diff options
Diffstat (limited to 'include/asm-mips/sn/sn0/addrs.h')
| -rw-r--r-- | include/asm-mips/sn/sn0/addrs.h | 288 |
1 files changed, 0 insertions, 288 deletions
diff --git a/include/asm-mips/sn/sn0/addrs.h b/include/asm-mips/sn/sn0/addrs.h deleted file mode 100644 index b06190093bbc..000000000000 --- a/include/asm-mips/sn/sn0/addrs.h +++ /dev/null @@ -1,288 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Derived from IRIX <sys/SN/SN0/addrs.h>, revision 1.126. - * - * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. - * Copyright (C) 1999 by Ralf Baechle - */ -#ifndef _ASM_SN_SN0_ADDRS_H -#define _ASM_SN_SN0_ADDRS_H - - -/* - * SN0 (on a T5) Address map - * - * This file contains a set of definitions and macros which are used - * to reference into the major address spaces (CAC, HSPEC, IO, MSPEC, - * and UNCAC) used by the SN0 architecture. It also contains addresses - * for "major" statically locatable PROM/Kernel data structures, such as - * the partition table, the configuration data structure, etc. - * We make an implicit assumption that the processor using this file - * follows the R10K's provisions for specifying uncached attributes; - * should this change, the base registers may very well become processor- - * dependent. - * - * For more information on the address spaces, see the "Local Resources" - * chapter of the Hub specification. - * - * NOTE: This header file is included both by C and by assembler source - * files. Please bracket any language-dependent definitions - * appropriately. - */ - -/* - * Some of the macros here need to be casted to appropriate types when used - * from C. They definitely must not be casted from assembly language so we - * use some new ANSI preprocessor stuff to paste these on where needed. - */ - -/* - * The following couple of definitions will eventually need to be variables, - * since the amount of address space assigned to each node depends on - * whether the system is running in N-mode (more nodes with less memory) - * or M-mode (fewer nodes with more memory). We expect that it will - * be a while before we need to make this decision dynamically, though, - * so for now we just use defines bracketed by an ifdef. - */ - -#ifdef CONFIG_SGI_SN_N_MODE - -#define NODE_SIZE_BITS 31 -#define BWIN_SIZE_BITS 28 - -#define NASID_BITS 9 -#define NASID_BITMASK (0x1ffLL) -#define NASID_SHFT 31 -#define NASID_META_BITS 5 -#define NASID_LOCAL_BITS 4 - -#define BDDIR_UPPER_MASK (UINT64_CAST 0x7ffff << 10) -#define BDECC_UPPER_MASK (UINT64_CAST 0x3ffffff << 3) - -#else /* !defined(CONFIG_SGI_SN_N_MODE), assume that M-mode is desired */ - -#define NODE_SIZE_BITS 32 -#define BWIN_SIZE_BITS 29 - -#define NASID_BITMASK (0xffLL) -#define NASID_BITS 8 -#define NASID_SHFT 32 -#define NASID_META_BITS 4 -#define NASID_LOCAL_BITS 4 - -#define BDDIR_UPPER_MASK (UINT64_CAST 0xfffff << 10) -#define BDECC_UPPER_MASK (UINT64_CAST 0x7ffffff << 3) - -#endif /* !defined(CONFIG_SGI_SN_N_MODE) */ - -#define NODE_ADDRSPACE_SIZE (UINT64_CAST 1 << NODE_SIZE_BITS) - -#define NASID_MASK (UINT64_CAST NASID_BITMASK << NASID_SHFT) -#define NASID_GET(_pa) (int) ((UINT64_CAST (_pa) >> \ - NASID_SHFT) & NASID_BITMASK) - -#if !defined(__ASSEMBLY__) - -#define NODE_SWIN_BASE(nasid, widget) \ - ((widget == 0) ? NODE_BWIN_BASE((nasid), SWIN0_BIGWIN) \ - : RAW_NODE_SWIN_BASE(nasid, widget)) -#else /* __ASSEMBLY__ */ -#define NODE_SWIN_BASE(nasid, widget) \ - (NODE_IO_BASE(nasid) + (UINT64_CAST(widget) << SWIN_SIZE_BITS)) -#endif /* __ASSEMBLY__ */ - -/* - * The following definitions pertain to the IO special address - * space. They define the location of the big and little windows - * of any given node. - */ - -#define BWIN_INDEX_BITS 3 -#define BWIN_SIZE (UINT64_CAST 1 << BWIN_SIZE_BITS) -#define BWIN_SIZEMASK (BWIN_SIZE - 1) -#define BWIN_WIDGET_MASK 0x7 -#define NODE_BWIN_BASE0(nasid) (NODE_IO_BASE(nasid) + BWIN_SIZE) -#define NODE_BWIN_BASE(nasid, bigwin) (NODE_BWIN_BASE0(nasid) + \ - (UINT64_CAST(bigwin) << BWIN_SIZE_BITS)) - -#define BWIN_WIDGETADDR(addr) ((addr) & BWIN_SIZEMASK) -#define BWIN_WINDOWNUM(addr) (((addr) >> BWIN_SIZE_BITS) & BWIN_WIDGET_MASK) -/* - * Verify if addr belongs to large window address of node with "nasid" - * - * - * NOTE: "addr" is expected to be XKPHYS address, and NOT physical - * address - * - * - */ - -#define NODE_BWIN_ADDR(nasid, addr) \ - (((addr) >= NODE_BWIN_BASE0(nasid)) && \ - ((addr) < (NODE_BWIN_BASE(nasid, HUB_NUM_BIG_WINDOW) + \ - BWIN_SIZE))) - -/* - * The following define the major position-independent aliases used - * in SN0. - * CALIAS -- Varies in size, points to the first n bytes of memory - * on the reader's node. - */ - -#define CALIAS_BASE CAC_BASE - - - -#define BRIDGE_REG_PTR(_base, _off) ((volatile bridgereg_t *) \ - ((__psunsigned_t)(_base) + (__psunsigned_t)(_off))) - -#define SN0_WIDGET_BASE(_nasid, _wid) (NODE_SWIN_BASE((_nasid), (_wid))) - -/* Turn on sable logging for the processors whose bits are set. */ -#define SABLE_LOG_TRIGGER(_map) - -#ifndef __ASSEMBLY__ -#define KERN_NMI_ADDR(nasid, slice) \ - TO_NODE_UNCAC((nasid), IP27_NMI_KREGS_OFFSET + \ - (IP27_NMI_KREGS_CPU_SIZE * (slice))) -#endif /* !__ASSEMBLY__ */ - -#ifdef PROM - -#define MISC_PROM_BASE PHYS_TO_K0(0x01300000) -#define MISC_PROM_SIZE 0x200000 - -#define DIAG_BASE PHYS_TO_K0(0x01500000) -#define DIAG_SIZE 0x300000 - -#define ROUTE_BASE PHYS_TO_K0(0x01800000) -#define ROUTE_SIZE 0x200000 - -#define IP27PROM_FLASH_HDR PHYS_TO_K0(0x01300000) -#define IP27PROM_FLASH_DATA PHYS_TO_K0(0x01301000) -#define IP27PROM_CORP_MAX 32 -#define IP27PROM_CORP PHYS_TO_K0(0x01800000) -#define IP27PROM_CORP_SIZE 0x10000 -#define IP27PROM_CORP_STK PHYS_TO_K0(0x01810000) -#define IP27PROM_CORP_STKSIZE 0x2000 -#define IP27PROM_DECOMP_BUF PHYS_TO_K0(0x01900000) -#define IP27PROM_DECOMP_SIZE 0xfff00 - -#define IP27PROM_BASE PHYS_TO_K0(0x01a00000) -#define IP27PROM_BASE_MAPPED (UNCAC_BASE | 0x1fc00000) -#define IP27PROM_SIZE_MAX 0x100000 - -#define IP27PROM_PCFG PHYS_TO_K0(0x01b00000) -#define IP27PROM_PCFG_SIZE 0xd0000 -#define IP27PROM_ERRDMP PHYS_TO_K1(0x01bd0000) -#define IP27PROM_ERRDMP_SIZE 0xf000 - -#define IP27PROM_INIT_START PHYS_TO_K1(0x01bd0000) -#define IP27PROM_CONSOLE PHYS_TO_K1(0x01bdf000) -#define IP27PROM_CONSOLE_SIZE 0x200 -#define IP27PROM_NETUART PHYS_TO_K1(0x01bdf200) -#define IP27PROM_NETUART_SIZE 0x100 -#define IP27PROM_UNUSED1 PHYS_TO_K1(0x01bdf300) -#define IP27PROM_UNUSED1_SIZE 0x500 -#define IP27PROM_ELSC_BASE_A PHYS_TO_K0(0x01bdf800) -#define IP27PROM_ELSC_BASE_B PHYS_TO_K0(0x01bdfc00) -#define IP27PROM_STACK_A PHYS_TO_K0(0x01be0000) -#define IP27PROM_STACK_B PHYS_TO_K0(0x01bf0000) -#define IP27PROM_STACK_SHFT 16 -#define IP27PROM_STACK_SIZE (1 << IP27PROM_STACK_SHFT) -#define IP27PROM_INIT_END PHYS_TO_K0(0x01c00000) - -#define SLAVESTACK_BASE PHYS_TO_K0(0x01580000) -#define SLAVESTACK_SIZE 0x40000 - -#define ENETBUFS_BASE PHYS_TO_K0(0x01f80000) -#define ENETBUFS_SIZE 0x20000 - -#define IO6PROM_BASE PHYS_TO_K0(0x01c00000) -#define IO6PROM_SIZE 0x400000 -#define IO6PROM_BASE_MAPPED (UNCAC_BASE | 0x11c00000) -#define IO6DPROM_BASE PHYS_TO_K0(0x01c00000) -#define IO6DPROM_SIZE 0x200000 - -#define NODEBUGUNIX_ADDR PHYS_TO_K0(0x00019000) -#define DEBUGUNIX_ADDR PHYS_TO_K0(0x00100000) - -#define IP27PROM_INT_LAUNCH 10 /* and 11 */ -#define IP27PROM_INT_NETUART 12 /* through 17 */ - -#endif /* PROM */ - -/* - * needed by symmon so it needs to be outside #if PROM - */ -#define IP27PROM_ELSC_SHFT 10 -#define IP27PROM_ELSC_SIZE (1 << IP27PROM_ELSC_SHFT) - -/* - * This address is used by IO6PROM to build MemoryDescriptors of - * free memory. This address is important since unix gets loaded - * at this address, and this memory has to be FREE if unix is to - * be loaded. - */ - -#define FREEMEM_BASE PHYS_TO_K0(0x2000000) - -#define IO6PROM_STACK_SHFT 14 /* stack per cpu */ -#define IO6PROM_STACK_SIZE (1 << IO6PROM_STACK_SHFT) - -/* - * IP27 PROM vectors - */ - -#define IP27PROM_ENTRY PHYS_TO_COMPATK1(0x1fc00000) -#define IP27PROM_RESTART PHYS_TO_COMPATK1(0x1fc00008) -#define IP27PROM_SLAVELOOP PHYS_TO_COMPATK1(0x1fc00010) -#define IP27PROM_PODMODE PHYS_TO_COMPATK1(0x1fc00018) -#define IP27PROM_IOC3UARTPOD PHYS_TO_COMPATK1(0x1fc00020) -#define IP27PROM_FLASHLEDS PHYS_TO_COMPATK1(0x1fc00028) -#define IP27PROM_REPOD PHYS_TO_COMPATK1(0x1fc00030) -#define IP27PROM_LAUNCHSLAVE PHYS_TO_COMPATK1(0x1fc00038) -#define IP27PROM_WAITSLAVE PHYS_TO_COMPATK1(0x1fc00040) -#define IP27PROM_POLLSLAVE PHYS_TO_COMPATK1(0x1fc00048) - -#define KL_UART_BASE LOCAL_HUB_ADDR(MD_UREG0_0) /* base of UART regs */ -#define KL_UART_CMD LOCAL_HUB_ADDR(MD_UREG0_0) /* UART command reg */ -#define KL_UART_DATA LOCAL_HUB_ADDR(MD_UREG0_1) /* UART data reg */ -#define KL_I2C_REG MD_UREG0_0 /* I2C reg */ - -#ifndef __ASSEMBLY__ - -/* Address 0x400 to 0x1000 ualias points to cache error eframe + misc - * CACHE_ERR_SP_PTR could either contain an address to the stack, or - * the stack could start at CACHE_ERR_SP_PTR - */ -#if defined(HUB_ERR_STS_WAR) -#define CACHE_ERR_EFRAME 0x480 -#else /* HUB_ERR_STS_WAR */ -#define CACHE_ERR_EFRAME 0x400 -#endif /* HUB_ERR_STS_WAR */ - -#define CACHE_ERR_ECCFRAME (CACHE_ERR_EFRAME + EF_SIZE) -#define CACHE_ERR_SP_PTR (0x1000 - 32) /* why -32? TBD */ -#define CACHE_ERR_IBASE_PTR (0x1000 - 40) -#define CACHE_ERR_SP (CACHE_ERR_SP_PTR - 16) -#define CACHE_ERR_AREA_SIZE (ARCS_SPB_OFFSET - CACHE_ERR_EFRAME) - -#endif /* !__ASSEMBLY__ */ - -#define _ARCSPROM - -#if defined(HUB_ERR_STS_WAR) - -#define ERR_STS_WAR_REGISTER IIO_IIBUSERR -#define ERR_STS_WAR_ADDR LOCAL_HUB_ADDR(IIO_IIBUSERR) -#define ERR_STS_WAR_PHYSADDR TO_PHYS((__psunsigned_t)ERR_STS_WAR_ADDR) - /* Used to match addr in error reg. */ -#define OLD_ERR_STS_WAR_OFFSET ((MD_MEM_BANKS * MD_BANK_SIZE) - 0x100) - -#endif /* HUB_ERR_STS_WAR */ - -#endif /* _ASM_SN_SN0_ADDRS_H */ |