| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add clock control support for sh7372 CMT hardware blocks.
No upstream sh7372 boards are making use of CMT3 + CMT4,
but the sh7372 hardware happens to come out of reset with
all CMT MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.
This patch relies on the recently merged
794d78f drivers: sh: late disabling of clocks V2
to make sure the unused clocks get disabled as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add clock control support for sh7372 MSIOF hardware blocks.
No upstream sh7372 boards are making use of MSIOF0->2,
but the sh7372 hardware happens to come out of reset with
all MSIOF MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.
This patch relies on the recently merged
794d78f drivers: sh: late disabling of clocks V2
to make sure the unused clocks get disabled as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
USB-DMAC1 needs SMSTPCR4/MSTP407 controls, not MSTP214
this patch tested on mackerel board
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
MAINCKSEL is [29:28], not [27:24]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch removes support for the SGX interrupt source in
the sh7372 INTCS controller.
The SGX hardware block included in sh7372 is already hooked
up to the ARM Cortex-A8 core using the INTCA controller,
so SGX users are encouraged to make use of that interrupt
source instead.
Removing support for the SGX interrupt source in INTCS
simplifies the sh7372 power management code by allowing
us to assume that only INTCA needs to be powered on to
operate the SGX hardware.
If the INTCS interrupt source would be kept then the kernel
would be forced to deal with additional dependencies that does
not follow the regular power domain hiearachy. With this
patch in place we can safely power down INTCS while the
SGX is operating.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | |\ \ \ |
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This patch use channel0 as Tx, and channel1 as Rx
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | |\ \ \ \
| | | |_|/
| | |/| |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into rmobile-latest
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This corrects a logic-error that I made in the original implementation.
An alternate patch would be to just remove these lines and
leave the clock running as it is reconfigured later on during
boot anyway.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | |\ \ \ \ |
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The SDHI block on the ag5evm requires waiting for idle
before writing to some registers.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Make sure that the 'static' keywork is at the beginning of declaration
for arch/arm/mach-shmobile/board-ap4evb.c
This gets rid of warnings like
warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Switch the sh7372 CPU support to use CMT2 instead
of CMT1 for system timer.
CMT1 is located in the A3SP power domain while CMT2
is located in the always-on power domain C5.
This improves our PM situation - with CMT2 as timer
we can power down A3SP and still access the timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |\ \ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: mach-shmobile: sh7372 LCDC1 suspend fix V2 (incremental)
OMAP: omap_device: only override _noirq methods, not normal suspend/resume
PM / Runtime: Correct documentation of pm_runtime_irq_safe()
ARM: mach-shmobile: sh7372 LCDC1 suspend fix
sh-sci / PM: Use power.irq_safe
PM: Use spinlock instead of mutex in clock management functions
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
- Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Commit c03f007a8bf0e092caeb6856a5c8a850df10b974 (OMAP: PM:
omap_device: add system PM methods for PM domain handling) mistakenly
used SET_SYSTEM_SLEEP_PM_OPS() when trying to configure custom methods
for the PM domains noirq methods. Fix that by setting only the
suspend_noirq and resume_noirq methods with custom versions.
Note that all other PM domain methods (including the "normal"
suspend/resume methods) are populated using USE_PLATFORM_PM_SLEEP_OPS,
which configures them all to the default subsystem (platform_bus)
methods.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| | | |_|_|_|/
| |/| | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Associate the HDMI clock together with LCDC1 on sh7372.
Without this patch Suspend-to-RAM hangs on the boards
AP4EVB and Mackerel. The code hangs in the LCDC driver
where the software is waiting forever for the hardware to
power down. By explicitly associating the HDMI clock with
LCDC1 we can make sure the HDMI clock is enabled using
Runtime PM whenever the driver is accessing the hardware.
This HDMI and LCDC1 dependency is documented in the sh7372
data sheet. Older kernels did work as expected but the
recently merged (3.1-rc)
794d78f drivers: sh: late disabling of clocks V2
introduced code to turn off clocks lacking software reference
which happens to include the HDMI clock that is needed by
LCDC1 to operate as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
| |/ / / / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
ARM: mmp: Change the way we use timer 0 as clockevent timer.
ARM: mmp: Switch to using timer 1 as clocksource timer.
ARM: mmp: Also start timer 1 on boot.
ARM: pxa168/gplugd: free correct GPIO
ARM: pxa168/gplugd: get rid of mfp-gplugd.h
ARM: pxa: fix logic error in PJ4 iWMMXt handling
mach-sa1100: fix PCI build problem
omap: timer: Set dmtimer used as clocksource in autoreload mode
OMAP3: am3517crane: remove NULL board_mux from board file
arm: mach-omap2: mux: use kstrdup()
arch:arm:plat-omap:iovmm: remove unused variable 'va'
Update Nook Color machine 3284 to common Encore name
am3505/3517: Various platform defines for UART4
OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
iMX: Fix build for iMX53
ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
OMAP3: beagle: don't touch omap_device internals
OMAP1: enable GENERIC_IRQ_CHIP
...
|
| | |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into fixes
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
If CONFIG_OMAP_32K_TIMER is not selected and dmtimer is used as clocksource, the
timer stops counting once overflow occurs as it was not set in autoreload mode.
This results into timekeeping failure: for example, 'sleep 1' at the shell after
the timer counter overflow would hang.
This patch sets up autoreload when starting the clocksource timer which fixes
the above issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Since 7203f8a48bb63015ebe58a6f2a38aec1cb208b9d (arm: mach-omap2: remove
NULL board_mux from board files) NULL board_mux is defined in mux.h.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Use kstrdup rather than duplicating its implementation
The semantic patch that makes this output is available
in scripts/coccinelle/api/kstrdup.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The pointer "va" returned from "phys_to_virt(pa)" is never used in
"sgtable_fill_kmalloc()".So,it is safe to remove this set-but-unused variable.
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Machine database already updated:
http://www.arm.linux.org.uk/developer/machines/list.php?id=3284
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add missing definitions for the AM3505/3517 UART4 such
as DMAs, INTs and base address.
Signed-of-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | |\ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into fixes
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
omap_sr_disable_reset_volt is called with irqs off in omapx_enter_sleep,
as part of idle sequence, this eventually calls sr_disable and
pm_runtime_put_sync. pm_runtime_put_sync calls rpm_idle, which will
enable interrupts in order to call the callback. In this short interval
when interrupts are enabled, scenarios such as the following can occur:
while interrupts are enabled, the timer interrupt that is supposed to
wake the device out of idle occurs and is acked, so when the CPU finally
goes to off, the timer is already gone, missing a wakeup event.
Further, as the documentation for runtime states:"
However, subsystems can use the pm_runtime_irq_safe() helper function
to tell the PM core that a device's ->runtime_suspend() and ->runtime_resume()
callbacks should be invoked in atomic context with interrupts disabled
(->runtime_idle() is still invoked the default way)."
Hence, replace pm_runtime_put_sync with pm_runtime_put_sync_suspend
to invoke the suspend handler and shut off the fclk for SmartReflex
module instead of using the idle handler in interrupt disabled context.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Colin Cross <ccross@google.com>
[khilman@ti.com: minor Subject edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Board code should not touch omap_device internals. To get the MPU/IVA devices,
use existing APIs: omap2_get_mpu_device(), omap2_get_iva_device().
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
OMAP1 needs this also since GPIO driver (common for all OMAPs) is
being converted to use generic IRQ chip.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
SmartReflex should be disabled while entering low power mode due to
a) SmartReflex values are not defined for retention voltage, further
b) with SmartReflex enabled, if CPU enters lower c-states, FSM will try
to bump the voltage to current OPP's voltage for which it has entered c-state;
hence SmartReflex needs to be disabled for MPU, CORE and IVA voltage
domains in idle path before enabling auto retention voltage achievement
on the device.
However, since the current pm_runtime setup for SmartReflex devices are
setup to allow callbacks to be invoked with interrupts enabled, calling
SmartReflex enable/disable from other contexts such as idle paths
where preemption is disabled causes warnings such as the following
indicating of a potential race.
[ 82.023895] [<c04d079c>] (__irq_svc+0x3c/0x120) from [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c)
[ 82.023895] [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c) from [<c0323234>] (rpm_callback+0x4c/0x68)
[ 82.023956] [<c0323234>] (rpm_callback+0x4c/0x68) from [<c0323f7c>] (rpm_resume+0x338/0x53c)
[ 82.023956] [<c0323f7c>] (rpm_resume+0x338/0x53c) from [<c03243f4>] (__pm_runtime_resume+0x48/0x60)
[ 82.023986] [<c03243f4>] (__pm_runtime_resume+0x48/0x60) from [<c008aee0>] (sr_enable+0xa8/0x19c)
[ 82.023986] [<c008aee0>] (sr_enable+0xa8/0x19c) from [<c008b2fc>] (omap_sr_enable+0x50/0x90)
[ 82.024017] [<c008b2fc>] (omap_sr_enable+0x50/0x90) from [<c00888c0>] (omap4_enter_sleep+0x138/0x168)
Instead, we use pm_runtime_irq_safe to tell the PM core that callbacks can be
invoked in interrupt disabled contexts.
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
CONFIG_PM is no longer a user-selectable Kconfig option. Rather it is
automatically enabled if either CONFIG_SUSPEND or CONFIG_RUNTIME_PM is
enabled, so having a 'select PM' here is redunant when 'select
CONFIG_PM_RUNTIME' is present.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Builds for multi-OMAP2 (e.g., OMAP2420 with OMAP2430) with
CONFIG_ARCH_OMAP4=n fail with the following errors:
arch/arm/mach-omap2/built-in.o: In function `_enable_module':
arch/arm/mach-omap2/omap_hwmod.c:701: undefined reference to `omap4_cminst_module_enable'
arch/arm/mach-omap2/built-in.o: In function `_disable_module':
arch/arm/mach-omap2/omap_hwmod.c:726: undefined reference to `omap4_cminst_module_disable'
arch/arm/mach-omap2/built-in.o: In function `_wait_target_disable':
arch/arm/mach-omap2/omap_hwmod.c:1179: undefined reference to `omap4_cminst_wait_module_idle'
This is probably due to the preprocessor directives in
arch/arm/plat-omap/include/plat/cpu.h that convert some cpu_is_omap*()
expressions from preprocessor directives into something that is only
resolvable during runtime, if multiple OMAP2 build targets are
selected.
Thanks to Tony Lindgren <tony@atomide.com> for reporting.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |_|_|/ /
| | |/| | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Commit b22f954 (OMAP4: Move common twl6030 configuration to twl-common)
caused compile failures for code for OMAP arch which is not selected by
the config.
Fixes issues like:
With CONFIG_ARCH_OMAP3=y and CONFIG_ARCH_OMAP4=n, I'm getting this:
arch/arm/mach-omap2/built-in.o:(.data+0xf99c): undefined reference to `omap4430_phy_init'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a0): undefined reference to `omap4430_phy_exit'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a4): undefined reference to `omap4430_phy_power'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a8): undefined reference to `omap4430_phy_set_clk'
arch/arm/mach-omap2/built-in.o:(.data+0xf9ac): undefined reference to `omap4430_phy_suspend'
Fix the problem by moving the code to ifdef sections for omap3 and omap4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | |\ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Instead of setting up a match interrupt for 'current_time + delta'
on ->set_next_event(), program timer 0 to count down from 'delta - 1'
and trigger an interrupt when it reaches zero.
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Currently, arch-mmp/time.c uses timer 0 both as a clocksource timer
and as a clockevent timer, the latter by setting up a comparator
interrupt to match on 'current_time + delta'. This is problematic
if delta is small enough, as that can lead to 'current_time + delta'
already being in the past when comparator setup has finished, leading
to the requested event not triggering.
As there is also a silicon issue that requires stopping a timer's
counter while writing to one of its match registers, we'll switch to
using two separate timers -- timer 0 as clockevent timer, which we'll
start and stop on every invocation of ->set_next_event(), and timer 1
as clocksource timer, which will be free-running.
This first patch enables timer 1 on boot, so that we can use it as
clocksource timer.
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Move definitions from mfp-gplugd.h to mfp-pxa168.h as they aren't
gplugD specific.
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
| | | |/ / / / /
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This got added in:
commit ef6c84454f8567d4968c210d7d194fb711ed3739
Author: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Wed Nov 24 11:54:25 2010 +0800
ARM: pxa: add iwmmx support for PJ4
which does:
- mrc p15, 0, r2, c15, c1, 0
- orr r2, r2, #0x3 @ enable access to CP0 and CP1
- mcr p15, 0, r2, c15, c1, 0
+ @ enable access to CP0 and CP1
+ XSC(mrc p15, 0, r2, c15, c1, 0)
+ XSC(orr r2, r2, #0x3)
+ XSC(mcr p15, 0, r2, c15, c1, 0)
but then later does:
- mrc p15, 0, r4, c15, c1, 0
- orr r4, r4, #0x3 @ enable access to CP0 and CP1
- mcr p15, 0, r4, c15, c1, 0
+ @ enable access to CP0 and CP1
+ XSC(mrc p15, 0, r4, c15, c1, 0)
+ XSC(orr r4, r4, #0xf)
+ XSC(mcr p15, 0, r4, c15, c1, 0)
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by Haojian <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
| | |\ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.pengutronix.de/git/imx/linux-2.6 into fixes
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Commit fad107086d5a869c1c07e5bb35b7b57a10ecf578 fixed the wrong test for MX51
as the MX51 addresses are wrong for MX50 and MX53 but now it's MX51 only,
UART_PADDR is not defined anymore when building for MX50/MX53.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
irq_to_gpio() is being called on a GPIO so change to using
gpio_to_irq() instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| | | |\| | | | | |
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
If the DPLL is already enabled, don't try to enable it again.
Since write to the DPLL control register will make the DPLL
reset and which will cause some issues when some child module
are sourced from this DPLL.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Request for comment and commit.
From: T. Mehnert <t.mehnert@eckelmann.de>
Date: Mon, 4 Jul 2011 15:53:30 +0200
Subject: [PATCH] i.MX25 GPT clock fix: ensure correct the clock source
This patch ensures, that Linux will take the correct clock source (AHB_DIV)
for gpt in the ARM i.MX25 implementation. The currect code depends on the reset
defaults of the CCM_MCR register. So on some boards it could happen that the
UPLL is used for clock source, which results in faulty time behavior in Linux.
In this case all delays or sleeps will will be faktor 1.8 too long.
Signed-off-by: Torsten Mehnert <t.mehnert@eckelmann.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
On MX51 Babbage board the RTS/CTS pins are not used on UART2 port.
Fix the registration of this port.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Current code is assuming that gpio_get_value() is returning 0 or 1 but it
should be checking if the value is 0 or not. Not doing it properly is breaking
the detection of the board (and thus the reboot of efika mx to2) when using
the new mxc gpio driver, which relies on basic mmio gpio.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
