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - /* - * Perform preset or set - */ - Offset = 0; - for (; LogPortIndex < Limit; LogPortIndex ++) { - - switch (Id) { - - case OID_SKGE_LINK_MODE: - /* Check the value range */ - Val8 = *(pBuf + Offset); - if (Val8 == 0) { - - Offset += sizeof(char); - break; - } - if (Val8 < SK_LMODE_HALF || - (LogPortIndex != 0 && Val8 > SK_LMODE_AUTOSENSE) || - (LogPortIndex == 0 && Val8 > SK_LMODE_INDETERMINATED)) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - /* The preset ends here */ - if (Action == SK_PNMI_PRESET) { - - return (SK_PNMI_ERR_OK); - } - - if (LogPortIndex == 0) { - - /* - * The virtual port consists of all currently - * active ports. Find them and send an event - * with the new link mode to SIRQ. - */ - for (PhysPortIndex = 0; - PhysPortIndex < PhysPortMax; - PhysPortIndex ++) { - - if (!pAC->Pnmi.Port[PhysPortIndex]. - ActiveFlag) { - - continue; - } - - EventParam.Para32[0] = PhysPortIndex; - EventParam.Para32[1] = (SK_U32)Val8; - if (SkGeSirqEvent(pAC, IoC, - SK_HWEV_SET_LMODE, - EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR043, - SK_PNMI_ERR043MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - } - else { - /* - * Send an event with the new link mode to - * the SIRQ module. - */ - EventParam.Para32[0] = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - EventParam.Para32[1] = (SK_U32)Val8; - if (SkGeSirqEvent(pAC, IoC, SK_HWEV_SET_LMODE, - EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR043, - SK_PNMI_ERR043MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - Offset += sizeof(char); - break; - - case OID_SKGE_FLOWCTRL_MODE: - /* Check the value range */ - Val8 = *(pBuf + Offset); - if (Val8 == 0) { - - Offset += sizeof(char); - break; - } - if (Val8 < SK_FLOW_MODE_NONE || - (LogPortIndex != 0 && Val8 > SK_FLOW_MODE_SYM_OR_REM) || - (LogPortIndex == 0 && Val8 > SK_FLOW_MODE_INDETERMINATED)) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - /* The preset ends here */ - if (Action == SK_PNMI_PRESET) { - - return (SK_PNMI_ERR_OK); - } - - if (LogPortIndex == 0) { - - /* - * The virtual port consists of all currently - * active ports. Find them and send an event - * with the new flow control mode to SIRQ. - */ - for (PhysPortIndex = 0; - PhysPortIndex < PhysPortMax; - PhysPortIndex ++) { - - if (!pAC->Pnmi.Port[PhysPortIndex]. - ActiveFlag) { - - continue; - } - - EventParam.Para32[0] = PhysPortIndex; - EventParam.Para32[1] = (SK_U32)Val8; - if (SkGeSirqEvent(pAC, IoC, - SK_HWEV_SET_FLOWMODE, - EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR044, - SK_PNMI_ERR044MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - } - else { - /* - * Send an event with the new flow control - * mode to the SIRQ module. - */ - EventParam.Para32[0] = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - EventParam.Para32[1] = (SK_U32)Val8; - if (SkGeSirqEvent(pAC, IoC, - SK_HWEV_SET_FLOWMODE, EventParam) - > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR044, - SK_PNMI_ERR044MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - Offset += sizeof(char); - break; - - case OID_SKGE_PHY_OPERATION_MODE : - /* Check the value range */ - Val8 = *(pBuf + Offset); - if (Val8 == 0) { - /* mode of this port remains unchanged */ - Offset += sizeof(char); - break; - } - if (Val8 < SK_MS_MODE_AUTO || - (LogPortIndex != 0 && Val8 > SK_MS_MODE_SLAVE) || - (LogPortIndex == 0 && Val8 > SK_MS_MODE_INDETERMINATED)) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - /* The preset ends here */ - if (Action == SK_PNMI_PRESET) { - - return (SK_PNMI_ERR_OK); - } - - if (LogPortIndex == 0) { - - /* - * The virtual port consists of all currently - * active ports. Find them and send an event - * with new master/slave (role) mode to SIRQ. - */ - for (PhysPortIndex = 0; - PhysPortIndex < PhysPortMax; - PhysPortIndex ++) { - - if (!pAC->Pnmi.Port[PhysPortIndex]. - ActiveFlag) { - - continue; - } - - EventParam.Para32[0] = PhysPortIndex; - EventParam.Para32[1] = (SK_U32)Val8; - if (SkGeSirqEvent(pAC, IoC, - SK_HWEV_SET_ROLE, - EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR042, - SK_PNMI_ERR042MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - } - else { - /* - * Send an event with the new master/slave - * (role) mode to the SIRQ module. - */ - EventParam.Para32[0] = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - EventParam.Para32[1] = (SK_U32)Val8; - if (SkGeSirqEvent(pAC, IoC, - SK_HWEV_SET_ROLE, EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR042, - SK_PNMI_ERR042MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - - Offset += sizeof(char); - break; - - case OID_SKGE_SPEED_MODE: - /* Check the value range */ - Val8 = *(pBuf + Offset); - if (Val8 == 0) { - - Offset += sizeof(char); - break; - } - if (Val8 < (SK_LSPEED_AUTO) || - (LogPortIndex != 0 && Val8 > (SK_LSPEED_1000MBPS)) || - (LogPortIndex == 0 && Val8 > (SK_LSPEED_INDETERMINATED))) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - /* The preset ends here */ - if (Action == SK_PNMI_PRESET) { - - return (SK_PNMI_ERR_OK); - } - - if (LogPortIndex == 0) { - - /* - * The virtual port consists of all currently - * active ports. Find them and send an event - * with the new flow control mode to SIRQ. - */ - for (PhysPortIndex = 0; - PhysPortIndex < PhysPortMax; - PhysPortIndex ++) { - - if (!pAC->Pnmi.Port[PhysPortIndex].ActiveFlag) { - - continue; - } - - EventParam.Para32[0] = PhysPortIndex; - EventParam.Para32[1] = (SK_U32)Val8; - if (SkGeSirqEvent(pAC, IoC, - SK_HWEV_SET_SPEED, - EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR045, - SK_PNMI_ERR045MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - } - else { - /* - * Send an event with the new flow control - * mode to the SIRQ module. - */ - EventParam.Para32[0] = SK_PNMI_PORT_LOG2PHYS( - pAC, LogPortIndex); - EventParam.Para32[1] = (SK_U32)Val8; - if (SkGeSirqEvent(pAC, IoC, - SK_HWEV_SET_SPEED, - EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, - SK_PNMI_ERR045, - SK_PNMI_ERR045MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - Offset += sizeof(char); - break; - - case OID_SKGE_MTU : - /* Check the value range */ - Val32 = *(SK_U32*)(pBuf + Offset); - if (Val32 == 0) { - /* mtu of this port remains unchanged */ - Offset += sizeof(SK_U32); - break; - } - if (SK_DRIVER_PRESET_MTU(pAC, IoC, NetIndex, Val32) != 0) { - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - /* The preset ends here */ - if (Action == SK_PNMI_PRESET) { - return (SK_PNMI_ERR_OK); - } - - if (SK_DRIVER_SET_MTU(pAC, IoC, NetIndex, Val32) != 0) { - return (SK_PNMI_ERR_GENERAL); - } - - Offset += sizeof(SK_U32); - break; - - default: - SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_ERR, - ("MacPrivateConf: Unknown OID should be handled before set")); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * Monitor - OID handler function for RLMT_MONITOR_XXX - * - * Description: - * Because RLMT currently does not support the monitoring of - * remote adapter cards, we return always an empty table. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_BAD_VALUE The passed value is not in the valid - * value range. - * SK_PNMI_ERR_READ_ONLY The OID is read-only and cannot be set. - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -PNMI_STATIC int Monitor( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - unsigned int Index; - unsigned int Limit; - unsigned int Offset; - unsigned int Entries; - - - /* - * Calculate instance if wished. - */ - /* XXX Not yet implemented. Return always an empty table. */ - Entries = 0; - - if ((Instance != (SK_U32)(-1))) { - - if ((Instance < 1) || (Instance > Entries)) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - Index = (unsigned int)Instance - 1; - Limit = (unsigned int)Instance; - } - else { - Index = 0; - Limit = Entries; - } - - /* - * Get/Set value - */ - if (Action == SK_PNMI_GET) { - - for (Offset=0; Index < Limit; Index ++) { - - switch (Id) { - - case OID_SKGE_RLMT_MONITOR_INDEX: - case OID_SKGE_RLMT_MONITOR_ADDR: - case OID_SKGE_RLMT_MONITOR_ERRS: - case OID_SKGE_RLMT_MONITOR_TIMESTAMP: - case OID_SKGE_RLMT_MONITOR_ADMIN: - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR046, - SK_PNMI_ERR046MSG); - - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } - *pLen = Offset; - } - else { - /* Only MONITOR_ADMIN can be set */ - if (Id != OID_SKGE_RLMT_MONITOR_ADMIN) { - - *pLen = 0; - return (SK_PNMI_ERR_READ_ONLY); - } - - /* Check if the length is plausible */ - if (*pLen < (Limit - Index)) { - - return (SK_PNMI_ERR_TOO_SHORT); - } - /* Okay, we have a wide value range */ - if (*pLen != (Limit - Index)) { - - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } -/* - for (Offset=0; Index < Limit; Index ++) { - } -*/ -/* - * XXX Not yet implemented. Return always BAD_VALUE, because the table - * is empty. - */ - *pLen = 0; - return (SK_PNMI_ERR_BAD_VALUE); - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * VirtualConf - Calculates the values of configuration OIDs for virtual port - * - * Description: - * We handle here the get of the configuration group OIDs, which are - * a little bit complicated. The virtual port consists of all currently - * active physical ports. If multiple ports are active and configured - * differently we get in some trouble to return a single value. So we - * get the value of the first active port and compare it with that of - * the other active ports. If they are not the same, we return a value - * that indicates that the state is indeterminated. - * - * Returns: - * Nothing - */ -PNMI_STATIC void VirtualConf( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf) /* Buffer used for the management data transfer */ -{ - unsigned int PhysPortMax; - unsigned int PhysPortIndex; - SK_U8 Val8; - SK_U32 Val32; - SK_BOOL PortActiveFlag; - SK_GEPORT *pPrt; - - *pBuf = 0; - PortActiveFlag = SK_FALSE; - PhysPortMax = pAC->GIni.GIMacsFound; - - for (PhysPortIndex = 0; PhysPortIndex < PhysPortMax; - PhysPortIndex ++) { - - pPrt = &pAC->GIni.GP[PhysPortIndex]; - - /* Check if the physical port is active */ - if (!pAC->Pnmi.Port[PhysPortIndex].ActiveFlag) { - - continue; - } - - PortActiveFlag = SK_TRUE; - - switch (Id) { - - case OID_SKGE_PHY_TYPE: - /* Check if it is the first active port */ - if (*pBuf == 0) { - Val32 = pPrt->PhyType; - SK_PNMI_STORE_U32(pBuf, Val32); - continue; - } - - case OID_SKGE_LINK_CAP: - - /* - * Different capabilities should not happen, but - * in the case of the cases OR them all together. - * From a curious point of view the virtual port - * is capable of all found capabilities. - */ - *pBuf |= pPrt->PLinkCap; - break; - - case OID_SKGE_LINK_MODE: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PLinkModeConf; - continue; - } - - /* - * If we find an active port with a different link - * mode than the first one we return a value that - * indicates that the link mode is indeterminated. - */ - if (*pBuf != pPrt->PLinkModeConf) { - - *pBuf = SK_LMODE_INDETERMINATED; - } - break; - - case OID_SKGE_LINK_MODE_STATUS: - /* Get the link mode of the physical port */ - Val8 = CalculateLinkModeStatus(pAC, IoC, PhysPortIndex); - - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = Val8; - continue; - } - - /* - * If we find an active port with a different link - * mode status than the first one we return a value - * that indicates that the link mode status is - * indeterminated. - */ - if (*pBuf != Val8) { - - *pBuf = SK_LMODE_STAT_INDETERMINATED; - } - break; - - case OID_SKGE_LINK_STATUS: - /* Get the link status of the physical port */ - Val8 = CalculateLinkStatus(pAC, IoC, PhysPortIndex); - - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = Val8; - continue; - } - - /* - * If we find an active port with a different link - * status than the first one, we return a value - * that indicates that the link status is - * indeterminated. - */ - if (*pBuf != Val8) { - - *pBuf = SK_PNMI_RLMT_LSTAT_INDETERMINATED; - } - break; - - case OID_SKGE_FLOWCTRL_CAP: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PFlowCtrlCap; - continue; - } - - /* - * From a curious point of view the virtual port - * is capable of all found capabilities. - */ - *pBuf |= pPrt->PFlowCtrlCap; - break; - - case OID_SKGE_FLOWCTRL_MODE: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PFlowCtrlMode; - continue; - } - - /* - * If we find an active port with a different flow - * control mode than the first one, we return a value - * that indicates that the mode is indeterminated. - */ - if (*pBuf != pPrt->PFlowCtrlMode) { - - *pBuf = SK_FLOW_MODE_INDETERMINATED; - } - break; - - case OID_SKGE_FLOWCTRL_STATUS: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PFlowCtrlStatus; - continue; - } - - /* - * If we find an active port with a different flow - * control status than the first one, we return a - * value that indicates that the status is - * indeterminated. - */ - if (*pBuf != pPrt->PFlowCtrlStatus) { - - *pBuf = SK_FLOW_STAT_INDETERMINATED; - } - break; - - case OID_SKGE_PHY_OPERATION_CAP: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PMSCap; - continue; - } - - /* - * From a curious point of view the virtual port - * is capable of all found capabilities. - */ - *pBuf |= pPrt->PMSCap; - break; - - case OID_SKGE_PHY_OPERATION_MODE: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PMSMode; - continue; - } - - /* - * If we find an active port with a different master/ - * slave mode than the first one, we return a value - * that indicates that the mode is indeterminated. - */ - if (*pBuf != pPrt->PMSMode) { - - *pBuf = SK_MS_MODE_INDETERMINATED; - } - break; - - case OID_SKGE_PHY_OPERATION_STATUS: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PMSStatus; - continue; - } - - /* - * If we find an active port with a different master/ - * slave status than the first one, we return a - * value that indicates that the status is - * indeterminated. - */ - if (*pBuf != pPrt->PMSStatus) { - - *pBuf = SK_MS_STAT_INDETERMINATED; - } - break; - - case OID_SKGE_SPEED_MODE: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PLinkSpeed; - continue; - } - - /* - * If we find an active port with a different flow - * control mode than the first one, we return a value - * that indicates that the mode is indeterminated. - */ - if (*pBuf != pPrt->PLinkSpeed) { - - *pBuf = SK_LSPEED_INDETERMINATED; - } - break; - - case OID_SKGE_SPEED_STATUS: - /* Check if it is the first active port */ - if (*pBuf == 0) { - - *pBuf = pPrt->PLinkSpeedUsed; - continue; - } - - /* - * If we find an active port with a different flow - * control status than the first one, we return a - * value that indicates that the status is - * indeterminated. - */ - if (*pBuf != pPrt->PLinkSpeedUsed) { - - *pBuf = SK_LSPEED_STAT_INDETERMINATED; - } - break; - } - } - - /* - * If no port is active return an indeterminated answer - */ - if (!PortActiveFlag) { - - switch (Id) { - - case OID_SKGE_LINK_CAP: - *pBuf = SK_LMODE_CAP_INDETERMINATED; - break; - - case OID_SKGE_LINK_MODE: - *pBuf = SK_LMODE_INDETERMINATED; - break; - - case OID_SKGE_LINK_MODE_STATUS: - *pBuf = SK_LMODE_STAT_INDETERMINATED; - break; - - case OID_SKGE_LINK_STATUS: - *pBuf = SK_PNMI_RLMT_LSTAT_INDETERMINATED; - break; - - case OID_SKGE_FLOWCTRL_CAP: - case OID_SKGE_FLOWCTRL_MODE: - *pBuf = SK_FLOW_MODE_INDETERMINATED; - break; - - case OID_SKGE_FLOWCTRL_STATUS: - *pBuf = SK_FLOW_STAT_INDETERMINATED; - break; - - case OID_SKGE_PHY_OPERATION_CAP: - *pBuf = SK_MS_CAP_INDETERMINATED; - break; - - case OID_SKGE_PHY_OPERATION_MODE: - *pBuf = SK_MS_MODE_INDETERMINATED; - break; - - case OID_SKGE_PHY_OPERATION_STATUS: - *pBuf = SK_MS_STAT_INDETERMINATED; - break; - case OID_SKGE_SPEED_CAP: - *pBuf = SK_LSPEED_CAP_INDETERMINATED; - break; - - case OID_SKGE_SPEED_MODE: - *pBuf = SK_LSPEED_INDETERMINATED; - break; - - case OID_SKGE_SPEED_STATUS: - *pBuf = SK_LSPEED_STAT_INDETERMINATED; - break; - } - } -} - -/***************************************************************************** - * - * CalculateLinkStatus - Determins the link status of a physical port - * - * Description: - * Determins the link status the following way: - * LSTAT_PHY_DOWN: Link is down - * LSTAT_AUTONEG: Auto-negotiation failed - * LSTAT_LOG_DOWN: Link is up but RLMT did not yet put the port - * logically up. - * LSTAT_LOG_UP: RLMT marked the port as up - * - * Returns: - * Link status of physical port - */ -PNMI_STATIC SK_U8 CalculateLinkStatus( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -unsigned int PhysPortIndex) /* Physical port index */ -{ - SK_U8 Result; - - if (!pAC->GIni.GP[PhysPortIndex].PHWLinkUp) { - - Result = SK_PNMI_RLMT_LSTAT_PHY_DOWN; - } - else if (pAC->GIni.GP[PhysPortIndex].PAutoNegFail > 0) { - - Result = SK_PNMI_RLMT_LSTAT_AUTONEG; - } - else if (!pAC->Rlmt.Port[PhysPortIndex].PortDown) { - - Result = SK_PNMI_RLMT_LSTAT_LOG_UP; - } - else { - Result = SK_PNMI_RLMT_LSTAT_LOG_DOWN; - } - - return (Result); -} - -/***************************************************************************** - * - * CalculateLinkModeStatus - Determins the link mode status of a phys. port - * - * Description: - * The COMMON module only tells us if the mode is half or full duplex. - * But in the decade of auto sensing it is useful for the user to - * know if the mode was negotiated or forced. Therefore we have a - * look to the mode, which was last used by the negotiation process. - * - * Returns: - * The link mode status - */ -PNMI_STATIC SK_U8 CalculateLinkModeStatus( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -unsigned int PhysPortIndex) /* Physical port index */ -{ - SK_U8 Result; - - /* Get the current mode, which can be full or half duplex */ - Result = pAC->GIni.GP[PhysPortIndex].PLinkModeStatus; - - /* Check if no valid mode could be found (link is down) */ - if (Result < SK_LMODE_STAT_HALF) { - - Result = SK_LMODE_STAT_UNKNOWN; - } - else if (pAC->GIni.GP[PhysPortIndex].PLinkMode >= SK_LMODE_AUTOHALF) { - - /* - * Auto-negotiation was used to bring up the link. Change - * the already found duplex status that it indicates - * auto-negotiation was involved. - */ - if (Result == SK_LMODE_STAT_HALF) { - - Result = SK_LMODE_STAT_AUTOHALF; - } - else if (Result == SK_LMODE_STAT_FULL) { - - Result = SK_LMODE_STAT_AUTOFULL; - } - } - - return (Result); -} - -/***************************************************************************** - * - * GetVpdKeyArr - Obtain an array of VPD keys - * - * Description: - * Read the VPD keys and build an array of VPD keys, which are - * easy to access. - * - * Returns: - * SK_PNMI_ERR_OK Task successfully performed. - * SK_PNMI_ERR_GENERAL Something went wrong. - */ -PNMI_STATIC int GetVpdKeyArr( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -char *pKeyArr, /* Ptr KeyArray */ -unsigned int KeyArrLen, /* Length of array in bytes */ -unsigned int *pKeyNo) /* Number of keys */ -{ - unsigned int BufKeysLen = SK_PNMI_VPD_BUFSIZE; - char BufKeys[SK_PNMI_VPD_BUFSIZE]; - unsigned int StartOffset; - unsigned int Offset; - int Index; - int Ret; - - - SK_MEMSET(pKeyArr, 0, KeyArrLen); - - /* - * Get VPD key list - */ - Ret = VpdKeys(pAC, IoC, (char *)&BufKeys, (int *)&BufKeysLen, - (int *)pKeyNo); - if (Ret > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR014, - SK_PNMI_ERR014MSG); - - return (SK_PNMI_ERR_GENERAL); - } - /* If no keys are available return now */ - if (*pKeyNo == 0 || BufKeysLen == 0) { - - return (SK_PNMI_ERR_OK); - } - /* - * If the key list is too long for us trunc it and give a - * errorlog notification. This case should not happen because - * the maximum number of keys is limited due to RAM limitations - */ - if (*pKeyNo > SK_PNMI_VPD_ENTRIES) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR015, - SK_PNMI_ERR015MSG); - - *pKeyNo = SK_PNMI_VPD_ENTRIES; - } - - /* - * Now build an array of fixed string length size and copy - * the keys together. - */ - for (Index = 0, StartOffset = 0, Offset = 0; Offset < BufKeysLen; - Offset ++) { - - if (BufKeys[Offset] != 0) { - - continue; - } - - if (Offset - StartOffset > SK_PNMI_VPD_KEY_SIZE) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR016, - SK_PNMI_ERR016MSG); - return (SK_PNMI_ERR_GENERAL); - } - - SK_STRNCPY(pKeyArr + Index * SK_PNMI_VPD_KEY_SIZE, - &BufKeys[StartOffset], SK_PNMI_VPD_KEY_SIZE); - - Index ++; - StartOffset = Offset + 1; - } - - /* Last key not zero terminated? Get it anyway */ - if (StartOffset < Offset) { - - SK_STRNCPY(pKeyArr + Index * SK_PNMI_VPD_KEY_SIZE, - &BufKeys[StartOffset], SK_PNMI_VPD_KEY_SIZE); - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * SirqUpdate - Let the SIRQ update its internal values - * - * Description: - * Just to be sure that the SIRQ module holds its internal data - * structures up to date, we send an update event before we make - * any access. - * - * Returns: - * SK_PNMI_ERR_OK Task successfully performed. - * SK_PNMI_ERR_GENERAL Something went wrong. - */ -PNMI_STATIC int SirqUpdate( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC) /* IO context handle */ -{ - SK_EVPARA EventParam; - - - /* Was the module already updated during the current PNMI call? */ - if (pAC->Pnmi.SirqUpdatedFlag > 0) { - - return (SK_PNMI_ERR_OK); - } - - /* Send an synchronuous update event to the module */ - SK_MEMSET((char *)&EventParam, 0, sizeof(EventParam)); - if (SkGeSirqEvent(pAC, IoC, SK_HWEV_UPDATE_STAT, EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR047, - SK_PNMI_ERR047MSG); - - return (SK_PNMI_ERR_GENERAL); - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * RlmtUpdate - Let the RLMT update its internal values - * - * Description: - * Just to be sure that the RLMT module holds its internal data - * structures up to date, we send an update event before we make - * any access. - * - * Returns: - * SK_PNMI_ERR_OK Task successfully performed. - * SK_PNMI_ERR_GENERAL Something went wrong. - */ -PNMI_STATIC int RlmtUpdate( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode allways zero */ -{ - SK_EVPARA EventParam; - - - /* Was the module already updated during the current PNMI call? */ - if (pAC->Pnmi.RlmtUpdatedFlag > 0) { - - return (SK_PNMI_ERR_OK); - } - - /* Send an synchronuous update event to the module */ - SK_MEMSET((char *)&EventParam, 0, sizeof(EventParam)); - EventParam.Para32[0] = NetIndex; - EventParam.Para32[1] = (SK_U32)-1; - if (SkRlmtEvent(pAC, IoC, SK_RLMT_STATS_UPDATE, EventParam) > 0) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR048, - SK_PNMI_ERR048MSG); - - return (SK_PNMI_ERR_GENERAL); - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * MacUpdate - Force the XMAC to output the current statistic - * - * Description: - * The XMAC holds its statistic internally. To obtain the current - * values we must send a command so that the statistic data will - * be written to a predefined memory area on the adapter. - * - * Returns: - * SK_PNMI_ERR_OK Task successfully performed. - * SK_PNMI_ERR_GENERAL Something went wrong. - */ -PNMI_STATIC int MacUpdate( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -unsigned int FirstMac, /* Index of the first Mac to be updated */ -unsigned int LastMac) /* Index of the last Mac to be updated */ -{ - unsigned int MacIndex; - - /* - * Were the statistics already updated during the - * current PNMI call? - */ - if (pAC->Pnmi.MacUpdatedFlag > 0) { - - return (SK_PNMI_ERR_OK); - } - - /* Send an update command to all MACs specified */ - for (MacIndex = FirstMac; MacIndex <= LastMac; MacIndex ++) { - - /* - * 2002-09-13 pweber: Freeze the current SW counters. - * (That should be done as close as - * possible to the update of the - * HW counters) - */ - if (pAC->GIni.GIMacType == SK_MAC_XMAC) { - pAC->Pnmi.BufPort[MacIndex] = pAC->Pnmi.Port[MacIndex]; - } - - /* 2002-09-13 pweber: Update the HW counter */ - if (pAC->GIni.GIFunc.pFnMacUpdateStats(pAC, IoC, MacIndex) != 0) { - - return (SK_PNMI_ERR_GENERAL); - } - } - - return (SK_PNMI_ERR_OK); -} - -/***************************************************************************** - * - * GetStatVal - Retrieve an XMAC statistic counter - * - * Description: - * Retrieves the statistic counter of a virtual or physical port. The - * virtual port is identified by the index 0. It consists of all - * currently active ports. To obtain the counter value for this port - * we must add the statistic counter of all active ports. To grant - * continuous counter values for the virtual port even when port - * switches occur we must additionally add a delta value, which was - * calculated during a SK_PNMI_EVT_RLMT_ACTIVE_UP event. - * - * Returns: - * Requested statistic value - */ -PNMI_STATIC SK_U64 GetStatVal( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -unsigned int LogPortIndex, /* Index of the logical Port to be processed */ -unsigned int StatIndex, /* Index to statistic value */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode allways zero */ -{ - unsigned int PhysPortIndex; - unsigned int PhysPortMax; - SK_U64 Val = 0; - - - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { /* Dual net mode */ - - PhysPortIndex = NetIndex; - - Val = GetPhysStatVal(pAC, IoC, PhysPortIndex, StatIndex); - } - else { /* Single Net mode */ - - if (LogPortIndex == 0) { - - PhysPortMax = pAC->GIni.GIMacsFound; - - /* Add counter of all active ports */ - for (PhysPortIndex = 0; PhysPortIndex < PhysPortMax; - PhysPortIndex ++) { - - if (pAC->Pnmi.Port[PhysPortIndex].ActiveFlag) { - - Val += GetPhysStatVal(pAC, IoC, PhysPortIndex, StatIndex); - } - } - - /* Correct value because of port switches */ - Val += pAC->Pnmi.VirtualCounterOffset[StatIndex]; - } - else { - /* Get counter value of physical port */ - PhysPortIndex = SK_PNMI_PORT_LOG2PHYS(pAC, LogPortIndex); - - Val = GetPhysStatVal(pAC, IoC, PhysPortIndex, StatIndex); - } - } - return (Val); -} - -/***************************************************************************** - * - * GetPhysStatVal - Get counter value for physical port - * - * Description: - * Builds a 64bit counter value. Except for the octet counters - * the lower 32bit are counted in hardware and the upper 32bit - * in software by monitoring counter overflow interrupts in the - * event handler. To grant continous counter values during XMAC - * resets (caused by a workaround) we must add a delta value. - * The delta was calculated in the event handler when a - * SK_PNMI_EVT_XMAC_RESET was received. - * - * Returns: - * Counter value - */ -PNMI_STATIC SK_U64 GetPhysStatVal( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -unsigned int PhysPortIndex, /* Index of the logical Port to be processed */ -unsigned int StatIndex) /* Index to statistic value */ -{ - SK_U64 Val = 0; - SK_U32 LowVal = 0; - SK_U32 HighVal = 0; - SK_U16 Word; - int MacType; - unsigned int HelpIndex; - SK_GEPORT *pPrt; - - SK_PNMI_PORT *pPnmiPrt; - SK_GEMACFUNC *pFnMac; - - pPrt = &pAC->GIni.GP[PhysPortIndex]; - - MacType = pAC->GIni.GIMacType; - - /* 2002-09-17 pweber: For XMAC, use the frozen SW counters (BufPort) */ - if (MacType == SK_MAC_XMAC) { - pPnmiPrt = &pAC->Pnmi.BufPort[PhysPortIndex]; - } - else { - pPnmiPrt = &pAC->Pnmi.Port[PhysPortIndex]; - } - - pFnMac = &pAC->GIni.GIFunc; - - switch (StatIndex) { - case SK_PNMI_HTX: - if (MacType == SK_MAC_GMAC) { - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[SK_PNMI_HTX_BROADCAST][MacType].Reg, - &LowVal); - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[SK_PNMI_HTX_MULTICAST][MacType].Reg, - &HighVal); - LowVal += HighVal; - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[SK_PNMI_HTX_UNICAST][MacType].Reg, - &HighVal); - LowVal += HighVal; - } - else { - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - } - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - - case SK_PNMI_HRX: - if (MacType == SK_MAC_GMAC) { - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[SK_PNMI_HRX_BROADCAST][MacType].Reg, - &LowVal); - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[SK_PNMI_HRX_MULTICAST][MacType].Reg, - &HighVal); - LowVal += HighVal; - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[SK_PNMI_HRX_UNICAST][MacType].Reg, - &HighVal); - LowVal += HighVal; - } - else { - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - } - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - - case SK_PNMI_HTX_OCTET: - case SK_PNMI_HRX_OCTET: - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &HighVal); - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex + 1][MacType].Reg, - &LowVal); - break; - - case SK_PNMI_HTX_BURST: - case SK_PNMI_HTX_EXCESS_DEF: - case SK_PNMI_HTX_CARRIER: - /* Not supported by GMAC */ - if (MacType == SK_MAC_GMAC) { - return (Val); - } - - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - - case SK_PNMI_HTX_MACC: - /* GMAC only supports PAUSE MAC control frames */ - if (MacType == SK_MAC_GMAC) { - HelpIndex = SK_PNMI_HTX_PMACC; - } - else { - HelpIndex = StatIndex; - } - - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[HelpIndex][MacType].Reg, - &LowVal); - - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - - case SK_PNMI_HTX_COL: - case SK_PNMI_HRX_UNDERSIZE: - /* Not supported by XMAC */ - if (MacType == SK_MAC_XMAC) { - return (Val); - } - - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - - case SK_PNMI_HTX_DEFFERAL: - /* Not supported by GMAC */ - if (MacType == SK_MAC_GMAC) { - return (Val); - } - - /* - * XMAC counts frames with deferred transmission - * even in full-duplex mode. - * - * In full-duplex mode the counter remains constant! - */ - if ((pPrt->PLinkModeStatus == SK_LMODE_STAT_AUTOFULL) || - (pPrt->PLinkModeStatus == SK_LMODE_STAT_FULL)) { - - LowVal = 0; - HighVal = 0; - } - else { - /* Otherwise get contents of hardware register */ - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - } - break; - - case SK_PNMI_HRX_BADOCTET: - /* Not supported by XMAC */ - if (MacType == SK_MAC_XMAC) { - return (Val); - } - - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &HighVal); - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex + 1][MacType].Reg, - &LowVal); - break; - - case SK_PNMI_HTX_OCTETLOW: - case SK_PNMI_HRX_OCTETLOW: - case SK_PNMI_HRX_BADOCTETLOW: - return (Val); - - case SK_PNMI_HRX_LONGFRAMES: - /* For XMAC the SW counter is managed by PNMI */ - if (MacType == SK_MAC_XMAC) { - return (pPnmiPrt->StatRxLongFrameCts); - } - - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - - case SK_PNMI_HRX_TOO_LONG: - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - - Val = (((SK_U64)HighVal << 32) | (SK_U64)LowVal); - - if (MacType == SK_MAC_GMAC) { - /* For GMAC the SW counter is additionally managed by PNMI */ - Val += pPnmiPrt->StatRxFrameTooLongCts; - } - else { - /* - * Frames longer than IEEE 802.3 frame max size are counted - * by XMAC in frame_too_long counter even reception of long - * frames was enabled and the frame was correct. - * So correct the value by subtracting RxLongFrame counter. - */ - Val -= pPnmiPrt->StatRxLongFrameCts; - } - - LowVal = (SK_U32)Val; - HighVal = (SK_U32)(Val >> 32); - break; - - case SK_PNMI_HRX_SHORTS: - /* Not supported by GMAC */ - if (MacType == SK_MAC_GMAC) { - /* GM_RXE_FRAG?? */ - return (Val); - } - - /* - * XMAC counts short frame errors even if link down (#10620) - * - * If link-down the counter remains constant - */ - if (pPrt->PLinkModeStatus != SK_LMODE_STAT_UNKNOWN) { - - /* Otherwise get incremental difference */ - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - - Val = (((SK_U64)HighVal << 32) | (SK_U64)LowVal); - Val -= pPnmiPrt->RxShortZeroMark; - - LowVal = (SK_U32)Val; - HighVal = (SK_U32)(Val >> 32); - } - break; - - case SK_PNMI_HRX_MACC: - case SK_PNMI_HRX_MACC_UNKWN: - case SK_PNMI_HRX_BURST: - case SK_PNMI_HRX_MISSED: - case SK_PNMI_HRX_FRAMING: - case SK_PNMI_HRX_CARRIER: - case SK_PNMI_HRX_IRLENGTH: - case SK_PNMI_HRX_SYMBOL: - case SK_PNMI_HRX_CEXT: - /* Not supported by GMAC */ - if (MacType == SK_MAC_GMAC) { - return (Val); - } - - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - - case SK_PNMI_HRX_PMACC_ERR: - /* For GMAC the SW counter is managed by PNMI */ - if (MacType == SK_MAC_GMAC) { - return (pPnmiPrt->StatRxPMaccErr); - } - - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - - /* SW counter managed by PNMI */ - case SK_PNMI_HTX_SYNC: - LowVal = (SK_U32)pPnmiPrt->StatSyncCts; - HighVal = (SK_U32)(pPnmiPrt->StatSyncCts >> 32); - break; - - /* SW counter managed by PNMI */ - case SK_PNMI_HTX_SYNC_OCTET: - LowVal = (SK_U32)pPnmiPrt->StatSyncOctetsCts; - HighVal = (SK_U32)(pPnmiPrt->StatSyncOctetsCts >> 32); - break; - - case SK_PNMI_HRX_FCS: - /* - * Broadcom filters FCS errors and counts it in - * Receive Error Counter register - */ - if (pPrt->PhyType == SK_PHY_BCOM) { - /* do not read while not initialized (PHY_READ hangs!)*/ - if (pPrt->PState != SK_PRT_RESET) { - SkXmPhyRead(pAC, IoC, PhysPortIndex, PHY_BCOM_RE_CTR, &Word); - - LowVal = Word; - } - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - } - else { - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - } - break; - - default: - (void)pFnMac->pFnMacStatistic(pAC, IoC, PhysPortIndex, - StatAddr[StatIndex][MacType].Reg, - &LowVal); - HighVal = pPnmiPrt->CounterHigh[StatIndex]; - break; - } - - Val = (((SK_U64)HighVal << 32) | (SK_U64)LowVal); - - /* Correct value because of possible XMAC reset. XMAC Errata #2 */ - Val += pPnmiPrt->CounterOffset[StatIndex]; - - return (Val); -} - -/***************************************************************************** - * - * ResetCounter - Set all counters and timestamps to zero - * - * Description: - * Notifies other common modules which store statistic data to - * reset their counters and finally reset our own counters. - * - * Returns: - * Nothing - */ -PNMI_STATIC void ResetCounter( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -SK_U32 NetIndex) -{ - unsigned int PhysPortIndex; - SK_EVPARA EventParam; - - - SK_MEMSET((char *)&EventParam, 0, sizeof(EventParam)); - - /* Notify sensor module */ - SkEventQueue(pAC, SKGE_I2C, SK_I2CEV_CLEAR, EventParam); - - /* Notify RLMT module */ - EventParam.Para32[0] = NetIndex; - EventParam.Para32[1] = (SK_U32)-1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_STATS_CLEAR, EventParam); - EventParam.Para32[1] = 0; - - /* Notify SIRQ module */ - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_CLEAR_STAT, EventParam); - - /* Notify CSUM module */ -#ifdef SK_USE_CSUM - EventParam.Para32[0] = NetIndex; - EventParam.Para32[1] = (SK_U32)-1; - SkEventQueue(pAC, SKGE_CSUM, SK_CSUM_EVENT_CLEAR_PROTO_STATS, - EventParam); -#endif /* SK_USE_CSUM */ - - /* Clear XMAC statistic */ - for (PhysPortIndex = 0; PhysPortIndex < - (unsigned int)pAC->GIni.GIMacsFound; PhysPortIndex ++) { - - (void)pAC->GIni.GIFunc.pFnMacResetCounter(pAC, IoC, PhysPortIndex); - - SK_MEMSET((char *)&pAC->Pnmi.Port[PhysPortIndex].CounterHigh, - 0, sizeof(pAC->Pnmi.Port[PhysPortIndex].CounterHigh)); - SK_MEMSET((char *)&pAC->Pnmi.Port[PhysPortIndex]. - CounterOffset, 0, sizeof(pAC->Pnmi.Port[ - PhysPortIndex].CounterOffset)); - SK_MEMSET((char *)&pAC->Pnmi.Port[PhysPortIndex].StatSyncCts, - 0, sizeof(pAC->Pnmi.Port[PhysPortIndex].StatSyncCts)); - SK_MEMSET((char *)&pAC->Pnmi.Port[PhysPortIndex]. - StatSyncOctetsCts, 0, sizeof(pAC->Pnmi.Port[ - PhysPortIndex].StatSyncOctetsCts)); - SK_MEMSET((char *)&pAC->Pnmi.Port[PhysPortIndex]. - StatRxLongFrameCts, 0, sizeof(pAC->Pnmi.Port[ - PhysPortIndex].StatRxLongFrameCts)); - SK_MEMSET((char *)&pAC->Pnmi.Port[PhysPortIndex]. - StatRxFrameTooLongCts, 0, sizeof(pAC->Pnmi.Port[ - PhysPortIndex].StatRxFrameTooLongCts)); - SK_MEMSET((char *)&pAC->Pnmi.Port[PhysPortIndex]. - StatRxPMaccErr, 0, sizeof(pAC->Pnmi.Port[ - PhysPortIndex].StatRxPMaccErr)); - } - - /* - * Clear local statistics - */ - SK_MEMSET((char *)&pAC->Pnmi.VirtualCounterOffset, 0, - sizeof(pAC->Pnmi.VirtualCounterOffset)); - pAC->Pnmi.RlmtChangeCts = 0; - pAC->Pnmi.RlmtChangeTime = 0; - SK_MEMSET((char *)&pAC->Pnmi.RlmtChangeEstimate.EstValue[0], 0, - sizeof(pAC->Pnmi.RlmtChangeEstimate.EstValue)); - pAC->Pnmi.RlmtChangeEstimate.EstValueIndex = 0; - pAC->Pnmi.RlmtChangeEstimate.Estimate = 0; - pAC->Pnmi.Port[NetIndex].TxSwQueueMax = 0; - pAC->Pnmi.Port[NetIndex].TxRetryCts = 0; - pAC->Pnmi.Port[NetIndex].RxIntrCts = 0; - pAC->Pnmi.Port[NetIndex].TxIntrCts = 0; - pAC->Pnmi.Port[NetIndex].RxNoBufCts = 0; - pAC->Pnmi.Port[NetIndex].TxNoBufCts = 0; - pAC->Pnmi.Port[NetIndex].TxUsedDescrNo = 0; - pAC->Pnmi.Port[NetIndex].RxDeliveredCts = 0; - pAC->Pnmi.Port[NetIndex].RxOctetsDeliveredCts = 0; - pAC->Pnmi.Port[NetIndex].ErrRecoveryCts = 0; -} - -/***************************************************************************** - * - * GetTrapEntry - Get an entry in the trap buffer - * - * Description: - * The trap buffer stores various events. A user application somehow - * gets notified that an event occured and retrieves the trap buffer - * contens (or simply polls the buffer). The buffer is organized as - * a ring which stores the newest traps at the beginning. The oldest - * traps are overwritten by the newest ones. Each trap entry has a - * unique number, so that applications may detect new trap entries. - * - * Returns: - * A pointer to the trap entry - */ -PNMI_STATIC char* GetTrapEntry( -SK_AC *pAC, /* Pointer to adapter context */ -SK_U32 TrapId, /* SNMP ID of the trap */ -unsigned int Size) /* Space needed for trap entry */ -{ - unsigned int BufPad = pAC->Pnmi.TrapBufPad; - unsigned int BufFree = pAC->Pnmi.TrapBufFree; - unsigned int Beg = pAC->Pnmi.TrapQueueBeg; - unsigned int End = pAC->Pnmi.TrapQueueEnd; - char *pBuf = &pAC->Pnmi.TrapBuf[0]; - int Wrap; - unsigned int NeededSpace; - unsigned int EntrySize; - SK_U32 Val32; - SK_U64 Val64; - - - /* Last byte of entry will get a copy of the entry length */ - Size ++; - - /* - * Calculate needed buffer space */ - if (Beg >= Size) { - - NeededSpace = Size; - Wrap = SK_FALSE; - } - else { - NeededSpace = Beg + Size; - Wrap = SK_TRUE; - } - - /* - * Check if enough buffer space is provided. Otherwise - * free some entries. Leave one byte space between begin - * and end of buffer to make it possible to detect whether - * the buffer is full or empty - */ - while (BufFree < NeededSpace + 1) { - - if (End == 0) { - - End = SK_PNMI_TRAP_QUEUE_LEN; - } - - EntrySize = (unsigned int)*((unsigned char *)pBuf + End - 1); - BufFree += EntrySize; - End -= EntrySize; -#ifdef DEBUG - SK_MEMSET(pBuf + End, (char)(-1), EntrySize); -#endif /* DEBUG */ - if (End == BufPad) { -#ifdef DEBUG - SK_MEMSET(pBuf, (char)(-1), End); -#endif /* DEBUG */ - BufFree += End; - End = 0; - BufPad = 0; - } - } - - /* - * Insert new entry as first entry. Newest entries are - * stored at the beginning of the queue. - */ - if (Wrap) { - - BufPad = Beg; - Beg = SK_PNMI_TRAP_QUEUE_LEN - Size; - } - else { - Beg = Beg - Size; - } - BufFree -= NeededSpace; - - /* Save the current offsets */ - pAC->Pnmi.TrapQueueBeg = Beg; - pAC->Pnmi.TrapQueueEnd = End; - pAC->Pnmi.TrapBufPad = BufPad; - pAC->Pnmi.TrapBufFree = BufFree; - - /* Initialize the trap entry */ - *(pBuf + Beg + Size - 1) = (char)Size; - *(pBuf + Beg) = (char)Size; - Val32 = (pAC->Pnmi.TrapUnique) ++; - SK_PNMI_STORE_U32(pBuf + Beg + 1, Val32); - SK_PNMI_STORE_U32(pBuf + Beg + 1 + sizeof(SK_U32), TrapId); - Val64 = SK_PNMI_HUNDREDS_SEC(SkOsGetTime(pAC)); - SK_PNMI_STORE_U64(pBuf + Beg + 1 + 2 * sizeof(SK_U32), Val64); - - return (pBuf + Beg); -} - -/***************************************************************************** - * - * CopyTrapQueue - Copies the trap buffer for the TRAP OID - * - * Description: - * On a query of the TRAP OID the trap buffer contents will be - * copied continuously to the request buffer, which must be large - * enough. No length check is performed. - * - * Returns: - * Nothing - */ -PNMI_STATIC void CopyTrapQueue( -SK_AC *pAC, /* Pointer to adapter context */ -char *pDstBuf) /* Buffer to which the queued traps will be copied */ -{ - unsigned int BufPad = pAC->Pnmi.TrapBufPad; - unsigned int Trap = pAC->Pnmi.TrapQueueBeg; - unsigned int End = pAC->Pnmi.TrapQueueEnd; - char *pBuf = &pAC->Pnmi.TrapBuf[0]; - unsigned int Len; - unsigned int DstOff = 0; - - - while (Trap != End) { - - Len = (unsigned int)*(pBuf + Trap); - - /* - * Last byte containing a copy of the length will - * not be copied. - */ - *(pDstBuf + DstOff) = (char)(Len - 1); - SK_MEMCPY(pDstBuf + DstOff + 1, pBuf + Trap + 1, Len - 2); - DstOff += Len - 1; - - Trap += Len; - if (Trap == SK_PNMI_TRAP_QUEUE_LEN) { - - Trap = BufPad; - } - } -} - -/***************************************************************************** - * - * GetTrapQueueLen - Get the length of the trap buffer - * - * Description: - * Evaluates the number of currently stored traps and the needed - * buffer size to retrieve them. - * - * Returns: - * Nothing - */ -PNMI_STATIC void GetTrapQueueLen( -SK_AC *pAC, /* Pointer to adapter context */ -unsigned int *pLen, /* Length in Bytes of all queued traps */ -unsigned int *pEntries) /* Returns number of trapes stored in queue */ -{ - unsigned int BufPad = pAC->Pnmi.TrapBufPad; - unsigned int Trap = pAC->Pnmi.TrapQueueBeg; - unsigned int End = pAC->Pnmi.TrapQueueEnd; - char *pBuf = &pAC->Pnmi.TrapBuf[0]; - unsigned int Len; - unsigned int Entries = 0; - unsigned int TotalLen = 0; - - - while (Trap != End) { - - Len = (unsigned int)*(pBuf + Trap); - TotalLen += Len - 1; - Entries ++; - - Trap += Len; - if (Trap == SK_PNMI_TRAP_QUEUE_LEN) { - - Trap = BufPad; - } - } - - *pEntries = Entries; - *pLen = TotalLen; -} - -/***************************************************************************** - * - * QueueSimpleTrap - Store a simple trap to the trap buffer - * - * Description: - * A simple trap is a trap with now additional data. It consists - * simply of a trap code. - * - * Returns: - * Nothing - */ -PNMI_STATIC void QueueSimpleTrap( -SK_AC *pAC, /* Pointer to adapter context */ -SK_U32 TrapId) /* Type of sensor trap */ -{ - GetTrapEntry(pAC, TrapId, SK_PNMI_TRAP_SIMPLE_LEN); -} - -/***************************************************************************** - * - * QueueSensorTrap - Stores a sensor trap in the trap buffer - * - * Description: - * Gets an entry in the trap buffer and fills it with sensor related - * data. - * - * Returns: - * Nothing - */ -PNMI_STATIC void QueueSensorTrap( -SK_AC *pAC, /* Pointer to adapter context */ -SK_U32 TrapId, /* Type of sensor trap */ -unsigned int SensorIndex) /* Index of sensor which caused the trap */ -{ - char *pBuf; - unsigned int Offset; - unsigned int DescrLen; - SK_U32 Val32; - - - /* Get trap buffer entry */ - DescrLen = SK_STRLEN(pAC->I2c.SenTable[SensorIndex].SenDesc); - pBuf = GetTrapEntry(pAC, TrapId, - SK_PNMI_TRAP_SENSOR_LEN_BASE + DescrLen); - Offset = SK_PNMI_TRAP_SIMPLE_LEN; - - /* Store additionally sensor trap related data */ - Val32 = OID_SKGE_SENSOR_INDEX; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - *(pBuf + Offset + 4) = 4; - Val32 = (SK_U32)SensorIndex; - SK_PNMI_STORE_U32(pBuf + Offset + 5, Val32); - Offset += 9; - - Val32 = (SK_U32)OID_SKGE_SENSOR_DESCR; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - *(pBuf + Offset + 4) = (char)DescrLen; - SK_MEMCPY(pBuf + Offset + 5, pAC->I2c.SenTable[SensorIndex].SenDesc, - DescrLen); - Offset += DescrLen + 5; - - Val32 = OID_SKGE_SENSOR_TYPE; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - *(pBuf + Offset + 4) = 1; - *(pBuf + Offset + 5) = (char)pAC->I2c.SenTable[SensorIndex].SenType; - Offset += 6; - - Val32 = OID_SKGE_SENSOR_VALUE; - SK_PNMI_STORE_U32(pBuf + Offset, Val32); - *(pBuf + Offset + 4) = 4; - Val32 = (SK_U32)pAC->I2c.SenTable[SensorIndex].SenValue; - SK_PNMI_STORE_U32(pBuf + Offset + 5, Val32); -} - -/***************************************************************************** - * - * QueueRlmtNewMacTrap - Store a port switch trap in the trap buffer - * - * Description: - * Nothing further to explain. - * - * Returns: - * Nothing - */ -PNMI_STATIC void QueueRlmtNewMacTrap( -SK_AC *pAC, /* Pointer to adapter context */ -unsigned int ActiveMac) /* Index (0..n) of the currently active port */ -{ - char *pBuf; - SK_U32 Val32; - - - pBuf = GetTrapEntry(pAC, OID_SKGE_TRAP_RLMT_CHANGE_PORT, - SK_PNMI_TRAP_RLMT_CHANGE_LEN); - - Val32 = OID_SKGE_RLMT_PORT_ACTIVE; - SK_PNMI_STORE_U32(pBuf + SK_PNMI_TRAP_SIMPLE_LEN, Val32); - *(pBuf + SK_PNMI_TRAP_SIMPLE_LEN + 4) = 1; - *(pBuf + SK_PNMI_TRAP_SIMPLE_LEN + 5) = (char)ActiveMac; -} - -/***************************************************************************** - * - * QueueRlmtPortTrap - Store port related RLMT trap to trap buffer - * - * Description: - * Nothing further to explain. - * - * Returns: - * Nothing - */ -PNMI_STATIC void QueueRlmtPortTrap( -SK_AC *pAC, /* Pointer to adapter context */ -SK_U32 TrapId, /* Type of RLMT port trap */ -unsigned int PortIndex) /* Index of the port, which changed its state */ -{ - char *pBuf; - SK_U32 Val32; - - - pBuf = GetTrapEntry(pAC, TrapId, SK_PNMI_TRAP_RLMT_PORT_LEN); - - Val32 = OID_SKGE_RLMT_PORT_INDEX; - SK_PNMI_STORE_U32(pBuf + SK_PNMI_TRAP_SIMPLE_LEN, Val32); - *(pBuf + SK_PNMI_TRAP_SIMPLE_LEN + 4) = 1; - *(pBuf + SK_PNMI_TRAP_SIMPLE_LEN + 5) = (char)PortIndex; -} - -/***************************************************************************** - * - * CopyMac - Copies a MAC address - * - * Description: - * Nothing further to explain. - * - * Returns: - * Nothing - */ -PNMI_STATIC void CopyMac( -char *pDst, /* Pointer to destination buffer */ -SK_MAC_ADDR *pMac) /* Pointer of Source */ -{ - int i; - - - for (i = 0; i < sizeof(SK_MAC_ADDR); i ++) { - - *(pDst + i) = pMac->a[i]; - } -} - -#ifdef SK_POWER_MGMT -/***************************************************************************** - * - * PowerManagement - OID handler function of PowerManagement OIDs - * - * Description: - * The code is simple. No description necessary. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ - -PNMI_STATIC int PowerManagement( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* Get/PreSet/Set action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer to which to mgmt data will be retrieved */ -unsigned int *pLen, /* On call: buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode allways zero */ -{ - - SK_U32 RetCode = SK_PNMI_ERR_GENERAL; - - /* - * Check instance. We only handle single instance variables - */ - if (Instance != (SK_U32)(-1) && Instance != 1) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - - /* Check length */ - switch (Id) { - - case OID_PNP_CAPABILITIES: - if (*pLen < sizeof(SK_PNP_CAPABILITIES)) { - - *pLen = sizeof(SK_PNP_CAPABILITIES); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_PNP_SET_POWER: - case OID_PNP_QUERY_POWER: - if (*pLen < sizeof(SK_DEVICE_POWER_STATE)) - { - *pLen = sizeof(SK_DEVICE_POWER_STATE); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_PNP_ADD_WAKE_UP_PATTERN: - case OID_PNP_REMOVE_WAKE_UP_PATTERN: - if (*pLen < sizeof(SK_PM_PACKET_PATTERN)) { - - *pLen = sizeof(SK_PM_PACKET_PATTERN); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_PNP_ENABLE_WAKE_UP: - if (*pLen < sizeof(SK_U32)) { - - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - } - - /* - * Perform action - */ - if (Action == SK_PNMI_GET) { - - /* - * Get value - */ - switch (Id) { - - case OID_PNP_CAPABILITIES: - RetCode = SkPowerQueryPnPCapabilities(pAC, IoC, pBuf, pLen); - break; - - case OID_PNP_QUERY_POWER: - /* The Windows DDK describes: An OID_PNP_QUERY_POWER requests - the miniport to indicate whether it can transition its NIC - to the low-power state. - A miniport driver must always return NDIS_STATUS_SUCCESS - to a query of OID_PNP_QUERY_POWER. */ - *pLen = sizeof(SK_DEVICE_POWER_STATE); - RetCode = SK_PNMI_ERR_OK; - break; - - /* NDIS handles these OIDs as write-only. - * So in case of get action the buffer with written length = 0 - * is returned - */ - case OID_PNP_SET_POWER: - case OID_PNP_ADD_WAKE_UP_PATTERN: - case OID_PNP_REMOVE_WAKE_UP_PATTERN: - *pLen = 0; - RetCode = SK_PNMI_ERR_NOT_SUPPORTED; - break; - - case OID_PNP_ENABLE_WAKE_UP: - RetCode = SkPowerGetEnableWakeUp(pAC, IoC, pBuf, pLen); - break; - - default: - RetCode = SK_PNMI_ERR_GENERAL; - break; - } - - return (RetCode); - } - - - /* - * Perform preset or set - */ - - /* POWER module does not support PRESET action */ - if (Action == SK_PNMI_PRESET) { - return (SK_PNMI_ERR_OK); - } - - switch (Id) { - case OID_PNP_SET_POWER: - RetCode = SkPowerSetPower(pAC, IoC, pBuf, pLen); - break; - - case OID_PNP_ADD_WAKE_UP_PATTERN: - RetCode = SkPowerAddWakeUpPattern(pAC, IoC, pBuf, pLen); - break; - - case OID_PNP_REMOVE_WAKE_UP_PATTERN: - RetCode = SkPowerRemoveWakeUpPattern(pAC, IoC, pBuf, pLen); - break; - - case OID_PNP_ENABLE_WAKE_UP: - RetCode = SkPowerSetEnableWakeUp(pAC, IoC, pBuf, pLen); - break; - - default: - RetCode = SK_PNMI_ERR_READ_ONLY; - } - - return (RetCode); -} -#endif /* SK_POWER_MGMT */ - -#ifdef SK_DIAG_SUPPORT -/***************************************************************************** - * - * DiagActions - OID handler function of Diagnostic driver - * - * Description: - * The code is simple. No description necessary. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ - -PNMI_STATIC int DiagActions( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (1..n) that is to be queried or -1 */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - - SK_U32 DiagStatus; - SK_U32 RetCode = SK_PNMI_ERR_GENERAL; - - /* - * Check instance. We only handle single instance variables. - */ - if (Instance != (SK_U32)(-1) && Instance != 1) { - - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - /* - * Check length. - */ - switch (Id) { - - case OID_SKGE_DIAG_MODE: - if (*pLen < sizeof(SK_U32)) { - - *pLen = sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SK_PNMI_ERR040, SK_PNMI_ERR040MSG); - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* Perform action. */ - - /* GET value. */ - if (Action == SK_PNMI_GET) { - - switch (Id) { - - case OID_SKGE_DIAG_MODE: - DiagStatus = pAC->Pnmi.DiagAttached; - SK_PNMI_STORE_U32(pBuf, DiagStatus); - *pLen = sizeof(SK_U32); - RetCode = SK_PNMI_ERR_OK; - break; - - default: - *pLen = 0; - RetCode = SK_PNMI_ERR_GENERAL; - break; - } - return (RetCode); - } - - /* From here SET or PRESET value. */ - - /* PRESET value is not supported. */ - if (Action == SK_PNMI_PRESET) { - return (SK_PNMI_ERR_OK); - } - - /* SET value. */ - switch (Id) { - case OID_SKGE_DIAG_MODE: - - /* Handle the SET. */ - switch (*pBuf) { - - /* Attach the DIAG to this adapter. */ - case SK_DIAG_ATTACHED: - /* Check if we come from running */ - if (pAC->Pnmi.DiagAttached == SK_DIAG_RUNNING) { - - RetCode = SkDrvLeaveDiagMode(pAC); - - } - else if (pAC->Pnmi.DiagAttached == SK_DIAG_IDLE) { - - RetCode = SK_PNMI_ERR_OK; - } - - else { - - RetCode = SK_PNMI_ERR_GENERAL; - - } - - if (RetCode == SK_PNMI_ERR_OK) { - - pAC->Pnmi.DiagAttached = SK_DIAG_ATTACHED; - } - break; - - /* Enter the DIAG mode in the driver. */ - case SK_DIAG_RUNNING: - RetCode = SK_PNMI_ERR_OK; - - /* - * If DiagAttached is set, we can tell the driver - * to enter the DIAG mode. - */ - if (pAC->Pnmi.DiagAttached == SK_DIAG_ATTACHED) { - /* If DiagMode is not active, we can enter it. */ - if (!pAC->DiagModeActive) { - - RetCode = SkDrvEnterDiagMode(pAC); - } - else { - - RetCode = SK_PNMI_ERR_GENERAL; - } - } - else { - - RetCode = SK_PNMI_ERR_GENERAL; - } - - if (RetCode == SK_PNMI_ERR_OK) { - - pAC->Pnmi.DiagAttached = SK_DIAG_RUNNING; - } - break; - - case SK_DIAG_IDLE: - /* Check if we come from running */ - if (pAC->Pnmi.DiagAttached == SK_DIAG_RUNNING) { - - RetCode = SkDrvLeaveDiagMode(pAC); - - } - else if (pAC->Pnmi.DiagAttached == SK_DIAG_ATTACHED) { - - RetCode = SK_PNMI_ERR_OK; - } - - else { - - RetCode = SK_PNMI_ERR_GENERAL; - - } - - if (RetCode == SK_PNMI_ERR_OK) { - - pAC->Pnmi.DiagAttached = SK_DIAG_IDLE; - } - break; - - default: - RetCode = SK_PNMI_ERR_BAD_VALUE; - break; - } - break; - - default: - RetCode = SK_PNMI_ERR_GENERAL; - } - - if (RetCode == SK_PNMI_ERR_OK) { - *pLen = sizeof(SK_U32); - } - else { - - *pLen = 0; - } - return (RetCode); -} -#endif /* SK_DIAG_SUPPORT */ - -/***************************************************************************** - * - * Vct - OID handler function of OIDs - * - * Description: - * The code is simple. No description necessary. - * - * Returns: - * SK_PNMI_ERR_OK The request was performed successfully. - * SK_PNMI_ERR_GENERAL A general severe internal error occured. - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to contain - * the correct data (e.g. a 32bit value is - * needed, but a 16 bit value was passed). - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter). - * SK_PNMI_ERR_READ_ONLY Only the Get action is allowed. - * - */ - -PNMI_STATIC int Vct( -SK_AC *pAC, /* Pointer to adapter context */ -SK_IOC IoC, /* IO context handle */ -int Action, /* GET/PRESET/SET action */ -SK_U32 Id, /* Object ID that is to be processed */ -char *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* On call: pBuf buffer length. On return: used buffer */ -SK_U32 Instance, /* Instance (-1,2..n) that is to be queried */ -unsigned int TableIndex, /* Index to the Id table */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ - SK_GEPORT *pPrt; - SK_PNMI_VCT *pVctBackupData; - SK_U32 LogPortMax; - SK_U32 PhysPortMax; - SK_U32 PhysPortIndex; - SK_U32 Limit; - SK_U32 Offset; - SK_BOOL Link; - SK_U32 RetCode = SK_PNMI_ERR_GENERAL; - int i; - SK_EVPARA Para; - SK_U32 CableLength; - - /* - * Calculate the port indexes from the instance. - */ - PhysPortMax = pAC->GIni.GIMacsFound; - LogPortMax = SK_PNMI_PORT_PHYS2LOG(PhysPortMax); - - /* Dual net mode? */ - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - LogPortMax--; - } - - if ((Instance != (SK_U32) (-1))) { - /* Check instance range. */ - if ((Instance < 2) || (Instance > LogPortMax)) { - *pLen = 0; - return (SK_PNMI_ERR_UNKNOWN_INST); - } - - if (pAC->Pnmi.DualNetActiveFlag == SK_TRUE) { - PhysPortIndex = NetIndex; - } - else { - PhysPortIndex = Instance - 2; - } - Limit = PhysPortIndex + 1; - } - else { - /* - * Instance == (SK_U32) (-1), get all Instances of that OID. - * - * Not implemented yet. May be used in future releases. - */ - PhysPortIndex = 0; - Limit = PhysPortMax; - } - - pPrt = &pAC->GIni.GP[PhysPortIndex]; - if (pPrt->PHWLinkUp) { - Link = SK_TRUE; - } - else { - Link = SK_FALSE; - } - - /* Check MAC type */ - if (pPrt->PhyType != SK_PHY_MARV_COPPER) { - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* Initialize backup data pointer. */ - pVctBackupData = &pAC->Pnmi.VctBackup[PhysPortIndex]; - - /* Check action type */ - if (Action == SK_PNMI_GET) { - /* Check length */ - switch (Id) { - - case OID_SKGE_VCT_GET: - if (*pLen < (Limit - PhysPortIndex) * sizeof(SK_PNMI_VCT)) { - *pLen = (Limit - PhysPortIndex) * sizeof(SK_PNMI_VCT); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - case OID_SKGE_VCT_STATUS: - if (*pLen < (Limit - PhysPortIndex) * sizeof(SK_U8)) { - *pLen = (Limit - PhysPortIndex) * sizeof(SK_U8); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* Get value */ - Offset = 0; - for (; PhysPortIndex < Limit; PhysPortIndex++) { - switch (Id) { - - case OID_SKGE_VCT_GET: - if ((Link == SK_FALSE) && - (pAC->Pnmi.VctStatus[PhysPortIndex] & SK_PNMI_VCT_PENDING)) { - RetCode = SkGmCableDiagStatus(pAC, IoC, PhysPortIndex, SK_FALSE); - if (RetCode == 0) { - pAC->Pnmi.VctStatus[PhysPortIndex] &= ~SK_PNMI_VCT_PENDING; - pAC->Pnmi.VctStatus[PhysPortIndex] |= - (SK_PNMI_VCT_NEW_VCT_DATA | SK_PNMI_VCT_TEST_DONE); - - /* Copy results for later use to PNMI struct. */ - for (i = 0; i < 4; i++) { - if (pPrt->PMdiPairSts[i] == SK_PNMI_VCT_NORMAL_CABLE) { - if ((pPrt->PMdiPairLen[i] > 35) && (pPrt->PMdiPairLen[i] < 0xff)) { - pPrt->PMdiPairSts[i] = SK_PNMI_VCT_IMPEDANCE_MISMATCH; - } - } - if ((pPrt->PMdiPairLen[i] > 35) && (pPrt->PMdiPairLen[i] != 0xff)) { - CableLength = 1000 * (((175 * pPrt->PMdiPairLen[i]) / 210) - 28); - } - else { - CableLength = 0; - } - pVctBackupData->PMdiPairLen[i] = CableLength; - pVctBackupData->PMdiPairSts[i] = pPrt->PMdiPairSts[i]; - } - - Para.Para32[0] = PhysPortIndex; - Para.Para32[1] = -1; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_RESET, Para); - SkEventDispatcher(pAC, IoC); - } - else { - ; /* VCT test is running. */ - } - } - - /* Get all results. */ - CheckVctStatus(pAC, IoC, pBuf, Offset, PhysPortIndex); - Offset += sizeof(SK_U8); - *(pBuf + Offset) = pPrt->PCableLen; - Offset += sizeof(SK_U8); - for (i = 0; i < 4; i++) { - SK_PNMI_STORE_U32((pBuf + Offset), pVctBackupData->PMdiPairLen[i]); - Offset += sizeof(SK_U32); - } - for (i = 0; i < 4; i++) { - *(pBuf + Offset) = pVctBackupData->PMdiPairSts[i]; - Offset += sizeof(SK_U8); - } - - RetCode = SK_PNMI_ERR_OK; - break; - - case OID_SKGE_VCT_STATUS: - CheckVctStatus(pAC, IoC, pBuf, Offset, PhysPortIndex); - Offset += sizeof(SK_U8); - RetCode = SK_PNMI_ERR_OK; - break; - - default: - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } /* for */ - *pLen = Offset; - return (RetCode); - - } /* if SK_PNMI_GET */ - - /* - * From here SET or PRESET action. Check if the passed - * buffer length is plausible. - */ - - /* Check length */ - switch (Id) { - case OID_SKGE_VCT_SET: - if (*pLen < (Limit - PhysPortIndex) * sizeof(SK_U32)) { - *pLen = (Limit - PhysPortIndex) * sizeof(SK_U32); - return (SK_PNMI_ERR_TOO_SHORT); - } - break; - - default: - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - - /* - * Perform preset or set. - */ - - /* VCT does not support PRESET action. */ - if (Action == SK_PNMI_PRESET) { - return (SK_PNMI_ERR_OK); - } - - Offset = 0; - for (; PhysPortIndex < Limit; PhysPortIndex++) { - switch (Id) { - case OID_SKGE_VCT_SET: /* Start VCT test. */ - if (Link == SK_FALSE) { - SkGeStopPort(pAC, IoC, PhysPortIndex, SK_STOP_ALL, SK_SOFT_RST); - - RetCode = SkGmCableDiagStatus(pAC, IoC, PhysPortIndex, SK_TRUE); - if (RetCode == 0) { /* RetCode: 0 => Start! */ - pAC->Pnmi.VctStatus[PhysPortIndex] |= SK_PNMI_VCT_PENDING; - pAC->Pnmi.VctStatus[PhysPortIndex] &= ~SK_PNMI_VCT_NEW_VCT_DATA; - pAC->Pnmi.VctStatus[PhysPortIndex] &= ~SK_PNMI_VCT_LINK; - - /* - * Start VCT timer counter. - */ - SK_MEMSET((char *) &Para, 0, sizeof(Para)); - Para.Para32[0] = PhysPortIndex; - Para.Para32[1] = -1; - SkTimerStart(pAC, IoC, &pAC->Pnmi.VctTimeout[PhysPortIndex].VctTimer, - 4000000, SKGE_PNMI, SK_PNMI_EVT_VCT_RESET, Para); - SK_PNMI_STORE_U32((pBuf + Offset), RetCode); - RetCode = SK_PNMI_ERR_OK; - } - else { /* RetCode: 2 => Running! */ - SK_PNMI_STORE_U32((pBuf + Offset), RetCode); - RetCode = SK_PNMI_ERR_OK; - } - } - else { /* RetCode: 4 => Link! */ - RetCode = 4; - SK_PNMI_STORE_U32((pBuf + Offset), RetCode); - RetCode = SK_PNMI_ERR_OK; - } - Offset += sizeof(SK_U32); - break; - - default: - *pLen = 0; - return (SK_PNMI_ERR_GENERAL); - } - } /* for */ - *pLen = Offset; - return (RetCode); - -} /* Vct */ - - -PNMI_STATIC void CheckVctStatus( -SK_AC *pAC, -SK_IOC IoC, -char *pBuf, -SK_U32 Offset, -SK_U32 PhysPortIndex) -{ - SK_GEPORT *pPrt; - SK_PNMI_VCT *pVctData; - SK_U32 RetCode; - - pPrt = &pAC->GIni.GP[PhysPortIndex]; - - pVctData = (SK_PNMI_VCT *) (pBuf + Offset); - pVctData->VctStatus = SK_PNMI_VCT_NONE; - - if (!pPrt->PHWLinkUp) { - - /* Was a VCT test ever made before? */ - if (pAC->Pnmi.VctStatus[PhysPortIndex] & SK_PNMI_VCT_TEST_DONE) { - if ((pAC->Pnmi.VctStatus[PhysPortIndex] & SK_PNMI_VCT_LINK)) { - pVctData->VctStatus |= SK_PNMI_VCT_OLD_VCT_DATA; - } - else { - pVctData->VctStatus |= SK_PNMI_VCT_NEW_VCT_DATA; - } - } - - /* Check VCT test status. */ - RetCode = SkGmCableDiagStatus(pAC,IoC, PhysPortIndex, SK_FALSE); - if (RetCode == 2) { /* VCT test is running. */ - pVctData->VctStatus |= SK_PNMI_VCT_RUNNING; - } - else { /* VCT data was copied to pAC here. Check PENDING state. */ - if (pAC->Pnmi.VctStatus[PhysPortIndex] & SK_PNMI_VCT_PENDING) { - pVctData->VctStatus |= SK_PNMI_VCT_NEW_VCT_DATA; - } - } - - if (pPrt->PCableLen != 0xff) { /* Old DSP value. */ - pVctData->VctStatus |= SK_PNMI_VCT_OLD_DSP_DATA; - } - } - else { - - /* Was a VCT test ever made before? */ - if (pAC->Pnmi.VctStatus[PhysPortIndex] & SK_PNMI_VCT_TEST_DONE) { - pVctData->VctStatus &= ~SK_PNMI_VCT_NEW_VCT_DATA; - pVctData->VctStatus |= SK_PNMI_VCT_OLD_VCT_DATA; - } - - /* DSP only valid in 100/1000 modes. */ - if (pAC->GIni.GP[PhysPortIndex].PLinkSpeedUsed != - SK_LSPEED_STAT_10MBPS) { - pVctData->VctStatus |= SK_PNMI_VCT_NEW_DSP_DATA; - } - } -} /* CheckVctStatus */ - - -/***************************************************************************** - * - * SkPnmiGenIoctl - Handles new generic PNMI IOCTL, calls the needed - * PNMI function depending on the subcommand and - * returns all data belonging to the complete database - * or OID request. - * - * Description: - * Looks up the requested subcommand, calls the corresponding handler - * function and passes all required parameters to it. - * The function is called by the driver. It is needed to handle the new - * generic PNMI IOCTL. This IOCTL is given to the driver and contains both - * the OID and a subcommand to decide what kind of request has to be done. - * - * Returns: - * SK_PNMI_ERR_OK The request was successfully performed - * SK_PNMI_ERR_GENERAL A general severe internal error occured - * SK_PNMI_ERR_TOO_SHORT The passed buffer is too short to take - * the data. - * SK_PNMI_ERR_UNKNOWN_OID The requested OID is unknown - * SK_PNMI_ERR_UNKNOWN_INST The requested instance of the OID doesn't - * exist (e.g. port instance 3 on a two port - * adapter. - */ -int SkPnmiGenIoctl( -SK_AC *pAC, /* Pointer to adapter context struct */ -SK_IOC IoC, /* I/O context */ -void *pBuf, /* Buffer used for the management data transfer */ -unsigned int *pLen, /* Length of buffer */ -SK_U32 NetIndex) /* NetIndex (0..n), in single net mode always zero */ -{ -SK_I32 Mode; /* Store value of subcommand. */ -SK_U32 Oid; /* Store value of OID. */ -int ReturnCode; /* Store return value to show status of PNMI action. */ -int HeaderLength; /* Length of desired action plus OID. */ - - ReturnCode = SK_PNMI_ERR_GENERAL; - - SK_MEMCPY(&Mode, pBuf, sizeof(SK_I32)); - SK_MEMCPY(&Oid, (char *) pBuf + sizeof(SK_I32), sizeof(SK_U32)); - HeaderLength = sizeof(SK_I32) + sizeof(SK_U32); - *pLen = *pLen - HeaderLength; - SK_MEMCPY((char *) pBuf + sizeof(SK_I32), (char *) pBuf + HeaderLength, *pLen); - - switch(Mode) { - case SK_GET_SINGLE_VAR: - ReturnCode = SkPnmiGetVar(pAC, IoC, Oid, - (char *) pBuf + sizeof(SK_I32), pLen, - ((SK_U32) (-1)), NetIndex); - SK_PNMI_STORE_U32(pBuf, ReturnCode); - *pLen = *pLen + sizeof(SK_I32); - break; - case SK_PRESET_SINGLE_VAR: - ReturnCode = SkPnmiPreSetVar(pAC, IoC, Oid, - (char *) pBuf + sizeof(SK_I32), pLen, - ((SK_U32) (-1)), NetIndex); - SK_PNMI_STORE_U32(pBuf, ReturnCode); - *pLen = *pLen + sizeof(SK_I32); - break; - case SK_SET_SINGLE_VAR: - ReturnCode = SkPnmiSetVar(pAC, IoC, Oid, - (char *) pBuf + sizeof(SK_I32), pLen, - ((SK_U32) (-1)), NetIndex); - SK_PNMI_STORE_U32(pBuf, ReturnCode); - *pLen = *pLen + sizeof(SK_I32); - break; - case SK_GET_FULL_MIB: - ReturnCode = SkPnmiGetStruct(pAC, IoC, pBuf, pLen, NetIndex); - break; - case SK_PRESET_FULL_MIB: - ReturnCode = SkPnmiPreSetStruct(pAC, IoC, pBuf, pLen, NetIndex); - break; - case SK_SET_FULL_MIB: - ReturnCode = SkPnmiSetStruct(pAC, IoC, pBuf, pLen, NetIndex); - break; - default: - break; - } - - return (ReturnCode); - -} /* SkGeIocGen */ diff --git a/drivers/net/sk98lin/skgesirq.c b/drivers/net/sk98lin/skgesirq.c deleted file mode 100644 index 3e7aa49afd00..000000000000 --- a/drivers/net/sk98lin/skgesirq.c +++ /dev/null @@ -1,2229 +0,0 @@ -/****************************************************************************** - * - * Name: skgesirq.c - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.92 $ - * Date: $Date: 2003/09/16 14:37:07 $ - * Purpose: Special IRQ module - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * Special Interrupt handler - * - * The following abstract should show how this module is included - * in the driver path: - * - * In the ISR of the driver the bits for frame transmission complete and - * for receive complete are checked and handled by the driver itself. - * The bits of the slow path mask are checked after that and then the - * entry into the so-called "slow path" is prepared. It is an implementors - * decision whether this is executed directly or just scheduled by - * disabling the mask. In the interrupt service routine some events may be - * generated, so it would be a good idea to call the EventDispatcher - * right after this ISR. - * - * The Interrupt source register of the adapter is NOT read by this module. - * SO if the drivers implementor needs a while loop around the - * slow data paths interrupt bits, he needs to call the SkGeSirqIsr() for - * each loop entered. - * - * However, the MAC Interrupt status registers are read in a while loop. - * - */ - -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: skgesirq.c,v 1.92 2003/09/16 14:37:07 rschmidt Exp $ (C) Marvell."; -#endif - -#include "h/skdrv1st.h" /* Driver Specific Definitions */ -#ifndef SK_SLIM -#include "h/skgepnmi.h" /* PNMI Definitions */ -#include "h/skrlmt.h" /* RLMT Definitions */ -#endif -#include "h/skdrv2nd.h" /* Adapter Control and Driver specific Def. */ - -/* local function prototypes */ -#ifdef GENESIS -static int SkGePortCheckUpXmac(SK_AC*, SK_IOC, int, SK_BOOL); -static int SkGePortCheckUpBcom(SK_AC*, SK_IOC, int, SK_BOOL); -static void SkPhyIsrBcom(SK_AC*, SK_IOC, int, SK_U16); -#endif /* GENESIS */ -#ifdef YUKON -static int SkGePortCheckUpGmac(SK_AC*, SK_IOC, int, SK_BOOL); -static void SkPhyIsrGmac(SK_AC*, SK_IOC, int, SK_U16); -#endif /* YUKON */ -#ifdef OTHER_PHY -static int SkGePortCheckUpLone(SK_AC*, SK_IOC, int, SK_BOOL); -static int SkGePortCheckUpNat(SK_AC*, SK_IOC, int, SK_BOOL); -static void SkPhyIsrLone(SK_AC*, SK_IOC, int, SK_U16); -#endif /* OTHER_PHY */ - -#ifdef GENESIS -/* - * array of Rx counter from XMAC which are checked - * in AutoSense mode to check whether a link is not able to auto-negotiate. - */ -static const SK_U16 SkGeRxRegs[]= { - XM_RXF_64B, - XM_RXF_127B, - XM_RXF_255B, - XM_RXF_511B, - XM_RXF_1023B, - XM_RXF_MAX_SZ -} ; -#endif /* GENESIS */ - -#ifdef __C2MAN__ -/* - * Special IRQ function - * - * General Description: - * - */ -intro() -{} -#endif - -/****************************************************************************** - * - * SkHWInitDefSense() - Default Autosensing mode initialization - * - * Description: sets the PLinkMode for HWInit - * - * Returns: N/A - */ -static void SkHWInitDefSense( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - - pPrt = &pAC->GIni.GP[Port]; - - pPrt->PAutoNegTimeOut = 0; - - if (pPrt->PLinkModeConf != SK_LMODE_AUTOSENSE) { - pPrt->PLinkMode = pPrt->PLinkModeConf; - return; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("AutoSensing: First mode %d on Port %d\n", - (int)SK_LMODE_AUTOFULL, Port)); - - pPrt->PLinkMode = (SK_U8)SK_LMODE_AUTOFULL; - - return; -} /* SkHWInitDefSense */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkHWSenseGetNext() - Get Next Autosensing Mode - * - * Description: gets the appropriate next mode - * - * Note: - * - */ -static SK_U8 SkHWSenseGetNext( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - - pPrt = &pAC->GIni.GP[Port]; - - pPrt->PAutoNegTimeOut = 0; - - if (pPrt->PLinkModeConf != (SK_U8)SK_LMODE_AUTOSENSE) { - /* Leave all as configured */ - return(pPrt->PLinkModeConf); - } - - if (pPrt->PLinkMode == (SK_U8)SK_LMODE_AUTOFULL) { - /* Return next mode AUTOBOTH */ - return ((SK_U8)SK_LMODE_AUTOBOTH); - } - - /* Return default autofull */ - return ((SK_U8)SK_LMODE_AUTOFULL); -} /* SkHWSenseGetNext */ - - -/****************************************************************************** - * - * SkHWSenseSetNext() - Autosensing Set next mode - * - * Description: sets the appropriate next mode - * - * Returns: N/A - */ -static void SkHWSenseSetNext( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_U8 NewMode) /* New Mode to be written in sense mode */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - - pPrt = &pAC->GIni.GP[Port]; - - pPrt->PAutoNegTimeOut = 0; - - if (pPrt->PLinkModeConf != (SK_U8)SK_LMODE_AUTOSENSE) { - return; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("AutoSensing: next mode %d on Port %d\n", - (int)NewMode, Port)); - - pPrt->PLinkMode = NewMode; - - return; -} /* SkHWSenseSetNext */ -#endif /* GENESIS */ - - -/****************************************************************************** - * - * SkHWLinkDown() - Link Down handling - * - * Description: handles the hardware link down signal - * - * Returns: N/A - */ -void SkHWLinkDown( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - - pPrt = &pAC->GIni.GP[Port]; - - /* Disable all MAC interrupts */ - SkMacIrqDisable(pAC, IoC, Port); - - /* Disable Receiver and Transmitter */ - SkMacRxTxDisable(pAC, IoC, Port); - - /* Init default sense mode */ - SkHWInitDefSense(pAC, IoC, Port); - - if (pPrt->PHWLinkUp == SK_FALSE) { - return; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Link down Port %d\n", Port)); - - /* Set Link to DOWN */ - pPrt->PHWLinkUp = SK_FALSE; - - /* Reset Port stati */ - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_UNKNOWN; - pPrt->PFlowCtrlStatus = (SK_U8)SK_FLOW_STAT_NONE; - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_INDETERMINATED; - - /* Re-init Phy especially when the AutoSense default is set now */ - SkMacInitPhy(pAC, IoC, Port, SK_FALSE); - - /* GP0: used for workaround of Rev. C Errata 2 */ - - /* Do NOT signal to RLMT */ - - /* Do NOT start the timer here */ -} /* SkHWLinkDown */ - - -/****************************************************************************** - * - * SkHWLinkUp() - Link Up handling - * - * Description: handles the hardware link up signal - * - * Returns: N/A - */ -static void SkHWLinkUp( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PHWLinkUp) { - /* We do NOT need to proceed on active link */ - return; - } - - pPrt->PHWLinkUp = SK_TRUE; - pPrt->PAutoNegFail = SK_FALSE; - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_UNKNOWN; - - if (pPrt->PLinkMode != (SK_U8)SK_LMODE_AUTOHALF && - pPrt->PLinkMode != (SK_U8)SK_LMODE_AUTOFULL && - pPrt->PLinkMode != (SK_U8)SK_LMODE_AUTOBOTH) { - /* Link is up and no Auto-negotiation should be done */ - - /* Link speed should be the configured one */ - switch (pPrt->PLinkSpeed) { - case SK_LSPEED_AUTO: - /* default is 1000 Mbps */ - case SK_LSPEED_1000MBPS: - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_1000MBPS; - break; - case SK_LSPEED_100MBPS: - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_100MBPS; - break; - case SK_LSPEED_10MBPS: - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_10MBPS; - break; - } - - /* Set Link Mode Status */ - if (pPrt->PLinkMode == SK_LMODE_FULL) { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_FULL; - } - else { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_HALF; - } - - /* No flow control without auto-negotiation */ - pPrt->PFlowCtrlStatus = (SK_U8)SK_FLOW_STAT_NONE; - - /* enable Rx/Tx */ - (void)SkMacRxTxEnable(pAC, IoC, Port); - } -} /* SkHWLinkUp */ - - -/****************************************************************************** - * - * SkMacParity() - MAC parity workaround - * - * Description: handles MAC parity errors correctly - * - * Returns: N/A - */ -static void SkMacParity( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index of the port failed */ -{ - SK_EVPARA Para; - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - SK_U32 TxMax; /* Tx Max Size Counter */ - - pPrt = &pAC->GIni.GP[Port]; - - /* Clear IRQ Tx Parity Error */ -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - SK_OUT16(IoC, MR_ADDR(Port, TX_MFF_CTRL1), MFF_CLR_PERR); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* HW-Bug #8: cleared by GMF_CLI_TX_FC instead of GMF_CLI_TX_PE */ - SK_OUT8(IoC, MR_ADDR(Port, TX_GMF_CTRL_T), - (SK_U8)((pAC->GIni.GIChipId == CHIP_ID_YUKON && - pAC->GIni.GIChipRev == 0) ? GMF_CLI_TX_FC : GMF_CLI_TX_PE)); - } -#endif /* YUKON */ - - if (pPrt->PCheckPar) { - - if (Port == MAC_1) { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E016, SKERR_SIRQ_E016MSG); - } - else { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E017, SKERR_SIRQ_E017MSG); - } - Para.Para64 = Port; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - - Para.Para32[0] = Port; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - - return; - } - - /* Check whether frames with a size of 1k were sent */ -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* Snap statistic counters */ - (void)SkXmUpdateStats(pAC, IoC, Port); - - (void)SkXmMacStatistic(pAC, IoC, Port, XM_TXF_MAX_SZ, &TxMax); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - (void)SkGmMacStatistic(pAC, IoC, Port, GM_TXF_1518B, &TxMax); - } -#endif /* YUKON */ - - if (TxMax > 0) { - /* From now on check the parity */ - pPrt->PCheckPar = SK_TRUE; - } -} /* SkMacParity */ - - -/****************************************************************************** - * - * SkGeHwErr() - Hardware Error service routine - * - * Description: handles all HW Error interrupts - * - * Returns: N/A - */ -static void SkGeHwErr( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -SK_U32 HwStatus) /* Interrupt status word */ -{ - SK_EVPARA Para; - SK_U16 Word; - - if ((HwStatus & (IS_IRQ_MST_ERR | IS_IRQ_STAT)) != 0) { - /* PCI Errors occured */ - if ((HwStatus & IS_IRQ_STAT) != 0) { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E013, SKERR_SIRQ_E013MSG); - } - else { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E012, SKERR_SIRQ_E012MSG); - } - - /* Reset all bits in the PCI STATUS register */ - SK_IN16(IoC, PCI_C(PCI_STATUS), &Word); - - SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_ON); - SK_OUT16(IoC, PCI_C(PCI_STATUS), (SK_U16)(Word | PCI_ERRBITS)); - SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_OFF); - - Para.Para64 = 0; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_ADAP_FAIL, Para); - } - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - if ((HwStatus & IS_NO_STAT_M1) != 0) { - /* Ignore it */ - /* This situation is also indicated in the descriptor */ - SK_OUT16(IoC, MR_ADDR(MAC_1, RX_MFF_CTRL1), MFF_CLR_INSTAT); - } - - if ((HwStatus & IS_NO_STAT_M2) != 0) { - /* Ignore it */ - /* This situation is also indicated in the descriptor */ - SK_OUT16(IoC, MR_ADDR(MAC_2, RX_MFF_CTRL1), MFF_CLR_INSTAT); - } - - if ((HwStatus & IS_NO_TIST_M1) != 0) { - /* Ignore it */ - /* This situation is also indicated in the descriptor */ - SK_OUT16(IoC, MR_ADDR(MAC_1, RX_MFF_CTRL1), MFF_CLR_INTIST); - } - - if ((HwStatus & IS_NO_TIST_M2) != 0) { - /* Ignore it */ - /* This situation is also indicated in the descriptor */ - SK_OUT16(IoC, MR_ADDR(MAC_2, RX_MFF_CTRL1), MFF_CLR_INTIST); - } - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* This is necessary only for Rx timing measurements */ - if ((HwStatus & IS_IRQ_TIST_OV) != 0) { - /* increment Time Stamp Timer counter (high) */ - pAC->GIni.GITimeStampCnt++; - - /* Clear Time Stamp Timer IRQ */ - SK_OUT8(IoC, GMAC_TI_ST_CTRL, (SK_U8)GMT_ST_CLR_IRQ); - } - - if ((HwStatus & IS_IRQ_SENSOR) != 0) { - /* no sensors on 32-bit Yukon */ - if (pAC->GIni.GIYukon32Bit) { - /* disable HW Error IRQ */ - pAC->GIni.GIValIrqMask &= ~IS_HW_ERR; - } - } - } -#endif /* YUKON */ - - if ((HwStatus & IS_RAM_RD_PAR) != 0) { - SK_OUT16(IoC, B3_RI_CTRL, RI_CLR_RD_PERR); - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E014, SKERR_SIRQ_E014MSG); - Para.Para64 = 0; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_ADAP_FAIL, Para); - } - - if ((HwStatus & IS_RAM_WR_PAR) != 0) { - SK_OUT16(IoC, B3_RI_CTRL, RI_CLR_WR_PERR); - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E015, SKERR_SIRQ_E015MSG); - Para.Para64 = 0; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_ADAP_FAIL, Para); - } - - if ((HwStatus & IS_M1_PAR_ERR) != 0) { - SkMacParity(pAC, IoC, MAC_1); - } - - if ((HwStatus & IS_M2_PAR_ERR) != 0) { - SkMacParity(pAC, IoC, MAC_2); - } - - if ((HwStatus & IS_R1_PAR_ERR) != 0) { - /* Clear IRQ */ - SK_OUT32(IoC, B0_R1_CSR, CSR_IRQ_CL_P); - - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E018, SKERR_SIRQ_E018MSG); - Para.Para64 = MAC_1; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - - Para.Para32[0] = MAC_1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - - if ((HwStatus & IS_R2_PAR_ERR) != 0) { - /* Clear IRQ */ - SK_OUT32(IoC, B0_R2_CSR, CSR_IRQ_CL_P); - - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E019, SKERR_SIRQ_E019MSG); - Para.Para64 = MAC_2; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - - Para.Para32[0] = MAC_2; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } -} /* SkGeHwErr */ - - -/****************************************************************************** - * - * SkGeSirqIsr() - Special Interrupt Service Routine - * - * Description: handles all non data transfer specific interrupts (slow path) - * - * Returns: N/A - */ -void SkGeSirqIsr( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -SK_U32 Istatus) /* Interrupt status word */ -{ - SK_EVPARA Para; - SK_U32 RegVal32; /* Read register value */ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - SK_U16 PhyInt; - int i; - - if (((Istatus & IS_HW_ERR) & pAC->GIni.GIValIrqMask) != 0) { - /* read the HW Error Interrupt source */ - SK_IN32(IoC, B0_HWE_ISRC, &RegVal32); - - SkGeHwErr(pAC, IoC, RegVal32); - } - - /* - * Packet Timeout interrupts - */ - /* Check whether MACs are correctly initialized */ - if (((Istatus & (IS_PA_TO_RX1 | IS_PA_TO_TX1)) != 0) && - pAC->GIni.GP[MAC_1].PState == SK_PRT_RESET) { - /* MAC 1 was not initialized but Packet timeout occured */ - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_SIRQ_E004, - SKERR_SIRQ_E004MSG); - } - - if (((Istatus & (IS_PA_TO_RX2 | IS_PA_TO_TX2)) != 0) && - pAC->GIni.GP[MAC_2].PState == SK_PRT_RESET) { - /* MAC 2 was not initialized but Packet timeout occured */ - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_SIRQ_E005, - SKERR_SIRQ_E005MSG); - } - - if ((Istatus & IS_PA_TO_RX1) != 0) { - /* Means network is filling us up */ - SK_ERR_LOG(pAC, SK_ERRCL_HW | SK_ERRCL_INIT, SKERR_SIRQ_E002, - SKERR_SIRQ_E002MSG); - SK_OUT16(IoC, B3_PA_CTRL, PA_CLR_TO_RX1); - } - - if ((Istatus & IS_PA_TO_RX2) != 0) { - /* Means network is filling us up */ - SK_ERR_LOG(pAC, SK_ERRCL_HW | SK_ERRCL_INIT, SKERR_SIRQ_E003, - SKERR_SIRQ_E003MSG); - SK_OUT16(IoC, B3_PA_CTRL, PA_CLR_TO_RX2); - } - - if ((Istatus & IS_PA_TO_TX1) != 0) { - - pPrt = &pAC->GIni.GP[0]; - - /* May be a normal situation in a server with a slow network */ - SK_OUT16(IoC, B3_PA_CTRL, PA_CLR_TO_TX1); - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* - * workaround: if in half duplex mode, check for Tx hangup. - * Read number of TX'ed bytes, wait for 10 ms, then compare - * the number with current value. If nothing changed, we assume - * that Tx is hanging and do a FIFO flush (see event routine). - */ - if ((pPrt->PLinkModeStatus == SK_LMODE_STAT_HALF || - pPrt->PLinkModeStatus == SK_LMODE_STAT_AUTOHALF) && - !pPrt->HalfDupTimerActive) { - /* - * many more pack. arb. timeouts may come in between, - * we ignore those - */ - pPrt->HalfDupTimerActive = SK_TRUE; - /* Snap statistic counters */ - (void)SkXmUpdateStats(pAC, IoC, 0); - - (void)SkXmMacStatistic(pAC, IoC, 0, XM_TXO_OK_HI, &RegVal32); - - pPrt->LastOctets = (SK_U64)RegVal32 << 32; - - (void)SkXmMacStatistic(pAC, IoC, 0, XM_TXO_OK_LO, &RegVal32); - - pPrt->LastOctets += RegVal32; - - Para.Para32[0] = 0; - SkTimerStart(pAC, IoC, &pPrt->HalfDupChkTimer, SK_HALFDUP_CHK_TIME, - SKGE_HWAC, SK_HWEV_HALFDUP_CHK, Para); - } - } -#endif /* GENESIS */ - } - - if ((Istatus & IS_PA_TO_TX2) != 0) { - - pPrt = &pAC->GIni.GP[1]; - - /* May be a normal situation in a server with a slow network */ - SK_OUT16(IoC, B3_PA_CTRL, PA_CLR_TO_TX2); - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* workaround: see above */ - if ((pPrt->PLinkModeStatus == SK_LMODE_STAT_HALF || - pPrt->PLinkModeStatus == SK_LMODE_STAT_AUTOHALF) && - !pPrt->HalfDupTimerActive) { - pPrt->HalfDupTimerActive = SK_TRUE; - /* Snap statistic counters */ - (void)SkXmUpdateStats(pAC, IoC, 1); - - (void)SkXmMacStatistic(pAC, IoC, 1, XM_TXO_OK_HI, &RegVal32); - - pPrt->LastOctets = (SK_U64)RegVal32 << 32; - - (void)SkXmMacStatistic(pAC, IoC, 1, XM_TXO_OK_LO, &RegVal32); - - pPrt->LastOctets += RegVal32; - - Para.Para32[0] = 1; - SkTimerStart(pAC, IoC, &pPrt->HalfDupChkTimer, SK_HALFDUP_CHK_TIME, - SKGE_HWAC, SK_HWEV_HALFDUP_CHK, Para); - } - } -#endif /* GENESIS */ - } - - /* Check interrupts of the particular queues */ - if ((Istatus & IS_R1_C) != 0) { - /* Clear IRQ */ - SK_OUT32(IoC, B0_R1_CSR, CSR_IRQ_CL_C); - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_SIRQ_E006, - SKERR_SIRQ_E006MSG); - Para.Para64 = MAC_1; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - Para.Para32[0] = MAC_1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - - if ((Istatus & IS_R2_C) != 0) { - /* Clear IRQ */ - SK_OUT32(IoC, B0_R2_CSR, CSR_IRQ_CL_C); - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_SIRQ_E007, - SKERR_SIRQ_E007MSG); - Para.Para64 = MAC_2; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - Para.Para32[0] = MAC_2; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - - if ((Istatus & IS_XS1_C) != 0) { - /* Clear IRQ */ - SK_OUT32(IoC, B0_XS1_CSR, CSR_IRQ_CL_C); - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_SIRQ_E008, - SKERR_SIRQ_E008MSG); - Para.Para64 = MAC_1; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - Para.Para32[0] = MAC_1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - - if ((Istatus & IS_XA1_C) != 0) { - /* Clear IRQ */ - SK_OUT32(IoC, B0_XA1_CSR, CSR_IRQ_CL_C); - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_SIRQ_E009, - SKERR_SIRQ_E009MSG); - Para.Para64 = MAC_1; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - Para.Para32[0] = MAC_1; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - - if ((Istatus & IS_XS2_C) != 0) { - /* Clear IRQ */ - SK_OUT32(IoC, B0_XS2_CSR, CSR_IRQ_CL_C); - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_SIRQ_E010, - SKERR_SIRQ_E010MSG); - Para.Para64 = MAC_2; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - Para.Para32[0] = MAC_2; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - - if ((Istatus & IS_XA2_C) != 0) { - /* Clear IRQ */ - SK_OUT32(IoC, B0_XA2_CSR, CSR_IRQ_CL_C); - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_SIRQ_E011, - SKERR_SIRQ_E011MSG); - Para.Para64 = MAC_2; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); - Para.Para32[0] = MAC_2; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - - /* External reg interrupt */ - if ((Istatus & IS_EXT_REG) != 0) { - /* Test IRQs from PHY */ - for (i = 0; i < pAC->GIni.GIMacsFound; i++) { - - pPrt = &pAC->GIni.GP[i]; - - if (pPrt->PState == SK_PRT_RESET) { - continue; - } - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - switch (pPrt->PhyType) { - - case SK_PHY_XMAC: - break; - - case SK_PHY_BCOM: - SkXmPhyRead(pAC, IoC, i, PHY_BCOM_INT_STAT, &PhyInt); - - if ((PhyInt & ~PHY_B_DEF_MSK) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Port %d Bcom Int: 0x%04X\n", - i, PhyInt)); - SkPhyIsrBcom(pAC, IoC, i, PhyInt); - } - break; -#ifdef OTHER_PHY - case SK_PHY_LONE: - SkXmPhyRead(pAC, IoC, i, PHY_LONE_INT_STAT, &PhyInt); - - if ((PhyInt & PHY_L_DEF_MSK) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Port %d Lone Int: %x\n", - i, PhyInt)); - SkPhyIsrLone(pAC, IoC, i, PhyInt); - } - break; -#endif /* OTHER_PHY */ - } - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* Read PHY Interrupt Status */ - SkGmPhyRead(pAC, IoC, i, PHY_MARV_INT_STAT, &PhyInt); - - if ((PhyInt & PHY_M_DEF_MSK) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Port %d Marv Int: 0x%04X\n", - i, PhyInt)); - SkPhyIsrGmac(pAC, IoC, i, PhyInt); - } - } -#endif /* YUKON */ - } - } - - /* I2C Ready interrupt */ - if ((Istatus & IS_I2C_READY) != 0) { -#ifdef SK_SLIM - SK_OUT32(IoC, B2_I2C_IRQ, I2C_CLR_IRQ); -#else - SkI2cIsr(pAC, IoC); -#endif - } - - /* SW forced interrupt */ - if ((Istatus & IS_IRQ_SW) != 0) { - /* clear the software IRQ */ - SK_OUT8(IoC, B0_CTST, CS_CL_SW_IRQ); - } - - if ((Istatus & IS_LNK_SYNC_M1) != 0) { - /* - * We do NOT need the Link Sync interrupt, because it shows - * us only a link going down. - */ - /* clear interrupt */ - SK_OUT8(IoC, MR_ADDR(MAC_1, LNK_SYNC_CTRL), LED_CLR_IRQ); - } - - /* Check MAC after link sync counter */ - if ((Istatus & IS_MAC1) != 0) { - /* IRQ from MAC 1 */ - SkMacIrq(pAC, IoC, MAC_1); - } - - if ((Istatus & IS_LNK_SYNC_M2) != 0) { - /* - * We do NOT need the Link Sync interrupt, because it shows - * us only a link going down. - */ - /* clear interrupt */ - SK_OUT8(IoC, MR_ADDR(MAC_2, LNK_SYNC_CTRL), LED_CLR_IRQ); - } - - /* Check MAC after link sync counter */ - if ((Istatus & IS_MAC2) != 0) { - /* IRQ from MAC 2 */ - SkMacIrq(pAC, IoC, MAC_2); - } - - /* Timer interrupt (served last) */ - if ((Istatus & IS_TIMINT) != 0) { - /* check for HW Errors */ - if (((Istatus & IS_HW_ERR) & ~pAC->GIni.GIValIrqMask) != 0) { - /* read the HW Error Interrupt source */ - SK_IN32(IoC, B0_HWE_ISRC, &RegVal32); - - SkGeHwErr(pAC, IoC, RegVal32); - } - - SkHwtIsr(pAC, IoC); - } - -} /* SkGeSirqIsr */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkGePortCheckShorts() - Implementing XMAC Workaround Errata # 2 - * - * return: - * 0 o.k. nothing needed - * 1 Restart needed on this port - */ -static int SkGePortCheckShorts( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO Context */ -int Port) /* Which port should be checked */ -{ - SK_U32 Shorts; /* Short Event Counter */ - SK_U32 CheckShorts; /* Check value for Short Event Counter */ - SK_U64 RxCts; /* Rx Counter (packets on network) */ - SK_U32 RxTmp; /* Rx temp. Counter */ - SK_U32 FcsErrCts; /* FCS Error Counter */ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - int Rtv; /* Return value */ - int i; - - pPrt = &pAC->GIni.GP[Port]; - - /* Default: no action */ - Rtv = SK_HW_PS_NONE; - - (void)SkXmUpdateStats(pAC, IoC, Port); - - /* Extra precaution: check for short Event counter */ - (void)SkXmMacStatistic(pAC, IoC, Port, XM_RXE_SHT_ERR, &Shorts); - - /* - * Read Rx counters (packets seen on the network and not necessarily - * really received. - */ - RxCts = 0; - - for (i = 0; i < sizeof(SkGeRxRegs)/sizeof(SkGeRxRegs[0]); i++) { - - (void)SkXmMacStatistic(pAC, IoC, Port, SkGeRxRegs[i], &RxTmp); - - RxCts += (SK_U64)RxTmp; - } - - /* On default: check shorts against zero */ - CheckShorts = 0; - - /* Extra precaution on active links */ - if (pPrt->PHWLinkUp) { - /* Reset Link Restart counter */ - pPrt->PLinkResCt = 0; - pPrt->PAutoNegTOCt = 0; - - /* If link is up check for 2 */ - CheckShorts = 2; - - (void)SkXmMacStatistic(pAC, IoC, Port, XM_RXF_FCS_ERR, &FcsErrCts); - - if (pPrt->PLinkModeConf == SK_LMODE_AUTOSENSE && - pPrt->PLipaAutoNeg == SK_LIPA_UNKNOWN && - (pPrt->PLinkMode == SK_LMODE_HALF || - pPrt->PLinkMode == SK_LMODE_FULL)) { - /* - * This is autosensing and we are in the fallback - * manual full/half duplex mode. - */ - if (RxCts == pPrt->PPrevRx) { - /* Nothing received, restart link */ - pPrt->PPrevFcs = FcsErrCts; - pPrt->PPrevShorts = Shorts; - - return(SK_HW_PS_RESTART); - } - else { - pPrt->PLipaAutoNeg = SK_LIPA_MANUAL; - } - } - - if (((RxCts - pPrt->PPrevRx) > pPrt->PRxLim) || - (!(FcsErrCts - pPrt->PPrevFcs))) { - /* - * Note: The compare with zero above has to be done the way shown, - * otherwise the Linux driver will have a problem. - */ - /* - * We received a bunch of frames or no CRC error occured on the - * network -> ok. - */ - pPrt->PPrevRx = RxCts; - pPrt->PPrevFcs = FcsErrCts; - pPrt->PPrevShorts = Shorts; - - return(SK_HW_PS_NONE); - } - - pPrt->PPrevFcs = FcsErrCts; - } - - - if ((Shorts - pPrt->PPrevShorts) > CheckShorts) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Short Event Count Restart Port %d \n", Port)); - Rtv = SK_HW_PS_RESTART; - } - - pPrt->PPrevShorts = Shorts; - pPrt->PPrevRx = RxCts; - - return(Rtv); -} /* SkGePortCheckShorts */ -#endif /* GENESIS */ - - -/****************************************************************************** - * - * SkGePortCheckUp() - Check if the link is up - * - * return: - * 0 o.k. nothing needed - * 1 Restart needed on this port - * 2 Link came up - */ -static int SkGePortCheckUp( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO Context */ -int Port) /* Which port should be checked */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - SK_BOOL AutoNeg; /* Is Auto-negotiation used ? */ - int Rtv; /* Return value */ - - Rtv = SK_HW_PS_NONE; - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PLinkMode == SK_LMODE_HALF || pPrt->PLinkMode == SK_LMODE_FULL) { - AutoNeg = SK_FALSE; - } - else { - AutoNeg = SK_TRUE; - } - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - switch (pPrt->PhyType) { - - case SK_PHY_XMAC: - Rtv = SkGePortCheckUpXmac(pAC, IoC, Port, AutoNeg); - break; - case SK_PHY_BCOM: - Rtv = SkGePortCheckUpBcom(pAC, IoC, Port, AutoNeg); - break; -#ifdef OTHER_PHY - case SK_PHY_LONE: - Rtv = SkGePortCheckUpLone(pAC, IoC, Port, AutoNeg); - break; - case SK_PHY_NAT: - Rtv = SkGePortCheckUpNat(pAC, IoC, Port, AutoNeg); - break; -#endif /* OTHER_PHY */ - } - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - Rtv = SkGePortCheckUpGmac(pAC, IoC, Port, AutoNeg); - } -#endif /* YUKON */ - - return(Rtv); -} /* SkGePortCheckUp */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkGePortCheckUpXmac() - Implementing of the Workaround Errata # 2 - * - * return: - * 0 o.k. nothing needed - * 1 Restart needed on this port - * 2 Link came up - */ -static int SkGePortCheckUpXmac( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO Context */ -int Port, /* Which port should be checked */ -SK_BOOL AutoNeg) /* Is Auto-negotiation used ? */ -{ - SK_U32 Shorts; /* Short Event Counter */ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - int Done; - SK_U32 GpReg; /* General Purpose register value */ - SK_U16 Isrc; /* Interrupt source register */ - SK_U16 IsrcSum; /* Interrupt source register sum */ - SK_U16 LpAb; /* Link Partner Ability */ - SK_U16 ResAb; /* Resolved Ability */ - SK_U16 ExtStat; /* Extended Status Register */ - SK_U8 NextMode; /* Next AutoSensing Mode */ - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PHWLinkUp) { - if (pPrt->PhyType != SK_PHY_XMAC) { - return(SK_HW_PS_NONE); - } - else { - return(SkGePortCheckShorts(pAC, IoC, Port)); - } - } - - IsrcSum = pPrt->PIsave; - pPrt->PIsave = 0; - - /* Now wait for each port's link */ - if (pPrt->PLinkBroken) { - /* Link was broken */ - XM_IN32(IoC, Port, XM_GP_PORT, &GpReg); - - if ((GpReg & XM_GP_INP_ASS) == 0) { - /* The Link is in sync */ - XM_IN16(IoC, Port, XM_ISRC, &Isrc); - IsrcSum |= Isrc; - SkXmAutoNegLipaXmac(pAC, IoC, Port, IsrcSum); - - if ((Isrc & XM_IS_INP_ASS) == 0) { - /* It has been in sync since last time */ - /* Restart the PORT */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Link in sync Restart Port %d\n", Port)); - - (void)SkXmUpdateStats(pAC, IoC, Port); - - /* We now need to reinitialize the PrevShorts counter */ - (void)SkXmMacStatistic(pAC, IoC, Port, XM_RXE_SHT_ERR, &Shorts); - pPrt->PPrevShorts = Shorts; - - pPrt->PLinkBroken = SK_FALSE; - - /* - * Link Restart Workaround: - * it may be possible that the other Link side - * restarts its link as well an we detect - * another LinkBroken. To prevent this - * happening we check for a maximum number - * of consecutive restart. If those happens, - * we do NOT restart the active link and - * check whether the link is now o.k. - */ - pPrt->PLinkResCt++; - - pPrt->PAutoNegTimeOut = 0; - - if (pPrt->PLinkResCt < SK_MAX_LRESTART) { - return(SK_HW_PS_RESTART); - } - - pPrt->PLinkResCt = 0; - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Do NOT restart on Port %d %x %x\n", Port, Isrc, IsrcSum)); - } - else { - pPrt->PIsave = (SK_U16)(IsrcSum & XM_IS_AND); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Save Sync/nosync Port %d %x %x\n", Port, Isrc, IsrcSum)); - - /* Do nothing more if link is broken */ - return(SK_HW_PS_NONE); - } - } - else { - /* Do nothing more if link is broken */ - return(SK_HW_PS_NONE); - } - - } - else { - /* Link was not broken, check if it is */ - XM_IN16(IoC, Port, XM_ISRC, &Isrc); - IsrcSum |= Isrc; - if ((Isrc & XM_IS_INP_ASS) != 0) { - XM_IN16(IoC, Port, XM_ISRC, &Isrc); - IsrcSum |= Isrc; - if ((Isrc & XM_IS_INP_ASS) != 0) { - XM_IN16(IoC, Port, XM_ISRC, &Isrc); - IsrcSum |= Isrc; - if ((Isrc & XM_IS_INP_ASS) != 0) { - pPrt->PLinkBroken = SK_TRUE; - /* Re-Init Link partner Autoneg flag */ - pPrt->PLipaAutoNeg = SK_LIPA_UNKNOWN; - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Link broken Port %d\n", Port)); - - /* Cable removed-> reinit sense mode */ - SkHWInitDefSense(pAC, IoC, Port); - - return(SK_HW_PS_RESTART); - } - } - } - else { - SkXmAutoNegLipaXmac(pAC, IoC, Port, Isrc); - - if (SkGePortCheckShorts(pAC, IoC, Port) == SK_HW_PS_RESTART) { - return(SK_HW_PS_RESTART); - } - } - } - - /* - * here we usually can check whether the link is in sync and - * auto-negotiation is done. - */ - XM_IN32(IoC, Port, XM_GP_PORT, &GpReg); - XM_IN16(IoC, Port, XM_ISRC, &Isrc); - IsrcSum |= Isrc; - - SkXmAutoNegLipaXmac(pAC, IoC, Port, IsrcSum); - - if ((GpReg & XM_GP_INP_ASS) != 0 || (IsrcSum & XM_IS_INP_ASS) != 0) { - if ((GpReg & XM_GP_INP_ASS) == 0) { - /* Save Auto-negotiation Done interrupt only if link is in sync */ - pPrt->PIsave = (SK_U16)(IsrcSum & XM_IS_AND); - } -#ifdef DEBUG - if ((pPrt->PIsave & XM_IS_AND) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNeg done rescheduled Port %d\n", Port)); - } -#endif /* DEBUG */ - return(SK_HW_PS_NONE); - } - - if (AutoNeg) { - if ((IsrcSum & XM_IS_AND) != 0) { - SkHWLinkUp(pAC, IoC, Port); - Done = SkMacAutoNegDone(pAC, IoC, Port); - if (Done != SK_AND_OK) { - /* Get PHY parameters, for debugging only */ - SkXmPhyRead(pAC, IoC, Port, PHY_XMAC_AUNE_LP, &LpAb); - SkXmPhyRead(pAC, IoC, Port, PHY_XMAC_RES_ABI, &ResAb); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNeg FAIL Port %d (LpAb %x, ResAb %x)\n", - Port, LpAb, ResAb)); - - /* Try next possible mode */ - NextMode = SkHWSenseGetNext(pAC, IoC, Port); - SkHWLinkDown(pAC, IoC, Port); - if (Done == SK_AND_DUP_CAP) { - /* GoTo next mode */ - SkHWSenseSetNext(pAC, IoC, Port, NextMode); - } - - return(SK_HW_PS_RESTART); - } - /* - * Dummy Read extended status to prevent extra link down/ups - * (clear Page Received bit if set) - */ - SkXmPhyRead(pAC, IoC, Port, PHY_XMAC_AUNE_EXP, &ExtStat); - - return(SK_HW_PS_LINK); - } - - /* AutoNeg not done, but HW link is up. Check for timeouts */ - pPrt->PAutoNegTimeOut++; - if (pPrt->PAutoNegTimeOut >= SK_AND_MAX_TO) { - /* Increase the Timeout counter */ - pPrt->PAutoNegTOCt++; - - /* Timeout occured */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("AutoNeg timeout Port %d\n", Port)); - if (pPrt->PLinkModeConf == SK_LMODE_AUTOSENSE && - pPrt->PLipaAutoNeg != SK_LIPA_AUTO) { - /* Set Link manually up */ - SkHWSenseSetNext(pAC, IoC, Port, SK_LMODE_FULL); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Set manual full duplex Port %d\n", Port)); - } - - if (pPrt->PLinkModeConf == SK_LMODE_AUTOSENSE && - pPrt->PLipaAutoNeg == SK_LIPA_AUTO && - pPrt->PAutoNegTOCt >= SK_MAX_ANEG_TO) { - /* - * This is rather complicated. - * we need to check here whether the LIPA_AUTO - * we saw before is false alert. We saw at one - * switch ( SR8800) that on boot time it sends - * just one auto-neg packet and does no further - * auto-negotiation. - * Solution: we restart the autosensing after - * a few timeouts. - */ - pPrt->PAutoNegTOCt = 0; - pPrt->PLipaAutoNeg = SK_LIPA_UNKNOWN; - SkHWInitDefSense(pAC, IoC, Port); - } - - /* Do the restart */ - return(SK_HW_PS_RESTART); - } - } - else { - /* Link is up and we don't need more */ -#ifdef DEBUG - if (pPrt->PLipaAutoNeg == SK_LIPA_AUTO) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("ERROR: Lipa auto detected on port %d\n", Port)); - } -#endif /* DEBUG */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Link sync(GP), Port %d\n", Port)); - SkHWLinkUp(pAC, IoC, Port); - - /* - * Link sync (GP) and so assume a good connection. But if not received - * a bunch of frames received in a time slot (maybe broken tx cable) - * the port is restart. - */ - return(SK_HW_PS_LINK); - } - - return(SK_HW_PS_NONE); -} /* SkGePortCheckUpXmac */ - - -/****************************************************************************** - * - * SkGePortCheckUpBcom() - Check if the link is up on Bcom PHY - * - * return: - * 0 o.k. nothing needed - * 1 Restart needed on this port - * 2 Link came up - */ -static int SkGePortCheckUpBcom( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO Context */ -int Port, /* Which port should be checked */ -SK_BOOL AutoNeg) /* Is Auto-negotiation used ? */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - int Done; - SK_U16 Isrc; /* Interrupt source register */ - SK_U16 PhyStat; /* Phy Status Register */ - SK_U16 ResAb; /* Master/Slave resolution */ - SK_U16 Ctrl; /* Broadcom control flags */ -#ifdef DEBUG - SK_U16 LpAb; - SK_U16 ExtStat; -#endif /* DEBUG */ - - pPrt = &pAC->GIni.GP[Port]; - - /* Check for No HCD Link events (#10523) */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_INT_STAT, &Isrc); - -#ifdef xDEBUG - if ((Isrc & ~(PHY_B_IS_HCT | PHY_B_IS_LCT)) == - (PHY_B_IS_SCR_S_ER | PHY_B_IS_RRS_CHANGE | PHY_B_IS_LRS_CHANGE)) { - - SK_U32 Stat1, Stat2, Stat3; - - Stat1 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_INT_MASK, &Stat1); - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "CheckUp1 - Stat: %x, Mask: %x", - (void *)Isrc, - (void *)Stat1); - - Stat1 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_CTRL, &Stat1); - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_STAT, &Stat2); - Stat1 = Stat1 << 16 | Stat2; - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUNE_ADV, &Stat2); - Stat3 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUNE_LP, &Stat3); - Stat2 = Stat2 << 16 | Stat3; - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "Ctrl/Stat: %x, AN Adv/LP: %x", - (void *)Stat1, - (void *)Stat2); - - Stat1 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUNE_EXP, &Stat1); - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_EXT_STAT, &Stat2); - Stat1 = Stat1 << 16 | Stat2; - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_1000T_CTRL, &Stat2); - Stat3 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_1000T_STAT, &Stat3); - Stat2 = Stat2 << 16 | Stat3; - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "AN Exp/IEEE Ext: %x, 1000T Ctrl/Stat: %x", - (void *)Stat1, - (void *)Stat2); - - Stat1 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_P_EXT_CTRL, &Stat1); - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_P_EXT_STAT, &Stat2); - Stat1 = Stat1 << 16 | Stat2; - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, &Stat2); - Stat3 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUX_STAT, &Stat3); - Stat2 = Stat2 << 16 | Stat3; - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "PHY Ext Ctrl/Stat: %x, Aux Ctrl/Stat: %x", - (void *)Stat1, - (void *)Stat2); - } -#endif /* DEBUG */ - - if ((Isrc & (PHY_B_IS_NO_HDCL /* | PHY_B_IS_NO_HDC */)) != 0) { - /* - * Workaround BCom Errata: - * enable and disable loopback mode if "NO HCD" occurs. - */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_CTRL, &Ctrl); - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_CTRL, - (SK_U16)(Ctrl | PHY_CT_LOOP)); - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_CTRL, - (SK_U16)(Ctrl & ~PHY_CT_LOOP)); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("No HCD Link event, Port %d\n", Port)); -#ifdef xDEBUG - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "No HCD link event, port %d.", - (void *)Port, - (void *)NULL); -#endif /* DEBUG */ - } - - /* Not obsolete: link status bit is latched to 0 and autoclearing! */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_STAT, &PhyStat); - - if (pPrt->PHWLinkUp) { - return(SK_HW_PS_NONE); - } - -#ifdef xDEBUG - { - SK_U32 Stat1, Stat2, Stat3; - - Stat1 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_INT_MASK, &Stat1); - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "CheckUp1a - Stat: %x, Mask: %x", - (void *)Isrc, - (void *)Stat1); - - Stat1 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_CTRL, &Stat1); - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_STAT, &PhyStat); - Stat1 = Stat1 << 16 | PhyStat; - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUNE_ADV, &Stat2); - Stat3 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUNE_LP, &Stat3); - Stat2 = Stat2 << 16 | Stat3; - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "Ctrl/Stat: %x, AN Adv/LP: %x", - (void *)Stat1, - (void *)Stat2); - - Stat1 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUNE_EXP, &Stat1); - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_EXT_STAT, &Stat2); - Stat1 = Stat1 << 16 | Stat2; - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_1000T_CTRL, &Stat2); - Stat3 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_1000T_STAT, &ResAb); - Stat2 = Stat2 << 16 | ResAb; - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "AN Exp/IEEE Ext: %x, 1000T Ctrl/Stat: %x", - (void *)Stat1, - (void *)Stat2); - - Stat1 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_P_EXT_CTRL, &Stat1); - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_P_EXT_STAT, &Stat2); - Stat1 = Stat1 << 16 | Stat2; - Stat2 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, &Stat2); - Stat3 = 0; - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUX_STAT, &Stat3); - Stat2 = Stat2 << 16 | Stat3; - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "PHY Ext Ctrl/Stat: %x, Aux Ctrl/Stat: %x", - (void *)Stat1, - (void *)Stat2); - } -#endif /* DEBUG */ - - /* - * Here we usually can check whether the link is in sync and - * auto-negotiation is done. - */ - - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_STAT, &PhyStat); - - SkMacAutoNegLipaPhy(pAC, IoC, Port, PhyStat); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("CheckUp Port %d, PhyStat: 0x%04X\n", Port, PhyStat)); - - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_1000T_STAT, &ResAb); - - if ((ResAb & PHY_B_1000S_MSF) != 0) { - /* Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Master/Slave Fault port %d\n", Port)); - - pPrt->PAutoNegFail = SK_TRUE; - pPrt->PMSStatus = SK_MS_STAT_FAULT; - - return(SK_HW_PS_RESTART); - } - - if ((PhyStat & PHY_ST_LSYNC) == 0) { - return(SK_HW_PS_NONE); - } - - pPrt->PMSStatus = ((ResAb & PHY_B_1000S_MSR) != 0) ? - SK_MS_STAT_MASTER : SK_MS_STAT_SLAVE; - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Port %d, ResAb: 0x%04X\n", Port, ResAb)); - - if (AutoNeg) { - if ((PhyStat & PHY_ST_AN_OVER) != 0) { - - SkHWLinkUp(pAC, IoC, Port); - - Done = SkMacAutoNegDone(pAC, IoC, Port); - - if (Done != SK_AND_OK) { -#ifdef DEBUG - /* Get PHY parameters, for debugging only */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUNE_LP, &LpAb); - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_1000T_STAT, &ExtStat); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNeg FAIL Port %d (LpAb %x, 1000TStat %x)\n", - Port, LpAb, ExtStat)); -#endif /* DEBUG */ - return(SK_HW_PS_RESTART); - } - else { -#ifdef xDEBUG - /* Dummy read ISR to prevent extra link downs/ups */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_INT_STAT, &ExtStat); - - if ((ExtStat & ~(PHY_B_IS_HCT | PHY_B_IS_LCT)) != 0) { - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "CheckUp2 - Stat: %x", - (void *)ExtStat, - (void *)NULL); - } -#endif /* DEBUG */ - return(SK_HW_PS_LINK); - } - } - } - else { /* !AutoNeg */ - /* Link is up and we don't need more. */ -#ifdef DEBUG - if (pPrt->PLipaAutoNeg == SK_LIPA_AUTO) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("ERROR: Lipa auto detected on port %d\n", Port)); - } -#endif /* DEBUG */ - -#ifdef xDEBUG - /* Dummy read ISR to prevent extra link downs/ups */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_INT_STAT, &ExtStat); - - if ((ExtStat & ~(PHY_B_IS_HCT | PHY_B_IS_LCT)) != 0) { - CMSMPrintString( - pAC->pConfigTable, - MSG_TYPE_RUNTIME_INFO, - "CheckUp3 - Stat: %x", - (void *)ExtStat, - (void *)NULL); - } -#endif /* DEBUG */ - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Link sync(GP), Port %d\n", Port)); - SkHWLinkUp(pAC, IoC, Port); - - return(SK_HW_PS_LINK); - } - - return(SK_HW_PS_NONE); -} /* SkGePortCheckUpBcom */ -#endif /* GENESIS */ - - -#ifdef YUKON -/****************************************************************************** - * - * SkGePortCheckUpGmac() - Check if the link is up on Marvell PHY - * - * return: - * 0 o.k. nothing needed - * 1 Restart needed on this port - * 2 Link came up - */ -static int SkGePortCheckUpGmac( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO Context */ -int Port, /* Which port should be checked */ -SK_BOOL AutoNeg) /* Is Auto-negotiation used ? */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - int Done; - SK_U16 PhyIsrc; /* PHY Interrupt source */ - SK_U16 PhyStat; /* PPY Status */ - SK_U16 PhySpecStat;/* PHY Specific Status */ - SK_U16 ResAb; /* Master/Slave resolution */ - SK_EVPARA Para; -#ifdef DEBUG - SK_U16 Word; /* I/O helper */ -#endif /* DEBUG */ - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PHWLinkUp) { - return(SK_HW_PS_NONE); - } - - /* Read PHY Status */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_STAT, &PhyStat); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("CheckUp Port %d, PhyStat: 0x%04X\n", Port, PhyStat)); - - /* Read PHY Interrupt Status */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_INT_STAT, &PhyIsrc); - - if ((PhyIsrc & PHY_M_IS_AN_COMPL) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Auto-Negotiation Completed, PhyIsrc: 0x%04X\n", PhyIsrc)); - } - - if ((PhyIsrc & PHY_M_IS_LSP_CHANGE) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Link Speed Changed, PhyIsrc: 0x%04X\n", PhyIsrc)); - } - - SkMacAutoNegLipaPhy(pAC, IoC, Port, PhyStat); - - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_1000T_STAT, &ResAb); - - if ((ResAb & PHY_B_1000S_MSF) != 0) { - /* Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Master/Slave Fault port %d\n", Port)); - - pPrt->PAutoNegFail = SK_TRUE; - pPrt->PMSStatus = SK_MS_STAT_FAULT; - - return(SK_HW_PS_RESTART); - } - - /* Read PHY Specific Status */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_STAT, &PhySpecStat); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Phy1000BT: 0x%04X, PhySpecStat: 0x%04X\n", ResAb, PhySpecStat)); - -#ifdef DEBUG - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_AUNE_EXP, &Word); - - if ((PhyIsrc & PHY_M_IS_AN_PR) != 0 || (Word & PHY_ANE_RX_PG) != 0 || - (PhySpecStat & PHY_M_PS_PAGE_REC) != 0) { - /* Read PHY Next Page Link Partner */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_NEPG_LP, &Word); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Page Received, NextPage: 0x%04X\n", Word)); - } -#endif /* DEBUG */ - - if ((PhySpecStat & PHY_M_PS_LINK_UP) == 0) { - return(SK_HW_PS_NONE); - } - - if ((PhySpecStat & PHY_M_PS_DOWNS_STAT) != 0 || - (PhyIsrc & PHY_M_IS_DOWNSH_DET) != 0) { - /* Downshift detected */ - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E025, SKERR_SIRQ_E025MSG); - - Para.Para64 = Port; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_DOWNSHIFT_DET, Para); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Downshift detected, PhyIsrc: 0x%04X\n", PhyIsrc)); - } - - pPrt->PMSStatus = ((ResAb & PHY_B_1000S_MSR) != 0) ? - SK_MS_STAT_MASTER : SK_MS_STAT_SLAVE; - - pPrt->PCableLen = (SK_U8)((PhySpecStat & PHY_M_PS_CABLE_MSK) >> 7); - - if (AutoNeg) { - /* Auto-Negotiation Over ? */ - if ((PhyStat & PHY_ST_AN_OVER) != 0) { - - SkHWLinkUp(pAC, IoC, Port); - - Done = SkMacAutoNegDone(pAC, IoC, Port); - - if (Done != SK_AND_OK) { - return(SK_HW_PS_RESTART); - } - - return(SK_HW_PS_LINK); - } - } - else { /* !AutoNeg */ - /* Link is up and we don't need more */ -#ifdef DEBUG - if (pPrt->PLipaAutoNeg == SK_LIPA_AUTO) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("ERROR: Lipa auto detected on port %d\n", Port)); - } -#endif /* DEBUG */ - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Link sync, Port %d\n", Port)); - SkHWLinkUp(pAC, IoC, Port); - - return(SK_HW_PS_LINK); - } - - return(SK_HW_PS_NONE); -} /* SkGePortCheckUpGmac */ -#endif /* YUKON */ - - -#ifdef OTHER_PHY -/****************************************************************************** - * - * SkGePortCheckUpLone() - Check if the link is up on Level One PHY - * - * return: - * 0 o.k. nothing needed - * 1 Restart needed on this port - * 2 Link came up - */ -static int SkGePortCheckUpLone( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO Context */ -int Port, /* Which port should be checked */ -SK_BOOL AutoNeg) /* Is Auto-negotiation used ? */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - int Done; - SK_U16 Isrc; /* Interrupt source register */ - SK_U16 LpAb; /* Link Partner Ability */ - SK_U16 ExtStat; /* Extended Status Register */ - SK_U16 PhyStat; /* Phy Status Register */ - SK_U16 StatSum; - SK_U8 NextMode; /* Next AutoSensing Mode */ - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PHWLinkUp) { - return(SK_HW_PS_NONE); - } - - StatSum = pPrt->PIsave; - pPrt->PIsave = 0; - - /* - * here we usually can check whether the link is in sync and - * auto-negotiation is done. - */ - SkXmPhyRead(pAC, IoC, Port, PHY_LONE_STAT, &PhyStat); - StatSum |= PhyStat; - - SkMacAutoNegLipaPhy(pAC, IoC, Port, PhyStat); - - if ((PhyStat & PHY_ST_LSYNC) == 0) { - /* Save Auto-negotiation Done bit */ - pPrt->PIsave = (SK_U16)(StatSum & PHY_ST_AN_OVER); -#ifdef DEBUG - if ((pPrt->PIsave & PHY_ST_AN_OVER) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNeg done rescheduled Port %d\n", Port)); - } -#endif /* DEBUG */ - return(SK_HW_PS_NONE); - } - - if (AutoNeg) { - if ((StatSum & PHY_ST_AN_OVER) != 0) { - SkHWLinkUp(pAC, IoC, Port); - Done = SkMacAutoNegDone(pAC, IoC, Port); - if (Done != SK_AND_OK) { - /* Get PHY parameters, for debugging only */ - SkXmPhyRead(pAC, IoC, Port, PHY_LONE_AUNE_LP, &LpAb); - SkXmPhyRead(pAC, IoC, Port, PHY_LONE_1000T_STAT, &ExtStat); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNeg FAIL Port %d (LpAb %x, 1000TStat %x)\n", - Port, LpAb, ExtStat)); - - /* Try next possible mode */ - NextMode = SkHWSenseGetNext(pAC, IoC, Port); - SkHWLinkDown(pAC, IoC, Port); - if (Done == SK_AND_DUP_CAP) { - /* GoTo next mode */ - SkHWSenseSetNext(pAC, IoC, Port, NextMode); - } - - return(SK_HW_PS_RESTART); - - } - else { - /* - * Dummy Read interrupt status to prevent - * extra link down/ups - */ - SkXmPhyRead(pAC, IoC, Port, PHY_LONE_INT_STAT, &ExtStat); - return(SK_HW_PS_LINK); - } - } - - /* AutoNeg not done, but HW link is up. Check for timeouts */ - pPrt->PAutoNegTimeOut++; - if (pPrt->PAutoNegTimeOut >= SK_AND_MAX_TO) { - /* Timeout occured */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("AutoNeg timeout Port %d\n", Port)); - if (pPrt->PLinkModeConf == SK_LMODE_AUTOSENSE && - pPrt->PLipaAutoNeg != SK_LIPA_AUTO) { - /* Set Link manually up */ - SkHWSenseSetNext(pAC, IoC, Port, SK_LMODE_FULL); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Set manual full duplex Port %d\n", Port)); - } - - /* Do the restart */ - return(SK_HW_PS_RESTART); - } - } - else { - /* Link is up and we don't need more */ -#ifdef DEBUG - if (pPrt->PLipaAutoNeg == SK_LIPA_AUTO) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("ERROR: Lipa auto detected on port %d\n", Port)); - } -#endif /* DEBUG */ - - /* - * Dummy Read interrupt status to prevent - * extra link down/ups - */ - SkXmPhyRead(pAC, IoC, Port, PHY_LONE_INT_STAT, &ExtStat); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("Link sync(GP), Port %d\n", Port)); - SkHWLinkUp(pAC, IoC, Port); - - return(SK_HW_PS_LINK); - } - - return(SK_HW_PS_NONE); -} /* SkGePortCheckUpLone */ - - -/****************************************************************************** - * - * SkGePortCheckUpNat() - Check if the link is up on National PHY - * - * return: - * 0 o.k. nothing needed - * 1 Restart needed on this port - * 2 Link came up - */ -static int SkGePortCheckUpNat( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO Context */ -int Port, /* Which port should be checked */ -SK_BOOL AutoNeg) /* Is Auto-negotiation used ? */ -{ - /* todo: National */ - return(SK_HW_PS_NONE); -} /* SkGePortCheckUpNat */ -#endif /* OTHER_PHY */ - - -/****************************************************************************** - * - * SkGeSirqEvent() - Event Service Routine - * - * Description: - * - * Notes: - */ -int SkGeSirqEvent( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* Io Context */ -SK_U32 Event, /* Module specific Event */ -SK_EVPARA Para) /* Event specific Parameter */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - SK_U32 Port; - SK_U32 Val32; - int PortStat; - SK_U8 Val8; -#ifdef GENESIS - SK_U64 Octets; -#endif /* GENESIS */ - - Port = Para.Para32[0]; - pPrt = &pAC->GIni.GP[Port]; - - switch (Event) { - case SK_HWEV_WATIM: - if (pPrt->PState == SK_PRT_RESET) { - - PortStat = SK_HW_PS_NONE; - } - else { - /* Check whether port came up */ - PortStat = SkGePortCheckUp(pAC, IoC, (int)Port); - } - - switch (PortStat) { - case SK_HW_PS_RESTART: - if (pPrt->PHWLinkUp) { - /* Set Link to down */ - SkHWLinkDown(pAC, IoC, (int)Port); - - /* - * Signal directly to RLMT to ensure correct - * sequence of SWITCH and RESET event. - */ - SkRlmtEvent(pAC, IoC, SK_RLMT_LINK_DOWN, Para); - } - - /* Restart needed */ - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_RESET, Para); - break; - - case SK_HW_PS_LINK: - /* Signal to RLMT */ - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_UP, Para); - break; - } - - /* Start again the check Timer */ - if (pPrt->PHWLinkUp) { - Val32 = SK_WA_ACT_TIME; - } - else { - Val32 = SK_WA_INA_TIME; - } - - /* Todo: still needed for non-XMAC PHYs??? */ - /* Start workaround Errata #2 timer */ - SkTimerStart(pAC, IoC, &pPrt->PWaTimer, Val32, - SKGE_HWAC, SK_HWEV_WATIM, Para); - break; - - case SK_HWEV_PORT_START: - if (pPrt->PHWLinkUp) { - /* - * Signal directly to RLMT to ensure correct - * sequence of SWITCH and RESET event. - */ - SkRlmtEvent(pAC, IoC, SK_RLMT_LINK_DOWN, Para); - } - - SkHWLinkDown(pAC, IoC, (int)Port); - - /* Schedule Port RESET */ - SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_RESET, Para); - - /* Start workaround Errata #2 timer */ - SkTimerStart(pAC, IoC, &pPrt->PWaTimer, SK_WA_INA_TIME, - SKGE_HWAC, SK_HWEV_WATIM, Para); - break; - - case SK_HWEV_PORT_STOP: - if (pPrt->PHWLinkUp) { - /* - * Signal directly to RLMT to ensure correct - * sequence of SWITCH and RESET event. - */ - SkRlmtEvent(pAC, IoC, SK_RLMT_LINK_DOWN, Para); - } - - /* Stop Workaround Timer */ - SkTimerStop(pAC, IoC, &pPrt->PWaTimer); - - SkHWLinkDown(pAC, IoC, (int)Port); - break; - - case SK_HWEV_UPDATE_STAT: - /* We do NOT need to update any statistics */ - break; - - case SK_HWEV_CLEAR_STAT: - /* We do NOT need to clear any statistics */ - for (Port = 0; Port < (SK_U32)pAC->GIni.GIMacsFound; Port++) { - pPrt->PPrevRx = 0; - pPrt->PPrevFcs = 0; - pPrt->PPrevShorts = 0; - } - break; - - case SK_HWEV_SET_LMODE: - Val8 = (SK_U8)Para.Para32[1]; - if (pPrt->PLinkModeConf != Val8) { - /* Set New link mode */ - pPrt->PLinkModeConf = Val8; - - /* Restart Port */ - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_STOP, Para); - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_START, Para); - } - break; - - case SK_HWEV_SET_FLOWMODE: - Val8 = (SK_U8)Para.Para32[1]; - if (pPrt->PFlowCtrlMode != Val8) { - /* Set New Flow Control mode */ - pPrt->PFlowCtrlMode = Val8; - - /* Restart Port */ - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_STOP, Para); - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_START, Para); - } - break; - - case SK_HWEV_SET_ROLE: - /* not possible for fiber */ - if (!pAC->GIni.GICopperType) { - break; - } - Val8 = (SK_U8)Para.Para32[1]; - if (pPrt->PMSMode != Val8) { - /* Set New Role (Master/Slave) mode */ - pPrt->PMSMode = Val8; - - /* Restart Port */ - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_STOP, Para); - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_START, Para); - } - break; - - case SK_HWEV_SET_SPEED: - if (pPrt->PhyType != SK_PHY_MARV_COPPER) { - break; - } - Val8 = (SK_U8)Para.Para32[1]; - if (pPrt->PLinkSpeed != Val8) { - /* Set New Speed parameter */ - pPrt->PLinkSpeed = Val8; - - /* Restart Port */ - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_STOP, Para); - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_START, Para); - } - break; - -#ifdef GENESIS - case SK_HWEV_HALFDUP_CHK: - if (pAC->GIni.GIGenesis) { - /* - * half duplex hangup workaround. - * See packet arbiter timeout interrupt for description - */ - pPrt->HalfDupTimerActive = SK_FALSE; - if (pPrt->PLinkModeStatus == SK_LMODE_STAT_HALF || - pPrt->PLinkModeStatus == SK_LMODE_STAT_AUTOHALF) { - /* Snap statistic counters */ - (void)SkXmUpdateStats(pAC, IoC, Port); - - (void)SkXmMacStatistic(pAC, IoC, Port, XM_TXO_OK_HI, &Val32); - - Octets = (SK_U64)Val32 << 32; - - (void)SkXmMacStatistic(pAC, IoC, Port, XM_TXO_OK_LO, &Val32); - - Octets += Val32; - - if (pPrt->LastOctets == Octets) { - /* Tx hanging, a FIFO flush restarts it */ - SkMacFlushTxFifo(pAC, IoC, Port); - } - } - } - break; -#endif /* GENESIS */ - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_SIRQ_E001, SKERR_SIRQ_E001MSG); - break; - } - - return(0); -} /* SkGeSirqEvent */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkPhyIsrBcom() - PHY interrupt service routine - * - * Description: handles all interrupts from BCom PHY - * - * Returns: N/A - */ -static void SkPhyIsrBcom( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* Io Context */ -int Port, /* Port Num = PHY Num */ -SK_U16 IStatus) /* Interrupt Status */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - SK_EVPARA Para; - - pPrt = &pAC->GIni.GP[Port]; - - if ((IStatus & PHY_B_IS_PSE) != 0) { - /* Incorrectable pair swap error */ - SK_ERR_LOG(pAC, SK_ERRCL_HW | SK_ERRCL_INIT, SKERR_SIRQ_E022, - SKERR_SIRQ_E022MSG); - } - - if ((IStatus & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE)) != 0) { - - SkHWLinkDown(pAC, IoC, Port); - - Para.Para32[0] = (SK_U32)Port; - /* Signal to RLMT */ - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - - /* Start workaround Errata #2 timer */ - SkTimerStart(pAC, IoC, &pPrt->PWaTimer, SK_WA_INA_TIME, - SKGE_HWAC, SK_HWEV_WATIM, Para); - } - -} /* SkPhyIsrBcom */ -#endif /* GENESIS */ - - -#ifdef YUKON -/****************************************************************************** - * - * SkPhyIsrGmac() - PHY interrupt service routine - * - * Description: handles all interrupts from Marvell PHY - * - * Returns: N/A - */ -static void SkPhyIsrGmac( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* Io Context */ -int Port, /* Port Num = PHY Num */ -SK_U16 IStatus) /* Interrupt Status */ -{ - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - SK_EVPARA Para; - SK_U16 Word; - - pPrt = &pAC->GIni.GP[Port]; - - if ((IStatus & (PHY_M_IS_AN_PR | PHY_M_IS_LST_CHANGE)) != 0) { - - SkHWLinkDown(pAC, IoC, Port); - - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_AUNE_ADV, &Word); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNeg.Adv: 0x%04X\n", Word)); - - /* Set Auto-negotiation advertisement */ - if (pPrt->PFlowCtrlMode == SK_FLOW_MODE_SYM_OR_REM) { - /* restore Asymmetric Pause bit */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_AUNE_ADV, - (SK_U16)(Word | PHY_M_AN_ASP)); - } - - Para.Para32[0] = (SK_U32)Port; - /* Signal to RLMT */ - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - - if ((IStatus & PHY_M_IS_AN_ERROR) != 0) { - /* Auto-Negotiation Error */ - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E023, SKERR_SIRQ_E023MSG); - } - - if ((IStatus & PHY_M_IS_FIFO_ERROR) != 0) { - /* FIFO Overflow/Underrun Error */ - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E024, SKERR_SIRQ_E024MSG); - } - -} /* SkPhyIsrGmac */ -#endif /* YUKON */ - - -#ifdef OTHER_PHY -/****************************************************************************** - * - * SkPhyIsrLone() - PHY interrupt service routine - * - * Description: handles all interrupts from LONE PHY - * - * Returns: N/A - */ -static void SkPhyIsrLone( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* Io Context */ -int Port, /* Port Num = PHY Num */ -SK_U16 IStatus) /* Interrupt Status */ -{ - SK_EVPARA Para; - - if (IStatus & (PHY_L_IS_DUP | PHY_L_IS_ISOL)) { - - SkHWLinkDown(pAC, IoC, Port); - - Para.Para32[0] = (SK_U32)Port; - /* Signal to RLMT */ - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - } - -} /* SkPhyIsrLone */ -#endif /* OTHER_PHY */ - -/* End of File */ diff --git a/drivers/net/sk98lin/ski2c.c b/drivers/net/sk98lin/ski2c.c deleted file mode 100644 index 79bf57cb5326..000000000000 --- a/drivers/net/sk98lin/ski2c.c +++ /dev/null @@ -1,1296 +0,0 @@ -/****************************************************************************** - * - * Name: ski2c.c - * Project: Gigabit Ethernet Adapters, TWSI-Module - * Version: $Revision: 1.59 $ - * Date: $Date: 2003/10/20 09:07:25 $ - * Purpose: Functions to access Voltage and Temperature Sensor - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - * I2C Protocol - */ -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: ski2c.c,v 1.59 2003/10/20 09:07:25 rschmidt Exp $ (C) Marvell. "; -#endif - -#include "h/skdrv1st.h" /* Driver Specific Definitions */ -#include "h/lm80.h" -#include "h/skdrv2nd.h" /* Adapter Control- and Driver specific Def. */ - -#ifdef __C2MAN__ -/* - I2C protocol implementation. - - General Description: - - The I2C protocol is used for the temperature sensors and for - the serial EEPROM which hold the configuration. - - This file covers functions that allow to read write and do - some bulk requests a specified I2C address. - - The Genesis has 2 I2C buses. One for the EEPROM which holds - the VPD Data and one for temperature and voltage sensor. - The following picture shows the I2C buses, I2C devices and - their control registers. - - Note: The VPD functions are in skvpd.c -. -. PCI Config I2C Bus for VPD Data: -. -. +------------+ -. | VPD EEPROM | -. +------------+ -. | -. | <-- I2C -. | -. +-----------+-----------+ -. | | -. +-----------------+ +-----------------+ -. | PCI_VPD_ADR_REG | | PCI_VPD_DAT_REG | -. +-----------------+ +-----------------+ -. -. -. I2C Bus for LM80 sensor: -. -. +-----------------+ -. | Temperature and | -. | Voltage Sensor | -. | LM80 | -. +-----------------+ -. | -. | -. I2C --> | -. | -. +----+ -. +-------------->| OR |<--+ -. | +----+ | -. +------+------+ | -. | | | -. +--------+ +--------+ +----------+ -. | B2_I2C | | B2_I2C | | B2_I2C | -. | _CTRL | | _DATA | | _SW | -. +--------+ +--------+ +----------+ -. - The I2C bus may be driven by the B2_I2C_SW or by the B2_I2C_CTRL - and B2_I2C_DATA registers. - For driver software it is recommended to use the I2C control and - data register, because I2C bus timing is done by the ASIC and - an interrupt may be received when the I2C request is completed. - - Clock Rate Timing: MIN MAX generated by - VPD EEPROM: 50 kHz 100 kHz HW - LM80 over I2C Ctrl/Data reg. 50 kHz 100 kHz HW - LM80 over B2_I2C_SW register 0 400 kHz SW - - Note: The clock generated by the hardware is dependend on the - PCI clock. If the PCI bus clock is 33 MHz, the I2C/VPD - clock is 50 kHz. - */ -intro() -{} -#endif - -#ifdef SK_DIAG -/* - * I2C Fast Mode timing values used by the LM80. - * If new devices are added to the I2C bus the timing values have to be checked. - */ -#ifndef I2C_SLOW_TIMING -#define T_CLK_LOW 1300L /* clock low time in ns */ -#define T_CLK_HIGH 600L /* clock high time in ns */ -#define T_DATA_IN_SETUP 100L /* data in Set-up Time */ -#define T_START_HOLD 600L /* start condition hold time */ -#define T_START_SETUP 600L /* start condition Set-up time */ -#define T_STOP_SETUP 600L /* stop condition Set-up time */ -#define T_BUS_IDLE 1300L /* time the bus must free after Tx */ -#define T_CLK_2_DATA_OUT 900L /* max. clock low to data output valid */ -#else /* I2C_SLOW_TIMING */ -/* I2C Standard Mode Timing */ -#define T_CLK_LOW 4700L /* clock low time in ns */ -#define T_CLK_HIGH 4000L /* clock high time in ns */ -#define T_DATA_IN_SETUP 250L /* data in Set-up Time */ -#define T_START_HOLD 4000L /* start condition hold time */ -#define T_START_SETUP 4700L /* start condition Set-up time */ -#define T_STOP_SETUP 4000L /* stop condition Set-up time */ -#define T_BUS_IDLE 4700L /* time the bus must free after Tx */ -#endif /* !I2C_SLOW_TIMING */ - -#define NS2BCLK(x) (((x)*125)/10000) - -/* - * I2C Wire Operations - * - * About I2C_CLK_LOW(): - * - * The Data Direction bit (I2C_DATA_DIR) has to be set to input when setting - * clock to low, to prevent the ASIC and the I2C data client from driving the - * serial data line simultaneously (ASIC: last bit of a byte = '1', I2C client - * send an 'ACK'). See also Concentrator Bugreport No. 10192. - */ -#define I2C_DATA_HIGH(IoC) SK_I2C_SET_BIT(IoC, I2C_DATA) -#define I2C_DATA_LOW(IoC) SK_I2C_CLR_BIT(IoC, I2C_DATA) -#define I2C_DATA_OUT(IoC) SK_I2C_SET_BIT(IoC, I2C_DATA_DIR) -#define I2C_DATA_IN(IoC) SK_I2C_CLR_BIT(IoC, I2C_DATA_DIR | I2C_DATA) -#define I2C_CLK_HIGH(IoC) SK_I2C_SET_BIT(IoC, I2C_CLK) -#define I2C_CLK_LOW(IoC) SK_I2C_CLR_BIT(IoC, I2C_CLK | I2C_DATA_DIR) -#define I2C_START_COND(IoC) SK_I2C_CLR_BIT(IoC, I2C_CLK) - -#define NS2CLKT(x) ((x*125L)/10000) - -/*--------------- I2C Interface Register Functions --------------- */ - -/* - * sending one bit - */ -void SkI2cSndBit( -SK_IOC IoC, /* I/O Context */ -SK_U8 Bit) /* Bit to send */ -{ - I2C_DATA_OUT(IoC); - if (Bit) { - I2C_DATA_HIGH(IoC); - } - else { - I2C_DATA_LOW(IoC); - } - SkDgWaitTime(IoC, NS2BCLK(T_DATA_IN_SETUP)); - I2C_CLK_HIGH(IoC); - SkDgWaitTime(IoC, NS2BCLK(T_CLK_HIGH)); - I2C_CLK_LOW(IoC); -} /* SkI2cSndBit*/ - - -/* - * Signal a start to the I2C Bus. - * - * A start is signaled when data goes to low in a high clock cycle. - * - * Ends with Clock Low. - * - * Status: not tested - */ -void SkI2cStart( -SK_IOC IoC) /* I/O Context */ -{ - /* Init data and Clock to output lines */ - /* Set Data high */ - I2C_DATA_OUT(IoC); - I2C_DATA_HIGH(IoC); - /* Set Clock high */ - I2C_CLK_HIGH(IoC); - - SkDgWaitTime(IoC, NS2BCLK(T_START_SETUP)); - - /* Set Data Low */ - I2C_DATA_LOW(IoC); - - SkDgWaitTime(IoC, NS2BCLK(T_START_HOLD)); - - /* Clock low without Data to Input */ - I2C_START_COND(IoC); - - SkDgWaitTime(IoC, NS2BCLK(T_CLK_LOW)); -} /* SkI2cStart */ - - -void SkI2cStop( -SK_IOC IoC) /* I/O Context */ -{ - /* Init data and Clock to output lines */ - /* Set Data low */ - I2C_DATA_OUT(IoC); - I2C_DATA_LOW(IoC); - - SkDgWaitTime(IoC, NS2BCLK(T_CLK_2_DATA_OUT)); - - /* Set Clock high */ - I2C_CLK_HIGH(IoC); - - SkDgWaitTime(IoC, NS2BCLK(T_STOP_SETUP)); - - /* - * Set Data High: Do it by setting the Data Line to Input. - * Because of a pull up resistor the Data Line - * floods to high. - */ - I2C_DATA_IN(IoC); - - /* - * When I2C activity is stopped - * o DATA should be set to input and - * o CLOCK should be set to high! - */ - SkDgWaitTime(IoC, NS2BCLK(T_BUS_IDLE)); -} /* SkI2cStop */ - - -/* - * Receive just one bit via the I2C bus. - * - * Note: Clock must be set to LOW before calling this function. - * - * Returns The received bit. - */ -int SkI2cRcvBit( -SK_IOC IoC) /* I/O Context */ -{ - int Bit; - SK_U8 I2cSwCtrl; - - /* Init data as input line */ - I2C_DATA_IN(IoC); - - SkDgWaitTime(IoC, NS2BCLK(T_CLK_2_DATA_OUT)); - - I2C_CLK_HIGH(IoC); - - SkDgWaitTime(IoC, NS2BCLK(T_CLK_HIGH)); - - SK_I2C_GET_SW(IoC, &I2cSwCtrl); - - Bit = (I2cSwCtrl & I2C_DATA) ? 1 : 0; - - I2C_CLK_LOW(IoC); - SkDgWaitTime(IoC, NS2BCLK(T_CLK_LOW-T_CLK_2_DATA_OUT)); - - return(Bit); -} /* SkI2cRcvBit */ - - -/* - * Receive an ACK. - * - * returns 0 If acknowledged - * 1 in case of an error - */ -int SkI2cRcvAck( -SK_IOC IoC) /* I/O Context */ -{ - /* - * Received bit must be zero. - */ - return(SkI2cRcvBit(IoC) != 0); -} /* SkI2cRcvAck */ - - -/* - * Send an NACK. - */ -void SkI2cSndNAck( -SK_IOC IoC) /* I/O Context */ -{ - /* - * Received bit must be zero. - */ - SkI2cSndBit(IoC, 1); -} /* SkI2cSndNAck */ - - -/* - * Send an ACK. - */ -void SkI2cSndAck( -SK_IOC IoC) /* I/O Context */ -{ - /* - * Received bit must be zero. - */ - SkI2cSndBit(IoC, 0); -} /* SkI2cSndAck */ - - -/* - * Send one byte to the I2C device and wait for ACK. - * - * Return acknowleged status. - */ -int SkI2cSndByte( -SK_IOC IoC, /* I/O Context */ -int Byte) /* byte to send */ -{ - int i; - - for (i = 0; i < 8; i++) { - if (Byte & (1<<(7-i))) { - SkI2cSndBit(IoC, 1); - } - else { - SkI2cSndBit(IoC, 0); - } - } - - return(SkI2cRcvAck(IoC)); -} /* SkI2cSndByte */ - - -/* - * Receive one byte and ack it. - * - * Return byte. - */ -int SkI2cRcvByte( -SK_IOC IoC, /* I/O Context */ -int Last) /* Last Byte Flag */ -{ - int i; - int Byte = 0; - - for (i = 0; i < 8; i++) { - Byte <<= 1; - Byte |= SkI2cRcvBit(IoC); - } - - if (Last) { - SkI2cSndNAck(IoC); - } - else { - SkI2cSndAck(IoC); - } - - return(Byte); -} /* SkI2cRcvByte */ - - -/* - * Start dialog and send device address - * - * Return 0 if acknowleged, 1 in case of an error - */ -int SkI2cSndDev( -SK_IOC IoC, /* I/O Context */ -int Addr, /* Device Address */ -int Rw) /* Read / Write Flag */ -{ - SkI2cStart(IoC); - Rw = ~Rw; - Rw &= I2C_WRITE; - return(SkI2cSndByte(IoC, (Addr<<1) | Rw)); -} /* SkI2cSndDev */ - -#endif /* SK_DIAG */ - -/*----------------- I2C CTRL Register Functions ----------*/ - -/* - * waits for a completion of an I2C transfer - * - * returns 0: success, transfer completes - * 1: error, transfer does not complete, I2C transfer - * killed, wait loop terminated. - */ -static int SkI2cWait( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int Event) /* complete event to wait for (I2C_READ or I2C_WRITE) */ -{ - SK_U64 StartTime; - SK_U64 CurrentTime; - SK_U32 I2cCtrl; - - StartTime = SkOsGetTime(pAC); - - do { - CurrentTime = SkOsGetTime(pAC); - - if (CurrentTime - StartTime > SK_TICKS_PER_SEC / 8) { - - SK_I2C_STOP(IoC); -#ifndef SK_DIAG - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_I2C_E002, SKERR_I2C_E002MSG); -#endif /* !SK_DIAG */ - return(1); - } - - SK_I2C_GET_CTL(IoC, &I2cCtrl); - -#ifdef xYUKON_DBG - printf("StartTime=%lu, CurrentTime=%lu\n", - StartTime, CurrentTime); - if (kbhit()) { - return(1); - } -#endif /* YUKON_DBG */ - - } while ((I2cCtrl & I2C_FLAG) == (SK_U32)Event << 31); - - return(0); -} /* SkI2cWait */ - - -/* - * waits for a completion of an I2C transfer - * - * Returns - * Nothing - */ -void SkI2cWaitIrq( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC) /* I/O Context */ -{ - SK_SENSOR *pSen; - SK_U64 StartTime; - SK_U32 IrqSrc; - - pSen = &pAC->I2c.SenTable[pAC->I2c.CurrSens]; - - if (pSen->SenState == SK_SEN_IDLE) { - return; - } - - StartTime = SkOsGetTime(pAC); - - do { - if (SkOsGetTime(pAC) - StartTime > SK_TICKS_PER_SEC / 8) { - - SK_I2C_STOP(IoC); -#ifndef SK_DIAG - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_I2C_E016, SKERR_I2C_E016MSG); -#endif /* !SK_DIAG */ - return; - } - - SK_IN32(IoC, B0_ISRC, &IrqSrc); - - } while ((IrqSrc & IS_I2C_READY) == 0); - - pSen->SenState = SK_SEN_IDLE; - return; -} /* SkI2cWaitIrq */ - -/* - * writes a single byte or 4 bytes into the I2C device - * - * returns 0: success - * 1: error - */ -static int SkI2cWrite( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 I2cData, /* I2C Data to write */ -int I2cDev, /* I2C Device Address */ -int I2cDevSize, /* I2C Device Size (e.g. I2C_025K_DEV or I2C_2K_DEV) */ -int I2cReg, /* I2C Device Register Address */ -int I2cBurst) /* I2C Burst Flag */ -{ - SK_OUT32(IoC, B2_I2C_DATA, I2cData); - - SK_I2C_CTL(IoC, I2C_WRITE, I2cDev, I2cDevSize, I2cReg, I2cBurst); - - return(SkI2cWait(pAC, IoC, I2C_WRITE)); -} /* SkI2cWrite*/ - - -#ifdef SK_DIAG -/* - * reads a single byte or 4 bytes from the I2C device - * - * returns the word read - */ -SK_U32 SkI2cRead( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int I2cDev, /* I2C Device Address */ -int I2cDevSize, /* I2C Device Size (e.g. I2C_025K_DEV or I2C_2K_DEV) */ -int I2cReg, /* I2C Device Register Address */ -int I2cBurst) /* I2C Burst Flag */ -{ - SK_U32 Data; - - SK_OUT32(IoC, B2_I2C_DATA, 0); - SK_I2C_CTL(IoC, I2C_READ, I2cDev, I2cDevSize, I2cReg, I2cBurst); - - if (SkI2cWait(pAC, IoC, I2C_READ) != 0) { - w_print("%s\n", SKERR_I2C_E002MSG); - } - - SK_IN32(IoC, B2_I2C_DATA, &Data); - - return(Data); -} /* SkI2cRead */ -#endif /* SK_DIAG */ - - -/* - * read a sensor's value - * - * This function reads a sensor's value from the I2C sensor chip. The sensor - * is defined by its index into the sensors database in the struct pAC points - * to. - * Returns - * 1 if the read is completed - * 0 if the read must be continued (I2C Bus still allocated) - */ -static int SkI2cReadSensor( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_SENSOR *pSen) /* Sensor to be read */ -{ - if (pSen->SenRead != NULL) { - return((*pSen->SenRead)(pAC, IoC, pSen)); - } - else { - return(0); /* no success */ - } -} /* SkI2cReadSensor */ - -/* - * Do the Init state 0 initialization - */ -static int SkI2cInit0( -SK_AC *pAC) /* Adapter Context */ -{ - int i; - - /* Begin with first sensor */ - pAC->I2c.CurrSens = 0; - - /* Begin with timeout control for state machine */ - pAC->I2c.TimerMode = SK_TIMER_WATCH_SM; - - /* Set sensor number to zero */ - pAC->I2c.MaxSens = 0; - -#ifndef SK_DIAG - /* Initialize Number of Dummy Reads */ - pAC->I2c.DummyReads = SK_MAX_SENSORS; -#endif - - for (i = 0; i < SK_MAX_SENSORS; i++) { - pAC->I2c.SenTable[i].SenDesc = "unknown"; - pAC->I2c.SenTable[i].SenType = SK_SEN_UNKNOWN; - pAC->I2c.SenTable[i].SenThreErrHigh = 0; - pAC->I2c.SenTable[i].SenThreErrLow = 0; - pAC->I2c.SenTable[i].SenThreWarnHigh = 0; - pAC->I2c.SenTable[i].SenThreWarnLow = 0; - pAC->I2c.SenTable[i].SenReg = LM80_FAN2_IN; - pAC->I2c.SenTable[i].SenInit = SK_SEN_DYN_INIT_NONE; - pAC->I2c.SenTable[i].SenValue = 0; - pAC->I2c.SenTable[i].SenErrFlag = SK_SEN_ERR_NOT_PRESENT; - pAC->I2c.SenTable[i].SenErrCts = 0; - pAC->I2c.SenTable[i].SenBegErrTS = 0; - pAC->I2c.SenTable[i].SenState = SK_SEN_IDLE; - pAC->I2c.SenTable[i].SenRead = NULL; - pAC->I2c.SenTable[i].SenDev = 0; - } - - /* Now we are "INIT data"ed */ - pAC->I2c.InitLevel = SK_INIT_DATA; - return(0); -} /* SkI2cInit0*/ - - -/* - * Do the init state 1 initialization - * - * initialize the following register of the LM80: - * Configuration register: - * - START, noINT, activeLOW, noINT#Clear, noRESET, noCI, noGPO#, noINIT - * - * Interrupt Mask Register 1: - * - all interrupts are Disabled (0xff) - * - * Interrupt Mask Register 2: - * - all interrupts are Disabled (0xff) Interrupt modi doesn't matter. - * - * Fan Divisor/RST_OUT register: - * - Divisors set to 1 (bits 00), all others 0s. - * - * OS# Configuration/Temperature resolution Register: - * - all 0s - * - */ -static int SkI2cInit1( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC) /* I/O Context */ -{ - int i; - SK_U8 I2cSwCtrl; - SK_GEPORT *pPrt; /* GIni Port struct pointer */ - - if (pAC->I2c.InitLevel != SK_INIT_DATA) { - /* ReInit not needed in I2C module */ - return(0); - } - - /* Set the Direction of I2C-Data Pin to IN */ - SK_I2C_CLR_BIT(IoC, I2C_DATA_DIR | I2C_DATA); - /* Check for 32-Bit Yukon with Low at I2C-Data Pin */ - SK_I2C_GET_SW(IoC, &I2cSwCtrl); - - if ((I2cSwCtrl & I2C_DATA) == 0) { - /* this is a 32-Bit board */ - pAC->GIni.GIYukon32Bit = SK_TRUE; - return(0); - } - - /* Check for 64 Bit Yukon without sensors */ - if (SkI2cWrite(pAC, IoC, 0, LM80_ADDR, I2C_025K_DEV, LM80_CFG, 0) != 0) { - return(0); - } - - (void)SkI2cWrite(pAC, IoC, 0xffUL, LM80_ADDR, I2C_025K_DEV, LM80_IMSK_1, 0); - - (void)SkI2cWrite(pAC, IoC, 0xffUL, LM80_ADDR, I2C_025K_DEV, LM80_IMSK_2, 0); - - (void)SkI2cWrite(pAC, IoC, 0, LM80_ADDR, I2C_025K_DEV, LM80_FAN_CTRL, 0); - - (void)SkI2cWrite(pAC, IoC, 0, LM80_ADDR, I2C_025K_DEV, LM80_TEMP_CTRL, 0); - - (void)SkI2cWrite(pAC, IoC, (SK_U32)LM80_CFG_START, LM80_ADDR, I2C_025K_DEV, - LM80_CFG, 0); - - /* - * MaxSens has to be updated here, because PhyType is not - * set when performing Init Level 0 - */ - pAC->I2c.MaxSens = 5; - - pPrt = &pAC->GIni.GP[0]; - - if (pAC->GIni.GIGenesis) { - if (pPrt->PhyType == SK_PHY_BCOM) { - if (pAC->GIni.GIMacsFound == 1) { - pAC->I2c.MaxSens += 1; - } - else { - pAC->I2c.MaxSens += 3; - } - } - } - else { - pAC->I2c.MaxSens += 3; - } - - for (i = 0; i < pAC->I2c.MaxSens; i++) { - switch (i) { - case 0: - pAC->I2c.SenTable[i].SenDesc = "Temperature"; - pAC->I2c.SenTable[i].SenType = SK_SEN_TEMP; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_TEMP_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_TEMP_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_TEMP_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_TEMP_LOW_ERR; - pAC->I2c.SenTable[i].SenReg = LM80_TEMP_IN; - break; - case 1: - pAC->I2c.SenTable[i].SenDesc = "Voltage PCI"; - pAC->I2c.SenTable[i].SenType = SK_SEN_VOLT; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_PCI_5V_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_PCI_5V_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_PCI_5V_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_PCI_5V_LOW_ERR; - pAC->I2c.SenTable[i].SenReg = LM80_VT0_IN; - break; - case 2: - pAC->I2c.SenTable[i].SenDesc = "Voltage PCI-IO"; - pAC->I2c.SenTable[i].SenType = SK_SEN_VOLT; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_PCI_IO_5V_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_PCI_IO_5V_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_PCI_IO_3V3_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_PCI_IO_3V3_LOW_ERR; - pAC->I2c.SenTable[i].SenReg = LM80_VT1_IN; - pAC->I2c.SenTable[i].SenInit = SK_SEN_DYN_INIT_PCI_IO; - break; - case 3: - pAC->I2c.SenTable[i].SenDesc = "Voltage ASIC"; - pAC->I2c.SenTable[i].SenType = SK_SEN_VOLT; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_VDD_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_VDD_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_VDD_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_VDD_LOW_ERR; - pAC->I2c.SenTable[i].SenReg = LM80_VT2_IN; - break; - case 4: - if (pAC->GIni.GIGenesis) { - if (pPrt->PhyType == SK_PHY_BCOM) { - pAC->I2c.SenTable[i].SenDesc = "Voltage PHY A PLL"; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_PLL_3V3_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_PLL_3V3_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_PLL_3V3_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_PLL_3V3_LOW_ERR; - } - else { - pAC->I2c.SenTable[i].SenDesc = "Voltage PMA"; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_PLL_3V3_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_PLL_3V3_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_PLL_3V3_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_PLL_3V3_LOW_ERR; - } - } - else { - pAC->I2c.SenTable[i].SenDesc = "Voltage VAUX"; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_VAUX_3V3_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_VAUX_3V3_HIGH_WARN; - if (pAC->GIni.GIVauxAvail) { - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_VAUX_3V3_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_VAUX_3V3_LOW_ERR; - } - else { - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_VAUX_0V_WARN_ERR; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_VAUX_0V_WARN_ERR; - } - } - pAC->I2c.SenTable[i].SenType = SK_SEN_VOLT; - pAC->I2c.SenTable[i].SenReg = LM80_VT3_IN; - break; - case 5: - if (pAC->GIni.GIGenesis) { - pAC->I2c.SenTable[i].SenDesc = "Voltage PHY 2V5"; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_PHY_2V5_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_PHY_2V5_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_PHY_2V5_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_PHY_2V5_LOW_ERR; - } - else { - pAC->I2c.SenTable[i].SenDesc = "Voltage Core 1V5"; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_CORE_1V5_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_CORE_1V5_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_CORE_1V5_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_CORE_1V5_LOW_ERR; - } - pAC->I2c.SenTable[i].SenType = SK_SEN_VOLT; - pAC->I2c.SenTable[i].SenReg = LM80_VT4_IN; - break; - case 6: - if (pAC->GIni.GIGenesis) { - pAC->I2c.SenTable[i].SenDesc = "Voltage PHY B PLL"; - } - else { - pAC->I2c.SenTable[i].SenDesc = "Voltage PHY 3V3"; - } - pAC->I2c.SenTable[i].SenType = SK_SEN_VOLT; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_PLL_3V3_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_PLL_3V3_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_PLL_3V3_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_PLL_3V3_LOW_ERR; - pAC->I2c.SenTable[i].SenReg = LM80_VT5_IN; - break; - case 7: - if (pAC->GIni.GIGenesis) { - pAC->I2c.SenTable[i].SenDesc = "Speed Fan"; - pAC->I2c.SenTable[i].SenType = SK_SEN_FAN; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_FAN_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_FAN_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_FAN_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_FAN_LOW_ERR; - pAC->I2c.SenTable[i].SenReg = LM80_FAN2_IN; - } - else { - pAC->I2c.SenTable[i].SenDesc = "Voltage PHY 2V5"; - pAC->I2c.SenTable[i].SenType = SK_SEN_VOLT; - pAC->I2c.SenTable[i].SenThreErrHigh = SK_SEN_PHY_2V5_HIGH_ERR; - pAC->I2c.SenTable[i].SenThreWarnHigh = SK_SEN_PHY_2V5_HIGH_WARN; - pAC->I2c.SenTable[i].SenThreWarnLow = SK_SEN_PHY_2V5_LOW_WARN; - pAC->I2c.SenTable[i].SenThreErrLow = SK_SEN_PHY_2V5_LOW_ERR; - pAC->I2c.SenTable[i].SenReg = LM80_VT6_IN; - } - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_INIT | SK_ERRCL_SW, - SKERR_I2C_E001, SKERR_I2C_E001MSG); - break; - } - - pAC->I2c.SenTable[i].SenValue = 0; - pAC->I2c.SenTable[i].SenErrFlag = SK_SEN_ERR_OK; - pAC->I2c.SenTable[i].SenErrCts = 0; - pAC->I2c.SenTable[i].SenBegErrTS = 0; - pAC->I2c.SenTable[i].SenState = SK_SEN_IDLE; - pAC->I2c.SenTable[i].SenRead = SkLm80ReadSensor; - pAC->I2c.SenTable[i].SenDev = LM80_ADDR; - } - -#ifndef SK_DIAG - pAC->I2c.DummyReads = pAC->I2c.MaxSens; -#endif /* !SK_DIAG */ - - /* Clear I2C IRQ */ - SK_OUT32(IoC, B2_I2C_IRQ, I2C_CLR_IRQ); - - /* Now we are I/O initialized */ - pAC->I2c.InitLevel = SK_INIT_IO; - return(0); -} /* SkI2cInit1 */ - - -/* - * Init level 2: Start first sensor read. - */ -static int SkI2cInit2( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC) /* I/O Context */ -{ - int ReadComplete; - SK_SENSOR *pSen; - - if (pAC->I2c.InitLevel != SK_INIT_IO) { - /* ReInit not needed in I2C module */ - /* Init0 and Init2 not permitted */ - return(0); - } - - pSen = &pAC->I2c.SenTable[pAC->I2c.CurrSens]; - ReadComplete = SkI2cReadSensor(pAC, IoC, pSen); - - if (ReadComplete) { - SK_ERR_LOG(pAC, SK_ERRCL_INIT, SKERR_I2C_E008, SKERR_I2C_E008MSG); - } - - /* Now we are correctly initialized */ - pAC->I2c.InitLevel = SK_INIT_RUN; - - return(0); -} /* SkI2cInit2*/ - - -/* - * Initialize I2C devices - * - * Get the first voltage value and discard it. - * Go into temperature read mode. A default pointer is not set. - * - * The things to be done depend on the init level in the parameter list: - * Level 0: - * Initialize only the data structures. Do NOT access hardware. - * Level 1: - * Initialize hardware through SK_IN / SK_OUT commands. Do NOT use interrupts. - * Level 2: - * Everything is possible. Interrupts may be used from now on. - * - * return: - * 0 = success - * other = error. - */ -int SkI2cInit( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context needed in levels 1 and 2 */ -int Level) /* Init Level */ -{ - - switch (Level) { - case SK_INIT_DATA: - return(SkI2cInit0(pAC)); - case SK_INIT_IO: - return(SkI2cInit1(pAC, IoC)); - case SK_INIT_RUN: - return(SkI2cInit2(pAC, IoC)); - default: - break; - } - - return(0); -} /* SkI2cInit */ - - -#ifndef SK_DIAG - -/* - * Interrupt service function for the I2C Interface - * - * Clears the Interrupt source - * - * Reads the register and check it for sending a trap. - * - * Starts the timer if necessary. - */ -void SkI2cIsr( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC) /* I/O Context */ -{ - SK_EVPARA Para; - - /* Clear I2C IRQ */ - SK_OUT32(IoC, B2_I2C_IRQ, I2C_CLR_IRQ); - - Para.Para64 = 0; - SkEventQueue(pAC, SKGE_I2C, SK_I2CEV_IRQ, Para); -} /* SkI2cIsr */ - - -/* - * Check this sensors Value against the threshold and send events. - */ -static void SkI2cCheckSensor( -SK_AC *pAC, /* Adapter Context */ -SK_SENSOR *pSen) -{ - SK_EVPARA ParaLocal; - SK_BOOL TooHigh; /* Is sensor too high? */ - SK_BOOL TooLow; /* Is sensor too low? */ - SK_U64 CurrTime; /* Current Time */ - SK_BOOL DoTrapSend; /* We need to send a trap */ - SK_BOOL DoErrLog; /* We need to log the error */ - SK_BOOL IsError; /* We need to log the error */ - - /* Check Dummy Reads first */ - if (pAC->I2c.DummyReads > 0) { - pAC->I2c.DummyReads--; - return; - } - - /* Get the current time */ - CurrTime = SkOsGetTime(pAC); - - /* Set para to the most useful setting: The current sensor. */ - ParaLocal.Para64 = (SK_U64)pAC->I2c.CurrSens; - - /* Check the Value against the thresholds. First: Error Thresholds */ - TooHigh = (pSen->SenValue > pSen->SenThreErrHigh); - TooLow = (pSen->SenValue < pSen->SenThreErrLow); - - IsError = SK_FALSE; - if (TooHigh || TooLow) { - /* Error condition is satisfied */ - DoTrapSend = SK_TRUE; - DoErrLog = SK_TRUE; - - /* Now error condition is satisfied */ - IsError = SK_TRUE; - - if (pSen->SenErrFlag == SK_SEN_ERR_ERR) { - /* This state is the former one */ - - /* So check first whether we have to send a trap */ - if (pSen->SenLastErrTrapTS + SK_SEN_ERR_TR_HOLD > - CurrTime) { - /* - * Do NOT send the Trap. The hold back time - * has to run out first. - */ - DoTrapSend = SK_FALSE; - } - - /* Check now whether we have to log an Error */ - if (pSen->SenLastErrLogTS + SK_SEN_ERR_LOG_HOLD > - CurrTime) { - /* - * Do NOT log the error. The hold back time - * has to run out first. - */ - DoErrLog = SK_FALSE; - } - } - else { - /* We came from a different state -> Set Begin Time Stamp */ - pSen->SenBegErrTS = CurrTime; - pSen->SenErrFlag = SK_SEN_ERR_ERR; - } - - if (DoTrapSend) { - /* Set current Time */ - pSen->SenLastErrTrapTS = CurrTime; - pSen->SenErrCts++; - - /* Queue PNMI Event */ - SkEventQueue(pAC, SKGE_PNMI, (TooHigh ? - SK_PNMI_EVT_SEN_ERR_UPP : - SK_PNMI_EVT_SEN_ERR_LOW), - ParaLocal); - } - - if (DoErrLog) { - /* Set current Time */ - pSen->SenLastErrLogTS = CurrTime; - - if (pSen->SenType == SK_SEN_TEMP) { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_I2C_E011, SKERR_I2C_E011MSG); - } - else if (pSen->SenType == SK_SEN_VOLT) { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_I2C_E012, SKERR_I2C_E012MSG); - } - else { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_I2C_E015, SKERR_I2C_E015MSG); - } - } - } - - /* Check the Value against the thresholds */ - /* 2nd: Warning thresholds */ - TooHigh = (pSen->SenValue > pSen->SenThreWarnHigh); - TooLow = (pSen->SenValue < pSen->SenThreWarnLow); - - if (!IsError && (TooHigh || TooLow)) { - /* Error condition is satisfied */ - DoTrapSend = SK_TRUE; - DoErrLog = SK_TRUE; - - if (pSen->SenErrFlag == SK_SEN_ERR_WARN) { - /* This state is the former one */ - - /* So check first whether we have to send a trap */ - if (pSen->SenLastWarnTrapTS + SK_SEN_WARN_TR_HOLD > CurrTime) { - /* - * Do NOT send the Trap. The hold back time - * has to run out first. - */ - DoTrapSend = SK_FALSE; - } - - /* Check now whether we have to log an Error */ - if (pSen->SenLastWarnLogTS + SK_SEN_WARN_LOG_HOLD > CurrTime) { - /* - * Do NOT log the error. The hold back time - * has to run out first. - */ - DoErrLog = SK_FALSE; - } - } - else { - /* We came from a different state -> Set Begin Time Stamp */ - pSen->SenBegWarnTS = CurrTime; - pSen->SenErrFlag = SK_SEN_ERR_WARN; - } - - if (DoTrapSend) { - /* Set current Time */ - pSen->SenLastWarnTrapTS = CurrTime; - pSen->SenWarnCts++; - - /* Queue PNMI Event */ - SkEventQueue(pAC, SKGE_PNMI, (TooHigh ? - SK_PNMI_EVT_SEN_WAR_UPP : - SK_PNMI_EVT_SEN_WAR_LOW), - ParaLocal); - } - - if (DoErrLog) { - /* Set current Time */ - pSen->SenLastWarnLogTS = CurrTime; - - if (pSen->SenType == SK_SEN_TEMP) { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_I2C_E009, SKERR_I2C_E009MSG); - } - else if (pSen->SenType == SK_SEN_VOLT) { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_I2C_E010, SKERR_I2C_E010MSG); - } - else { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_I2C_E014, SKERR_I2C_E014MSG); - } - } - } - - /* Check for NO error at all */ - if (!IsError && !TooHigh && !TooLow) { - /* Set o.k. Status if no error and no warning condition */ - pSen->SenErrFlag = SK_SEN_ERR_OK; - } - - /* End of check against the thresholds */ - - /* Bug fix AF: 16.Aug.2001: Correct the init base - * of LM80 sensor. - */ - if (pSen->SenInit == SK_SEN_DYN_INIT_PCI_IO) { - - pSen->SenInit = SK_SEN_DYN_INIT_NONE; - - if (pSen->SenValue > SK_SEN_PCI_IO_RANGE_LIMITER) { - /* 5V PCI-IO Voltage */ - pSen->SenThreWarnLow = SK_SEN_PCI_IO_5V_LOW_WARN; - pSen->SenThreErrLow = SK_SEN_PCI_IO_5V_LOW_ERR; - } - else { - /* 3.3V PCI-IO Voltage */ - pSen->SenThreWarnHigh = SK_SEN_PCI_IO_3V3_HIGH_WARN; - pSen->SenThreErrHigh = SK_SEN_PCI_IO_3V3_HIGH_ERR; - } - } - -#ifdef TEST_ONLY - /* Dynamic thresholds also for VAUX of LM80 sensor */ - if (pSen->SenInit == SK_SEN_DYN_INIT_VAUX) { - - pSen->SenInit = SK_SEN_DYN_INIT_NONE; - - /* 3.3V VAUX Voltage */ - if (pSen->SenValue > SK_SEN_VAUX_RANGE_LIMITER) { - pSen->SenThreWarnLow = SK_SEN_VAUX_3V3_LOW_WARN; - pSen->SenThreErrLow = SK_SEN_VAUX_3V3_LOW_ERR; - } - /* 0V VAUX Voltage */ - else { - pSen->SenThreWarnHigh = SK_SEN_VAUX_0V_WARN_ERR; - pSen->SenThreErrHigh = SK_SEN_VAUX_0V_WARN_ERR; - } - } - - /* - * Check initialization state: - * The VIO Thresholds need adaption - */ - if (!pSen->SenInit && pSen->SenReg == LM80_VT1_IN && - pSen->SenValue > SK_SEN_WARNLOW2C && - pSen->SenValue < SK_SEN_WARNHIGH2) { - pSen->SenThreErrLow = SK_SEN_ERRLOW2C; - pSen->SenThreWarnLow = SK_SEN_WARNLOW2C; - pSen->SenInit = SK_TRUE; - } - - if (!pSen->SenInit && pSen->SenReg == LM80_VT1_IN && - pSen->SenValue > SK_SEN_WARNLOW2 && - pSen->SenValue < SK_SEN_WARNHIGH2C) { - pSen->SenThreErrHigh = SK_SEN_ERRHIGH2C; - pSen->SenThreWarnHigh = SK_SEN_WARNHIGH2C; - pSen->SenInit = SK_TRUE; - } -#endif - - if (pSen->SenInit != SK_SEN_DYN_INIT_NONE) { - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_I2C_E013, SKERR_I2C_E013MSG); - } -} /* SkI2cCheckSensor */ - - -/* - * The only Event to be served is the timeout event - * - */ -int SkI2cEvent( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 Event, /* Module specific Event */ -SK_EVPARA Para) /* Event specific Parameter */ -{ - int ReadComplete; - SK_SENSOR *pSen; - SK_U32 Time; - SK_EVPARA ParaLocal; - int i; - - /* New case: no sensors */ - if (pAC->I2c.MaxSens == 0) { - return(0); - } - - switch (Event) { - case SK_I2CEV_IRQ: - pSen = &pAC->I2c.SenTable[pAC->I2c.CurrSens]; - ReadComplete = SkI2cReadSensor(pAC, IoC, pSen); - - if (ReadComplete) { - /* Check sensor against defined thresholds */ - SkI2cCheckSensor(pAC, pSen); - - /* Increment Current sensor and set appropriate Timeout */ - pAC->I2c.CurrSens++; - if (pAC->I2c.CurrSens >= pAC->I2c.MaxSens) { - pAC->I2c.CurrSens = 0; - Time = SK_I2C_TIM_LONG; - } - else { - Time = SK_I2C_TIM_SHORT; - } - - /* Start Timer */ - ParaLocal.Para64 = (SK_U64)0; - - pAC->I2c.TimerMode = SK_TIMER_NEW_GAUGING; - - SkTimerStart(pAC, IoC, &pAC->I2c.SenTimer, Time, - SKGE_I2C, SK_I2CEV_TIM, ParaLocal); - } - else { - /* Start Timer */ - ParaLocal.Para64 = (SK_U64)0; - - pAC->I2c.TimerMode = SK_TIMER_WATCH_SM; - - SkTimerStart(pAC, IoC, &pAC->I2c.SenTimer, SK_I2C_TIM_WATCH, - SKGE_I2C, SK_I2CEV_TIM, ParaLocal); - } - break; - case SK_I2CEV_TIM: - if (pAC->I2c.TimerMode == SK_TIMER_NEW_GAUGING) { - - ParaLocal.Para64 = (SK_U64)0; - SkTimerStop(pAC, IoC, &pAC->I2c.SenTimer); - - pSen = &pAC->I2c.SenTable[pAC->I2c.CurrSens]; - ReadComplete = SkI2cReadSensor(pAC, IoC, pSen); - - if (ReadComplete) { - /* Check sensor against defined thresholds */ - SkI2cCheckSensor(pAC, pSen); - - /* Increment Current sensor and set appropriate Timeout */ - pAC->I2c.CurrSens++; - if (pAC->I2c.CurrSens == pAC->I2c.MaxSens) { - pAC->I2c.CurrSens = 0; - Time = SK_I2C_TIM_LONG; - } - else { - Time = SK_I2C_TIM_SHORT; - } - - /* Start Timer */ - ParaLocal.Para64 = (SK_U64)0; - - pAC->I2c.TimerMode = SK_TIMER_NEW_GAUGING; - - SkTimerStart(pAC, IoC, &pAC->I2c.SenTimer, Time, - SKGE_I2C, SK_I2CEV_TIM, ParaLocal); - } - } - else { - pSen = &pAC->I2c.SenTable[pAC->I2c.CurrSens]; - pSen->SenErrFlag = SK_SEN_ERR_FAULTY; - SK_I2C_STOP(IoC); - - /* Increment Current sensor and set appropriate Timeout */ - pAC->I2c.CurrSens++; - if (pAC->I2c.CurrSens == pAC->I2c.MaxSens) { - pAC->I2c.CurrSens = 0; - Time = SK_I2C_TIM_LONG; - } - else { - Time = SK_I2C_TIM_SHORT; - } - - /* Start Timer */ - ParaLocal.Para64 = (SK_U64)0; - - pAC->I2c.TimerMode = SK_TIMER_NEW_GAUGING; - - SkTimerStart(pAC, IoC, &pAC->I2c.SenTimer, Time, - SKGE_I2C, SK_I2CEV_TIM, ParaLocal); - } - break; - case SK_I2CEV_CLEAR: - for (i = 0; i < SK_MAX_SENSORS; i++) { - pAC->I2c.SenTable[i].SenErrFlag = SK_SEN_ERR_OK; - pAC->I2c.SenTable[i].SenErrCts = 0; - pAC->I2c.SenTable[i].SenWarnCts = 0; - pAC->I2c.SenTable[i].SenBegErrTS = 0; - pAC->I2c.SenTable[i].SenBegWarnTS = 0; - pAC->I2c.SenTable[i].SenLastErrTrapTS = (SK_U64)0; - pAC->I2c.SenTable[i].SenLastErrLogTS = (SK_U64)0; - pAC->I2c.SenTable[i].SenLastWarnTrapTS = (SK_U64)0; - pAC->I2c.SenTable[i].SenLastWarnLogTS = (SK_U64)0; - } - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_I2C_E006, SKERR_I2C_E006MSG); - } - - return(0); -} /* SkI2cEvent*/ - -#endif /* !SK_DIAG */ diff --git a/drivers/net/sk98lin/sklm80.c b/drivers/net/sk98lin/sklm80.c deleted file mode 100644 index a204f5bb55d4..000000000000 --- a/drivers/net/sk98lin/sklm80.c +++ /dev/null @@ -1,141 +0,0 @@ -/****************************************************************************** - * - * Name: sklm80.c - * Project: Gigabit Ethernet Adapters, TWSI-Module - * Version: $Revision: 1.22 $ - * Date: $Date: 2003/10/20 09:08:21 $ - * Purpose: Functions to access Voltage and Temperature Sensor (LM80) - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - LM80 functions -*/ -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: sklm80.c,v 1.22 2003/10/20 09:08:21 rschmidt Exp $ (C) Marvell. "; -#endif - -#include "h/skdrv1st.h" /* Driver Specific Definitions */ -#include "h/lm80.h" -#include "h/skdrv2nd.h" /* Adapter Control- and Driver specific Def. */ - -#define BREAK_OR_WAIT(pAC,IoC,Event) break - -/* - * read a sensors value (LM80 specific) - * - * This function reads a sensors value from the I2C sensor chip LM80. - * The sensor is defined by its index into the sensors database in the struct - * pAC points to. - * - * Returns 1 if the read is completed - * 0 if the read must be continued (I2C Bus still allocated) - */ -int SkLm80ReadSensor( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context needed in level 1 and 2 */ -SK_SENSOR *pSen) /* Sensor to be read */ -{ - SK_I32 Value; - - switch (pSen->SenState) { - case SK_SEN_IDLE: - /* Send address to ADDR register */ - SK_I2C_CTL(IoC, I2C_READ, pSen->SenDev, I2C_025K_DEV, pSen->SenReg, 0); - - pSen->SenState = SK_SEN_VALUE ; - BREAK_OR_WAIT(pAC, IoC, I2C_READ); - - case SK_SEN_VALUE: - /* Read value from data register */ - SK_IN32(IoC, B2_I2C_DATA, ((SK_U32 *)&Value)); - - Value &= 0xff; /* only least significant byte is valid */ - - /* Do NOT check the Value against the thresholds */ - /* Checking is done in the calling instance */ - - if (pSen->SenType == SK_SEN_VOLT) { - /* Voltage sensor */ - pSen->SenValue = Value * SK_LM80_VT_LSB; - pSen->SenState = SK_SEN_IDLE ; - return(1); - } - - if (pSen->SenType == SK_SEN_FAN) { - if (Value != 0 && Value != 0xff) { - /* Fan speed counter */ - pSen->SenValue = SK_LM80_FAN_FAKTOR/Value; - } - else { - /* Indicate Fan error */ - pSen->SenValue = 0; - } - pSen->SenState = SK_SEN_IDLE ; - return(1); - } - - /* First: correct the value: it might be negative */ - if ((Value & 0x80) != 0) { - /* Value is negative */ - Value = Value - 256; - } - - /* We have a temperature sensor and need to get the signed extension. - * For now we get the extension from the last reading, so in the normal - * case we won't see flickering temperatures. - */ - pSen->SenValue = (Value * SK_LM80_TEMP_LSB) + - (pSen->SenValue % SK_LM80_TEMP_LSB); - - /* Send address to ADDR register */ - SK_I2C_CTL(IoC, I2C_READ, pSen->SenDev, I2C_025K_DEV, LM80_TEMP_CTRL, 0); - - pSen->SenState = SK_SEN_VALEXT ; - BREAK_OR_WAIT(pAC, IoC, I2C_READ); - - case SK_SEN_VALEXT: - /* Read value from data register */ - SK_IN32(IoC, B2_I2C_DATA, ((SK_U32 *)&Value)); - Value &= LM80_TEMP_LSB_9; /* only bit 7 is valid */ - - /* cut the LSB bit */ - pSen->SenValue = ((pSen->SenValue / SK_LM80_TEMP_LSB) * - SK_LM80_TEMP_LSB); - - if (pSen->SenValue < 0) { - /* Value negative: The bit value must be subtracted */ - pSen->SenValue -= ((Value >> 7) * SK_LM80_TEMPEXT_LSB); - } - else { - /* Value positive: The bit value must be added */ - pSen->SenValue += ((Value >> 7) * SK_LM80_TEMPEXT_LSB); - } - - pSen->SenState = SK_SEN_IDLE ; - return(1); - - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_I2C_E007, SKERR_I2C_E007MSG); - return(1); - } - - /* Not completed */ - return(0); -} - diff --git a/drivers/net/sk98lin/skqueue.c b/drivers/net/sk98lin/skqueue.c deleted file mode 100644 index 0275b4f71d9b..000000000000 --- a/drivers/net/sk98lin/skqueue.c +++ /dev/null @@ -1,179 +0,0 @@ -/****************************************************************************** - * - * Name: skqueue.c - * Project: Gigabit Ethernet Adapters, Event Scheduler Module - * Version: $Revision: 1.20 $ - * Date: $Date: 2003/09/16 13:44:00 $ - * Purpose: Management of an event queue. - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - - -/* - * Event queue and dispatcher - */ -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: skqueue.c,v 1.20 2003/09/16 13:44:00 rschmidt Exp $ (C) Marvell."; -#endif - -#include "h/skdrv1st.h" /* Driver Specific Definitions */ -#include "h/skqueue.h" /* Queue Definitions */ -#include "h/skdrv2nd.h" /* Adapter Control- and Driver specific Def. */ - -#ifdef __C2MAN__ -/* - Event queue management. - - General Description: - - */ -intro() -{} -#endif - -#define PRINTF(a,b,c) - -/* - * init event queue management - * - * Must be called during init level 0. - */ -void SkEventInit( -SK_AC *pAC, /* Adapter context */ -SK_IOC Ioc, /* IO context */ -int Level) /* Init level */ -{ - switch (Level) { - case SK_INIT_DATA: - pAC->Event.EvPut = pAC->Event.EvGet = pAC->Event.EvQueue; - break; - default: - break; - } -} - -/* - * add event to queue - */ -void SkEventQueue( -SK_AC *pAC, /* Adapters context */ -SK_U32 Class, /* Event Class */ -SK_U32 Event, /* Event to be queued */ -SK_EVPARA Para) /* Event parameter */ -{ - pAC->Event.EvPut->Class = Class; - pAC->Event.EvPut->Event = Event; - pAC->Event.EvPut->Para = Para; - - if (++pAC->Event.EvPut == &pAC->Event.EvQueue[SK_MAX_EVENT]) - pAC->Event.EvPut = pAC->Event.EvQueue; - - if (pAC->Event.EvPut == pAC->Event.EvGet) { - SK_ERR_LOG(pAC, SK_ERRCL_NORES, SKERR_Q_E001, SKERR_Q_E001MSG); - } -} - -/* - * event dispatcher - * while event queue is not empty - * get event from queue - * send command to state machine - * end - * return error reported by individual Event function - * 0 if no error occured. - */ -int SkEventDispatcher( -SK_AC *pAC, /* Adapters Context */ -SK_IOC Ioc) /* Io context */ -{ - SK_EVENTELEM *pEv; /* pointer into queue */ - SK_U32 Class; - int Rtv; - - pEv = pAC->Event.EvGet; - - PRINTF("dispatch get %x put %x\n", pEv, pAC->Event.ev_put); - - while (pEv != pAC->Event.EvPut) { - PRINTF("dispatch Class %d Event %d\n", pEv->Class, pEv->Event); - - switch (Class = pEv->Class) { -#ifndef SK_USE_LAC_EV -#ifndef SK_SLIM - case SKGE_RLMT: /* RLMT Event */ - Rtv = SkRlmtEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; - case SKGE_I2C: /* I2C Event */ - Rtv = SkI2cEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; - case SKGE_PNMI: /* PNMI Event */ - Rtv = SkPnmiEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; -#endif /* not SK_SLIM */ -#endif /* not SK_USE_LAC_EV */ - case SKGE_DRV: /* Driver Event */ - Rtv = SkDrvEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; -#ifndef SK_USE_SW_TIMER - case SKGE_HWAC: - Rtv = SkGeSirqEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; -#else /* !SK_USE_SW_TIMER */ - case SKGE_SWT : - Rtv = SkSwtEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; -#endif /* !SK_USE_SW_TIMER */ -#ifdef SK_USE_LAC_EV - case SKGE_LACP : - Rtv = SkLacpEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; - case SKGE_RSF : - Rtv = SkRsfEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; - case SKGE_MARKER : - Rtv = SkMarkerEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; - case SKGE_FD : - Rtv = SkFdEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; -#endif /* SK_USE_LAC_EV */ -#ifdef SK_USE_CSUM - case SKGE_CSUM : - Rtv = SkCsEvent(pAC, Ioc, pEv->Event, pEv->Para); - break; -#endif /* SK_USE_CSUM */ - default : - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_Q_E002, SKERR_Q_E002MSG); - Rtv = 0; - } - - if (Rtv != 0) { - return(Rtv); - } - - if (++pEv == &pAC->Event.EvQueue[SK_MAX_EVENT]) - pEv = pAC->Event.EvQueue; - - /* Renew get: it is used in queue_events to detect overruns */ - pAC->Event.EvGet = pEv; - } - - return(0); -} - -/* End of file */ diff --git a/drivers/net/sk98lin/skrlmt.c b/drivers/net/sk98lin/skrlmt.c deleted file mode 100644 index be8d1ccddf6d..000000000000 --- a/drivers/net/sk98lin/skrlmt.c +++ /dev/null @@ -1,3257 +0,0 @@ -/****************************************************************************** - * - * Name: skrlmt.c - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.69 $ - * Date: $Date: 2003/04/15 09:39:22 $ - * Purpose: Manage links on SK-NET Adapters, esp. redundant ones. - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/****************************************************************************** - * - * Description: - * - * This module contains code for Link ManagemenT (LMT) of SK-NET Adapters. - * It is mainly intended for adapters with more than one link. - * For such adapters, this module realizes Redundant Link ManagemenT (RLMT). - * - * Include File Hierarchy: - * - * "skdrv1st.h" - * "skdrv2nd.h" - * - ******************************************************************************/ - -#ifndef lint -static const char SysKonnectFileId[] = - "@(#) $Id: skrlmt.c,v 1.69 2003/04/15 09:39:22 tschilli Exp $ (C) Marvell."; -#endif /* !defined(lint) */ - -#define __SKRLMT_C - -#ifdef __cplusplus -extern "C" { -#endif /* cplusplus */ - -#include "h/skdrv1st.h" -#include "h/skdrv2nd.h" - -/* defines ********************************************************************/ - -#ifndef SK_HWAC_LINK_LED -#define SK_HWAC_LINK_LED(a,b,c,d) -#endif /* !defined(SK_HWAC_LINK_LED) */ - -#ifndef DEBUG -#define RLMT_STATIC static -#else /* DEBUG */ -#define RLMT_STATIC - -#ifndef SK_LITTLE_ENDIAN -/* First 32 bits */ -#define OFFS_LO32 1 - -/* Second 32 bits */ -#define OFFS_HI32 0 -#else /* SK_LITTLE_ENDIAN */ -/* First 32 bits */ -#define OFFS_LO32 0 - -/* Second 32 bits */ -#define OFFS_HI32 1 -#endif /* SK_LITTLE_ENDIAN */ - -#endif /* DEBUG */ - -/* ----- Private timeout values ----- */ - -#define SK_RLMT_MIN_TO_VAL 125000 /* 1/8 sec. */ -#define SK_RLMT_DEF_TO_VAL 1000000 /* 1 sec. */ -#define SK_RLMT_PORTDOWN_TIM_VAL 900000 /* another 0.9 sec. */ -#define SK_RLMT_PORTSTART_TIM_VAL 100000 /* 0.1 sec. */ -#define SK_RLMT_PORTUP_TIM_VAL 2500000 /* 2.5 sec. */ -#define SK_RLMT_SEG_TO_VAL 900000000 /* 15 min. */ - -/* Assume tick counter increment is 1 - may be set OS-dependent. */ -#ifndef SK_TICK_INCR -#define SK_TICK_INCR SK_CONSTU64(1) -#endif /* !defined(SK_TICK_INCR) */ - -/* - * Amount that a time stamp must be later to be recognized as "substantially - * later". This is about 1/128 sec, but above 1 tick counter increment. - */ -#define SK_RLMT_BC_DELTA (1 + ((SK_TICKS_PER_SEC >> 7) > SK_TICK_INCR ? \ - (SK_TICKS_PER_SEC >> 7) : SK_TICK_INCR)) - -/* ----- Private RLMT defaults ----- */ - -#define SK_RLMT_DEF_PREF_PORT 0 /* "Lower" port. */ -#define SK_RLMT_DEF_MODE SK_RLMT_CHECK_LINK /* Default RLMT Mode. */ - -/* ----- Private RLMT checking states ----- */ - -#define SK_RLMT_RCS_SEG 1 /* RLMT Check State: check seg. */ -#define SK_RLMT_RCS_START_SEG 2 /* RLMT Check State: start check seg. */ -#define SK_RLMT_RCS_SEND_SEG 4 /* RLMT Check State: send BPDU packet */ -#define SK_RLMT_RCS_REPORT_SEG 8 /* RLMT Check State: report seg. */ - -/* ----- Private PORT checking states ----- */ - -#define SK_RLMT_PCS_TX 1 /* Port Check State: check tx. */ -#define SK_RLMT_PCS_RX 2 /* Port Check State: check rx. */ - -/* ----- Private PORT events ----- */ - -/* Note: Update simulation when changing these. */ -#define SK_RLMT_PORTSTART_TIM 1100 /* Port start timeout. */ -#define SK_RLMT_PORTUP_TIM 1101 /* Port can now go up. */ -#define SK_RLMT_PORTDOWN_RX_TIM 1102 /* Port did not receive once ... */ -#define SK_RLMT_PORTDOWN 1103 /* Port went down. */ -#define SK_RLMT_PORTDOWN_TX_TIM 1104 /* Partner did not receive ... */ - -/* ----- Private RLMT events ----- */ - -/* Note: Update simulation when changing these. */ -#define SK_RLMT_TIM 2100 /* RLMT timeout. */ -#define SK_RLMT_SEG_TIM 2101 /* RLMT segmentation check timeout. */ - -#define TO_SHORTEN(tim) ((tim) / 2) - -/* Error numbers and messages. */ -#define SKERR_RLMT_E001 (SK_ERRBASE_RLMT + 0) -#define SKERR_RLMT_E001_MSG "No Packet." -#define SKERR_RLMT_E002 (SKERR_RLMT_E001 + 1) -#define SKERR_RLMT_E002_MSG "Short Packet." -#define SKERR_RLMT_E003 (SKERR_RLMT_E002 + 1) -#define SKERR_RLMT_E003_MSG "Unknown RLMT event." -#define SKERR_RLMT_E004 (SKERR_RLMT_E003 + 1) -#define SKERR_RLMT_E004_MSG "PortsUp incorrect." -#define SKERR_RLMT_E005 (SKERR_RLMT_E004 + 1) -#define SKERR_RLMT_E005_MSG \ - "Net seems to be segmented (different root bridges are reported on the ports)." -#define SKERR_RLMT_E006 (SKERR_RLMT_E005 + 1) -#define SKERR_RLMT_E006_MSG "Duplicate MAC Address detected." -#define SKERR_RLMT_E007 (SKERR_RLMT_E006 + 1) -#define SKERR_RLMT_E007_MSG "LinksUp incorrect." -#define SKERR_RLMT_E008 (SKERR_RLMT_E007 + 1) -#define SKERR_RLMT_E008_MSG "Port not started but link came up." -#define SKERR_RLMT_E009 (SKERR_RLMT_E008 + 1) -#define SKERR_RLMT_E009_MSG "Corrected illegal setting of Preferred Port." -#define SKERR_RLMT_E010 (SKERR_RLMT_E009 + 1) -#define SKERR_RLMT_E010_MSG "Ignored illegal Preferred Port." - -/* LLC field values. */ -#define LLC_COMMAND_RESPONSE_BIT 1 -#define LLC_TEST_COMMAND 0xE3 -#define LLC_UI 0x03 - -/* RLMT Packet fields. */ -#define SK_RLMT_DSAP 0 -#define SK_RLMT_SSAP 0 -#define SK_RLMT_CTRL (LLC_TEST_COMMAND) -#define SK_RLMT_INDICATOR0 0x53 /* S */ -#define SK_RLMT_INDICATOR1 0x4B /* K */ -#define SK_RLMT_INDICATOR2 0x2D /* - */ -#define SK_RLMT_INDICATOR3 0x52 /* R */ -#define SK_RLMT_INDICATOR4 0x4C /* L */ -#define SK_RLMT_INDICATOR5 0x4D /* M */ -#define SK_RLMT_INDICATOR6 0x54 /* T */ -#define SK_RLMT_PACKET_VERSION 0 - -/* RLMT SPT Flag values. */ -#define SK_RLMT_SPT_FLAG_CHANGE 0x01 -#define SK_RLMT_SPT_FLAG_CHANGE_ACK 0x80 - -/* RLMT SPT Packet fields. */ -#define SK_RLMT_SPT_DSAP 0x42 -#define SK_RLMT_SPT_SSAP 0x42 -#define SK_RLMT_SPT_CTRL (LLC_UI) -#define SK_RLMT_SPT_PROTOCOL_ID0 0x00 -#define SK_RLMT_SPT_PROTOCOL_ID1 0x00 -#define SK_RLMT_SPT_PROTOCOL_VERSION_ID 0x00 -#define SK_RLMT_SPT_BPDU_TYPE 0x00 -#define SK_RLMT_SPT_FLAGS 0x00 /* ?? */ -#define SK_RLMT_SPT_ROOT_ID0 0xFF /* Lowest possible priority. */ -#define SK_RLMT_SPT_ROOT_ID1 0xFF /* Lowest possible priority. */ - -/* Remaining 6 bytes will be the current port address. */ -#define SK_RLMT_SPT_ROOT_PATH_COST0 0x00 -#define SK_RLMT_SPT_ROOT_PATH_COST1 0x00 -#define SK_RLMT_SPT_ROOT_PATH_COST2 0x00 -#define SK_RLMT_SPT_ROOT_PATH_COST3 0x00 -#define SK_RLMT_SPT_BRIDGE_ID0 0xFF /* Lowest possible priority. */ -#define SK_RLMT_SPT_BRIDGE_ID1 0xFF /* Lowest possible priority. */ - -/* Remaining 6 bytes will be the current port address. */ -#define SK_RLMT_SPT_PORT_ID0 0xFF /* Lowest possible priority. */ -#define SK_RLMT_SPT_PORT_ID1 0xFF /* Lowest possible priority. */ -#define SK_RLMT_SPT_MSG_AGE0 0x00 -#define SK_RLMT_SPT_MSG_AGE1 0x00 -#define SK_RLMT_SPT_MAX_AGE0 0x00 -#define SK_RLMT_SPT_MAX_AGE1 0xFF -#define SK_RLMT_SPT_HELLO_TIME0 0x00 -#define SK_RLMT_SPT_HELLO_TIME1 0xFF -#define SK_RLMT_SPT_FWD_DELAY0 0x00 -#define SK_RLMT_SPT_FWD_DELAY1 0x40 - -/* Size defines. */ -#define SK_RLMT_MIN_PACKET_SIZE 34 -#define SK_RLMT_MAX_PACKET_SIZE (SK_RLMT_MAX_TX_BUF_SIZE) -#define SK_PACKET_DATA_LEN (SK_RLMT_MAX_PACKET_SIZE - \ - SK_RLMT_MIN_PACKET_SIZE) - -/* ----- RLMT packet types ----- */ -#define SK_PACKET_ANNOUNCE 1 /* Port announcement. */ -#define SK_PACKET_ALIVE 2 /* Alive packet to port. */ -#define SK_PACKET_ADDR_CHANGED 3 /* Port address changed. */ -#define SK_PACKET_CHECK_TX 4 /* Check your tx line. */ - -#ifdef SK_LITTLE_ENDIAN -#define SK_U16_TO_NETWORK_ORDER(Val,Addr) { \ - SK_U8 *_Addr = (SK_U8*)(Addr); \ - SK_U16 _Val = (SK_U16)(Val); \ - *_Addr++ = (SK_U8)(_Val >> 8); \ - *_Addr = (SK_U8)(_Val & 0xFF); \ -} -#endif /* SK_LITTLE_ENDIAN */ - -#ifdef SK_BIG_ENDIAN -#define SK_U16_TO_NETWORK_ORDER(Val,Addr) (*(SK_U16*)(Addr) = (SK_U16)(Val)) -#endif /* SK_BIG_ENDIAN */ - -#define AUTONEG_FAILED SK_FALSE -#define AUTONEG_SUCCESS SK_TRUE - - -/* typedefs *******************************************************************/ - -/* RLMT packet. Length: SK_RLMT_MAX_PACKET_SIZE (60) bytes. */ -typedef struct s_RlmtPacket { - SK_U8 DstAddr[SK_MAC_ADDR_LEN]; - SK_U8 SrcAddr[SK_MAC_ADDR_LEN]; - SK_U8 TypeLen[2]; - SK_U8 DSap; - SK_U8 SSap; - SK_U8 Ctrl; - SK_U8 Indicator[7]; - SK_U8 RlmtPacketType[2]; - SK_U8 Align1[2]; - SK_U8 Random[4]; /* Random value of requesting(!) station. */ - SK_U8 RlmtPacketVersion[2]; /* RLMT Packet version. */ - SK_U8 Data[SK_PACKET_DATA_LEN]; -} SK_RLMT_PACKET; - -typedef struct s_SpTreeRlmtPacket { - SK_U8 DstAddr[SK_MAC_ADDR_LEN]; - SK_U8 SrcAddr[SK_MAC_ADDR_LEN]; - SK_U8 TypeLen[2]; - SK_U8 DSap; - SK_U8 SSap; - SK_U8 Ctrl; - SK_U8 ProtocolId[2]; - SK_U8 ProtocolVersionId; - SK_U8 BpduType; - SK_U8 Flags; - SK_U8 RootId[8]; - SK_U8 RootPathCost[4]; - SK_U8 BridgeId[8]; - SK_U8 PortId[2]; - SK_U8 MessageAge[2]; - SK_U8 MaxAge[2]; - SK_U8 HelloTime[2]; - SK_U8 ForwardDelay[2]; -} SK_SPTREE_PACKET; - -/* global variables ***********************************************************/ - -SK_MAC_ADDR SkRlmtMcAddr = {{0x01, 0x00, 0x5A, 0x52, 0x4C, 0x4D}}; -SK_MAC_ADDR BridgeMcAddr = {{0x01, 0x80, 0xC2, 0x00, 0x00, 0x00}}; - -/* local variables ************************************************************/ - -/* None. */ - -/* functions ******************************************************************/ - -RLMT_STATIC void SkRlmtCheckSwitch( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 NetIdx); -RLMT_STATIC void SkRlmtCheckSeg( - SK_AC *pAC, - SK_IOC IoC, - SK_U32 NetIdx); -RLMT_STATIC void SkRlmtEvtSetNets( - SK_AC *pAC, - SK_IOC IoC, - SK_EVPARA Para); - -/****************************************************************************** - * - * SkRlmtInit - initialize data, set state to init - * - * Description: - * - * SK_INIT_DATA - * ============ - * - * This routine initializes all RLMT-related variables to a known state. - * The initial state is SK_RLMT_RS_INIT. - * All ports are initialized to SK_RLMT_PS_INIT. - * - * - * SK_INIT_IO - * ========== - * - * Nothing. - * - * - * SK_INIT_RUN - * =========== - * - * Determine the adapter's random value. - * Set the hw registers, the "logical MAC address", the - * RLMT multicast address, and eventually the BPDU multicast address. - * - * Context: - * init, pageable - * - * Returns: - * Nothing. - */ -void SkRlmtInit( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int Level) /* Initialization Level */ -{ - SK_U32 i, j; - SK_U64 Random; - SK_EVPARA Para; - SK_MAC_ADDR VirtualMacAddress; - SK_MAC_ADDR PhysicalAMacAddress; - SK_BOOL VirtualMacAddressSet; - SK_BOOL PhysicalAMacAddressSet; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_INIT, - ("RLMT Init level %d.\n", Level)) - - switch (Level) { - case SK_INIT_DATA: /* Initialize data structures. */ - SK_MEMSET((char *)&pAC->Rlmt, 0, sizeof(SK_RLMT)); - - for (i = 0; i < SK_MAX_MACS; i++) { - pAC->Rlmt.Port[i].PortState = SK_RLMT_PS_INIT; - pAC->Rlmt.Port[i].LinkDown = SK_TRUE; - pAC->Rlmt.Port[i].PortDown = SK_TRUE; - pAC->Rlmt.Port[i].PortStarted = SK_FALSE; - pAC->Rlmt.Port[i].PortNoRx = SK_FALSE; - pAC->Rlmt.Port[i].RootIdSet = SK_FALSE; - pAC->Rlmt.Port[i].PortNumber = i; - pAC->Rlmt.Port[i].Net = &pAC->Rlmt.Net[0]; - pAC->Rlmt.Port[i].AddrPort = &pAC->Addr.Port[i]; - } - - pAC->Rlmt.NumNets = 1; - for (i = 0; i < SK_MAX_NETS; i++) { - pAC->Rlmt.Net[i].RlmtState = SK_RLMT_RS_INIT; - pAC->Rlmt.Net[i].RootIdSet = SK_FALSE; - pAC->Rlmt.Net[i].PrefPort = SK_RLMT_DEF_PREF_PORT; - pAC->Rlmt.Net[i].Preference = 0xFFFFFFFF; /* Automatic. */ - /* Just assuming. */ - pAC->Rlmt.Net[i].ActivePort = pAC->Rlmt.Net[i].PrefPort; - pAC->Rlmt.Net[i].RlmtMode = SK_RLMT_DEF_MODE; - pAC->Rlmt.Net[i].TimeoutValue = SK_RLMT_DEF_TO_VAL; - pAC->Rlmt.Net[i].NetNumber = i; - } - - pAC->Rlmt.Net[0].Port[0] = &pAC->Rlmt.Port[0]; - pAC->Rlmt.Net[0].Port[1] = &pAC->Rlmt.Port[1]; -#if SK_MAX_NETS > 1 - pAC->Rlmt.Net[1].Port[0] = &pAC->Rlmt.Port[1]; -#endif /* SK_MAX_NETS > 1 */ - break; - - case SK_INIT_IO: /* GIMacsFound first available here. */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_INIT, - ("RLMT: %d MACs were detected.\n", pAC->GIni.GIMacsFound)) - - pAC->Rlmt.Net[0].NumPorts = pAC->GIni.GIMacsFound; - - /* Initialize HW registers? */ - if (pAC->GIni.GIMacsFound == 1) { - Para.Para32[0] = SK_RLMT_MODE_CLS; - Para.Para32[1] = 0; - (void)SkRlmtEvent(pAC, IoC, SK_RLMT_MODE_CHANGE, Para); - } - break; - - case SK_INIT_RUN: - /* Ensure RLMT is set to one net. */ - if (pAC->Rlmt.NumNets > 1) { - Para.Para32[0] = 1; - Para.Para32[1] = -1; - SkRlmtEvtSetNets(pAC, IoC, Para); - } - - for (i = 0; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - Random = SkOsGetTime(pAC); - *(SK_U32*)&pAC->Rlmt.Port[i].Random = *(SK_U32*)&Random; - - for (j = 0; j < 4; j++) { - pAC->Rlmt.Port[i].Random[j] ^= pAC->Rlmt.Port[i].AddrPort-> - CurrentMacAddress.a[SK_MAC_ADDR_LEN - 1 - j]; - } - - (void)SkAddrMcClear(pAC, IoC, i, SK_ADDR_PERMANENT | SK_MC_SW_ONLY); - - /* Add RLMT MC address. */ - (void)SkAddrMcAdd(pAC, IoC, i, &SkRlmtMcAddr, SK_ADDR_PERMANENT); - - if (pAC->Rlmt.Net[0].RlmtMode & SK_RLMT_CHECK_SEG) { - /* Add BPDU MC address. */ - (void)SkAddrMcAdd(pAC, IoC, i, &BridgeMcAddr, SK_ADDR_PERMANENT); - } - - (void)SkAddrMcUpdate(pAC, IoC, i); - } - - VirtualMacAddressSet = SK_FALSE; - /* Read virtual MAC address from Control Register File. */ - for (j = 0; j < SK_MAC_ADDR_LEN; j++) { - - SK_IN8(IoC, B2_MAC_1 + j, &VirtualMacAddress.a[j]); - VirtualMacAddressSet |= VirtualMacAddress.a[j]; - } - - PhysicalAMacAddressSet = SK_FALSE; - /* Read physical MAC address for MAC A from Control Register File. */ - for (j = 0; j < SK_MAC_ADDR_LEN; j++) { - - SK_IN8(IoC, B2_MAC_2 + j, &PhysicalAMacAddress.a[j]); - PhysicalAMacAddressSet |= PhysicalAMacAddress.a[j]; - } - - /* check if the two mac addresses contain reasonable values */ - if (!VirtualMacAddressSet || !PhysicalAMacAddressSet) { - - pAC->Rlmt.RlmtOff = SK_TRUE; - } - - /* if the two mac addresses are equal switch off the RLMT_PRE_LOOKAHEAD - and the RLMT_LOOKAHEAD macros */ - else if (SK_ADDR_EQUAL(PhysicalAMacAddress.a, VirtualMacAddress.a)) { - - pAC->Rlmt.RlmtOff = SK_TRUE; - } - else { - pAC->Rlmt.RlmtOff = SK_FALSE; - } - break; - - default: /* error */ - break; - } - return; -} /* SkRlmtInit */ - - -/****************************************************************************** - * - * SkRlmtBuildCheckChain - build the check chain - * - * Description: - * This routine builds the local check chain: - * - Each port that is up checks the next port. - * - The last port that is up checks the first port that is up. - * - * Notes: - * - Currently only local ports are considered when building the chain. - * - Currently the SuspectState is just reset; - * it would be better to save it ... - * - * Context: - * runtime, pageable? - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtBuildCheckChain( -SK_AC *pAC, /* Adapter Context */ -SK_U32 NetIdx) /* Net Number */ -{ - SK_U32 i; - SK_U32 NumMacsUp; - SK_RLMT_PORT * FirstMacUp; - SK_RLMT_PORT * PrevMacUp; - - FirstMacUp = NULL; - PrevMacUp = NULL; - - if (!(pAC->Rlmt.Net[NetIdx].RlmtMode & SK_RLMT_CHECK_LOC_LINK)) { - for (i = 0; i < pAC->Rlmt.Net[i].NumPorts; i++) { - pAC->Rlmt.Net[NetIdx].Port[i]->PortsChecked = 0; - } - return; /* Done. */ - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SkRlmtBuildCheckChain.\n")) - - NumMacsUp = 0; - - for (i = 0; i < pAC->Rlmt.Net[NetIdx].NumPorts; i++) { - pAC->Rlmt.Net[NetIdx].Port[i]->PortsChecked = 0; - pAC->Rlmt.Net[NetIdx].Port[i]->PortsSuspect = 0; - pAC->Rlmt.Net[NetIdx].Port[i]->CheckingState &= - ~(SK_RLMT_PCS_RX | SK_RLMT_PCS_TX); - - /* - * If more than two links are detected we should consider - * checking at least two other ports: - * 1. the next port that is not LinkDown and - * 2. the next port that is not PortDown. - */ - if (!pAC->Rlmt.Net[NetIdx].Port[i]->LinkDown) { - if (NumMacsUp == 0) { - FirstMacUp = pAC->Rlmt.Net[NetIdx].Port[i]; - } - else { - PrevMacUp->PortCheck[ - pAC->Rlmt.Net[NetIdx].Port[i]->PortsChecked].CheckAddr = - pAC->Rlmt.Net[NetIdx].Port[i]->AddrPort->CurrentMacAddress; - PrevMacUp->PortCheck[ - PrevMacUp->PortsChecked].SuspectTx = SK_FALSE; - PrevMacUp->PortsChecked++; - } - PrevMacUp = pAC->Rlmt.Net[NetIdx].Port[i]; - NumMacsUp++; - } - } - - if (NumMacsUp > 1) { - PrevMacUp->PortCheck[PrevMacUp->PortsChecked].CheckAddr = - FirstMacUp->AddrPort->CurrentMacAddress; - PrevMacUp->PortCheck[PrevMacUp->PortsChecked].SuspectTx = - SK_FALSE; - PrevMacUp->PortsChecked++; - } - -#ifdef DEBUG - for (i = 0; i < pAC->Rlmt.Net[NetIdx].NumPorts; i++) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Port %d checks %d other ports: %2X.\n", i, - pAC->Rlmt.Net[NetIdx].Port[i]->PortsChecked, - pAC->Rlmt.Net[NetIdx].Port[i]->PortCheck[0].CheckAddr.a[5])) - } -#endif /* DEBUG */ - - return; -} /* SkRlmtBuildCheckChain */ - - -/****************************************************************************** - * - * SkRlmtBuildPacket - build an RLMT packet - * - * Description: - * This routine sets up an RLMT packet. - * - * Context: - * runtime, pageable? - * - * Returns: - * NULL or pointer to RLMT mbuf - */ -RLMT_STATIC SK_MBUF *SkRlmtBuildPacket( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 PortNumber, /* Sending port */ -SK_U16 PacketType, /* RLMT packet type */ -SK_MAC_ADDR *SrcAddr, /* Source address */ -SK_MAC_ADDR *DestAddr) /* Destination address */ -{ - int i; - SK_U16 Length; - SK_MBUF *pMb; - SK_RLMT_PACKET *pPacket; - -#ifdef DEBUG - SK_U8 CheckSrc = 0; - SK_U8 CheckDest = 0; - - for (i = 0; i < SK_MAC_ADDR_LEN; ++i) { - CheckSrc |= SrcAddr->a[i]; - CheckDest |= DestAddr->a[i]; - } - - if ((CheckSrc == 0) || (CheckDest == 0)) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_ERR, - ("SkRlmtBuildPacket: Invalid %s%saddr.\n", - (CheckSrc == 0 ? "Src" : ""), (CheckDest == 0 ? "Dest" : ""))) - } -#endif - - if ((pMb = SkDrvAllocRlmtMbuf(pAC, IoC, SK_RLMT_MAX_PACKET_SIZE)) != NULL) { - pPacket = (SK_RLMT_PACKET*)pMb->pData; - for (i = 0; i < SK_MAC_ADDR_LEN; i++) { - pPacket->DstAddr[i] = DestAddr->a[i]; - pPacket->SrcAddr[i] = SrcAddr->a[i]; - } - pPacket->DSap = SK_RLMT_DSAP; - pPacket->SSap = SK_RLMT_SSAP; - pPacket->Ctrl = SK_RLMT_CTRL; - pPacket->Indicator[0] = SK_RLMT_INDICATOR0; - pPacket->Indicator[1] = SK_RLMT_INDICATOR1; - pPacket->Indicator[2] = SK_RLMT_INDICATOR2; - pPacket->Indicator[3] = SK_RLMT_INDICATOR3; - pPacket->Indicator[4] = SK_RLMT_INDICATOR4; - pPacket->Indicator[5] = SK_RLMT_INDICATOR5; - pPacket->Indicator[6] = SK_RLMT_INDICATOR6; - - SK_U16_TO_NETWORK_ORDER(PacketType, &pPacket->RlmtPacketType[0]); - - for (i = 0; i < 4; i++) { - pPacket->Random[i] = pAC->Rlmt.Port[PortNumber].Random[i]; - } - - SK_U16_TO_NETWORK_ORDER( - SK_RLMT_PACKET_VERSION, &pPacket->RlmtPacketVersion[0]); - - for (i = 0; i < SK_PACKET_DATA_LEN; i++) { - pPacket->Data[i] = 0x00; - } - - Length = SK_RLMT_MAX_PACKET_SIZE; /* Or smaller. */ - pMb->Length = Length; - pMb->PortIdx = PortNumber; - Length -= 14; - SK_U16_TO_NETWORK_ORDER(Length, &pPacket->TypeLen[0]); - - if (PacketType == SK_PACKET_ALIVE) { - pAC->Rlmt.Port[PortNumber].TxHelloCts++; - } - } - - return (pMb); -} /* SkRlmtBuildPacket */ - - -/****************************************************************************** - * - * SkRlmtBuildSpanningTreePacket - build spanning tree check packet - * - * Description: - * This routine sets up a BPDU packet for spanning tree check. - * - * Context: - * runtime, pageable? - * - * Returns: - * NULL or pointer to RLMT mbuf - */ -RLMT_STATIC SK_MBUF *SkRlmtBuildSpanningTreePacket( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 PortNumber) /* Sending port */ -{ - unsigned i; - SK_U16 Length; - SK_MBUF *pMb; - SK_SPTREE_PACKET *pSPacket; - - if ((pMb = SkDrvAllocRlmtMbuf(pAC, IoC, SK_RLMT_MAX_PACKET_SIZE)) != - NULL) { - pSPacket = (SK_SPTREE_PACKET*)pMb->pData; - for (i = 0; i < SK_MAC_ADDR_LEN; i++) { - pSPacket->DstAddr[i] = BridgeMcAddr.a[i]; - pSPacket->SrcAddr[i] = - pAC->Addr.Port[PortNumber].CurrentMacAddress.a[i]; - } - pSPacket->DSap = SK_RLMT_SPT_DSAP; - pSPacket->SSap = SK_RLMT_SPT_SSAP; - pSPacket->Ctrl = SK_RLMT_SPT_CTRL; - - pSPacket->ProtocolId[0] = SK_RLMT_SPT_PROTOCOL_ID0; - pSPacket->ProtocolId[1] = SK_RLMT_SPT_PROTOCOL_ID1; - pSPacket->ProtocolVersionId = SK_RLMT_SPT_PROTOCOL_VERSION_ID; - pSPacket->BpduType = SK_RLMT_SPT_BPDU_TYPE; - pSPacket->Flags = SK_RLMT_SPT_FLAGS; - pSPacket->RootId[0] = SK_RLMT_SPT_ROOT_ID0; - pSPacket->RootId[1] = SK_RLMT_SPT_ROOT_ID1; - pSPacket->RootPathCost[0] = SK_RLMT_SPT_ROOT_PATH_COST0; - pSPacket->RootPathCost[1] = SK_RLMT_SPT_ROOT_PATH_COST1; - pSPacket->RootPathCost[2] = SK_RLMT_SPT_ROOT_PATH_COST2; - pSPacket->RootPathCost[3] = SK_RLMT_SPT_ROOT_PATH_COST3; - pSPacket->BridgeId[0] = SK_RLMT_SPT_BRIDGE_ID0; - pSPacket->BridgeId[1] = SK_RLMT_SPT_BRIDGE_ID1; - - /* - * Use logical MAC address as bridge ID and filter these packets - * on receive. - */ - for (i = 0; i < SK_MAC_ADDR_LEN; i++) { - pSPacket->BridgeId[i + 2] = pSPacket->RootId[i + 2] = - pAC->Addr.Net[pAC->Rlmt.Port[PortNumber].Net->NetNumber]. - CurrentMacAddress.a[i]; - } - pSPacket->PortId[0] = SK_RLMT_SPT_PORT_ID0; - pSPacket->PortId[1] = SK_RLMT_SPT_PORT_ID1; - pSPacket->MessageAge[0] = SK_RLMT_SPT_MSG_AGE0; - pSPacket->MessageAge[1] = SK_RLMT_SPT_MSG_AGE1; - pSPacket->MaxAge[0] = SK_RLMT_SPT_MAX_AGE0; - pSPacket->MaxAge[1] = SK_RLMT_SPT_MAX_AGE1; - pSPacket->HelloTime[0] = SK_RLMT_SPT_HELLO_TIME0; - pSPacket->HelloTime[1] = SK_RLMT_SPT_HELLO_TIME1; - pSPacket->ForwardDelay[0] = SK_RLMT_SPT_FWD_DELAY0; - pSPacket->ForwardDelay[1] = SK_RLMT_SPT_FWD_DELAY1; - - Length = SK_RLMT_MAX_PACKET_SIZE; /* Or smaller. */ - pMb->Length = Length; - pMb->PortIdx = PortNumber; - Length -= 14; - SK_U16_TO_NETWORK_ORDER(Length, &pSPacket->TypeLen[0]); - - pAC->Rlmt.Port[PortNumber].TxSpHelloReqCts++; - } - - return (pMb); -} /* SkRlmtBuildSpanningTreePacket */ - - -/****************************************************************************** - * - * SkRlmtSend - build and send check packets - * - * Description: - * Depending on the RLMT state and the checking state, several packets - * are sent through the indicated port. - * - * Context: - * runtime, pageable? - * - * Returns: - * Nothing. - */ -RLMT_STATIC void SkRlmtSend( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 PortNumber) /* Sending port */ -{ - unsigned j; - SK_EVPARA Para; - SK_RLMT_PORT *pRPort; - - pRPort = &pAC->Rlmt.Port[PortNumber]; - if (pAC->Rlmt.Port[PortNumber].Net->RlmtMode & SK_RLMT_CHECK_LOC_LINK) { - if (pRPort->CheckingState & (SK_RLMT_PCS_TX | SK_RLMT_PCS_RX)) { - /* Port is suspicious. Send the RLMT packet to the RLMT mc addr. */ - if ((Para.pParaPtr = SkRlmtBuildPacket(pAC, IoC, PortNumber, - SK_PACKET_ALIVE, &pAC->Addr.Port[PortNumber].CurrentMacAddress, - &SkRlmtMcAddr)) != NULL) { - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para); - } - } - else { - /* - * Send a directed RLMT packet to all ports that are - * checked by the indicated port. - */ - for (j = 0; j < pRPort->PortsChecked; j++) { - if ((Para.pParaPtr = SkRlmtBuildPacket(pAC, IoC, PortNumber, - SK_PACKET_ALIVE, &pAC->Addr.Port[PortNumber].CurrentMacAddress, - &pRPort->PortCheck[j].CheckAddr)) != NULL) { - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para); - } - } - } - } - - if ((pAC->Rlmt.Port[PortNumber].Net->RlmtMode & SK_RLMT_CHECK_SEG) && - (pAC->Rlmt.Port[PortNumber].Net->CheckingState & SK_RLMT_RCS_SEND_SEG)) { - /* - * Send a BPDU packet to make a connected switch tell us - * the correct root bridge. - */ - if ((Para.pParaPtr = - SkRlmtBuildSpanningTreePacket(pAC, IoC, PortNumber)) != NULL) { - pAC->Rlmt.Port[PortNumber].Net->CheckingState &= ~SK_RLMT_RCS_SEND_SEG; - pRPort->RootIdSet = SK_FALSE; - - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para); - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_TX, - ("SkRlmtSend: BPDU Packet on Port %u.\n", PortNumber)) - } - } - return; -} /* SkRlmtSend */ - - -/****************************************************************************** - * - * SkRlmtPortReceives - check if port is (going) down and bring it up - * - * Description: - * This routine checks if a port who received a non-BPDU packet - * needs to go up or needs to be stopped going down. - * - * Context: - * runtime, pageable? - * - * Returns: - * Nothing. - */ -RLMT_STATIC void SkRlmtPortReceives( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 PortNumber) /* Port to check */ -{ - SK_RLMT_PORT *pRPort; - SK_EVPARA Para; - - pRPort = &pAC->Rlmt.Port[PortNumber]; - pRPort->PortNoRx = SK_FALSE; - - if ((pRPort->PortState == SK_RLMT_PS_DOWN) && - !(pRPort->CheckingState & SK_RLMT_PCS_TX)) { - /* - * Port is marked down (rx), but received a non-BPDU packet. - * Bring it up. - */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Received on PortDown.\n")) - - pRPort->PortState = SK_RLMT_PS_GOING_UP; - pRPort->GuTimeStamp = SkOsGetTime(pAC); - Para.Para32[0] = PortNumber; - Para.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pRPort->UpTimer, SK_RLMT_PORTUP_TIM_VAL, - SKGE_RLMT, SK_RLMT_PORTUP_TIM, Para); - pRPort->CheckingState &= ~SK_RLMT_PCS_RX; - /* pAC->Rlmt.CheckSwitch = SK_TRUE; */ - SkRlmtCheckSwitch(pAC, IoC, pRPort->Net->NetNumber); - } /* PortDown && !SuspectTx */ - else if (pRPort->CheckingState & SK_RLMT_PCS_RX) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Stop bringing port down.\n")) - SkTimerStop(pAC, IoC, &pRPort->DownRxTimer); - pRPort->CheckingState &= ~SK_RLMT_PCS_RX; - /* pAC->Rlmt.CheckSwitch = SK_TRUE; */ - SkRlmtCheckSwitch(pAC, IoC, pRPort->Net->NetNumber); - } /* PortGoingDown */ - - return; -} /* SkRlmtPortReceives */ - - -/****************************************************************************** - * - * SkRlmtPacketReceive - receive a packet for closer examination - * - * Description: - * This routine examines a packet more closely than SK_RLMT_LOOKAHEAD. - * - * Context: - * runtime, pageable? - * - * Returns: - * Nothing. - */ -RLMT_STATIC void SkRlmtPacketReceive( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_MBUF *pMb) /* Received packet */ -{ -#ifdef xDEBUG - extern void DumpData(char *p, int size); -#endif /* DEBUG */ - int i; - unsigned j; - SK_U16 PacketType; - SK_U32 PortNumber; - SK_ADDR_PORT *pAPort; - SK_RLMT_PORT *pRPort; - SK_RLMT_PACKET *pRPacket; - SK_SPTREE_PACKET *pSPacket; - SK_EVPARA Para; - - PortNumber = pMb->PortIdx; - pAPort = &pAC->Addr.Port[PortNumber]; - pRPort = &pAC->Rlmt.Port[PortNumber]; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: PortNumber == %d.\n", PortNumber)) - - pRPacket = (SK_RLMT_PACKET*)pMb->pData; - pSPacket = (SK_SPTREE_PACKET*)pRPacket; - -#ifdef xDEBUG - DumpData((char *)pRPacket, 32); -#endif /* DEBUG */ - - if ((pRPort->PacketsPerTimeSlot - pRPort->BpduPacketsPerTimeSlot) != 0) { - SkRlmtPortReceives(pAC, IoC, PortNumber); - } - - /* Check destination address. */ - - if (!SK_ADDR_EQUAL(pAPort->CurrentMacAddress.a, pRPacket->DstAddr) && - !SK_ADDR_EQUAL(SkRlmtMcAddr.a, pRPacket->DstAddr) && - !SK_ADDR_EQUAL(BridgeMcAddr.a, pRPacket->DstAddr)) { - - /* Not sent to current MAC or registered MC address => Trash it. */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Not for me.\n")) - - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - return; - } - else if (SK_ADDR_EQUAL(pAPort->CurrentMacAddress.a, pRPacket->SrcAddr)) { - - /* - * Was sent by same port (may happen during port switching - * or in case of duplicate MAC addresses). - */ - - /* - * Check for duplicate address here: - * If Packet.Random != My.Random => DupAddr. - */ - for (i = 3; i >= 0; i--) { - if (pRPort->Random[i] != pRPacket->Random[i]) { - break; - } - } - - /* - * CAUTION: Do not check for duplicate MAC address in RLMT Alive Reply - * packets (they have the LLC_COMMAND_RESPONSE_BIT set in - * pRPacket->SSap). - */ - if (i >= 0 && pRPacket->DSap == SK_RLMT_DSAP && - pRPacket->Ctrl == SK_RLMT_CTRL && - pRPacket->SSap == SK_RLMT_SSAP && - pRPacket->Indicator[0] == SK_RLMT_INDICATOR0 && - pRPacket->Indicator[1] == SK_RLMT_INDICATOR1 && - pRPacket->Indicator[2] == SK_RLMT_INDICATOR2 && - pRPacket->Indicator[3] == SK_RLMT_INDICATOR3 && - pRPacket->Indicator[4] == SK_RLMT_INDICATOR4 && - pRPacket->Indicator[5] == SK_RLMT_INDICATOR5 && - pRPacket->Indicator[6] == SK_RLMT_INDICATOR6) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Duplicate MAC Address.\n")) - - /* Error Log entry. */ - SK_ERR_LOG(pAC, SK_ERRCL_COMM, SKERR_RLMT_E006, SKERR_RLMT_E006_MSG); - } - else { - /* Simply trash it. */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Sent by me.\n")) - } - - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - return; - } - - /* Check SuspectTx entries. */ - if (pRPort->PortsSuspect > 0) { - for (j = 0; j < pRPort->PortsChecked; j++) { - if (pRPort->PortCheck[j].SuspectTx && - SK_ADDR_EQUAL( - pRPacket->SrcAddr, pRPort->PortCheck[j].CheckAddr.a)) { - pRPort->PortCheck[j].SuspectTx = SK_FALSE; - pRPort->PortsSuspect--; - break; - } - } - } - - /* Determine type of packet. */ - if (pRPacket->DSap == SK_RLMT_DSAP && - pRPacket->Ctrl == SK_RLMT_CTRL && - (pRPacket->SSap & ~LLC_COMMAND_RESPONSE_BIT) == SK_RLMT_SSAP && - pRPacket->Indicator[0] == SK_RLMT_INDICATOR0 && - pRPacket->Indicator[1] == SK_RLMT_INDICATOR1 && - pRPacket->Indicator[2] == SK_RLMT_INDICATOR2 && - pRPacket->Indicator[3] == SK_RLMT_INDICATOR3 && - pRPacket->Indicator[4] == SK_RLMT_INDICATOR4 && - pRPacket->Indicator[5] == SK_RLMT_INDICATOR5 && - pRPacket->Indicator[6] == SK_RLMT_INDICATOR6) { - - /* It's an RLMT packet. */ - PacketType = (SK_U16)((pRPacket->RlmtPacketType[0] << 8) | - pRPacket->RlmtPacketType[1]); - - switch (PacketType) { - case SK_PACKET_ANNOUNCE: /* Not yet used. */ -#if 0 - /* Build the check chain. */ - SkRlmtBuildCheckChain(pAC); -#endif /* 0 */ - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Announce.\n")) - - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - break; - - case SK_PACKET_ALIVE: - if (pRPacket->SSap & LLC_COMMAND_RESPONSE_BIT) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Alive Reply.\n")) - - if (!(pAC->Addr.Port[PortNumber].PromMode & SK_PROM_MODE_LLC) || - SK_ADDR_EQUAL( - pRPacket->DstAddr, pAPort->CurrentMacAddress.a)) { - /* Obviously we could send something. */ - if (pRPort->CheckingState & SK_RLMT_PCS_TX) { - pRPort->CheckingState &= ~SK_RLMT_PCS_TX; - SkTimerStop(pAC, IoC, &pRPort->DownTxTimer); - } - - if ((pRPort->PortState == SK_RLMT_PS_DOWN) && - !(pRPort->CheckingState & SK_RLMT_PCS_RX)) { - pRPort->PortState = SK_RLMT_PS_GOING_UP; - pRPort->GuTimeStamp = SkOsGetTime(pAC); - - SkTimerStop(pAC, IoC, &pRPort->DownTxTimer); - - Para.Para32[0] = PortNumber; - Para.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pRPort->UpTimer, - SK_RLMT_PORTUP_TIM_VAL, SKGE_RLMT, - SK_RLMT_PORTUP_TIM, Para); - } - } - - /* Mark sending port as alive? */ - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - } - else { /* Alive Request Packet. */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Alive Request.\n")) - - pRPort->RxHelloCts++; - - /* Answer. */ - for (i = 0; i < SK_MAC_ADDR_LEN; i++) { - pRPacket->DstAddr[i] = pRPacket->SrcAddr[i]; - pRPacket->SrcAddr[i] = - pAC->Addr.Port[PortNumber].CurrentMacAddress.a[i]; - } - pRPacket->SSap |= LLC_COMMAND_RESPONSE_BIT; - - Para.pParaPtr = pMb; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para); - } - break; - - case SK_PACKET_CHECK_TX: - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Check your tx line.\n")) - - /* A port checking us requests us to check our tx line. */ - pRPort->CheckingState |= SK_RLMT_PCS_TX; - - /* Start PortDownTx timer. */ - Para.Para32[0] = PortNumber; - Para.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pRPort->DownTxTimer, - SK_RLMT_PORTDOWN_TIM_VAL, SKGE_RLMT, - SK_RLMT_PORTDOWN_TX_TIM, Para); - - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - - if ((Para.pParaPtr = SkRlmtBuildPacket(pAC, IoC, PortNumber, - SK_PACKET_ALIVE, &pAC->Addr.Port[PortNumber].CurrentMacAddress, - &SkRlmtMcAddr)) != NULL) { - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para); - } - break; - - case SK_PACKET_ADDR_CHANGED: - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Address Change.\n")) - - /* Build the check chain. */ - SkRlmtBuildCheckChain(pAC, pRPort->Net->NetNumber); - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - break; - - default: - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Unknown RLMT packet.\n")) - - /* RA;:;: ??? */ - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - } - } - else if (pSPacket->DSap == SK_RLMT_SPT_DSAP && - pSPacket->Ctrl == SK_RLMT_SPT_CTRL && - (pSPacket->SSap & ~LLC_COMMAND_RESPONSE_BIT) == SK_RLMT_SPT_SSAP) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: BPDU Packet.\n")) - - /* Spanning Tree packet. */ - pRPort->RxSpHelloCts++; - - if (!SK_ADDR_EQUAL(&pSPacket->RootId[2], &pAC->Addr.Net[pAC->Rlmt. - Port[PortNumber].Net->NetNumber].CurrentMacAddress.a[0])) { - /* - * Check segmentation if a new root bridge is set and - * the segmentation check is not currently running. - */ - if (!SK_ADDR_EQUAL(&pSPacket->RootId[2], &pRPort->Root.Id[2]) && - (pAC->Rlmt.Port[PortNumber].Net->LinksUp > 1) && - (pAC->Rlmt.Port[PortNumber].Net->RlmtMode & SK_RLMT_CHECK_SEG) - != 0 && (pAC->Rlmt.Port[PortNumber].Net->CheckingState & - SK_RLMT_RCS_SEG) == 0) { - pAC->Rlmt.Port[PortNumber].Net->CheckingState |= - SK_RLMT_RCS_START_SEG | SK_RLMT_RCS_SEND_SEG; - } - - /* Store tree view of this port. */ - for (i = 0; i < 8; i++) { - pRPort->Root.Id[i] = pSPacket->RootId[i]; - } - pRPort->RootIdSet = SK_TRUE; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_DUMP, - ("Root ID %d: %02x %02x %02x %02x %02x %02x %02x %02x.\n", - PortNumber, - pRPort->Root.Id[0], pRPort->Root.Id[1], - pRPort->Root.Id[2], pRPort->Root.Id[3], - pRPort->Root.Id[4], pRPort->Root.Id[5], - pRPort->Root.Id[6], pRPort->Root.Id[7])) - } - - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - if ((pAC->Rlmt.Port[PortNumber].Net->CheckingState & - SK_RLMT_RCS_REPORT_SEG) != 0) { - SkRlmtCheckSeg(pAC, IoC, pAC->Rlmt.Port[PortNumber].Net->NetNumber); - } - } - else { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_RX, - ("SkRlmtPacketReceive: Unknown Packet Type.\n")) - - /* Unknown packet. */ - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - } - return; -} /* SkRlmtPacketReceive */ - - -/****************************************************************************** - * - * SkRlmtCheckPort - check if a port works - * - * Description: - * This routine checks if a port whose link is up received something - * and if it seems to transmit successfully. - * - * # PortState: PsInit, PsLinkDown, PsDown, PsGoingUp, PsUp - * # PortCheckingState (Bitfield): ChkTx, ChkRx, ChkSeg - * # RlmtCheckingState (Bitfield): ChkSeg, StartChkSeg, ReportSeg - * - * if (Rx - RxBpdu == 0) { # No rx. - * if (state == PsUp) { - * PortCheckingState |= ChkRx - * } - * if (ModeCheckSeg && (Timeout == - * TO_SHORTEN(RLMT_DEFAULT_TIMEOUT))) { - * RlmtCheckingState |= ChkSeg) - * PortCheckingState |= ChkSeg - * } - * NewTimeout = TO_SHORTEN(Timeout) - * if (NewTimeout < RLMT_MIN_TIMEOUT) { - * NewTimeout = RLMT_MIN_TIMEOUT - * PortState = PsDown - * ... - * } - * } - * else { # something was received - * # Set counter to 0 at LinkDown? - * # No - rx may be reported after LinkDown ??? - * PortCheckingState &= ~ChkRx - * NewTimeout = RLMT_DEFAULT_TIMEOUT - * if (RxAck == 0) { - * possible reasons: - * is my tx line bad? -- - * send RLMT multicast and report - * back internally? (only possible - * between ports on same adapter) - * } - * if (RxChk == 0) { - * possible reasons: - * - tx line of port set to check me - * maybe bad - * - no other port/adapter available or set - * to check me - * - adapter checking me has a longer - * timeout - * ??? anything that can be done here? - * } - * } - * - * Context: - * runtime, pageable? - * - * Returns: - * New timeout value. - */ -RLMT_STATIC SK_U32 SkRlmtCheckPort( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 PortNumber) /* Port to check */ -{ - unsigned i; - SK_U32 NewTimeout; - SK_RLMT_PORT *pRPort; - SK_EVPARA Para; - - pRPort = &pAC->Rlmt.Port[PortNumber]; - - if ((pRPort->PacketsPerTimeSlot - pRPort->BpduPacketsPerTimeSlot) == 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SkRlmtCheckPort %d: No (%d) receives in last time slot.\n", - PortNumber, pRPort->PacketsPerTimeSlot)) - - /* - * Check segmentation if there was no receive at least twice - * in a row (PortNoRx is already set) and the segmentation - * check is not currently running. - */ - - if (pRPort->PortNoRx && (pAC->Rlmt.Port[PortNumber].Net->LinksUp > 1) && - (pAC->Rlmt.Port[PortNumber].Net->RlmtMode & SK_RLMT_CHECK_SEG) && - !(pAC->Rlmt.Port[PortNumber].Net->CheckingState & SK_RLMT_RCS_SEG)) { - pAC->Rlmt.Port[PortNumber].Net->CheckingState |= - SK_RLMT_RCS_START_SEG | SK_RLMT_RCS_SEND_SEG; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SkRlmtCheckPort: PortsSuspect %d, PcsRx %d.\n", - pRPort->PortsSuspect, pRPort->CheckingState & SK_RLMT_PCS_RX)) - - if (pRPort->PortState != SK_RLMT_PS_DOWN) { - NewTimeout = TO_SHORTEN(pAC->Rlmt.Port[PortNumber].Net->TimeoutValue); - if (NewTimeout < SK_RLMT_MIN_TO_VAL) { - NewTimeout = SK_RLMT_MIN_TO_VAL; - } - - if (!(pRPort->CheckingState & SK_RLMT_PCS_RX)) { - Para.Para32[0] = PortNumber; - pRPort->CheckingState |= SK_RLMT_PCS_RX; - - /* - * What shall we do if the port checked by this one receives - * our request frames? What's bad - our rx line or his tx line? - */ - Para.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pRPort->DownRxTimer, - SK_RLMT_PORTDOWN_TIM_VAL, SKGE_RLMT, - SK_RLMT_PORTDOWN_RX_TIM, Para); - - for (i = 0; i < pRPort->PortsChecked; i++) { - if (pRPort->PortCheck[i].SuspectTx) { - continue; - } - pRPort->PortCheck[i].SuspectTx = SK_TRUE; - pRPort->PortsSuspect++; - if ((Para.pParaPtr = - SkRlmtBuildPacket(pAC, IoC, PortNumber, SK_PACKET_CHECK_TX, - &pAC->Addr.Port[PortNumber].CurrentMacAddress, - &pRPort->PortCheck[i].CheckAddr)) != NULL) { - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para); - } - } - } - } - else { /* PortDown -- or all partners suspect. */ - NewTimeout = SK_RLMT_DEF_TO_VAL; - } - pRPort->PortNoRx = SK_TRUE; - } - else { /* A non-BPDU packet was received. */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SkRlmtCheckPort %d: %d (%d) receives in last time slot.\n", - PortNumber, - pRPort->PacketsPerTimeSlot - pRPort->BpduPacketsPerTimeSlot, - pRPort->PacketsPerTimeSlot)) - - SkRlmtPortReceives(pAC, IoC, PortNumber); - if (pAC->Rlmt.CheckSwitch) { - SkRlmtCheckSwitch(pAC, IoC, pRPort->Net->NetNumber); - } - - NewTimeout = SK_RLMT_DEF_TO_VAL; - } - - return (NewTimeout); -} /* SkRlmtCheckPort */ - - -/****************************************************************************** - * - * SkRlmtSelectBcRx - select new active port, criteria 1 (CLP) - * - * Description: - * This routine selects the port that received a broadcast frame - * substantially later than all other ports. - * - * Context: - * runtime, pageable? - * - * Returns: - * SK_BOOL - */ -RLMT_STATIC SK_BOOL SkRlmtSelectBcRx( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 Active, /* Active port */ -SK_U32 PrefPort, /* Preferred port */ -SK_U32 *pSelect) /* New active port */ -{ - SK_U64 BcTimeStamp; - SK_U32 i; - SK_BOOL PortFound; - - BcTimeStamp = 0; /* Not totally necessary, but feeling better. */ - PortFound = SK_FALSE; - - /* Select port with the latest TimeStamp. */ - for (i = 0; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("TimeStamp Port %d (Down: %d, NoRx: %d): %08x %08x.\n", - i, - pAC->Rlmt.Port[i].PortDown, pAC->Rlmt.Port[i].PortNoRx, - *((SK_U32*)(&pAC->Rlmt.Port[i].BcTimeStamp) + OFFS_HI32), - *((SK_U32*)(&pAC->Rlmt.Port[i].BcTimeStamp) + OFFS_LO32))) - - if (!pAC->Rlmt.Port[i].PortDown && !pAC->Rlmt.Port[i].PortNoRx) { - if (!PortFound || pAC->Rlmt.Port[i].BcTimeStamp > BcTimeStamp) { - BcTimeStamp = pAC->Rlmt.Port[i].BcTimeStamp; - *pSelect = i; - PortFound = SK_TRUE; - } - } - } - - if (PortFound) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Port %d received the last broadcast.\n", *pSelect)) - - /* Look if another port's time stamp is similar. */ - for (i = 0; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - if (i == *pSelect) { - continue; - } - if (!pAC->Rlmt.Port[i].PortDown && !pAC->Rlmt.Port[i].PortNoRx && - (pAC->Rlmt.Port[i].BcTimeStamp > - BcTimeStamp - SK_RLMT_BC_DELTA || - pAC->Rlmt.Port[i].BcTimeStamp + - SK_RLMT_BC_DELTA > BcTimeStamp)) { - PortFound = SK_FALSE; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Port %d received a broadcast at a similar time.\n", i)) - break; - } - } - } - -#ifdef DEBUG - if (PortFound) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SELECT_BCRX found Port %d receiving the substantially " - "latest broadcast (%u).\n", - *pSelect, - BcTimeStamp - pAC->Rlmt.Port[1 - *pSelect].BcTimeStamp)) - } -#endif /* DEBUG */ - - return (PortFound); -} /* SkRlmtSelectBcRx */ - - -/****************************************************************************** - * - * SkRlmtSelectNotSuspect - select new active port, criteria 2 (CLP) - * - * Description: - * This routine selects a good port (it is PortUp && !SuspectRx). - * - * Context: - * runtime, pageable? - * - * Returns: - * SK_BOOL - */ -RLMT_STATIC SK_BOOL SkRlmtSelectNotSuspect( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 Active, /* Active port */ -SK_U32 PrefPort, /* Preferred port */ -SK_U32 *pSelect) /* New active port */ -{ - SK_U32 i; - SK_BOOL PortFound; - - PortFound = SK_FALSE; - - /* Select first port that is PortUp && !SuspectRx. */ - for (i = 0; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - if (!pAC->Rlmt.Port[i].PortDown && - !(pAC->Rlmt.Port[i].CheckingState & SK_RLMT_PCS_RX)) { - *pSelect = i; - if (!pAC->Rlmt.Port[Active].PortDown && - !(pAC->Rlmt.Port[Active].CheckingState & SK_RLMT_PCS_RX)) { - *pSelect = Active; - } - if (!pAC->Rlmt.Port[PrefPort].PortDown && - !(pAC->Rlmt.Port[PrefPort].CheckingState & SK_RLMT_PCS_RX)) { - *pSelect = PrefPort; - } - PortFound = SK_TRUE; - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SELECT_NOTSUSPECT found Port %d up and not check RX.\n", - *pSelect)) - break; - } - } - return (PortFound); -} /* SkRlmtSelectNotSuspect */ - - -/****************************************************************************** - * - * SkRlmtSelectUp - select new active port, criteria 3, 4 (CLP) - * - * Description: - * This routine selects a port that is up. - * - * Context: - * runtime, pageable? - * - * Returns: - * SK_BOOL - */ -RLMT_STATIC SK_BOOL SkRlmtSelectUp( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 Active, /* Active port */ -SK_U32 PrefPort, /* Preferred port */ -SK_U32 *pSelect, /* New active port */ -SK_BOOL AutoNegDone) /* Successfully auto-negotiated? */ -{ - SK_U32 i; - SK_BOOL PortFound; - - PortFound = SK_FALSE; - - /* Select first port that is PortUp. */ - for (i = 0; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - if (pAC->Rlmt.Port[i].PortState == SK_RLMT_PS_UP && - pAC->GIni.GP[i].PAutoNegFail != AutoNegDone) { - *pSelect = i; - if (pAC->Rlmt.Port[Active].PortState == SK_RLMT_PS_UP && - pAC->GIni.GP[Active].PAutoNegFail != AutoNegDone) { - *pSelect = Active; - } - if (pAC->Rlmt.Port[PrefPort].PortState == SK_RLMT_PS_UP && - pAC->GIni.GP[PrefPort].PAutoNegFail != AutoNegDone) { - *pSelect = PrefPort; - } - PortFound = SK_TRUE; - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SELECT_UP found Port %d up.\n", *pSelect)) - break; - } - } - return (PortFound); -} /* SkRlmtSelectUp */ - - -/****************************************************************************** - * - * SkRlmtSelectGoingUp - select new active port, criteria 5, 6 (CLP) - * - * Description: - * This routine selects the port that is going up for the longest time. - * - * Context: - * runtime, pageable? - * - * Returns: - * SK_BOOL - */ -RLMT_STATIC SK_BOOL SkRlmtSelectGoingUp( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 Active, /* Active port */ -SK_U32 PrefPort, /* Preferred port */ -SK_U32 *pSelect, /* New active port */ -SK_BOOL AutoNegDone) /* Successfully auto-negotiated? */ -{ - SK_U64 GuTimeStamp; - SK_U32 i; - SK_BOOL PortFound; - - GuTimeStamp = 0; - PortFound = SK_FALSE; - - /* Select port that is PortGoingUp for the longest time. */ - for (i = 0; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - if (pAC->Rlmt.Port[i].PortState == SK_RLMT_PS_GOING_UP && - pAC->GIni.GP[i].PAutoNegFail != AutoNegDone) { - GuTimeStamp = pAC->Rlmt.Port[i].GuTimeStamp; - *pSelect = i; - PortFound = SK_TRUE; - break; - } - } - - if (!PortFound) { - return (SK_FALSE); - } - - for (i = *pSelect + 1; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - if (pAC->Rlmt.Port[i].PortState == SK_RLMT_PS_GOING_UP && - pAC->Rlmt.Port[i].GuTimeStamp < GuTimeStamp && - pAC->GIni.GP[i].PAutoNegFail != AutoNegDone) { - GuTimeStamp = pAC->Rlmt.Port[i].GuTimeStamp; - *pSelect = i; - } - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SELECT_GOINGUP found Port %d going up.\n", *pSelect)) - return (SK_TRUE); -} /* SkRlmtSelectGoingUp */ - - -/****************************************************************************** - * - * SkRlmtSelectDown - select new active port, criteria 7, 8 (CLP) - * - * Description: - * This routine selects a port that is down. - * - * Context: - * runtime, pageable? - * - * Returns: - * SK_BOOL - */ -RLMT_STATIC SK_BOOL SkRlmtSelectDown( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 Active, /* Active port */ -SK_U32 PrefPort, /* Preferred port */ -SK_U32 *pSelect, /* New active port */ -SK_BOOL AutoNegDone) /* Successfully auto-negotiated? */ -{ - SK_U32 i; - SK_BOOL PortFound; - - PortFound = SK_FALSE; - - /* Select first port that is PortDown. */ - for (i = 0; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - if (pAC->Rlmt.Port[i].PortState == SK_RLMT_PS_DOWN && - pAC->GIni.GP[i].PAutoNegFail != AutoNegDone) { - *pSelect = i; - if (pAC->Rlmt.Port[Active].PortState == SK_RLMT_PS_DOWN && - pAC->GIni.GP[Active].PAutoNegFail != AutoNegDone) { - *pSelect = Active; - } - if (pAC->Rlmt.Port[PrefPort].PortState == SK_RLMT_PS_DOWN && - pAC->GIni.GP[PrefPort].PAutoNegFail != AutoNegDone) { - *pSelect = PrefPort; - } - PortFound = SK_TRUE; - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SELECT_DOWN found Port %d down.\n", *pSelect)) - break; - } - } - return (PortFound); -} /* SkRlmtSelectDown */ - - -/****************************************************************************** - * - * SkRlmtCheckSwitch - select new active port and switch to it - * - * Description: - * This routine decides which port should be the active one and queues - * port switching if necessary. - * - * Context: - * runtime, pageable? - * - * Returns: - * Nothing. - */ -RLMT_STATIC void SkRlmtCheckSwitch( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 NetIdx) /* Net index */ -{ - SK_EVPARA Para; - SK_U32 Active; - SK_U32 PrefPort; - SK_U32 i; - SK_BOOL PortFound; - - Active = pAC->Rlmt.Net[NetIdx].ActivePort; /* Index of active port. */ - PrefPort = pAC->Rlmt.Net[NetIdx].PrefPort; /* Index of preferred port. */ - PortFound = SK_FALSE; - pAC->Rlmt.CheckSwitch = SK_FALSE; - -#if 0 /* RW 2001/10/18 - active port becomes always prefered one */ - if (pAC->Rlmt.Net[NetIdx].Preference == 0xFFFFFFFF) { /* Automatic */ - /* disable auto-fail back */ - PrefPort = Active; - } -#endif - - if (pAC->Rlmt.Net[NetIdx].LinksUp == 0) { - /* Last link went down - shut down the net. */ - pAC->Rlmt.Net[NetIdx].RlmtState = SK_RLMT_RS_NET_DOWN; - Para.Para32[0] = SK_RLMT_NET_DOWN_TEMP; - Para.Para32[1] = NetIdx; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_NET_DOWN, Para); - - Para.Para32[0] = pAC->Rlmt.Net[NetIdx]. - Port[pAC->Rlmt.Net[NetIdx].ActivePort]->PortNumber; - Para.Para32[1] = NetIdx; - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_ACTIVE_DOWN, Para); - return; - } /* pAC->Rlmt.LinksUp == 0 */ - else if (pAC->Rlmt.Net[NetIdx].LinksUp == 1 && - pAC->Rlmt.Net[NetIdx].RlmtState == SK_RLMT_RS_NET_DOWN) { - /* First link came up - get the net up. */ - pAC->Rlmt.Net[NetIdx].RlmtState = SK_RLMT_RS_NET_UP; - - /* - * If pAC->Rlmt.ActivePort != Para.Para32[0], - * the DRV switches to the port that came up. - */ - for (i = 0; i < pAC->Rlmt.Net[NetIdx].NumPorts; i++) { - if (!pAC->Rlmt.Net[NetIdx].Port[i]->LinkDown) { - if (!pAC->Rlmt.Net[NetIdx].Port[Active]->LinkDown) { - i = Active; - } - if (!pAC->Rlmt.Net[NetIdx].Port[PrefPort]->LinkDown) { - i = PrefPort; - } - PortFound = SK_TRUE; - break; - } - } - - if (PortFound) { - Para.Para32[0] = pAC->Rlmt.Net[NetIdx].Port[i]->PortNumber; - Para.Para32[1] = NetIdx; - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_ACTIVE_UP, Para); - - pAC->Rlmt.Net[NetIdx].ActivePort = i; - Para.Para32[0] = pAC->Rlmt.Net[NetIdx].Port[i]->PortNumber; - Para.Para32[1] = NetIdx; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_NET_UP, Para); - - if ((pAC->Rlmt.Net[NetIdx].RlmtMode & SK_RLMT_TRANSPARENT) == 0 && - (Para.pParaPtr = SkRlmtBuildPacket(pAC, IoC, - pAC->Rlmt.Net[NetIdx].Port[i]->PortNumber, - SK_PACKET_ANNOUNCE, &pAC->Addr.Net[NetIdx]. - CurrentMacAddress, &SkRlmtMcAddr)) != NULL) { - /* - * Send announce packet to RLMT multicast address to force - * switches to learn the new location of the logical MAC address. - */ - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para); - } - } - else { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_RLMT_E007, SKERR_RLMT_E007_MSG); - } - - return; - } /* LinksUp == 1 && RlmtState == SK_RLMT_RS_NET_DOWN */ - else { /* Cannot be reached in dual-net mode. */ - Para.Para32[0] = Active; - - /* - * Preselection: - * If RLMT Mode != CheckLinkState - * select port that received a broadcast frame substantially later - * than all other ports - * else select first port that is not SuspectRx - * else select first port that is PortUp - * else select port that is PortGoingUp for the longest time - * else select first port that is PortDown - * else stop. - * - * For the preselected port: - * If ActivePort is equal in quality, select ActivePort. - * - * If PrefPort is equal in quality, select PrefPort. - * - * If ActivePort != SelectedPort, - * If old ActivePort is LinkDown, - * SwitchHard - * else - * SwitchSoft - */ - /* check of ChgBcPrio flag added */ - if ((pAC->Rlmt.Net[0].RlmtMode != SK_RLMT_MODE_CLS) && - (!pAC->Rlmt.Net[0].ChgBcPrio)) { - - if (!PortFound) { - PortFound = SkRlmtSelectBcRx( - pAC, IoC, Active, PrefPort, &Para.Para32[1]); - } - - if (!PortFound) { - PortFound = SkRlmtSelectNotSuspect( - pAC, IoC, Active, PrefPort, &Para.Para32[1]); - } - } /* pAC->Rlmt.RlmtMode != SK_RLMT_MODE_CLS */ - - /* with changed priority for last broadcast received */ - if ((pAC->Rlmt.Net[0].RlmtMode != SK_RLMT_MODE_CLS) && - (pAC->Rlmt.Net[0].ChgBcPrio)) { - if (!PortFound) { - PortFound = SkRlmtSelectNotSuspect( - pAC, IoC, Active, PrefPort, &Para.Para32[1]); - } - - if (!PortFound) { - PortFound = SkRlmtSelectBcRx( - pAC, IoC, Active, PrefPort, &Para.Para32[1]); - } - } /* pAC->Rlmt.RlmtMode != SK_RLMT_MODE_CLS */ - - if (!PortFound) { - PortFound = SkRlmtSelectUp( - pAC, IoC, Active, PrefPort, &Para.Para32[1], AUTONEG_SUCCESS); - } - - if (!PortFound) { - PortFound = SkRlmtSelectUp( - pAC, IoC, Active, PrefPort, &Para.Para32[1], AUTONEG_FAILED); - } - - if (!PortFound) { - PortFound = SkRlmtSelectGoingUp( - pAC, IoC, Active, PrefPort, &Para.Para32[1], AUTONEG_SUCCESS); - } - - if (!PortFound) { - PortFound = SkRlmtSelectGoingUp( - pAC, IoC, Active, PrefPort, &Para.Para32[1], AUTONEG_FAILED); - } - - if (pAC->Rlmt.Net[0].RlmtMode != SK_RLMT_MODE_CLS) { - if (!PortFound) { - PortFound = SkRlmtSelectDown(pAC, IoC, - Active, PrefPort, &Para.Para32[1], AUTONEG_SUCCESS); - } - - if (!PortFound) { - PortFound = SkRlmtSelectDown(pAC, IoC, - Active, PrefPort, &Para.Para32[1], AUTONEG_FAILED); - } - } /* pAC->Rlmt.RlmtMode != SK_RLMT_MODE_CLS */ - - if (PortFound) { - - if (Para.Para32[1] != Active) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Active: %d, Para1: %d.\n", Active, Para.Para32[1])) - pAC->Rlmt.Net[NetIdx].ActivePort = Para.Para32[1]; - Para.Para32[0] = pAC->Rlmt.Net[NetIdx]. - Port[Para.Para32[0]]->PortNumber; - Para.Para32[1] = pAC->Rlmt.Net[NetIdx]. - Port[Para.Para32[1]]->PortNumber; - SK_HWAC_LINK_LED(pAC, IoC, Para.Para32[1], SK_LED_ACTIVE); - if (pAC->Rlmt.Port[Active].LinkDown) { - SkEventQueue(pAC, SKGE_DRV, SK_DRV_SWITCH_HARD, Para); - } - else { - SK_HWAC_LINK_LED(pAC, IoC, Para.Para32[0], SK_LED_STANDBY); - SkEventQueue(pAC, SKGE_DRV, SK_DRV_SWITCH_SOFT, Para); - } - Para.Para32[1] = NetIdx; - Para.Para32[0] = - pAC->Rlmt.Net[NetIdx].Port[Para.Para32[0]]->PortNumber; - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_ACTIVE_DOWN, Para); - Para.Para32[0] = pAC->Rlmt.Net[NetIdx]. - Port[pAC->Rlmt.Net[NetIdx].ActivePort]->PortNumber; - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_ACTIVE_UP, Para); - if ((pAC->Rlmt.Net[NetIdx].RlmtMode & SK_RLMT_TRANSPARENT) == 0 && - (Para.pParaPtr = SkRlmtBuildPacket(pAC, IoC, Para.Para32[0], - SK_PACKET_ANNOUNCE, &pAC->Addr.Net[NetIdx].CurrentMacAddress, - &SkRlmtMcAddr)) != NULL) { - /* - * Send announce packet to RLMT multicast address to force - * switches to learn the new location of the logical - * MAC address. - */ - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para); - } /* (Para.pParaPtr = SkRlmtBuildPacket(...)) != NULL */ - } /* Para.Para32[1] != Active */ - } /* PortFound */ - else { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_RLMT_E004, SKERR_RLMT_E004_MSG); - } - } /* LinksUp > 1 || LinksUp == 1 && RlmtState != SK_RLMT_RS_NET_DOWN */ - return; -} /* SkRlmtCheckSwitch */ - - -/****************************************************************************** - * - * SkRlmtCheckSeg - Report if segmentation is detected - * - * Description: - * This routine checks if the ports see different root bridges and reports - * segmentation in such a case. - * - * Context: - * runtime, pageable? - * - * Returns: - * Nothing. - */ -RLMT_STATIC void SkRlmtCheckSeg( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 NetIdx) /* Net number */ -{ - SK_EVPARA Para; - SK_RLMT_NET *pNet; - SK_U32 i, j; - SK_BOOL Equal; - - pNet = &pAC->Rlmt.Net[NetIdx]; - pNet->RootIdSet = SK_FALSE; - Equal = SK_TRUE; - - for (i = 0; i < pNet->NumPorts; i++) { - if (pNet->Port[i]->LinkDown || !pNet->Port[i]->RootIdSet) { - continue; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_DUMP, - ("Root ID %d: %02x %02x %02x %02x %02x %02x %02x %02x.\n", i, - pNet->Port[i]->Root.Id[0], pNet->Port[i]->Root.Id[1], - pNet->Port[i]->Root.Id[2], pNet->Port[i]->Root.Id[3], - pNet->Port[i]->Root.Id[4], pNet->Port[i]->Root.Id[5], - pNet->Port[i]->Root.Id[6], pNet->Port[i]->Root.Id[7])) - - if (!pNet->RootIdSet) { - pNet->Root = pNet->Port[i]->Root; - pNet->RootIdSet = SK_TRUE; - continue; - } - - for (j = 0; j < 8; j ++) { - Equal &= pNet->Port[i]->Root.Id[j] == pNet->Root.Id[j]; - if (!Equal) { - break; - } - } - - if (!Equal) { - SK_ERR_LOG(pAC, SK_ERRCL_COMM, SKERR_RLMT_E005, SKERR_RLMT_E005_MSG); - Para.Para32[0] = NetIdx; - Para.Para32[1] = (SK_U32)-1; - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_SEGMENTATION, Para); - - pNet->CheckingState &= ~SK_RLMT_RCS_REPORT_SEG; - - /* 2000-03-06 RA: New. */ - Para.Para32[0] = NetIdx; - Para.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pNet->SegTimer, SK_RLMT_SEG_TO_VAL, - SKGE_RLMT, SK_RLMT_SEG_TIM, Para); - break; - } - } /* for (i = 0; i < pNet->NumPorts; i++) */ - - /* 2000-03-06 RA: Moved here. */ - /* Segmentation check not running anymore. */ - pNet->CheckingState &= ~SK_RLMT_RCS_SEG; - -} /* SkRlmtCheckSeg */ - - -/****************************************************************************** - * - * SkRlmtPortStart - initialize port variables and start port - * - * Description: - * This routine initializes a port's variables and issues a PORT_START - * to the HWAC module. This handles retries if the start fails or the - * link eventually goes down. - * - * Context: - * runtime, pageable? - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtPortStart( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 PortNumber) /* Port number */ -{ - SK_EVPARA Para; - - pAC->Rlmt.Port[PortNumber].PortState = SK_RLMT_PS_LINK_DOWN; - pAC->Rlmt.Port[PortNumber].PortStarted = SK_TRUE; - pAC->Rlmt.Port[PortNumber].LinkDown = SK_TRUE; - pAC->Rlmt.Port[PortNumber].PortDown = SK_TRUE; - pAC->Rlmt.Port[PortNumber].CheckingState = 0; - pAC->Rlmt.Port[PortNumber].RootIdSet = SK_FALSE; - Para.Para32[0] = PortNumber; - Para.Para32[1] = (SK_U32)-1; - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_START, Para); -} /* SkRlmtPortStart */ - - -/****************************************************************************** - * - * SkRlmtEvtPortStartTim - PORT_START_TIM - * - * Description: - * This routine handles PORT_START_TIM events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtPortStartTim( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 PortNumber; SK_U32 -1 */ -{ - SK_U32 i; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTSTART_TIMEOUT Port %d Event BEGIN.\n", Para.Para32[0])) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTSTART_TIMEOUT Event EMPTY.\n")) - return; - } - - /* - * Used to start non-preferred ports if the preferred one - * does not come up. - * This timeout needs only be set when starting the first - * (preferred) port. - */ - if (pAC->Rlmt.Port[Para.Para32[0]].LinkDown) { - /* PORT_START failed. */ - for (i = 0; i < pAC->Rlmt.Port[Para.Para32[0]].Net->NumPorts; i++) { - if (!pAC->Rlmt.Port[Para.Para32[0]].Net->Port[i]->PortStarted) { - SkRlmtPortStart(pAC, IoC, - pAC->Rlmt.Port[Para.Para32[0]].Net->Port[i]->PortNumber); - } - } - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTSTART_TIMEOUT Event END.\n")) -} /* SkRlmtEvtPortStartTim */ - - -/****************************************************************************** - * - * SkRlmtEvtLinkUp - LINK_UP - * - * Description: - * This routine handles LLINK_UP events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtLinkUp( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 PortNumber; SK_U32 Undefined */ -{ - SK_U32 i; - SK_RLMT_PORT *pRPort; - SK_EVPARA Para2; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_LINK_UP Port %d Event BEGIN.\n", Para.Para32[0])) - - pRPort = &pAC->Rlmt.Port[Para.Para32[0]]; - if (!pRPort->PortStarted) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_RLMT_E008, SKERR_RLMT_E008_MSG); - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_LINK_UP Event EMPTY.\n")) - return; - } - - if (!pRPort->LinkDown) { - /* RA;:;: Any better solution? */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_LINK_UP Event EMPTY.\n")) - return; - } - - SkTimerStop(pAC, IoC, &pRPort->UpTimer); - SkTimerStop(pAC, IoC, &pRPort->DownRxTimer); - SkTimerStop(pAC, IoC, &pRPort->DownTxTimer); - - /* Do something if timer already fired? */ - - pRPort->LinkDown = SK_FALSE; - pRPort->PortState = SK_RLMT_PS_GOING_UP; - pRPort->GuTimeStamp = SkOsGetTime(pAC); - pRPort->BcTimeStamp = 0; - pRPort->Net->LinksUp++; - if (pRPort->Net->LinksUp == 1) { - SK_HWAC_LINK_LED(pAC, IoC, Para.Para32[0], SK_LED_ACTIVE); - } - else { - SK_HWAC_LINK_LED(pAC, IoC, Para.Para32[0], SK_LED_STANDBY); - } - - for (i = 0; i < pRPort->Net->NumPorts; i++) { - if (!pRPort->Net->Port[i]->PortStarted) { - SkRlmtPortStart(pAC, IoC, pRPort->Net->Port[i]->PortNumber); - } - } - - SkRlmtCheckSwitch(pAC, IoC, pRPort->Net->NetNumber); - - if (pRPort->Net->LinksUp >= 2) { - if (pRPort->Net->RlmtMode & SK_RLMT_CHECK_LOC_LINK) { - /* Build the check chain. */ - SkRlmtBuildCheckChain(pAC, pRPort->Net->NetNumber); - } - } - - /* If the first link comes up, start the periodical RLMT timeout. */ - if (pRPort->Net->NumPorts > 1 && pRPort->Net->LinksUp == 1 && - (pRPort->Net->RlmtMode & SK_RLMT_CHECK_OTHERS) != 0) { - Para2.Para32[0] = pRPort->Net->NetNumber; - Para2.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pRPort->Net->LocTimer, - pRPort->Net->TimeoutValue, SKGE_RLMT, SK_RLMT_TIM, Para2); - } - - Para2 = Para; - Para2.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pRPort->UpTimer, SK_RLMT_PORTUP_TIM_VAL, - SKGE_RLMT, SK_RLMT_PORTUP_TIM, Para2); - - /* Later: if (pAC->Rlmt.RlmtMode & SK_RLMT_CHECK_LOC_LINK) && */ - if ((pRPort->Net->RlmtMode & SK_RLMT_TRANSPARENT) == 0 && - (pRPort->Net->RlmtMode & SK_RLMT_CHECK_LINK) != 0 && - (Para2.pParaPtr = - SkRlmtBuildPacket(pAC, IoC, Para.Para32[0], SK_PACKET_ANNOUNCE, - &pAC->Addr.Port[Para.Para32[0]].CurrentMacAddress, &SkRlmtMcAddr) - ) != NULL) { - /* Send "new" packet to RLMT multicast address. */ - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para2); - } - - if (pRPort->Net->RlmtMode & SK_RLMT_CHECK_SEG) { - if ((Para2.pParaPtr = - SkRlmtBuildSpanningTreePacket(pAC, IoC, Para.Para32[0])) != NULL) { - pAC->Rlmt.Port[Para.Para32[0]].RootIdSet = SK_FALSE; - pRPort->Net->CheckingState |= - SK_RLMT_RCS_SEG | SK_RLMT_RCS_REPORT_SEG; - - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para2); - - Para.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pRPort->Net->SegTimer, - SK_RLMT_SEG_TO_VAL, SKGE_RLMT, SK_RLMT_SEG_TIM, Para); - } - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_LINK_UP Event END.\n")) -} /* SkRlmtEvtLinkUp */ - - -/****************************************************************************** - * - * SkRlmtEvtPortUpTim - PORT_UP_TIM - * - * Description: - * This routine handles PORT_UP_TIM events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtPortUpTim( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 PortNumber; SK_U32 -1 */ -{ - SK_RLMT_PORT *pRPort; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTUP_TIM Port %d Event BEGIN.\n", Para.Para32[0])) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTUP_TIM Event EMPTY.\n")) - return; - } - - pRPort = &pAC->Rlmt.Port[Para.Para32[0]]; - if (pRPort->LinkDown || (pRPort->PortState == SK_RLMT_PS_UP)) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTUP_TIM Port %d Event EMPTY.\n", Para.Para32[0])) - return; - } - - pRPort->PortDown = SK_FALSE; - pRPort->PortState = SK_RLMT_PS_UP; - pRPort->Net->PortsUp++; - if (pRPort->Net->RlmtState != SK_RLMT_RS_INIT) { - if (pAC->Rlmt.NumNets <= 1) { - SkRlmtCheckSwitch(pAC, IoC, pRPort->Net->NetNumber); - } - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_PORT_UP, Para); - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTUP_TIM Event END.\n")) -} /* SkRlmtEvtPortUpTim */ - - -/****************************************************************************** - * - * SkRlmtEvtPortDownTim - PORT_DOWN_* - * - * Description: - * This routine handles PORT_DOWN_* events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtPortDownX( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 Event, /* Event code */ -SK_EVPARA Para) /* SK_U32 PortNumber; SK_U32 -1 */ -{ - SK_RLMT_PORT *pRPort; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTDOWN* Port %d Event (%d) BEGIN.\n", - Para.Para32[0], Event)) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTDOWN* Event EMPTY.\n")) - return; - } - - pRPort = &pAC->Rlmt.Port[Para.Para32[0]]; - if (!pRPort->PortStarted || (Event == SK_RLMT_PORTDOWN_TX_TIM && - !(pRPort->CheckingState & SK_RLMT_PCS_TX))) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTDOWN* Event (%d) EMPTY.\n", Event)) - return; - } - - /* Stop port's timers. */ - SkTimerStop(pAC, IoC, &pRPort->UpTimer); - SkTimerStop(pAC, IoC, &pRPort->DownRxTimer); - SkTimerStop(pAC, IoC, &pRPort->DownTxTimer); - - if (pRPort->PortState != SK_RLMT_PS_LINK_DOWN) { - pRPort->PortState = SK_RLMT_PS_DOWN; - } - - if (!pRPort->PortDown) { - pRPort->Net->PortsUp--; - pRPort->PortDown = SK_TRUE; - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_PORT_DOWN, Para); - } - - pRPort->PacketsPerTimeSlot = 0; - /* pRPort->DataPacketsPerTimeSlot = 0; */ - pRPort->BpduPacketsPerTimeSlot = 0; - pRPort->BcTimeStamp = 0; - - /* - * RA;:;: To be checked: - * - actions at RLMT_STOP: We should not switch anymore. - */ - if (pRPort->Net->RlmtState != SK_RLMT_RS_INIT) { - if (Para.Para32[0] == - pRPort->Net->Port[pRPort->Net->ActivePort]->PortNumber) { - /* Active Port went down. */ - SkRlmtCheckSwitch(pAC, IoC, pRPort->Net->NetNumber); - } - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORTDOWN* Event (%d) END.\n", Event)) -} /* SkRlmtEvtPortDownX */ - - -/****************************************************************************** - * - * SkRlmtEvtLinkDown - LINK_DOWN - * - * Description: - * This routine handles LINK_DOWN events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtLinkDown( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 PortNumber; SK_U32 Undefined */ -{ - SK_RLMT_PORT *pRPort; - - pRPort = &pAC->Rlmt.Port[Para.Para32[0]]; - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_LINK_DOWN Port %d Event BEGIN.\n", Para.Para32[0])) - - if (!pAC->Rlmt.Port[Para.Para32[0]].LinkDown) { - pRPort->Net->LinksUp--; - pRPort->LinkDown = SK_TRUE; - pRPort->PortState = SK_RLMT_PS_LINK_DOWN; - SK_HWAC_LINK_LED(pAC, IoC, Para.Para32[0], SK_LED_OFF); - - if ((pRPort->Net->RlmtMode & SK_RLMT_CHECK_LOC_LINK) != 0) { - /* Build the check chain. */ - SkRlmtBuildCheckChain(pAC, pRPort->Net->NetNumber); - } - - /* Ensure that port is marked down. */ - Para.Para32[1] = -1; - (void)SkRlmtEvent(pAC, IoC, SK_RLMT_PORTDOWN, Para); - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_LINK_DOWN Event END.\n")) -} /* SkRlmtEvtLinkDown */ - - -/****************************************************************************** - * - * SkRlmtEvtPortAddr - PORT_ADDR - * - * Description: - * This routine handles PORT_ADDR events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtPortAddr( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 PortNumber; SK_U32 -1 */ -{ - SK_U32 i, j; - SK_RLMT_PORT *pRPort; - SK_MAC_ADDR *pOldMacAddr; - SK_MAC_ADDR *pNewMacAddr; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORT_ADDR Port %d Event BEGIN.\n", Para.Para32[0])) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORT_ADDR Event EMPTY.\n")) - return; - } - - /* Port's physical MAC address changed. */ - pOldMacAddr = &pAC->Addr.Port[Para.Para32[0]].PreviousMacAddress; - pNewMacAddr = &pAC->Addr.Port[Para.Para32[0]].CurrentMacAddress; - - /* - * NOTE: This is not scalable for solutions where ports are - * checked remotely. There, we need to send an RLMT - * address change packet - and how do we ensure delivery? - */ - for (i = 0; i < (SK_U32)pAC->GIni.GIMacsFound; i++) { - pRPort = &pAC->Rlmt.Port[i]; - for (j = 0; j < pRPort->PortsChecked; j++) { - if (SK_ADDR_EQUAL( - pRPort->PortCheck[j].CheckAddr.a, pOldMacAddr->a)) { - pRPort->PortCheck[j].CheckAddr = *pNewMacAddr; - } - } - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PORT_ADDR Event END.\n")) -} /* SkRlmtEvtPortAddr */ - - -/****************************************************************************** - * - * SkRlmtEvtStart - START - * - * Description: - * This routine handles START events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtStart( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 NetNumber; SK_U32 -1 */ -{ - SK_EVPARA Para2; - SK_U32 PortIdx; - SK_U32 PortNumber; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_START Net %d Event BEGIN.\n", Para.Para32[0])) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_START Event EMPTY.\n")) - return; - } - - if (Para.Para32[0] >= pAC->Rlmt.NumNets) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad NetNumber %d.\n", Para.Para32[0])) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_START Event EMPTY.\n")) - return; - } - - if (pAC->Rlmt.Net[Para.Para32[0]].RlmtState != SK_RLMT_RS_INIT) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_START Event EMPTY.\n")) - return; - } - - if (pAC->Rlmt.NetsStarted >= pAC->Rlmt.NumNets) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("All nets should have been started.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_START Event EMPTY.\n")) - return; - } - - if (pAC->Rlmt.Net[Para.Para32[0]].PrefPort >= - pAC->Rlmt.Net[Para.Para32[0]].NumPorts) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_RLMT_E009, SKERR_RLMT_E009_MSG); - - /* Change PrefPort to internal default. */ - Para2.Para32[0] = 0xFFFFFFFF; - Para2.Para32[1] = Para.Para32[0]; - (void)SkRlmtEvent(pAC, IoC, SK_RLMT_PREFPORT_CHANGE, Para2); - } - - PortIdx = pAC->Rlmt.Net[Para.Para32[0]].PrefPort; - PortNumber = pAC->Rlmt.Net[Para.Para32[0]].Port[PortIdx]->PortNumber; - - pAC->Rlmt.Net[Para.Para32[0]].LinksUp = 0; - pAC->Rlmt.Net[Para.Para32[0]].PortsUp = 0; - pAC->Rlmt.Net[Para.Para32[0]].CheckingState = 0; - pAC->Rlmt.Net[Para.Para32[0]].RlmtState = SK_RLMT_RS_NET_DOWN; - - /* Start preferred port. */ - SkRlmtPortStart(pAC, IoC, PortNumber); - - /* Start Timer (for first port only). */ - Para2.Para32[0] = PortNumber; - Para2.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pAC->Rlmt.Port[PortNumber].UpTimer, - SK_RLMT_PORTSTART_TIM_VAL, SKGE_RLMT, SK_RLMT_PORTSTART_TIM, Para2); - - pAC->Rlmt.NetsStarted++; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_START Event END.\n")) -} /* SkRlmtEvtStart */ - - -/****************************************************************************** - * - * SkRlmtEvtStop - STOP - * - * Description: - * This routine handles STOP events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtStop( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 NetNumber; SK_U32 -1 */ -{ - SK_EVPARA Para2; - SK_U32 PortNumber; - SK_U32 i; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STOP Net %d Event BEGIN.\n", Para.Para32[0])) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STOP Event EMPTY.\n")) - return; - } - - if (Para.Para32[0] >= pAC->Rlmt.NumNets) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad NetNumber %d.\n", Para.Para32[0])) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STOP Event EMPTY.\n")) - return; - } - - if (pAC->Rlmt.Net[Para.Para32[0]].RlmtState == SK_RLMT_RS_INIT) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STOP Event EMPTY.\n")) - return; - } - - if (pAC->Rlmt.NetsStarted == 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("All nets are stopped.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STOP Event EMPTY.\n")) - return; - } - - /* Stop RLMT timers. */ - SkTimerStop(pAC, IoC, &pAC->Rlmt.Net[Para.Para32[0]].LocTimer); - SkTimerStop(pAC, IoC, &pAC->Rlmt.Net[Para.Para32[0]].SegTimer); - - /* Stop net. */ - pAC->Rlmt.Net[Para.Para32[0]].RlmtState = SK_RLMT_RS_INIT; - pAC->Rlmt.Net[Para.Para32[0]].RootIdSet = SK_FALSE; - Para2.Para32[0] = SK_RLMT_NET_DOWN_FINAL; - Para2.Para32[1] = Para.Para32[0]; /* Net# */ - SkEventQueue(pAC, SKGE_DRV, SK_DRV_NET_DOWN, Para2); - - /* Stop ports. */ - for (i = 0; i < pAC->Rlmt.Net[Para.Para32[0]].NumPorts; i++) { - PortNumber = pAC->Rlmt.Net[Para.Para32[0]].Port[i]->PortNumber; - if (pAC->Rlmt.Port[PortNumber].PortState != SK_RLMT_PS_INIT) { - SkTimerStop(pAC, IoC, &pAC->Rlmt.Port[PortNumber].UpTimer); - SkTimerStop(pAC, IoC, &pAC->Rlmt.Port[PortNumber].DownRxTimer); - SkTimerStop(pAC, IoC, &pAC->Rlmt.Port[PortNumber].DownTxTimer); - - pAC->Rlmt.Port[PortNumber].PortState = SK_RLMT_PS_INIT; - pAC->Rlmt.Port[PortNumber].RootIdSet = SK_FALSE; - pAC->Rlmt.Port[PortNumber].PortStarted = SK_FALSE; - Para2.Para32[0] = PortNumber; - Para2.Para32[1] = (SK_U32)-1; - SkEventQueue(pAC, SKGE_HWAC, SK_HWEV_PORT_STOP, Para2); - } - } - - pAC->Rlmt.NetsStarted--; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STOP Event END.\n")) -} /* SkRlmtEvtStop */ - - -/****************************************************************************** - * - * SkRlmtEvtTim - TIM - * - * Description: - * This routine handles TIM events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtTim( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 NetNumber; SK_U32 -1 */ -{ - SK_RLMT_PORT *pRPort; - SK_U32 Timeout; - SK_U32 NewTimeout; - SK_U32 PortNumber; - SK_U32 i; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_TIM Event BEGIN.\n")) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_TIM Event EMPTY.\n")) - return; - } - - if ((pAC->Rlmt.Net[Para.Para32[0]].RlmtMode & SK_RLMT_CHECK_OTHERS) == 0 || - pAC->Rlmt.Net[Para.Para32[0]].LinksUp == 0) { - /* Mode changed or all links down: No more link checking. */ - return; - } - -#if 0 - pAC->Rlmt.SwitchCheckCounter--; - if (pAC->Rlmt.SwitchCheckCounter == 0) { - pAC->Rlmt.SwitchCheckCounter; - } -#endif /* 0 */ - - NewTimeout = SK_RLMT_DEF_TO_VAL; - for (i = 0; i < pAC->Rlmt.Net[Para.Para32[0]].NumPorts; i++) { - PortNumber = pAC->Rlmt.Net[Para.Para32[0]].Port[i]->PortNumber; - pRPort = &pAC->Rlmt.Port[PortNumber]; - if (!pRPort->LinkDown) { - Timeout = SkRlmtCheckPort(pAC, IoC, PortNumber); - if (Timeout < NewTimeout) { - NewTimeout = Timeout; - } - - /* - * These counters should be set to 0 for all ports before the - * first frame is sent in the next loop. - */ - pRPort->PacketsPerTimeSlot = 0; - /* pRPort->DataPacketsPerTimeSlot = 0; */ - pRPort->BpduPacketsPerTimeSlot = 0; - } - } - pAC->Rlmt.Net[Para.Para32[0]].TimeoutValue = NewTimeout; - - if (pAC->Rlmt.Net[Para.Para32[0]].LinksUp > 1) { - /* - * If checking remote ports, also send packets if - * (LinksUp == 1) && - * this port checks at least one (remote) port. - */ - - /* - * Must be new loop, as SkRlmtCheckPort can request to - * check segmentation when e.g. checking the last port. - */ - for (i = 0; i < pAC->Rlmt.Net[Para.Para32[0]].NumPorts; i++) { - if (!pAC->Rlmt.Net[Para.Para32[0]].Port[i]->LinkDown) { - SkRlmtSend(pAC, IoC, - pAC->Rlmt.Net[Para.Para32[0]].Port[i]->PortNumber); - } - } - } - - SkTimerStart(pAC, IoC, &pAC->Rlmt.Net[Para.Para32[0]].LocTimer, - pAC->Rlmt.Net[Para.Para32[0]].TimeoutValue, SKGE_RLMT, SK_RLMT_TIM, - Para); - - if (pAC->Rlmt.Net[Para.Para32[0]].LinksUp > 1 && - (pAC->Rlmt.Net[Para.Para32[0]].RlmtMode & SK_RLMT_CHECK_SEG) && - (pAC->Rlmt.Net[Para.Para32[0]].CheckingState & SK_RLMT_RCS_START_SEG)) { - SkTimerStart(pAC, IoC, &pAC->Rlmt.Net[Para.Para32[0]].SegTimer, - SK_RLMT_SEG_TO_VAL, SKGE_RLMT, SK_RLMT_SEG_TIM, Para); - pAC->Rlmt.Net[Para.Para32[0]].CheckingState &= ~SK_RLMT_RCS_START_SEG; - pAC->Rlmt.Net[Para.Para32[0]].CheckingState |= - SK_RLMT_RCS_SEG | SK_RLMT_RCS_REPORT_SEG; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_TIM Event END.\n")) -} /* SkRlmtEvtTim */ - - -/****************************************************************************** - * - * SkRlmtEvtSegTim - SEG_TIM - * - * Description: - * This routine handles SEG_TIM events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtSegTim( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 NetNumber; SK_U32 -1 */ -{ -#ifdef xDEBUG - int j; -#endif /* DEBUG */ - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SEG_TIM Event BEGIN.\n")) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SEG_TIM Event EMPTY.\n")) - return; - } - -#ifdef xDEBUG - for (j = 0; j < pAC->Rlmt.Net[Para.Para32[0]].NumPorts; j++) { - SK_ADDR_PORT *pAPort; - SK_U32 k; - SK_U16 *InAddr; - SK_U8 InAddr8[6]; - - InAddr = (SK_U16 *)&InAddr8[0]; - pAPort = pAC->Rlmt.Net[Para.Para32[0]].Port[j]->AddrPort; - for (k = 0; k < pAPort->NextExactMatchRlmt; k++) { - /* Get exact match address k from port j. */ - XM_INADDR(IoC, pAC->Rlmt.Net[Para.Para32[0]].Port[j]->PortNumber, - XM_EXM(k), InAddr); - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("MC address %d on Port %u: %02x %02x %02x %02x %02x %02x -- %02x %02x %02x %02x %02x %02x.\n", - k, pAC->Rlmt.Net[Para.Para32[0]].Port[j]->PortNumber, - InAddr8[0], InAddr8[1], InAddr8[2], - InAddr8[3], InAddr8[4], InAddr8[5], - pAPort->Exact[k].a[0], pAPort->Exact[k].a[1], - pAPort->Exact[k].a[2], pAPort->Exact[k].a[3], - pAPort->Exact[k].a[4], pAPort->Exact[k].a[5])) - } - } -#endif /* xDEBUG */ - - SkRlmtCheckSeg(pAC, IoC, Para.Para32[0]); - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SEG_TIM Event END.\n")) -} /* SkRlmtEvtSegTim */ - - -/****************************************************************************** - * - * SkRlmtEvtPacketRx - PACKET_RECEIVED - * - * Description: - * This routine handles PACKET_RECEIVED events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtPacketRx( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_MBUF *pMb */ -{ - SK_MBUF *pMb; - SK_MBUF *pNextMb; - SK_U32 NetNumber; - - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PACKET_RECEIVED Event BEGIN.\n")) - - /* Should we ignore frames during port switching? */ - -#ifdef DEBUG - pMb = Para.pParaPtr; - if (pMb == NULL) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, ("No mbuf.\n")) - } - else if (pMb->pNext != NULL) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("More than one mbuf or pMb->pNext not set.\n")) - } -#endif /* DEBUG */ - - for (pMb = Para.pParaPtr; pMb != NULL; pMb = pNextMb) { - pNextMb = pMb->pNext; - pMb->pNext = NULL; - - NetNumber = pAC->Rlmt.Port[pMb->PortIdx].Net->NetNumber; - if (pAC->Rlmt.Net[NetNumber].RlmtState == SK_RLMT_RS_INIT) { - SkDrvFreeRlmtMbuf(pAC, IoC, pMb); - } - else { - SkRlmtPacketReceive(pAC, IoC, pMb); - } - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PACKET_RECEIVED Event END.\n")) -} /* SkRlmtEvtPacketRx */ - - -/****************************************************************************** - * - * SkRlmtEvtStatsClear - STATS_CLEAR - * - * Description: - * This routine handles STATS_CLEAR events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtStatsClear( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 NetNumber; SK_U32 -1 */ -{ - SK_U32 i; - SK_RLMT_PORT *pRPort; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STATS_CLEAR Event BEGIN.\n")) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STATS_CLEAR Event EMPTY.\n")) - return; - } - - if (Para.Para32[0] >= pAC->Rlmt.NumNets) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad NetNumber %d.\n", Para.Para32[0])) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STATS_CLEAR Event EMPTY.\n")) - return; - } - - /* Clear statistics for logical and physical ports. */ - for (i = 0; i < pAC->Rlmt.Net[Para.Para32[0]].NumPorts; i++) { - pRPort = - &pAC->Rlmt.Port[pAC->Rlmt.Net[Para.Para32[0]].Port[i]->PortNumber]; - pRPort->TxHelloCts = 0; - pRPort->RxHelloCts = 0; - pRPort->TxSpHelloReqCts = 0; - pRPort->RxSpHelloCts = 0; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STATS_CLEAR Event END.\n")) -} /* SkRlmtEvtStatsClear */ - - -/****************************************************************************** - * - * SkRlmtEvtStatsUpdate - STATS_UPDATE - * - * Description: - * This routine handles STATS_UPDATE events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtStatsUpdate( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 NetNumber; SK_U32 -1 */ -{ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STATS_UPDATE Event BEGIN.\n")) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STATS_UPDATE Event EMPTY.\n")) - return; - } - - if (Para.Para32[0] >= pAC->Rlmt.NumNets) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad NetNumber %d.\n", Para.Para32[0])) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STATS_UPDATE Event EMPTY.\n")) - return; - } - - /* Update statistics - currently always up-to-date. */ - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_STATS_UPDATE Event END.\n")) -} /* SkRlmtEvtStatsUpdate */ - - -/****************************************************************************** - * - * SkRlmtEvtPrefportChange - PREFPORT_CHANGE - * - * Description: - * This routine handles PREFPORT_CHANGE events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtPrefportChange( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 PortIndex; SK_U32 NetNumber */ -{ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PREFPORT_CHANGE to Port %d Event BEGIN.\n", Para.Para32[0])) - - if (Para.Para32[1] >= pAC->Rlmt.NumNets) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad NetNumber %d.\n", Para.Para32[1])) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PREFPORT_CHANGE Event EMPTY.\n")) - return; - } - - /* 0xFFFFFFFF == auto-mode. */ - if (Para.Para32[0] == 0xFFFFFFFF) { - pAC->Rlmt.Net[Para.Para32[1]].PrefPort = SK_RLMT_DEF_PREF_PORT; - } - else { - if (Para.Para32[0] >= pAC->Rlmt.Net[Para.Para32[1]].NumPorts) { - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_RLMT_E010, SKERR_RLMT_E010_MSG); - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PREFPORT_CHANGE Event EMPTY.\n")) - return; - } - - pAC->Rlmt.Net[Para.Para32[1]].PrefPort = Para.Para32[0]; - } - - pAC->Rlmt.Net[Para.Para32[1]].Preference = Para.Para32[0]; - - if (pAC->Rlmt.Net[Para.Para32[1]].RlmtState != SK_RLMT_RS_INIT) { - SkRlmtCheckSwitch(pAC, IoC, Para.Para32[1]); - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_PREFPORT_CHANGE Event END.\n")) -} /* SkRlmtEvtPrefportChange */ - - -/****************************************************************************** - * - * SkRlmtEvtSetNets - SET_NETS - * - * Description: - * This routine handles SET_NETS events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtSetNets( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 NumNets; SK_U32 -1 */ -{ - int i; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SET_NETS Event BEGIN.\n")) - - if (Para.Para32[1] != (SK_U32)-1) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad Parameter.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SET_NETS Event EMPTY.\n")) - return; - } - - if (Para.Para32[0] == 0 || Para.Para32[0] > SK_MAX_NETS || - Para.Para32[0] > (SK_U32)pAC->GIni.GIMacsFound) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad number of nets: %d.\n", Para.Para32[0])) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SET_NETS Event EMPTY.\n")) - return; - } - - if (Para.Para32[0] == pAC->Rlmt.NumNets) { /* No change. */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SET_NETS Event EMPTY.\n")) - return; - } - - /* Entering and leaving dual mode only allowed while nets are stopped. */ - if (pAC->Rlmt.NetsStarted > 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Changing dual mode only allowed while all nets are stopped.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SET_NETS Event EMPTY.\n")) - return; - } - - if (Para.Para32[0] == 1) { - if (pAC->Rlmt.NumNets > 1) { - /* Clear logical MAC addr from second net's active port. */ - (void)SkAddrOverride(pAC, IoC, pAC->Rlmt.Net[1].Port[pAC->Addr. - Net[1].ActivePort]->PortNumber, NULL, SK_ADDR_CLEAR_LOGICAL); - pAC->Rlmt.Net[1].NumPorts = 0; - } - - pAC->Rlmt.NumNets = Para.Para32[0]; - for (i = 0; (SK_U32)i < pAC->Rlmt.NumNets; i++) { - pAC->Rlmt.Net[i].RlmtState = SK_RLMT_RS_INIT; - pAC->Rlmt.Net[i].RootIdSet = SK_FALSE; - pAC->Rlmt.Net[i].Preference = 0xFFFFFFFF; /* "Automatic" */ - pAC->Rlmt.Net[i].PrefPort = SK_RLMT_DEF_PREF_PORT; - /* Just assuming. */ - pAC->Rlmt.Net[i].ActivePort = pAC->Rlmt.Net[i].PrefPort; - pAC->Rlmt.Net[i].RlmtMode = SK_RLMT_DEF_MODE; - pAC->Rlmt.Net[i].TimeoutValue = SK_RLMT_DEF_TO_VAL; - pAC->Rlmt.Net[i].NetNumber = i; - } - - pAC->Rlmt.Port[1].Net= &pAC->Rlmt.Net[0]; - pAC->Rlmt.Net[0].NumPorts = pAC->GIni.GIMacsFound; - - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_SET_NETS, Para); - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("RLMT: Changed to one net with two ports.\n")) - } - else if (Para.Para32[0] == 2) { - pAC->Rlmt.Port[1].Net= &pAC->Rlmt.Net[1]; - pAC->Rlmt.Net[1].NumPorts = pAC->GIni.GIMacsFound - 1; - pAC->Rlmt.Net[0].NumPorts = - pAC->GIni.GIMacsFound - pAC->Rlmt.Net[1].NumPorts; - - pAC->Rlmt.NumNets = Para.Para32[0]; - for (i = 0; (SK_U32)i < pAC->Rlmt.NumNets; i++) { - pAC->Rlmt.Net[i].RlmtState = SK_RLMT_RS_INIT; - pAC->Rlmt.Net[i].RootIdSet = SK_FALSE; - pAC->Rlmt.Net[i].Preference = 0xFFFFFFFF; /* "Automatic" */ - pAC->Rlmt.Net[i].PrefPort = SK_RLMT_DEF_PREF_PORT; - /* Just assuming. */ - pAC->Rlmt.Net[i].ActivePort = pAC->Rlmt.Net[i].PrefPort; - pAC->Rlmt.Net[i].RlmtMode = SK_RLMT_DEF_MODE; - pAC->Rlmt.Net[i].TimeoutValue = SK_RLMT_DEF_TO_VAL; - - pAC->Rlmt.Net[i].NetNumber = i; - } - - /* Set logical MAC addr on second net's active port. */ - (void)SkAddrOverride(pAC, IoC, pAC->Rlmt.Net[1].Port[pAC->Addr. - Net[1].ActivePort]->PortNumber, NULL, SK_ADDR_SET_LOGICAL); - - SkEventQueue(pAC, SKGE_PNMI, SK_PNMI_EVT_RLMT_SET_NETS, Para); - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("RLMT: Changed to two nets with one port each.\n")) - } - else { - /* Not implemented for more than two nets. */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SetNets not implemented for more than two nets.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SET_NETS Event EMPTY.\n")) - return; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_SET_NETS Event END.\n")) -} /* SkRlmtSetNets */ - - -/****************************************************************************** - * - * SkRlmtEvtModeChange - MODE_CHANGE - * - * Description: - * This routine handles MODE_CHANGE events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * Nothing - */ -RLMT_STATIC void SkRlmtEvtModeChange( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_EVPARA Para) /* SK_U32 NewMode; SK_U32 NetNumber */ -{ - SK_EVPARA Para2; - SK_U32 i; - SK_U32 PrevRlmtMode; - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_MODE_CHANGE Event BEGIN.\n")) - - if (Para.Para32[1] >= pAC->Rlmt.NumNets) { - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Bad NetNumber %d.\n", Para.Para32[1])) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_MODE_CHANGE Event EMPTY.\n")) - return; - } - - Para.Para32[0] |= SK_RLMT_CHECK_LINK; - - if ((pAC->Rlmt.Net[Para.Para32[1]].NumPorts == 1) && - Para.Para32[0] != SK_RLMT_MODE_CLS) { - pAC->Rlmt.Net[Para.Para32[1]].RlmtMode = SK_RLMT_MODE_CLS; - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Forced RLMT mode to CLS on single port net.\n")) - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_MODE_CHANGE Event EMPTY.\n")) - return; - } - - /* Update RLMT mode. */ - PrevRlmtMode = pAC->Rlmt.Net[Para.Para32[1]].RlmtMode; - pAC->Rlmt.Net[Para.Para32[1]].RlmtMode = Para.Para32[0]; - - if ((PrevRlmtMode & SK_RLMT_CHECK_LOC_LINK) != - (pAC->Rlmt.Net[Para.Para32[1]].RlmtMode & SK_RLMT_CHECK_LOC_LINK)) { - /* SK_RLMT_CHECK_LOC_LINK bit changed. */ - if ((PrevRlmtMode & SK_RLMT_CHECK_OTHERS) == 0 && - pAC->Rlmt.Net[Para.Para32[1]].NumPorts > 1 && - pAC->Rlmt.Net[Para.Para32[1]].PortsUp >= 1) { - /* 20001207 RA: Was "PortsUp == 1". */ - Para2.Para32[0] = Para.Para32[1]; - Para2.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pAC->Rlmt.Net[Para.Para32[1]].LocTimer, - pAC->Rlmt.Net[Para.Para32[1]].TimeoutValue, - SKGE_RLMT, SK_RLMT_TIM, Para2); - } - } - - if ((PrevRlmtMode & SK_RLMT_CHECK_SEG) != - (pAC->Rlmt.Net[Para.Para32[1]].RlmtMode & SK_RLMT_CHECK_SEG)) { - /* SK_RLMT_CHECK_SEG bit changed. */ - for (i = 0; i < pAC->Rlmt.Net[Para.Para32[1]].NumPorts; i++) { - (void)SkAddrMcClear(pAC, IoC, - pAC->Rlmt.Net[Para.Para32[1]].Port[i]->PortNumber, - SK_ADDR_PERMANENT | SK_MC_SW_ONLY); - - /* Add RLMT MC address. */ - (void)SkAddrMcAdd(pAC, IoC, - pAC->Rlmt.Net[Para.Para32[1]].Port[i]->PortNumber, - &SkRlmtMcAddr, SK_ADDR_PERMANENT); - - if ((pAC->Rlmt.Net[Para.Para32[1]].RlmtMode & - SK_RLMT_CHECK_SEG) != 0) { - /* Add BPDU MC address. */ - (void)SkAddrMcAdd(pAC, IoC, - pAC->Rlmt.Net[Para.Para32[1]].Port[i]->PortNumber, - &BridgeMcAddr, SK_ADDR_PERMANENT); - - if (pAC->Rlmt.Net[Para.Para32[1]].RlmtState != SK_RLMT_RS_INIT) { - if (!pAC->Rlmt.Net[Para.Para32[1]].Port[i]->LinkDown && - (Para2.pParaPtr = SkRlmtBuildSpanningTreePacket( - pAC, IoC, i)) != NULL) { - pAC->Rlmt.Net[Para.Para32[1]].Port[i]->RootIdSet = - SK_FALSE; - SkEventQueue(pAC, SKGE_DRV, SK_DRV_RLMT_SEND, Para2); - } - } - } - (void)SkAddrMcUpdate(pAC, IoC, - pAC->Rlmt.Net[Para.Para32[1]].Port[i]->PortNumber); - } /* for ... */ - - if ((pAC->Rlmt.Net[Para.Para32[1]].RlmtMode & SK_RLMT_CHECK_SEG) != 0) { - Para2.Para32[0] = Para.Para32[1]; - Para2.Para32[1] = (SK_U32)-1; - SkTimerStart(pAC, IoC, &pAC->Rlmt.Net[Para.Para32[1]].SegTimer, - SK_RLMT_SEG_TO_VAL, SKGE_RLMT, SK_RLMT_SEG_TIM, Para2); - } - } /* SK_RLMT_CHECK_SEG bit changed. */ - - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("SK_RLMT_MODE_CHANGE Event END.\n")) -} /* SkRlmtEvtModeChange */ - - -/****************************************************************************** - * - * SkRlmtEvent - a PORT- or an RLMT-specific event happened - * - * Description: - * This routine calls subroutines to handle PORT- and RLMT-specific events. - * - * Context: - * runtime, pageable? - * may be called after SK_INIT_IO - * - * Returns: - * 0 - */ -int SkRlmtEvent( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -SK_U32 Event, /* Event code */ -SK_EVPARA Para) /* Event-specific parameter */ -{ - switch (Event) { - - /* ----- PORT events ----- */ - - case SK_RLMT_PORTSTART_TIM: /* From RLMT via TIME. */ - SkRlmtEvtPortStartTim(pAC, IoC, Para); - break; - case SK_RLMT_LINK_UP: /* From SIRQ. */ - SkRlmtEvtLinkUp(pAC, IoC, Para); - break; - case SK_RLMT_PORTUP_TIM: /* From RLMT via TIME. */ - SkRlmtEvtPortUpTim(pAC, IoC, Para); - break; - case SK_RLMT_PORTDOWN: /* From RLMT. */ - case SK_RLMT_PORTDOWN_RX_TIM: /* From RLMT via TIME. */ - case SK_RLMT_PORTDOWN_TX_TIM: /* From RLMT via TIME. */ - SkRlmtEvtPortDownX(pAC, IoC, Event, Para); - break; - case SK_RLMT_LINK_DOWN: /* From SIRQ. */ - SkRlmtEvtLinkDown(pAC, IoC, Para); - break; - case SK_RLMT_PORT_ADDR: /* From ADDR. */ - SkRlmtEvtPortAddr(pAC, IoC, Para); - break; - - /* ----- RLMT events ----- */ - - case SK_RLMT_START: /* From DRV. */ - SkRlmtEvtStart(pAC, IoC, Para); - break; - case SK_RLMT_STOP: /* From DRV. */ - SkRlmtEvtStop(pAC, IoC, Para); - break; - case SK_RLMT_TIM: /* From RLMT via TIME. */ - SkRlmtEvtTim(pAC, IoC, Para); - break; - case SK_RLMT_SEG_TIM: - SkRlmtEvtSegTim(pAC, IoC, Para); - break; - case SK_RLMT_PACKET_RECEIVED: /* From DRV. */ - SkRlmtEvtPacketRx(pAC, IoC, Para); - break; - case SK_RLMT_STATS_CLEAR: /* From PNMI. */ - SkRlmtEvtStatsClear(pAC, IoC, Para); - break; - case SK_RLMT_STATS_UPDATE: /* From PNMI. */ - SkRlmtEvtStatsUpdate(pAC, IoC, Para); - break; - case SK_RLMT_PREFPORT_CHANGE: /* From PNMI. */ - SkRlmtEvtPrefportChange(pAC, IoC, Para); - break; - case SK_RLMT_MODE_CHANGE: /* From PNMI. */ - SkRlmtEvtModeChange(pAC, IoC, Para); - break; - case SK_RLMT_SET_NETS: /* From DRV. */ - SkRlmtEvtSetNets(pAC, IoC, Para); - break; - - /* ----- Unknown events ----- */ - - default: /* Create error log entry. */ - SK_DBG_MSG(pAC, SK_DBGMOD_RLMT, SK_DBGCAT_CTRL, - ("Unknown RLMT Event %d.\n", Event)) - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_RLMT_E003, SKERR_RLMT_E003_MSG); - break; - } /* switch() */ - - return (0); -} /* SkRlmtEvent */ - -#ifdef __cplusplus -} -#endif /* __cplusplus */ diff --git a/drivers/net/sk98lin/sktimer.c b/drivers/net/sk98lin/sktimer.c deleted file mode 100644 index 4e462955ecd8..000000000000 --- a/drivers/net/sk98lin/sktimer.c +++ /dev/null @@ -1,250 +0,0 @@ -/****************************************************************************** - * - * Name: sktimer.c - * Project: Gigabit Ethernet Adapters, Event Scheduler Module - * Version: $Revision: 1.14 $ - * Date: $Date: 2003/09/16 13:46:51 $ - * Purpose: High level timer functions. - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect GmbH. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - - -/* - * Event queue and dispatcher - */ -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: sktimer.c,v 1.14 2003/09/16 13:46:51 rschmidt Exp $ (C) Marvell."; -#endif - -#include "h/skdrv1st.h" /* Driver Specific Definitions */ -#include "h/skdrv2nd.h" /* Adapter Control- and Driver specific Def. */ - -#ifdef __C2MAN__ -/* - Event queue management. - - General Description: - - */ -intro() -{} -#endif - - -/* Forward declaration */ -static void timer_done(SK_AC *pAC,SK_IOC Ioc,int Restart); - - -/* - * Inits the software timer - * - * needs to be called during Init level 1. - */ -void SkTimerInit( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc, /* IoContext */ -int Level) /* Init Level */ -{ - switch (Level) { - case SK_INIT_DATA: - pAC->Tim.StQueue = NULL; - break; - case SK_INIT_IO: - SkHwtInit(pAC, Ioc); - SkTimerDone(pAC, Ioc); - break; - default: - break; - } -} - -/* - * Stops a high level timer - * - If a timer is not in the queue the function returns normally, too. - */ -void SkTimerStop( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc, /* IoContext */ -SK_TIMER *pTimer) /* Timer Pointer to be started */ -{ - SK_TIMER **ppTimPrev; - SK_TIMER *pTm; - - /* - * remove timer from queue - */ - pTimer->TmActive = SK_FALSE; - - if (pAC->Tim.StQueue == pTimer && !pTimer->TmNext) { - SkHwtStop(pAC, Ioc); - } - - for (ppTimPrev = &pAC->Tim.StQueue; (pTm = *ppTimPrev); - ppTimPrev = &pTm->TmNext ) { - - if (pTm == pTimer) { - /* - * Timer found in queue - * - dequeue it and - * - correct delta of the next timer - */ - *ppTimPrev = pTm->TmNext; - - if (pTm->TmNext) { - /* correct delta of next timer in queue */ - pTm->TmNext->TmDelta += pTm->TmDelta; - } - return; - } - } -} - -/* - * Start a high level software timer - */ -void SkTimerStart( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc, /* IoContext */ -SK_TIMER *pTimer, /* Timer Pointer to be started */ -SK_U32 Time, /* Time value */ -SK_U32 Class, /* Event Class for this timer */ -SK_U32 Event, /* Event Value for this timer */ -SK_EVPARA Para) /* Event Parameter for this timer */ -{ - SK_TIMER **ppTimPrev; - SK_TIMER *pTm; - SK_U32 Delta; - - Time /= 16; /* input is uS, clock ticks are 16uS */ - - if (!Time) - Time = 1; - - SkTimerStop(pAC, Ioc, pTimer); - - pTimer->TmClass = Class; - pTimer->TmEvent = Event; - pTimer->TmPara = Para; - pTimer->TmActive = SK_TRUE; - - if (!pAC->Tim.StQueue) { - /* First Timer to be started */ - pAC->Tim.StQueue = pTimer; - pTimer->TmNext = NULL; - pTimer->TmDelta = Time; - - SkHwtStart(pAC, Ioc, Time); - - return; - } - - /* - * timer correction - */ - timer_done(pAC, Ioc, 0); - - /* - * find position in queue - */ - Delta = 0; - for (ppTimPrev = &pAC->Tim.StQueue; (pTm = *ppTimPrev); - ppTimPrev = &pTm->TmNext ) { - - if (Delta + pTm->TmDelta > Time) { - /* Position found */ - /* Here the timer needs to be inserted. */ - break; - } - Delta += pTm->TmDelta; - } - - /* insert in queue */ - *ppTimPrev = pTimer; - pTimer->TmNext = pTm; - pTimer->TmDelta = Time - Delta; - - if (pTm) { - /* There is a next timer - * -> correct its Delta value. - */ - pTm->TmDelta -= pTimer->TmDelta; - } - - /* restart with first */ - SkHwtStart(pAC, Ioc, pAC->Tim.StQueue->TmDelta); -} - - -void SkTimerDone( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc) /* IoContext */ -{ - timer_done(pAC, Ioc, 1); -} - - -static void timer_done( -SK_AC *pAC, /* Adapters context */ -SK_IOC Ioc, /* IoContext */ -int Restart) /* Do we need to restart the Hardware timer ? */ -{ - SK_U32 Delta; - SK_TIMER *pTm; - SK_TIMER *pTComp; /* Timer completed now now */ - SK_TIMER **ppLast; /* Next field of Last timer to be deq */ - int Done = 0; - - Delta = SkHwtRead(pAC, Ioc); - - ppLast = &pAC->Tim.StQueue; - pTm = pAC->Tim.StQueue; - while (pTm && !Done) { - if (Delta >= pTm->TmDelta) { - /* Timer ran out */ - pTm->TmActive = SK_FALSE; - Delta -= pTm->TmDelta; - ppLast = &pTm->TmNext; - pTm = pTm->TmNext; - } - else { - /* We found the first timer that did not run out */ - pTm->TmDelta -= Delta; - Delta = 0; - Done = 1; - } - } - *ppLast = NULL; - /* - * pTm points to the first Timer that did not run out. - * StQueue points to the first Timer that run out. - */ - - for ( pTComp = pAC->Tim.StQueue; pTComp; pTComp = pTComp->TmNext) { - SkEventQueue(pAC,pTComp->TmClass, pTComp->TmEvent, pTComp->TmPara); - } - - /* Set head of timer queue to the first timer that did not run out */ - pAC->Tim.StQueue = pTm; - - if (Restart && pAC->Tim.StQueue) { - /* Restart HW timer */ - SkHwtStart(pAC, Ioc, pAC->Tim.StQueue->TmDelta); - } -} - -/* End of file */ diff --git a/drivers/net/sk98lin/skvpd.c b/drivers/net/sk98lin/skvpd.c deleted file mode 100644 index 1e662aaebf84..000000000000 --- a/drivers/net/sk98lin/skvpd.c +++ /dev/null @@ -1,1091 +0,0 @@ -/****************************************************************************** - * - * Name: skvpd.c - * Project: GEnesis, PCI Gigabit Ethernet Adapter - * Version: $Revision: 1.37 $ - * Date: $Date: 2003/01/13 10:42:45 $ - * Purpose: Shared software to read and write VPD data - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2003 SysKonnect GmbH. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -/* - Please refer skvpd.txt for information how to include this module - */ -static const char SysKonnectFileId[] = - "@(#)$Id: skvpd.c,v 1.37 2003/01/13 10:42:45 rschmidt Exp $ (C) SK"; - -#include "h/skdrv1st.h" -#include "h/sktypes.h" -#include "h/skdebug.h" -#include "h/skdrv2nd.h" - -/* - * Static functions - */ -#ifndef SK_KR_PROTO -static SK_VPD_PARA *vpd_find_para( - SK_AC *pAC, - const char *key, - SK_VPD_PARA *p); -#else /* SK_KR_PROTO */ -static SK_VPD_PARA *vpd_find_para(); -#endif /* SK_KR_PROTO */ - -/* - * waits for a completion of a VPD transfer - * The VPD transfer must complete within SK_TICKS_PER_SEC/16 - * - * returns 0: success, transfer completes - * error exit(9) with a error message - */ -static int VpdWait( -SK_AC *pAC, /* Adapters context */ -SK_IOC IoC, /* IO Context */ -int event) /* event to wait for (VPD_READ / VPD_write) completion*/ -{ - SK_U64 start_time; - SK_U16 state; - - SK_DBG_MSG(pAC,SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("VPD wait for %s\n", event?"Write":"Read")); - start_time = SkOsGetTime(pAC); - do { - if (SkOsGetTime(pAC) - start_time > SK_TICKS_PER_SEC) { - - /* Bug fix AF: Thu Mar 28 2002 - * Do not call: VPD_STOP(pAC, IoC); - * A pending VPD read cycle can not be aborted by writing - * VPD_WRITE to the PCI_VPD_ADR_REG (VPD address register). - * Although the write threshold in the OUR-register protects - * VPD read only space from being overwritten this does not - * protect a VPD read from being `converted` into a VPD write - * operation (on the fly). As a consequence the VPD_STOP would - * delete VPD read only data. In case of any problems with the - * I2C bus we exit the loop here. The I2C read operation can - * not be aborted except by a reset (->LR). - */ - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_FATAL | SK_DBGCAT_ERR, - ("ERROR:VPD wait timeout\n")); - return(1); - } - - VPD_IN16(pAC, IoC, PCI_VPD_ADR_REG, &state); - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("state = %x, event %x\n",state,event)); - } while((int)(state & PCI_VPD_FLAG) == event); - - return(0); -} - -#ifdef SKDIAG - -/* - * Read the dword at address 'addr' from the VPD EEPROM. - * - * Needed Time: MIN 1,3 ms MAX 2,6 ms - * - * Note: The DWord is returned in the endianess of the machine the routine - * is running on. - * - * Returns the data read. - */ -SK_U32 VpdReadDWord( -SK_AC *pAC, /* Adapters context */ -SK_IOC IoC, /* IO Context */ -int addr) /* VPD address */ -{ - SK_U32 Rtv; - - /* start VPD read */ - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("VPD read dword at 0x%x\n",addr)); - addr &= ~VPD_WRITE; /* ensure the R/W bit is set to read */ - - VPD_OUT16(pAC, IoC, PCI_VPD_ADR_REG, (SK_U16)addr); - - /* ignore return code here */ - (void)VpdWait(pAC, IoC, VPD_READ); - - /* Don't swap here, it's a data stream of bytes */ - Rtv = 0; - - VPD_IN32(pAC, IoC, PCI_VPD_DAT_REG, &Rtv); - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("VPD read dword data = 0x%x\n",Rtv)); - return(Rtv); -} - -#endif /* SKDIAG */ - -/* - * Read one Stream of 'len' bytes of VPD data, starting at 'addr' from - * or to the I2C EEPROM. - * - * Returns number of bytes read / written. - */ -static int VpdWriteStream( -SK_AC *pAC, /* Adapters context */ -SK_IOC IoC, /* IO Context */ -char *buf, /* data buffer */ -int Addr, /* VPD start address */ -int Len) /* number of bytes to read / to write */ -{ - int i; - int j; - SK_U16 AdrReg; - int Rtv; - SK_U8 * pComp; /* Compare pointer */ - SK_U8 Data; /* Input Data for Compare */ - - /* Init Compare Pointer */ - pComp = (SK_U8 *) buf; - - for (i = 0; i < Len; i++, buf++) { - if ((i%sizeof(SK_U32)) == 0) { - /* - * At the begin of each cycle read the Data Reg - * So it is initialized even if only a few bytes - * are written. - */ - AdrReg = (SK_U16) Addr; - AdrReg &= ~VPD_WRITE; /* READ operation */ - - VPD_OUT16(pAC, IoC, PCI_VPD_ADR_REG, AdrReg); - - /* Wait for termination */ - Rtv = VpdWait(pAC, IoC, VPD_READ); - if (Rtv != 0) { - return(i); - } - } - - /* Write current Byte */ - VPD_OUT8(pAC, IoC, PCI_VPD_DAT_REG + (i%sizeof(SK_U32)), - *(SK_U8*)buf); - - if (((i%sizeof(SK_U32)) == 3) || (i == (Len - 1))) { - /* New Address needs to be written to VPD_ADDR reg */ - AdrReg = (SK_U16) Addr; - Addr += sizeof(SK_U32); - AdrReg |= VPD_WRITE; /* WRITE operation */ - - VPD_OUT16(pAC, IoC, PCI_VPD_ADR_REG, AdrReg); - - /* Wait for termination */ - Rtv = VpdWait(pAC, IoC, VPD_WRITE); - if (Rtv != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("Write Timed Out\n")); - return(i - (i%sizeof(SK_U32))); - } - - /* - * Now re-read to verify - */ - AdrReg &= ~VPD_WRITE; /* READ operation */ - - VPD_OUT16(pAC, IoC, PCI_VPD_ADR_REG, AdrReg); - - /* Wait for termination */ - Rtv = VpdWait(pAC, IoC, VPD_READ); - if (Rtv != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("Verify Timed Out\n")); - return(i - (i%sizeof(SK_U32))); - } - - for (j = 0; j <= (int)(i%sizeof(SK_U32)); j++, pComp++) { - - VPD_IN8(pAC, IoC, PCI_VPD_DAT_REG + j, &Data); - - if (Data != *pComp) { - /* Verify Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("WriteStream Verify Error\n")); - return(i - (i%sizeof(SK_U32)) + j); - } - } - } - } - - return(Len); -} - - -/* - * Read one Stream of 'len' bytes of VPD data, starting at 'addr' from - * or to the I2C EEPROM. - * - * Returns number of bytes read / written. - */ -static int VpdReadStream( -SK_AC *pAC, /* Adapters context */ -SK_IOC IoC, /* IO Context */ -char *buf, /* data buffer */ -int Addr, /* VPD start address */ -int Len) /* number of bytes to read / to write */ -{ - int i; - SK_U16 AdrReg; - int Rtv; - - for (i = 0; i < Len; i++, buf++) { - if ((i%sizeof(SK_U32)) == 0) { - /* New Address needs to be written to VPD_ADDR reg */ - AdrReg = (SK_U16) Addr; - Addr += sizeof(SK_U32); - AdrReg &= ~VPD_WRITE; /* READ operation */ - - VPD_OUT16(pAC, IoC, PCI_VPD_ADR_REG, AdrReg); - - /* Wait for termination */ - Rtv = VpdWait(pAC, IoC, VPD_READ); - if (Rtv != 0) { - return(i); - } - } - VPD_IN8(pAC, IoC, PCI_VPD_DAT_REG + (i%sizeof(SK_U32)), - (SK_U8 *)buf); - } - - return(Len); -} - -/* - * Read ore writes 'len' bytes of VPD data, starting at 'addr' from - * or to the I2C EEPROM. - * - * Returns number of bytes read / written. - */ -static int VpdTransferBlock( -SK_AC *pAC, /* Adapters context */ -SK_IOC IoC, /* IO Context */ -char *buf, /* data buffer */ -int addr, /* VPD start address */ -int len, /* number of bytes to read / to write */ -int dir) /* transfer direction may be VPD_READ or VPD_WRITE */ -{ - int Rtv; /* Return value */ - int vpd_rom_size; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("VPD %s block, addr = 0x%x, len = %d\n", - dir ? "write" : "read", addr, len)); - - if (len == 0) - return(0); - - vpd_rom_size = pAC->vpd.rom_size; - - if (addr > vpd_rom_size - 4) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("Address error: 0x%x, exp. < 0x%x\n", - addr, vpd_rom_size - 4)); - return(0); - } - - if (addr + len > vpd_rom_size) { - len = vpd_rom_size - addr; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("Warning: len was cut to %d\n", len)); - } - - if (dir == VPD_READ) { - Rtv = VpdReadStream(pAC, IoC, buf, addr, len); - } - else { - Rtv = VpdWriteStream(pAC, IoC, buf, addr, len); - } - - return(Rtv); -} - -#ifdef SKDIAG - -/* - * Read 'len' bytes of VPD data, starting at 'addr'. - * - * Returns number of bytes read. - */ -int VpdReadBlock( -SK_AC *pAC, /* pAC pointer */ -SK_IOC IoC, /* IO Context */ -char *buf, /* buffer were the data should be stored */ -int addr, /* start reading at the VPD address */ -int len) /* number of bytes to read */ -{ - return(VpdTransferBlock(pAC, IoC, buf, addr, len, VPD_READ)); -} - -/* - * Write 'len' bytes of *but to the VPD EEPROM, starting at 'addr'. - * - * Returns number of bytes writes. - */ -int VpdWriteBlock( -SK_AC *pAC, /* pAC pointer */ -SK_IOC IoC, /* IO Context */ -char *buf, /* buffer, holds the data to write */ -int addr, /* start writing at the VPD address */ -int len) /* number of bytes to write */ -{ - return(VpdTransferBlock(pAC, IoC, buf, addr, len, VPD_WRITE)); -} -#endif /* SKDIAG */ - -/* - * (re)initialize the VPD buffer - * - * Reads the VPD data from the EEPROM into the VPD buffer. - * Get the remaining read only and read / write space. - * - * return 0: success - * 1: fatal VPD error - */ -static int VpdInit( -SK_AC *pAC, /* Adapters context */ -SK_IOC IoC) /* IO Context */ -{ - SK_VPD_PARA *r, rp; /* RW or RV */ - int i; - unsigned char x; - int vpd_size; - SK_U16 dev_id; - SK_U32 our_reg2; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_INIT, ("VpdInit .. ")); - - VPD_IN16(pAC, IoC, PCI_DEVICE_ID, &dev_id); - - VPD_IN32(pAC, IoC, PCI_OUR_REG_2, &our_reg2); - - pAC->vpd.rom_size = 256 << ((our_reg2 & PCI_VPD_ROM_SZ) >> 14); - - /* - * this function might get used before the hardware is initialized - * therefore we cannot always trust in GIChipId - */ - if (((pAC->vpd.v.vpd_status & VPD_VALID) == 0 && - dev_id != VPD_DEV_ID_GENESIS) || - ((pAC->vpd.v.vpd_status & VPD_VALID) != 0 && - !pAC->GIni.GIGenesis)) { - - /* for Yukon the VPD size is always 256 */ - vpd_size = VPD_SIZE_YUKON; - } - else { - /* Genesis uses the maximum ROM size up to 512 for VPD */ - if (pAC->vpd.rom_size > VPD_SIZE_GENESIS) { - vpd_size = VPD_SIZE_GENESIS; - } - else { - vpd_size = pAC->vpd.rom_size; - } - } - - /* read the VPD data into the VPD buffer */ - if (VpdTransferBlock(pAC, IoC, pAC->vpd.vpd_buf, 0, vpd_size, VPD_READ) - != vpd_size) { - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("Block Read Error\n")); - return(1); - } - - pAC->vpd.vpd_size = vpd_size; - - /* Asus K8V Se Deluxe bugfix. Correct VPD content */ - /* MBo April 2004 */ - if (((unsigned char)pAC->vpd.vpd_buf[0x3f] == 0x38) && - ((unsigned char)pAC->vpd.vpd_buf[0x40] == 0x3c) && - ((unsigned char)pAC->vpd.vpd_buf[0x41] == 0x45)) { - printk("sk98lin: Asus mainboard with buggy VPD? " - "Correcting data.\n"); - pAC->vpd.vpd_buf[0x40] = 0x38; - } - - - /* find the end tag of the RO area */ - if (!(r = vpd_find_para(pAC, VPD_RV, &rp))) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("Encoding Error: RV Tag not found\n")); - return(1); - } - - if (r->p_val + r->p_len > pAC->vpd.vpd_buf + vpd_size/2) { - SK_DBG_MSG(pAC,SK_DBGMOD_VPD,SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("Encoding Error: Invalid VPD struct size\n")); - return(1); - } - pAC->vpd.v.vpd_free_ro = r->p_len - 1; - - /* test the checksum */ - for (i = 0, x = 0; (unsigned)i <= (unsigned)vpd_size/2 - r->p_len; i++) { - x += pAC->vpd.vpd_buf[i]; - } - - if (x != 0) { - /* checksum error */ - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("VPD Checksum Error\n")); - return(1); - } - - /* find and check the end tag of the RW area */ - if (!(r = vpd_find_para(pAC, VPD_RW, &rp))) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("Encoding Error: RV Tag not found\n")); - return(1); - } - - if (r->p_val < pAC->vpd.vpd_buf + vpd_size/2) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("Encoding Error: Invalid VPD struct size\n")); - return(1); - } - pAC->vpd.v.vpd_free_rw = r->p_len; - - /* everything seems to be ok */ - if (pAC->GIni.GIChipId != 0) { - pAC->vpd.v.vpd_status |= VPD_VALID; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_INIT, - ("done. Free RO = %d, Free RW = %d\n", - pAC->vpd.v.vpd_free_ro, pAC->vpd.v.vpd_free_rw)); - - return(0); -} - -/* - * find the Keyword 'key' in the VPD buffer and fills the - * parameter struct 'p' with it's values - * - * returns *p success - * 0: parameter was not found or VPD encoding error - */ -static SK_VPD_PARA *vpd_find_para( -SK_AC *pAC, /* common data base */ -const char *key, /* keyword to find (e.g. "MN") */ -SK_VPD_PARA *p) /* parameter description struct */ -{ - char *v ; /* points to VPD buffer */ - int max; /* Maximum Number of Iterations */ - - v = pAC->vpd.vpd_buf; - max = 128; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("VPD find para %s .. ",key)); - - /* check mandatory resource type ID string (Product Name) */ - if (*v != (char)RES_ID) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("Error: 0x%x missing\n", RES_ID)); - return NULL; - } - - if (strcmp(key, VPD_NAME) == 0) { - p->p_len = VPD_GET_RES_LEN(v); - p->p_val = VPD_GET_VAL(v); - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("found, len = %d\n", p->p_len)); - return(p); - } - - v += 3 + VPD_GET_RES_LEN(v) + 3; - for (;; ) { - if (SK_MEMCMP(key,v,2) == 0) { - p->p_len = VPD_GET_VPD_LEN(v); - p->p_val = VPD_GET_VAL(v); - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("found, len = %d\n",p->p_len)); - return(p); - } - - /* exit when reaching the "RW" Tag or the maximum of itera. */ - max--; - if (SK_MEMCMP(VPD_RW,v,2) == 0 || max == 0) { - break; - } - - if (SK_MEMCMP(VPD_RV,v,2) == 0) { - v += 3 + VPD_GET_VPD_LEN(v) + 3; /* skip VPD-W */ - } - else { - v += 3 + VPD_GET_VPD_LEN(v); - } - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("scanning '%c%c' len = %d\n",v[0],v[1],v[2])); - } - -#ifdef DEBUG - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, ("not found\n")); - if (max == 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("Key/Len Encoding error\n")); - } -#endif /* DEBUG */ - return NULL; -} - -/* - * Move 'n' bytes. Begin with the last byte if 'n' is > 0, - * Start with the last byte if n is < 0. - * - * returns nothing - */ -static void vpd_move_para( -char *start, /* start of memory block */ -char *end, /* end of memory block to move */ -int n) /* number of bytes the memory block has to be moved */ -{ - char *p; - int i; /* number of byte copied */ - - if (n == 0) - return; - - i = (int) (end - start + 1); - if (n < 0) { - p = start + n; - while (i != 0) { - *p++ = *start++; - i--; - } - } - else { - p = end + n; - while (i != 0) { - *p-- = *end--; - i--; - } - } -} - -/* - * setup the VPD keyword 'key' at 'ip'. - * - * returns nothing - */ -static void vpd_insert_key( -const char *key, /* keyword to insert */ -const char *buf, /* buffer with the keyword value */ -int len, /* length of the value string */ -char *ip) /* inseration point */ -{ - SK_VPD_KEY *p; - - p = (SK_VPD_KEY *) ip; - p->p_key[0] = key[0]; - p->p_key[1] = key[1]; - p->p_len = (unsigned char) len; - SK_MEMCPY(&p->p_val,buf,len); -} - -/* - * Setup the VPD end tag "RV" / "RW". - * Also correct the remaining space variables vpd_free_ro / vpd_free_rw. - * - * returns 0: success - * 1: encoding error - */ -static int vpd_mod_endtag( -SK_AC *pAC, /* common data base */ -char *etp) /* end pointer input position */ -{ - SK_VPD_KEY *p; - unsigned char x; - int i; - int vpd_size; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("VPD modify endtag at 0x%x = '%c%c'\n",etp,etp[0],etp[1])); - - vpd_size = pAC->vpd.vpd_size; - - p = (SK_VPD_KEY *) etp; - - if (p->p_key[0] != 'R' || (p->p_key[1] != 'V' && p->p_key[1] != 'W')) { - /* something wrong here, encoding error */ - SK_DBG_MSG(pAC,SK_DBGMOD_VPD,SK_DBGCAT_ERR | SK_DBGCAT_FATAL, - ("Encoding Error: invalid end tag\n")); - return(1); - } - if (etp > pAC->vpd.vpd_buf + vpd_size/2) { - /* create "RW" tag */ - p->p_len = (unsigned char)(pAC->vpd.vpd_buf+vpd_size-etp-3-1); - pAC->vpd.v.vpd_free_rw = (int) p->p_len; - i = pAC->vpd.v.vpd_free_rw; - etp += 3; - } - else { - /* create "RV" tag */ - p->p_len = (unsigned char)(pAC->vpd.vpd_buf+vpd_size/2-etp-3); - pAC->vpd.v.vpd_free_ro = (int) p->p_len - 1; - - /* setup checksum */ - for (i = 0, x = 0; i < vpd_size/2 - p->p_len; i++) { - x += pAC->vpd.vpd_buf[i]; - } - p->p_val = (char) 0 - x; - i = pAC->vpd.v.vpd_free_ro; - etp += 4; - } - while (i) { - *etp++ = 0x00; - i--; - } - - return(0); -} - -/* - * Insert a VPD keyword into the VPD buffer. - * - * The keyword 'key' is inserted at the position 'ip' in the - * VPD buffer. - * The keywords behind the input position will - * be moved. The VPD end tag "RV" or "RW" is generated again. - * - * returns 0: success - * 2: value string was cut - * 4: VPD full, keyword was not written - * 6: fatal VPD error - * - */ -static int VpdSetupPara( -SK_AC *pAC, /* common data base */ -const char *key, /* keyword to insert */ -const char *buf, /* buffer with the keyword value */ -int len, /* length of the keyword value */ -int type, /* VPD_RO_KEY or VPD_RW_KEY */ -int op) /* operation to do: ADD_KEY or OWR_KEY */ -{ - SK_VPD_PARA vp; - char *etp; /* end tag position */ - int free; /* remaining space in selected area */ - char *ip; /* input position inside the VPD buffer */ - int rtv; /* return code */ - int head; /* additional haeder bytes to move */ - int found; /* additinoal bytes if the keyword was found */ - int vpd_size; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("VPD setup para key = %s, val = %s\n",key,buf)); - - vpd_size = pAC->vpd.vpd_size; - - rtv = 0; - ip = NULL; - if (type == VPD_RW_KEY) { - /* end tag is "RW" */ - free = pAC->vpd.v.vpd_free_rw; - etp = pAC->vpd.vpd_buf + (vpd_size - free - 1 - 3); - } - else { - /* end tag is "RV" */ - free = pAC->vpd.v.vpd_free_ro; - etp = pAC->vpd.vpd_buf + (vpd_size/2 - free - 4); - } - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("Free RO = %d, Free RW = %d\n", - pAC->vpd.v.vpd_free_ro, pAC->vpd.v.vpd_free_rw)); - - head = 0; - found = 0; - if (op == OWR_KEY) { - if (vpd_find_para(pAC, key, &vp)) { - found = 3; - ip = vp.p_val - 3; - free += vp.p_len + 3; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("Overwrite Key\n")); - } - else { - op = ADD_KEY; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL, - ("Add Key\n")); - } - } - if (op == ADD_KEY) { - ip = etp; - vp.p_len = 0; - head = 3; - } - - if (len + 3 > free) { - if (free < 7) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD Buffer Overflow, keyword not written\n")); - return(4); - } - /* cut it again */ - len = free - 3; - rtv = 2; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD Buffer Full, Keyword was cut\n")); - } - - vpd_move_para(ip + vp.p_len + found, etp+2, len-vp.p_len+head); - vpd_insert_key(key, buf, len, ip); - if (vpd_mod_endtag(pAC, etp + len - vp.p_len + head)) { - pAC->vpd.v.vpd_status &= ~VPD_VALID; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD Encoding Error\n")); - return(6); - } - - return(rtv); -} - - -/* - * Read the contents of the VPD EEPROM and copy it to the - * VPD buffer if not already done. - * - * return: A pointer to the vpd_status structure. The structure contains - * this fields. - */ -SK_VPD_STATUS *VpdStat( -SK_AC *pAC, /* Adapters context */ -SK_IOC IoC) /* IO Context */ -{ - if ((pAC->vpd.v.vpd_status & VPD_VALID) == 0) { - (void)VpdInit(pAC, IoC); - } - return(&pAC->vpd.v); -} - - -/* - * Read the contents of the VPD EEPROM and copy it to the VPD - * buffer if not already done. - * Scan the VPD buffer for VPD keywords and create the VPD - * keyword list by copying the keywords to 'buf', all after - * each other and terminated with a '\0'. - * - * Exceptions: o The Resource Type ID String (product name) is called "Name" - * o The VPD end tags 'RV' and 'RW' are not listed - * - * The number of copied keywords is counted in 'elements'. - * - * returns 0: success - * 2: buffer overfull, one or more keywords are missing - * 6: fatal VPD error - * - * example values after returning: - * - * buf = "Name\0PN\0EC\0MN\0SN\0CP\0VF\0VL\0YA\0" - * *len = 30 - * *elements = 9 - */ -int VpdKeys( -SK_AC *pAC, /* common data base */ -SK_IOC IoC, /* IO Context */ -char *buf, /* buffer where to copy the keywords */ -int *len, /* buffer length */ -int *elements) /* number of keywords returned */ -{ - char *v; - int n; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_RX, ("list VPD keys .. ")); - *elements = 0; - if ((pAC->vpd.v.vpd_status & VPD_VALID) == 0) { - if (VpdInit(pAC, IoC) != 0) { - *len = 0; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD Init Error, terminated\n")); - return(6); - } - } - - if ((signed)strlen(VPD_NAME) + 1 <= *len) { - v = pAC->vpd.vpd_buf; - strcpy(buf,VPD_NAME); - n = strlen(VPD_NAME) + 1; - buf += n; - *elements = 1; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_RX, - ("'%c%c' ",v[0],v[1])); - } - else { - *len = 0; - SK_DBG_MSG(pAC,SK_DBGMOD_VPD,SK_DBGCAT_ERR, - ("buffer overflow\n")); - return(2); - } - - v += 3 + VPD_GET_RES_LEN(v) + 3; - for (;; ) { - /* exit when reaching the "RW" Tag */ - if (SK_MEMCMP(VPD_RW,v,2) == 0) { - break; - } - - if (SK_MEMCMP(VPD_RV,v,2) == 0) { - v += 3 + VPD_GET_VPD_LEN(v) + 3; /* skip VPD-W */ - continue; - } - - if (n+3 <= *len) { - SK_MEMCPY(buf,v,2); - buf += 2; - *buf++ = '\0'; - n += 3; - v += 3 + VPD_GET_VPD_LEN(v); - *elements += 1; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_RX, - ("'%c%c' ",v[0],v[1])); - } - else { - *len = n; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("buffer overflow\n")); - return(2); - } - } - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_RX, ("\n")); - *len = n; - return(0); -} - - -/* - * Read the contents of the VPD EEPROM and copy it to the - * VPD buffer if not already done. Search for the VPD keyword - * 'key' and copy its value to 'buf'. Add a terminating '\0'. - * If the value does not fit into the buffer cut it after - * 'len' - 1 bytes. - * - * returns 0: success - * 1: keyword not found - * 2: value string was cut - * 3: VPD transfer timeout - * 6: fatal VPD error - */ -int VpdRead( -SK_AC *pAC, /* common data base */ -SK_IOC IoC, /* IO Context */ -const char *key, /* keyword to read (e.g. "MN") */ -char *buf, /* buffer where to copy the keyword value */ -int *len) /* buffer length */ -{ - SK_VPD_PARA *p, vp; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_RX, ("VPD read %s .. ", key)); - if ((pAC->vpd.v.vpd_status & VPD_VALID) == 0) { - if (VpdInit(pAC, IoC) != 0) { - *len = 0; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD init error\n")); - return(6); - } - } - - if ((p = vpd_find_para(pAC, key, &vp)) != NULL) { - if (p->p_len > (*(unsigned *)len)-1) { - p->p_len = *len - 1; - } - SK_MEMCPY(buf, p->p_val, p->p_len); - buf[p->p_len] = '\0'; - *len = p->p_len; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_RX, - ("%c%c%c%c.., len = %d\n", - buf[0],buf[1],buf[2],buf[3],*len)); - } - else { - *len = 0; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, ("not found\n")); - return(1); - } - return(0); -} - - -/* - * Check whether a given key may be written - * - * returns - * SK_TRUE Yes it may be written - * SK_FALSE No it may be written - */ -SK_BOOL VpdMayWrite( -char *key) /* keyword to write (allowed values "Yx", "Vx") */ -{ - if ((*key != 'Y' && *key != 'V') || - key[1] < '0' || key[1] > 'Z' || - (key[1] > '9' && key[1] < 'A') || strlen(key) != 2) { - - return(SK_FALSE); - } - return(SK_TRUE); -} - -/* - * Read the contents of the VPD EEPROM and copy it to the VPD - * buffer if not already done. Insert/overwrite the keyword 'key' - * in the VPD buffer. Cut the keyword value if it does not fit - * into the VPD read / write area. - * - * returns 0: success - * 2: value string was cut - * 3: VPD transfer timeout - * 4: VPD full, keyword was not written - * 5: keyword cannot be written - * 6: fatal VPD error - */ -int VpdWrite( -SK_AC *pAC, /* common data base */ -SK_IOC IoC, /* IO Context */ -const char *key, /* keyword to write (allowed values "Yx", "Vx") */ -const char *buf) /* buffer where the keyword value can be read from */ -{ - int len; /* length of the keyword to write */ - int rtv; /* return code */ - int rtv2; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_TX, - ("VPD write %s = %s\n",key,buf)); - - if ((*key != 'Y' && *key != 'V') || - key[1] < '0' || key[1] > 'Z' || - (key[1] > '9' && key[1] < 'A') || strlen(key) != 2) { - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("illegal key tag, keyword not written\n")); - return(5); - } - - if ((pAC->vpd.v.vpd_status & VPD_VALID) == 0) { - if (VpdInit(pAC, IoC) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD init error\n")); - return(6); - } - } - - rtv = 0; - len = strlen(buf); - if (len > VPD_MAX_LEN) { - /* cut it */ - len = VPD_MAX_LEN; - rtv = 2; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("keyword too long, cut after %d bytes\n",VPD_MAX_LEN)); - } - if ((rtv2 = VpdSetupPara(pAC, key, buf, len, VPD_RW_KEY, OWR_KEY)) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD write error\n")); - return(rtv2); - } - - return(rtv); -} - -/* - * Read the contents of the VPD EEPROM and copy it to the - * VPD buffer if not already done. Remove the VPD keyword - * 'key' from the VPD buffer. - * Only the keywords in the read/write area can be deleted. - * Keywords in the read only area cannot be deleted. - * - * returns 0: success, keyword was removed - * 1: keyword not found - * 5: keyword cannot be deleted - * 6: fatal VPD error - */ -int VpdDelete( -SK_AC *pAC, /* common data base */ -SK_IOC IoC, /* IO Context */ -char *key) /* keyword to read (e.g. "MN") */ -{ - SK_VPD_PARA *p, vp; - char *etp; - int vpd_size; - - vpd_size = pAC->vpd.vpd_size; - - SK_DBG_MSG(pAC,SK_DBGMOD_VPD,SK_DBGCAT_TX,("VPD delete key %s\n",key)); - if ((pAC->vpd.v.vpd_status & VPD_VALID) == 0) { - if (VpdInit(pAC, IoC) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD init error\n")); - return(6); - } - } - - if ((p = vpd_find_para(pAC, key, &vp)) != NULL) { - if (p->p_val < pAC->vpd.vpd_buf + vpd_size/2) { - /* try to delete read only keyword */ - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("cannot delete RO keyword\n")); - return(5); - } - - etp = pAC->vpd.vpd_buf + (vpd_size-pAC->vpd.v.vpd_free_rw-1-3); - - vpd_move_para(vp.p_val+vp.p_len, etp+2, - - ((int)(vp.p_len + 3))); - if (vpd_mod_endtag(pAC, etp - vp.p_len - 3)) { - pAC->vpd.v.vpd_status &= ~VPD_VALID; - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("VPD encoding error\n")); - return(6); - } - } - else { - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("keyword not found\n")); - return(1); - } - - return(0); -} - -/* - * If the VPD buffer contains valid data write the VPD - * read/write area back to the VPD EEPROM. - * - * returns 0: success - * 3: VPD transfer timeout - */ -int VpdUpdate( -SK_AC *pAC, /* Adapters context */ -SK_IOC IoC) /* IO Context */ -{ - int vpd_size; - - vpd_size = pAC->vpd.vpd_size; - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_TX, ("VPD update .. ")); - if ((pAC->vpd.v.vpd_status & VPD_VALID) != 0) { - if (VpdTransferBlock(pAC, IoC, pAC->vpd.vpd_buf + vpd_size/2, - vpd_size/2, vpd_size/2, VPD_WRITE) != vpd_size/2) { - - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR, - ("transfer timed out\n")); - return(3); - } - } - SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_TX, ("done\n")); - return(0); -} - diff --git a/drivers/net/sk98lin/skxmac2.c b/drivers/net/sk98lin/skxmac2.c deleted file mode 100644 index b4e75022a657..000000000000 --- a/drivers/net/sk98lin/skxmac2.c +++ /dev/null @@ -1,4160 +0,0 @@ -/****************************************************************************** - * - * Name: skxmac2.c - * Project: Gigabit Ethernet Adapters, Common Modules - * Version: $Revision: 1.102 $ - * Date: $Date: 2003/10/02 16:53:58 $ - * Purpose: Contains functions to initialize the MACs and PHYs - * - ******************************************************************************/ - -/****************************************************************************** - * - * (C)Copyright 1998-2002 SysKonnect. - * (C)Copyright 2002-2003 Marvell. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * The information in this file is provided "AS IS" without warranty. - * - ******************************************************************************/ - -#include "h/skdrv1st.h" -#include "h/skdrv2nd.h" - -/* typedefs *******************************************************************/ - -/* BCOM PHY magic pattern list */ -typedef struct s_PhyHack { - int PhyReg; /* Phy register */ - SK_U16 PhyVal; /* Value to write */ -} BCOM_HACK; - -/* local variables ************************************************************/ - -#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) -static const char SysKonnectFileId[] = - "@(#) $Id: skxmac2.c,v 1.102 2003/10/02 16:53:58 rschmidt Exp $ (C) Marvell."; -#endif - -#ifdef GENESIS -static BCOM_HACK BcomRegA1Hack[] = { - { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1104 }, { 0x17, 0x0013 }, - { 0x15, 0x0404 }, { 0x17, 0x8006 }, { 0x15, 0x0132 }, { 0x17, 0x8006 }, - { 0x15, 0x0232 }, { 0x17, 0x800D }, { 0x15, 0x000F }, { 0x18, 0x0420 }, - { 0, 0 } -}; -static BCOM_HACK BcomRegC0Hack[] = { - { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1204 }, { 0x17, 0x0013 }, - { 0x15, 0x0A04 }, { 0x18, 0x0420 }, - { 0, 0 } -}; -#endif - -/* function prototypes ********************************************************/ -#ifdef GENESIS -static void SkXmInitPhyXmac(SK_AC*, SK_IOC, int, SK_BOOL); -static void SkXmInitPhyBcom(SK_AC*, SK_IOC, int, SK_BOOL); -static int SkXmAutoNegDoneXmac(SK_AC*, SK_IOC, int); -static int SkXmAutoNegDoneBcom(SK_AC*, SK_IOC, int); -#endif /* GENESIS */ -#ifdef YUKON -static void SkGmInitPhyMarv(SK_AC*, SK_IOC, int, SK_BOOL); -static int SkGmAutoNegDoneMarv(SK_AC*, SK_IOC, int); -#endif /* YUKON */ -#ifdef OTHER_PHY -static void SkXmInitPhyLone(SK_AC*, SK_IOC, int, SK_BOOL); -static void SkXmInitPhyNat (SK_AC*, SK_IOC, int, SK_BOOL); -static int SkXmAutoNegDoneLone(SK_AC*, SK_IOC, int); -static int SkXmAutoNegDoneNat (SK_AC*, SK_IOC, int); -#endif /* OTHER_PHY */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmPhyRead() - Read from XMAC PHY register - * - * Description: reads a 16-bit word from XMAC PHY or ext. PHY - * - * Returns: - * nothing - */ -void SkXmPhyRead( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int Port, /* Port Index (MAC_1 + n) */ -int PhyReg, /* Register Address (Offset) */ -SK_U16 SK_FAR *pVal) /* Pointer to Value */ -{ - SK_U16 Mmu; - SK_GEPORT *pPrt; - - pPrt = &pAC->GIni.GP[Port]; - - /* write the PHY register's address */ - XM_OUT16(IoC, Port, XM_PHY_ADDR, PhyReg | pPrt->PhyAddr); - - /* get the PHY register's value */ - XM_IN16(IoC, Port, XM_PHY_DATA, pVal); - - if (pPrt->PhyType != SK_PHY_XMAC) { - do { - XM_IN16(IoC, Port, XM_MMU_CMD, &Mmu); - /* wait until 'Ready' is set */ - } while ((Mmu & XM_MMU_PHY_RDY) == 0); - - /* get the PHY register's value */ - XM_IN16(IoC, Port, XM_PHY_DATA, pVal); - } -} /* SkXmPhyRead */ - - -/****************************************************************************** - * - * SkXmPhyWrite() - Write to XMAC PHY register - * - * Description: writes a 16-bit word to XMAC PHY or ext. PHY - * - * Returns: - * nothing - */ -void SkXmPhyWrite( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int Port, /* Port Index (MAC_1 + n) */ -int PhyReg, /* Register Address (Offset) */ -SK_U16 Val) /* Value */ -{ - SK_U16 Mmu; - SK_GEPORT *pPrt; - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PhyType != SK_PHY_XMAC) { - do { - XM_IN16(IoC, Port, XM_MMU_CMD, &Mmu); - /* wait until 'Busy' is cleared */ - } while ((Mmu & XM_MMU_PHY_BUSY) != 0); - } - - /* write the PHY register's address */ - XM_OUT16(IoC, Port, XM_PHY_ADDR, PhyReg | pPrt->PhyAddr); - - /* write the PHY register's value */ - XM_OUT16(IoC, Port, XM_PHY_DATA, Val); - - if (pPrt->PhyType != SK_PHY_XMAC) { - do { - XM_IN16(IoC, Port, XM_MMU_CMD, &Mmu); - /* wait until 'Busy' is cleared */ - } while ((Mmu & XM_MMU_PHY_BUSY) != 0); - } -} /* SkXmPhyWrite */ -#endif /* GENESIS */ - - -#ifdef YUKON -/****************************************************************************** - * - * SkGmPhyRead() - Read from GPHY register - * - * Description: reads a 16-bit word from GPHY through MDIO - * - * Returns: - * nothing - */ -void SkGmPhyRead( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int Port, /* Port Index (MAC_1 + n) */ -int PhyReg, /* Register Address (Offset) */ -SK_U16 SK_FAR *pVal) /* Pointer to Value */ -{ - SK_U16 Ctrl; - SK_GEPORT *pPrt; -#ifdef VCPU - u_long SimCyle; - u_long SimLowTime; - - VCPUgetTime(&SimCyle, &SimLowTime); - VCPUprintf(0, "SkGmPhyRead(%u), SimCyle=%u, SimLowTime=%u\n", - PhyReg, SimCyle, SimLowTime); -#endif /* VCPU */ - - pPrt = &pAC->GIni.GP[Port]; - - /* set PHY-Register offset and 'Read' OpCode (= 1) */ - *pVal = (SK_U16)(GM_SMI_CT_PHY_AD(pPrt->PhyAddr) | - GM_SMI_CT_REG_AD(PhyReg) | GM_SMI_CT_OP_RD); - - GM_OUT16(IoC, Port, GM_SMI_CTRL, *pVal); - - GM_IN16(IoC, Port, GM_SMI_CTRL, &Ctrl); - - /* additional check for MDC/MDIO activity */ - if ((Ctrl & GM_SMI_CT_BUSY) == 0) { - *pVal = 0; - return; - } - - *pVal |= GM_SMI_CT_BUSY; - - do { -#ifdef VCPU - VCPUwaitTime(1000); -#endif /* VCPU */ - - GM_IN16(IoC, Port, GM_SMI_CTRL, &Ctrl); - - /* wait until 'ReadValid' is set */ - } while (Ctrl == *pVal); - - /* get the PHY register's value */ - GM_IN16(IoC, Port, GM_SMI_DATA, pVal); - -#ifdef VCPU - VCPUgetTime(&SimCyle, &SimLowTime); - VCPUprintf(0, "VCPUgetTime(), SimCyle=%u, SimLowTime=%u\n", - SimCyle, SimLowTime); -#endif /* VCPU */ - -} /* SkGmPhyRead */ - - -/****************************************************************************** - * - * SkGmPhyWrite() - Write to GPHY register - * - * Description: writes a 16-bit word to GPHY through MDIO - * - * Returns: - * nothing - */ -void SkGmPhyWrite( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int Port, /* Port Index (MAC_1 + n) */ -int PhyReg, /* Register Address (Offset) */ -SK_U16 Val) /* Value */ -{ - SK_U16 Ctrl; - SK_GEPORT *pPrt; -#ifdef VCPU - SK_U32 DWord; - u_long SimCyle; - u_long SimLowTime; - - VCPUgetTime(&SimCyle, &SimLowTime); - VCPUprintf(0, "SkGmPhyWrite(Reg=%u, Val=0x%04x), SimCyle=%u, SimLowTime=%u\n", - PhyReg, Val, SimCyle, SimLowTime); -#endif /* VCPU */ - - pPrt = &pAC->GIni.GP[Port]; - - /* write the PHY register's value */ - GM_OUT16(IoC, Port, GM_SMI_DATA, Val); - - /* set PHY-Register offset and 'Write' OpCode (= 0) */ - Val = GM_SMI_CT_PHY_AD(pPrt->PhyAddr) | GM_SMI_CT_REG_AD(PhyReg); - - GM_OUT16(IoC, Port, GM_SMI_CTRL, Val); - - GM_IN16(IoC, Port, GM_SMI_CTRL, &Ctrl); - - /* additional check for MDC/MDIO activity */ - if ((Ctrl & GM_SMI_CT_BUSY) == 0) { - return; - } - - Val |= GM_SMI_CT_BUSY; - - do { -#ifdef VCPU - /* read Timer value */ - SK_IN32(IoC, B2_TI_VAL, &DWord); - - VCPUwaitTime(1000); -#endif /* VCPU */ - - GM_IN16(IoC, Port, GM_SMI_CTRL, &Ctrl); - - /* wait until 'Busy' is cleared */ - } while (Ctrl == Val); - -#ifdef VCPU - VCPUgetTime(&SimCyle, &SimLowTime); - VCPUprintf(0, "VCPUgetTime(), SimCyle=%u, SimLowTime=%u\n", - SimCyle, SimLowTime); -#endif /* VCPU */ - -} /* SkGmPhyWrite */ -#endif /* YUKON */ - - -#ifdef SK_DIAG -/****************************************************************************** - * - * SkGePhyRead() - Read from PHY register - * - * Description: calls a read PHY routine dep. on board type - * - * Returns: - * nothing - */ -void SkGePhyRead( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int Port, /* Port Index (MAC_1 + n) */ -int PhyReg, /* Register Address (Offset) */ -SK_U16 *pVal) /* Pointer to Value */ -{ - void (*r_func)(SK_AC *pAC, SK_IOC IoC, int Port, int Reg, SK_U16 *pVal); - - if (pAC->GIni.GIGenesis) { - r_func = SkXmPhyRead; - } - else { - r_func = SkGmPhyRead; - } - - r_func(pAC, IoC, Port, PhyReg, pVal); -} /* SkGePhyRead */ - - -/****************************************************************************** - * - * SkGePhyWrite() - Write to PHY register - * - * Description: calls a write PHY routine dep. on board type - * - * Returns: - * nothing - */ -void SkGePhyWrite( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* I/O Context */ -int Port, /* Port Index (MAC_1 + n) */ -int PhyReg, /* Register Address (Offset) */ -SK_U16 Val) /* Value */ -{ - void (*w_func)(SK_AC *pAC, SK_IOC IoC, int Port, int Reg, SK_U16 Val); - - if (pAC->GIni.GIGenesis) { - w_func = SkXmPhyWrite; - } - else { - w_func = SkGmPhyWrite; - } - - w_func(pAC, IoC, Port, PhyReg, Val); -} /* SkGePhyWrite */ -#endif /* SK_DIAG */ - - -/****************************************************************************** - * - * SkMacPromiscMode() - Enable / Disable Promiscuous Mode - * - * Description: - * enables / disables promiscuous mode by setting Mode Register (XMAC) or - * Receive Control Register (GMAC) dep. on board type - * - * Returns: - * nothing - */ -void SkMacPromiscMode( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL Enable) /* Enable / Disable */ -{ -#ifdef YUKON - SK_U16 RcReg; -#endif -#ifdef GENESIS - SK_U32 MdReg; -#endif - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - XM_IN32(IoC, Port, XM_MODE, &MdReg); - /* enable or disable promiscuous mode */ - if (Enable) { - MdReg |= XM_MD_ENA_PROM; - } - else { - MdReg &= ~XM_MD_ENA_PROM; - } - /* setup Mode Register */ - XM_OUT32(IoC, Port, XM_MODE, MdReg); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - GM_IN16(IoC, Port, GM_RX_CTRL, &RcReg); - - /* enable or disable unicast and multicast filtering */ - if (Enable) { - RcReg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA); - } - else { - RcReg |= (GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA); - } - /* setup Receive Control Register */ - GM_OUT16(IoC, Port, GM_RX_CTRL, RcReg); - } -#endif /* YUKON */ - -} /* SkMacPromiscMode*/ - - -/****************************************************************************** - * - * SkMacHashing() - Enable / Disable Hashing - * - * Description: - * enables / disables hashing by setting Mode Register (XMAC) or - * Receive Control Register (GMAC) dep. on board type - * - * Returns: - * nothing - */ -void SkMacHashing( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL Enable) /* Enable / Disable */ -{ -#ifdef YUKON - SK_U16 RcReg; -#endif -#ifdef GENESIS - SK_U32 MdReg; -#endif - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - XM_IN32(IoC, Port, XM_MODE, &MdReg); - /* enable or disable hashing */ - if (Enable) { - MdReg |= XM_MD_ENA_HASH; - } - else { - MdReg &= ~XM_MD_ENA_HASH; - } - /* setup Mode Register */ - XM_OUT32(IoC, Port, XM_MODE, MdReg); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - GM_IN16(IoC, Port, GM_RX_CTRL, &RcReg); - - /* enable or disable multicast filtering */ - if (Enable) { - RcReg |= GM_RXCR_MCF_ENA; - } - else { - RcReg &= ~GM_RXCR_MCF_ENA; - } - /* setup Receive Control Register */ - GM_OUT16(IoC, Port, GM_RX_CTRL, RcReg); - } -#endif /* YUKON */ - -} /* SkMacHashing*/ - - -#ifdef SK_DIAG -/****************************************************************************** - * - * SkXmSetRxCmd() - Modify the value of the XMAC's Rx Command Register - * - * Description: - * The features - * - FCS stripping, SK_STRIP_FCS_ON/OFF - * - pad byte stripping, SK_STRIP_PAD_ON/OFF - * - don't set XMR_FS_ERR in status SK_LENERR_OK_ON/OFF - * for inrange length error frames - * - don't set XMR_FS_ERR in status SK_BIG_PK_OK_ON/OFF - * for frames > 1514 bytes - * - enable Rx of own packets SK_SELF_RX_ON/OFF - * - * for incoming packets may be enabled/disabled by this function. - * Additional modes may be added later. - * Multiple modes can be enabled/disabled at the same time. - * The new configuration is written to the Rx Command register immediately. - * - * Returns: - * nothing - */ -static void SkXmSetRxCmd( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -int Mode) /* Mode is SK_STRIP_FCS_ON/OFF, SK_STRIP_PAD_ON/OFF, - SK_LENERR_OK_ON/OFF, or SK_BIG_PK_OK_ON/OFF */ -{ - SK_U16 OldRxCmd; - SK_U16 RxCmd; - - XM_IN16(IoC, Port, XM_RX_CMD, &OldRxCmd); - - RxCmd = OldRxCmd; - - switch (Mode & (SK_STRIP_FCS_ON | SK_STRIP_FCS_OFF)) { - case SK_STRIP_FCS_ON: - RxCmd |= XM_RX_STRIP_FCS; - break; - case SK_STRIP_FCS_OFF: - RxCmd &= ~XM_RX_STRIP_FCS; - break; - } - - switch (Mode & (SK_STRIP_PAD_ON | SK_STRIP_PAD_OFF)) { - case SK_STRIP_PAD_ON: - RxCmd |= XM_RX_STRIP_PAD; - break; - case SK_STRIP_PAD_OFF: - RxCmd &= ~XM_RX_STRIP_PAD; - break; - } - - switch (Mode & (SK_LENERR_OK_ON | SK_LENERR_OK_OFF)) { - case SK_LENERR_OK_ON: - RxCmd |= XM_RX_LENERR_OK; - break; - case SK_LENERR_OK_OFF: - RxCmd &= ~XM_RX_LENERR_OK; - break; - } - - switch (Mode & (SK_BIG_PK_OK_ON | SK_BIG_PK_OK_OFF)) { - case SK_BIG_PK_OK_ON: - RxCmd |= XM_RX_BIG_PK_OK; - break; - case SK_BIG_PK_OK_OFF: - RxCmd &= ~XM_RX_BIG_PK_OK; - break; - } - - switch (Mode & (SK_SELF_RX_ON | SK_SELF_RX_OFF)) { - case SK_SELF_RX_ON: - RxCmd |= XM_RX_SELF_RX; - break; - case SK_SELF_RX_OFF: - RxCmd &= ~XM_RX_SELF_RX; - break; - } - - /* Write the new mode to the Rx command register if required */ - if (OldRxCmd != RxCmd) { - XM_OUT16(IoC, Port, XM_RX_CMD, RxCmd); - } -} /* SkXmSetRxCmd */ - - -/****************************************************************************** - * - * SkGmSetRxCmd() - Modify the value of the GMAC's Rx Control Register - * - * Description: - * The features - * - FCS (CRC) stripping, SK_STRIP_FCS_ON/OFF - * - don't set GMR_FS_LONG_ERR SK_BIG_PK_OK_ON/OFF - * for frames > 1514 bytes - * - enable Rx of own packets SK_SELF_RX_ON/OFF - * - * for incoming packets may be enabled/disabled by this function. - * Additional modes may be added later. - * Multiple modes can be enabled/disabled at the same time. - * The new configuration is written to the Rx Command register immediately. - * - * Returns: - * nothing - */ -static void SkGmSetRxCmd( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -int Mode) /* Mode is SK_STRIP_FCS_ON/OFF, SK_STRIP_PAD_ON/OFF, - SK_LENERR_OK_ON/OFF, or SK_BIG_PK_OK_ON/OFF */ -{ - SK_U16 OldRxCmd; - SK_U16 RxCmd; - - if ((Mode & (SK_STRIP_FCS_ON | SK_STRIP_FCS_OFF)) != 0) { - - GM_IN16(IoC, Port, GM_RX_CTRL, &OldRxCmd); - - RxCmd = OldRxCmd; - - if ((Mode & SK_STRIP_FCS_ON) != 0) { - RxCmd |= GM_RXCR_CRC_DIS; - } - else { - RxCmd &= ~GM_RXCR_CRC_DIS; - } - /* Write the new mode to the Rx control register if required */ - if (OldRxCmd != RxCmd) { - GM_OUT16(IoC, Port, GM_RX_CTRL, RxCmd); - } - } - - if ((Mode & (SK_BIG_PK_OK_ON | SK_BIG_PK_OK_OFF)) != 0) { - - GM_IN16(IoC, Port, GM_SERIAL_MODE, &OldRxCmd); - - RxCmd = OldRxCmd; - - if ((Mode & SK_BIG_PK_OK_ON) != 0) { - RxCmd |= GM_SMOD_JUMBO_ENA; - } - else { - RxCmd &= ~GM_SMOD_JUMBO_ENA; - } - /* Write the new mode to the Rx control register if required */ - if (OldRxCmd != RxCmd) { - GM_OUT16(IoC, Port, GM_SERIAL_MODE, RxCmd); - } - } -} /* SkGmSetRxCmd */ - - -/****************************************************************************** - * - * SkMacSetRxCmd() - Modify the value of the MAC's Rx Control Register - * - * Description: modifies the MAC's Rx Control reg. dep. on board type - * - * Returns: - * nothing - */ -void SkMacSetRxCmd( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -int Mode) /* Rx Mode */ -{ - if (pAC->GIni.GIGenesis) { - - SkXmSetRxCmd(pAC, IoC, Port, Mode); - } - else { - - SkGmSetRxCmd(pAC, IoC, Port, Mode); - } - -} /* SkMacSetRxCmd */ - - -/****************************************************************************** - * - * SkMacCrcGener() - Enable / Disable CRC Generation - * - * Description: enables / disables CRC generation dep. on board type - * - * Returns: - * nothing - */ -void SkMacCrcGener( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL Enable) /* Enable / Disable */ -{ - SK_U16 Word; - - if (pAC->GIni.GIGenesis) { - - XM_IN16(IoC, Port, XM_TX_CMD, &Word); - - if (Enable) { - Word &= ~XM_TX_NO_CRC; - } - else { - Word |= XM_TX_NO_CRC; - } - /* setup Tx Command Register */ - XM_OUT16(IoC, Port, XM_TX_CMD, Word); - } - else { - - GM_IN16(IoC, Port, GM_TX_CTRL, &Word); - - if (Enable) { - Word &= ~GM_TXCR_CRC_DIS; - } - else { - Word |= GM_TXCR_CRC_DIS; - } - /* setup Tx Control Register */ - GM_OUT16(IoC, Port, GM_TX_CTRL, Word); - } - -} /* SkMacCrcGener*/ - -#endif /* SK_DIAG */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmClrExactAddr() - Clear Exact Match Address Registers - * - * Description: - * All Exact Match Address registers of the XMAC 'Port' will be - * cleared starting with 'StartNum' up to (and including) the - * Exact Match address number of 'StopNum'. - * - * Returns: - * nothing - */ -void SkXmClrExactAddr( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -int StartNum, /* Begin with this Address Register Index (0..15) */ -int StopNum) /* Stop after finished with this Register Idx (0..15) */ -{ - int i; - SK_U16 ZeroAddr[3] = {0x0000, 0x0000, 0x0000}; - - if ((unsigned)StartNum > 15 || (unsigned)StopNum > 15 || - StartNum > StopNum) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E001, SKERR_HWI_E001MSG); - return; - } - - for (i = StartNum; i <= StopNum; i++) { - XM_OUTADDR(IoC, Port, XM_EXM(i), &ZeroAddr[0]); - } -} /* SkXmClrExactAddr */ -#endif /* GENESIS */ - - -/****************************************************************************** - * - * SkMacFlushTxFifo() - Flush the MAC's transmit FIFO - * - * Description: - * Flush the transmit FIFO of the MAC specified by the index 'Port' - * - * Returns: - * nothing - */ -void SkMacFlushTxFifo( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ -#ifdef GENESIS - SK_U32 MdReg; - - if (pAC->GIni.GIGenesis) { - - XM_IN32(IoC, Port, XM_MODE, &MdReg); - - XM_OUT32(IoC, Port, XM_MODE, MdReg | XM_MD_FTF); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* no way to flush the FIFO we have to issue a reset */ - /* TBD */ - } -#endif /* YUKON */ - -} /* SkMacFlushTxFifo */ - - -/****************************************************************************** - * - * SkMacFlushRxFifo() - Flush the MAC's receive FIFO - * - * Description: - * Flush the receive FIFO of the MAC specified by the index 'Port' - * - * Returns: - * nothing - */ -static void SkMacFlushRxFifo( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ -#ifdef GENESIS - SK_U32 MdReg; - - if (pAC->GIni.GIGenesis) { - - XM_IN32(IoC, Port, XM_MODE, &MdReg); - - XM_OUT32(IoC, Port, XM_MODE, MdReg | XM_MD_FRF); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* no way to flush the FIFO we have to issue a reset */ - /* TBD */ - } -#endif /* YUKON */ - -} /* SkMacFlushRxFifo */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmSoftRst() - Do a XMAC software reset - * - * Description: - * The PHY registers should not be destroyed during this - * kind of software reset. Therefore the XMAC Software Reset - * (XM_GP_RES_MAC bit in XM_GP_PORT) must not be used! - * - * The software reset is done by - * - disabling the Rx and Tx state machine, - * - resetting the statistics module, - * - clear all other significant XMAC Mode, - * Command, and Control Registers - * - clearing the Hash Register and the - * Exact Match Address registers, and - * - flushing the XMAC's Rx and Tx FIFOs. - * - * Note: - * Another requirement when stopping the XMAC is to - * avoid sending corrupted frames on the network. - * Disabling the Tx state machine will NOT interrupt - * the currently transmitted frame. But we must take care - * that the Tx FIFO is cleared AFTER the current frame - * is complete sent to the network. - * - * It takes about 12ns to send a frame with 1538 bytes. - * One PCI clock goes at least 15ns (66MHz). Therefore - * after reading XM_GP_PORT back, we are sure that the - * transmitter is disabled AND idle. And this means - * we may flush the transmit FIFO now. - * - * Returns: - * nothing - */ -static void SkXmSoftRst( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U16 ZeroAddr[4] = {0x0000, 0x0000, 0x0000, 0x0000}; - - /* reset the statistics module */ - XM_OUT32(IoC, Port, XM_GP_PORT, XM_GP_RES_STAT); - - /* disable all XMAC IRQs */ - XM_OUT16(IoC, Port, XM_IMSK, 0xffff); - - XM_OUT32(IoC, Port, XM_MODE, 0); /* clear Mode Reg */ - - XM_OUT16(IoC, Port, XM_TX_CMD, 0); /* reset TX CMD Reg */ - XM_OUT16(IoC, Port, XM_RX_CMD, 0); /* reset RX CMD Reg */ - - /* disable all PHY IRQs */ - switch (pAC->GIni.GP[Port].PhyType) { - case SK_PHY_BCOM: - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_INT_MASK, 0xffff); - break; -#ifdef OTHER_PHY - case SK_PHY_LONE: - SkXmPhyWrite(pAC, IoC, Port, PHY_LONE_INT_ENAB, 0); - break; - case SK_PHY_NAT: - /* todo: National - SkXmPhyWrite(pAC, IoC, Port, PHY_NAT_INT_MASK, 0xffff); */ - break; -#endif /* OTHER_PHY */ - } - - /* clear the Hash Register */ - XM_OUTHASH(IoC, Port, XM_HSM, &ZeroAddr); - - /* clear the Exact Match Address registers */ - SkXmClrExactAddr(pAC, IoC, Port, 0, 15); - - /* clear the Source Check Address registers */ - XM_OUTHASH(IoC, Port, XM_SRC_CHK, &ZeroAddr); - -} /* SkXmSoftRst */ - - -/****************************************************************************** - * - * SkXmHardRst() - Do a XMAC hardware reset - * - * Description: - * The XMAC of the specified 'Port' and all connected devices - * (PHY and SERDES) will receive a reset signal on its *Reset pins. - * External PHYs must be reset by clearing a bit in the GPIO register - * (Timing requirements: Broadcom: 400ns, Level One: none, National: 80ns). - * - * ATTENTION: - * It is absolutely necessary to reset the SW_RST Bit first - * before calling this function. - * - * Returns: - * nothing - */ -static void SkXmHardRst( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U32 Reg; - int i; - int TOut; - SK_U16 Word; - - for (i = 0; i < 4; i++) { - /* TX_MFF_CTRL1 has 32 bits, but only the lowest 16 bits are used */ - SK_OUT16(IoC, MR_ADDR(Port, TX_MFF_CTRL1), MFF_CLR_MAC_RST); - - TOut = 0; - do { - if (TOut++ > 10000) { - /* - * Adapter seems to be in RESET state. - * Registers cannot be written. - */ - return; - } - - SK_OUT16(IoC, MR_ADDR(Port, TX_MFF_CTRL1), MFF_SET_MAC_RST); - - SK_IN16(IoC, MR_ADDR(Port, TX_MFF_CTRL1), &Word); - - } while ((Word & MFF_SET_MAC_RST) == 0); - } - - /* For external PHYs there must be special handling */ - if (pAC->GIni.GP[Port].PhyType != SK_PHY_XMAC) { - - SK_IN32(IoC, B2_GP_IO, &Reg); - - if (Port == 0) { - Reg |= GP_DIR_0; /* set to output */ - Reg &= ~GP_IO_0; /* set PHY reset (active low) */ - } - else { - Reg |= GP_DIR_2; /* set to output */ - Reg &= ~GP_IO_2; /* set PHY reset (active low) */ - } - /* reset external PHY */ - SK_OUT32(IoC, B2_GP_IO, Reg); - - /* short delay */ - SK_IN32(IoC, B2_GP_IO, &Reg); - } -} /* SkXmHardRst */ - - -/****************************************************************************** - * - * SkXmClearRst() - Release the PHY & XMAC reset - * - * Description: - * - * Returns: - * nothing - */ -static void SkXmClearRst( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U32 DWord; - - /* clear HW reset */ - SK_OUT16(IoC, MR_ADDR(Port, TX_MFF_CTRL1), MFF_CLR_MAC_RST); - - if (pAC->GIni.GP[Port].PhyType != SK_PHY_XMAC) { - - SK_IN32(IoC, B2_GP_IO, &DWord); - - if (Port == 0) { - DWord |= (GP_DIR_0 | GP_IO_0); /* set to output */ - } - else { - DWord |= (GP_DIR_2 | GP_IO_2); /* set to output */ - } - /* Clear PHY reset */ - SK_OUT32(IoC, B2_GP_IO, DWord); - - /* Enable GMII interface */ - XM_OUT16(IoC, Port, XM_HW_CFG, XM_HW_GMII_MD); - } -} /* SkXmClearRst */ -#endif /* GENESIS */ - - -#ifdef YUKON -/****************************************************************************** - * - * SkGmSoftRst() - Do a GMAC software reset - * - * Description: - * The GPHY registers should not be destroyed during this - * kind of software reset. - * - * Returns: - * nothing - */ -static void SkGmSoftRst( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U16 EmptyHash[4] = {0x0000, 0x0000, 0x0000, 0x0000}; - SK_U16 RxCtrl; - - /* reset the statistics module */ - - /* disable all GMAC IRQs */ - SK_OUT8(IoC, GMAC_IRQ_MSK, 0); - - /* disable all PHY IRQs */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_INT_MASK, 0); - - /* clear the Hash Register */ - GM_OUTHASH(IoC, Port, GM_MC_ADDR_H1, EmptyHash); - - /* Enable Unicast and Multicast filtering */ - GM_IN16(IoC, Port, GM_RX_CTRL, &RxCtrl); - - GM_OUT16(IoC, Port, GM_RX_CTRL, - (SK_U16)(RxCtrl | GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA)); - -} /* SkGmSoftRst */ - - -/****************************************************************************** - * - * SkGmHardRst() - Do a GMAC hardware reset - * - * Description: - * - * Returns: - * nothing - */ -static void SkGmHardRst( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U32 DWord; - - /* WA code for COMA mode */ - if (pAC->GIni.GIYukonLite && - pAC->GIni.GIChipRev >= CHIP_REV_YU_LITE_A3) { - - SK_IN32(IoC, B2_GP_IO, &DWord); - - DWord |= (GP_DIR_9 | GP_IO_9); - - /* set PHY reset */ - SK_OUT32(IoC, B2_GP_IO, DWord); - } - - /* set GPHY Control reset */ - SK_OUT32(IoC, MR_ADDR(Port, GPHY_CTRL), GPC_RST_SET); - - /* set GMAC Control reset */ - SK_OUT32(IoC, MR_ADDR(Port, GMAC_CTRL), GMC_RST_SET); - -} /* SkGmHardRst */ - - -/****************************************************************************** - * - * SkGmClearRst() - Release the GPHY & GMAC reset - * - * Description: - * - * Returns: - * nothing - */ -static void SkGmClearRst( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U32 DWord; - -#ifdef XXX - /* clear GMAC Control reset */ - SK_OUT32(IoC, MR_ADDR(Port, GMAC_CTRL), GMC_RST_CLR); - - /* set GMAC Control reset */ - SK_OUT32(IoC, MR_ADDR(Port, GMAC_CTRL), GMC_RST_SET); -#endif /* XXX */ - - /* WA code for COMA mode */ - if (pAC->GIni.GIYukonLite && - pAC->GIni.GIChipRev >= CHIP_REV_YU_LITE_A3) { - - SK_IN32(IoC, B2_GP_IO, &DWord); - - DWord |= GP_DIR_9; /* set to output */ - DWord &= ~GP_IO_9; /* clear PHY reset (active high) */ - - /* clear PHY reset */ - SK_OUT32(IoC, B2_GP_IO, DWord); - } - - /* set HWCFG_MODE */ - DWord = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP | - GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE | - (pAC->GIni.GICopperType ? GPC_HWCFG_GMII_COP : - GPC_HWCFG_GMII_FIB); - - /* set GPHY Control reset */ - SK_OUT32(IoC, MR_ADDR(Port, GPHY_CTRL), DWord | GPC_RST_SET); - - /* release GPHY Control reset */ - SK_OUT32(IoC, MR_ADDR(Port, GPHY_CTRL), DWord | GPC_RST_CLR); - -#ifdef VCPU - VCpuWait(9000); -#endif /* VCPU */ - - /* clear GMAC Control reset */ - SK_OUT32(IoC, MR_ADDR(Port, GMAC_CTRL), GMC_PAUSE_ON | GMC_RST_CLR); - -#ifdef VCPU - VCpuWait(2000); - - SK_IN32(IoC, MR_ADDR(Port, GPHY_CTRL), &DWord); - - SK_IN32(IoC, B0_ISRC, &DWord); -#endif /* VCPU */ - -} /* SkGmClearRst */ -#endif /* YUKON */ - - -/****************************************************************************** - * - * SkMacSoftRst() - Do a MAC software reset - * - * Description: calls a MAC software reset routine dep. on board type - * - * Returns: - * nothing - */ -void SkMacSoftRst( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - - pPrt = &pAC->GIni.GP[Port]; - - /* disable receiver and transmitter */ - SkMacRxTxDisable(pAC, IoC, Port); - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - SkXmSoftRst(pAC, IoC, Port); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - SkGmSoftRst(pAC, IoC, Port); - } -#endif /* YUKON */ - - /* flush the MAC's Rx and Tx FIFOs */ - SkMacFlushTxFifo(pAC, IoC, Port); - - SkMacFlushRxFifo(pAC, IoC, Port); - - pPrt->PState = SK_PRT_STOP; - -} /* SkMacSoftRst */ - - -/****************************************************************************** - * - * SkMacHardRst() - Do a MAC hardware reset - * - * Description: calls a MAC hardware reset routine dep. on board type - * - * Returns: - * nothing - */ -void SkMacHardRst( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - SkXmHardRst(pAC, IoC, Port); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - SkGmHardRst(pAC, IoC, Port); - } -#endif /* YUKON */ - - pAC->GIni.GP[Port].PState = SK_PRT_RESET; - -} /* SkMacHardRst */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmInitMac() - Initialize the XMAC II - * - * Description: - * Initialize the XMAC of the specified port. - * The XMAC must be reset or stopped before calling this function. - * - * Note: - * The XMAC's Rx and Tx state machine is still disabled when returning. - * - * Returns: - * nothing - */ -void SkXmInitMac( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - int i; - SK_U16 SWord; - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PState == SK_PRT_STOP) { - /* Port State: SK_PRT_STOP */ - /* Verify that the reset bit is cleared */ - SK_IN16(IoC, MR_ADDR(Port, TX_MFF_CTRL1), &SWord); - - if ((SWord & MFF_SET_MAC_RST) != 0) { - /* PState does not match HW state */ - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E006, SKERR_HWI_E006MSG); - /* Correct it */ - pPrt->PState = SK_PRT_RESET; - } - } - - if (pPrt->PState == SK_PRT_RESET) { - - SkXmClearRst(pAC, IoC, Port); - - if (pPrt->PhyType != SK_PHY_XMAC) { - /* read Id from external PHY (all have the same address) */ - SkXmPhyRead(pAC, IoC, Port, PHY_XMAC_ID1, &pPrt->PhyId1); - - /* - * Optimize MDIO transfer by suppressing preamble. - * Must be done AFTER first access to BCOM chip. - */ - XM_IN16(IoC, Port, XM_MMU_CMD, &SWord); - - XM_OUT16(IoC, Port, XM_MMU_CMD, SWord | XM_MMU_NO_PRE); - - if (pPrt->PhyId1 == PHY_BCOM_ID1_C0) { - /* - * Workaround BCOM Errata for the C0 type. - * Write magic patterns to reserved registers. - */ - i = 0; - while (BcomRegC0Hack[i].PhyReg != 0) { - SkXmPhyWrite(pAC, IoC, Port, BcomRegC0Hack[i].PhyReg, - BcomRegC0Hack[i].PhyVal); - i++; - } - } - else if (pPrt->PhyId1 == PHY_BCOM_ID1_A1) { - /* - * Workaround BCOM Errata for the A1 type. - * Write magic patterns to reserved registers. - */ - i = 0; - while (BcomRegA1Hack[i].PhyReg != 0) { - SkXmPhyWrite(pAC, IoC, Port, BcomRegA1Hack[i].PhyReg, - BcomRegA1Hack[i].PhyVal); - i++; - } - } - - /* - * Workaround BCOM Errata (#10523) for all BCom PHYs. - * Disable Power Management after reset. - */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, &SWord); - - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, - (SK_U16)(SWord | PHY_B_AC_DIS_PM)); - - /* PHY LED initialization is done in SkGeXmitLED() */ - } - - /* Dummy read the Interrupt source register */ - XM_IN16(IoC, Port, XM_ISRC, &SWord); - - /* - * The auto-negotiation process starts immediately after - * clearing the reset. The auto-negotiation process should be - * started by the SIRQ, therefore stop it here immediately. - */ - SkMacInitPhy(pAC, IoC, Port, SK_FALSE); - -#ifdef TEST_ONLY - /* temp. code: enable signal detect */ - /* WARNING: do not override GMII setting above */ - XM_OUT16(IoC, Port, XM_HW_CFG, XM_HW_COM4SIG); -#endif - } - - /* - * configure the XMACs Station Address - * B2_MAC_2 = xx xx xx xx xx x1 is programmed to XMAC A - * B2_MAC_3 = xx xx xx xx xx x2 is programmed to XMAC B - */ - for (i = 0; i < 3; i++) { - /* - * The following 2 statements are together endianess - * independent. Remember this when changing. - */ - SK_IN16(IoC, (B2_MAC_2 + Port * 8 + i * 2), &SWord); - - XM_OUT16(IoC, Port, (XM_SA + i * 2), SWord); - } - - /* Tx Inter Packet Gap (XM_TX_IPG): use default */ - /* Tx High Water Mark (XM_TX_HI_WM): use default */ - /* Tx Low Water Mark (XM_TX_LO_WM): use default */ - /* Host Request Threshold (XM_HT_THR): use default */ - /* Rx Request Threshold (XM_RX_THR): use default */ - /* Rx Low Water Mark (XM_RX_LO_WM): use default */ - - /* configure Rx High Water Mark (XM_RX_HI_WM) */ - XM_OUT16(IoC, Port, XM_RX_HI_WM, SK_XM_RX_HI_WM); - - /* Configure Tx Request Threshold */ - SWord = SK_XM_THR_SL; /* for single port */ - - if (pAC->GIni.GIMacsFound > 1) { - switch (pAC->GIni.GIPortUsage) { - case SK_RED_LINK: - SWord = SK_XM_THR_REDL; /* redundant link */ - break; - case SK_MUL_LINK: - SWord = SK_XM_THR_MULL; /* load balancing */ - break; - case SK_JUMBO_LINK: - SWord = SK_XM_THR_JUMBO; /* jumbo frames */ - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E014, SKERR_HWI_E014MSG); - break; - } - } - XM_OUT16(IoC, Port, XM_TX_THR, SWord); - - /* setup register defaults for the Tx Command Register */ - XM_OUT16(IoC, Port, XM_TX_CMD, XM_TX_AUTO_PAD); - - /* setup register defaults for the Rx Command Register */ - SWord = XM_RX_STRIP_FCS | XM_RX_LENERR_OK; - - if (pAC->GIni.GIPortUsage == SK_JUMBO_LINK) { - SWord |= XM_RX_BIG_PK_OK; - } - - if (pPrt->PLinkMode == SK_LMODE_HALF) { - /* - * If in manual half duplex mode the other side might be in - * full duplex mode, so ignore if a carrier extension is not seen - * on frames received - */ - SWord |= XM_RX_DIS_CEXT; - } - - XM_OUT16(IoC, Port, XM_RX_CMD, SWord); - - /* - * setup register defaults for the Mode Register - * - Don't strip error frames to avoid Store & Forward - * on the Rx side. - * - Enable 'Check Station Address' bit - * - Enable 'Check Address Array' bit - */ - XM_OUT32(IoC, Port, XM_MODE, XM_DEF_MODE); - - /* - * Initialize the Receive Counter Event Mask (XM_RX_EV_MSK) - * - Enable all bits excepting 'Octets Rx OK Low CntOv' - * and 'Octets Rx OK Hi Cnt Ov'. - */ - XM_OUT32(IoC, Port, XM_RX_EV_MSK, XMR_DEF_MSK); - - /* - * Initialize the Transmit Counter Event Mask (XM_TX_EV_MSK) - * - Enable all bits excepting 'Octets Tx OK Low CntOv' - * and 'Octets Tx OK Hi Cnt Ov'. - */ - XM_OUT32(IoC, Port, XM_TX_EV_MSK, XMT_DEF_MSK); - - /* - * Do NOT init XMAC interrupt mask here. - * All interrupts remain disable until link comes up! - */ - - /* - * Any additional configuration changes may be done now. - * The last action is to enable the Rx and Tx state machine. - * This should be done after the auto-negotiation process - * has been completed successfully. - */ -} /* SkXmInitMac */ -#endif /* GENESIS */ - - -#ifdef YUKON -/****************************************************************************** - * - * SkGmInitMac() - Initialize the GMAC - * - * Description: - * Initialize the GMAC of the specified port. - * The GMAC must be reset or stopped before calling this function. - * - * Note: - * The GMAC's Rx and Tx state machine is still disabled when returning. - * - * Returns: - * nothing - */ -void SkGmInitMac( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - int i; - SK_U16 SWord; - SK_U32 DWord; - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PState == SK_PRT_STOP) { - /* Port State: SK_PRT_STOP */ - /* Verify that the reset bit is cleared */ - SK_IN32(IoC, MR_ADDR(Port, GMAC_CTRL), &DWord); - - if ((DWord & GMC_RST_SET) != 0) { - /* PState does not match HW state */ - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E006, SKERR_HWI_E006MSG); - /* Correct it */ - pPrt->PState = SK_PRT_RESET; - } - } - - if (pPrt->PState == SK_PRT_RESET) { - - SkGmHardRst(pAC, IoC, Port); - - SkGmClearRst(pAC, IoC, Port); - - /* Auto-negotiation ? */ - if (pPrt->PLinkMode == SK_LMODE_HALF || pPrt->PLinkMode == SK_LMODE_FULL) { - /* Auto-negotiation disabled */ - - /* get General Purpose Control */ - GM_IN16(IoC, Port, GM_GP_CTRL, &SWord); - - /* disable auto-update for speed, duplex and flow-control */ - SWord |= GM_GPCR_AU_ALL_DIS; - - /* setup General Purpose Control Register */ - GM_OUT16(IoC, Port, GM_GP_CTRL, SWord); - - SWord = GM_GPCR_AU_ALL_DIS; - } - else { - SWord = 0; - } - - /* speed settings */ - switch (pPrt->PLinkSpeed) { - case SK_LSPEED_AUTO: - case SK_LSPEED_1000MBPS: - SWord |= GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100; - break; - case SK_LSPEED_100MBPS: - SWord |= GM_GPCR_SPEED_100; - break; - case SK_LSPEED_10MBPS: - break; - } - - /* duplex settings */ - if (pPrt->PLinkMode != SK_LMODE_HALF) { - /* set full duplex */ - SWord |= GM_GPCR_DUP_FULL; - } - - /* flow-control settings */ - switch (pPrt->PFlowCtrlMode) { - case SK_FLOW_MODE_NONE: - /* set Pause Off */ - SK_OUT32(IoC, MR_ADDR(Port, GMAC_CTRL), GMC_PAUSE_OFF); - /* disable Tx & Rx flow-control */ - SWord |= GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS; - break; - case SK_FLOW_MODE_LOC_SEND: - /* disable Rx flow-control */ - SWord |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS; - break; - case SK_FLOW_MODE_SYMMETRIC: - case SK_FLOW_MODE_SYM_OR_REM: - /* enable Tx & Rx flow-control */ - break; - } - - /* setup General Purpose Control Register */ - GM_OUT16(IoC, Port, GM_GP_CTRL, SWord); - - /* dummy read the Interrupt Source Register */ - SK_IN16(IoC, GMAC_IRQ_SRC, &SWord); - -#ifndef VCPU - /* read Id from PHY */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_ID1, &pPrt->PhyId1); - - SkGmInitPhyMarv(pAC, IoC, Port, SK_FALSE); -#endif /* VCPU */ - } - - (void)SkGmResetCounter(pAC, IoC, Port); - - /* setup Transmit Control Register */ - GM_OUT16(IoC, Port, GM_TX_CTRL, TX_COL_THR(pPrt->PMacColThres)); - - /* setup Receive Control Register */ - GM_OUT16(IoC, Port, GM_RX_CTRL, GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA | - GM_RXCR_CRC_DIS); - - /* setup Transmit Flow Control Register */ - GM_OUT16(IoC, Port, GM_TX_FLOW_CTRL, 0xffff); - - /* setup Transmit Parameter Register */ -#ifdef VCPU - GM_IN16(IoC, Port, GM_TX_PARAM, &SWord); -#endif /* VCPU */ - - SWord = TX_JAM_LEN_VAL(pPrt->PMacJamLen) | - TX_JAM_IPG_VAL(pPrt->PMacJamIpgVal) | - TX_IPG_JAM_DATA(pPrt->PMacJamIpgData); - - GM_OUT16(IoC, Port, GM_TX_PARAM, SWord); - - /* configure the Serial Mode Register */ -#ifdef VCPU - GM_IN16(IoC, Port, GM_SERIAL_MODE, &SWord); -#endif /* VCPU */ - - SWord = GM_SMOD_VLAN_ENA | IPG_DATA_VAL(pPrt->PMacIpgData); - - if (pPrt->PMacLimit4) { - /* reset of collision counter after 4 consecutive collisions */ - SWord |= GM_SMOD_LIMIT_4; - } - - if (pAC->GIni.GIPortUsage == SK_JUMBO_LINK) { - /* enable jumbo mode (Max. Frame Length = 9018) */ - SWord |= GM_SMOD_JUMBO_ENA; - } - - GM_OUT16(IoC, Port, GM_SERIAL_MODE, SWord); - - /* - * configure the GMACs Station Addresses - * in PROM you can find our addresses at: - * B2_MAC_1 = xx xx xx xx xx x0 virtual address - * B2_MAC_2 = xx xx xx xx xx x1 is programmed to GMAC A - * B2_MAC_3 = xx xx xx xx xx x2 is reserved for DualPort - */ - - for (i = 0; i < 3; i++) { - /* - * The following 2 statements are together endianess - * independent. Remember this when changing. - */ - /* physical address: will be used for pause frames */ - SK_IN16(IoC, (B2_MAC_2 + Port * 8 + i * 2), &SWord); - -#ifdef WA_DEV_16 - /* WA for deviation #16 */ - if (pAC->GIni.GIChipId == CHIP_ID_YUKON && pAC->GIni.GIChipRev == 0) { - /* swap the address bytes */ - SWord = ((SWord & 0xff00) >> 8) | ((SWord & 0x00ff) << 8); - - /* write to register in reversed order */ - GM_OUT16(IoC, Port, (GM_SRC_ADDR_1L + (2 - i) * 4), SWord); - } - else { - GM_OUT16(IoC, Port, (GM_SRC_ADDR_1L + i * 4), SWord); - } -#else - GM_OUT16(IoC, Port, (GM_SRC_ADDR_1L + i * 4), SWord); -#endif /* WA_DEV_16 */ - - /* virtual address: will be used for data */ - SK_IN16(IoC, (B2_MAC_1 + Port * 8 + i * 2), &SWord); - - GM_OUT16(IoC, Port, (GM_SRC_ADDR_2L + i * 4), SWord); - - /* reset Multicast filtering Hash registers 1-3 */ - GM_OUT16(IoC, Port, GM_MC_ADDR_H1 + 4*i, 0); - } - - /* reset Multicast filtering Hash register 4 */ - GM_OUT16(IoC, Port, GM_MC_ADDR_H4, 0); - - /* enable interrupt mask for counter overflows */ - GM_OUT16(IoC, Port, GM_TX_IRQ_MSK, 0); - GM_OUT16(IoC, Port, GM_RX_IRQ_MSK, 0); - GM_OUT16(IoC, Port, GM_TR_IRQ_MSK, 0); - -#if defined(SK_DIAG) || defined(DEBUG) - /* read General Purpose Status */ - GM_IN16(IoC, Port, GM_GP_STAT, &SWord); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("MAC Stat Reg.=0x%04X\n", SWord)); -#endif /* SK_DIAG || DEBUG */ - -#ifdef SK_DIAG - c_print("MAC Stat Reg=0x%04X\n", SWord); -#endif /* SK_DIAG */ - -} /* SkGmInitMac */ -#endif /* YUKON */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmInitDupMd() - Initialize the XMACs Duplex Mode - * - * Description: - * This function initializes the XMACs Duplex Mode. - * It should be called after successfully finishing - * the Auto-negotiation Process - * - * Returns: - * nothing - */ -static void SkXmInitDupMd( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - switch (pAC->GIni.GP[Port].PLinkModeStatus) { - case SK_LMODE_STAT_AUTOHALF: - case SK_LMODE_STAT_HALF: - /* Configuration Actions for Half Duplex Mode */ - /* - * XM_BURST = default value. We are probable not quick - * enough at the 'XMAC' bus to burst 8kB. - * The XMAC stops bursting if no transmit frames - * are available or the burst limit is exceeded. - */ - /* XM_TX_RT_LIM = default value (15) */ - /* XM_TX_STIME = default value (0xff = 4096 bit times) */ - break; - case SK_LMODE_STAT_AUTOFULL: - case SK_LMODE_STAT_FULL: - /* Configuration Actions for Full Duplex Mode */ - /* - * The duplex mode is configured by the PHY, - * therefore it seems to be that there is nothing - * to do here. - */ - break; - case SK_LMODE_STAT_UNKNOWN: - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E007, SKERR_HWI_E007MSG); - break; - } -} /* SkXmInitDupMd */ - - -/****************************************************************************** - * - * SkXmInitPauseMd() - initialize the Pause Mode to be used for this port - * - * Description: - * This function initializes the Pause Mode which should - * be used for this port. - * It should be called after successfully finishing - * the Auto-negotiation Process - * - * Returns: - * nothing - */ -static void SkXmInitPauseMd( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U32 DWord; - SK_U16 Word; - - pPrt = &pAC->GIni.GP[Port]; - - XM_IN16(IoC, Port, XM_MMU_CMD, &Word); - - if (pPrt->PFlowCtrlStatus == SK_FLOW_STAT_NONE || - pPrt->PFlowCtrlStatus == SK_FLOW_STAT_LOC_SEND) { - - /* Disable Pause Frame Reception */ - Word |= XM_MMU_IGN_PF; - } - else { - /* - * enabling pause frame reception is required for 1000BT - * because the XMAC is not reset if the link is going down - */ - /* Enable Pause Frame Reception */ - Word &= ~XM_MMU_IGN_PF; - } - - XM_OUT16(IoC, Port, XM_MMU_CMD, Word); - - XM_IN32(IoC, Port, XM_MODE, &DWord); - - if (pPrt->PFlowCtrlStatus == SK_FLOW_STAT_SYMMETRIC || - pPrt->PFlowCtrlStatus == SK_FLOW_STAT_LOC_SEND) { - - /* - * Configure Pause Frame Generation - * Use internal and external Pause Frame Generation. - * Sending pause frames is edge triggered. - * Send a Pause frame with the maximum pause time if - * internal oder external FIFO full condition occurs. - * Send a zero pause time frame to re-start transmission. - */ - - /* XM_PAUSE_DA = '010000C28001' (default) */ - - /* XM_MAC_PTIME = 0xffff (maximum) */ - /* remember this value is defined in big endian (!) */ - XM_OUT16(IoC, Port, XM_MAC_PTIME, 0xffff); - - /* Set Pause Mode in Mode Register */ - DWord |= XM_PAUSE_MODE; - - /* Set Pause Mode in MAC Rx FIFO */ - SK_OUT16(IoC, MR_ADDR(Port, RX_MFF_CTRL1), MFF_ENA_PAUSE); - } - else { - /* - * disable pause frame generation is required for 1000BT - * because the XMAC is not reset if the link is going down - */ - /* Disable Pause Mode in Mode Register */ - DWord &= ~XM_PAUSE_MODE; - - /* Disable Pause Mode in MAC Rx FIFO */ - SK_OUT16(IoC, MR_ADDR(Port, RX_MFF_CTRL1), MFF_DIS_PAUSE); - } - - XM_OUT32(IoC, Port, XM_MODE, DWord); -} /* SkXmInitPauseMd*/ - - -/****************************************************************************** - * - * SkXmInitPhyXmac() - Initialize the XMAC Phy registers - * - * Description: initializes all the XMACs Phy registers - * - * Note: - * - * Returns: - * nothing - */ -static void SkXmInitPhyXmac( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL DoLoop) /* Should a Phy LoopBack be set-up? */ -{ - SK_GEPORT *pPrt; - SK_U16 Ctrl; - - pPrt = &pAC->GIni.GP[Port]; - Ctrl = 0; - - /* Auto-negotiation ? */ - if (pPrt->PLinkMode == SK_LMODE_HALF || pPrt->PLinkMode == SK_LMODE_FULL) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("InitPhyXmac: no auto-negotiation Port %d\n", Port)); - /* Set DuplexMode in Config register */ - if (pPrt->PLinkMode == SK_LMODE_FULL) { - Ctrl |= PHY_CT_DUP_MD; - } - - /* - * Do NOT enable Auto-negotiation here. This would hold - * the link down because no IDLEs are transmitted - */ - } - else { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("InitPhyXmac: with auto-negotiation Port %d\n", Port)); - /* Set Auto-negotiation advertisement */ - - /* Set Full/half duplex capabilities */ - switch (pPrt->PLinkMode) { - case SK_LMODE_AUTOHALF: - Ctrl |= PHY_X_AN_HD; - break; - case SK_LMODE_AUTOFULL: - Ctrl |= PHY_X_AN_FD; - break; - case SK_LMODE_AUTOBOTH: - Ctrl |= PHY_X_AN_FD | PHY_X_AN_HD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E015, - SKERR_HWI_E015MSG); - } - - /* Set Flow-control capabilities */ - switch (pPrt->PFlowCtrlMode) { - case SK_FLOW_MODE_NONE: - Ctrl |= PHY_X_P_NO_PAUSE; - break; - case SK_FLOW_MODE_LOC_SEND: - Ctrl |= PHY_X_P_ASYM_MD; - break; - case SK_FLOW_MODE_SYMMETRIC: - Ctrl |= PHY_X_P_SYM_MD; - break; - case SK_FLOW_MODE_SYM_OR_REM: - Ctrl |= PHY_X_P_BOTH_MD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E016, - SKERR_HWI_E016MSG); - } - - /* Write AutoNeg Advertisement Register */ - SkXmPhyWrite(pAC, IoC, Port, PHY_XMAC_AUNE_ADV, Ctrl); - - /* Restart Auto-negotiation */ - Ctrl = PHY_CT_ANE | PHY_CT_RE_CFG; - } - - if (DoLoop) { - /* Set the Phy Loopback bit, too */ - Ctrl |= PHY_CT_LOOP; - } - - /* Write to the Phy control register */ - SkXmPhyWrite(pAC, IoC, Port, PHY_XMAC_CTRL, Ctrl); -} /* SkXmInitPhyXmac */ - - -/****************************************************************************** - * - * SkXmInitPhyBcom() - Initialize the Broadcom Phy registers - * - * Description: initializes all the Broadcom Phy registers - * - * Note: - * - * Returns: - * nothing - */ -static void SkXmInitPhyBcom( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL DoLoop) /* Should a Phy LoopBack be set-up? */ -{ - SK_GEPORT *pPrt; - SK_U16 Ctrl1; - SK_U16 Ctrl2; - SK_U16 Ctrl3; - SK_U16 Ctrl4; - SK_U16 Ctrl5; - - Ctrl1 = PHY_CT_SP1000; - Ctrl2 = 0; - Ctrl3 = PHY_SEL_TYPE; - Ctrl4 = PHY_B_PEC_EN_LTR; - Ctrl5 = PHY_B_AC_TX_TST; - - pPrt = &pAC->GIni.GP[Port]; - - /* manually Master/Slave ? */ - if (pPrt->PMSMode != SK_MS_MODE_AUTO) { - Ctrl2 |= PHY_B_1000C_MSE; - - if (pPrt->PMSMode == SK_MS_MODE_MASTER) { - Ctrl2 |= PHY_B_1000C_MSC; - } - } - /* Auto-negotiation ? */ - if (pPrt->PLinkMode == SK_LMODE_HALF || pPrt->PLinkMode == SK_LMODE_FULL) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("InitPhyBcom: no auto-negotiation Port %d\n", Port)); - /* Set DuplexMode in Config register */ - if (pPrt->PLinkMode == SK_LMODE_FULL) { - Ctrl1 |= PHY_CT_DUP_MD; - } - - /* Determine Master/Slave manually if not already done */ - if (pPrt->PMSMode == SK_MS_MODE_AUTO) { - Ctrl2 |= PHY_B_1000C_MSE; /* set it to Slave */ - } - - /* - * Do NOT enable Auto-negotiation here. This would hold - * the link down because no IDLES are transmitted - */ - } - else { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("InitPhyBcom: with auto-negotiation Port %d\n", Port)); - /* Set Auto-negotiation advertisement */ - - /* - * Workaround BCOM Errata #1 for the C5 type. - * 1000Base-T Link Acquisition Failure in Slave Mode - * Set Repeater/DTE bit 10 of the 1000Base-T Control Register - */ - Ctrl2 |= PHY_B_1000C_RD; - - /* Set Full/half duplex capabilities */ - switch (pPrt->PLinkMode) { - case SK_LMODE_AUTOHALF: - Ctrl2 |= PHY_B_1000C_AHD; - break; - case SK_LMODE_AUTOFULL: - Ctrl2 |= PHY_B_1000C_AFD; - break; - case SK_LMODE_AUTOBOTH: - Ctrl2 |= PHY_B_1000C_AFD | PHY_B_1000C_AHD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E015, - SKERR_HWI_E015MSG); - } - - /* Set Flow-control capabilities */ - switch (pPrt->PFlowCtrlMode) { - case SK_FLOW_MODE_NONE: - Ctrl3 |= PHY_B_P_NO_PAUSE; - break; - case SK_FLOW_MODE_LOC_SEND: - Ctrl3 |= PHY_B_P_ASYM_MD; - break; - case SK_FLOW_MODE_SYMMETRIC: - Ctrl3 |= PHY_B_P_SYM_MD; - break; - case SK_FLOW_MODE_SYM_OR_REM: - Ctrl3 |= PHY_B_P_BOTH_MD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E016, - SKERR_HWI_E016MSG); - } - - /* Restart Auto-negotiation */ - Ctrl1 |= PHY_CT_ANE | PHY_CT_RE_CFG; - } - - /* Initialize LED register here? */ - /* No. Please do it in SkDgXmitLed() (if required) and swap - init order of LEDs and XMAC. (MAl) */ - - /* Write 1000Base-T Control Register */ - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_1000T_CTRL, Ctrl2); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Set 1000B-T Ctrl Reg=0x%04X\n", Ctrl2)); - - /* Write AutoNeg Advertisement Register */ - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_AUNE_ADV, Ctrl3); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Set Auto-Neg.Adv.Reg=0x%04X\n", Ctrl3)); - - if (DoLoop) { - /* Set the Phy Loopback bit, too */ - Ctrl1 |= PHY_CT_LOOP; - } - - if (pAC->GIni.GIPortUsage == SK_JUMBO_LINK) { - /* configure FIFO to high latency for transmission of ext. packets */ - Ctrl4 |= PHY_B_PEC_HIGH_LA; - - /* configure reception of extended packets */ - Ctrl5 |= PHY_B_AC_LONG_PACK; - - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, Ctrl5); - } - - /* Configure LED Traffic Mode and Jumbo Frame usage if specified */ - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_P_EXT_CTRL, Ctrl4); - - /* Write to the Phy control register */ - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_CTRL, Ctrl1); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("PHY Control Reg=0x%04X\n", Ctrl1)); -} /* SkXmInitPhyBcom */ -#endif /* GENESIS */ - -#ifdef YUKON -/****************************************************************************** - * - * SkGmInitPhyMarv() - Initialize the Marvell Phy registers - * - * Description: initializes all the Marvell Phy registers - * - * Note: - * - * Returns: - * nothing - */ -static void SkGmInitPhyMarv( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL DoLoop) /* Should a Phy LoopBack be set-up? */ -{ - SK_GEPORT *pPrt; - SK_U16 PhyCtrl; - SK_U16 C1000BaseT; - SK_U16 AutoNegAdv; - SK_U16 ExtPhyCtrl; - SK_U16 LedCtrl; - SK_BOOL AutoNeg; -#if defined(SK_DIAG) || defined(DEBUG) - SK_U16 PhyStat; - SK_U16 PhyStat1; - SK_U16 PhySpecStat; -#endif /* SK_DIAG || DEBUG */ - - pPrt = &pAC->GIni.GP[Port]; - - /* Auto-negotiation ? */ - if (pPrt->PLinkMode == SK_LMODE_HALF || pPrt->PLinkMode == SK_LMODE_FULL) { - AutoNeg = SK_FALSE; - } - else { - AutoNeg = SK_TRUE; - } - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("InitPhyMarv: Port %d, auto-negotiation %s\n", - Port, AutoNeg ? "ON" : "OFF")); - -#ifdef VCPU - VCPUprintf(0, "SkGmInitPhyMarv(), Port=%u, DoLoop=%u\n", - Port, DoLoop); -#else /* VCPU */ - if (DoLoop) { - /* Set 'MAC Power up'-bit, set Manual MDI configuration */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, - PHY_M_PC_MAC_POW_UP); - } - else if (AutoNeg && pPrt->PLinkSpeed == SK_LSPEED_AUTO) { - /* Read Ext. PHY Specific Control */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_EXT_CTRL, &ExtPhyCtrl); - - ExtPhyCtrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK | - PHY_M_EC_MAC_S_MSK); - - ExtPhyCtrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ) | - PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1); - - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_EXT_CTRL, ExtPhyCtrl); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Set Ext. PHY Ctrl=0x%04X\n", ExtPhyCtrl)); - } - - /* Read PHY Control */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CTRL, &PhyCtrl); - - if (!AutoNeg) { - /* Disable Auto-negotiation */ - PhyCtrl &= ~PHY_CT_ANE; - } - - PhyCtrl |= PHY_CT_RESET; - /* Assert software reset */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_CTRL, PhyCtrl); -#endif /* VCPU */ - - PhyCtrl = 0 /* PHY_CT_COL_TST */; - C1000BaseT = 0; - AutoNegAdv = PHY_SEL_TYPE; - - /* manually Master/Slave ? */ - if (pPrt->PMSMode != SK_MS_MODE_AUTO) { - /* enable Manual Master/Slave */ - C1000BaseT |= PHY_M_1000C_MSE; - - if (pPrt->PMSMode == SK_MS_MODE_MASTER) { - C1000BaseT |= PHY_M_1000C_MSC; /* set it to Master */ - } - } - - /* Auto-negotiation ? */ - if (!AutoNeg) { - - if (pPrt->PLinkMode == SK_LMODE_FULL) { - /* Set Full Duplex Mode */ - PhyCtrl |= PHY_CT_DUP_MD; - } - - /* Set Master/Slave manually if not already done */ - if (pPrt->PMSMode == SK_MS_MODE_AUTO) { - C1000BaseT |= PHY_M_1000C_MSE; /* set it to Slave */ - } - - /* Set Speed */ - switch (pPrt->PLinkSpeed) { - case SK_LSPEED_AUTO: - case SK_LSPEED_1000MBPS: - PhyCtrl |= PHY_CT_SP1000; - break; - case SK_LSPEED_100MBPS: - PhyCtrl |= PHY_CT_SP100; - break; - case SK_LSPEED_10MBPS: - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E019, - SKERR_HWI_E019MSG); - } - - if (!DoLoop) { - PhyCtrl |= PHY_CT_RESET; - } - } - else { - /* Set Auto-negotiation advertisement */ - - if (pAC->GIni.GICopperType) { - /* Set Speed capabilities */ - switch (pPrt->PLinkSpeed) { - case SK_LSPEED_AUTO: - C1000BaseT |= PHY_M_1000C_AHD | PHY_M_1000C_AFD; - AutoNegAdv |= PHY_M_AN_100_FD | PHY_M_AN_100_HD | - PHY_M_AN_10_FD | PHY_M_AN_10_HD; - break; - case SK_LSPEED_1000MBPS: - C1000BaseT |= PHY_M_1000C_AHD | PHY_M_1000C_AFD; - break; - case SK_LSPEED_100MBPS: - AutoNegAdv |= PHY_M_AN_100_FD | PHY_M_AN_100_HD | - /* advertise 10Base-T also */ - PHY_M_AN_10_FD | PHY_M_AN_10_HD; - break; - case SK_LSPEED_10MBPS: - AutoNegAdv |= PHY_M_AN_10_FD | PHY_M_AN_10_HD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E019, - SKERR_HWI_E019MSG); - } - - /* Set Full/half duplex capabilities */ - switch (pPrt->PLinkMode) { - case SK_LMODE_AUTOHALF: - C1000BaseT &= ~PHY_M_1000C_AFD; - AutoNegAdv &= ~(PHY_M_AN_100_FD | PHY_M_AN_10_FD); - break; - case SK_LMODE_AUTOFULL: - C1000BaseT &= ~PHY_M_1000C_AHD; - AutoNegAdv &= ~(PHY_M_AN_100_HD | PHY_M_AN_10_HD); - break; - case SK_LMODE_AUTOBOTH: - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E015, - SKERR_HWI_E015MSG); - } - - /* Set Flow-control capabilities */ - switch (pPrt->PFlowCtrlMode) { - case SK_FLOW_MODE_NONE: - AutoNegAdv |= PHY_B_P_NO_PAUSE; - break; - case SK_FLOW_MODE_LOC_SEND: - AutoNegAdv |= PHY_B_P_ASYM_MD; - break; - case SK_FLOW_MODE_SYMMETRIC: - AutoNegAdv |= PHY_B_P_SYM_MD; - break; - case SK_FLOW_MODE_SYM_OR_REM: - AutoNegAdv |= PHY_B_P_BOTH_MD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E016, - SKERR_HWI_E016MSG); - } - } - else { /* special defines for FIBER (88E1011S only) */ - - /* Set Full/half duplex capabilities */ - switch (pPrt->PLinkMode) { - case SK_LMODE_AUTOHALF: - AutoNegAdv |= PHY_M_AN_1000X_AHD; - break; - case SK_LMODE_AUTOFULL: - AutoNegAdv |= PHY_M_AN_1000X_AFD; - break; - case SK_LMODE_AUTOBOTH: - AutoNegAdv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E015, - SKERR_HWI_E015MSG); - } - - /* Set Flow-control capabilities */ - switch (pPrt->PFlowCtrlMode) { - case SK_FLOW_MODE_NONE: - AutoNegAdv |= PHY_M_P_NO_PAUSE_X; - break; - case SK_FLOW_MODE_LOC_SEND: - AutoNegAdv |= PHY_M_P_ASYM_MD_X; - break; - case SK_FLOW_MODE_SYMMETRIC: - AutoNegAdv |= PHY_M_P_SYM_MD_X; - break; - case SK_FLOW_MODE_SYM_OR_REM: - AutoNegAdv |= PHY_M_P_BOTH_MD_X; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E016, - SKERR_HWI_E016MSG); - } - } - - if (!DoLoop) { - /* Restart Auto-negotiation */ - PhyCtrl |= PHY_CT_ANE | PHY_CT_RE_CFG; - } - } - -#ifdef VCPU - /* - * E-mail from Gu Lin (08-03-2002): - */ - - /* Program PHY register 30 as 16'h0708 for simulation speed up */ - SkGmPhyWrite(pAC, IoC, Port, 30, 0x0700 /* 0x0708 */); - - VCpuWait(2000); - -#else /* VCPU */ - - /* Write 1000Base-T Control Register */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_1000T_CTRL, C1000BaseT); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Set 1000B-T Ctrl =0x%04X\n", C1000BaseT)); - - /* Write AutoNeg Advertisement Register */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_AUNE_ADV, AutoNegAdv); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Set Auto-Neg.Adv.=0x%04X\n", AutoNegAdv)); -#endif /* VCPU */ - - if (DoLoop) { - /* Set the PHY Loopback bit */ - PhyCtrl |= PHY_CT_LOOP; - -#ifdef XXX - /* Program PHY register 16 as 16'h0400 to force link good */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, PHY_M_PC_FL_GOOD); -#endif /* XXX */ - -#ifndef VCPU - if (pPrt->PLinkSpeed != SK_LSPEED_AUTO) { - /* Write Ext. PHY Specific Control */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_EXT_CTRL, - (SK_U16)((pPrt->PLinkSpeed + 2) << 4)); - } -#endif /* VCPU */ - } -#ifdef TEST_ONLY - else if (pPrt->PLinkSpeed == SK_LSPEED_10MBPS) { - /* Write PHY Specific Control */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, - PHY_M_PC_EN_DET_MSK); - } -#endif - - /* Write to the PHY Control register */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_CTRL, PhyCtrl); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Set PHY Ctrl Reg.=0x%04X\n", PhyCtrl)); - -#ifdef VCPU - VCpuWait(2000); -#else - - LedCtrl = PHY_M_LED_PULS_DUR(PULS_170MS) | PHY_M_LED_BLINK_RT(BLINK_84MS); - - if ((pAC->GIni.GILedBlinkCtrl & SK_ACT_LED_BLINK) != 0) { - LedCtrl |= PHY_M_LEDC_RX_CTRL | PHY_M_LEDC_TX_CTRL; - } - - if ((pAC->GIni.GILedBlinkCtrl & SK_DUP_LED_NORMAL) != 0) { - LedCtrl |= PHY_M_LEDC_DP_CTRL; - } - - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_LED_CTRL, LedCtrl); - - if ((pAC->GIni.GILedBlinkCtrl & SK_LED_LINK100_ON) != 0) { - /* only in forced 100 Mbps mode */ - if (!AutoNeg && pPrt->PLinkSpeed == SK_LSPEED_100MBPS) { - - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_LED_OVER, - PHY_M_LED_MO_100(MO_LED_ON)); - } - } - -#ifdef SK_DIAG - c_print("Set PHY Ctrl=0x%04X\n", PhyCtrl); - c_print("Set 1000 B-T=0x%04X\n", C1000BaseT); - c_print("Set Auto-Neg=0x%04X\n", AutoNegAdv); - c_print("Set Ext Ctrl=0x%04X\n", ExtPhyCtrl); -#endif /* SK_DIAG */ - -#if defined(SK_DIAG) || defined(DEBUG) - /* Read PHY Control */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CTRL, &PhyCtrl); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("PHY Ctrl Reg.=0x%04X\n", PhyCtrl)); - - /* Read 1000Base-T Control Register */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_1000T_CTRL, &C1000BaseT); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("1000B-T Ctrl =0x%04X\n", C1000BaseT)); - - /* Read AutoNeg Advertisement Register */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_AUNE_ADV, &AutoNegAdv); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Auto-Neg.Adv.=0x%04X\n", AutoNegAdv)); - - /* Read Ext. PHY Specific Control */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_EXT_CTRL, &ExtPhyCtrl); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Ext. PHY Ctrl=0x%04X\n", ExtPhyCtrl)); - - /* Read PHY Status */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_STAT, &PhyStat); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("PHY Stat Reg.=0x%04X\n", PhyStat)); - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_STAT, &PhyStat1); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("PHY Stat Reg.=0x%04X\n", PhyStat1)); - - /* Read PHY Specific Status */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_STAT, &PhySpecStat); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("PHY Spec Stat=0x%04X\n", PhySpecStat)); -#endif /* SK_DIAG || DEBUG */ - -#ifdef SK_DIAG - c_print("PHY Ctrl Reg=0x%04X\n", PhyCtrl); - c_print("PHY 1000 Reg=0x%04X\n", C1000BaseT); - c_print("PHY AnAd Reg=0x%04X\n", AutoNegAdv); - c_print("Ext Ctrl Reg=0x%04X\n", ExtPhyCtrl); - c_print("PHY Stat Reg=0x%04X\n", PhyStat); - c_print("PHY Stat Reg=0x%04X\n", PhyStat1); - c_print("PHY Spec Reg=0x%04X\n", PhySpecStat); -#endif /* SK_DIAG */ - -#endif /* VCPU */ - -} /* SkGmInitPhyMarv */ -#endif /* YUKON */ - - -#ifdef OTHER_PHY -/****************************************************************************** - * - * SkXmInitPhyLone() - Initialize the Level One Phy registers - * - * Description: initializes all the Level One Phy registers - * - * Note: - * - * Returns: - * nothing - */ -static void SkXmInitPhyLone( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL DoLoop) /* Should a Phy LoopBack be set-up? */ -{ - SK_GEPORT *pPrt; - SK_U16 Ctrl1; - SK_U16 Ctrl2; - SK_U16 Ctrl3; - - Ctrl1 = PHY_CT_SP1000; - Ctrl2 = 0; - Ctrl3 = PHY_SEL_TYPE; - - pPrt = &pAC->GIni.GP[Port]; - - /* manually Master/Slave ? */ - if (pPrt->PMSMode != SK_MS_MODE_AUTO) { - Ctrl2 |= PHY_L_1000C_MSE; - - if (pPrt->PMSMode == SK_MS_MODE_MASTER) { - Ctrl2 |= PHY_L_1000C_MSC; - } - } - /* Auto-negotiation ? */ - if (pPrt->PLinkMode == SK_LMODE_HALF || pPrt->PLinkMode == SK_LMODE_FULL) { - /* - * level one spec say: "1000 Mbps: manual mode not allowed" - * but lets see what happens... - */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("InitPhyLone: no auto-negotiation Port %d\n", Port)); - /* Set DuplexMode in Config register */ - if (pPrt->PLinkMode == SK_LMODE_FULL) { - Ctrl1 |= PHY_CT_DUP_MD; - } - - /* Determine Master/Slave manually if not already done */ - if (pPrt->PMSMode == SK_MS_MODE_AUTO) { - Ctrl2 |= PHY_L_1000C_MSE; /* set it to Slave */ - } - - /* - * Do NOT enable Auto-negotiation here. This would hold - * the link down because no IDLES are transmitted - */ - } - else { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("InitPhyLone: with auto-negotiation Port %d\n", Port)); - /* Set Auto-negotiation advertisement */ - - /* Set Full/half duplex capabilities */ - switch (pPrt->PLinkMode) { - case SK_LMODE_AUTOHALF: - Ctrl2 |= PHY_L_1000C_AHD; - break; - case SK_LMODE_AUTOFULL: - Ctrl2 |= PHY_L_1000C_AFD; - break; - case SK_LMODE_AUTOBOTH: - Ctrl2 |= PHY_L_1000C_AFD | PHY_L_1000C_AHD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E015, - SKERR_HWI_E015MSG); - } - - /* Set Flow-control capabilities */ - switch (pPrt->PFlowCtrlMode) { - case SK_FLOW_MODE_NONE: - Ctrl3 |= PHY_L_P_NO_PAUSE; - break; - case SK_FLOW_MODE_LOC_SEND: - Ctrl3 |= PHY_L_P_ASYM_MD; - break; - case SK_FLOW_MODE_SYMMETRIC: - Ctrl3 |= PHY_L_P_SYM_MD; - break; - case SK_FLOW_MODE_SYM_OR_REM: - Ctrl3 |= PHY_L_P_BOTH_MD; - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E016, - SKERR_HWI_E016MSG); - } - - /* Restart Auto-negotiation */ - Ctrl1 = PHY_CT_ANE | PHY_CT_RE_CFG; - } - - /* Write 1000Base-T Control Register */ - SkXmPhyWrite(pAC, IoC, Port, PHY_LONE_1000T_CTRL, Ctrl2); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("1000B-T Ctrl Reg=0x%04X\n", Ctrl2)); - - /* Write AutoNeg Advertisement Register */ - SkXmPhyWrite(pAC, IoC, Port, PHY_LONE_AUNE_ADV, Ctrl3); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Auto-Neg.Adv.Reg=0x%04X\n", Ctrl3)); - - if (DoLoop) { - /* Set the Phy Loopback bit, too */ - Ctrl1 |= PHY_CT_LOOP; - } - - /* Write to the Phy control register */ - SkXmPhyWrite(pAC, IoC, Port, PHY_LONE_CTRL, Ctrl1); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("PHY Control Reg=0x%04X\n", Ctrl1)); -} /* SkXmInitPhyLone */ - - -/****************************************************************************** - * - * SkXmInitPhyNat() - Initialize the National Phy registers - * - * Description: initializes all the National Phy registers - * - * Note: - * - * Returns: - * nothing - */ -static void SkXmInitPhyNat( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL DoLoop) /* Should a Phy LoopBack be set-up? */ -{ -/* todo: National */ -} /* SkXmInitPhyNat */ -#endif /* OTHER_PHY */ - - -/****************************************************************************** - * - * SkMacInitPhy() - Initialize the PHY registers - * - * Description: calls the Init PHY routines dep. on board type - * - * Note: - * - * Returns: - * nothing - */ -void SkMacInitPhy( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL DoLoop) /* Should a Phy LoopBack be set-up? */ -{ - SK_GEPORT *pPrt; - - pPrt = &pAC->GIni.GP[Port]; - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - switch (pPrt->PhyType) { - case SK_PHY_XMAC: - SkXmInitPhyXmac(pAC, IoC, Port, DoLoop); - break; - case SK_PHY_BCOM: - SkXmInitPhyBcom(pAC, IoC, Port, DoLoop); - break; -#ifdef OTHER_PHY - case SK_PHY_LONE: - SkXmInitPhyLone(pAC, IoC, Port, DoLoop); - break; - case SK_PHY_NAT: - SkXmInitPhyNat(pAC, IoC, Port, DoLoop); - break; -#endif /* OTHER_PHY */ - } - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - SkGmInitPhyMarv(pAC, IoC, Port, DoLoop); - } -#endif /* YUKON */ - -} /* SkMacInitPhy */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmAutoNegDoneXmac() - Auto-negotiation handling - * - * Description: - * This function handles the auto-negotiation if the Done bit is set. - * - * Returns: - * SK_AND_OK o.k. - * SK_AND_DUP_CAP Duplex capability error happened - * SK_AND_OTHER Other error happened - */ -static int SkXmAutoNegDoneXmac( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U16 ResAb; /* Resolved Ability */ - SK_U16 LPAb; /* Link Partner Ability */ - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegDoneXmac, Port %d\n", Port)); - - pPrt = &pAC->GIni.GP[Port]; - - /* Get PHY parameters */ - SkXmPhyRead(pAC, IoC, Port, PHY_XMAC_AUNE_LP, &LPAb); - SkXmPhyRead(pAC, IoC, Port, PHY_XMAC_RES_ABI, &ResAb); - - if ((LPAb & PHY_X_AN_RFB) != 0) { - /* At least one of the remote fault bit is set */ - /* Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegFail: Remote fault bit set Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - return(SK_AND_OTHER); - } - - /* Check Duplex mismatch */ - if ((ResAb & (PHY_X_RS_HD | PHY_X_RS_FD)) == PHY_X_RS_FD) { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_AUTOFULL; - } - else if ((ResAb & (PHY_X_RS_HD | PHY_X_RS_FD)) == PHY_X_RS_HD) { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_AUTOHALF; - } - else { - /* Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegFail: Duplex mode mismatch Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - return(SK_AND_DUP_CAP); - } - - /* Check PAUSE mismatch */ - /* We are NOT using chapter 4.23 of the Xaqti manual */ - /* We are using IEEE 802.3z/D5.0 Table 37-4 */ - if ((pPrt->PFlowCtrlMode == SK_FLOW_MODE_SYMMETRIC || - pPrt->PFlowCtrlMode == SK_FLOW_MODE_SYM_OR_REM) && - (LPAb & PHY_X_P_SYM_MD) != 0) { - /* Symmetric PAUSE */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_SYMMETRIC; - } - else if (pPrt->PFlowCtrlMode == SK_FLOW_MODE_SYM_OR_REM && - (LPAb & PHY_X_RS_PAUSE) == PHY_X_P_ASYM_MD) { - /* Enable PAUSE receive, disable PAUSE transmit */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_REM_SEND; - } - else if (pPrt->PFlowCtrlMode == SK_FLOW_MODE_LOC_SEND && - (LPAb & PHY_X_RS_PAUSE) == PHY_X_P_BOTH_MD) { - /* Disable PAUSE receive, enable PAUSE transmit */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_LOC_SEND; - } - else { - /* PAUSE mismatch -> no PAUSE */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_NONE; - } - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_1000MBPS; - - return(SK_AND_OK); -} /* SkXmAutoNegDoneXmac */ - - -/****************************************************************************** - * - * SkXmAutoNegDoneBcom() - Auto-negotiation handling - * - * Description: - * This function handles the auto-negotiation if the Done bit is set. - * - * Returns: - * SK_AND_OK o.k. - * SK_AND_DUP_CAP Duplex capability error happened - * SK_AND_OTHER Other error happened - */ -static int SkXmAutoNegDoneBcom( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U16 LPAb; /* Link Partner Ability */ - SK_U16 AuxStat; /* Auxiliary Status */ - -#ifdef TEST_ONLY -01-Sep-2000 RA;:;: - SK_U16 ResAb; /* Resolved Ability */ -#endif /* 0 */ - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegDoneBcom, Port %d\n", Port)); - pPrt = &pAC->GIni.GP[Port]; - - /* Get PHY parameters */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUNE_LP, &LPAb); -#ifdef TEST_ONLY -01-Sep-2000 RA;:;: - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_1000T_STAT, &ResAb); -#endif /* 0 */ - - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUX_STAT, &AuxStat); - - if ((LPAb & PHY_B_AN_RF) != 0) { - /* Remote fault bit is set: Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegFail: Remote fault bit set Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - return(SK_AND_OTHER); - } - - /* Check Duplex mismatch */ - if ((AuxStat & PHY_B_AS_AN_RES_MSK) == PHY_B_RES_1000FD) { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_AUTOFULL; - } - else if ((AuxStat & PHY_B_AS_AN_RES_MSK) == PHY_B_RES_1000HD) { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_AUTOHALF; - } - else { - /* Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegFail: Duplex mode mismatch Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - return(SK_AND_DUP_CAP); - } - -#ifdef TEST_ONLY -01-Sep-2000 RA;:;: - /* Check Master/Slave resolution */ - if ((ResAb & PHY_B_1000S_MSF) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Master/Slave Fault Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - pPrt->PMSStatus = SK_MS_STAT_FAULT; - return(SK_AND_OTHER); - } - - pPrt->PMSStatus = ((ResAb & PHY_B_1000S_MSR) != 0) ? - SK_MS_STAT_MASTER : SK_MS_STAT_SLAVE; -#endif /* 0 */ - - /* Check PAUSE mismatch ??? */ - /* We are using IEEE 802.3z/D5.0 Table 37-4 */ - if ((AuxStat & PHY_B_AS_PAUSE_MSK) == PHY_B_AS_PAUSE_MSK) { - /* Symmetric PAUSE */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_SYMMETRIC; - } - else if ((AuxStat & PHY_B_AS_PAUSE_MSK) == PHY_B_AS_PRR) { - /* Enable PAUSE receive, disable PAUSE transmit */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_REM_SEND; - } - else if ((AuxStat & PHY_B_AS_PAUSE_MSK) == PHY_B_AS_PRT) { - /* Disable PAUSE receive, enable PAUSE transmit */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_LOC_SEND; - } - else { - /* PAUSE mismatch -> no PAUSE */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_NONE; - } - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_1000MBPS; - - return(SK_AND_OK); -} /* SkXmAutoNegDoneBcom */ -#endif /* GENESIS */ - - -#ifdef YUKON -/****************************************************************************** - * - * SkGmAutoNegDoneMarv() - Auto-negotiation handling - * - * Description: - * This function handles the auto-negotiation if the Done bit is set. - * - * Returns: - * SK_AND_OK o.k. - * SK_AND_DUP_CAP Duplex capability error happened - * SK_AND_OTHER Other error happened - */ -static int SkGmAutoNegDoneMarv( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U16 LPAb; /* Link Partner Ability */ - SK_U16 ResAb; /* Resolved Ability */ - SK_U16 AuxStat; /* Auxiliary Status */ - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegDoneMarv, Port %d\n", Port)); - pPrt = &pAC->GIni.GP[Port]; - - /* Get PHY parameters */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_AUNE_LP, &LPAb); - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Link P.Abil.=0x%04X\n", LPAb)); - - if ((LPAb & PHY_M_AN_RF) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegFail: Remote fault bit set Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - return(SK_AND_OTHER); - } - - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_1000T_STAT, &ResAb); - - /* Check Master/Slave resolution */ - if ((ResAb & PHY_B_1000S_MSF) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Master/Slave Fault Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - pPrt->PMSStatus = SK_MS_STAT_FAULT; - return(SK_AND_OTHER); - } - - pPrt->PMSStatus = ((ResAb & PHY_B_1000S_MSR) != 0) ? - (SK_U8)SK_MS_STAT_MASTER : (SK_U8)SK_MS_STAT_SLAVE; - - /* Read PHY Specific Status */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_STAT, &AuxStat); - - /* Check Speed & Duplex resolved */ - if ((AuxStat & PHY_M_PS_SPDUP_RES) == 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegFail: Speed & Duplex not resolved, Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_UNKNOWN; - return(SK_AND_DUP_CAP); - } - - if ((AuxStat & PHY_M_PS_FULL_DUP) != 0) { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_AUTOFULL; - } - else { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_AUTOHALF; - } - - /* Check PAUSE mismatch ??? */ - /* We are using IEEE 802.3z/D5.0 Table 37-4 */ - if ((AuxStat & PHY_M_PS_PAUSE_MSK) == PHY_M_PS_PAUSE_MSK) { - /* Symmetric PAUSE */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_SYMMETRIC; - } - else if ((AuxStat & PHY_M_PS_PAUSE_MSK) == PHY_M_PS_RX_P_EN) { - /* Enable PAUSE receive, disable PAUSE transmit */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_REM_SEND; - } - else if ((AuxStat & PHY_M_PS_PAUSE_MSK) == PHY_M_PS_TX_P_EN) { - /* Disable PAUSE receive, enable PAUSE transmit */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_LOC_SEND; - } - else { - /* PAUSE mismatch -> no PAUSE */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_NONE; - } - - /* set used link speed */ - switch ((unsigned)(AuxStat & PHY_M_PS_SPEED_MSK)) { - case (unsigned)PHY_M_PS_SPEED_1000: - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_1000MBPS; - break; - case PHY_M_PS_SPEED_100: - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_100MBPS; - break; - default: - pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_10MBPS; - } - - return(SK_AND_OK); -} /* SkGmAutoNegDoneMarv */ -#endif /* YUKON */ - - -#ifdef OTHER_PHY -/****************************************************************************** - * - * SkXmAutoNegDoneLone() - Auto-negotiation handling - * - * Description: - * This function handles the auto-negotiation if the Done bit is set. - * - * Returns: - * SK_AND_OK o.k. - * SK_AND_DUP_CAP Duplex capability error happened - * SK_AND_OTHER Other error happened - */ -static int SkXmAutoNegDoneLone( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U16 ResAb; /* Resolved Ability */ - SK_U16 LPAb; /* Link Partner Ability */ - SK_U16 QuickStat; /* Auxiliary Status */ - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegDoneLone, Port %d\n", Port)); - pPrt = &pAC->GIni.GP[Port]; - - /* Get PHY parameters */ - SkXmPhyRead(pAC, IoC, Port, PHY_LONE_AUNE_LP, &LPAb); - SkXmPhyRead(pAC, IoC, Port, PHY_LONE_1000T_STAT, &ResAb); - SkXmPhyRead(pAC, IoC, Port, PHY_LONE_Q_STAT, &QuickStat); - - if ((LPAb & PHY_L_AN_RF) != 0) { - /* Remote fault bit is set */ - /* Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegFail: Remote fault bit set Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - return(SK_AND_OTHER); - } - - /* Check Duplex mismatch */ - if ((QuickStat & PHY_L_QS_DUP_MOD) != 0) { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_AUTOFULL; - } - else { - pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_AUTOHALF; - } - - /* Check Master/Slave resolution */ - if ((ResAb & PHY_L_1000S_MSF) != 0) { - /* Error */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("Master/Slave Fault Port %d\n", Port)); - pPrt->PAutoNegFail = SK_TRUE; - pPrt->PMSStatus = SK_MS_STAT_FAULT; - return(SK_AND_OTHER); - } - else if (ResAb & PHY_L_1000S_MSR) { - pPrt->PMSStatus = SK_MS_STAT_MASTER; - } - else { - pPrt->PMSStatus = SK_MS_STAT_SLAVE; - } - - /* Check PAUSE mismatch */ - /* We are using IEEE 802.3z/D5.0 Table 37-4 */ - /* we must manually resolve the abilities here */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_NONE; - - switch (pPrt->PFlowCtrlMode) { - case SK_FLOW_MODE_NONE: - /* default */ - break; - case SK_FLOW_MODE_LOC_SEND: - if ((QuickStat & (PHY_L_QS_PAUSE | PHY_L_QS_AS_PAUSE)) == - (PHY_L_QS_PAUSE | PHY_L_QS_AS_PAUSE)) { - /* Disable PAUSE receive, enable PAUSE transmit */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_LOC_SEND; - } - break; - case SK_FLOW_MODE_SYMMETRIC: - if ((QuickStat & PHY_L_QS_PAUSE) != 0) { - /* Symmetric PAUSE */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_SYMMETRIC; - } - break; - case SK_FLOW_MODE_SYM_OR_REM: - if ((QuickStat & (PHY_L_QS_PAUSE | PHY_L_QS_AS_PAUSE)) == - PHY_L_QS_AS_PAUSE) { - /* Enable PAUSE receive, disable PAUSE transmit */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_REM_SEND; - } - else if ((QuickStat & PHY_L_QS_PAUSE) != 0) { - /* Symmetric PAUSE */ - pPrt->PFlowCtrlStatus = SK_FLOW_STAT_SYMMETRIC; - } - break; - default: - SK_ERR_LOG(pAC, SK_ERRCL_SW | SK_ERRCL_INIT, SKERR_HWI_E016, - SKERR_HWI_E016MSG); - } - - return(SK_AND_OK); -} /* SkXmAutoNegDoneLone */ - - -/****************************************************************************** - * - * SkXmAutoNegDoneNat() - Auto-negotiation handling - * - * Description: - * This function handles the auto-negotiation if the Done bit is set. - * - * Returns: - * SK_AND_OK o.k. - * SK_AND_DUP_CAP Duplex capability error happened - * SK_AND_OTHER Other error happened - */ -static int SkXmAutoNegDoneNat( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ -/* todo: National */ - return(SK_AND_OK); -} /* SkXmAutoNegDoneNat */ -#endif /* OTHER_PHY */ - - -/****************************************************************************** - * - * SkMacAutoNegDone() - Auto-negotiation handling - * - * Description: calls the auto-negotiation done routines dep. on board type - * - * Returns: - * SK_AND_OK o.k. - * SK_AND_DUP_CAP Duplex capability error happened - * SK_AND_OTHER Other error happened - */ -int SkMacAutoNegDone( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - int Rtv; - - Rtv = SK_AND_OK; - - pPrt = &pAC->GIni.GP[Port]; - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - switch (pPrt->PhyType) { - - case SK_PHY_XMAC: - Rtv = SkXmAutoNegDoneXmac(pAC, IoC, Port); - break; - case SK_PHY_BCOM: - Rtv = SkXmAutoNegDoneBcom(pAC, IoC, Port); - break; -#ifdef OTHER_PHY - case SK_PHY_LONE: - Rtv = SkXmAutoNegDoneLone(pAC, IoC, Port); - break; - case SK_PHY_NAT: - Rtv = SkXmAutoNegDoneNat(pAC, IoC, Port); - break; -#endif /* OTHER_PHY */ - default: - return(SK_AND_OTHER); - } - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - Rtv = SkGmAutoNegDoneMarv(pAC, IoC, Port); - } -#endif /* YUKON */ - - if (Rtv != SK_AND_OK) { - return(Rtv); - } - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNeg done Port %d\n", Port)); - - /* We checked everything and may now enable the link */ - pPrt->PAutoNegFail = SK_FALSE; - - SkMacRxTxEnable(pAC, IoC, Port); - - return(SK_AND_OK); -} /* SkMacAutoNegDone */ - - -/****************************************************************************** - * - * SkMacRxTxEnable() - Enable Rx/Tx activity if port is up - * - * Description: enables Rx/Tx dep. on board type - * - * Returns: - * 0 o.k. - * != 0 Error happened - */ -int SkMacRxTxEnable( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U16 Reg; /* 16-bit register value */ - SK_U16 IntMask; /* MAC interrupt mask */ -#ifdef GENESIS - SK_U16 SWord; -#endif - - pPrt = &pAC->GIni.GP[Port]; - - if (!pPrt->PHWLinkUp) { - /* The Hardware link is NOT up */ - return(0); - } - - if ((pPrt->PLinkMode == SK_LMODE_AUTOHALF || - pPrt->PLinkMode == SK_LMODE_AUTOFULL || - pPrt->PLinkMode == SK_LMODE_AUTOBOTH) && - pPrt->PAutoNegFail) { - /* Auto-negotiation is not done or failed */ - return(0); - } - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* set Duplex Mode and Pause Mode */ - SkXmInitDupMd(pAC, IoC, Port); - - SkXmInitPauseMd(pAC, IoC, Port); - - /* - * Initialize the Interrupt Mask Register. Default IRQs are... - * - Link Asynchronous Event - * - Link Partner requests config - * - Auto Negotiation Done - * - Rx Counter Event Overflow - * - Tx Counter Event Overflow - * - Transmit FIFO Underrun - */ - IntMask = XM_DEF_MSK; - -#ifdef DEBUG - /* add IRQ for Receive FIFO Overflow */ - IntMask &= ~XM_IS_RXF_OV; -#endif /* DEBUG */ - - if (pPrt->PhyType != SK_PHY_XMAC) { - /* disable GP0 interrupt bit */ - IntMask |= XM_IS_INP_ASS; - } - XM_OUT16(IoC, Port, XM_IMSK, IntMask); - - /* get MMU Command Reg. */ - XM_IN16(IoC, Port, XM_MMU_CMD, &Reg); - - if (pPrt->PhyType != SK_PHY_XMAC && - (pPrt->PLinkModeStatus == SK_LMODE_STAT_FULL || - pPrt->PLinkModeStatus == SK_LMODE_STAT_AUTOFULL)) { - /* set to Full Duplex */ - Reg |= XM_MMU_GMII_FD; - } - - switch (pPrt->PhyType) { - case SK_PHY_BCOM: - /* - * Workaround BCOM Errata (#10523) for all BCom Phys - * Enable Power Management after link up - */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, &SWord); - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, - (SK_U16)(SWord & ~PHY_B_AC_DIS_PM)); - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_INT_MASK, - (SK_U16)PHY_B_DEF_MSK); - break; -#ifdef OTHER_PHY - case SK_PHY_LONE: - SkXmPhyWrite(pAC, IoC, Port, PHY_LONE_INT_ENAB, PHY_L_DEF_MSK); - break; - case SK_PHY_NAT: - /* todo National: - SkXmPhyWrite(pAC, IoC, Port, PHY_NAT_INT_MASK, PHY_N_DEF_MSK); */ - /* no interrupts possible from National ??? */ - break; -#endif /* OTHER_PHY */ - } - - /* enable Rx/Tx */ - XM_OUT16(IoC, Port, XM_MMU_CMD, Reg | XM_MMU_ENA_RX | XM_MMU_ENA_TX); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* - * Initialize the Interrupt Mask Register. Default IRQs are... - * - Rx Counter Event Overflow - * - Tx Counter Event Overflow - * - Transmit FIFO Underrun - */ - IntMask = GMAC_DEF_MSK; - -#ifdef DEBUG - /* add IRQ for Receive FIFO Overrun */ - IntMask |= GM_IS_RX_FF_OR; -#endif /* DEBUG */ - - SK_OUT8(IoC, GMAC_IRQ_MSK, (SK_U8)IntMask); - - /* get General Purpose Control */ - GM_IN16(IoC, Port, GM_GP_CTRL, &Reg); - - if (pPrt->PLinkModeStatus == SK_LMODE_STAT_FULL || - pPrt->PLinkModeStatus == SK_LMODE_STAT_AUTOFULL) { - /* set to Full Duplex */ - Reg |= GM_GPCR_DUP_FULL; - } - - /* enable Rx/Tx */ - GM_OUT16(IoC, Port, GM_GP_CTRL, (SK_U16)(Reg | GM_GPCR_RX_ENA | - GM_GPCR_TX_ENA)); - -#ifndef VCPU - /* Enable all PHY interrupts */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_INT_MASK, - (SK_U16)PHY_M_DEF_MSK); -#endif /* VCPU */ - } -#endif /* YUKON */ - - return(0); - -} /* SkMacRxTxEnable */ - - -/****************************************************************************** - * - * SkMacRxTxDisable() - Disable Receiver and Transmitter - * - * Description: disables Rx/Tx dep. on board type - * - * Returns: N/A - */ -void SkMacRxTxDisable( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U16 Word; - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - XM_IN16(IoC, Port, XM_MMU_CMD, &Word); - - XM_OUT16(IoC, Port, XM_MMU_CMD, Word & ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX)); - - /* dummy read to ensure writing */ - XM_IN16(IoC, Port, XM_MMU_CMD, &Word); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - - GM_IN16(IoC, Port, GM_GP_CTRL, &Word); - - GM_OUT16(IoC, Port, GM_GP_CTRL, (SK_U16)(Word & ~(GM_GPCR_RX_ENA | - GM_GPCR_TX_ENA))); - - /* dummy read to ensure writing */ - GM_IN16(IoC, Port, GM_GP_CTRL, &Word); - } -#endif /* YUKON */ - -} /* SkMacRxTxDisable */ - - -/****************************************************************************** - * - * SkMacIrqDisable() - Disable IRQ from MAC - * - * Description: sets the IRQ-mask to disable IRQ dep. on board type - * - * Returns: N/A - */ -void SkMacIrqDisable( -SK_AC *pAC, /* Adapter Context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; -#ifdef GENESIS - SK_U16 Word; -#endif - - pPrt = &pAC->GIni.GP[Port]; - -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - - /* disable all XMAC IRQs */ - XM_OUT16(IoC, Port, XM_IMSK, 0xffff); - - /* Disable all PHY interrupts */ - switch (pPrt->PhyType) { - case SK_PHY_BCOM: - /* Make sure that PHY is initialized */ - if (pPrt->PState != SK_PRT_RESET) { - /* NOT allowed if BCOM is in RESET state */ - /* Workaround BCOM Errata (#10523) all BCom */ - /* Disable Power Management if link is down */ - SkXmPhyRead(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, &Word); - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_AUX_CTRL, - (SK_U16)(Word | PHY_B_AC_DIS_PM)); - SkXmPhyWrite(pAC, IoC, Port, PHY_BCOM_INT_MASK, 0xffff); - } - break; -#ifdef OTHER_PHY - case SK_PHY_LONE: - SkXmPhyWrite(pAC, IoC, Port, PHY_LONE_INT_ENAB, 0); - break; - case SK_PHY_NAT: - /* todo: National - SkXmPhyWrite(pAC, IoC, Port, PHY_NAT_INT_MASK, 0xffff); */ - break; -#endif /* OTHER_PHY */ - } - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* disable all GMAC IRQs */ - SK_OUT8(IoC, GMAC_IRQ_MSK, 0); - -#ifndef VCPU - /* Disable all PHY interrupts */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_INT_MASK, 0); -#endif /* VCPU */ - } -#endif /* YUKON */ - -} /* SkMacIrqDisable */ - - -#ifdef SK_DIAG -/****************************************************************************** - * - * SkXmSendCont() - Enable / Disable Send Continuous Mode - * - * Description: enable / disable Send Continuous Mode on XMAC - * - * Returns: - * nothing - */ -void SkXmSendCont( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL Enable) /* Enable / Disable */ -{ - SK_U32 MdReg; - - XM_IN32(IoC, Port, XM_MODE, &MdReg); - - if (Enable) { - MdReg |= XM_MD_TX_CONT; - } - else { - MdReg &= ~XM_MD_TX_CONT; - } - /* setup Mode Register */ - XM_OUT32(IoC, Port, XM_MODE, MdReg); - -} /* SkXmSendCont */ - - -/****************************************************************************** - * - * SkMacTimeStamp() - Enable / Disable Time Stamp - * - * Description: enable / disable Time Stamp generation for Rx packets - * - * Returns: - * nothing - */ -void SkMacTimeStamp( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL Enable) /* Enable / Disable */ -{ - SK_U32 MdReg; - SK_U8 TimeCtrl; - - if (pAC->GIni.GIGenesis) { - - XM_IN32(IoC, Port, XM_MODE, &MdReg); - - if (Enable) { - MdReg |= XM_MD_ATS; - } - else { - MdReg &= ~XM_MD_ATS; - } - /* setup Mode Register */ - XM_OUT32(IoC, Port, XM_MODE, MdReg); - } - else { - if (Enable) { - TimeCtrl = GMT_ST_START | GMT_ST_CLR_IRQ; - } - else { - TimeCtrl = GMT_ST_STOP | GMT_ST_CLR_IRQ; - } - /* Start/Stop Time Stamp Timer */ - SK_OUT8(IoC, GMAC_TI_ST_CTRL, TimeCtrl); - } - -} /* SkMacTimeStamp*/ - -#else /* !SK_DIAG */ - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmAutoNegLipaXmac() - Decides whether Link Partner could do auto-neg - * - * This function analyses the Interrupt status word. If any of the - * Auto-negotiating interrupt bits are set, the PLipaAutoNeg variable - * is set true. - */ -void SkXmAutoNegLipaXmac( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_U16 IStatus) /* Interrupt Status word to analyse */ -{ - SK_GEPORT *pPrt; - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PLipaAutoNeg != SK_LIPA_AUTO && - (IStatus & (XM_IS_LIPA_RC | XM_IS_RX_PAGE | XM_IS_AND)) != 0) { - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegLipa: AutoNeg detected on Port %d, IStatus=0x%04X\n", - Port, IStatus)); - pPrt->PLipaAutoNeg = SK_LIPA_AUTO; - } -} /* SkXmAutoNegLipaXmac */ -#endif /* GENESIS */ - - -/****************************************************************************** - * - * SkMacAutoNegLipaPhy() - Decides whether Link Partner could do auto-neg - * - * This function analyses the PHY status word. - * If any of the Auto-negotiating bits are set, the PLipaAutoNeg variable - * is set true. - */ -void SkMacAutoNegLipaPhy( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_U16 PhyStat) /* PHY Status word to analyse */ -{ - SK_GEPORT *pPrt; - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PLipaAutoNeg != SK_LIPA_AUTO && - (PhyStat & PHY_ST_AN_OVER) != 0) { - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("AutoNegLipa: AutoNeg detected on Port %d, PhyStat=0x%04X\n", - Port, PhyStat)); - pPrt->PLipaAutoNeg = SK_LIPA_AUTO; - } -} /* SkMacAutoNegLipaPhy */ - - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmIrq() - Interrupt Service Routine - * - * Description: services an Interrupt Request of the XMAC - * - * Note: - * With an external PHY, some interrupt bits are not meaningfull any more: - * - LinkAsyncEvent (bit #14) XM_IS_LNK_AE - * - LinkPartnerReqConfig (bit #10) XM_IS_LIPA_RC - * - Page Received (bit #9) XM_IS_RX_PAGE - * - NextPageLoadedForXmt (bit #8) XM_IS_TX_PAGE - * - AutoNegDone (bit #7) XM_IS_AND - * Also probably not valid any more is the GP0 input bit: - * - GPRegisterBit0set XM_IS_INP_ASS - * - * Returns: - * nothing - */ -static void SkXmIrq( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_EVPARA Para; - SK_U16 IStatus; /* Interrupt status read from the XMAC */ - SK_U16 IStatus2; -#ifdef SK_SLIM - SK_U64 OverflowStatus; -#endif - - pPrt = &pAC->GIni.GP[Port]; - - XM_IN16(IoC, Port, XM_ISRC, &IStatus); - - /* LinkPartner Auto-negable? */ - if (pPrt->PhyType == SK_PHY_XMAC) { - SkXmAutoNegLipaXmac(pAC, IoC, Port, IStatus); - } - else { - /* mask bits that are not used with ext. PHY */ - IStatus &= ~(XM_IS_LNK_AE | XM_IS_LIPA_RC | - XM_IS_RX_PAGE | XM_IS_TX_PAGE | - XM_IS_AND | XM_IS_INP_ASS); - } - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("XmacIrq Port %d Isr 0x%04X\n", Port, IStatus)); - - if (!pPrt->PHWLinkUp) { - /* Spurious XMAC interrupt */ - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("SkXmIrq: spurious interrupt on Port %d\n", Port)); - return; - } - - if ((IStatus & XM_IS_INP_ASS) != 0) { - /* Reread ISR Register if link is not in sync */ - XM_IN16(IoC, Port, XM_ISRC, &IStatus2); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("SkXmIrq: Link async. Double check Port %d 0x%04X 0x%04X\n", - Port, IStatus, IStatus2)); - IStatus &= ~XM_IS_INP_ASS; - IStatus |= IStatus2; - } - - if ((IStatus & XM_IS_LNK_AE) != 0) { - /* not used, GP0 is used instead */ - } - - if ((IStatus & XM_IS_TX_ABORT) != 0) { - /* not used */ - } - - if ((IStatus & XM_IS_FRC_INT) != 0) { - /* not used, use ASIC IRQ instead if needed */ - } - - if ((IStatus & (XM_IS_INP_ASS | XM_IS_LIPA_RC | XM_IS_RX_PAGE)) != 0) { - SkHWLinkDown(pAC, IoC, Port); - - /* Signal to RLMT */ - Para.Para32[0] = (SK_U32)Port; - SkEventQueue(pAC, SKGE_RLMT, SK_RLMT_LINK_DOWN, Para); - - /* Start workaround Errata #2 timer */ - SkTimerStart(pAC, IoC, &pPrt->PWaTimer, SK_WA_INA_TIME, - SKGE_HWAC, SK_HWEV_WATIM, Para); - } - - if ((IStatus & XM_IS_RX_PAGE) != 0) { - /* not used */ - } - - if ((IStatus & XM_IS_TX_PAGE) != 0) { - /* not used */ - } - - if ((IStatus & XM_IS_AND) != 0) { - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("SkXmIrq: AND on link that is up Port %d\n", Port)); - } - - if ((IStatus & XM_IS_TSC_OV) != 0) { - /* not used */ - } - - /* Combined Tx & Rx Counter Overflow SIRQ Event */ - if ((IStatus & (XM_IS_RXC_OV | XM_IS_TXC_OV)) != 0) { -#ifdef SK_SLIM - SkXmOverflowStatus(pAC, IoC, Port, IStatus, &OverflowStatus); -#else - Para.Para32[0] = (SK_U32)Port; - Para.Para32[1] = (SK_U32)IStatus; - SkPnmiEvent(pAC, IoC, SK_PNMI_EVT_SIRQ_OVERFLOW, Para); -#endif /* SK_SLIM */ - } - - if ((IStatus & XM_IS_RXF_OV) != 0) { - /* normal situation -> no effect */ -#ifdef DEBUG - pPrt->PRxOverCnt++; -#endif /* DEBUG */ - } - - if ((IStatus & XM_IS_TXF_UR) != 0) { - /* may NOT happen -> error log */ - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E020, SKERR_SIRQ_E020MSG); - } - - if ((IStatus & XM_IS_TX_COMP) != 0) { - /* not served here */ - } - - if ((IStatus & XM_IS_RX_COMP) != 0) { - /* not served here */ - } -} /* SkXmIrq */ -#endif /* GENESIS */ - - -#ifdef YUKON -/****************************************************************************** - * - * SkGmIrq() - Interrupt Service Routine - * - * Description: services an Interrupt Request of the GMAC - * - * Note: - * - * Returns: - * nothing - */ -static void SkGmIrq( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U8 IStatus; /* Interrupt status */ -#ifdef SK_SLIM - SK_U64 OverflowStatus; -#else - SK_EVPARA Para; -#endif - - pPrt = &pAC->GIni.GP[Port]; - - SK_IN8(IoC, GMAC_IRQ_SRC, &IStatus); - -#ifdef XXX - /* LinkPartner Auto-negable? */ - SkMacAutoNegLipaPhy(pAC, IoC, Port, IStatus); -#endif /* XXX */ - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_IRQ, - ("GmacIrq Port %d Isr 0x%04X\n", Port, IStatus)); - - /* Combined Tx & Rx Counter Overflow SIRQ Event */ - if (IStatus & (GM_IS_RX_CO_OV | GM_IS_TX_CO_OV)) { - /* these IRQs will be cleared by reading GMACs register */ -#ifdef SK_SLIM - SkGmOverflowStatus(pAC, IoC, Port, IStatus, &OverflowStatus); -#else - Para.Para32[0] = (SK_U32)Port; - Para.Para32[1] = (SK_U32)IStatus; - SkPnmiEvent(pAC, IoC, SK_PNMI_EVT_SIRQ_OVERFLOW, Para); -#endif - } - - if (IStatus & GM_IS_RX_FF_OR) { - /* clear GMAC Rx FIFO Overrun IRQ */ - SK_OUT8(IoC, MR_ADDR(Port, RX_GMF_CTRL_T), (SK_U8)GMF_CLI_RX_FO); -#ifdef DEBUG - pPrt->PRxOverCnt++; -#endif /* DEBUG */ - } - - if (IStatus & GM_IS_TX_FF_UR) { - /* clear GMAC Tx FIFO Underrun IRQ */ - SK_OUT8(IoC, MR_ADDR(Port, TX_GMF_CTRL_T), (SK_U8)GMF_CLI_TX_FU); - /* may NOT happen -> error log */ - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_SIRQ_E020, SKERR_SIRQ_E020MSG); - } - - if (IStatus & GM_IS_TX_COMPL) { - /* not served here */ - } - - if (IStatus & GM_IS_RX_COMPL) { - /* not served here */ - } -} /* SkGmIrq */ -#endif /* YUKON */ - - -/****************************************************************************** - * - * SkMacIrq() - Interrupt Service Routine for MAC - * - * Description: calls the Interrupt Service Routine dep. on board type - * - * Returns: - * nothing - */ -void SkMacIrq( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port) /* Port Index (MAC_1 + n) */ -{ -#ifdef GENESIS - if (pAC->GIni.GIGenesis) { - /* IRQ from XMAC */ - SkXmIrq(pAC, IoC, Port); - } -#endif /* GENESIS */ - -#ifdef YUKON - if (pAC->GIni.GIYukon) { - /* IRQ from GMAC */ - SkGmIrq(pAC, IoC, Port); - } -#endif /* YUKON */ - -} /* SkMacIrq */ - -#endif /* !SK_DIAG */ - -#ifdef GENESIS -/****************************************************************************** - * - * SkXmUpdateStats() - Force the XMAC to output the current statistic - * - * Description: - * The XMAC holds its statistic internally. To obtain the current - * values a command must be sent so that the statistic data will - * be written to a predefined memory area on the adapter. - * - * Returns: - * 0: success - * 1: something went wrong - */ -int SkXmUpdateStats( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -unsigned int Port) /* Port Index (MAC_1 + n) */ -{ - SK_GEPORT *pPrt; - SK_U16 StatReg; - int WaitIndex; - - pPrt = &pAC->GIni.GP[Port]; - WaitIndex = 0; - - /* Send an update command to XMAC specified */ - XM_OUT16(IoC, Port, XM_STAT_CMD, XM_SC_SNP_TXC | XM_SC_SNP_RXC); - - /* - * It is an auto-clearing register. If the command bits - * went to zero again, the statistics are transferred. - * Normally the command should be executed immediately. - * But just to be sure we execute a loop. - */ - do { - - XM_IN16(IoC, Port, XM_STAT_CMD, &StatReg); - - if (++WaitIndex > 10) { - - SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_HWI_E021, SKERR_HWI_E021MSG); - - return(1); - } - } while ((StatReg & (XM_SC_SNP_TXC | XM_SC_SNP_RXC)) != 0); - - return(0); -} /* SkXmUpdateStats */ - - -/****************************************************************************** - * - * SkXmMacStatistic() - Get XMAC counter value - * - * Description: - * Gets the 32bit counter value. Except for the octet counters - * the lower 32bit are counted in hardware and the upper 32bit - * must be counted in software by monitoring counter overflow interrupts. - * - * Returns: - * 0: success - * 1: something went wrong - */ -int SkXmMacStatistic( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -unsigned int Port, /* Port Index (MAC_1 + n) */ -SK_U16 StatAddr, /* MIB counter base address */ -SK_U32 SK_FAR *pVal) /* ptr to return statistic value */ -{ - if ((StatAddr < XM_TXF_OK) || (StatAddr > XM_RXF_MAX_SZ)) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E022, SKERR_HWI_E022MSG); - - return(1); - } - - XM_IN32(IoC, Port, StatAddr, pVal); - - return(0); -} /* SkXmMacStatistic */ - - -/****************************************************************************** - * - * SkXmResetCounter() - Clear MAC statistic counter - * - * Description: - * Force the XMAC to clear its statistic counter. - * - * Returns: - * 0: success - * 1: something went wrong - */ -int SkXmResetCounter( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -unsigned int Port) /* Port Index (MAC_1 + n) */ -{ - XM_OUT16(IoC, Port, XM_STAT_CMD, XM_SC_CLR_RXC | XM_SC_CLR_TXC); - /* Clear two times according to Errata #3 */ - XM_OUT16(IoC, Port, XM_STAT_CMD, XM_SC_CLR_RXC | XM_SC_CLR_TXC); - - return(0); -} /* SkXmResetCounter */ - - -/****************************************************************************** - * - * SkXmOverflowStatus() - Gets the status of counter overflow interrupt - * - * Description: - * Checks the source causing an counter overflow interrupt. On success the - * resulting counter overflow status is written to <pStatus>, whereas the - * upper dword stores the XMAC ReceiveCounterEvent register and the lower - * dword the XMAC TransmitCounterEvent register. - * - * Note: - * For XMAC the interrupt source is a self-clearing register, so the source - * must be checked only once. SIRQ module does another check to be sure - * that no interrupt get lost during process time. - * - * Returns: - * 0: success - * 1: something went wrong - */ -int SkXmOverflowStatus( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -unsigned int Port, /* Port Index (MAC_1 + n) */ -SK_U16 IStatus, /* Interupt Status from MAC */ -SK_U64 SK_FAR *pStatus) /* ptr for return overflow status value */ -{ - SK_U64 Status; /* Overflow status */ - SK_U32 RegVal; - - Status = 0; - - if ((IStatus & XM_IS_RXC_OV) != 0) { - - XM_IN32(IoC, Port, XM_RX_CNT_EV, &RegVal); - Status |= (SK_U64)RegVal << 32; - } - - if ((IStatus & XM_IS_TXC_OV) != 0) { - - XM_IN32(IoC, Port, XM_TX_CNT_EV, &RegVal); - Status |= (SK_U64)RegVal; - } - - *pStatus = Status; - - return(0); -} /* SkXmOverflowStatus */ -#endif /* GENESIS */ - - -#ifdef YUKON -/****************************************************************************** - * - * SkGmUpdateStats() - Force the GMAC to output the current statistic - * - * Description: - * Empty function for GMAC. Statistic data is accessible in direct way. - * - * Returns: - * 0: success - * 1: something went wrong - */ -int SkGmUpdateStats( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -unsigned int Port) /* Port Index (MAC_1 + n) */ -{ - return(0); -} - - -/****************************************************************************** - * - * SkGmMacStatistic() - Get GMAC counter value - * - * Description: - * Gets the 32bit counter value. Except for the octet counters - * the lower 32bit are counted in hardware and the upper 32bit - * must be counted in software by monitoring counter overflow interrupts. - * - * Returns: - * 0: success - * 1: something went wrong - */ -int SkGmMacStatistic( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -unsigned int Port, /* Port Index (MAC_1 + n) */ -SK_U16 StatAddr, /* MIB counter base address */ -SK_U32 SK_FAR *pVal) /* ptr to return statistic value */ -{ - - if ((StatAddr < GM_RXF_UC_OK) || (StatAddr > GM_TXE_FIFO_UR)) { - - SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E022, SKERR_HWI_E022MSG); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("SkGmMacStat: wrong MIB counter 0x%04X\n", StatAddr)); - return(1); - } - - GM_IN32(IoC, Port, StatAddr, pVal); - - return(0); -} /* SkGmMacStatistic */ - - -/****************************************************************************** - * - * SkGmResetCounter() - Clear MAC statistic counter - * - * Description: - * Force GMAC to clear its statistic counter. - * - * Returns: - * 0: success - * 1: something went wrong - */ -int SkGmResetCounter( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -unsigned int Port) /* Port Index (MAC_1 + n) */ -{ - SK_U16 Reg; /* Phy Address Register */ - SK_U16 Word; - int i; - - GM_IN16(IoC, Port, GM_PHY_ADDR, &Reg); - - /* set MIB Clear Counter Mode */ - GM_OUT16(IoC, Port, GM_PHY_ADDR, Reg | GM_PAR_MIB_CLR); - - /* read all MIB Counters with Clear Mode set */ - for (i = 0; i < GM_MIB_CNT_SIZE; i++) { - /* the reset is performed only when the lower 16 bits are read */ - GM_IN16(IoC, Port, GM_MIB_CNT_BASE + 8*i, &Word); - } - - /* clear MIB Clear Counter Mode */ - GM_OUT16(IoC, Port, GM_PHY_ADDR, Reg); - - return(0); -} /* SkGmResetCounter */ - - -/****************************************************************************** - * - * SkGmOverflowStatus() - Gets the status of counter overflow interrupt - * - * Description: - * Checks the source causing an counter overflow interrupt. On success the - * resulting counter overflow status is written to <pStatus>, whereas the - * the following bit coding is used: - * 63:56 - unused - * 55:48 - TxRx interrupt register bit7:0 - * 32:47 - Rx interrupt register - * 31:24 - unused - * 23:16 - TxRx interrupt register bit15:8 - * 15:0 - Tx interrupt register - * - * Returns: - * 0: success - * 1: something went wrong - */ -int SkGmOverflowStatus( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -unsigned int Port, /* Port Index (MAC_1 + n) */ -SK_U16 IStatus, /* Interupt Status from MAC */ -SK_U64 SK_FAR *pStatus) /* ptr for return overflow status value */ -{ - SK_U64 Status; /* Overflow status */ - SK_U16 RegVal; - - Status = 0; - - if ((IStatus & GM_IS_RX_CO_OV) != 0) { - /* this register is self-clearing after read */ - GM_IN16(IoC, Port, GM_RX_IRQ_SRC, &RegVal); - Status |= (SK_U64)RegVal << 32; - } - - if ((IStatus & GM_IS_TX_CO_OV) != 0) { - /* this register is self-clearing after read */ - GM_IN16(IoC, Port, GM_TX_IRQ_SRC, &RegVal); - Status |= (SK_U64)RegVal; - } - - /* this register is self-clearing after read */ - GM_IN16(IoC, Port, GM_TR_IRQ_SRC, &RegVal); - /* Rx overflow interrupt register bits (LoByte)*/ - Status |= (SK_U64)((SK_U8)RegVal) << 48; - /* Tx overflow interrupt register bits (HiByte)*/ - Status |= (SK_U64)(RegVal >> 8) << 16; - - *pStatus = Status; - - return(0); -} /* SkGmOverflowStatus */ - - -#ifndef SK_SLIM -/****************************************************************************** - * - * SkGmCableDiagStatus() - Starts / Gets status of cable diagnostic test - * - * Description: - * starts the cable diagnostic test if 'StartTest' is true - * gets the results if 'StartTest' is true - * - * NOTE: this test is meaningful only when link is down - * - * Returns: - * 0: success - * 1: no YUKON copper - * 2: test in progress - */ -int SkGmCableDiagStatus( -SK_AC *pAC, /* adapter context */ -SK_IOC IoC, /* IO context */ -int Port, /* Port Index (MAC_1 + n) */ -SK_BOOL StartTest) /* flag for start / get result */ -{ - int i; - SK_U16 RegVal; - SK_GEPORT *pPrt; - - pPrt = &pAC->GIni.GP[Port]; - - if (pPrt->PhyType != SK_PHY_MARV_COPPER) { - - return(1); - } - - if (StartTest) { - /* only start the cable test */ - if ((pPrt->PhyId1 & PHY_I1_REV_MSK) < 4) { - /* apply TDR workaround from Marvell */ - SkGmPhyWrite(pAC, IoC, Port, 29, 0x001e); - - SkGmPhyWrite(pAC, IoC, Port, 30, 0xcc00); - SkGmPhyWrite(pAC, IoC, Port, 30, 0xc800); - SkGmPhyWrite(pAC, IoC, Port, 30, 0xc400); - SkGmPhyWrite(pAC, IoC, Port, 30, 0xc000); - SkGmPhyWrite(pAC, IoC, Port, 30, 0xc100); - } - - /* set address to 0 for MDI[0] */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_EXT_ADR, 0); - - /* Read Cable Diagnostic Reg */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CABLE_DIAG, &RegVal); - - /* start Cable Diagnostic Test */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_CABLE_DIAG, - (SK_U16)(RegVal | PHY_M_CABD_ENA_TEST)); - - return(0); - } - - /* Read Cable Diagnostic Reg */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CABLE_DIAG, &RegVal); - - SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_CTRL, - ("PHY Cable Diag.=0x%04X\n", RegVal)); - - if ((RegVal & PHY_M_CABD_ENA_TEST) != 0) { - /* test is running */ - return(2); - } - - /* get the test results */ - for (i = 0; i < 4; i++) { - /* set address to i for MDI[i] */ - SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_EXT_ADR, (SK_U16)i); - - /* get Cable Diagnostic values */ - SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CABLE_DIAG, &RegVal); - - pPrt->PMdiPairLen[i] = (SK_U8)(RegVal & PHY_M_CABD_DIST_MSK); - - pPrt->PMdiPairSts[i] = (SK_U8)((RegVal & PHY_M_CABD_STAT_MSK) >> 13); - } - - return(0); -} /* SkGmCableDiagStatus */ -#endif /* !SK_SLIM */ -#endif /* YUKON */ - -/* End of file */ |