diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/nl80211.h | 8 | ||||
| -rw-r--r-- | include/net/cfg80211.h | 38 |
2 files changed, 37 insertions, 9 deletions
diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h index 9e541452d805..410a06ea551b 100644 --- a/include/linux/nl80211.h +++ b/include/linux/nl80211.h @@ -394,6 +394,11 @@ * * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. * + * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial + * mesh config parameters may be given. + * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the + * network is determined by the network interface. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -500,6 +505,9 @@ enum nl80211_commands { NL80211_CMD_FRAME_WAIT_CANCEL, + NL80211_CMD_JOIN_MESH, + NL80211_CMD_LEAVE_MESH, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 902895dfbd49..788c3989a9e8 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -258,13 +258,9 @@ struct ieee80211_supported_band { /** * struct vif_params - describes virtual interface parameters - * @mesh_id: mesh ID to use - * @mesh_id_len: length of the mesh ID * @use_4addr: use 4-address frames */ struct vif_params { - u8 *mesh_id; - int mesh_id_len; int use_4addr; }; @@ -615,6 +611,11 @@ struct bss_parameters { int ap_isolate; }; +/* + * struct mesh_config - 802.11s mesh configuration + * + * These parameters can be changed while the mesh is active. + */ struct mesh_config { /* Timeouts in ms */ /* Mesh plink management parameters */ @@ -638,6 +639,18 @@ struct mesh_config { }; /** + * struct mesh_setup - 802.11s mesh setup configuration + * @mesh_id: the mesh ID + * @mesh_id_len: length of the mesh ID, at least 1 and at most 32 bytes + * + * These parameters are fixed when the mesh is created. + */ +struct mesh_setup { + const u8 *mesh_id; + u8 mesh_id_len; +}; + +/** * struct ieee80211_txq_params - TX queue parameters * @queue: TX queue identifier (NL80211_TXQ_Q_*) * @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled @@ -1078,7 +1091,7 @@ struct cfg80211_pmksa { * * @get_mesh_params: Put the current mesh parameters into *params * - * @set_mesh_params: Set mesh parameters. + * @update_mesh_params: Update mesh parameters on a running mesh. * The mask is a bitfield which tells us which parameters to * set, and which to leave alone. * @@ -1229,9 +1242,14 @@ struct cfg80211_ops { int (*get_mesh_params)(struct wiphy *wiphy, struct net_device *dev, struct mesh_config *conf); - int (*set_mesh_params)(struct wiphy *wiphy, - struct net_device *dev, - const struct mesh_config *nconf, u32 mask); + int (*update_mesh_params)(struct wiphy *wiphy, + struct net_device *dev, u32 mask, + const struct mesh_config *nconf); + int (*join_mesh)(struct wiphy *wiphy, struct net_device *dev, + const struct mesh_config *conf, + const struct mesh_setup *setup); + int (*leave_mesh)(struct wiphy *wiphy, struct net_device *dev); + int (*change_bss)(struct wiphy *wiphy, struct net_device *dev, struct bss_parameters *params); @@ -1647,6 +1665,8 @@ struct cfg80211_cached_keys; * @bssid: (private) Used by the internal configuration code * @ssid: (private) Used by the internal configuration code * @ssid_len: (private) Used by the internal configuration code + * @mesh_id_len: (private) Used by the internal configuration code + * @mesh_id_up_len: (private) Used by the internal configuration code * @wext: (private) Used by the internal wireless extensions compat code * @use_4addr: indicates 4addr mode is used on this interface, must be * set by driver (if supported) on add_interface BEFORE registering the @@ -1676,7 +1696,7 @@ struct wireless_dev { /* currently used for IBSS and SME - might be rearranged later */ u8 ssid[IEEE80211_MAX_SSID_LEN]; - u8 ssid_len; + u8 ssid_len, mesh_id_len, mesh_id_up_len; enum { CFG80211_SME_IDLE, CFG80211_SME_CONNECTING, |