| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Enable Power Management feature on device tree, including MPC8536,
MPC8544, MPC8548, MPC8572, P1010, P1020, P1021, P1022, P2020, P2041,
P3041, T104X, T1024.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240119203911.3143928-1-Frank.Li@nxp.com
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since commit eca70102cfb1 ("net: dsa: felix: add support for changing
DSA master") included in kernel v6.1, the driver supports 2 CPU ports,
and they can be put in a LAG, for example (see
Documentation/networking/dsa/configuration.rst for more details).
Defining the second CPU port in the device tree should not cause any
compatibility issue, because the default CPU port was &seville_port8
before this change, and still is &seville_port8 now (the numerically
first CPU port is used by default).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On board rev A, the network interface labels for the switch ports
written on the front panel are different than on rev B and later.
This patch fixes network interface names for the switch ports according
to labels that are written on the front panel of the board rev B.
They start from ETH3 and end at ETH10.
This patch also introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
Fixes: e69eb0824d8c ("powerpc: dts: t1040rdb: add ports for Seville Ethernet switch")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220121091447.3412907-1-bigunclemax@gmail.com
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Define the network interface names for the switch ports and hook them up
to the 2 QSGMII PHYs that are onboard.
A conscious decision was taken to go along with the numbers that are
written on the front panel of the board and not with the hardware
numbers of the switch chip ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Improve the DTS files by removing all the leading "0x" and zeros to
fix the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were
resolved, namely setting unit-address to lower case, and adding a
whitespace before the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove
leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
| |
|
|
|
|
|
|
|
|
|
| |
Describe the PHY topology for all configurations supported by each board
Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Igal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>
|
| |
|
|
|
|
|
|
|
| |
Also add nodes and properties for thermal management support. Meanwhile
preprocessor support is needed using thermal of framework.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
It makes no sense that some Freescale device tree files are in fsl
directory while some others not. This patch move Freescale device tree
files into fsl folder. To do that the following two steps are made:
- Move Freescale device tree files into fsl folder.
- Update the include path in these files from "fsl/*.dtsi" to "*.dtsi".
Please add "fsl/" prefix when you make dtb using Makefile.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
[scottwood: fixed cuImage rule]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
