| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| | |
bigger tree-wide changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- Another set of OMAP fixes
* Clock fixes
* Restart handling
* PHY regulators
* SATA hwmod data for DRA7
+ Some trivial fixes and removal of a bit of dead code
- Exynos fixes
* A bunch of clock fixes
* Some SMP fixes
* Exynos multi-core timer: register as clocksource and fix ftrace.
+ a few other minor fixes
There's also a couple more patches, and at91 fix for USB caused by
common clock conversion, and more MAINTAINERS entries for shmobile.
We're definitely switching to only regression fixes from here on out,
we've been a little less strict than usual up until now"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: at91: at91sam9x5: add clocks for usb device
ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
ARM: dts: Add clock property for mfc_pd in exynos5420
clk: exynos5420: Add IDs for clocks used in PD mfc
ARM: EXYNOS: Add support for clock handling in power domain
ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
ARM: imx: fix shared gate clock
ARM: dts: Update the parent for Audss clocks in Exynos5420
ARM: EXYNOS: Update secondary boot addr for secure mode
ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
ARM: dts: am335x-evm: Enable the McASP FIFO for audio
ARM: OMAP2+: Make GPMC skip disabled devices
ARM: OMAP2+: create dsp device only on OMAP3 SoCs
ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
ARM: DRA7: hwmod: Fixup SATA hwmod
ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
While powering on/off a local powerdomain in exynos5 chipsets, the
input clocks to each device gets modified. This behaviour is based
on the SYSCLK_SYS_PWR_REG registers.
E.g. SYSCLK_MFC_SYS_PWR_REG = 0x0, the parent of input clock to MFC
(aclk333) gets modified to oscclk
= 0x1, no change in clocks.
The recommended value of SYSCLK_SYS_PWR_REG before power gating any
domain is 0x0. So we must also restore the clocks while powering on
a domain everytime.
This patch adds the framework for getting the required mux and parent
clocks through a power domain device node. With this patch, while
powering off a domain, parent is set to oscclk and while powering back
on, its re-set to the correct parent which is as per the recommended
pd on/off sequence.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small serial fixes that resolve some reported problems
that started in 3.15 with some serial drivers.
And there's a new dt binding for a serial driver, which was all that
was needed for the renesas serial driver"
* tag 'tty-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0
serial: imx: Fix build breakage
serial: arc_uart: Use uart_circ_empty() for open-coded comparison
serial: Test for no tx data on tx restart
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Simply document new compat strings.
There appears to be no need for a driver updates.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Dell kernel driver dell-smo8800 provides same freefall interface as hp_accel so
program hpfall.c works also on Dell laptops. So rename it to freefall.c.
Dell driver does not provide hp::hddprotect led so make sure that freefall.c
works also if hp::hddprotect does not exist in sysfs.
Additionally write info to syslog.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Sonal Santan <sonal.santan@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch fixed spelling typo in various template files
within Documentation/Docbook.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch fixed spelling typo found in DocBook/mtdnand.tmpl.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The paragraph on mcelog currently describes kernel v2.6.31. In that
kernel the mce code (for i386, that is) was in transition. Ever since
v2.6.32 the situation is much simpler (eg, mcelog is now needed to
process events on almost all x86 machines, i386 and x86-64). Since this
"document is designed to provide a list of the minimum levels of
software necessary to run the 3.0 kernels" let's just describe that
situation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | |\ \
| | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | | |
* pm-cpufreq:
cpufreq: Makefile: fix compilation for davinci platform
intel_pstate: Set CPU number before accessing MSRs
intel_pstate: Update documentation of {max,min}_perf_pct sysfs files
intel_pstate: don't touch turbo bit if turbo disabled or unavailable.
intel_pstate: Fix setting VID
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Update documentation to make the interpretation of the values clearer
Link: https://bugzilla.kernel.org/show_bug.cgi?id=64251
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
vmscan/mm_vmscan_lru_isolate
When using trace-vmscan-postprocess.pl for checking the file/anon rate
of scanning, we can find that it can not be performed. At the same
time, the following message will be reported:
WARNING: Format not as expected for event vmscan/mm_vmscan_lru_isolate
'file' != 'contig_taken' Fewer fields than expected in format at
./trace-vmscan-postprocess.pl line 171, <FORMAT> line 76.
In trace-vmscan-postprocess.pl, (contig_taken, contig_dirty, and
contig_failed) are be associated respectively to (nr_lumpy_taken,
nr_lumpy_dirty, and nr_lumpy_failed) for lumpy reclaim. Via commit
c53919adc045 ("mm: vmscan: remove lumpy reclaim"), lumpy reclaim had
already been removed by Mel, but the update for
trace-vmscan-postprocess.pl was missed.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Pull ARM fixes from Russell King:
"Another round of ARM fixes. The largest change here is the L2 changes
to work around problems for the Armada 37x/380 devices, where most of
the size comes down to comments rather than code.
The other significant fix here is for the ptrace code, to ensure that
rewritten syscalls work as intended. This was pointed out by Kees
Cook, but Will Deacon reworked the patch to be more elegant.
The remainder are fairly trivial changes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
ARM: 8086/1: Set memblock limit for nommu
ARM: 8085/1: sa1100: collie: add top boot mtd partition
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
ARM: 8080/1: mcpm.h: remove unused variable declaration
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
These days most people use git to send patches so I have added a section
about that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the biggest one being a fix for the newly
added Qualcomm SPI controller driver to make it not use its internal
chip select due to hardware bugs, replacing it with GPIOs"
* tag 'spi-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Remove chip select function
spi: qup: Fix order of spi_register_master
spi: sh-sci: fix use-after-free in sh_sci_spi_remove()
spi/pxa2xx: fix incorrect SW mode chipselect setting for BayTrail LPSS SPI
|
| | | | \ | |
| | | | \ | |
| | | | \ | |
| | | | \ | |
| | | |\ \ \|
| | | | | |
| | | | | |
| | | | | | |
'spi/fix/sh-sci' into spi-linus
|
| | | | | |/
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch removes the chip select function. Chip select should instead be
supported using GPIOs, defining the DT entry "cs-gpios", and letting the SPI
core assert/deassert the chip select as it sees fit.
The chip select control inside the controller is buggy. It is supposed to
automatically assert the chip select based on the activity in the controller,
but it is buggy and doesn't work at all. So instead we elect to use GPIOs.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here includes a few patchset for fixing mostly HD-audio issues in
addition to a patch assuring the compress API bytes alignment and a
fix for the die-hard existing race condition at USB-audio
disconnection. The volume looks big in Realtek HD-audio code, but
it's just a translation of the fixup tables, and the actual changes
are rather trivial"
* tag 'sound-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N values when resuming HSW/BDW display controller
ALSA: usb-audio: Fix races at disconnection and PCM closing
ALSA: hda - Adjust speaker HPF and add LED support for HP Spectre 13
ALSA: hda - Make the pin quirk tables use the SND_HDA_PIN_QUIRK macro
ALSA: hda - Make a SND_HDA_PIN_QUIRK macro
ALSA: hda - Add pin quirk for Dell XPS 15
ALSA: hda - hdmi: call overridden init on resume
ALSA: hda - Fix usage of "model" module parameter
ALSA: compress: fix the struct alignment to 4 bytes
|
| | | | |_|/
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
HP Spectre 13 has the IDT 92HD95 codec, and BIOS seems to set the
default high-pass filter in some "safer" range, which results in the
very soft tone from the built-in speakers in contrast to Windows.
Also, the mute LED control is missing, since 92HD95 codec still has no
HP-specific fixups for GPIO setups.
This patch adds these missing features: the HPF is adjusted by the
vendor-specific verb, and the LED is set up from a DMI string (but
with the default polarity = 0 assumption due to the incomplete BIOS on
the given machine).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=74841
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Various minor fixes"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpio-fan) Change name used in hwmon_device_register_with_groups
hwmon: (emc1403) Fix missing 'select REGMAP_I2C' in Kconfig
hwmon: (ntc_thermistor) Use the manufacturer name properly
devicetree: bindings: Document murata vendor prefix
hwmon: (w83l786ng) Report correct minimum fan speed
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Murata Manufacturing Co., Ltd is the vendor for
NTC (Negative Temperature coefficient) based Thermistors.
But, the driver extensively uses "NTC" as the vendor name.
This patch corrects the vendor name also updates the
compatibility strings according to the vendor-prefix.txt
Note: Drivers continue to support the previous compatible strings
but further addition of these compatible strings in device tree
is deprecated.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
| | | | |/ /
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Add Murata Manufacturing Co., Ltd. to the list of device tree
vendor prefixes.
Murata manufactures NTC (Negative Temperature Coefficient) based
Thermistors for small scale applications like Mobiles and PDAs.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Pull networking fixes from David Miller:
1) Fix crash in ipvs tot_stats estimator, from Julian Anastasov.
2) Fix OOPS in nf_nat on netns removal, from Florian Westphal.
3) Really really really fix locking issues in slip and slcan tty write
wakeups, from Tyler Hall.
4) Fix checksum offloading in fec driver, from Fugang Duan.
5) Off by one in BPF instruction limit test, from Kees Cook.
6) Need to clear all TSO capability flags when doing software TSO in
tg3 driver, from Prashant Sreedharan.
7) Fix memory leak in vlan_reorder_header() error path, from Li
RongQing.
8) Fix various bugs in xen-netfront and xen-netback multiqueue support,
from David Vrabel and Wei Liu.
9) Fix deadlock in cxgb4 driver, from Li RongQing.
10) Prevent double free of no-cache DST entries, from Eric Dumazet.
11) Bad csum_start handling in skb_segment() leads to crashes when
forwarding, from Tom Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: fix setting csum_start in skb_segment()
ipv4: fix dst race in sk_dst_get()
net: filter: Use kcalloc/kmalloc_array to allocate arrays
trivial: net: filter: Change kerneldoc parameter order
trivial: net: filter: Fix typo in comment
net: allwinner: emac: Add missing free_irq
cxgb4: use dev_port to identify ports
xen-netback: bookkeep number of active queues in our own module
tg3: Change nvram command timeout value to 50ms
cxgb4: Not need to hold the adap_rcu_lock lock when read adap_rcu_list
be2net: fix qnq mode detection on VFs
of: mdio: fixup of_phy_register_fixed_link parsing of new bindings
at86rf230: fix irq setup
net: phy: at803x: fix coccinelle warnings
net/mlx4_core: Fix the error flow when probing with invalid VF configuration
tulip: Poll link status more frequently for Comet chips
net: huawei_cdc_ncm: increase command buffer size
drivers: net: cpsw: fix dual EMAC stall when connected to same switch
xen-netfront: recreate queues correctly when reconnecting
xen-netfront: fix oops when disconnected from backend
...
|
| | | | |/ /
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
clock_adjtime was included in glibc 2.14. _GNU_SOURCE must be defined
to make it available.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A new set of bug fixes for 3.16, containing patches for seven
platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
ARM: integrator: fix OF-related regression
ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
ARM: dts: kirkwood: fix phy-connection-type for Guruplug
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
ARM: dts: imx51-babbage: Fix esdhc setup
ARM: dts: mx5: Move the display out of soc {} node
ARM: dts: mx5: Fix IPU port node placement
ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
ARM: mvebu: Fix broken SoC ID detection
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
ARM: multi_v7_defconfig: Add QCOM GSBI driver
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
tty: serial: msm: Fix section mismatch warning
...
|
| | | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
wildcard
Wildcards in compatible strings should be avoid. "marvell,armada38x"
was recently introduced but was not yet used.
The armada 385 SoC is a superset of the armada 380 SoC (with more CPUs
and more PCIe slots). So this patch replaces the use of
"marvell,armada38x" by the "marvell,armada380" string.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1403533011-21339-1-git-send-email-gregory.clement@free-electrons.com
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
A 'softlockup' is defined as a bug that causes the kernel to loop in
kernel mode for more than a predefined period to time, without giving
other tasks a chance to run.
Currently, upon detection of this condition by the per-cpu watchdog
task, debug information (including a stack trace) is sent to the system
log.
On some occasions, we have observed that the "victim" rather than the
actual "culprit" (i.e. the owner/holder of the contended resource) is
reported to the user. Often this information has proven to be
insufficient to assist debugging efforts.
To avoid loss of useful debug information, for architectures which
support NMI, this patch makes it possible to improve soft lockup
reporting. This is accomplished by issuing an NMI to each cpu to obtain
a stack trace.
If NMI is not supported we just revert back to the old method. A sysctl
and boot-time parameter is available to toggle this feature.
[dzickus@redhat.com: add CONFIG_SMP in certain areas]
[akpm@linux-foundation.org: additional CONFIG_SMP=n optimisations]
[mq@suse.cz: fix warning]
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mateusz Guzik <mguzik@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
strncpy call
Added a guaranteed null-terminate after call to strncpy.
This was partly found using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Oleg reports a division by zero error on zero-length write() to the
percpu_pagelist_fraction sysctl:
divide error: 0000 [#1] SMP DEBUG_PAGEALLOC
CPU: 1 PID: 9142 Comm: badarea_io Not tainted 3.15.0-rc2-vm-nfs+ #19
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task: ffff8800d5aeb6e0 ti: ffff8800d87a2000 task.ti: ffff8800d87a2000
RIP: 0010: percpu_pagelist_fraction_sysctl_handler+0x84/0x120
RSP: 0018:ffff8800d87a3e78 EFLAGS: 00010246
RAX: 0000000000000f89 RBX: ffff88011f7fd000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000010
RBP: ffff8800d87a3e98 R08: ffffffff81d002c8 R09: ffff8800d87a3f50
R10: 000000000000000b R11: 0000000000000246 R12: 0000000000000060
R13: ffffffff81c3c3e0 R14: ffffffff81cfddf8 R15: ffff8801193b0800
FS: 00007f614f1e9740(0000) GS:ffff88011f440000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f614f1fa000 CR3: 00000000d9291000 CR4: 00000000000006e0
Call Trace:
proc_sys_call_handler+0xb3/0xc0
proc_sys_write+0x14/0x20
vfs_write+0xba/0x1e0
SyS_write+0x46/0xb0
tracesys+0xe1/0xe6
However, if the percpu_pagelist_fraction sysctl is set by the user, it
is also impossible to restore it to the kernel default since the user
cannot write 0 to the sysctl.
This patch allows the user to write 0 to restore the default behavior.
It still requires a fraction equal to or larger than 8, however, as
stated by the documentation for sanity. If a value in the range [1, 7]
is written, the sysctl will return EINVAL.
This successfully solves the divide by zero issue at the same time.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Oleg Drokin <green@linuxhacker.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | | |/ /
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Documentation/memory-hotplug.txt incorrectly states that the memory
driver "probe" interface is only supported on powerpc and is vague about
its application on x86. Clarify the platforms that make this interface
available if memory hotplug is enabled.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c new drivers from Wolfram Sang:
"Here is a pull request from i2c hoping for the "new driver" rule.
Originally, I wanted to send this request during the merge window, but
code checkers with very recent additions complained, so a few fixups
were needed. So, some more time went by and I merged rc1 to get a
stable base"
So the "new driver" rule is really about drivers that people absolutely
need for the kernel to work on new hardware, which is not so much the
case for i2c. So I considered not pulling this, but eventually
relented.
Just for FYI: the whole (and only) point of "new drivers" is not that
new drivers cannot regress things (they can, and they have - by
triggering badly tested code on machines that never triggered that code
before), but because they can bring to life machines that otherwise
wouldn't be useful at all without the drivers.
So the new driver rule is for essential things that actual consumers
would care about, ie devices like networking or disk drivers that matter
to normal people (not server people - they run old kernels anyway, so
mainlining new drivers is irrelevant for them).
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sun6-p2wi: fix call to snprintf
i2c: rk3x: add NULL entry to the end of_device_id array
i2c: sun6i-p2wi: use proper return value in probe
i2c: sunxi: add P2WI (Push/Pull 2 Wire Interface) controller support
i2c: sunxi: add P2WI DT bindings documentation
i2c: rk3x: add driver for Rockchip RK3xxx SoC I2C adapter
|
| | | |\| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Merge a stable base (Linux 3.16-rc1)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
P2WI (Push/Pull 2 Wire Interface) is an SMBus like bus used to communicate
with some PMICs (like the AXP221).
Document P2WI DT bindings which are pretty much the same as the one defined
for the marvell's mv64xxx controller.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Driver for the native I2C adapter found in Rockchip RK3xxx SoCs.
Configuration is only possible through devicetree. The driver is
interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"There are three fixes for regressions caused by the relative paths
series: deb-pkg, tar-pkg and *docs did not work with O=.
Plus, there is a fix for the linux-headers deb package and a fixed
typo. These are not regression fixes but are safe enough"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: fix a typo in a kbuild document
builddeb: fix missing headers in linux-headers package
Documentation: Fix DocBook build with relative $(srctree)
kbuild: Fix tar-pkg with relative $(objtree)
deb-pkg: Fix for relative paths
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
| | | | |/ /
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
After commits 890676c6 (kbuild: Use relative path when building in the source
tree) and 9da0763b (kbuild: Use relative path when building in a subdir
of the source tree), the $(srctree) variable can be a relative path.
This breaks Documentation/DocBook/media/Makefile, because it tries to
create symlinks from a subdirectory of the object tree to the source
tree. Fix this by using a full path in this case.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes mostly (ia64 regression related to the ACPI
enumeration of devices, cpufreq regressions, fix for I2C controllers
included in Intel SoCs, mvebu cpuidle driver fix related to sysfs)
plus additional kernel command line arguments from Kees to make it
possible to build kernel images with hibernation and the kernel
address space randomization included simultaneously, a new ACPI
battery driver quirk for a system with a broken BIOS and a couple of
ACPI core cleanups.
Specifics:
- Fix for an ia64 regression introduced during the 3.11 cycle by a
commit that modified the hardware initialization ordering and made
device discovery fail on some systems.
- Fix for a build problem on systems where the cpufreq-cpu0 driver is
built-in and the cpu-thermal driver is modular from Arnd Bergmann.
- Fix for a recently introduced computational mistake in the
intel_pstate driver that leads to excessive rounding errors from
Doug Smythies.
- Fix for a failure code path in cpufreq_update_policy() that fails
to unlock the locks acquired previously from Aaron Plattner.
- Fix for the cpuidle mvebu driver to use shorter state names which
will prevent the sysfs interface from returning mangled strings.
From Gregory Clement.
- ACPI LPSS driver fix to make sure that the I2C controllers included
in BayTrail SoCs are not held in the reset state while they are
being probed from Mika Westerberg.
- New kernel command line arguments making it possible to build
kernel images with hibernation and kASLR included at the same time
and to select which of them will be used via the command line (they
are still functionally mutually exclusive, though). From Kees
Cook.
- ACPI battery driver quirk for Acer Aspire V5-573G that fails to
send battery status change notifications timely from Alexander
Mezin.
- Two ACPI core cleanups from Christoph Jaeger and Fabian Frederick"
* tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: mvebu: Fix the name of the states
cpufreq: unlock when failing cpufreq_update_policy()
intel_pstate: Correct rounding in busy calculation
ACPI: use kstrto*() instead of simple_strto*()
ACPI / processor replace __attribute__((packed)) by __packed
ACPI / battery: add quirk for Acer Aspire V5-573G
ACPI / battery: use callback for setting up quirks
ACPI / LPSS: Take I2C host controllers out of reset
x86, kaslr: boot-time selectable with hibernation
PM / hibernate: introduce "nohibernate" boot parameter
cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
ACPI / ia64 / sba_iommu: Restore the working initialization ordering
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Changes kASLR from being compile-time selectable (blocked by
CONFIG_HIBERNATION), to being boot-time selectable (with hibernation
available by default) via the "kaslr" kernel command line.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
To support using kernel features that are not compatible with hibernation,
this creates the "nohibernate" kernel boot parameter to disable both
hibernation and resume. This allows hibernation support to be a boot-time
choice instead of only a compile-time choice.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | |\ \ \ \
| | |/ / /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next
This is bigger because it regenerates the internal firmwares after a fix.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/doc: update the thermal documentation
drm/nouveau/pwr: fix typo in fifo wrap handling
drm/nv50/disp: fix a potential oops in supervisor handling
drm/nouveau/disp/dp: don't touch link config after success
drm/nouveau/kms: reference vblank for crtc during pageflip.
drm/gk104/fb/ram: fixups from an earlier search+replace
drm/nv50/gr: remove an unneeded write while initialising PGRAPH
drm/nv50/gr: fix overlap while zeroing zcull regions
drm/gf100-/gr: report class data to host on fwmthd failure
drm/gk104/ibus: increase various random timeouts
drm/gk104/clk: only touch divider for mode we'll be using
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Changes:
- Change the maintainer's address (the labri address will expire soon);
- Drop the note about not all families supporting all fan modes;
- Add a note about the reported RPM not being accurate when driven outside
the vbios-defined PWM range.
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
| |/ / / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We always use resched_task() with rq->curr argument.
It's not possible to reschedule any task but rq's current.
The patch introduces resched_curr(struct rq *) to
replace all of the repeating patterns. The main aim
is cleanup, but there is a little size profit too:
(before)
$ size kernel/sched/built-in.o
text data bss dec hex filename
155274 16445 7042 178761 2ba49 kernel/sched/built-in.o
$ size vmlinux
text data bss dec hex filename
7411490 1178376 991232 9581098 92322a vmlinux
(after)
$ size kernel/sched/built-in.o
text data bss dec hex filename
155130 16445 7042 178617 2b9b9 kernel/sched/built-in.o
$ size vmlinux
text data bss dec hex filename
7411362 1178376 991232 9580970 9231aa vmlinux
I was choosing between resched_curr() and resched_rq(),
and the first name looks better for me.
A little lie in Documentation/trace/ftrace.txt. I have not
actually collected the tracing again. With a hope the patch
won't make execution times much worse :)
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20140628200219.1778.18735.stgit@localhost
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Document new compatible strings for clock provided by the PRCM
(Power/Reset/Clock Management) unit.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Support for the USB gates and resets on A31 has been recently added
using a new compatible, so let's document it here.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | | |
clk-next
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
frequencies
MPU DPLL on OMAP5, DRA75x, DRA72x has a limitation on the maximum
frequency it can be locked at. Duty Cycle Correction circuit is used
to recover a correct duty cycle for achieving higher frequencies
(hardware internally switches output to M3 output(CLKOUTHIF) from M2
output (CLKOUT)).
So provide support to setup required data to handle Duty cycle by
the setting up the minimum frequency for DPLL. 1.4GHz is common
for all these devices and is based on Technical Reference Manual
information for OMAP5432((SWPU282U) chapter 3.6.3.3.1 "DPLLs Output
Clocks Parameters", and equivalent information from DRA75x, DRA72x
documentation(SPRUHP2E, SPRUHI2P).
Signed-off-by: Nishanth Menon <nm@ti.com>
[t-kristo@ti.com: updated for latest dpll init API call]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Audio Tracking Logic is designed to be used by HD Radio applications to
synchronize the audio output clocks to the baseband clock. ATL can be also
used to track errors between two reference clocks (BWS, AWS) and generate a modulated
clock output which averages to some desired frequency.
In essence ATL is generating a clock to be used by an audio codec and also
to be used by the SoC as MCLK.
To be able to integrate the ATL provided clocks to the clock tree we need
two types of DT binding:
- DT clock nodes to represent the ATL clocks towards the CCF
- binding for the ATL IP itself which is going to handle the hw
configuration
The reason for this type of setup is that ATL itself is a separate device
in the SoC, it has it's own address space and clock domain. Other IPs can
use the ATL generated clock as their functional clock (McASPs for example)
and external components like audio codecs can also use the very same clock
as their MCLK.
The ATL IP in DRA7 contains 4 ATL instences.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
