diff options
Diffstat (limited to 'lib/Kconfig.kcsan')
| -rw-r--r-- | lib/Kconfig.kcsan | 118 |
1 files changed, 118 insertions, 0 deletions
diff --git a/lib/Kconfig.kcsan b/lib/Kconfig.kcsan new file mode 100644 index 000000000000..5dd464e52ab4 --- /dev/null +++ b/lib/Kconfig.kcsan @@ -0,0 +1,118 @@ +# SPDX-License-Identifier: GPL-2.0-only + +config HAVE_ARCH_KCSAN + bool + +menuconfig KCSAN + bool "KCSAN: watchpoint-based dynamic data race detector" + depends on HAVE_ARCH_KCSAN && !KASAN && STACKTRACE + default n + help + Kernel Concurrency Sanitizer is a dynamic data race detector, which + uses a watchpoint-based sampling approach to detect races. See + <file:Documentation/dev-tools/kcsan.rst> for more details. + +if KCSAN + +config KCSAN_DEBUG + bool "Debugging of KCSAN internals" + default n + +config KCSAN_SELFTEST + bool "Perform short selftests on boot" + default y + help + Run KCSAN selftests on boot. On test failure, causes kernel to panic. + +config KCSAN_EARLY_ENABLE + bool "Early enable during boot" + default y + help + If KCSAN should be enabled globally as soon as possible. KCSAN can + later be enabled/disabled via debugfs. + +config KCSAN_NUM_WATCHPOINTS + int "Number of available watchpoints" + default 64 + help + Total number of available watchpoints. An address range maps into a + specific watchpoint slot as specified in kernel/kcsan/encoding.h. + Although larger number of watchpoints may not be usable due to + limited number of CPUs, a larger value helps to improve performance + due to reducing cache-line contention. The chosen default is a + conservative value; we should almost never observe "no_capacity" + events (see /sys/kernel/debug/kcsan). + +config KCSAN_UDELAY_TASK + int "Delay in microseconds (for tasks)" + default 80 + help + For tasks, the microsecond delay after setting up a watchpoint. + +config KCSAN_UDELAY_INTERRUPT + int "Delay in microseconds (for interrupts)" + default 20 + help + For interrupts, the microsecond delay after setting up a watchpoint. + Interrupts have tighter latency requirements, and their delay should + be lower than for tasks. + +config KCSAN_DELAY_RANDOMIZE + bool "Randomize above delays" + default y + help + If delays should be randomized, where the maximum is KCSAN_UDELAY_*. + If false, the chosen delays are always KCSAN_UDELAY_* defined above. + +config KCSAN_SKIP_WATCH + int "Skip instructions before setting up watchpoint" + default 4000 + help + The number of per-CPU memory operations to skip, before another + watchpoint is set up, i.e. one in KCSAN_WATCH_SKIP per-CPU + memory operations are used to set up a watchpoint. A smaller value + results in more aggressive race detection, whereas a larger value + improves system performance at the cost of missing some races. + +config KCSAN_SKIP_WATCH_RANDOMIZE + bool "Randomize watchpoint instruction skip count" + default y + help + If instruction skip count should be randomized, where the maximum is + KCSAN_WATCH_SKIP. If false, the chosen value is always + KCSAN_WATCH_SKIP. + +# Note that, while some of the below options could be turned into boot +# parameters, to optimize for the common use-case, we avoid this because: (a) +# it would impact performance (and we want to avoid static branch for all +# {READ,WRITE}_ONCE, atomic_*, bitops, etc.), and (b) complicate the design +# without real benefit. The main purpose of the below options are for use in +# fuzzer configs to control reported data races, and are not expected to be +# switched frequently by a user. + +config KCSAN_REPORT_RACE_UNKNOWN_ORIGIN + bool "Report races of unknown origin" + default y + help + If KCSAN should report races where only one access is known, and the + conflicting access is of unknown origin. This type of race is + reported if it was only possible to infer a race due to a data value + change while an access is being delayed on a watchpoint. + +config KCSAN_REPORT_VALUE_CHANGE_ONLY + bool "Only report races where watcher observed a data value change" + default y + help + If enabled and a conflicting write is observed via watchpoint, but + the data value of the memory location was observed to remain + unchanged, do not report the data race. + +config KCSAN_IGNORE_ATOMICS + bool "Do not instrument marked atomic accesses" + default n + help + If enabled, never instruments marked atomic accesses. This results in + not reporting data races where one access is atomic and the other is + a plain access. + +endif # KCSAN |