| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In the new behavior, the sja1105 driver expects there to be explicit
RGMII delays present on the fixed-link ports, otherwise it will complain
that it falls back to legacy behavior, which is to apply RGMII delays
incorrectly derived from the phy-mode string.
In this case, the legacy behavior of the driver is to not apply delays
in any direction (mostly because the SJA1105T can't do that, so this
board uses PCB traces). To preserve that but also silence the driver,
use explicit delays of 0 ns. The delay information from the phy-mode is
ignored by new kernels (it's still RGMII as long as it's "rgmii*"
something), and the explicit {rx,tx}-internal-delay-ps properties are
ignored by old kernels, so the change works both ways.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
We cannot list all the possible chips used in different board revisions,
just use the generic "jedec,spi-nor" compatible instead. This also
fixes dtbs_check error:
['jedec,spi-nor', 's25fl256s1', 's25fl512s'] is too long
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
| |
Property "postion" is not documented in the mma8452 binding. Remove it
to resolve the error in "make dtbs_check"
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
| |
Align the compatible strings with the board binding defined in schema
file.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and eth1
have interrupt lines connected to the shared IRQ2_B LS1021A pin.
Switching to interrupts offloads the PHY library from the task of
polling the MDIO status and AN registers (1, 4, 5) every second.
Unfortunately, the BCM5464R quad PHY connected to the switch does not
appear to have an interrupt line routed to the SoC.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
It has two regular Ethernet ports and four switched, TSN-capable ports.
It also features:
- One Arduino header
- One expansion header
- Two USB 3.0 ports
- One mini PCIe slot
- One SATA interface
- Accelerometer, gyroscope, temperature sensors
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
