summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* net:drivers/net: Miscellaneous conversions to ETH_ALENJoe Perches2013-10-0257-149/+146
| | | | | | | | | | | | Convert the memset/memcpy uses of 6 to ETH_ALEN where appropriate. Also convert some struct definitions and u8 array declarations of [6] to ETH_ALEN. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* include/linux/skbuff.h: move CONFIG_XFRM check inside the skb_sec_path()Denis Kirjanov2013-10-021-5/+2
| | | | | | | And thus we have only one function definition Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* tcp: sndbuf autotuning improvementsEric Dumazet2013-10-022-14/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | tcp_fixup_sndbuf() is underestimating initial send buffer requirements. It was not noticed because big GSO packets were escaping the limitation, but with smaller TSO packets (or TSO/GSO/SG off), application hits sk_sndbuf before having a chance to fill enough packets in socket write queue. - initial cwnd can be bigger than 10 for specific routes - SKB_TRUESIZE() is a bit under real needs in some cases, because of power-of-two rounding in kmalloc() - Fast Recovery (RFC 5681 3.2) : Cubic needs 70% factor - Extra cushion (application might react slowly to POLLOUT) tcp_v4_conn_req_fastopen() needs to call tcp_init_metrics() before calling tcp_init_buffer_space() Then we realize tcp_new_space() should call tcp_fixup_sndbuf() instead of duplicating this stuff. Rename tcp_fixup_sndbuf() to tcp_sndbuf_expand() to be more descriptive. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* fib_trie: avoid a redundant bit judgement in inflatebaker.zhang2013-10-021-6/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Because 'node' is the i'st child of 'oldnode', thus, here 'i' equals tkey_extract_bits(node->key, oldtnode->pos, oldtnode->bits) we just get 1 more bit, and need not care the detail value of this bits. I apologize for the mistake. I generated the patch on a branch version, and did not notice the put_child has been changed. I have redone the test on HEAD version with my patch. two cases are used. case 1. inflate a node which has a leaf child node. case 2: inflate a node which has a an child node with skipped bits test env: ip link set eth0 up ip a add dev eth0 192.168.11.1/32 here, we just focus on route table(MAIN), so I use a "192.168.11.1/32" address to simplify the test case. call trace: + fib_insert_node + + trie_rebalance + + + resize + + + + inflate Test case 1: inflate a node which has a leaf child node. =========================================================== step 1. prepare a fib trie ------------------------------------------ ip r a 192.168.0.0/24 via 192.168.11.1 ip r a 192.168.1.0/24 via 192.168.11.1 we get a fib trie. root@baker:~# cat /proc/net/fib_trie Main: +-- 192.168.0.0/23 1 0 0 |-- 192.168.0.0 /24 universe UNICAST |-- 192.168.1.0 /24 universe UNICAST Local: ..... step 2. Add the third route ------------------------------------------ root@baker:~# ip r a 192.168.2.0/24 via 192.168.11.1 A fib_trie leaf will be inserted in fib_insert_node before trie_rebalance. For function 'inflate': 'inflate' is called with following trie. +-- 192.168.0.0/22 1 1 0 <=== tn node +-- 192.168.0.0/23 1 0 0 <== node a |-- 192.168.0.0 /24 universe UNICAST |-- 192.168.1.0 /24 universe UNICAST |-- 192.168.2.0 <== leaf(node b) When process node b, which is a leaf. here: i is 1, node key "192.168.2.0" oldnode is (pos:22, bits:1) unpatch source: tkey_extract_bits(node->key, oldtnode->pos + oldtnode->bits, 1) it equals: tkey_extract_bits("192.168,2,0", 22 + 1, 1) thus got 0, and call put_child(tn, 2*i, node); <== 2*i=2. patched source: tkey_extract_bits(node->key, oldtnode->pos, oldtnode->bits + 1), tkey_extract_bits("192.168,2,0", 22, 1 + 1) <== get 2. Test case 2: inflate a node which has a an child node with skipped bits ========================================================================== step 1. prepare a fib trie. ip link set eth0 up ip a add dev eth0 192.168.11.1/32 ip r a 192.168.128.0/24 via 192.168.11.1 ip r a 192.168.0.0/24 via 192.168.11.1 ip r a 192.168.16.0/24 via 192.168.11.1 ip r a 192.168.32.0/24 via 192.168.11.1 ip r a 192.168.48.0/24 via 192.168.11.1 ip r a 192.168.144.0/24 via 192.168.11.1 ip r a 192.168.160.0/24 via 192.168.11.1 ip r a 192.168.176.0/24 via 192.168.11.1 check: root@baker:~# cat /proc/net/fib_trie Main: +-- 192.168.0.0/16 1 0 0 +-- 192.168.0.0/18 2 0 0 |-- 192.168.0.0 /24 universe UNICAST |-- 192.168.16.0 /24 universe UNICAST |-- 192.168.32.0 /24 universe UNICAST |-- 192.168.48.0 /24 universe UNICAST +-- 192.168.128.0/18 2 0 0 |-- 192.168.128.0 /24 universe UNICAST |-- 192.168.144.0 /24 universe UNICAST |-- 192.168.160.0 /24 universe UNICAST |-- 192.168.176.0 /24 universe UNICAST Local: ... step 2. add a route to trigger inflate. ip r a 192.168.96.0/24 via 192.168.11.1 This command will call serveral times inflate. In the first time, the fib_trie is: ________________________ +-- 192.168.128.0/(16, 1) <== tn node +-- 192.168.0.0/(17, 1) <== node a +-- 192.168.0.0/(18, 2) |-- 192.168.0.0 |-- 192.168.16.0 |-- 192.168.32.0 |-- 192.168.48.0 |-- 192.168.96.0 +-- 192.168.128.0/(18, 2) <== node b. |-- 192.168.128.0 |-- 192.168.144.0 |-- 192.168.160.0 |-- 192.168.176.0 NOTE: node b is a interal node with skipped bits. here, i:1, node->key "192.168.128.0", oldnode:(pos:16, bits:1) so tkey_extract_bits(node->key, oldtnode->pos + oldtnode->bits, 1) it equals: tkey_extract_bits("192.168,128,0", 16 + 1, 1) <=== 0 tkey_extract_bits(node->key, oldtnode->pos, oldtnode->bits, 1) it equals: tkey_extract_bits("192.168,128,0", 16, 1+1) <=== 2 2*i + 0 == 2, so the result is same. Signed-off-by: baker.zhang <baker.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* isdn: eicon: free pointer after using it in log msg in ↵Jesper Juhl2013-10-021-1/+1
| | | | | | | | | | | | divas_um_idi_delete_entity() Not really a problem, but nice IMHO; the Coverity static analyzer complains that we use the pointer 'e' after it has been freed, so move the freeing below the final use, even if that use is just using the value of the pointer and not actually dereferencing it. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* xen-netfront: convert to GRO APIWei Liu2013-10-021-1/+3
| | | | | | | | | | | | | Anirban was seeing netfront received MTU size packets, which downgraded throughput. The following patch makes netfront use GRO API which improves throughput for that case. Signed-off-by: Wei Liu <wei.liu2@citrix.com> Cc: Anirban Chakraborty <abchak@juniper.net> Cc: Ian Campbell <ian.campbell@citrix.com> Acked-by: Konrad Wilk <konrad.wilk@oracle.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tg3: use phylib when robo switch is in useHauke Mehrtens2013-10-021-1/+10
| | | | | | | | | When a switch is connected as a PHY to the MAC driven by tg3, use phylib and provide the phy address to tg3 from the sprom. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ssb: provide phy address for Gigabit Ethernet driverHauke Mehrtens2013-10-021-0/+14
| | | | | | | | | Add a function to provide the phy address which should be used to the Gigabit Ethernet driver connected to ssb. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tg3: add support a phy at an address different than 01Hauke Mehrtens2013-10-021-19/+19
| | | | | | | | | | | | | | | When phylib was in use tg3 only searched at address 01 on the mdio bus and did not work with any other address. On the BCM4705 SoCs the switch is connected as a PHY behind the MAC driven by tg3 and it is at PHY address 30 in most cases. This is a preparation patch to allow support for such switches. phy_addr is set to TG3_PHY_MII_ADDR for all devices, which are using phylib, so this should not change any behavior. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2013-10-01533-3021/+5170
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/ethernet/emulex/benet/be.h drivers/net/usb/qmi_wwan.c drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h include/net/netfilter/nf_conntrack_synproxy.h include/net/secure_seq.h The conflicts are of two varieties: 1) Conflicts with Joe Perches's 'extern' removal from header file function declarations. Usually it's an argument signature change or a function being added/removed. The resolutions are trivial. 2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds a new value, another changes an existing value. That sort of thing. Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds2013-10-01107-845/+1301
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking changes from David Miller: 1) Multiply in netfilter IPVS can overflow when calculating destination weight. From Simon Kirby. 2) Use after free fixes in IPVS from Julian Anastasov. 3) SFC driver bug fixes from Daniel Pieczko. 4) Memory leak in pcan_usb_core failure paths, from Alexey Khoroshilov. 5) Locking and encapsulation fixes to serial line CAN driver, from Andrew Naujoks. 6) Duplex and VF handling fixes to bnx2x driver from Yaniv Rosner, Eilon Greenstein, and Ariel Elior. 7) In lapb, if no other packets are outstanding, T1 timeouts actually stall things and no packet gets sent. Fix from Josselin Costanzi. 8) ICMP redirects should not make it to the socket error queues, from Duan Jiong. 9) Fix bugs in skge DMA mapping error handling, from Nikulas Patocka. 10) Fix setting of VLAN priority field on via-rhine driver, from Roget Luethi. 11) Fix TX stalls and VLAN promisc programming in be2net driver from Ajit Khaparde. 12) Packet padding doesn't get handled correctly in new usbnet SG support code, from Ming Lei. 13) Fix races in netdevice teardown wrt. network namespace closing. From Eric W. Biederman. 14) Fix potential missed initialization of net_secret if not TCP connections are openned. From Eric Dumazet. 15) Cinterion PLXX product ID in qmi_wwan driver is wrong, from Aleksander Morgado. 16) skb_cow_head() can change skb->data and thus packet header pointers, don't use stale ip_hdr reference in ip_tunnel code. 17) Backend state transition handling fixes in xen-netback, from Paul Durrant. 18) Packet offset for AH protocol is handled wrong in flow dissector, from Eric Dumazet. 19) Taking down an fq packet scheduler instance can leave stale packets in the queues, fix from Eric Dumazet. 20) Fix performance regressions introduced by TCP Small Queues. From Eric Dumazet. 21) IPV6 GRE tunneling code calculates max_headroom incorrectly, from Hannes Frederic Sowa. 22) Multicast timer handlers in ipv4 and ipv6 can be the last and final reference to the ipv4/ipv6 specific network device state, so use the reference put that will check and release the object if the reference hits zero. From Salam Noureddine. 23) Fix memory corruption in ip_tunnel driver, and use skb_push() instead of __skb_push() so that similar bugs are less hard to find. From Steffen Klassert. 24) Add forgotten hookup of rtnl_ops in SIT and ip6tnl drivers, from Nicolas Dichtel. 25) fq scheduler doesn't accurately rate limit in certain circumstances, from Eric Dumazet. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits) pkt_sched: fq: rate limiting improvements ip6tnl: allow to use rtnl ops on fb tunnel sit: allow to use rtnl ops on fb tunnel ip_tunnel: Remove double unregister of the fallback device ip_tunnel_core: Change __skb_push back to skb_push ip_tunnel: Add fallback tunnels to the hash lists ip_tunnel: Fix a memory corruption in ip_tunnel_xmit qlcnic: Fix SR-IOV configuration ll_temac: Reset dma descriptors indexes on ndo_open skbuff: size of hole is wrong in a comment ipv6 mcast: use in6_dev_put in timer handlers instead of __in6_dev_put ipv4 igmp: use in_dev_put in timer handlers instead of __in_dev_put ethernet: moxa: fix incorrect placement of __initdata tag ipv6: gre: correct calculation of max_headroom powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file Revert "powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file" bonding: Fix broken promiscuity reference counting issue tcp: TSQ can use a dynamic limit dm9601: fix IFF_ALLMULTI handling pkt_sched: fq: qdisc dismantle fixes ...
| | * pkt_sched: fq: rate limiting improvementsEric Dumazet2013-10-011-19/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FQ rate limiting suffers from two problems, reported by Steinar : 1) FQ enforces a delay when flow quantum is exhausted in order to reduce cpu overhead. But if packets are small, current delay computation is slightly wrong, and observed rates can be too high. Steinar had this problem because he disabled TSO and GSO, and default FQ quantum is 2*1514. (Of course, I wish recent TSO auto sizing changes will help to not having to disable TSO in the first place) 2) maxrate was not used for forwarded flows (skbs not attached to a socket) Tested: tc qdisc add dev eth0 root est 1sec 4sec fq maxrate 8Mbit netperf -H lpq84 -l 1000 & sleep 10 ; tc -s qdisc show dev eth0 qdisc fq 8003: root refcnt 32 limit 10000p flow_limit 100p buckets 1024 quantum 3028 initial_quantum 15140 maxrate 8000Kbit Sent 16819357 bytes 11258 pkt (dropped 0, overlimits 0 requeues 0) rate 7831Kbit 653pps backlog 7570b 5p requeues 0 44 flows (43 inactive, 1 throttled), next packet delay 2977352 ns 0 gc, 0 highprio, 5545 throttled lpq83:~# tcpdump -p -i eth0 host lpq84 -c 12 09:02:52.079484 IP lpq83 > lpq84: . 1389536928:1389538376(1448) ack 3808678021 win 457 <nop,nop,timestamp 961812 572609068> 09:02:52.079499 IP lpq83 > lpq84: . 1448:2896(1448) ack 1 win 457 <nop,nop,timestamp 961812 572609068> 09:02:52.079906 IP lpq84 > lpq83: . ack 2896 win 16384 <nop,nop,timestamp 572609080 961812> 09:02:52.082568 IP lpq83 > lpq84: . 2896:4344(1448) ack 1 win 457 <nop,nop,timestamp 961815 572609071> 09:02:52.082581 IP lpq83 > lpq84: . 4344:5792(1448) ack 1 win 457 <nop,nop,timestamp 961815 572609071> 09:02:52.083017 IP lpq84 > lpq83: . ack 5792 win 16384 <nop,nop,timestamp 572609083 961815> 09:02:52.085678 IP lpq83 > lpq84: . 5792:7240(1448) ack 1 win 457 <nop,nop,timestamp 961818 572609074> 09:02:52.085693 IP lpq83 > lpq84: . 7240:8688(1448) ack 1 win 457 <nop,nop,timestamp 961818 572609074> 09:02:52.086117 IP lpq84 > lpq83: . ack 8688 win 16384 <nop,nop,timestamp 572609086 961818> 09:02:52.088792 IP lpq83 > lpq84: . 8688:10136(1448) ack 1 win 457 <nop,nop,timestamp 961821 572609077> 09:02:52.088806 IP lpq83 > lpq84: . 10136:11584(1448) ack 1 win 457 <nop,nop,timestamp 961821 572609077> 09:02:52.089217 IP lpq84 > lpq83: . ack 11584 win 16384 <nop,nop,timestamp 572609090 961821> Reported-by: Steinar H. Gunderson <sesse@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * ip6tnl: allow to use rtnl ops on fb tunnelNicolas Dichtel2013-10-011-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | rtnl ops where introduced by c075b13098b3 ("ip6tnl: advertise tunnel param via rtnl"), but I forget to assign rtnl ops to fb tunnels. Now that it is done, we must remove the explicit call to unregister_netdevice_queue(), because the fallback tunnel is added to the queue in ip6_tnl_destroy_tunnels() when checking rtnl_link_ops of all netdevices (this is valid since commit 0bd8762824e7 ("ip6tnl: add x-netns support")). Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * sit: allow to use rtnl ops on fb tunnelNicolas Dichtel2013-10-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | rtnl ops where introduced by ba3e3f50a0e5 ("sit: advertise tunnel param via rtnl"), but I forget to assign rtnl ops to fb tunnels. Now that it is done, we must remove the explicit call to unregister_netdevice_queue(), because the fallback tunnel is added to the queue in sit_destroy_tunnels() when checking rtnl_link_ops of all netdevices (this is valid since commit 5e6700b3bf98 ("sit: add support of x-netns")). Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * Merge branch 'ip_tunnel'David S. Miller2013-10-012-10/+10
| | |\ | | | | | | | | | | | | | | | | | | | | ip_tunnel bug fixes from Steffen Klassert. Signed-off-by: David S. Miller <davem@davemloft.net>
| | | * ip_tunnel: Remove double unregister of the fallback deviceSteffen Klassert2013-10-011-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When queueing the netdevices for removal, we queue the fallback device twice in ip_tunnel_destroy(). The first time when we queue all netdevices in the namespace and then again explicitly. Fix this by removing the explicit queueing of the fallback device. Bug was introduced when network namespace support was added with commit 6c742e714d8 ("ipip: add x-netns support"). Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | | * ip_tunnel_core: Change __skb_push back to skb_pushSteffen Klassert2013-10-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Git commit 0e6fbc5b ("ip_tunnels: extend iptunnel_xmit()") moved the IP header installation to iptunnel_xmit() and changed skb_push() to __skb_push(). This makes possible bugs hard to track down, so change it back to skb_push(). Cc: Pravin Shelar <pshelar@nicira.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | | * ip_tunnel: Add fallback tunnels to the hash listsSteffen Klassert2013-10-011-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently we can not update the tunnel parameters of the fallback tunnels because we don't find them in the hash lists. Fix this by adding them on initialization. Bug was introduced with commit c544193214 ("GRE: Refactor GRE tunneling code.") Cc: Pravin Shelar <pshelar@nicira.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | | * ip_tunnel: Fix a memory corruption in ip_tunnel_xmitSteffen Klassert2013-10-011-6/+6
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We might extend the used aera of a skb beyond the total headroom when we install the ipip header. Fix this by calling skb_cow_head() unconditionally. Bug was introduced with commit c544193214 ("GRE: Refactor GRE tunneling code.") Cc: Pravin Shelar <pshelar@nicira.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller2013-10-0113-158/+143
| | |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pablo Neira Ayuso says: ==================== The following patchset contains Netfilter/IPVS fixes for your net tree, they are: * Fix BUG_ON splat due to malformed TCP packets seen by synproxy, from Patrick McHardy. * Fix possible weight overflow in lblc and lblcr schedulers due to 32-bits arithmetics, from Simon Kirby. * Fix possible memory access race in the lblc and lblcr schedulers, introduced when it was converted to use RCU, two patches from Julian Anastasov. * Fix hard dependency on CPU 0 when reading per-cpu stats in the rate estimator, from Julian Anastasov. * Fix race that may lead to object use after release, when invoking ipvsadm -C && ipvsadm -R, introduced when adding RCU, from Julian Anastasov. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| | | * netfilter: synproxy: fix BUG_ON triggered by corrupt TCP packetsPatrick McHardy2013-09-304-12/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TCP packets hitting the SYN proxy through the SYNPROXY target are not validated by TCP conntrack. When th->doff is below 5, an underflow happens when calculating the options length, causing skb_header_pointer() to return NULL and triggering the BUG_ON(). Handle this case gracefully by checking for NULL instead of using BUG_ON(). Reported-by: Martin Topholm <mph@one.com> Tested-by: Martin Topholm <mph@one.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
| | | * ipvs: stats should not depend on CPU 0Julian Anastasov2013-09-181-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When reading percpu stats we need to properly reset the sum when CPU 0 is not present in the possible mask. Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au>
| | | * ipvs: do not use dest after ip_vs_dest_put in LBLCRJulian Anastasov2013-09-181-30/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit c5549571f975ab ("ipvs: convert lblcr scheduler to rcu") allows RCU readers to use dest after calling ip_vs_dest_put(). In the corner case it can race with ip_vs_dest_trash_expire() which can release the dest while it is being returned to the RCU readers as scheduling result. To fix the problem do not allow e->dest to be replaced and defer the ip_vs_dest_put() call by using RCU callback. Now e->dest does not need to be RCU pointer. Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au>
| | | * ipvs: do not use dest after ip_vs_dest_put in LBLCJulian Anastasov2013-09-181-37/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit c2a4ffb70eef39 ("ipvs: convert lblc scheduler to rcu") allows RCU readers to use dest after calling ip_vs_dest_put(). In the corner case it can race with ip_vs_dest_trash_expire() which can release the dest while it is being returned to the RCU readers as scheduling result. To fix the problem do not allow en->dest to be replaced and defer the ip_vs_dest_put() call by using RCU callback. Now en->dest does not need to be RCU pointer. Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au>
| | | * ipvs: make the service replacement more robustJulian Anastasov2013-09-183-58/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 578bc3ef1e473a ("ipvs: reorganize dest trash") added IP_VS_DEST_STATE_REMOVING flag and RCU callback named ip_vs_dest_wait_readers() to keep dests and services after removal for at least a RCU grace period. But we have the following corner cases: - we can not reuse the same dest if its service is removed while IP_VS_DEST_STATE_REMOVING is still set because another dest removal in the first grace period can not extend this period. It can happen when ipvsadm -C && ipvsadm -R is used. - dest->svc can be replaced but ip_vs_in_stats() and ip_vs_out_stats() have no explicit read memory barriers when accessing dest->svc. It can happen that dest->svc was just freed (replaced) while we use it to update the stats. We solve the problems as follows: - IP_VS_DEST_STATE_REMOVING is removed and we ensure a fixed idle period for the dest (IP_VS_DEST_TRASH_PERIOD). idle_start will remember when for first time after deletion we noticed dest->refcnt=0. Later, the connections can grab a reference while in RCU grace period but if refcnt becomes 0 we can safely free the dest and its svc. - dest->svc becomes RCU pointer. As result, we add explicit RCU locking in ip_vs_in_stats() and ip_vs_out_stats(). - __ip_vs_unbind_svc is renamed to __ip_vs_svc_put(), it now can free the service immediately or after a RCU grace period. dest->svc is not set to NULL anymore. As result, unlinked dests and their services are freed always after IP_VS_DEST_TRASH_PERIOD period, unused services are freed after a RCU grace period. Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au>
| | | * ipvs: fix overflow on dest weight multiplySimon Kirby2013-09-186-20/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Schedulers such as lblc and lblcr require the weight to be as high as the maximum number of active connections. In commit b552f7e3a9524abcbcdf ("ipvs: unify the formula to estimate the overhead of processing connections"), the consideration of inactconns and activeconns was cleaned up to always count activeconns as 256 times more important than inactconns. In cases where 3000 or more connections are expected, a weight of 3000 * 256 * 3000 connections overflows the 32-bit signed result used to determine if rescheduling is required. On amd64, this merely changes the multiply and comparison instructions to 64-bit. On x86, a 64-bit result is already present from imull, so only a few more comparison instructions are emitted. Signed-off-by: Simon Kirby <sim@hostway.ca> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au>
| | * | qlcnic: Fix SR-IOV configurationManish Chopra2013-10-011-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | o Interface needs to be brought down and up while configuring SR-IOV. Protect interface up/down using rtnl_lock()/rtnl_unlock() Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | ll_temac: Reset dma descriptors indexes on ndo_openRicardo Ribalda2013-10-011-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The dma descriptors indexes are only initialized on the probe function. If a packet is on the buffer when temac_stop is called, the dma descriptors indexes can be left on a incorrect state where no other package can be sent. So an interface could be left in an usable state after ifdow/ifup. This patch makes sure that the descriptors indexes are in a proper status when the device is open. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | skbuff: size of hole is wrong in a commentNicolas Dichtel2013-09-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit c93bdd0e03e8 ("netvm: allow skb allocation to use PFMEMALLOC reserves"), hole size is one bit less than what is written in the comment. Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | Merge branch 'fixes-for-3.12' of git://gitorious.org/linux-can/linux-canDavid S. Miller2013-09-301-12/+0
| | |\ \ | | | | | | | | | | | | | | | Signed-off-by: David S. Miller <davem@davemloft.net>
| | | * | can: flexcan: fix flexcan_chip_start() on imx6Marc Kleine-Budde2013-09-301-12/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the flexcan_chip_start() function first the flexcan core is going through the soft reset sequence, then the RX FIFO is enabled. With the hardware is put into FIFO mode, message buffers 1...7 are reserved by the FIFO engine. The remaining message buffers are in reset default values. This patch removes the bogus initialization of the message buffers, as it causes an imprecise external abort on imx6. Cc: linux-stable <stable@vger.kernel.org> Reported-by: Lothar Waßmann <LW@KARO-electronics.de> Tested-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
| | * | | ipv6 mcast: use in6_dev_put in timer handlers instead of __in6_dev_putSalam Noureddine2013-09-301-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is possible for the timer handlers to run after the call to ipv6_mc_down so use in6_dev_put instead of __in6_dev_put in the handler function in order to do proper cleanup when the refcnt reaches 0. Otherwise, the refcnt can reach zero without the inet6_dev being destroyed and we end up leaking a reference to the net_device and see messages like the following, unregister_netdevice: waiting for eth0 to become free. Usage count = 1 Tested on linux-3.4.43. Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | ipv4 igmp: use in_dev_put in timer handlers instead of __in_dev_putSalam Noureddine2013-09-301-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is possible for the timer handlers to run after the call to ip_mc_down so use in_dev_put instead of __in_dev_put in the handler function in order to do proper cleanup when the refcnt reaches 0. Otherwise, the refcnt can reach zero without the in_device being destroyed and we end up leaking a reference to the net_device and see messages like the following, unregister_netdevice: waiting for eth0 to become free. Usage count = 1 Tested on linux-3.4.43. Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | ethernet: moxa: fix incorrect placement of __initdata tagBartlomiej Zolnierkiewicz2013-09-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | __initdata tag should be placed between the variable name and equal sign for the variable to be placed in the intended .init.data section. In this particular case __initdata is incorrect as moxart_mac_driver can be used after the driver gets initialized. Also while at it static-ize moxart_mac_driver. Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | ipv6: gre: correct calculation of max_headroomHannes Frederic Sowa2013-09-301-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | gre_hlen already accounts for sizeof(struct ipv6_hdr) + gre header, so initialize max_headroom to zero. Otherwise the if (encap_limit >= 0) { max_headroom += 8; mtu -= 8; } increments an uninitialized variable before max_headroom was reset. Found with coverity: 728539 Cc: Dmitry Kozlov <xeb@mail.ru> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | powerpc/83xx: gianfar_ptp: select 1588 clock source through dts fileAida Mynzhasova2013-09-302-2/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently IEEE 1588 timer reference clock source is determined through hard-coded value in gianfar_ptp driver. This patch allows to select ptp clock source by means of device tree file node. For instance: fsl,cksel = <0>; for using external (TSEC_TMR_CLK input) high precision timer reference clock. Other acceptable values: <1> : eTSEC system clock <2> : eTSEC1 transmit clock <3> : RTC clock input When this attribute isn't used, eTSEC system clock will serve as IEEE 1588 timer reference clock. Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru> Acked-by: Kumar Gala <galak@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | Revert "powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file"David S. Miller2013-09-302-18/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 894116bd0e9b7749a0c4b6c62dec13c2a0ccef68. I applied the wrong version of this patch, correct version coming up. Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | bonding: Fix broken promiscuity reference counting issueNeil Horman2013-09-301-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recently grabbed this report: https://bugzilla.redhat.com/show_bug.cgi?id=1005567 Of an issue in which the bonding driver, with an attached vlan encountered the following errors when bond0 was taken down and back up: dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of device might be broken. The error occurs because, during __bond_release_one, if we release our last slave, we take on a random mac address and issue a NETDEV_CHANGEADDR notification. With an attached vlan, the vlan may see that the vlan and bond mac address were in sync, but no longer are. This triggers a call to dev_uc_add and dev_set_rx_mode, which enables IFF_PROMISC on the bond device. Then, when we complete __bond_release_one, we use the current state of the bond flags to determine if we should decrement the promiscuity of the releasing slave. But since the bond changed promiscuity state during the release operation, we incorrectly decrement the slave promisc count when it wasn't in promiscuous mode to begin with, causing the above error Fix is pretty simple, just cache the bonding flags at the start of the function and use those when determining the need to set promiscuity. This is also needed for the ALLMULTI flag CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Mark Wu <wudxw@linux.vnet.ibm.com> CC: "David S. Miller" <davem@davemloft.net> Reported-by: Mark Wu <wudxw@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | tcp: TSQ can use a dynamic limitEric Dumazet2013-09-301-6/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When TCP Small Queues was added, we used a sysctl to limit amount of packets queues on Qdisc/device queues for a given TCP flow. Problem is this limit is either too big for low rates, or too small for high rates. Now TCP stack has rate estimation in sk->sk_pacing_rate, and TSO auto sizing, it can better control number of packets in Qdisc/device queues. New limit is two packets or at least 1 to 2 ms worth of packets. Low rates flows benefit from this patch by having even smaller number of packets in queues, allowing for faster recovery, better RTT estimations. High rates flows benefit from this patch by allowing more than 2 packets in flight as we had reports this was a limiting factor to reach line rate. [ In particular if TX completion is delayed because of coalescing parameters ] Example for a single flow on 10Gbp link controlled by FQ/pacing 14 packets in flight instead of 2 $ tc -s -d qd qdisc fq 8001: dev eth0 root refcnt 32 limit 10000p flow_limit 100p buckets 1024 quantum 3028 initial_quantum 15140 Sent 1168459366606 bytes 771822841 pkt (dropped 0, overlimits 0 requeues 6822476) rate 9346Mbit 771713pps backlog 953820b 14p requeues 6822476 2047 flow, 2046 inactive, 1 throttled, delay 15673 ns 2372 gc, 0 highprio, 0 retrans, 9739249 throttled, 0 flows_plimit Note that sk_pacing_rate is currently set to twice the actual rate, but this might be refined in the future when a flow is in congestion avoidance. Additional change : skb->destructor should be set to tcp_wfree(). A future patch (for linux 3.13+) might remove tcp_limit_output_bytes Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | dm9601: fix IFF_ALLMULTI handlingPeter Korsgaard2013-09-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pass-all-multicast is controlled by bit 3 in RX control, not bit 2 (pass undersized frames). Reported-by: Joseph Chang <joseph_chang@davicom.com.tw> Signed-off-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | pkt_sched: fq: qdisc dismantle fixesEric Dumazet2013-09-301-20/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | fq_reset() should drops all packets in queue, including throttled flows. This patch moves code from fq_destroy() to fq_reset() to do the cleaning. fq_change() must stop calling fq_dequeue() if all remaining packets are from throttled flows. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | net: flow_dissector: fix thoff for IPPROTO_AHEric Dumazet2013-09-301-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit 8ed781668dd49 ("flow_keys: include thoff into flow_keys for later usage"), we missed that existing code was using nhoff as a temporary variable that could not always contain transport header offset. This is not a problem for TCP/UDP because port offset (@poff) is 0 for these protocols. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | MAINTAINERS: add myself as maintainer of xen-netbackWei Liu2013-09-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Wei Liu <wei.liu2@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | xen-netback: Handle backend state transitions in a more robust wayPaul Durrant2013-09-301-30/+118
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the frontend state changes netback now specifies its desired state to a new function, set_backend_state(), which transitions through any necessary intermediate states. This fixes an issue observed with some old Windows frontend drivers where they failed to transition through the Closing state and netback would not behave correctly. Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: David Vrabel <david.vrabel@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | ipv6: Fix preferred_lft not updating in some casesPaul Marks2013-09-301-37/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consider the scenario where an IPv6 router is advertising a fixed preferred_lft of 1800 seconds, while the valid_lft begins at 3600 seconds and counts down in realtime. A client should reset its preferred_lft to 1800 every time the RA is received, but a bug is causing Linux to ignore the update. The core problem is here: if (prefered_lft != ifp->prefered_lft) { Note that ifp->prefered_lft is an offset, so it doesn't decrease over time. Thus, the comparison is always (1800 != 1800), which fails to trigger an update. The most direct solution would be to compute a "stored_prefered_lft", and use that value in the comparison. But I think that trying to filter out unnecessary updates here is a premature optimization. In order for the filter to apply, both of these would need to hold: - The advertised valid_lft and preferred_lft are both declining in real time. - No clock skew exists between the router & client. So in this patch, I've set "update_lft = 1" unconditionally, which allows the surrounding code to be greatly simplified. Signed-off-by: Paul Marks <pmarks@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | ip_tunnel: Do not use stale inner_iph pointer.Pravin B Shelar2013-09-301-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While sending packet skb_cow_head() can change skb header which invalidates inner_iph pointer to skb header. Following patch avoid using it. Found by code inspection. This bug was introduced by commit 0e6fbc5b6c6218 (ip_tunnels: extend iptunnel_xmit()). Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | net: qmi_wwan: fix Cinterion PLXX product IDAleksander Morgado2013-09-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1. The blacklisting in the serial/option driver does actually use the correct PID, as per commit 8ff10bdb14a52e3f25d4ce09e0582a8684c1a6db ('USB: Blacklisted Cinterion's PLxx WWAN Interface'). CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> CC: Christian Schmiedl <christian.schmiedl@gemalto.com> CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com> Signed-off-by: Aleksander Morgado <aleksander@lanedo.com> Acked-by: Bjørn Mork <bjorn@mork.no> Acked-by: Christian Schmiedl <christian.schmiedl@gemalto.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | powerpc/83xx: gianfar_ptp: select 1588 clock source through dts fileAida Mynzhasova2013-09-302-2/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently IEEE 1588 timer reference clock source is determined through hard-coded value in gianfar_ptp driver. This patch allows to select ptp clock source by means of device tree file node. For instance: fsl,cksel = <0>; for using external (TSEC_TMR_CLK input) high precision timer reference clock. Other acceptable values: <1> : eTSEC system clock <2> : eTSEC1 transmit clock <3> : RTC clock input When this attribute isn't used, eTSEC system clock will serve as IEEE 1588 timer reference clock. Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | vxlan: Use RCU apis to access sk_user_data.Pravin B Shelar2013-09-302-6/+8
| | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use of RCU api makes vxlan code easier to understand. It also fixes bug due to missing ACCESS_ONCE() on sk_user_data dereference. In rare case without ACCESS_ONCE() compiler might omit vs on sk_user_data dereference. Compiler can use vs as alias for sk->sk_user_data, resulting in multiple sk_user_data dereference in rcu read context which could change. CC: Jesse Gross <jesse@nicira.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | net: net_secret should not depend on TCPEric Dumazet2013-09-283-7/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A host might need net_secret[] and never open a single socket. Problem added in commit aebda156a570782 ("net: defer net_secret[] initialization") Based on prior patch from Hannes Frederic Sowa. Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@strressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-31 18:00:32 +0000