| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The device's hardware reset pin is only required if the platform
must be able to update the device's firmware.
As such, demote the reset GPIO to optional in support of devices
that ship with pre-programmed firmware and don't route the reset
pin back to the SoC.
In that case, the 'fw_file' attribute is hidden because there is
no way to open the bootloader. The logic is extended to the case
in which the device does not advertise bootloader support in the
first place.
Last but not least, remove the hardware reset performed at probe
because there is no reason to reset the device manually. A power
on reset function already ensures a clean reset at start-up.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210323021006.367-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The bootloader can be closed using the 'execute' command (0x02) or
hardware reset. Rather than using the former option for successful
firmware update procedures and reserving the latter for recovering
the device upon failure, simply use hardware reset for all cases.
The post-bootloader initialization delay increases marginally when
triggered by a hardware reset, so increase the wait time to ensure
the device does not subsequently fail to respond.
As part of this change, refactor the return path to avoid an extra
assignment and to make the logic a bit smaller.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-6-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The vendor-assigned firmware project number is restricted to the
generic project number (15); however the vendor may assign other
project numbers to specific applications and customers.
These custom project numbers may be based on forwards-compatible
firmware revision 1.x. However, the driver unnecessarily rejects
anything older than firmware revision 2.0.
To support other applications, remove these unnecessarily strict
checks and enter the bootloader only for truly incompatible A000
devices.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-5-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add the read-only 'fw_info' attribute which reports information
about the device's firmware in the following format:
a.b.c.d:e.f
Where:
a = Product number (e.g. 40 for IQS550)
b = Project number (e.g. 15)
c = Firmware revision (major)
d = Firmware revision (minor)
e = Customer-assigned exported file version (major)
f = Customer-assigned exported file version (minor)
As part of the corresponding rework to uses of 'bl_status', the
IQS5XX_BL_STATUS_RESET definition is dropped with 0 used in its
place instead.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-4-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Set the maximum ABS_MT_PRESSURE value and use the existing U16_MAX
definition instead of a magic number to validate ABS_MT_POSITION_X
and ABS_MT_POSITION_Y.
Also use input_set_abs_params() rather than input_abs_set_max() to
avoid having to call input_set_capability() separately.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-3-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
| |
Replace 'http' with 'https' and correct the spelling of the nearby
word 'datasheet'.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-2-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
If execution jumps to the err_kfree label, error_bl is evaluated
before it is initialized. Fix this by initializing it to zero.
Fixes: 2539da6677b6 ("Input: iqs5xx - preserve bootloader errors")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611592500-32209-1-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Avoid placing the device in suspend mode (from which it cannot
generate interrupts) if it is defined as a wake-up source. The
device is still permitted to enter a low-power sensing mode on
its own.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-11-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After the device is initialized, it runs ATI (calibration) during
which it cannot readily respond to I2C communication. To keep the
open and close callbacks from writing to the device too soon, the
driver waits 100 ms before returning from probe.
The vendor reports that ATI may actually take up to 250 ms to run
(including margin), so increase the delay accordingly. Update the
comments to clarify the reason for the delay as well.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-9-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Instead of relying on firmware to enable important register fields
and performing read-modify-write operations to additionally enable
the fields the driver cares about, it's much simpler just to write
all of the pertinent fields explicitly.
This avoids an unnecessary register read operation at start-up and
makes way for the iqs5xx_read_byte() helper to be dropped.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-8-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The present implementation manipulates axis swap and inversion fields
in the device to more or less duplicate what touchscreen_report_pos()
does. The resulting logic is convoluted and difficult to follow.
Instead report the maximum X and Y coordinates in earnest as they are
read from the device, then let touchscreen_parse_properties() fix the
axes up as necessary. Finally, use touchscreen_report_pos() to report
the transformed coordinates.
Last but not least, the maximum X and Y coordinates are not functions
of the number of rows/columns that comprise the touch surface. Either
coordinate is simply limited to 1 below what is reported for absolute
X or Y coordinates when no fingers are present (0xFFFF).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-7-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The device may be inadvertently reset during runtime in the event
of ESD strike, etc. To protect against this case, acknowledge the
SHOW_RESET interrupt and re-initialize the device.
To facilitate this change, expand the range of registers that are
read in the interrupt handler to include the system status fields.
Also, update the unrelated (but nearby) SUSPEND register field to
use the BIT() macro. The remaining register fields are cleaned up
in another patch.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-6-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The bootloader NAK's all I2C communication after the first 64-byte
bulk write if the bus frequency is equal to 400 kHz. This prevents
the platform from pushing updated firmware to the device.
The vendor's USB bootloader programming dongle appears to insert a
delay between the "open" command and the first 64-byte bulk write.
Adding a similar delay to the driver seems to eliminate the issue.
Furthermore, the dongle does not access the bootloader immediately
after powering up the device. Follow suit by adding a delay before
the "open" command to avoid wasted retries at 400 kHz.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-4-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After user space writes the fw_file attribute to push new firmware
to the device, the driver calls iqs5xx_dev_init() to re-initialize
the device with the updated firmware or recover the device in case
the update failed.
In the case of the latter, however, iqs5xx_fw_file_write() returns
zero (success) so long as iqs5xx_dev_init() does not fail, and any
error encountered during the update process is lost. Solve this by
saving the error before calling iqs5xx_dev_init().
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-3-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Copyrights are generally followed by the name of a person or a
company (i.e. the copyright holder) but that was not done here.
Fix this by squashing the 'copyright' and 'author' lines.
Also, trim some leading whitespace ahead of the parameters for
the fw_file_store() function and re-align them for readability.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-2-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
| |
Use the newly added helper in relevant input drivers.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/20200608112211.12125-3-andrzej.p@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200707180857.GA30600@embeddedor
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |\
| |
| |
| | |
Sync up with mainline to resolve conflicts in iforce driver.
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Calling input_mt_init_slots() copies ABS_MT_POSITION_X to ABS_X and
so on, but doing so before calling touchscreen_parse_properties()
leaves ABS_X min = max = 0 which may prompt an X server to ignore
the device.
To solve this problem, wait to call input_mt_init_slots() until all
absolute axis information has been resolved (whether that's through
device tree via touchscreen_parse_properties() or from reading from
the device directly).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |/
|
|
|
|
|
|
| |
Calling i2c_set_clientdata() is enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
|
This patch adds support for the Azoteq IQS550/572/525 family of
trackpad/touchscreen controllers.
The driver has been tested with an IQS550EV02 evaluation board. A
demonstration of the driver's capabilities is available here:
https://youtu.be/sRNNx4XZBts
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
