summaryrefslogtreecommitdiffstats
path: root/arch
Commit message (Collapse)AuthorAgeFilesLines
* ARM: nomadik: move GPIO and pinctrl to device treeLinus Walleij2013-01-282-4/+69
| | | | | | | | | This moves the instances of the Nomadik pin controller and the Nomadik GPIO blocks (also handled by the GPIO driver) over to the device tree. A new compatible string is added to the pin control driver in the process. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: nomadik: add FSMC NANDLinus Walleij2013-01-282-0/+53
| | | | | | | | | | | | | | | This adds the FSMC NAND driver and flash partitions to the Nomadik device tree. The only compatible string accepted by this driver is currently "st,spear600-fsmc-nand" which is inappropriate for this system, so this patch adds the compatible value "stericsson,fsmc-nand" as well. Cc: linux-mtd@vger.kernel.org Cc: David Woodhouse <dwmw2@infradead.org> Cc: Artem Bityutskiy <dedekind1@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: nomadik: move remaining PrimeCells to device treeLinus Walleij2013-01-282-2/+21
| | | | | | | The two remaining PrimeCells, RNG and RTC, are migrated to the device tree for device tree boot. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: nomadik: move pin maps to cpu fileLinus Walleij2013-01-282-45/+44
| | | | | | | | Move the pinctrl maps over to the CPU file and register them right before the pin controller itself. This way the pinmaps will also benefit the device tree boot. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: nomadik: initial devicetree supportLinus Walleij2013-01-287-1/+188
| | | | | | | | | | | Support basic device tree boot on the Nomadik. Implement the support in the cpu file with the intent of deleting the board files later. At this stage IRQ controllers, system timer, l2x0 cache, UARTs and thus console boot is fully functional. Patch out the code adding devices by initcalls for now so as not to disturb the boot. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ARM: nomadik: move last custom calls to pinctrlLinus Walleij2013-01-282-12/+9
| | | | | | | | | | The I2C pins were still set up using custom nmk_* calls, move these to use the pinctrl mapping table instead. There was also a remaining call to turn the Ethernet pin to GPIO, and this is now done implicitly by the GPIO-to-pinctrl range translation calls. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux ↵Olof Johansson2013-01-14138-1899/+112
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | into next/cleanup From Rob Herring: Initial irqchip init infrastructure and GIC and VIC clean-ups This creates irqchip initialization infrastructure from Thomas Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips and adapted to use the new infrastructure. All DT enabled platforms using GIC and VIC are converted over to use the new irqchip_init. * tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux: irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h ARM: picoxcell: use common irqchip_init function ARM: spear: use common irqchip_init function irqchip: Move ARM VIC to drivers/irqchip ARM: samsung: remove unused tick.h ARM: remove unneeded vic.h includes ARM: remove mach .handle_irq for VIC users ARM: VIC: set handle_arch_irq in VIC initialization ARM: VIC: shrink down vic.h irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h ARM: use common irqchip_init for GIC init irqchip: Move ARM GIC to drivers/irqchip ARM: remove mach .handle_irq for GIC users ARM: GIC: set handle_arch_irq in GIC initialization ARM: GIC: remove direct use of gic_raise_softirq ARM: GIC: remove assembly ifdefs from gic.h ARM: mach-ux500: use SGI0 to wake up the other core arm: add set_handle_irq() to register the parent IRQ controller handler function irqchip: add basic infrastructure irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS Fixed up massive merge conflicts with the timer cleanup due to adjacent changes: Signed-off-by: Olof Johansson <olof@lixom.net> Conflicts: arch/arm/mach-bcm/board_bcm.c arch/arm/mach-cns3xxx/cns3420vb.c arch/arm/mach-ep93xx/adssphere.c arch/arm/mach-ep93xx/edb93xx.c arch/arm/mach-ep93xx/gesbc9312.c arch/arm/mach-ep93xx/micro9.c arch/arm/mach-ep93xx/simone.c arch/arm/mach-ep93xx/snappercl15.c arch/arm/mach-ep93xx/ts72xx.c arch/arm/mach-ep93xx/vision_ep9307.c arch/arm/mach-highbank/highbank.c arch/arm/mach-imx/mach-imx6q.c arch/arm/mach-msm/board-dt-8960.c arch/arm/mach-netx/nxdb500.c arch/arm/mach-netx/nxdkn.c arch/arm/mach-netx/nxeb500hmi.c arch/arm/mach-nomadik/board-nhk8815.c arch/arm/mach-picoxcell/common.c arch/arm/mach-realview/realview_eb.c arch/arm/mach-realview/realview_pb1176.c arch/arm/mach-realview/realview_pb11mp.c arch/arm/mach-realview/realview_pba8.c arch/arm/mach-realview/realview_pbx.c arch/arm/mach-socfpga/socfpga.c arch/arm/mach-spear13xx/spear1310.c arch/arm/mach-spear13xx/spear1340.c arch/arm/mach-spear13xx/spear13xx.c arch/arm/mach-spear3xx/spear300.c arch/arm/mach-spear3xx/spear310.c arch/arm/mach-spear3xx/spear320.c arch/arm/mach-spear3xx/spear3xx.c arch/arm/mach-spear6xx/spear6xx.c arch/arm/mach-tegra/board-dt-tegra20.c arch/arm/mach-tegra/board-dt-tegra30.c arch/arm/mach-u300/core.c arch/arm/mach-ux500/board-mop500.c arch/arm/mach-ux500/cpu-db8500.c arch/arm/mach-versatile/versatile_ab.c arch/arm/mach-versatile/versatile_dt.c arch/arm/mach-versatile/versatile_pb.c arch/arm/mach-vexpress/v2m.c include/asm-generic/vmlinux.lds.h
| * irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.hRob Herring2013-01-1213-50/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have VIC moved to drivers/irqchip and all VIC DT init for platforms using irqchip_init, move gic.h and update the remaining includes. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ryan Mallon <rmallon@gmail.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Alessandro Rubini <rubini@unipv.it> Acked-by: Linus Walleij <linus.walleij@linaro.org> Cc: STEricsson <STEricsson_nomadik_linux@list.st.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: linux-samsung-soc@vger.kernel.org
| * ARM: picoxcell: use common irqchip_init functionRob Herring2013-01-121-12/+2
| | | | | | | | | | Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Jamie Iles <jamie@jamieiles.com>
| * ARM: spear: use common irqchip_init functionRob Herring2013-01-126-33/+8
| | | | | | | | | | | | | | | | | | | | Convert spear DT irq initialization over to use common irqchip_init function. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Viresh Kumar <viresh.linux@gmail.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
| * irqchip: Move ARM VIC to drivers/irqchipRob Herring2013-01-123-500/+0
| | | | | | | | | | | | | | | | Now that we have drivers/irqchip, move VIC irqchip to drivers/irqchip. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de>
| * ARM: samsung: remove unused tick.hRob Herring2013-01-122-55/+0
| | | | | | | | | | | | | | | | | | Remove tick.h on s5p64x0 and s5pv210 as they are unused. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: linux-samsung-soc@vger.kernel.org
| * ARM: remove unneeded vic.h includesRob Herring2013-01-1236-37/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Numerous includes of asm/hardware/vic.h aren't needed, so remove them. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ryan Mallon <rmallon@gmail.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Hubert Feurstein <hubert.feurstein@contec.at> Cc: Alessandro Rubini <rubini@unipv.it> Acked-by: Linus Walleij <linus.walleij@linaro.org> Cc: STEricsson <STEricsson_nomadik_linux@list.st.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Acked-By: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: linux-samsung-soc@vger.kernel.org Cc: patches@opensource.wolfsonmicro.com Acked-by: Arnd Bergmann <arnd@arndb.de>
| * ARM: remove mach .handle_irq for VIC usersRob Herring2013-01-1241-87/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the VIC initialization sets up the handle_arch_irq pointer, we can remove it for all machines and make it static. Move vic_handle_irq to avoid a forward declaration. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Ryan Mallon <rmallon@gmail.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Hubert Feurstein <hubert.feurstein@contec.at> Cc: Alessandro Rubini <rubini@unipv.it> Cc: STEricsson <STEricsson_nomadik_linux@list.st.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Arnd Bergmann <arnd@arndb.de>
| * ARM: VIC: set handle_arch_irq in VIC initializationRob Herring2013-01-121-0/+1
| | | | | | | | | | | | | | | | Set handle_arch_irq to vic_handle_irq. Only the first VIC initialized can setup the handler. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Olof Johansson <olof@lixom.net>
| * ARM: VIC: shrink down vic.hRob Herring2013-01-122-21/+19
| | | | | | | | | | | | | | | | | | | | | | | | Move all register defines except VIC_INT_ENABLE and VIC_INT_ENABLE_CLEAR which are used by Samsung. With multi irq handler, vic.h is not included in assembly any more, so we can remove the assembly ifdefs. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Olof Johansson <olof@lixom.net>
| * irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.hRob Herring2013-01-1236-85/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have GIC moved to drivers/irqchip and all GIC DT init for platforms using irqchip_init, move gic.h and update the remaining includes. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Anton Vorontsov <avorontsov@mvista.com> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Cc: Tony Lindgren <tony@atomide.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Viresh Kumar <viresh.linux@gmail.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Samuel Ortiz <sameo@linux.intel.com>
| * ARM: use common irqchip_init for GIC initRob Herring2013-01-1218-145/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert all GIC DT initialization over to use common irqchip_init function. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Cc: Tony Lindgren <tony@atomide.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Viresh Kumar <viresh.linux@gmail.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org>
| * irqchip: Move ARM GIC to drivers/irqchipRob Herring2013-01-123-826/+0
| | | | | | | | | | | | | | | | | | Now that we have drivers/irqchip, move GIC irqchip to drivers/irqchip. This is necessary to share the GIC with arm and arm64. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de>
| * ARM: remove mach .handle_irq for GIC usersRob Herring2013-01-1246-70/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the GIC initialization sets up the handle_arch_irq pointer, we can remove it for all machines and make it static. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Anton Vorontsov <avorontsov@mvista.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Acked-by: Tony Lindgren <tony@atomide.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Acked-by: Stephen Warren <swarren@nvidia.com> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Arnd Bergmann <arnd@arndb.de>
| * ARM: GIC: set handle_arch_irq in GIC initializationRob Herring2013-01-101-0/+3
| | | | | | | | | | | | | | | | Set handle_arch_irq to gic_handle_irq. Only the first GIC initialized can setup the handler. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Olof Johansson <olof@lixom.net>
| * ARM: GIC: remove direct use of gic_raise_softirqRob Herring2013-01-1018-57/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In preparation of moving gic code to drivers/irqchip, remove the direct platform dependencies on gic_raise_softirq. Move the setup of smp_cross_call into the gic code and use arch_send_wakeup_ipi_mask function to trigger wake-up IPIs. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Magnus Damm <magnus.damm@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Shiraz Hashim <shiraz.hashim@st.com> Acked-by: Stephen Warren <swarren@nvidia.com> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org> Acked-by: Olof Johansson <olof@lixom.net>
| * ARM: GIC: remove assembly ifdefs from gic.hRob Herring2013-01-101-6/+0
| | | | | | | | | | | | | | | | | | With multi irq handler and all GIC users converted to it, we don't need asm/hardware/gic.h to be included in assembly. Clean-up ifdefs and unnecessary includes. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Olof Johansson <olof@lixom.net>
| * ARM: mach-ux500: use SGI0 to wake up the other coreSrinidhi Kasagar2013-01-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | The commit 7d28e3eaa1a8e951251b942e7220f97114bd73b9 ("ARM: ux500: wake secondary cpu via resched") makes use of schedule IPI to wake up the secondary core which seems incorrect. Rather use SGI0. Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Olof Johansson <olof@lixom.net>
| * arm: add set_handle_irq() to register the parent IRQ controller handler functionThomas Petazzoni2013-01-102-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In order to allow irqchip drivers to register their IRQ handling function as the parent IRQ controller handler function, we provide a convenience function. This will avoid poking directly into the global handle_arch_irq variable. Suggested by Arnd Bergmann. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> [Rob Herring: remove warning. 1st one to initialize wins.] Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Olof Johansson <olof@lixom.net>
* | Merge tag 'vt8500/timer' of git://server.prisktech.co.nz/git/linuxwmt into ↵Olof Johansson2013-01-145-181/+3
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | next/cleanup From Tony Prisk: Move arch-vt8500/timer.c to drivers/clocksource/vt8500-timer.c * tag 'vt8500/timer' of git://server.prisktech.co.nz/git/linuxwmt: timer: vt8500: Move timer code to drivers/clocksource Signed-off-by: Olof Johansson <olof@lixom.net>
| * | timer: vt8500: Move timer code to drivers/clocksourceTony Prisk2013-01-145-186/+3
| | | | | | | | | | | | | | | | | | | | | This patch moves arch-vt8500/timer.c into drivers/clocksource and updates the necessary Kconfig/Makefile options. Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
* | | Merge branch 'clocksource/cleanup' into next/cleanupOlof Johansson2013-01-14333-1285/+1209
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clockevent cleanup series from Shawn Guo. Resolved move/change conflict in mach-pxa/time.c due to the sys_timer cleanup. * clocksource/cleanup: clocksource: use clockevents_config_and_register() where possible ARM: use clockevents_config_and_register() where possible clockevents: export clockevents_config_and_register for module use + sync to Linux 3.8-rc3 Signed-off-by: Olof Johansson <olof@lixom.net> Conflicts: arch/arm/mach-pxa/time.c
| * | | ARM: use clockevents_config_and_register() where possibleShawn Guo2013-01-1425-209/+53
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The clockevent core is able to figure out the best mult and shift, calculate min_delta_ns and max_delta_ns, with the necessary info passed into clockevents_config_and_register(). Use this combined configure and register function where possible to make the codes less error prone and gain some positive diff stat. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Tested-by: Roland Stigge <stigge@antcom.de> Acked-by: Eric Miao <eric.y.miao@gmail.com> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: David Brown <davidb@codeaurora.org> Tested-by: Tony Lindgren <tony@atomide.com> Acked-by: Barry Song <baohua.song@csr.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tony Prisk <linux@prisktech.co.nz> Cc: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Wan ZongShun <mcuos.com@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jason Cooper <jason@lakedaemon.net> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Olof Johansson <olof@lixom.net>
| * | Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds2013-01-097-22/+40
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM fixes from Russell King. * 'fixes' of git://git.linaro.org/people/rmk/linux-arm: ARM: 7616/1: cache-l2x0: aurora: Use writel_relaxed instead of writel ARM: 7615/1: cache-l2x0: aurora: Invalidate during clean operation with WT enable ARM: 7614/1: mm: fix wrong branch from Cortex-A9 to PJ4b ARM: 7612/1: imx: Do not select some errata that depends on !ARCH_MULTIPLATFORM ARM: 7611/1: VIC: fix bug in VIC irqdomain code ARM: 7610/1: versatile: bump IRQ numbers ARM: 7609/1: disable errata work-arounds which access secure registers ARM: 7608/1: l2x0: Only set .set_debug on PL310 r3p0 and earlier
| | * | ARM: 7616/1: cache-l2x0: aurora: Use writel_relaxed instead of writelGregory CLEMENT2013-01-071-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The use of writel instead of writel_relaxed lead to deadlock in some situation (SMP on Armada 370 for instance). The use of writel_relaxed as it was done in the rest of this driver fixes this bug. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7615/1: cache-l2x0: aurora: Invalidate during clean operation with WT ↵Gregory CLEMENT2013-01-071-8/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | enable This patch fixes a bug for Aurora L2 cache controller when the write-through mode is enable. For the clean operation even if we don't have to flush the lines we still need to invalidate them. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7614/1: mm: fix wrong branch from Cortex-A9 to PJ4bHaojian Zhuang2013-01-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If CONFIG_ARCH_MULTIPLATFORM & CONFIG_ARCH_MVEBU are both enabled, __v7_pj4b_setup is added between __v7_ca9mp_setup and __v7_setup. But there's no jump instruction added. If the chip is Cortex A5/A9, it goes through __v7_pj4b_setup also. It results in system hang. Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7612/1: imx: Do not select some errata that depends on !ARCH_MULTIPLATFORMFabio Estevam2013-01-061-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 62e4d357a (ARM: 7609/1: disable errata work-arounds which access secure registers) ARM_ERRATA_743622/751472 depends on !ARCH_MULTIPLATFORM. Since imx has been converted to multiplatform, the following warning happens: $ make imx_v6_v7_defconfig warning: (SOC_IMX6Q && ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_751472 which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM) warning: (SOC_IMX6Q && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_743622 which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM) warning: (SOC_IMX6Q && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_743622 which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM) warning: (SOC_IMX6Q && ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_751472 which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM) Recommended approach is to remove ARM_ERRATA_743622/751472 from being selected by SOC_IMX6Q and apply such workarounds into the bootloader. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7611/1: VIC: fix bug in VIC irqdomain codeLinus Walleij2013-01-021-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VIC irqdomain code added in commit 07c9249f1fa90cc8189bed44c0bcece664596a72 "ARM: 7554/1: VIC: use irq_domain_add_simple()" Had two bugs: 1) It didn't call irq_create_mapping() once on each valid irq source in the slowpath when registering the controller. 2) It passed a -1 as IRQ offset for the DT case, whereas 0 should be passed as invalid IRQ instead. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7610/1: versatile: bump IRQ numbersLinus Walleij2013-01-021-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Versatile starts to register Linux IRQ numbers from offset 0 which is illegal, since this is NO_IRQ. Bump all hard-coded IRQs by 32 to get rid of the problem. Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7609/1: disable errata work-arounds which access secure registersRob Herring2013-01-023-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In order to support secure and non-secure platforms in multi-platform kernels, errata work-arounds that access secure only registers need to be disabled. Make all the errata options that fit in this category depend on !CONFIG_ARCH_MULTIPLATFORM. This will effectively remove the errata options as platforms are converted over to multi-platform. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7608/1: l2x0: Only set .set_debug on PL310 r3p0 and earlierRob Herring2013-01-021-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PL310 errata work-arounds using .set_debug function are only needed on r3p0 and earlier, so check the rev and only set .set_debug on older revs. Avoiding debug register accesses fixes aborts on non-secure platforms like highbank. It is assumed that non-secure platforms needing these work-arounds have already implemented .set_debug with secure monitor calls. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| * | | Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds2013-01-0843-137/+305
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull ARM SoC fixes from Olof Johansson: "People are back from the holiday breaks, and it shows. Here are a bunch of fixes for a number of platforms: - A couple of small fixes for Nomadik - A larger set of changes for kirkwood/mvebu - uart driver selection, dt clocks, gpio-poweroff fixups, a few __init annotation fixes and some error handling improvement in their xor dma driver. - i.MX had a couple of minor fixes (and a critical one for flexcan2 clock setup) - MXS has a small board fix and a framebuffer bugfix - A set of fixes for Samsung Exynos, fixing default bootargs and some Exynos5440 clock issues - A set of OMAP changes including PM fixes and a few sparse warning fixups All in all a bit more positive code delta than we'd ideally want to see here, mostly from the OMAP PM changes, but nothing overly crazy." * tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits) ARM: clps711x: Fix bad merge of clockevents setup ARM: highbank: save and restore L2 cache and GIC on suspend ARM: highbank: add a power request clear ARM: highbank: fix secondary boot and hotplug ARM: highbank: fix typos with hignbank in power request functions ARM: dts: fix highbank cpu mpidr values ARM: dts: add device_type prop to cpu nodes on Calxeda platforms ARM: mx5: Fix MX53 flexcan2 clock ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array pinctrl: mvebu: make pdma clock on dove mandatory ARM: Dove: Add pinctrl clock to DT dma: mv_xor: fix error handling for clocks dma: mv_xor: fix error handling of mv_xor_channel_add() arm: mvebu: Add missing ; for cpu node. arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces arm: mvebu: Armada XP MV78230 has two cores, not one clk: mvebu: Remove inappropriate __init tagging ARM: Kirkwood: Use fixed-regulator instead of board gpio call ARM: Kirkwood: Fix missing sdio clock ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers ...
| | * \ \ Merge tag 'omap-for-v3.8-rc2/fixes-signed-v2' of ↵Olof Johansson2013-01-0811-38/+132
| | |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes From Tony Lindgren: The biggest change is a fix to deal with different power state on omap2 registers that causes issues trying to use common PM code. Also fix few incorrect registers, and an issue for omap1 USB, and few sparse fixes for issues that sneaked in with all the clean-up. * tag 'omap-for-v3.8-rc2/fixes-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array ARM: OMAP1: fix USB configuration use-after-release ARM: OMAP2/3: PRM: fix bogus OMAP2xxx powerstate return values ARM: OMAP3: clock data: Add missing enable/disable for EMU clock ARM: OMAP4: PRM: Correct wrong instance usage for reading reset sources ARM: OMAP4: PRM: fix RSTTIME and RSTST offsets ARM: OMAP4: PRM: Correct reset source map ARM: OMAP: SRAM: resolve sparse warnings ARM: OMAP AM33xx: hwmod data: resolve sparse warnings ARM: OMAP: 32k counter: resolve sparse warnings Signed-off-by: Olof Johansson <olof@lixom.net>
| | | * | | ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs arrayPantelis Antoniou2013-01-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The IRQ array must be terminated by -1 and not by -1+OMAP_INTC_START This led to having a resource list of 100s of IRQs. Looks like this was caused by commit a2cfc509 (ARM: OMAP3+: hwmod: Add AM33XX HWMOD data) that probably had some search and replace updates done for the patch for sparse irq support. Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Acked-by: Paul Walmsley <paul@pwsan.com> [tony@atomide.com: updated wit information about the breaking commit] Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | ARM: OMAP1: fix USB configuration use-after-releaseAaro Koskinen2013-01-032-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All boards, except Amstrad E3, mark USB config with __initdata. As a result, when you compile USB into modules, they will try to refer already released platform data and the behaviour is undefined. For example on Nokia 770, I get the following kernel panic when modprobing ohci-hcd: [ 3.462158] Unable to handle kernel paging request at virtual address e7fddef0 [ 3.477050] pgd = c3434000 [ 3.487365] [e7fddef0] *pgd=00000000 [ 3.498535] Internal error: Oops: 80000005 [#1] ARM [ 3.510955] Modules linked in: ohci_hcd(+) [ 3.522705] CPU: 0 Not tainted (3.7.0-770_tiny+ #5) [ 3.535552] PC is at 0xe7fddef0 [ 3.546508] LR is at ohci_omap_init+0x5c/0x144 [ohci_hcd] [ 3.560272] pc : [<e7fddef0>] lr : [<bf003140>] psr: a0000013 [ 3.560272] sp : c344bdb0 ip : c344bce0 fp : c344bdcc [ 3.589782] r10: 00000001 r9 : 00000000 r8 : 00000000 [ 3.604553] r7 : 00000026 r6 : 000000de r5 : c0227300 r4 : c342d620 [ 3.621032] r3 : e7fddef0 r2 : c048b880 r1 : 00000000 r0 : 0000000a [ 3.637786] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 3.655822] Control: 0005317f Table: 13434000 DAC: 00000015 [ 3.672790] Process modprobe (pid: 425, stack limit = 0xc344a1b8) [ 3.690643] Stack: (0xc344bdb0 to 0xc344c000) [ 3.707031] bda0: bf0030e4 c342d620 00000000 c049e62c [ 3.727905] bdc0: c344be04 c344bdd0 c0150ff0 bf0030f4 bf001b88 00000000 c048a4ac c345b020 [ 3.748870] bde0: c342d620 00000000 c048a468 bf003968 00000001 bf006000 c344be34 c344be08 [ 3.769836] be00: bf001bf0 c0150e48 00000000 c344be18 c00b9bfc c048a478 c048a4ac bf0037f8 [ 3.790985] be20: c012ca04 c000e024 c344be44 c344be38 c012d968 bf001a84 c344be64 c344be48 [ 3.812164] be40: c012c8ac c012d95c 00000000 c048a478 c048a4ac bf0037f8 c344be84 c344be68 [ 3.833740] be60: c012ca74 c012c80c 20000013 00000000 c344be88 bf0037f8 c344beac c344be88 [ 3.855468] be80: c012b038 c012ca14 c38093cc c383ee10 bf0037f8 c35be5a0 c049d5e8 00000000 [ 3.877166] bea0: c344bebc c344beb0 c012c40c c012aff4 c344beec c344bec0 c012bfc0 c012c3fc [ 3.898834] bec0: bf00378c 00000000 c344beec bf0037f8 00067f39 00000000 00005c44 c000e024 [ 3.920837] bee0: c344bf14 c344bef0 c012cd54 c012befc c04ce080 00067f39 00000000 00005c44 [ 3.943023] bf00: c000e024 bf006000 c344bf24 c344bf18 c012db14 c012ccc0 c344bf3c c344bf28 [ 3.965423] bf20: bf00604c c012dad8 c344a000 bf003834 c344bf7c c344bf40 c00087ac bf006010 [ 3.987976] bf40: 0000000f bf003834 00067f39 00000000 00005c44 bf003834 00067f39 00000000 [ 4.010711] bf60: 00005c44 c000e024 c344a000 00000000 c344bfa4 c344bf80 c004c35c c0008720 [ 4.033569] bf80: c344bfac c344bf90 01422192 01427ea0 00000000 00000080 00000000 c344bfa8 [ 4.056518] bfa0: c000dec0 c004c2f0 01422192 01427ea0 01427ea0 00005c44 00067f39 00000000 [ 4.079406] bfc0: 01422192 01427ea0 00000000 00000080 b6e11008 014221aa be941fcc b6e1e008 [ 4.102569] bfe0: b6ef6300 be941758 0000e93c b6ef6310 60000010 01427ea0 00000000 00000000 [ 4.125946] Backtrace: [ 4.143463] [<bf0030e4>] (ohci_omap_init+0x0/0x144 [ohci_hcd]) from [<c0150ff0>] (usb_add_hcd+0x1b8/0x61c) [ 4.183898] r6:c049e62c r5:00000000 r4:c342d620 r3:bf0030e4 [ 4.205596] [<c0150e38>] (usb_add_hcd+0x0/0x61c) from [<bf001bf0>] (ohci_hcd_omap_drv_probe+0x17c/0x224 [ohci_hcd]) [ 4.248138] [<bf001a74>] (ohci_hcd_omap_drv_probe+0x0/0x224 [ohci_hcd]) from [<c012d968>] (platform_drv_probe+0x1c/0x20) [ 4.292144] r8:c000e024 r7:c012ca04 r6:bf0037f8 r5:c048a4ac r4:c048a478 [ 4.316192] [<c012d94c>] (platform_drv_probe+0x0/0x20) from [<c012c8ac>] (driver_probe_device+0xb0/0x208) [ 4.360168] [<c012c7fc>] (driver_probe_device+0x0/0x208) from [<c012ca74>] (__driver_attach+0x70/0x94) [ 4.405548] r6:bf0037f8 r5:c048a4ac r4:c048a478 r3:00000000 [ 4.429809] [<c012ca04>] (__driver_attach+0x0/0x94) from [<c012b038>] (bus_for_each_dev+0x54/0x90) [ 4.475708] r6:bf0037f8 r5:c344be88 r4:00000000 r3:20000013 [ 4.500366] [<c012afe4>] (bus_for_each_dev+0x0/0x90) from [<c012c40c>] (driver_attach+0x20/0x28) [ 4.528442] r7:00000000 r6:c049d5e8 r5:c35be5a0 r4:bf0037f8 [ 4.553466] [<c012c3ec>] (driver_attach+0x0/0x28) from [<c012bfc0>] (bus_add_driver+0xd4/0x228) [ 4.581878] [<c012beec>] (bus_add_driver+0x0/0x228) from [<c012cd54>] (driver_register+0xa4/0x134) [ 4.629730] r8:c000e024 r7:00005c44 r6:00000000 r5:00067f39 r4:bf0037f8 [ 4.656738] [<c012ccb0>] (driver_register+0x0/0x134) from [<c012db14>] (platform_driver_register+0x4c/0x60) [ 4.706542] [<c012dac8>] (platform_driver_register+0x0/0x60) from [<bf00604c>] (ohci_hcd_mod_init+0x4c/0x8c [ohci_hcd]) [ 4.757843] [<bf006000>] (ohci_hcd_mod_init+0x0/0x8c [ohci_hcd]) from [<c00087ac>] (do_one_initcall+0x9c/0x174) [ 4.808990] r4:bf003834 r3:c344a000 [ 4.832641] [<c0008710>] (do_one_initcall+0x0/0x174) from [<c004c35c>] (sys_init_module+0x7c/0x194) [ 4.881530] [<c004c2e0>] (sys_init_module+0x0/0x194) from [<c000dec0>] (ret_fast_syscall+0x0/0x2c) [ 4.930664] r7:00000080 r6:00000000 r5:01427ea0 r4:01422192 [ 4.956481] Code: bad PC value [ 4.978729] ---[ end trace 58280240f08342c4 ]--- [ 5.002258] Kernel panic - not syncing: Fatal exception Fix this by taking a copy of the data. Also mark Amstrad E3's data with __initdata to save some memory with multi-board kernels. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com>
| | | * | | Merge tag 'omap-fixes-a2-for-v3.8-rc' of ↵Tony Lindgren2013-01-039-35/+123
| | | |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8-rc2/fixes Some OMAP PRCM and sparse fixes against v3.8-rc1. A basic set of test logs are available here: http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/ The 3730 Beagle XM here has an intermittent failure mounting SD root, but the suspicion right now is that this is due to a failing SD card, rather than any change introduced by these patches. This second version includes a few changes requested by Tony Lindgren.
| | | | * | | ARM: OMAP2/3: PRM: fix bogus OMAP2xxx powerstate return valuesPaul Walmsley2013-01-023-28/+110
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On OMAP2xxx chips, the register bitfields for the PM_PWSTCTRL_*.POWERSTATE and PM_PWSTST_*.LASTSTATEENTERED are different than those used on OMAP3/4. The order is reversed. So, for example, on OMAP2xxx, 0x0 indicates 'ON'; but on OMAP3/4, 0x0 indicates 'OFF'. Similarly, on OMAP2xxx, 0x3 indicates 'OFF', but on OMAP3/4, 0x3 indicates 'ON'. To fix this, we treat the OMAP3/4 values as the powerdomain API values, and create new low-level powerdomain functions for the OMAP2xxx chips which translate between the OMAP2xxx values and the OMAP3/4 values. Without this patch, the conversion of the OMAP2xxx PM code to the functional powerstate code results in a non-booting kernel. Signed-off-by: Paul Walmsley <paul@pwsan.com>
| | | | * | | ARM: OMAP3: clock data: Add missing enable/disable for EMU clockJon Hunter2013-01-021-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ETM/ETB drivers for OMAP3, enable the emu_src_ck clock in order to access the ETM/ETB hardware. The emu_src_ck should enable the EMU clock domain so that the ETM/ETB hardware is accessible. However, currently when enabling the emu_src_ck the EMU clock domain is not being enabled and so the ETM/ETB drivers are failing. Add enable/disable clock functions to enable the EMU clock domain when enabling the emu_src_ck. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
| | | | * | | ARM: OMAP4: PRM: Correct wrong instance usage for reading reset sourcesIvan Khoronzhuk2013-01-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To read reset sources registers we have to use PRM_DEVICE_INST Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
| | | | * | | ARM: OMAP4: PRM: fix RSTTIME and RSTST offsetsNishanth Menon2013-01-021-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | RSTTIME is offset 0x8 and RSTST is offset 0x04 for OMAP4430 and OMAP4460. Signed-off-by: Nishanth Menon <nm@ti.com> [ivan.khoronzhuk@ti.com: ported from k3.4] Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
| | | | * | | ARM: OMAP4: PRM: Correct reset source mapIvan Khoronzhuk2013-01-021-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the map for reset sources register we use defines intended for using with PRM_RSTCTRL register. So fix it. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
| | | | * | | ARM: OMAP: SRAM: resolve sparse warningsPaul Walmsley2013-01-011-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit bb77209432873214a796a70a4539e4ebdf3feb54 ("ARM: OMAP: Move omap2+ specific parts of sram.c to mach-omap2") adds some new sparse warnings: arch/arm/plat-omap/sram.c:43:6: warning: symbol 'omap_sram_push_address' was not declared. Should it be static? arch/arm/plat-omap/sram.c:65:6: warning: symbol 'omap_sram_reset' was not declared. Should it be static? arch/arm/plat-omap/sram.c:73:13: warning: symbol 'omap_map_sram' was not declared. Should it be static? This second version fixes the warnings by including <plat/sram.h>, at Tony's request. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com>
| | | | * | | ARM: OMAP AM33xx: hwmod data: resolve sparse warningsPaul Walmsley2013-01-011-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 70384a6af0914d5dcec034643941e29d3e3e69f7 ("ARM: OMAP3+: hwmod: Add AM33XX HWMOD data for davinci_mdio module") adds two new sparse warnings: arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2518:30: warning: symbol 'am33xx_mdio_addr_space' was not declared. Should it be static? arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2526:26: warning: symbol 'am33xx_cpgmac0__mdio' was not declared. Should it be static? Fix by marking the two new records as static. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: David S. Miller <davem@davemloft.net> Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 14:29:40 +0000