summaryrefslogtreecommitdiffstats
path: root/drivers/iio/magnetometer
Commit message (Collapse)AuthorAgeFilesLines
* iio: magnetometer: mag3110: Add ability to run in continuous modeRichard Tresidder2018-05-121-18/+140
| | | | | | | | | | | | | | Adds the ability to run the Mag3110 in continuous mode to speed up the sampling rate. Depending on the sampling rate requested the device can be put in or out of continuous mode automatically. Shifting out of continuous mode requires a potential 1 / ODR wait which is also implemented. Modified the sleep method when data is not ready to allow for sampling > 50sps to work. Signed-off-by: Richard Tresidder <rtresidd@electromag.com.au> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* iio:magnetometer: Replace magic number 0 by IIO_CHAN_INFO_RAWRodrigo Siqueira2018-03-031-1/+1
| | | | | | | | | | | The function magn_3d_read_raw has a switch statement handling multiple cases per channel. The first case statement uses the magic number 0, which means IIO_CHAN_INFO_RAW. Additionally, the iio_chan_spec for magn_3d_channels is configured to be IIO_CHAN_INFO_RAW. Therefore, this patch replaces the magic number 0 for the appropriate IIO_CHAN_INFO_RAW. Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* iio: magnetometer: ak8975: Add another ACPI IDAndy Shevchenko2017-12-021-0/+1
| | | | | | | Add new ACPI ID for ak9911 as had been found on prototype board. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* Merge tag 'staging-4.15-rc1' of ↵Linus Torvalds2017-11-138-14/+16
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging and IIO updates from Greg KH: "Here is the "big" staging and IIO driver update for 4.15-rc1. Lots and lots of little changes, almost all minor code cleanups as the Outreachy application process happened during this development cycle. Also happened was a lot of IIO driver activity, and the typec USB code moving out of staging to drivers/usb (same commits are in the USB tree on a persistent branch to not cause merge issues.) Overall, it's a wash, I think we added a few hundred more lines than removed, but really only a few thousand were modified at all. All of these have been in linux-next for a while. There might be a merge issue with Al's vfs tree in the pi433 driver (take his changes, they are always better), and the media tree with some of the odd atomisp cleanups (take the media tree's version)" * tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits) staging: lustre: add SPDX identifiers to all lustre files staging: greybus: Remove redundant license text staging: greybus: add SPDX identifiers to all greybus driver files staging: ccree: simplify ioread/iowrite staging: ccree: simplify registers access staging: ccree: simplify error handling logic staging: ccree: remove dead code staging: ccree: handle limiting of DMA masks staging: ccree: copy IV to DMAable memory staging: fbtft: remove redundant initialization of buf staging: sm750fb: Fix parameter mistake in poke32 staging: wilc1000: Fix bssid buffer offset in Txq staging: fbtft: fb_ssd1331: fix mirrored display staging: android: Fix checkpatch.pl error staging: greybus: loopback: convert loopback to use generic async operations staging: greybus: operation: add private data with get/set accessors staging: greybus: loopback: Fix iteration count on async path staging: greybus: loopback: Hold per-connection mutex across operations staging: greybus/loopback: use ktime_get() for time intervals staging: fsl-dpaa2/eth: Extra headroom in RX buffers ...
| * iio: magnetometer: st_magn: add SPI-3wire support to LIS3MDLLorenzo Bianconi2017-10-101-0/+4
| | | | | | | | | | | | | | | | Add SPI Serial Interface Mode (SIM) register information to LIS3MDL magn sensor Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: st_sensors: decouple irq1 configuration parameters from the irq2 onesLorenzo Bianconi2017-10-091-2/+4
| | | | | | | | | | | | | | | | | | | | Separate data-ready configuration parameters for INT1 and INT2 pins in st_sensor_data_ready_irq data structure. That change will be use to properly support LIS2DW12 accel sensor. Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: st_sensors: add register mask for status registerLorenzo Bianconi2017-10-091-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce register mask for data-ready status register since pressure sensors (e.g. LPS22HB) export just two channels (BIT(0) and BIT(1)) and BIT(2) is marked reserved while in st_sensors_new_samples_available() value read from status register is masked using 0x7. Moreover do not mask status register using active_scan_mask since now status value is properly masked and if the result is not zero the interrupt has to be consumed by the driver. This fix an issue on LPS25H and LPS331AP where channel definition is swapped respect to status register. Furthermore that change allows to properly support new devices (e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register to figure out if the interrupt has been generated by the device. Fixes: 97865fe41322 (iio: st_sensors: verify interrupt event to status) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * Merge 4.14-rc4 into staging-nextGreg Kroah-Hartman2017-10-091-0/+4
| |\ | | | | | | | | | | | | | | | We want the staging/iio fixes in here as well to handle merge issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * \ Merge tag 'iio-for-4.15a' of ↵Greg Kroah-Hartman2017-09-258-10/+0
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next Jonathan writes: Round one of new device support, features and cleanup for IIO in the 4.15 cycle. Note there is a misc driver drop in here given we have support in IIO and the feeling is no one will care. A large part of this series is a boiler plate removal series avoiding the need to explicitly provide THIS_MODULE in various locations. It's very dull but touches all drivers. New device support * ad5446 - add ids to support compatible parts DAC081S101, DAC101S101, DAC121S101. - add the dac7512 id and drop the misc driver as feeling is no one is using it (was introduced for a board that is long obsolete) * mt6577 - add bindings for mt2712 which is fully compatible with other supported parts. * st_pressure - add support for LPS33HW and LPS35HW with bindings (ids mostly). New features * ccs811 - Add support for the data ready trigger. * mma8452 - remove artifical restriction on supporting multiple event types at the same time. * tcs3472 - support out of threshold events Core and tree wide cleanup * Use macro magic to remove the need to provide THIS_MODULE as part of struct iio_info or struct iio_trigger_ops. This is similar to work done in a number of other subsystems (e.g. i2c, spi). All drivers are fixed and then the fields in these structures are removed. This will cause build failures for out of tree drivers and any new drivers that cross with this work going into the kernel. Note mostly done with a coccinelle patch, included in the series on the mailing list but not merged as the fields no longer exist in the structures so the any hold outs will cause a build failure. Cleanups * ads1015 - avoid writing config register when it doesn't change. - add 10% to conversion wait time as it seems it is sometimes a little small. * ade7753 - replace use of core mlock with a local lock. This is part of a long term effort to make the use of mlock opaque and single purpose. * ade7759 - expand the use of buf_lock to cover previous mlock cases. This is a slightly nicer solution to the same issue as in ade7753. * cros_ec - drop an unused variable * inv_mpu6050 - add a missing break in a switch for consistency - not actual bug, - make some local arrays static to save on object code size. * max5481 - drop manual setting of the spi module owner as handled by the spi core. * max5487 - drop manual setting of the spi module owner as handled by the spi core. * max9611 - drop explicit setting of the i2c module owner as handled by the i2c core. * mcp320x - speed up reads on single channel devices, - drop unused of_device_id data elements, - document the struct mcp320x, - improve binding docs to reflect restrictions on spi setup and to make it explicit that the reference regulator is needed. * mma8452 - symbolic to octal permissions, - unsigned to unsigned int. * st_lsm6dsx - avoid setting odr values multiple times, - drop config of LIR as it is only ever set to the existing defaults, - drop rounding configuration as it only ever matches the defaults. * ti-ads8688 - drop manual setting of the spi module owner as handled by the spi core. * tsl2x7x - constify the i2c_device_id, - cleanup limit checks to avoid static checker warnings (and generally have nicer code).
| | * | iio:magnetometer: drop assign iio_info.driver_module and iio_trigger_ops.ownerJonathan Cameron2017-08-228-10/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The equivalent of both of these are now done via macro magic when the relevant register calls are made. The actual structure elements will shortly go away. Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
* | | | License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-022-0/+2
| |_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | Merge tag 'iio-fixes-for-4.14a' of ↵Greg Kroah-Hartman2017-09-251-0/+4
|\ \ \ | |/ / |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: First round of IIO fixes for the 4.14 cycle Note this includes fixes from recent merge window. As such the tree is based on top of a prior staging/staging-next tree. * iio core - return and error for a failed read_reg debugfs call rather than eating the error. * ad7192 - Use the dedicated reset function in the ad_sigma_delta library instead of an spi transfer with the data on the stack which could cause problems with DMA. * ad7793 - Implement a dedicate reset function in the ad_sigma_delta library and use it to correctly reset this part. * bme280 - ctrl_reg write must occur after any register writes for updates to take effect. * mcp320x - negative voltage readout was broken. - Fix an oops on module unload due to spi_set_drvdata not being called in probe. * st_magn - Fix the data ready line configuration for the lis3mdl. It is not configurable so the st_magn core was assuming it didn't exist and so wasn't consuming interrupts resulting in an unhandled interrupt. * stm32-adc - off by one error on max channels checking. * stm32-timer - preset should not be buffered - reorganising register writes avoids this. - fix a corner case in which write preset goes wrong when a timer is used first as a trigger then as a counter with preset. Odd case but you never know. * ti-ads1015 - Fix setting of comparator polarity by fixing bitfield definition. * twl4030 - Error path handling fix to cleanup in event of regulator registration failure. - Disable the vusb3v1 regulator correctly in error handling - Don't paper over a regulator enable failure.
| * | iio: magnetometer: st_magn: fix drdy line configuration for LIS3MDLLorenzo Bianconi2017-09-031-0/+4
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Data-ready line in LIS3MDL is routed to drdy pin and it is not possible to select a different INT pin. st_sensors_set_dataready_irq() assumes that if drdy int address is not exported in register map, irq trigger is not supported by the sensor and hw_irq_trigger is always false. Based on this configuration st_sensors_irq_thread does not consume generated interrupt causing an unhandled irq. Fix this taking into account status register address in st_sensors_set_dataready_irq() Fixes: 90efe0556292 (iio: st_sensors: harden interrupt handling) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* | Merge 4.13-rc7 into staging-nextGreg Kroah-Hartman2017-08-281-3/+1
|\ \ | |/ |/| | | | | | | We want the staging and iio fixes in here to handle the merge issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * iio: magnetometer: st_magn: remove ihl property for LSM303AGRLorenzo Bianconi2017-08-201-2/+0
| | | | | | | | | | | | | | | | | | | | | | Remove IRQ active low support for LSM303AGR since the sensor does not support that capability for data-ready line Fixes: a9fd053b56c6 (iio: st_sensors: support active-low interrupts) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
| * iio: magnetometer: st_magn: fix status register address for LSM303AGRLorenzo Bianconi2017-08-201-1/+1
| | | | | | | | | | | | | | | | Fixes: 97865fe41322 (iio: st_sensors: verify interrupt event to status) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* | iio: magnetometer: ak8974: debug AMI306 calibration dataMichał Mirosław2017-08-201-0/+41
| | | | | | | | | | | | | | | | Use AMI306 calibration data for randomness and debugging. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* | iio: magnetometer: ak8974: mark INT_CLEAR as preciousMichał Mirosław2017-08-201-0/+6
| | | | | | | | | | | | | | | | Reading INT_CLEAR has side effects - disallow reading it via debugfs. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* | iio: magnetometer: ak8974: add_device_randomness (serial number)Michał Mirosław2017-08-201-0/+2
| | | | | | | | | | | | | | | | Mix device-specific data into randomness pool. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* | iio: magnetometer: ak8974: support AMI306 variantMichał Mirosław2017-08-202-22/+72
| | | | | | | | | | | | | | | | Add support for AMI306 magnetometer - very similar to AMI305. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* | iio: magnetometer: add support to LIS2MDLLorenzo Bianconi2017-08-174-0/+12
| | | | | | | | | | | | | | | | | | | | add support to STMicroelectronics LIS2MDL magnetometer in st_magn framework http://www.st.com/resource/en/datasheet/lis2mdl.pdf Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* | iio: magnetometer: st_magn_spi: add OF capability to st_magn_spiLorenzo Bianconi2017-07-021-0/+25
| | | | | | | | | | | | | | | | Add device tree support for LIS3MDL and LSM303AGR magnetometer sensors Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* | iio: magnetometer: Only declare ACPI table when ACPI is enableMatthias Kaehlcke2017-07-021-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Don't inflate the kernel size with data that isn't used. The conditional declaration also fixes the following warning when building with clang: drivers/iio/magnetometer/ak8975.c:704:36: error: variable 'ak_acpi_match' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration] Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* | iio: common: st_sensors: move st_sensors_of_i2c_probe() in common codeLorenzo Bianconi2017-07-011-1/+2
| | | | | | | | | | | | | | | | | | | | | | Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in st_sensors_of_name_probe(). That change is necessary to add device-tree support in spi code otherwise the rest of the autodetection will fail since spi->modalias (and indio_dev->name) will be set using compatible string value that differs from standard sensor name Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* | iio: magnetometer: st_magn_core: enable multiread by default for LIS3MDLLorenzo Bianconi2017-07-011-1/+1
|/ | | | | | | | | | | | Enable multiread by default for LIS3MDL since using I2C interface the subaddr Msb is used to automatically increase the slave address during multiple data read/write. In the same way, using SPI interface, bit 1 in register address is used to enable auto-increment of the slave address in multiple read/write. Fixes: 872e79add756 (iio:magn: Add STMicroelectronics magn driver) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magnetometer: st_magn_spi: fix spi_device_id tableLorenzo Bianconi2017-06-111-2/+0
| | | | | | | | | Remove LSM303DLHC, LSM303DLM from st_magn_id_table since LSM303DL series does not support spi interface Fixes: 872e79add756 (iio: magn: Add STMicroelectronics magn driver) Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* Merge 4.11-rc4 into staging-nextGreg Kroah-Hartman2017-03-271-2/+2
|\ | | | | | | | | | | We need the IIO fixes in here as well to handle merge issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * iio: magnetometer: ak8974: remove incorrect __exit markupsDmitry Torokhov2017-03-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Even if bus is not hot-pluggable, devices can be unbound from the driver via sysfs, so we should not be using __exit annotations on remove() methods. The only exception is drivers registered with platform_driver_probe() which specifically disables sysfs bind/unbind attributes. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* | iio: magnetometer: mag3110: Add OF device ID tableJavier Martinez Canillas2017-03-191-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | The driver doesn't have a struct of_device_id table but supported devices are registered via Device Trees. This is working on the assumption that a I2C device registered via OF will always match a legacy I2C device ID and that the MODALIAS reported will always be of the form i2c:<device>. But this could change in the future so the correct approach is to have an OF device ID table if the devices are registered via OF. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* | iio: magnetometer: bmc150_magn_i2c: Add OF device ID tableJavier Martinez Canillas2017-03-191-0/+9
|/ | | | | | | | | | | | | The driver doesn't have a struct of_device_id table but supported devices are registered via Device Trees. This is working on the assumption that a I2C device registered via OF will always match a legacy I2C device ID and that the MODALIAS reported will always be of the form i2c:<device>. But this could change in the future so the correct approach is to have an OF device ID table if the devices are registered via OF. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magnetometer: mag3110: claim direct mode during raw writesAlison Schofield2017-01-211-10/+20
| | | | | | | | | | Driver was checking for direct mode but not locking it. Use claim/release helper functions to guarantee the device stays in direct mode during raw writes. Signed-off-by: Alison Schofield <amsfield22@gmail.com> Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magnetometer: ak8974: remove redundant zero timeout checkColin Ian King2017-01-141-6/+2
| | | | | | | | | | | | | At the end of the delay loop timeout will always be zero and hence the check for !timeout will always be true. Remove the redundant check and the redundant return 0 at the end of the function. Fixes CoverityScan CID#1357168 ("Logically dead code") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magnetometer: separate the values of attributes based on their usage ↵Ooi, Joyce2016-11-241-35/+112
| | | | | | | | | | | | | | | | | | | | | | | | type for HID compass sensor There are 2 usage types (Magnetic Flux and Heading data field) for HID compass sensor, thus the values of offset, scale, and sensitivity should be separated according to their respective usage type. The changes made are as below: 1. Hysteresis: A struct hid_sensor_common rot_attributes is created in struct magn_3d_state to contain the sensitivity for IIO_ROT. 2. Scale: scale_pre_decml and scale_post_decml are separated for IIO_MAGN and IIO_ROT. 3. Offset: Same as scale, value_offset is separated for IIO_MAGN and IIO_ROT. For sensitivity, HID_USAGE_SENSOR_ORIENT_MAGN_FLUX and HID_USAGE_SENSOR_ORIENT_MAGN_HEADING are used for sensivitity fields based on the HID Sensor Usages specifications. Hence, these changes are added on the sensitivity field. Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: st_magn: inline per-sensor dataLinus Walleij2016-11-121-251/+125
| | | | | | | | | | | | | | | | | | | | | | | | | We have #defines for all the individual sensor registers and value/mask pairs #defined at the top of the file and used at exactly one spot. This is usually good if the #defines give a meaning to the opaque magic numbers. However in this case, the semantic meaning is inherent in the name of the C99-addressable fields, and that means duplication of information, and only makes the code hard to maintain since you every time have to add a new #define AND update the site where it is to be used. Get rid of the #defines and just open code the values into the appropriate struct elements. Make sure to explicitly address the .hz and .value fields in the st_sensor_odr_avl struct so that the meaning of all values is clear. This patch is purely syntactic should have no semantic effect. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magnetometer: ak8974: small endianness fixesIco Doornekamp2016-10-031-4/+4
| | | | | | | Fixes two cases of 'cast to restricted __le16' as reported by sparse. Signed-off-by: Ico Doornekamp <ico@pruts.nl> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* drivers: iio: magnetometer: Fix sparse endianness warnings cast to ↵Sandhya Bankar2016-09-271-7/+9
| | | | | | | | | | | | | | restricted __be16 Fix the following sparse endianness warnings: drivers/iio/magnetometer/ak8975.c:716:16: warning: cast to restricted __le16 drivers/iio/magnetometer/ak8975.c:837:19: warning: cast to restricted __le16 drivers/iio/magnetometer/ak8975.c:838:19: warning: cast to restricted __le16 drivers/iio/magnetometer/ak8975.c:839:19: warning: cast to restricted __le16 Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: ak8974: remove .owner field for driverWei Yongjun2016-08-291-1/+0
| | | | | | | | | | Remove .owner field if calls are used which set it automatically. Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn/ak8974: avoid unused function warningArnd Bergmann2016-08-291-4/+2
| | | | | | | | | | | | | | | The ak8974_configure() function is used only from the PM code, but that can be hidden when CONFIG_PM is disabled: drivers/iio/magnetometer/ak8974.c:201:12: error: 'ak8974_configure' defined but not used [-Werror=unused-function] This replaces the #ifdef with a __maybe_unused annotation, which will work correctly in all configurations and avoid the warning, as the compiler can now see where ak8974_configure is called from. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 7c94a8b2ee8c ("iio: magn: add a driver for AK8974") Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magnetometer: mag3110: claim direct mode during raw readsAlison Schofield2016-08-211-8/+15
| | | | | | | | | | Driver was checking for direct mode but not locking it. Use claim/release helper functions to guarantee the device stays in direct mode during raw reads. Signed-off-by: Alison Schofield <amsfield22@gmail.com> Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: add a driver for AK8974Linus Walleij2016-08-153-1/+879
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a driver for the Asahi Kasei AK8974 and its sibling AMI305 magnetometers. It was deployed on scale in 2009 on a multitude of devices. It is distincly different from AK8973 and AK8975 and needs its own driver. This patch is based on the long lost work of Samu Onkalo at Nokia, who made a misc character device driver for the Maemo/MeeGo Nokia devices, before the time of the IIO subsystem. It was mounted in e.g. the Nokia N950, N8, N86, N97 etc. It is also mounted on the ST-Ericsson HREF reference designs. It works nicely in sysfs: $ cat in_magn_x_raw && cat in_magn_y_raw && cat in_magn_z_raw -55 -101 161 And with buffered reads using a simple HRTimer trigger: $ generic_buffer -c10 -a -n ak8974 -t foo iio device number being used is 3 iio trigger number being used is 2 No channels are enabled, enabling all channels Enabling: in_magn_x_en Enabling: in_magn_y_en Enabling: in_magn_z_en Enabling: in_timestamp_en /sys/bus/iio/devices/iio:device3 foo -58.000000 -102.000000 157.000000 946684970985321044 -60.000000 -98.000000 159.000000 946684971012237548 -60.000000 -106.000000 163.000000 946684971032257080 -62.000000 -94.000000 169.000000 946684971052185058 -58.000000 -98.000000 163.000000 946684971072204589 -54.000000 -100.000000 163.000000 946684971092224121 -53.000000 -103.000000 164.000000 946684971112731933 -50.000000 -102.000000 165.000000 946684971132232666 -61.000000 -101.000000 164.000000 946684971152191162 -57.000000 -99.000000 168.000000 946684971172210693 Disabling: in_magn_x_en Disabling: in_magn_y_en Disabling: in_magn_z_en Disabling: in_timestamp_en I cannot currently scale these raw values to gauss. This is because of lack of documentation. I have sent a request for a datasheet to Asahi Kasei. The driver can optionally use a DRDY line IRQ to capture data, else it will sleep and poll. Cc: Samu Onkalo <samu.onkalo@intel.com> Cc: Sebastian Reichel <sre@kernel.org> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Tested-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: ak8975: deploy runtime and system PMLinus Walleij2016-06-301-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds runtime PM support to the AK8975 driver. It solves two problems: - After reading the first value the chip was left in MODE_ONCE, meaning (presumably) it may be consuming more power. Now the runtime PM hooks kick in and set it to POWER_DOWN. - Regulators were simply enabled and left on, making it impossible to turn the power consuming regulators off because of the increased refcount. We now disable the regulators at autosuspend. - We also handle system suspend: by using pm_runtime_force_suspend() and pm_runtime_force_resume() from the system PM sleep hooks, the runtime PM code is managing the power also for this case. It is currently not completely optimal: when the system resumes the AK8975 goes into active mode even if noone is going to use it: currently the force calls need to be paired, but the runtime PM people are working on making it possible to leave devices runtime suspended when coming back from sleep. Inspired by my work on the BH1780 light sensor driver. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: ak8975: make sure to power down at remove()Linus Walleij2016-06-301-0/+1
| | | | | | | | | | The code was not powering the magnetometer down properly at remove(): just cutting the regulators without first setting the device in power off mode. Fix this. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: ak8975: allow a delay after enabling regulatorsLinus Walleij2016-06-301-0/+6
| | | | | | | | The datasheet actually specifies that we need to wait atleast 500us after powering on the device before trying to set mode. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: ak8975: refactor regulator handlersLinus Walleij2016-06-301-25/+18
| | | | | | | | | Move the regulator_get() calls directly into the probe() function, keep only the power_on()/power_off() functions to flick the regulators on/off. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: ak8975: add Vid regulatorLinus Walleij2016-06-301-0/+15
| | | | | | | | | | | | | | | The AK8975 has two power sources: Vdd (analog voltage supply) and Vid (digital voltage supply). Optionally also obtain the Vid supply regulator and enable it. If an error occurs when enabling one of the regulators: bail out. Cc: Gregor Boirie <gregor.boirie@parrot.com> Cc: Richard Leitner <dev@g0hl1n.net> Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio: magn: ak8975: fix regulator usageLinus Walleij2016-06-301-9/+7
| | | | | | | | | | | | | | | | | | | | | | IS_ERR_OR_NULL() should never be used with regulators because a NULL pointer may be a perfectly valid dummy regulator We should always succeed to fetch and enable a regulator, but it may be a dummy. That is fine, so bail out for any real errors or probe deferrals Include the error code in the warning print so we know what kind of problem we're dealing with (for example it is nice to see if it is a probe deferral). As we will bail out of probe if the regulator is erroneous, just issue regulator_disable() on the poweroff path: it will succeed. Cc: Mark Brown <broonie@kernel.org> Cc: Lars-Peter Clausen Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* iio:core: timestamping clock selection supportGregor Boirie2016-06-303-3/+4
| | | | | | | | | | | | | | | Adds a new per-device sysfs attribute "current_timestamp_clock" to allow userspace to select a particular POSIX clock for buffered samples and events timestamping. Following clocks, as listed in clock_gettime(2), are supported: CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW, CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and CLOCK_TAI. Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com> Acked-by: Sanchayan Maity <maitysanchayan@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* Merge 4.7-rc4 into staging-nextGreg Kroah-Hartman2016-06-202-1/+2
|\ | | | | | | | | | | | | We want the fixes in here, and we can resolve a merge issue in drivers/iio/industrialio-trigger.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * Merge tag 'iio-fixes-for-4.7a' of ↵Greg Kroah-Hartman2016-06-072-1/+2
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: First round of iio fixes for the 4.7 cycle. A slightly bumper set due to travel delaying the pull request and a fair few issues with the recent merge window patches. Patches all over the place. The st-sensors one is probably the most involved, but definitly solves the issues seen. Note there are some other issues around that handler (and the fact that a lot of boards tie a level interrupt chip to an edge interrupt only irq chip). These are not regressions however, so will turn up the slow route. * core - iio_trigger_attach_pollfunc had some really badly wrong error handling. Another nasty triggered whilst chasing down issues with the st sensors rework below. * ad5592r - fix an off by one error when allocating channels. * am2315 - a stray mutex unlock before we ever take the lock. * apds9960 - missing a parent in the driver model (which should be the i2c device). Result is it doesn't turn up under /sys/bus/i2c/devices which some userspace code uses for repeatable device identification. * as3935 - ABI usage bug which meant a processed value was reported as raw. Now reporting scale as well to ensure userspace has the info it needs. - Don't return processed value via the buffer - it doesn't conform to the ABI and will overflow in some cases. - Fix a wrongly sized buffer which would overflow trashing part of the stack. Also move it onto the heap as part of the fix. * bh1780 - a missing return after write in debugfs lead to an incorrect read and a null pointer dereference. - dereferencing the wrong pointer in suspend and resume leading to unpredictable results. - assign a static name to avoid accidentally ending up with no name if loaded via device tree. * bmi160 - output data rate for the accelerometer was incorrectly reported. Fix it. - writing the output data rate was also wrong due to reverse parameters. * bmp280 - error message for wrong chip ID gave the wrong expected value. * hdc100x - mask for writing the integration time was wrong allowin g us to get 'stuck' in a particular value with no way back. - temperature reported in celsius rather than millicelsius as per the ABI. - Get rid of some incorrect data shifting which lead to readings being rather incorrect. * max44000 - drop scale attribute for proximity as it is an unscaled value (depends on what is in range rather than anything knowable at the detector). * st-pressure - ABI compliance fixes - units were wrong. * st-sensors - We introduced some nasty issues with the recent switch over to a a somewhat threaded handler in that we broke using a software trigger with these devices. Now do it properly. It's a larger patch than ideal for a fix, but the logic is straight forward. - Make sure the trigger is initialized before requesting the interrupt. This matters now the interrupt can be shared. Before it was ugly and wrong but short of flakey hardware could not be triggered. - Hammer down the dataready pin at boot - otherwise with really unlucky timing things could get interestingly wedged requiring a hard power down of the chip.
| | * iio: st_sensors: switch to a threaded interruptLinus Walleij2016-05-292-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded ("iio: st_sensors: verify interrupt event to status") caused a regression when reading ST sensors from a HRTimer trigger rather than the intrinsic interrupts: the HRTimer may trigger faster than the sensor provides new values, and as the check against new values available as a cause of the interrupt trigger was done in the poll function, this would bail out of the HRTimer interrupt with IRQ_NONE. So clearly we need to only check the new values available from the proper interrupt handler and not from the poll function, which should rather just read the raw values from the registers, put them into the buffer and be happy. To achieve this: switch the ST Sensors over to using a true threaded interrupt handler. In the interrupt thread, check if new values are available, else yield to the (potential) next device on the same interrupt line to check the registers. If the interrupt was ours, proceed to poll the values. Instead of relying on iio_trigger_generic_data_rdy_poll() as a top half to wake up the thread that polls the sensor for new data, have the thread call iio_trigger_poll_chained() after determining that is is the proper source of the interrupt. This is modelled on drivers/iio/accel/mma8452.c which is already using a properly threaded interrupt handler. In order to get the same precision in timestamps as previously, where samples would be timestamped in the poll function pf->timestamp when calling iio_trigger_generic_data_rdy_poll() we introduce a local timestamp in the sensor data, set it in the top half (fastpath) of the interrupt handler and provide that to the core when calling iio_push_to_buffers_with_timestamp(). Additionally: if the active scanmask is not set for the sensor no IRQs should be enabled and we need to bail out with IRQ_NONE. This can happen if spurious IRQs fire when installing the threaded interrupt handler. Tested with hard interrupt triggers on LIS331DL, then also tested with hrtimers on the same sensor by creating a 75Hz HRTimer and using it to poll the sensor. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Giuseppe Barba <giuseppe.barba@st.com> Cc: Denis Ciocca <denis.ciocca@st.com> Reported-by: Crestez Dan Leonard <cdleonard@gmail.com> Tested-by: Crestez Dan Leonard <cdleonard@gmail.com> Tested-by: Jonathan Cameron <jic23@kernel.org> Fixes: 97865fe41322 ("iio: st_sensors: verify interrupt event to status") Signed-off-by: Jonathan Cameron <jic23@kernel.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 19:27:07 +0000