diff options
Diffstat (limited to 'include/linux/ethtool.h')
| -rw-r--r-- | include/linux/ethtool.h | 180 |
1 files changed, 92 insertions, 88 deletions
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h index c6e427ab65fe..45f00b61c096 100644 --- a/include/linux/ethtool.h +++ b/include/linux/ethtool.h @@ -117,99 +117,101 @@ struct ethtool_eeprom { __u8 data[0]; }; -/* for configuring coalescing parameters of chip */ +/** + * struct ethtool_coalesce - coalescing parameters for IRQs and stats updates + * @cmd: ETHTOOL_{G,S}COALESCE + * @rx_coalesce_usecs: How many usecs to delay an RX interrupt after + * a packet arrives. + * @rx_max_coalesced_frames: Maximum number of packets to receive + * before an RX interrupt. + * @rx_coalesce_usecs_irq: Same as @rx_coalesce_usecs, except that + * this value applies while an IRQ is being serviced by the host. + * @rx_max_coalesced_frames_irq: Same as @rx_max_coalesced_frames, + * except that this value applies while an IRQ is being serviced + * by the host. + * @tx_coalesce_usecs: How many usecs to delay a TX interrupt after + * a packet is sent. + * @tx_max_coalesced_frames: Maximum number of packets to be sent + * before a TX interrupt. + * @tx_coalesce_usecs_irq: Same as @tx_coalesce_usecs, except that + * this value applies while an IRQ is being serviced by the host. + * @tx_max_coalesced_frames_irq: Same as @tx_max_coalesced_frames, + * except that this value applies while an IRQ is being serviced + * by the host. + * @stats_block_coalesce_usecs: How many usecs to delay in-memory + * statistics block updates. Some drivers do not have an + * in-memory statistic block, and in such cases this value is + * ignored. This value must not be zero. + * @use_adaptive_rx_coalesce: Enable adaptive RX coalescing. + * @use_adaptive_tx_coalesce: Enable adaptive TX coalescing. + * @pkt_rate_low: Threshold for low packet rate (packets per second). + * @rx_coalesce_usecs_low: How many usecs to delay an RX interrupt after + * a packet arrives, when the packet rate is below @pkt_rate_low. + * @rx_max_coalesced_frames_low: Maximum number of packets to be received + * before an RX interrupt, when the packet rate is below @pkt_rate_low. + * @tx_coalesce_usecs_low: How many usecs to delay a TX interrupt after + * a packet is sent, when the packet rate is below @pkt_rate_low. + * @tx_max_coalesced_frames_low: Maximum nuumber of packets to be sent before + * a TX interrupt, when the packet rate is below @pkt_rate_low. + * @pkt_rate_high: Threshold for high packet rate (packets per second). + * @rx_coalesce_usecs_high: How many usecs to delay an RX interrupt after + * a packet arrives, when the packet rate is above @pkt_rate_high. + * @rx_max_coalesced_frames_high: Maximum number of packets to be received + * before an RX interrupt, when the packet rate is above @pkt_rate_high. + * @tx_coalesce_usecs_high: How many usecs to delay a TX interrupt after + * a packet is sent, when the packet rate is above @pkt_rate_high. + * @tx_max_coalesced_frames_high: Maximum number of packets to be sent before + * a TX interrupt, when the packet rate is above @pkt_rate_high. + * @rate_sample_interval: How often to do adaptive coalescing packet rate + * sampling, measured in seconds. Must not be zero. + * + * Each pair of (usecs, max_frames) fields specifies this exit + * condition for interrupt coalescing: + * (usecs > 0 && time_since_first_completion >= usecs) || + * (max_frames > 0 && completed_frames >= max_frames) + * It is illegal to set both usecs and max_frames to zero as this + * would cause interrupts to never be generated. To disable + * coalescing, set usecs = 0 and max_frames = 1. + * + * Some implementations ignore the value of max_frames and use the + * condition: + * time_since_first_completion >= usecs + * This is deprecated. Drivers for hardware that does not support + * counting completions should validate that max_frames == !rx_usecs. + * + * Adaptive RX/TX coalescing is an algorithm implemented by some + * drivers to improve latency under low packet rates and improve + * throughput under high packet rates. Some drivers only implement + * one of RX or TX adaptive coalescing. Anything not implemented by + * the driver causes these values to be silently ignored. + * + * When the packet rate is below @pkt_rate_high but above + * @pkt_rate_low (both measured in packets per second) the + * normal {rx,tx}_* coalescing parameters are used. + */ struct ethtool_coalesce { - __u32 cmd; /* ETHTOOL_{G,S}COALESCE */ - - /* How many usecs to delay an RX interrupt after - * a packet arrives. If 0, only rx_max_coalesced_frames - * is used. - */ + __u32 cmd; __u32 rx_coalesce_usecs; - - /* How many packets to delay an RX interrupt after - * a packet arrives. If 0, only rx_coalesce_usecs is - * used. It is illegal to set both usecs and max frames - * to zero as this would cause RX interrupts to never be - * generated. - */ __u32 rx_max_coalesced_frames; - - /* Same as above two parameters, except that these values - * apply while an IRQ is being serviced by the host. Not - * all cards support this feature and the values are ignored - * in that case. - */ __u32 rx_coalesce_usecs_irq; __u32 rx_max_coalesced_frames_irq; - - /* How many usecs to delay a TX interrupt after - * a packet is sent. If 0, only tx_max_coalesced_frames - * is used. - */ __u32 tx_coalesce_usecs; - - /* How many packets to delay a TX interrupt after - * a packet is sent. If 0, only tx_coalesce_usecs is - * used. It is illegal to set both usecs and max frames - * to zero as this would cause TX interrupts to never be - * generated. - */ __u32 tx_max_coalesced_frames; - - /* Same as above two parameters, except that these values - * apply while an IRQ is being serviced by the host. Not - * all cards support this feature and the values are ignored - * in that case. - */ __u32 tx_coalesce_usecs_irq; __u32 tx_max_coalesced_frames_irq; - - /* How many usecs to delay in-memory statistics - * block updates. Some drivers do not have an in-memory - * statistic block, and in such cases this value is ignored. - * This value must not be zero. - */ __u32 stats_block_coalesce_usecs; - - /* Adaptive RX/TX coalescing is an algorithm implemented by - * some drivers to improve latency under low packet rates and - * improve throughput under high packet rates. Some drivers - * only implement one of RX or TX adaptive coalescing. Anything - * not implemented by the driver causes these values to be - * silently ignored. - */ __u32 use_adaptive_rx_coalesce; __u32 use_adaptive_tx_coalesce; - - /* When the packet rate (measured in packets per second) - * is below pkt_rate_low, the {rx,tx}_*_low parameters are - * used. - */ __u32 pkt_rate_low; __u32 rx_coalesce_usecs_low; __u32 rx_max_coalesced_frames_low; __u32 tx_coalesce_usecs_low; __u32 tx_max_coalesced_frames_low; - - /* When the packet rate is below pkt_rate_high but above - * pkt_rate_low (both measured in packets per second) the - * normal {rx,tx}_* coalescing parameters are used. - */ - - /* When the packet rate is (measured in packets per second) - * is above pkt_rate_high, the {rx,tx}_*_high parameters are - * used. - */ __u32 pkt_rate_high; __u32 rx_coalesce_usecs_high; __u32 rx_max_coalesced_frames_high; __u32 tx_coalesce_usecs_high; __u32 tx_max_coalesced_frames_high; - - /* How often to do adaptive coalescing packet rate sampling, - * measured in seconds. Must not be zero. - */ __u32 rate_sample_interval; }; @@ -444,7 +446,7 @@ struct ethtool_flow_ext { }; /** - * struct ethtool_rx_flow_spec - specification for RX flow filter + * struct ethtool_rx_flow_spec - classification rule for RX flows * @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW * @h_u: Flow fields to match (dependent on @flow_type) * @h_ext: Additional fields to match @@ -454,7 +456,9 @@ struct ethtool_flow_ext { * includes the %FLOW_EXT flag. * @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC * if packets should be discarded - * @location: Index of filter in hardware table + * @location: Location of rule in the table. Locations must be + * numbered such that a flow matching multiple rules will be + * classified according to the first (lowest numbered) rule. */ struct ethtool_rx_flow_spec { __u32 flow_type; @@ -473,9 +477,9 @@ struct ethtool_rx_flow_spec { * %ETHTOOL_GRXCLSRLALL, %ETHTOOL_SRXCLSRLDEL or %ETHTOOL_SRXCLSRLINS * @flow_type: Type of flow to be affected, e.g. %TCP_V4_FLOW * @data: Command-dependent value - * @fs: Flow filter specification + * @fs: Flow classification rule * @rule_cnt: Number of rules to be affected - * @rule_locs: Array of valid rule indices + * @rule_locs: Array of used rule locations * * For %ETHTOOL_GRXFH and %ETHTOOL_SRXFH, @data is a bitmask indicating * the fields included in the flow hash, e.g. %RXH_IP_SRC. The following @@ -487,23 +491,20 @@ struct ethtool_rx_flow_spec { * For %ETHTOOL_GRXCLSRLCNT, @rule_cnt is set to the number of defined * rules on return. * - * For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the index of an - * existing filter rule on entry and @fs contains the rule on return. + * For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the location of an + * existing rule on entry and @fs contains the rule on return. * * For %ETHTOOL_GRXCLSRLALL, @rule_cnt specifies the array size of the * user buffer for @rule_locs on entry. On return, @data is the size - * of the filter table and @rule_locs contains the indices of the - * defined rules. + * of the rule table, @rule_cnt is the number of defined rules, and + * @rule_locs contains the locations of the defined rules. Drivers + * must use the second parameter to get_rxnfc() instead of @rule_locs. * - * For %ETHTOOL_SRXCLSRLINS, @fs specifies the filter rule to add or - * update. @fs.@location specifies the index to use and must not be - * ignored. + * For %ETHTOOL_SRXCLSRLINS, @fs specifies the rule to add or update. + * @fs.@location specifies the location to use and must not be ignored. * - * For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the index of an - * existing filter rule on entry. - * - * Implementation of indexed classification rules generally requires a - * TCAM. + * For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the location of an + * existing rule on entry. */ struct ethtool_rxnfc { __u32 cmd; @@ -726,6 +727,9 @@ enum ethtool_sfeatures_retval_bits { /* needed by dev_disable_lro() */ extern int __ethtool_set_flags(struct net_device *dev, u32 flags); +extern int __ethtool_get_settings(struct net_device *dev, + struct ethtool_cmd *cmd); + /** * enum ethtool_phys_id_state - indicator state for physical identification * @ETHTOOL_ID_INACTIVE: Physical ID indicator should be deactivated @@ -936,7 +940,7 @@ struct ethtool_ops { int (*set_priv_flags)(struct net_device *, u32); int (*get_sset_count)(struct net_device *, int); int (*get_rxnfc)(struct net_device *, - struct ethtool_rxnfc *, void *); + struct ethtool_rxnfc *, u32 *rule_locs); int (*set_rxnfc)(struct net_device *, struct ethtool_rxnfc *); int (*flash_device)(struct net_device *, struct ethtool_flash *); int (*reset)(struct net_device *, u32 *); |