diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath10k/wmi.h')
| -rw-r--r-- | drivers/net/wireless/ath/ath10k/wmi.h | 1037 |
1 files changed, 1020 insertions, 17 deletions
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h index 2c5a4f8daf2e..78c991aec7f9 100644 --- a/drivers/net/wireless/ath/ath10k/wmi.h +++ b/drivers/net/wireless/ath/ath10k/wmi.h @@ -208,6 +208,118 @@ struct wmi_mac_addr { (c_macaddr)[5] = (((pwmi_mac_addr)->word1) >> 8) & 0xff; \ } while (0) +struct wmi_cmd_map { + u32 init_cmdid; + u32 start_scan_cmdid; + u32 stop_scan_cmdid; + u32 scan_chan_list_cmdid; + u32 scan_sch_prio_tbl_cmdid; + u32 pdev_set_regdomain_cmdid; + u32 pdev_set_channel_cmdid; + u32 pdev_set_param_cmdid; + u32 pdev_pktlog_enable_cmdid; + u32 pdev_pktlog_disable_cmdid; + u32 pdev_set_wmm_params_cmdid; + u32 pdev_set_ht_cap_ie_cmdid; + u32 pdev_set_vht_cap_ie_cmdid; + u32 pdev_set_dscp_tid_map_cmdid; + u32 pdev_set_quiet_mode_cmdid; + u32 pdev_green_ap_ps_enable_cmdid; + u32 pdev_get_tpc_config_cmdid; + u32 pdev_set_base_macaddr_cmdid; + u32 vdev_create_cmdid; + u32 vdev_delete_cmdid; + u32 vdev_start_request_cmdid; + u32 vdev_restart_request_cmdid; + u32 vdev_up_cmdid; + u32 vdev_stop_cmdid; + u32 vdev_down_cmdid; + u32 vdev_set_param_cmdid; + u32 vdev_install_key_cmdid; + u32 peer_create_cmdid; + u32 peer_delete_cmdid; + u32 peer_flush_tids_cmdid; + u32 peer_set_param_cmdid; + u32 peer_assoc_cmdid; + u32 peer_add_wds_entry_cmdid; + u32 peer_remove_wds_entry_cmdid; + u32 peer_mcast_group_cmdid; + u32 bcn_tx_cmdid; + u32 pdev_send_bcn_cmdid; + u32 bcn_tmpl_cmdid; + u32 bcn_filter_rx_cmdid; + u32 prb_req_filter_rx_cmdid; + u32 mgmt_tx_cmdid; + u32 prb_tmpl_cmdid; + u32 addba_clear_resp_cmdid; + u32 addba_send_cmdid; + u32 addba_status_cmdid; + u32 delba_send_cmdid; + u32 addba_set_resp_cmdid; + u32 send_singleamsdu_cmdid; + u32 sta_powersave_mode_cmdid; + u32 sta_powersave_param_cmdid; + u32 sta_mimo_ps_mode_cmdid; + u32 pdev_dfs_enable_cmdid; + u32 pdev_dfs_disable_cmdid; + u32 roam_scan_mode; + u32 roam_scan_rssi_threshold; + u32 roam_scan_period; + u32 roam_scan_rssi_change_threshold; + u32 roam_ap_profile; + u32 ofl_scan_add_ap_profile; + u32 ofl_scan_remove_ap_profile; + u32 ofl_scan_period; + u32 p2p_dev_set_device_info; + u32 p2p_dev_set_discoverability; + u32 p2p_go_set_beacon_ie; + u32 p2p_go_set_probe_resp_ie; + u32 p2p_set_vendor_ie_data_cmdid; + u32 ap_ps_peer_param_cmdid; + u32 ap_ps_peer_uapsd_coex_cmdid; + u32 peer_rate_retry_sched_cmdid; + u32 wlan_profile_trigger_cmdid; + u32 wlan_profile_set_hist_intvl_cmdid; + u32 wlan_profile_get_profile_data_cmdid; + u32 wlan_profile_enable_profile_id_cmdid; + u32 wlan_profile_list_profile_id_cmdid; + u32 pdev_suspend_cmdid; + u32 pdev_resume_cmdid; + u32 add_bcn_filter_cmdid; + u32 rmv_bcn_filter_cmdid; + u32 wow_add_wake_pattern_cmdid; + u32 wow_del_wake_pattern_cmdid; + u32 wow_enable_disable_wake_event_cmdid; + u32 wow_enable_cmdid; + u32 wow_hostwakeup_from_sleep_cmdid; + u32 rtt_measreq_cmdid; + u32 rtt_tsf_cmdid; + u32 vdev_spectral_scan_configure_cmdid; + u32 vdev_spectral_scan_enable_cmdid; + u32 request_stats_cmdid; + u32 set_arp_ns_offload_cmdid; + u32 network_list_offload_config_cmdid; + u32 gtk_offload_cmdid; + u32 csa_offload_enable_cmdid; + u32 csa_offload_chanswitch_cmdid; + u32 chatter_set_mode_cmdid; + u32 peer_tid_addba_cmdid; + u32 peer_tid_delba_cmdid; + u32 sta_dtim_ps_method_cmdid; + u32 sta_uapsd_auto_trig_cmdid; + u32 sta_keepalive_cmd; + u32 echo_cmdid; + u32 pdev_utf_cmdid; + u32 dbglog_cfg_cmdid; + u32 pdev_qvit_cmdid; + u32 pdev_ftm_intg_cmdid; + u32 vdev_set_keepalive_cmdid; + u32 vdev_get_keepalive_cmdid; + u32 force_fw_hang_cmdid; + u32 gpio_config_cmdid; + u32 gpio_output_cmdid; +}; + /* * wmi command groups. */ @@ -247,7 +359,9 @@ enum wmi_cmd_group { #define WMI_CMD_GRP(grp_id) (((grp_id) << 12) | 0x1) #define WMI_EVT_GRP_START_ID(grp_id) (((grp_id) << 12) | 0x1) -/* Command IDs and commande events. */ +#define WMI_CMD_UNSUPPORTED 0 + +/* Command IDs and command events for MAIN FW. */ enum wmi_cmd_id { WMI_INIT_CMDID = 0x1, @@ -488,6 +602,217 @@ enum wmi_event_id { WMI_GPIO_INPUT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_GPIO), }; +/* Command IDs and command events for 10.X firmware */ +enum wmi_10x_cmd_id { + WMI_10X_START_CMDID = 0x9000, + WMI_10X_END_CMDID = 0x9FFF, + + /* initialize the wlan sub system */ + WMI_10X_INIT_CMDID, + + /* Scan specific commands */ + + WMI_10X_START_SCAN_CMDID = WMI_10X_START_CMDID, + WMI_10X_STOP_SCAN_CMDID, + WMI_10X_SCAN_CHAN_LIST_CMDID, + WMI_10X_ECHO_CMDID, + + /* PDEV(physical device) specific commands */ + WMI_10X_PDEV_SET_REGDOMAIN_CMDID, + WMI_10X_PDEV_SET_CHANNEL_CMDID, + WMI_10X_PDEV_SET_PARAM_CMDID, + WMI_10X_PDEV_PKTLOG_ENABLE_CMDID, + WMI_10X_PDEV_PKTLOG_DISABLE_CMDID, + WMI_10X_PDEV_SET_WMM_PARAMS_CMDID, + WMI_10X_PDEV_SET_HT_CAP_IE_CMDID, + WMI_10X_PDEV_SET_VHT_CAP_IE_CMDID, + WMI_10X_PDEV_SET_BASE_MACADDR_CMDID, + WMI_10X_PDEV_SET_DSCP_TID_MAP_CMDID, + WMI_10X_PDEV_SET_QUIET_MODE_CMDID, + WMI_10X_PDEV_GREEN_AP_PS_ENABLE_CMDID, + WMI_10X_PDEV_GET_TPC_CONFIG_CMDID, + + /* VDEV(virtual device) specific commands */ + WMI_10X_VDEV_CREATE_CMDID, + WMI_10X_VDEV_DELETE_CMDID, + WMI_10X_VDEV_START_REQUEST_CMDID, + WMI_10X_VDEV_RESTART_REQUEST_CMDID, + WMI_10X_VDEV_UP_CMDID, + WMI_10X_VDEV_STOP_CMDID, + WMI_10X_VDEV_DOWN_CMDID, + WMI_10X_VDEV_STANDBY_RESPONSE_CMDID, + WMI_10X_VDEV_RESUME_RESPONSE_CMDID, + WMI_10X_VDEV_SET_PARAM_CMDID, + WMI_10X_VDEV_INSTALL_KEY_CMDID, + + /* peer specific commands */ + WMI_10X_PEER_CREATE_CMDID, + WMI_10X_PEER_DELETE_CMDID, + WMI_10X_PEER_FLUSH_TIDS_CMDID, + WMI_10X_PEER_SET_PARAM_CMDID, + WMI_10X_PEER_ASSOC_CMDID, + WMI_10X_PEER_ADD_WDS_ENTRY_CMDID, + WMI_10X_PEER_REMOVE_WDS_ENTRY_CMDID, + WMI_10X_PEER_MCAST_GROUP_CMDID, + + /* beacon/management specific commands */ + + WMI_10X_BCN_TX_CMDID, + WMI_10X_BCN_PRB_TMPL_CMDID, + WMI_10X_BCN_FILTER_RX_CMDID, + WMI_10X_PRB_REQ_FILTER_RX_CMDID, + WMI_10X_MGMT_TX_CMDID, + + /* commands to directly control ba negotiation directly from host. */ + WMI_10X_ADDBA_CLEAR_RESP_CMDID, + WMI_10X_ADDBA_SEND_CMDID, + WMI_10X_ADDBA_STATUS_CMDID, + WMI_10X_DELBA_SEND_CMDID, + WMI_10X_ADDBA_SET_RESP_CMDID, + WMI_10X_SEND_SINGLEAMSDU_CMDID, + + /* Station power save specific config */ + WMI_10X_STA_POWERSAVE_MODE_CMDID, + WMI_10X_STA_POWERSAVE_PARAM_CMDID, + WMI_10X_STA_MIMO_PS_MODE_CMDID, + + /* set debug log config */ + WMI_10X_DBGLOG_CFG_CMDID, + + /* DFS-specific commands */ + WMI_10X_PDEV_DFS_ENABLE_CMDID, + WMI_10X_PDEV_DFS_DISABLE_CMDID, + + /* QVIT specific command id */ + WMI_10X_PDEV_QVIT_CMDID, + + /* Offload Scan and Roaming related commands */ + WMI_10X_ROAM_SCAN_MODE, + WMI_10X_ROAM_SCAN_RSSI_THRESHOLD, + WMI_10X_ROAM_SCAN_PERIOD, + WMI_10X_ROAM_SCAN_RSSI_CHANGE_THRESHOLD, + WMI_10X_ROAM_AP_PROFILE, + WMI_10X_OFL_SCAN_ADD_AP_PROFILE, + WMI_10X_OFL_SCAN_REMOVE_AP_PROFILE, + WMI_10X_OFL_SCAN_PERIOD, + + /* P2P specific commands */ + WMI_10X_P2P_DEV_SET_DEVICE_INFO, + WMI_10X_P2P_DEV_SET_DISCOVERABILITY, + WMI_10X_P2P_GO_SET_BEACON_IE, + WMI_10X_P2P_GO_SET_PROBE_RESP_IE, + + /* AP power save specific config */ + WMI_10X_AP_PS_PEER_PARAM_CMDID, + WMI_10X_AP_PS_PEER_UAPSD_COEX_CMDID, + + /* Rate-control specific commands */ + WMI_10X_PEER_RATE_RETRY_SCHED_CMDID, + + /* WLAN Profiling commands. */ + WMI_10X_WLAN_PROFILE_TRIGGER_CMDID, + WMI_10X_WLAN_PROFILE_SET_HIST_INTVL_CMDID, + WMI_10X_WLAN_PROFILE_GET_PROFILE_DATA_CMDID, + WMI_10X_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID, + WMI_10X_WLAN_PROFILE_LIST_PROFILE_ID_CMDID, + + /* Suspend resume command Ids */ + WMI_10X_PDEV_SUSPEND_CMDID, + WMI_10X_PDEV_RESUME_CMDID, + + /* Beacon filter commands */ + WMI_10X_ADD_BCN_FILTER_CMDID, + WMI_10X_RMV_BCN_FILTER_CMDID, + + /* WOW Specific WMI commands*/ + WMI_10X_WOW_ADD_WAKE_PATTERN_CMDID, + WMI_10X_WOW_DEL_WAKE_PATTERN_CMDID, + WMI_10X_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID, + WMI_10X_WOW_ENABLE_CMDID, + WMI_10X_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID, + + /* RTT measurement related cmd */ + WMI_10X_RTT_MEASREQ_CMDID, + WMI_10X_RTT_TSF_CMDID, + + /* transmit beacon by value */ + WMI_10X_PDEV_SEND_BCN_CMDID, + + /* F/W stats */ + WMI_10X_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID, + WMI_10X_VDEV_SPECTRAL_SCAN_ENABLE_CMDID, + WMI_10X_REQUEST_STATS_CMDID, + + /* GPIO Configuration */ + WMI_10X_GPIO_CONFIG_CMDID, + WMI_10X_GPIO_OUTPUT_CMDID, + + WMI_10X_PDEV_UTF_CMDID = WMI_10X_END_CMDID - 1, +}; + +enum wmi_10x_event_id { + WMI_10X_SERVICE_READY_EVENTID = 0x8000, + WMI_10X_READY_EVENTID, + WMI_10X_START_EVENTID = 0x9000, + WMI_10X_END_EVENTID = 0x9FFF, + + /* Scan specific events */ + WMI_10X_SCAN_EVENTID = WMI_10X_START_EVENTID, + WMI_10X_ECHO_EVENTID, + WMI_10X_DEBUG_MESG_EVENTID, + WMI_10X_UPDATE_STATS_EVENTID, + + /* Instantaneous RSSI event */ + WMI_10X_INST_RSSI_STATS_EVENTID, + + /* VDEV specific events */ + WMI_10X_VDEV_START_RESP_EVENTID, + WMI_10X_VDEV_STANDBY_REQ_EVENTID, + WMI_10X_VDEV_RESUME_REQ_EVENTID, + WMI_10X_VDEV_STOPPED_EVENTID, + + /* peer specific events */ + WMI_10X_PEER_STA_KICKOUT_EVENTID, + + /* beacon/mgmt specific events */ + WMI_10X_HOST_SWBA_EVENTID, + WMI_10X_TBTTOFFSET_UPDATE_EVENTID, + WMI_10X_MGMT_RX_EVENTID, + + /* Channel stats event */ + WMI_10X_CHAN_INFO_EVENTID, + + /* PHY Error specific WMI event */ + WMI_10X_PHYERR_EVENTID, + + /* Roam event to trigger roaming on host */ + WMI_10X_ROAM_EVENTID, + + /* matching AP found from list of profiles */ + WMI_10X_PROFILE_MATCH, + + /* debug print message used for tracing FW code while debugging */ + WMI_10X_DEBUG_PRINT_EVENTID, + /* VI spoecific event */ + WMI_10X_PDEV_QVIT_EVENTID, + /* FW code profile data in response to profile request */ + WMI_10X_WLAN_PROFILE_DATA_EVENTID, + + /*RTT related event ID*/ + WMI_10X_RTT_MEASUREMENT_REPORT_EVENTID, + WMI_10X_TSF_MEASUREMENT_REPORT_EVENTID, + WMI_10X_RTT_ERROR_REPORT_EVENTID, + + WMI_10X_WOW_WAKEUP_HOST_EVENTID, + WMI_10X_DCS_INTERFERENCE_EVENTID, + + /* TPC config for the current operating channel */ + WMI_10X_PDEV_TPC_CONFIG_EVENTID, + + WMI_10X_GPIO_INPUT_EVENTID, + WMI_10X_PDEV_UTF_EVENTID = WMI_10X_END_EVENTID-1, +}; + enum wmi_phy_mode { MODE_11A = 0, /* 11a Mode */ MODE_11G = 1, /* 11b/g Mode */ @@ -508,6 +833,48 @@ enum wmi_phy_mode { MODE_MAX = 14 }; +static inline const char *ath10k_wmi_phymode_str(enum wmi_phy_mode mode) +{ + switch (mode) { + case MODE_11A: + return "11a"; + case MODE_11G: + return "11g"; + case MODE_11B: + return "11b"; + case MODE_11GONLY: + return "11gonly"; + case MODE_11NA_HT20: + return "11na-ht20"; + case MODE_11NG_HT20: + return "11ng-ht20"; + case MODE_11NA_HT40: + return "11na-ht40"; + case MODE_11NG_HT40: + return "11ng-ht40"; + case MODE_11AC_VHT20: + return "11ac-vht20"; + case MODE_11AC_VHT40: + return "11ac-vht40"; + case MODE_11AC_VHT80: + return "11ac-vht80"; + case MODE_11AC_VHT20_2G: + return "11ac-vht20-2g"; + case MODE_11AC_VHT40_2G: + return "11ac-vht40-2g"; + case MODE_11AC_VHT80_2G: + return "11ac-vht80-2g"; + case MODE_UNKNOWN: + /* skip */ + break; + + /* no default handler to allow compiler to check that the + * enum is fully handled */ + }; + + return "<unknown>"; +} + #define WMI_CHAN_LIST_TAG 0x1 #define WMI_SSID_LIST_TAG 0x2 #define WMI_BSSID_LIST_TAG 0x3 @@ -763,13 +1130,45 @@ struct wmi_service_ready_event { struct wlan_host_mem_req mem_reqs[1]; } __packed; -/* - * status consists of upper 16 bits fo int status and lower 16 bits of - * module ID that retuned status - */ -#define WLAN_INIT_STATUS_SUCCESS 0x0 -#define WLAN_GET_INIT_STATUS_REASON(status) ((status) & 0xffff) -#define WLAN_GET_INIT_STATUS_MODULE_ID(status) (((status) >> 16) & 0xffff) +/* This is the definition from 10.X firmware branch */ +struct wmi_service_ready_event_10x { + __le32 sw_version; + __le32 abi_version; + + /* WMI_PHY_CAPABILITY */ + __le32 phy_capability; + + /* Maximum number of frag table entries that SW will populate less 1 */ + __le32 max_frag_entry; + __le32 wmi_service_bitmap[WMI_SERVICE_BM_SIZE]; + __le32 num_rf_chains; + + /* + * The following field is only valid for service type + * WMI_SERVICE_11AC + */ + __le32 ht_cap_info; /* WMI HT Capability */ + __le32 vht_cap_info; /* VHT capability info field of 802.11ac */ + __le32 vht_supp_mcs; /* VHT Supported MCS Set field Rx/Tx same */ + __le32 hw_min_tx_power; + __le32 hw_max_tx_power; + + struct hal_reg_capabilities hal_reg_capabilities; + + __le32 sys_cap_info; + __le32 min_pkt_size_enable; /* Enterprise mode short pkt enable */ + + /* + * request to host to allocate a chuck of memory and pss it down to FW + * via WM_INIT. FW uses this as FW extesnsion memory for saving its + * data structures. Only valid for low latency interfaces like PCIE + * where FW can access this memory directly (or) by DMA. + */ + __le32 num_mem_reqs; + + struct wlan_host_mem_req mem_reqs[1]; +} __packed; + #define WMI_SERVICE_READY_TIMEOUT_HZ (5*HZ) #define WMI_UNIFIED_READY_TIMEOUT_HZ (5*HZ) @@ -978,6 +1377,192 @@ struct wmi_resource_config { __le32 max_frag_entries; } __packed; +struct wmi_resource_config_10x { + /* number of virtual devices (VAPs) to support */ + __le32 num_vdevs; + + /* number of peer nodes to support */ + __le32 num_peers; + + /* number of keys per peer */ + __le32 num_peer_keys; + + /* total number of TX/RX data TIDs */ + __le32 num_tids; + + /* + * max skid for resolving hash collisions + * + * The address search table is sparse, so that if two MAC addresses + * result in the same hash value, the second of these conflicting + * entries can slide to the next index in the address search table, + * and use it, if it is unoccupied. This ast_skid_limit parameter + * specifies the upper bound on how many subsequent indices to search + * over to find an unoccupied space. + */ + __le32 ast_skid_limit; + + /* + * the nominal chain mask for transmit + * + * The chain mask may be modified dynamically, e.g. to operate AP + * tx with a reduced number of chains if no clients are associated. + * This configuration parameter specifies the nominal chain-mask that + * should be used when not operating with a reduced set of tx chains. + */ + __le32 tx_chain_mask; + + /* + * the nominal chain mask for receive + * + * The chain mask may be modified dynamically, e.g. for a client + * to use a reduced number of chains for receive if the traffic to + * the client is low enough that it doesn't require downlink MIMO + * or antenna diversity. + * This configuration parameter specifies the nominal chain-mask that + * should be used when not operating with a reduced set of rx chains. + */ + __le32 rx_chain_mask; + + /* + * what rx reorder timeout (ms) to use for the AC + * + * Each WMM access class (voice, video, best-effort, background) will + * have its own timeout value to dictate how long to wait for missing + * rx MPDUs to arrive before flushing subsequent MPDUs that have + * already been received. + * This parameter specifies the timeout in milliseconds for each + * class. + */ + __le32 rx_timeout_pri_vi; + __le32 rx_timeout_pri_vo; + __le32 rx_timeout_pri_be; + __le32 rx_timeout_pri_bk; + + /* + * what mode the rx should decap packets to + * + * MAC can decap to RAW (no decap), native wifi or Ethernet types + * THis setting also determines the default TX behavior, however TX + * behavior can be modified on a per VAP basis during VAP init + */ + __le32 rx_decap_mode; + + /* what is the maximum scan requests than can be queued */ + __le32 scan_max_pending_reqs; + + /* maximum VDEV that could use BMISS offload */ + __le32 bmiss_offload_max_vdev; + + /* maximum VDEV that could use offload roaming */ + __le32 roam_offload_max_vdev; + + /* maximum AP profiles that would push to offload roaming */ + __le32 roam_offload_max_ap_profiles; + + /* + * how many groups to use for mcast->ucast conversion + * + * The target's WAL maintains a table to hold information regarding + * which peers belong to a given multicast group, so that if + * multicast->unicast conversion is enabled, the target can convert + * multicast tx frames to a series of unicast tx frames, to each + * peer within the multicast group. + This num_mcast_groups configuration parameter tells the target how + * many multicast groups to provide storage for within its multicast + * group membership table. + */ + __le32 num_mcast_groups; + + /* + * size to alloc for the mcast membership table + * + * This num_mcast_table_elems configuration parameter tells the + * target how many peer elements it needs to provide storage for in + * its multicast group membership table. + * These multicast group membership table elements are shared by the + * multicast groups stored within the table. + */ + __le32 num_mcast_table_elems; + + /* + * whether/how to do multicast->unicast conversion + * + * This configuration parameter specifies whether the target should + * perform multicast --> unicast conversion on transmit, and if so, + * what to do if it finds no entries in its multicast group + * membership table for the multicast IP address in the tx frame. + * Configuration value: + * 0 -> Do not perform multicast to unicast conversion. + * 1 -> Convert multicast frames to unicast, if the IP multicast + * address from the tx frame is found in the multicast group + * membership table. If the IP multicast address is not found, + * drop the frame. + * 2 -> Convert multicast frames to unicast, if the IP multicast + * address from the tx frame is found in the multicast group + * membership table. If the IP multicast address is not found, + * transmit the frame as multicast. + */ + __le32 mcast2ucast_mode; + + /* + * how much memory to allocate for a tx PPDU dbg log + * + * This parameter controls how much memory the target will allocate + * to store a log of tx PPDU meta-information (how large the PPDU + * was, when it was sent, whether it was successful, etc.) + */ + __le32 tx_dbg_log_size; + + /* how many AST entries to be allocated for WDS */ + __le32 num_wds_entries; + + /* + * MAC DMA burst size, e.g., For target PCI limit can be + * 0 -default, 1 256B + */ + __le32 dma_burst_size; + + /* + * Fixed delimiters to be inserted after every MPDU to + * account for interface latency to avoid underrun. + */ + __le32 mac_aggr_delim; + + /* + * determine whether target is responsible for detecting duplicate + * non-aggregate MPDU and timing out stale fragments. + * + * A-MPDU reordering is always performed on the target. + * + * 0: target responsible for frag timeout and dup checking + * 1: host responsible for frag timeout and dup checking + */ + __le32 rx_skip_defrag_timeout_dup_detection_check; + + /* + * Configuration for VoW : + * No of Video Nodes to be supported + * and Max no of descriptors for each Video link (node). + */ + __le32 vow_config; + + /* Number of msdu descriptors target should use */ + __le32 num_msdu_desc; + + /* + * Max. number of Tx fragments per MSDU + * This parameter controls the max number of Tx fragments per MSDU. + * This is sent by the target as part of the WMI_SERVICE_READY event + * and is overriden by the OS shim as required. + */ + __le32 max_frag_entries; +} __packed; + + +#define NUM_UNITS_IS_NUM_VDEVS 0x1 +#define NUM_UNITS_IS_NUM_PEERS 0x2 + /* strucutre describing host memory chunk. */ struct host_memory_chunk { /* id of the request that is passed up in service ready */ @@ -999,6 +1584,18 @@ struct wmi_init_cmd { struct host_memory_chunk host_mem_chunks[1]; } __packed; +/* _10x stucture is from 10.X FW API */ +struct wmi_init_cmd_10x { + struct wmi_resource_config_10x resource_config; + __le32 num_host_mem_chunks; + + /* + * variable number of host memory chunks. + * This should be the last element in the structure + */ + struct host_memory_chunk host_mem_chunks[1]; +} __packed; + /* TLV for channel list */ struct wmi_chan_list { __le32 tag; /* WMI_CHAN_LIST_TAG */ @@ -1118,6 +1715,88 @@ struct wmi_start_scan_cmd { */ } __packed; +/* This is the definition from 10.X firmware branch */ +struct wmi_start_scan_cmd_10x { + /* Scan ID */ + __le32 scan_id; + + /* Scan requestor ID */ + __le32 scan_req_id; + + /* VDEV id(interface) that is requesting scan */ + __le32 vdev_id; + + /* Scan Priority, input to scan scheduler */ + __le32 scan_priority; + + /* Scan events subscription */ + __le32 notify_scan_events; + + /* dwell time in msec on active channels */ + __le32 dwell_time_active; + + /* dwell time in msec on passive channels */ + __le32 dwell_time_passive; + + /* + * min time in msec on the BSS channel,only valid if atleast one + * VDEV is active + */ + __le32 min_rest_time; + + /* + * max rest time in msec on the BSS channel,only valid if at least + * one VDEV is active + */ + /* + * the scanner will rest on the bss channel at least min_rest_time + * after min_rest_time the scanner will start checking for tx/rx + * activity on all VDEVs. if there is no activity the scanner will + * switch to off channel. if there is activity the scanner will let + * the radio on the bss channel until max_rest_time expires.at + * max_rest_time scanner will switch to off channel irrespective of + * activity. activity is determined by the idle_time parameter. + */ + __le32 max_rest_time; + + /* + * time before sending next set of probe requests. + * The scanner keeps repeating probe requests transmission with + * period specified by repeat_probe_time. + * The number of probe requests specified depends on the ssid_list + * and bssid_list + */ + __le32 repeat_probe_time; + + /* time in msec between 2 consequetive probe requests with in a set. */ + __le32 probe_spacing_time; + + /* + * data inactivity time in msec on bss channel that will be used by + * scanner for measuring the inactivity. + */ + __le32 idle_time; + + /* maximum time in msec allowed for scan */ + __le32 max_scan_time; + + /* + * delay in msec before sending first probe request after switching + * to a channel + */ + __le32 probe_delay; + + /* Scan control flags */ + __le32 scan_ctrl_flags; + + /* + * TLV (tag length value ) paramerters follow the scan_cmd structure. + * TLV can contain channel list, bssid list, ssid list and + * ie. the TLV tags are defined above; + */ +} __packed; + + struct wmi_ssid_arg { int len; const u8 *ssid; @@ -1268,7 +1947,7 @@ struct wmi_scan_event { * good idea to pass all the fields in the RX status * descriptor up to the host. */ -struct wmi_mgmt_rx_hdr { +struct wmi_mgmt_rx_hdr_v1 { __le32 channel; __le32 snr; __le32 rate; @@ -1277,8 +1956,18 @@ struct wmi_mgmt_rx_hdr { __le32 status; /* %WMI_RX_STATUS_ */ } __packed; -struct wmi_mgmt_rx_event { - struct wmi_mgmt_rx_hdr hdr; +struct wmi_mgmt_rx_hdr_v2 { + struct wmi_mgmt_rx_hdr_v1 v1; + __le32 rssi_ctl[4]; +} __packed; + +struct wmi_mgmt_rx_event_v1 { + struct wmi_mgmt_rx_hdr_v1 hdr; + u8 buf[0]; +} __packed; + +struct wmi_mgmt_rx_event_v2 { + struct wmi_mgmt_rx_hdr_v2 hdr; u8 buf[0]; } __packed; @@ -1465,6 +2154,60 @@ struct wmi_csa_event { #define VDEV_DEFAULT_STATS_UPDATE_PERIOD 500 #define PEER_DEFAULT_STATS_UPDATE_PERIOD 500 +struct wmi_pdev_param_map { + u32 tx_chain_mask; + u32 rx_chain_mask; + u32 txpower_limit2g; + u32 txpower_limit5g; + u32 txpower_scale; + u32 beacon_gen_mode; + u32 beacon_tx_mode; + u32 resmgr_offchan_mode; + u32 protection_mode; + u32 dynamic_bw; + u32 non_agg_sw_retry_th; + u32 agg_sw_retry_th; + u32 sta_kickout_th; + u32 ac_aggrsize_scaling; + u32 ltr_enable; + u32 ltr_ac_latency_be; + u32 ltr_ac_latency_bk; + u32 ltr_ac_latency_vi; + u32 ltr_ac_latency_vo; + u32 ltr_ac_latency_timeout; + u32 ltr_sleep_override; + u32 ltr_rx_override; + u32 ltr_tx_activity_timeout; + u32 l1ss_enable; + u32 dsleep_enable; + u32 pcielp_txbuf_flush; + u32 pcielp_txbuf_watermark; + u32 pcielp_txbuf_tmo_en; + u32 pcielp_txbuf_tmo_value; + u32 pdev_stats_update_period; + u32 vdev_stats_update_period; + u32 peer_stats_update_period; + u32 bcnflt_stats_update_period; + u32 pmf_qos; + u32 arp_ac_override; + u32 arpdhcp_ac_override; + u32 dcs; + u32 ani_enable; + u32 ani_poll_period; + u32 ani_listen_period; + u32 ani_ofdm_level; + u32 ani_cck_level; + u32 dyntxchain; + u32 proxy_sta; + u32 idle_ps_config; + u32 power_gating_sleep; + u32 fast_channel_reset; + u32 burst_dur; + u32 burst_enable; +}; + +#define WMI_PDEV_PARAM_UNSUPPORTED 0 + enum wmi_pdev_param { /* TX chian mask */ WMI_PDEV_PARAM_TX_CHAIN_MASK = 0x1, @@ -1564,6 +2307,97 @@ enum wmi_pdev_param { WMI_PDEV_PARAM_POWER_GATING_SLEEP, }; +enum wmi_10x_pdev_param { + /* TX chian mask */ + WMI_10X_PDEV_PARAM_TX_CHAIN_MASK = 0x1, + /* RX chian mask */ + WMI_10X_PDEV_PARAM_RX_CHAIN_MASK, + /* TX power limit for 2G Radio */ + WMI_10X_PDEV_PARAM_TXPOWER_LIMIT2G, + /* TX power limit for 5G Radio */ + WMI_10X_PDEV_PARAM_TXPOWER_LIMIT5G, + /* TX power scale */ + WMI_10X_PDEV_PARAM_TXPOWER_SCALE, + /* Beacon generation mode . 0: host, 1: target */ + WMI_10X_PDEV_PARAM_BEACON_GEN_MODE, + /* Beacon generation mode . 0: staggered 1: bursted */ + WMI_10X_PDEV_PARAM_BEACON_TX_MODE, + /* + * Resource manager off chan mode . + * 0: turn off off chan mode. 1: turn on offchan mode + */ + WMI_10X_PDEV_PARAM_RESMGR_OFFCHAN_MODE, + /* + * Protection mode: + * 0: no protection 1:use CTS-to-self 2: use RTS/CTS + */ + WMI_10X_PDEV_PARAM_PROTECTION_MODE, + /* Dynamic bandwidth 0: disable 1: enable */ + WMI_10X_PDEV_PARAM_DYNAMIC_BW, + /* Non aggregrate/ 11g sw retry threshold.0-disable */ + WMI_10X_PDEV_PARAM_NON_AGG_SW_RETRY_TH, + /* aggregrate sw retry threshold. 0-disable*/ + WMI_10X_PDEV_PARAM_AGG_SW_RETRY_TH, + /* Station kickout threshold (non of consecutive failures).0-disable */ + WMI_10X_PDEV_PARAM_STA_KICKOUT_TH, + /* Aggerate size scaling configuration per AC */ + WMI_10X_PDEV_PARAM_AC_AGGRSIZE_SCALING, + /* LTR enable */ + WMI_10X_PDEV_PARAM_LTR_ENABLE, + /* LTR latency for BE, in us */ + WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BE, + /* LTR latency for BK, in us */ + WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BK, + /* LTR latency for VI, in us */ + WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VI, + /* LTR latency for VO, in us */ + WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VO, + /* LTR AC latency timeout, in ms */ + WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT, + /* LTR platform latency override, in us */ + WMI_10X_PDEV_PARAM_LTR_SLEEP_OVERRIDE, + /* LTR-RX override, in us */ + WMI_10X_PDEV_PARAM_LTR_RX_OVERRIDE, + /* Tx activity timeout for LTR, in us */ + WMI_10X_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT, + /* L1SS state machine enable */ + WMI_10X_PDEV_PARAM_L1SS_ENABLE, + /* Deep sleep state machine enable */ + WMI_10X_PDEV_PARAM_DSLEEP_ENABLE, + /* pdev level stats update period in ms */ + WMI_10X_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD, + /* vdev level stats update period in ms */ + WMI_10X_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD, + /* peer level stats update period in ms */ + WMI_10X_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD, + /* beacon filter status update period */ + WMI_10X_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD, + /* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */ + WMI_10X_PDEV_PARAM_PMF_QOS, + /* Access category on which ARP and DHCP frames are sent */ + WMI_10X_PDEV_PARAM_ARPDHCP_AC_OVERRIDE, + /* DCS configuration */ + WMI_10X_PDEV_PARAM_DCS, + /* Enable/Disable ANI on target */ + WMI_10X_PDEV_PARAM_ANI_ENABLE, + /* configure the ANI polling period */ + WMI_10X_PDEV_PARAM_ANI_POLL_PERIOD, + /* configure the ANI listening period */ + WMI_10X_PDEV_PARAM_ANI_LISTEN_PERIOD, + /* configure OFDM immunity level */ + WMI_10X_PDEV_PARAM_ANI_OFDM_LEVEL, + /* configure CCK immunity level */ + WMI_10X_PDEV_PARAM_ANI_CCK_LEVEL, + /* Enable/Disable CDD for 1x1 STAs in rate control module */ + WMI_10X_PDEV_PARAM_DYNTXCHAIN, + /* Enable/Disable Fast channel reset*/ + WMI_10X_PDEV_PARAM_FAST_CHANNEL_RESET, + /* Set Bursting DUR */ + WMI_10X_PDEV_PARAM_BURST_DUR, + /* Set Bursting Enable*/ + WMI_10X_PDEV_PARAM_BURST_ENABLE, +}; + struct wmi_pdev_set_param_cmd { __le32 param_id; __le32 param_value; @@ -2088,6 +2922,61 @@ enum wmi_rate_preamble { /* Value to disable fixed rate setting */ #define WMI_FIXED_RATE_NONE (0xff) +struct wmi_vdev_param_map { + u32 rts_threshold; + u32 fragmentation_threshold; + u32 beacon_interval; + u32 listen_interval; + u32 multicast_rate; + u32 mgmt_tx_rate; + u32 slot_time; + u32 preamble; + u32 swba_time; + u32 wmi_vdev_stats_update_period; + u32 wmi_vdev_pwrsave_ageout_time; + u32 wmi_vdev_host_swba_interval; + u32 dtim_period; + u32 wmi_vdev_oc_scheduler_air_time_limit; + u32 wds; + u32 atim_window; + u32 bmiss_count_max; + u32 bmiss_first_bcnt; + u32 bmiss_final_bcnt; + u32 feature_wmm; + u32 chwidth; + u32 chextoffset; + u32 disable_htprotection; + u32 sta_quickkickout; + u32 mgmt_rate; + u32 protection_mode; + u32 fixed_rate; + u32 sgi; + u32 ldpc; + u32 tx_stbc; + u32 rx_stbc; + u32 intra_bss_fwd; + u32 def_keyid; + u32 nss; + u32 bcast_data_rate; + u32 mcast_data_rate; + u32 mcast_indicate; + u32 dhcp_indicate; + u32 unknown_dest_indicate; + u32 ap_keepalive_min_idle_inactive_time_secs; + u32 ap_keepalive_max_idle_inactive_time_secs; + u32 ap_keepalive_max_unresponsive_time_secs; + u32 ap_enable_nawds; + u32 mcast2ucast_set; + u32 enable_rtscts; + u32 txbf; + u32 packet_powersave; + u32 drop_unencry; + u32 tx_encap_type; + u32 ap_detect_out_of_sync_sleeping_sta_time_secs; +}; + +#define WMI_VDEV_PARAM_UNSUPPORTED 0 + /* the definition of different VDEV parameters */ enum wmi_vdev_param { /* RTS Threshold */ @@ -2219,6 +3108,121 @@ enum wmi_vdev_param { WMI_VDEV_PARAM_TX_ENCAP_TYPE, }; +/* the definition of different VDEV parameters */ +enum wmi_10x_vdev_param { + /* RTS Threshold */ + WMI_10X_VDEV_PARAM_RTS_THRESHOLD = 0x1, + /* Fragmentation threshold */ + WMI_10X_VDEV_PARAM_FRAGMENTATION_THRESHOLD, + /* beacon interval in TUs */ + WMI_10X_VDEV_PARAM_BEACON_INTERVAL, + /* Listen interval in TUs */ + WMI_10X_VDEV_PARAM_LISTEN_INTERVAL, + /* muticast rate in Mbps */ + WMI_10X_VDEV_PARAM_MULTICAST_RATE, + /* management frame rate in Mbps */ + WMI_10X_VDEV_PARAM_MGMT_TX_RATE, + /* slot time (long vs short) */ + WMI_10X_VDEV_PARAM_SLOT_TIME, + /* preamble (long vs short) */ + WMI_10X_VDEV_PARAM_PREAMBLE, + /* SWBA time (time before tbtt in msec) */ + WMI_10X_VDEV_PARAM_SWBA_TIME, + /* time period for updating VDEV stats */ + WMI_10X_VDEV_STATS_UPDATE_PERIOD, + /* age out time in msec for frames queued for station in power save */ + WMI_10X_VDEV_PWRSAVE_AGEOUT_TIME, + /* + * Host SWBA interval (time in msec before tbtt for SWBA event + * generation). + */ + WMI_10X_VDEV_HOST_SWBA_INTERVAL, + /* DTIM period (specified in units of num beacon intervals) */ + WMI_10X_VDEV_PARAM_DTIM_PERIOD, + /* + * scheduler air time limit for this VDEV. used by off chan + * scheduler. + */ + WMI_10X_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT, + /* enable/dsiable WDS for this VDEV */ + WMI_10X_VDEV_PARAM_WDS, + /* ATIM Window */ + WMI_10X_VDEV_PARAM_ATIM_WINDOW, + /* BMISS max */ + WMI_10X_VDEV_PARAM_BMISS_COUNT_MAX, + /* WMM enables/disabled */ + WMI_10X_VDEV_PARAM_FEATURE_WMM, + /* Channel width */ + WMI_10X_VDEV_PARAM_CHWIDTH, + /* Channel Offset */ + WMI_10X_VDEV_PARAM_CHEXTOFFSET, + /* Disable HT Protection */ + WMI_10X_VDEV_PARAM_DISABLE_HTPROTECTION, + /* Quick STA Kickout */ + WMI_10X_VDEV_PARAM_STA_QUICKKICKOUT, + /* Rate to be used with Management frames */ + WMI_10X_VDEV_PARAM_MGMT_RATE, + /* Protection Mode */ + WMI_10X_VDEV_PARAM_PROTECTION_MODE, + /* Fixed rate setting */ + WMI_10X_VDEV_PARAM_FIXED_RATE, + /* Short GI Enable/Disable */ + WMI_10X_VDEV_PARAM_SGI, + /* Enable LDPC */ + WMI_10X_VDEV_PARAM_LDPC, + /* Enable Tx STBC */ + WMI_10X_VDEV_PARAM_TX_STBC, + /* Enable Rx STBC */ + WMI_10X_VDEV_PARAM_RX_STBC, + /* Intra BSS forwarding */ + WMI_10X_VDEV_PARAM_INTRA_BSS_FWD, + /* Setting Default xmit key for Vdev */ + WMI_10X_VDEV_PARAM_DEF_KEYID, + /* NSS width */ + WMI_10X_VDEV_PARAM_NSS, + /* Set the custom rate for the broadcast data frames */ + WMI_10X_VDEV_PARAM_BCAST_DATA_RATE, + /* Set the custom rate (rate-code) for multicast data frames */ + WMI_10X_VDEV_PARAM_MCAST_DATA_RATE, + /* Tx multicast packet indicate Enable/Disable */ + WMI_10X_VDEV_PARAM_MCAST_INDICATE, + /* Tx DHCP packet indicate Enable/Disable */ + WMI_10X_VDEV_PARAM_DHCP_INDICATE, + /* Enable host inspection of Tx unicast packet to unknown destination */ + WMI_10X_VDEV_PARAM_UNKNOWN_DEST_INDICATE, + + /* The minimum amount of time AP begins to consider STA inactive */ + WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS, + + /* + * An associated STA is considered inactive when there is no recent + * TX/RX activity and no downlink frames are buffered for it. Once a + * STA exceeds the maximum idle inactive time, the AP will send an + * 802.11 data-null as a keep alive to verify the STA is still + * associated. If the STA does ACK the data-null, or if the data-null + * is buffered and the STA does not retrieve it, the STA will be + * considered unresponsive + * (see WMI_10X_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS). + */ + WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS, + + /* + * An associated STA is considered unresponsive if there is no recent + * TX/RX activity and downlink frames are buffered for it. Once a STA + * exceeds the maximum unresponsive time, the AP will send a + * WMI_10X_STA_KICKOUT event to the host so the STA can be deleted. */ + WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS, + + /* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */ + WMI_10X_VDEV_PARAM_AP_ENABLE_NAWDS, + + WMI_10X_VDEV_PARAM_MCAST2UCAST_SET, + /* Enable/Disable RTS-CTS */ + WMI_10X_VDEV_PARAM_ENABLE_RTSCTS, + + WMI_10X_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS, +}; + /* slot time long */ #define WMI_VDEV_SLOT_TIME_LONG 0x1 /* slot time short */ @@ -3000,7 +4004,6 @@ struct wmi_force_fw_hang_cmd { #define WMI_MAX_EVENT 0x1000 /* Maximum number of pending TXed WMI packets */ -#define WMI_MAX_PENDING_TX_COUNT 128 #define WMI_SKB_HEADROOM sizeof(struct wmi_cmd_hdr) /* By default disable power save for IBSS */ @@ -3013,7 +4016,6 @@ int ath10k_wmi_attach(struct ath10k *ar); void ath10k_wmi_detach(struct ath10k *ar); int ath10k_wmi_wait_for_service_ready(struct ath10k *ar); int ath10k_wmi_wait_for_unified_ready(struct ath10k *ar); -void ath10k_wmi_flush_tx(struct ath10k *ar); int ath10k_wmi_connect_htc_service(struct ath10k *ar); int ath10k_wmi_pdev_set_channel(struct ath10k *ar, @@ -3022,8 +4024,7 @@ int ath10k_wmi_pdev_suspend_target(struct ath10k *ar); int ath10k_wmi_pdev_resume_target(struct ath10k *ar); int ath10k_wmi_pdev_set_regdomain(struct ath10k *ar, u16 rd, u16 rd2g, u16 rd5g, u16 ctl2g, u16 ctl5g); -int ath10k_wmi_pdev_set_param(struct ath10k *ar, enum wmi_pdev_param id, - u32 value); +int ath10k_wmi_pdev_set_param(struct ath10k *ar, u32 id, u32 value); int ath10k_wmi_cmd_init(struct ath10k *ar); int ath10k_wmi_start_scan(struct ath10k *ar, const struct wmi_start_scan_arg *); void ath10k_wmi_start_scan_init(struct ath10k *ar, struct wmi_start_scan_arg *); @@ -3043,7 +4044,7 @@ int ath10k_wmi_vdev_up(struct ath10k *ar, u32 vdev_id, u32 aid, const u8 *bssid); int ath10k_wmi_vdev_down(struct ath10k *ar, u32 vdev_id); int ath10k_wmi_vdev_set_param(struct ath10k *ar, u32 vdev_id, - enum wmi_vdev_param param_id, u32 param_value); + u32 param_id, u32 param_value); int ath10k_wmi_vdev_install_key(struct ath10k *ar, const struct wmi_vdev_install_key_arg *arg); int ath10k_wmi_peer_create(struct ath10k *ar, u32 vdev_id, @@ -3066,11 +4067,13 @@ int ath10k_wmi_set_ap_ps_param(struct ath10k *ar, u32 vdev_id, const u8 *mac, enum wmi_ap_ps_peer_param param_id, u32 value); int ath10k_wmi_scan_chan_list(struct ath10k *ar, const struct wmi_scan_chan_list_arg *arg); -int ath10k_wmi_beacon_send(struct ath10k *ar, const struct wmi_bcn_tx_arg *arg); +int ath10k_wmi_beacon_send_nowait(struct ath10k *ar, + const struct wmi_bcn_tx_arg *arg); int ath10k_wmi_pdev_set_wmm_params(struct ath10k *ar, const struct wmi_pdev_set_wmm_params_arg *arg); int ath10k_wmi_request_stats(struct ath10k *ar, enum wmi_stats_id stats_id); int ath10k_wmi_force_fw_hang(struct ath10k *ar, enum wmi_force_fw_hang_type type, u32 delay_ms); +int ath10k_wmi_mgmt_tx(struct ath10k *ar, struct sk_buff *skb); #endif /* _WMI_H_ */ |