summaryrefslogtreecommitdiffstats
path: root/drivers/mtd/nand/raw/gpmi-nand
Commit message (Collapse)AuthorAgeFilesLines
* mtd: rawnand: gpmi: Set WAIT_FOR_READY timeout based on program/erase timesSascha Hauer2022-07-151-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 06781a5026350 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong though: It is calculated based on the maximum page read time, but the timeout is also used for page write and block erase operations which require orders of magnitude bigger timeouts. Fix this by calculating busy_timeout_cycles from the maximum of tBERS_max and tPROG_max. This is for now the easiest and most obvious way to fix the driver. There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us the desired timeout for the current operation, so we could program the timeout dynamically for each operation instead of setting a fixed timeout. Also we could wire up the interrupt handler to actually detect and forward timeouts occurred when waiting for the chip being ready. As a sidenote I verified that the change in 06781a5026350 is really correct. I wired up the interrupt handler in my tree and measured the time between starting the operation and the timeout interrupt handler coming in. The time increases 41us with each step in the timeout register which corresponds to 4096 clock cycles with the 99MHz clock that I have. Fixes: 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy timeout setting") Fixes: b1206122069aa ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation") Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Han Xu <han.xu@nxp.com> Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com> Signed-off-by: Richard Weinberger <richard@nod.at>
* mtd: rawnand: gpmi: Fix setting busy timeout settingSascha Hauer2022-06-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as: | Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY | mode. This value is the number of GPMI_CLK cycles multiplied by 4096. So instead of multiplying the value in cycles with 4096, we have to divide it by that value. Use DIV_ROUND_UP to make sure we are on the safe side, especially when the calculated value in cycles is smaller than 4096 as typically the case. This bug likely never triggered because any timeout != 0 usually will do. In my case the busy timeout in cycles was originally calculated as 2408, which multiplied with 4096 is 0x968000. The lower 16 bits were taken for the 16 bit wide register field, so the register value was 0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings setting") however the value in cycles became 2384, which multiplied with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an intermediate timeout when reading from NAND. Fixes: b1206122069aa ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation") Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
* mtd: rawnand: gpmi: Add large oob bch setting supportHan Xu2022-04-212-5/+197
| | | | | | | | | | | | | | | | | | | | The code change proposes a new way to set bch geometry for large oob NAND (oobsize > 1KB). In this case, previous implementation can NOT guarantee the bad block mark always locates in data chunk, so we need a new way to do it. The general idea is, 1.Try all ECC strength from the maximum ecc that controller can support to minimum value required by NAND chip, any ECC strength makes the BBM locate in data chunk can be eligible. 2.If none of them works, using separate ECC for meta, which will add one extra ecc with the same ECC strength as other data chunks. This extra ECC can guarantee BBM located in data chunk, also we need to check if oob can afford it. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-6-han.xu@nxp.com
* mtd: rawnand: gpmi: Rename the variable ecc_chunk_sizeHan Xu2022-04-212-27/+34
| | | | | | | | | | | | | | There is only one variable ecc_chunk_size in bch_geometry data structure but two different field in BCH registers. The data0_size in BCH_FLASH0LAYOUT0 and datan_size in BCH_FLASH0LAYOUT1 should have dedicate variable since they might set to different values in some cases. For instance, if need dedicate ecc for meta area, the data0_size should be 0 rather than datan_size, but for all other cases, data0_size still equals to datan_size and it won't bring any function change. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-5-han.xu@nxp.com
* mtd: rawnand: gpmi: Uninline the gpmi_check_ecc functionHan Xu2022-04-211-1/+1
| | | | | | | | | The gpmi_check_ecc() is not small after adding more strict ecc check, uninline it. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-4-han.xu@nxp.com
* mtd: rawnand: gpmi: Add strict ecc strength checkHan Xu2022-04-211-1/+14
| | | | | | | | | Add nand_ecc_is_strong_enough() check in gpmi_check_ecc() function to make sure ecc strength can meet chip requirement. Signed-off-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-3-han.xu@nxp.com
* mtd: rawnand: gpmi: Refactor bch geometry settings functionHan Xu2022-04-211-12/+20
| | | | | | | | | | | | | | | | | | | | | | | | The code change refactor the bch geometry setting function, which doesn't change the default behavior, while user may choose to use chips required minimum ecc strength by DT flag "fsl,use-minimum-ecc". The default way to set bch geometry need to set the data chunk size(step_size) larger than oob size to make sure BBM locates in data chunk, then set the maximum ecc strength oob can hold. It always use unbalanced ECC layout, which ecc0 will cover both meta and data0 chunk. But the default bch setting is deprecated for large oobsize NAND (oobsize >1KB), so in the patch set, there is a split commit that introduces a new way to set bch geometry for large oob size NAND. For all other cases,set the bch geometry by chip required strength and step size, which uses the minimum ecc strength chip required. It can be explicitly enabled by DT flag "fsl,use-minimum-ecc", but need to be en/disabled in both u-boot and kernel at the same time. Signed-off-by: Han Xu <han.xu@nxp.com> Tested-by: Sean Nyekjaer <sean@geanix.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-2-han.xu@nxp.com
* Merge tag 'nand/for-5.18' into mtd/nextMiquel Raynal2022-03-231-5/+22
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Raw NAND core changes: * Rework of_get_nand_bus_width() * Remove of_get_nand_on_flash_bbt() wrapper * Protect access to rawnand devices while in suspend * bindings: Document the wp-gpios property Rax NAND controller driver changes: * atmel: Fix refcount issue in atmel_nand_controller_init * nandsim: - Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern - Merge repeat codes in ns_switch_state - Replace overflow check with kzalloc to single kcalloc * rockchip: Fix platform_get_irq.cocci warning * stm32_fmc2: Add NAND Write Protect support * pl353: Set the nand chip node as the flash node * brcmnand: Fix sparse warnings in bcma_nand * omap_elm: Remove redundant variable 'errors' * gpmi: - Support fast edo timings for mx28 - Validate controller clock rate - Fix controller timings setting * brcmnand: - Add BCMA shim - BCMA controller uses command shift of 0 - Allow platform data instantation - Add platform data structure for BCMA - Allow working without interrupts - Move OF operations out of brcmnand_init_cs() - Avoid pdev in brcmnand_init_cs() - Allow SoC to provide I/O operations - Assign soc as early as possible Onenand changes: * Check for error irq Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
| * mtd: rawnand: gpmi: support fast edo timings for mx28Dario Binacchi2022-01-231-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the i.MX28 manual (MCIMX28RM, Rev. 1, 2010) you can find an example (15.2.4 High-Speed NAND Timing) of how to configure the GPMI controller to manage High-Speed ​​NAND devices, so it was wrong to assume that only i.MX6 can achieve EDO timings. This patch has been tested on a 2048/64 byte NAND (Micron MT29F2G08ABAEAH4). Kernel mtd tests: - mtd_nandbiterrs - mtd_nandecctest - mtd_oobtest - mtd_pagetest - mtd_readtest - mtd_speedtest - mtd_stresstest - mtd_subpagetest - mtd_torturetest [cycles_count = 10000000] run without errors. Before this patch (mode 0): --------------------------- eraseblock write speed is 2098 KiB/s eraseblock read speed is 2680 KiB/s page write speed is 1689 KiB/s page read speed is 2522 KiB/s 2 page write speed is 1899 KiB/s 2 page read speed is 2579 KiB/s erase speed is 128000 KiB/s 2x multi-block erase speed is 73142 KiB/s 4x multi-block erase speed is 204800 KiB/s 8x multi-block erase speed is 256000 KiB/s 16x multi-block erase speed is 256000 KiB/s 32x multi-block erase speed is 256000 KiB/s 64x multi-block erase speed is 256000 KiB/s After this patch (mode 5): ------------------------- eraseblock write speed is 3390 KiB/s eraseblock read speed is 5688 KiB/s page write speed is 2680 KiB/s page read speed is 4876 KiB/s 2 page write speed is 2909 KiB/s 2 page read speed is 5224 KiB/s erase speed is 170666 KiB/s 2x multi-block erase speed is 204800 KiB/s 4x multi-block erase speed is 256000 KiB/s 8x multi-block erase speed is 256000 KiB/s 16x multi-block erase speed is 256000 KiB/s 32x multi-block erase speed is 256000 KiB/s 64x multi-block erase speed is 256000 KiB/s Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-5-dario.binacchi@amarulasolutions.com
| * mtd: rawnand: gpmi: validate controller clock rateDario Binacchi2022-01-231-4/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | What to do when the real rate of the gpmi clock is not equal to the required one? The solutions proposed in [1] did not lead to a conclusion on how to validate the clock rate, so, inspired by the document [2], I consider the rate correct only if not lower or equal to the rate of the previous edo mode. In fact, in chapter 4.16.2 (NV-DDR) of the document [2], it is written that "If the host selects timing mode n, then its clock period shall be faster than the clock period of timing mode n-1 and slower than or equal to the clock period of timing mode n.". I thought that it could therefore also be used in this case, without therefore having to define the valid rate ranges empirically. For example, suppose that gpmi_nfc_compute_timings() is called to set edo mode 5 (100MHz) but the rate returned by clk_round_rate() is 80MHz (edo mode 4). In this case gpmi_nfc_compute_timings() will return error, and will be called again to set edo mode 4, which this time will be successful. [1] https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org [2] http://www.onfi.org/-/media/client/onfi/specs/onfi_3_0_gold.pdf?la=en Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-4-dario.binacchi@amarulasolutions.com
| * mtd: rawnand: gpmi: fix controller timings settingDario Binacchi2022-01-231-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set the controller registers according to the real clock rate. The controller registers configuration (setup, hold, timeout, ... cycles) depends on the clock rate of the GPMI. Using the real rate instead of the ideal one, avoids that this inaccuracy (required_rate - real_rate) affects the registers setting. This patch has been tested on two custom boards with i.MX28 and i.MX6 SOCs: - i.MX28: required rate 100MHz, real rate 99.3MHz - i.MX6 required rate 100MHz, real rate 99MHz Fixes: b1206122069a ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation") Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-3-dario.binacchi@amarulasolutions.com
* | mtd: rawnand: gpmi: don't leak PM reference in error pathChristian Eggers2022-01-261-1/+2
|/ | | | | | | | | | | | If gpmi_nfc_apply_timings() fails, the PM runtime usage counter must be dropped. Reported-by: Pavel Machek <pavel@denx.de> Fixes: f53d4c109a66 ("mtd: rawnand: gpmi: Add ERR007117 protection for nfc_apply_timings") Signed-off-by: Christian Eggers <ceggers@arri.de> Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220125081619.6286-1-ceggers@arri.de
* mtd: rawnand: gpmi: Use platform_get_irq_byname() to get the interruptLad Prabhakar2021-12-221-7/+4
| | | | | | | | | | | | | | | platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypasses the hierarchical setup and messes up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq_byname(). Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-3-prabhakar.mahadev-lad.rj@bp.renesas.com
* mtd: rawnand: gpmi: remove unneeded variableMinghao Chi2021-12-171-4/+1
| | | | | | | | | Return status directly from function called. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211213112627.436745-1-chi.minghao@zte.com.cn
* mtd: rawnand: gpmi: Add ERR007117 protection for nfc_apply_timingsChristian Eggers2021-11-191-3/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | gpmi_io clock needs to be gated off when changing the parent/dividers of enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX). Otherwise this rate change can lead to an unresponsive GPMI core which results in DMA timeouts and failed driver probe: [ 4.072318] gpmi-nand 112000.gpmi-nand: DMA timeout, last DMA ... [ 4.370355] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -110 ... [ 4.375988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22 [ 4.381524] gpmi-nand 112000.gpmi-nand: Error in ECC-based read: -22 [ 4.387988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22 [ 4.393535] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22 ... Other than stated in i.MX 6 erratum ERR007117, it should be sufficient to gate only gpmi_io because all other bch/nand clocks are derived from different clock roots. The i.MX6 reference manuals state that changing clock muxers can cause glitches but are silent about changing dividers. But tests showed that these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn, the manual guarantees that no glitches can happen when changing dividers. Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de> Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Signed-off-by: Christian Eggers <ceggers@arri.de> Cc: stable@vger.kernel.org Acked-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de
* mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6Stefan Riedmueller2021-11-191-9/+0
| | | | | | | | | | | There is no need to explicitly set the default gpmi clock rate during boot for the i.MX 6 since this is done during nand_detect anyway. Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de> Cc: stable@vger.kernel.org Acked-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-1-ceggers@arri.de
* mtd: rawnand: gpmi: Make use of the helper function ↵Cai Huoqing2021-09-141-3/+1
| | | | | | | | | | | | devm_platform_ioremap_resource_byname() Use the devm_platform_ioremap_resource_byname() helper instead of calling platform_get_resource_byname() and devm_ioremap_resource() separately Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210901074130.9083-1-caihuoqing@baidu.com
* mtd: rawnand: Use more recent ONFI specification wordingMiquel Raynal2021-05-261-1/+1
| | | | | | | | | | In particular, first ONFI specifications referred to SDR modes as asynchronous modes, which is not the term we usually have in mind. The spec has then been updated, so do the same here in the NAND subsystem to avoid any possible confusion. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-7-miquel.raynal@bootlin.com
* mtd: rawnand: gpmi: Fix a double free in gpmi_nand_initLv Yunlong2021-04-071-1/+1
| | | | | | | | | | | | | | | | | | | | If the callee gpmi_alloc_dma_buffer() failed to alloc memory for this->raw_buffer, gpmi_free_dma_buffer() will be called to free this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL and valid ptr. Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer() is called again to free this->auxiliary_virt in err_out. This causes a double free. As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's error path, so it should return err directly instead of releasing the dma buffer again. Fixes: 4d02423e9afe6 ("mtd: nand: gpmi: Fix gpmi_nand_init() error path") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
* mtd: rawnand: gpmi: fix dst bit offset when extracting raw payloadSean Nyekjaer2021-01-041-1/+1
| | | | | | | | | | | | Re-add the multiply by 8 to "step * eccsize" to correct the destination bit offset when extracting the data payload in gpmi_ecc_read_page_raw(). Fixes: e5e5631cc889 ("mtd: rawnand: gpmi: Use nand_extract_bits()") Cc: stable@vger.kernel.org Reported-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Sean Nyekjaer <sean@geanix.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201221100013.2715675-1-sean@geanix.com
* mtd: rawnand: gpmi: Use a single line for of_device_idFabio Estevam2020-12-101-16/+6
| | | | | | | | | The .compatible and .data pairs can be stored in a single line, which makes the code more concise. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201208221243.3255-1-festevam@gmail.com
* mtd: rawnand: gpmi: Fix the random DMA timeout issueHan Xu2020-12-101-9/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To get better performance, current gpmi driver collected and chained all small DMA transfers in gpmi_nfc_exec_op, the whole chain triggered and wait for complete at the end. But some random DMA timeout found in this new driver, with the help of ftrace, we found the root cause is as follows: Take gpmi_ecc_read_page() as an example, gpmi_nfc_exec_op collected 6 DMA transfers and the DMA chain triggered at the end. It waits for bch completion and check jiffies if it's timeout. The typical function graph shown below, 63.216351 | 1) | gpmi_ecc_read_page() { 63.216352 | 1) 0.750 us | gpmi_bch_layout_std(); 63.216354 | 1) | gpmi_nfc_exec_op() { 63.216355 | 1) | gpmi_chain_command() { 63.216356 | 1) | mxs_dma_prep_slave_sg() { 63.216357 | 1) | /* mxs chan ccw idx: 0 */ 63.216358 | 1) 1.750 us | } 63.216359 | 1) | mxs_dma_prep_slave_sg() { 63.216360 | 1) | /* mxs chan ccw idx: 1 */ 63.216361 | 1) 2.000 us | } 63.216361 | 1) 6.500 us | } 63.216362 | 1) | gpmi_chain_command() { 63.216363 | 1) | mxs_dma_prep_slave_sg() { 63.216364 | 1) | /* mxs chan ccw idx: 2 */ 63.216365 | 1) 1.750 us | } 63.216366 | 1) | mxs_dma_prep_slave_sg() { 63.216367 | 1) | /* mxs chan ccw idx: 3 */ 63.216367 | 1) 1.750 us | } 63.216368 | 1) 5.875 us | } 63.216369 | 1) | /* gpmi_chain_wait_ready */ 63.216370 | 1) | mxs_dma_prep_slave_sg() { 63.216372 | 1) | /* mxs chan ccw idx: 4 */ 63.216373 | 1) 3.000 us | } 63.216374 | 1) | /* gpmi_chain_data_read */ 63.216376 | 1) | mxs_dma_prep_slave_sg() { 63.216377 | 1) | /* mxs chan ccw idx: 5 */ 63.216378 | 1) 2.000 us | } 63.216379 | 1) 1.125 us | mxs_dma_tx_submit(); 63.216381 | 1) 1.000 us | mxs_dma_enable_chan(); 63.216712 | 0) 2.625 us | mxs_dma_int_handler(); 63.216717 | 0) 4.250 us | bch_irq(); 63.216723 | 0) 1.250 us | mxs_dma_tasklet(); 63.216723 | 1) | /* jiffies left 250 */ 63.216725 | 1) ! 372.000 us | } 63.216726 | 1) 2.625 us | gpmi_count_bitflips(); 63.216730 | 1) ! 379.125 us | } but it's not gurantee that bch irq handled always after dma irq handled, sometimes bch_irq comes first and gpmi_nfc_exec_op won't wait anymore, another gpmi_nfc_exec_op may get invoked before last DMA chain IRQ handled, this messed up the next DMA chain and causes DMA timeout. Check the trace log when issue happened. 63.218923 | 1) | gpmi_ecc_read_page() { 63.218924 | 1) 0.625 us | gpmi_bch_layout_std(); 63.218926 | 1) | gpmi_nfc_exec_op() { 63.218927 | 1) | gpmi_chain_command() { 63.218928 | 1) | mxs_dma_prep_slave_sg() { 63.218929 | 1) | /* mxs chan ccw idx: 0 */ 63.218929 | 1) 1.625 us | } 63.218931 | 1) | mxs_dma_prep_slave_sg() { 63.218931 | 1) | /* mxs chan ccw idx: 1 */ 63.218932 | 1) 1.750 us | } 63.218933 | 1) 5.875 us | } 63.218934 | 1) | gpmi_chain_command() { 63.218934 | 1) | mxs_dma_prep_slave_sg() { 63.218935 | 1) | /* mxs chan ccw idx: 2 */ 63.218936 | 1) 1.875 us | } 63.218937 | 1) | mxs_dma_prep_slave_sg() { 63.218938 | 1) | /* mxs chan ccw idx: 3 */ 63.218939 | 1) 1.625 us | } 63.218939 | 1) 5.875 us | } 63.218940 | 1) | /* gpmi_chain_wait_ready */ 63.218941 | 1) | mxs_dma_prep_slave_sg() { 63.218942 | 1) | /* mxs chan ccw idx: 4 */ 63.218942 | 1) 1.625 us | } 63.218943 | 1) | /* gpmi_chain_data_read */ 63.218944 | 1) | mxs_dma_prep_slave_sg() { 63.218945 | 1) | /* mxs chan ccw idx: 5 */ 63.218947 | 1) 2.375 us | } 63.218948 | 1) 0.625 us | mxs_dma_tx_submit(); 63.218949 | 1) 1.000 us | mxs_dma_enable_chan(); 63.219276 | 0) 5.125 us | bch_irq(); <---- 63.219283 | 1) | /* jiffies left 250 */ 63.219285 | 1) ! 358.625 us | } 63.219286 | 1) 2.750 us | gpmi_count_bitflips(); 63.219289 | 1) ! 366.000 us | } 63.219290 | 1) | gpmi_ecc_read_page() { 63.219291 | 1) 0.750 us | gpmi_bch_layout_std(); 63.219293 | 1) | gpmi_nfc_exec_op() { 63.219294 | 1) | gpmi_chain_command() { 63.219295 | 1) | mxs_dma_prep_slave_sg() { 63.219295 | 0) 1.875 us | mxs_dma_int_handler(); <---- 63.219296 | 1) | /* mxs chan ccw idx: 6 */ 63.219297 | 1) 2.250 us | } 63.219298 | 1) | mxs_dma_prep_slave_sg() { 63.219298 | 0) 1.000 us | mxs_dma_tasklet(); 63.219299 | 1) | /* mxs chan ccw idx: 0 */ 63.219300 | 1) 1.625 us | } 63.219300 | 1) 6.375 us | } 63.219301 | 1) | gpmi_chain_command() { 63.219302 | 1) | mxs_dma_prep_slave_sg() { 63.219303 | 1) | /* mxs chan ccw idx: 1 */ 63.219304 | 1) 1.625 us | } 63.219305 | 1) | mxs_dma_prep_slave_sg() { 63.219306 | 1) | /* mxs chan ccw idx: 2 */ 63.219306 | 1) 1.875 us | } 63.219307 | 1) 6.000 us | } 63.219308 | 1) | /* gpmi_chain_wait_ready */ 63.219308 | 1) | mxs_dma_prep_slave_sg() { 63.219309 | 1) | /* mxs chan ccw idx: 3 */ 63.219310 | 1) 2.000 us | } 63.219311 | 1) | /* gpmi_chain_data_read */ 63.219312 | 1) | mxs_dma_prep_slave_sg() { 63.219313 | 1) | /* mxs chan ccw idx: 4 */ 63.219314 | 1) 1.750 us | } 63.219315 | 1) 0.625 us | mxs_dma_tx_submit(); 63.219316 | 1) 0.875 us | mxs_dma_enable_chan(); 64.224227 | 1) | /* jiffies left 0 */ In the first gpmi_nfc_exec_op, bch_irq comes first and gpmi_nfc_exec_op exits, but DMA IRQ still not happened yet until the middle of following gpmi_nfc_exec_op, the first DMA transfer index get messed and DMA get timeout. To fix the issue, when there is bch ops in DMA chain, the gpmi_nfc_exec_op should wait for both completions rather than bch completion only. Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op") Signed-off-by: Han Xu <han.xu@nxp.com> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201209035104.22679-3-han.xu@nxp.com
* mtd: rawnand: gpmi: Fix the driver only sense CS0 R/B issueHan Xu2020-12-102-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set the GPMI CTRL1 GANGED_RDYBUSY bit so driver can sense the R/B signal from all CS. For the NAND chip MT29F64G08AFAAAWP, only the first chip detected without the patch. [ 3.764118] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68 [ 3.770613] nand: Micron MT29F64G08AFAAAWP [ 3.774752] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448 [ 3.786421] Bad block table found at page 524160, version 0x01 [ 3.792730] Bad block table found at page 524032, version 0x01 After applying the patch [ 3.764445] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68 [ 3.770941] nand: Micron MT29F64G08AFAAAWP [ 3.775080] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448 [ 3.784390] nand: 2 chips detected [ 3.790900] Bad block table found at page 524160, version 0x01 [ 3.796776] Bad block table found at page 1048448, version 0x01 Signed-off-by: Han Xu <han.xu@nxp.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201209035104.22679-2-han.xu@nxp.com
* mtd: rawnand: gpmi: Use of_device_get_match_data()Fabio Estevam2020-12-101-9/+1
| | | | | | | | | | | The retrieval of driver data via of_device_get_match_data() can make the code simpler. Use of_device_get_match_data() to simplify the code. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201126030946.2058-1-festevam@gmail.com
* mtd: rawnand: gpmi: fix reference count leak in gpmi opsZhang Qilong2020-12-101-2/+6
| | | | | | | | | | | | | | | | | | pm_runtime_get_sync() will increment pm usage at first and it will resume the device later. If runtime of the device has error or device is in inaccessible state(or other error state), resume operation will fail. If we do not call put operation to decrease the reference, it will result in reference leak in the two functions(gpmi_init and gpmi_nfc_exec_op). Moreover, this device cannot enter the idle state and always stay busy or other non-idle state later. So we fixed it through adding pm_runtime_put_noidle. Fixes: 5bc6bb603b4d0 ("mtd: rawnand: gpmi: Fix suspend/resume problem") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Acked-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201107110552.1568742-1-zhangqilong3@huawei.com
* mtd: rawnand: gpmi: cleanup makefileMarco Felsch2020-12-101-2/+1
| | | | | | | | | | The extra gpmi_nand.o object is not needed anymore since commit 3045f8e36963 ("mtd: rawnand: gpmi: move all driver code into single file"). Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201007134533.31390-1-m.felsch@pengutronix.de
* mtd: rawnand: gpmi: Simplify with dev_err_probe()Krzysztof Kozlowski2020-09-301-4/+2
| | | | | | | | | Common pattern of handling deferred probe can be simplified with dev_err_probe(). Less code and the error value gets printed. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-3-krzk@kernel.org
* mtd: rawnand: Use nanddev_get/set_ecc_requirements() when relevantMiquel Raynal2020-09-281-6/+7
| | | | | | | Instead of accessing ->strength/step_size directly. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-15-miquel.raynal@bootlin.com
* mtd: rawnand: Use the new ECC engine type enumerationMiquel Raynal2020-09-281-1/+1
| | | | | | | | | | | | Mechanical switch from the legacy "mode" enumeration to the new "engine type" enumeration in drivers and board files. The device tree parsing is also updated to return the new enumeration from the old strings. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-11-miquel.raynal@bootlin.com
* mtd: rawnand: s/data_interface/interface_config/Miquel Raynal2020-06-261-3/+3
| | | | | | | | | | The name/suffix data_interface is a bit misleading in that the field or functions actually represent a configuration that can be applied by the controller/chip. Let's rename all fields/functions/hooks that are worth renaming. Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: Use nand_extract_bits()Miquel Raynal2020-05-311-164/+10
| | | | | | | | Drop the use of gpmi_copy_bits() in favor of the NAND helper nand_extract_bits(). Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200508171805.8627-1-miquel.raynal@bootlin.com
* mtd: rawnand: gpmi: Fix runtime PM imbalance in gpmi_nand_probeDinghao Liu2020-05-311-1/+1
| | | | | | | | | There is no reason that the failure of __gpmi_enable_clk() could lead to PM usage counter decrement. Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200522101713.24350-1-dinghao.liu@zju.edu.cn
* mtd: rawnand: gpmi: Fix runtime PM imbalance on errorDinghao Liu2020-05-311-1/+3
| | | | | | | | | | pm_runtime_get_sync() increments the runtime PM usage counter even when it returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced. Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200522095139.19653-1-dinghao.liu@zju.edu.cn
* mtd: rawnand: gpmi: Stop using nand_release()Miquel Raynal2020-05-311-1/+5
| | | | | | | | | | | | This helper is not very useful and very often people get confused: they use nand_release() instead of nand_cleanup(). Let's stop using nand_release() by calling mtd_device_unregister() and nand_cleanup() directly. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Han Xu <han.xu@nxp.com> Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-20-miquel.raynal@bootlin.com
* mtd: rawnand: Take check_only into accountBoris Brezillon2020-05-101-0/+3
| | | | | | | | | | | | ->exec_op() is passed a check_only argument that encodes when the controller should just check whether the operation is supported or not without executing it. Some controllers simply ignore this arguments, others don't but keep modifying some of the registers before returning. Let's fix all those drivers. Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200418194217.1016060-1-boris.brezillon@collabora.com
* mtd: rawnand: gpmi: Use dma_request_chan() instead dma_request_slave_channel()Peter Ujfalusi2020-03-111-10/+11
| | | | | | | | | | | dma_request_slave_channel() is a wrapper on top of dma_request_chan() eating up the error code. Use using dma_request_chan() directly to return the real error code. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-2-peter.ujfalusi@ti.com
* mtd: rawnand: gpmi: Restore nfc timing setup after suspend/resumeEsben Haabendal2020-01-171-0/+4
| | | | | | | | | | | | As we reset the GPMI block at resume, the timing parameters setup by a previous exec_op is lost. Rewriting GPMI timing registers on first exec_op after resume fixes the problem. Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op") Cc: stable@vger.kernel.org Signed-off-by: Esben Haabendal <esben@geanix.com> Acked-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: Fix suspend/resume problemEsben Haabendal2020-01-171-1/+6
| | | | | | | | | | | | | | | | On system resume, the gpmi clock must be enabled before accessing gpmi block. Without this, resume causes something like [ 661.348790] gpmi_reset_block(5cbb0f7e): module reset timeout [ 661.348889] gpmi-nand 1806000.gpmi-nand: Error setting GPMI : -110 [ 661.348928] PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -110 [ 661.348961] PM: Device 1806000.gpmi-nand failed to resume: error -110 Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op") Cc: stable@vger.kernel.org Signed-off-by: Esben Haabendal <esben@geanix.com> Acked-by: Han Xu <han.xu@nxp.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: remove double assignment to block_sizeColin Ian King2019-06-271-1/+1
| | | | | | | | | | The variable block_size is being assigned to itself and to geo->ecc_chunk_size. Clean up the double assignment by removing the assignment to itself. Addresses-Coverity: ("Evaluation order violation") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: Implement exec_opSascha Hauer2019-06-272-690/+440
| | | | | | | | | | | | | | | | | | | | | | | | The gpmi driver performance suffers from NAND operations being split in multiple small DMA transfers. This has been forced by the NAND layer in the former days, but now with exec_op we can use the controller as intended. With this patch gpmi_nfc_exec_op becomes the main entry point to NAND operations. Here all instructions are collected and chained as separate DMA transfers. In the end whole chain is fired and waited to be finished. gpmi_nfc_exec_op only does the hardware operations, bad block marker swapping and buffer scrambling is done by the callers. It's worth noting that the nand_*_op functions always take the buffer lengths for the data that the NAND chip actually transfers. When doing BCH we have to calculate the net data size from the raw data size in some places. This patch has been tested with 2048/64 and 2048/128 byte NAND on i.MX6q. mtd_oobtest, mtd_subpagetest and mtd_speedtest run without errors. nandbiterrs, nandpagetest and nandsubpagetest userspace tests from mtdutils run without errors and UBIFS can successfully be mounted. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* dmaengine: mxs: rename custom flagSascha Hauer2019-06-271-6/+11
| | | | | | | | | | The mxs dma driver uses the flags parameter in dmaengine_prep_slave_sg() for custom flags, but still uses the dmaengine specific names of the flags. Do a little bit better and at least give the flag a custom name. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* dmaengine: mxs: Add header file to be shared with gpmi nand driverSascha Hauer2019-06-271-22/+14
| | | | | | | | | | | | | The mxs dma driver can do PIO transfers. A pointer to the PIO words to transfer is passed in the struct scatterlist * argument of dmaengine_prep_slave_sg(). It's quite ugly and non obvious to cast u32 * to struct scatterlist * each time when calling dmaengine_prep_slave_sg(), so add a static inline wrapper function to be called by the user along with a description what is going on. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: drop unnecessary flagSascha Hauer2019-06-271-9/+5
| | | | | | | | | The DMA_PREP_INTERRUPT flag is no longer needed by the mxs DMA driver, drop it. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: use runtime PM to manage clocksSascha Hauer2019-06-271-25/+44
| | | | | | | | | | The gpmi driver aggressively en/disables the clocks between operations which has significant performance cost. Use runtime PM to get rid of this bottleneck. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: Drop unnecessary restoring of previous chipselectionSascha Hauer2019-06-271-14/+2
| | | | | | | | | | | The i.MX23 specific option read code is called right after nand_scan. We can rely on the NAND core having disabled the chipselect, so there's no point in restoring the original chip select after NAND operations. Drop it. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: remove unused parametersSascha Hauer2019-06-271-15/+19
| | | | | | | | | | | gpmi_ecc_read_page_data uses the page parameter only for a debug printf, so we can drop the parameter and the debug printf. Moving the oob delivery from gpmi_ecc_read_page_data to gpmi_ecc_read_page makes the oob_required parameter unnecessary aswell. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: read buf in nand_read_page_opSascha Hauer2019-06-271-8/+18
| | | | | | | | | | The driver calls nand_read_page_op without a buffer passed and then calls chip->legacy.read_buf to read the buffer afterwards which is the same as passing the buffer nand_read_page_op in the first place. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: Remove unnecessary variablesSascha Hauer2019-06-272-11/+6
| | | | | | | | | | this->page_buffer_virt and this->payload_virt are always set to the same value, so drop the former and just use the latter. Same for this->page_buffer_virt and this->payload_virt. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: remove unused variableSascha Hauer2019-06-271-3/+0
| | | | | | | | | The "private" member of struct gpmi_nand_data isn't used anywhere. Remove it. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* mtd: rawnand: gpmi: move all driver code into single fileSascha Hauer2019-06-274-1106/+1058
| | | | | | | | | | | | | This moves the whole driver into a single C file. The filename gpmi-lib implies that it implements library functions, but in fact there are several cases where functions in gpmi-lib.c call back into functions in gpmi-nand.c. With this one has to constantly jump between those two files, so moving it into a single file improves readability, even when the file gets quite large. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-03-22 08:48:04 +0000