summaryrefslogtreecommitdiffstats
path: root/drivers/net/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* net-caif-driver: add CAIF serial driver (ldisc)Sjur Braendeland2010-03-301-0/+1
| | | | | | | | | | | Add CAIF Serial driver. This driver is implemented as a line discipline. caif_serial uses the following module parameters: ser_use_stx - specifies if STart of frame eXtension is in use. ser_loop - sets the interface in loopback mode. Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Add Aeroflex Gaisler 10/100/1G Ethernet MAC driverKristoffer Glembo2010-02-171-0/+1
| | | | | | | | Adds device driver for Aeroflex Gaisler 10/100 and 10/100/1G Ethernet MAC IP cores. Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Makefile change for KSZ884X driverTristram Ha2010-02-121-0/+1
| | | | | | | Add Micrel KSZ884X network driver for KSZ8841/KSZ8842 PCI Ethernet chips. Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: macvtap driverArnd Bergmann2010-02-031-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | In order to use macvlan with qemu and other tools that require a tap file descriptor, the macvtap driver adds a small backend with a character device with the same interface as the tun driver, with a minimum set of features. Macvtap interfaces are created in the same way as macvlan interfaces using ip link, but the netif is just used as a handle for configuration and accounting, while the data goes through the chardev. Each macvtap interface has its own character device, simplifying permission management significantly over the generic tun/tap driver. Cc: Patrick McHardy <kaber@trash.net> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: David S. Miller" <davem@davemloft.net> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Or Gerlitz <ogerlitz@voltaire.com> Cc: netdev@vger.kernel.org Cc: bridge@lists.linux-foundation.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* NET: Add Qlogic ethernet driver for CNA devicesAmit Kumar Salecha2010-01-161-0/+1
| | | | | | | o Separate Ethernet driver for Qlogic CNA devices Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbevf: Kconfig, Makefile and DocumentationGreg Rose2010-01-101-0/+1
| | | | | | | | | Modifications for the Kconfig and network device Makefile to add the ixgbevf driver module to the kernel plus basic driver documentation. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* NET: Add Ethernet driver for Octeon MGMT devices.David Daney2009-12-171-0/+2
| | | | | | | | | | | | | | | | | | | | | The Octeon MGMT Ethernet ports are present in some members of the Octeon SOC family (cn52XX and cn56XX have them). The mdio bus connected to the MGMT PHYs is shared with the main octeon-ethernet driver, we force it to be loaded first by calling octeon_mdiobus_force_mod_depencency. The platform devices for the MGMT Ethernet ports are added in arch/mips/cavium-octeon/octeon-platform.c, and the register definitions for the ports live in arch/mips/include/asm/octeon/ along with their ilk. Although it currently is the only driver in drivers/net/octeon, the directory was created looking forward to the day that octeon-ethernet will move there from its current home in drivers/staging. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* net: add support for STMicroelectronics Ethernet controllers.Giuseppe Cavallaro2009-10-141-0/+1
| | | | | | | | | | | | | | | This is the driver for the ST MAC 10/100/1000 on-chip Ethernet controllers (Synopsys IP blocks). Driver documentation: o http://stlinux.com/drupal/kernel/network/stmmac Revisions: o http://stlinux.com/drupal/kernel/network/stmmac-driver-revisions Performances: o http://stlinux.com/drupal/benchmarks/networking/stmmac Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: VMware virtual Ethernet NIC driver: vmxnet3Shreyas Bhatewara2009-10-131-0/+1
| | | | | | | | | | | | | | | Ethernet NIC driver for VMware's vmxnet3 From: Shreyas Bhatewara <sbhatewara@vmware.com> This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3 Guests running on VMware hypervisors supporting vmxnet3 device will thus have access to improved network functionalities and performance. Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: Ronghua Zhang <ronghua@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Link in PHY drivers before others.David S. Miller2009-10-091-4/+4
| | | | | | | | | We need PHY drivers to initialize in a static kernel before the MAC drivers that use them. So link them in first. Based upon a report by Felix Radensky. Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: ks8851_mll ethernet network driverChoi, David2009-09-301-0/+1
| | | | | | | | | This is the first registration of ks8851 network driver with MLL(address/data multiplexed) interface. Signed-off-by : David J. Choi <david.choi@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* MIPS: BCM63xx: Add integrated ethernet mac support.Maxime Bizon2009-09-171-0/+1
| | | | | | | Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* net: add Xilinx emac lite device driverJohn Linn2009-08-201-0/+1
| | | | | | | | | | This patch adds support for the Xilinx Ethernet Lite device. The soft logic core from Xilinx is typically used on Virtex and Spartan designs attached to either a PowerPC or a Microblaze processor. Signed-off-by: Sadanand M <sadanan@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Micrel KS8851 SPI network driverBen Dooks2009-07-201-0/+1
| | | | | | | | Network driver for the SPI version of the Micrel KS8851 network chip. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* s6gmac: xtensa s6000 on-chip ethernet driverOskar Schirmer2009-06-221-0/+1
| | | | | | | | | | | | | The s6000 on-chip MAC supports 10/100/1000Mbit and is connected to an external PHY via MII or RGMII interface. [jw@emlix.com: don't use device->bus_id directly] Signed-off-by: Oskar Schirmer <os@emlix.com> Signed-off-by: Daniel Glockner <dg@emlix.com> Acked-by: "David S. Miller" <davem@davemloft.net> Signed-off-by: Johannes Weiner <jw@emlix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Zankel <chris@zankel.net>
* Merge branch 'master' of ↵David S. Miller2009-06-151-0/+1
|\ | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: Documentation/feature-removal-schedule.txt drivers/scsi/fcoe/fcoe.c net/core/drop_monitor.c net/core/net-traces.c
| * [SCSI] Merge branch 'linus'James Bottomley2009-06-121-1/+1
| |\ | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/message/fusion/mptsas.c fixed up conflict between req->data_len accessors and mptsas driver updates. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
| * | [SCSI] cnic: Add new Broadcom CNIC driver.Michael Chan2009-06-091-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The CNIC driver controls BNX2 hardware rings and resources used by iSCSI. Most hardware resources for iSCSI are separate from those used for ethernet networking. iSCSI uses a separate MAC address and IP address. The CNIC driver creates a UIO interface to handle the non-offloaded packets such as ARP, etc in userspace. Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* | | netdev: Added KS8842 driverRichard Ršöjfors2009-06-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a driver for the Micrel KS8842 ethernet switch. The supplied code is for driving the KS8842 through the Timberdale FPGA on the Russellville board, a development board for Intel Atom CPU in the automotive area. Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | Merge branch 'master' of ↵David S. Miller2009-06-031-1/+1
|\ \ \ | | |/ | |/| | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/forcedeth.c
| * | mac8390: fix regression caused during net_device_ops conversionFinn Thain2009-05-251-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | Changeset ca17584bf2ad1b1e37a5c0e4386728cc5fc9dabc ("mac8390: update to net_device_ops") broke mac8390 by adding 8390.o to the link. That meant that lib8390.c was included twice, once in mac8390.c and once in 8390.c, subject to different macros. This patch reverts that by avoiding the wrappers in 8390.c. They seem to be of no value since COMPAT_NET_DEV_OPS is going away soon. Tested with a Kinetics EtherPort card. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: Add TI DaVinci EMAC driverAnant Gole2009-05-181-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for TI DaVinci EMAC driver. TI DaVinci Ethernet Media Access Controller module is based upon TI CPPI 3.0 DMA engine and supports 10/100 Mbps on all and Gigabit modes on some TI devices. It supports MII/RMII and has up to 8Kbytes of internal descriptor memory. This driver has been working on several TI devices including DM644x, DM646x and DA830 platforms. The specs of this device are available at: http://www.ti.com/litv/pdf/sprue24a Signed-off-by: Anant Gole <anantgole@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | mdio: Add generic MDIO (clause 45) support functionsBen Hutchings2009-04-291-0/+1
| | | | | | | | | | | | | | | | These roughly mirror many of the MII library functions and are based on code from the sfc driver. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: add Xilinx ll_temac device driverGrant Likely2009-04-271-0/+2
|/ | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igbvf: add new driver to support 82576 virtual functionsAlexander Duyck2009-04-081-0/+1
| | | | | | | | | | | | | | | | | This adds an igbvf driver to handle virtual functions provided by the igb driver when SR-IOV has been enabled. A virtual function is a lightweight pci-e function that supports a single queue and shares resources with the 82576 physical function contained within the igb driver. To spawn virtual functions from the igb driver all that is needed is to enable CONFIG_PCI_IOV and have an 82576 Ethernet adapter on a system that supports SR-IOV in the BIOS. The virtual functions will appear after the interface is loaded. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Neterion: New driver: Kconfig and MakefileRamkrishna Vepa2009-04-021-0/+1
| | | | | | | | | | | | | | | | | - Kconfig and Makefile related changes for vxge driver. - No changes in current submission. - Changes from previous submission - - Incorporated the following review comments as per Bill Flink: - Add dependancy on INET along with PCI - Remove dependancy on INET_LRO and add GRO support. - Made this patch as last patch as per Ben Hutchings comments. Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com> Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.Thierry Reding2009-03-271-0/+1
| | | | | | | | | | | | | | This patch adds a platform device driver that supports the OpenCores 10/100 Mbps Ethernet MAC. The driver expects three resources: one IORESOURCE_MEM resource defines the memory region for the core's memory-mapped registers while a second IORESOURCE_MEM resource defines the network packet buffer space. The third resource, of type IORESOURCE_IRQ, associates an interrupt with the driver. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2009-03-171-0/+2
|\ | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/igb/igb_main.c drivers/net/qlge/qlge_main.c drivers/net/wireless/ath9k/ath9k.h drivers/net/wireless/ath9k/core.h drivers/net/wireless/ath9k/hw.c
| * net: Add be2net driver.Sathya Perla2009-03-111-0/+1
| | | | | | | | | | Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * dnet: Dave DNET ethernet controller driver (updated)Ilya Yanok2009-03-111-0/+1
| | | | | | | | | | | | | | | | | | Driver for Dave DNET ethernet controller found on Dave/DENX QongEVB-LITE FPGA. Heavily based on Dave sources, I've just adopted it to current kernel version and done some code cleanup. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'master' of /home/davem/src/GIT/linux-2.6/David S. Miller2009-02-241-0/+1
|\|
| * atl1c: Atheros L1C Gigabit Ethernet driverJie Yang2009-02-181-0/+1
| | | | | | | | | | | | | | Supporting AR8131, and AR8132. Signed-off-by: Jie Yang <jie.yang@atheros.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | netdev: Merge UCC and gianfar MDIO bus driversAndy Fleming2009-02-041-2/+3
|/ | | | | | | | The MDIO bus drivers for the UCC and gianfar ethernet controllers are essentially the same. There's no reason to duplicate that much code. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* i2400m: Makefile and KconfigInaky Perez-Gonzalez2009-01-071-0/+1
| | | | | | | | Integrate the i2400m driver into the kernel's build and Kconfig. Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* smsc9420: SMSC LAN9420 10/100 PCI ethernet adapterSteve Glendinning2008-12-111-0/+1
| | | | | | | | | | | This patch adds a driver for the LAN9240 PCI ethernet adapter. Changes since initial submission: - debug msg_level has been changed to use standard definitions - convert to use net_device_ops Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ne-h8300: convert to net_device_opsStephen Hemminger2008-12-031-1/+1
| | | | | | | Another device using 8390 library that needs converting. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* hydra: convert to net_device_opsStephen Hemminger2008-12-031-1/+1
| | | | | | | Another device using 8390 library that needs converting. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* zorro8390: convert to net_device_opsStephen Hemminger2008-12-031-1/+1
| | | | | | | Another device using 8390 library that needs converting. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mac8390: update to net_device_opsStephen Hemminger2008-12-021-1/+1
| | | | | | | | Another related 8390 driver. Since this is for nubus, not sure if anyone still has the hardware? Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2008-11-261-1/+1
|\ | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/hp-plus.c drivers/net/wireless/ath5k/base.c drivers/net/wireless/ath9k/recv.c net/wireless/reg.c
| * net/hp-plus: fix link errorsRandy Dunlap2008-11-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix hp-plus driver link errors. Builds as loadable module and kernel image driver. All drivers that use 8390.o or 8390p.o that will build on i386 with MCA/PCI/EISA/ISA were built successfully both =m and =y. drivers/built-in.o: In function `hpp_open': hp-plus.c:(.text+0xac06c): undefined reference to `eip_interrupt' hp-plus.c:(.text+0xac0d7): undefined reference to `eip_open' drivers/built-in.o: In function `hpp_close': hp-plus.c:(.text+0xac1bb): undefined reference to `eip_close' drivers/built-in.o: In function `hpp_probe1': hp-plus.c:(.init.text+0xa98a): undefined reference to `NS8390p_init' drivers/built-in.o: In function `hp_plus_probe': (.init.text+0xa9fe): undefined reference to `__alloc_eip_netdev' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | SMSC LAN911x and LAN921x vendor driverSteve Glendinning2008-11-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Attached is a driver for SMSC's LAN911x and LAN921x families of embedded ethernet controllers. There is an existing smc911x driver in the tree; this is intended to replace it. Dustin McIntire (the author of the smc911x driver) has expressed his support for switching to this driver. This driver contains workarounds for all known hardware issues, and has been tested on all flavours of the chip on multiple architectures. This driver now uses phylib, so this patch also adds support for the device's internal phy Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com> Signed-off-by: Dustin Mcintire <dustin@sensoria.com> Signed-off-by: Bill Gatliff <bgat@billgatliff.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | The overdue eepro100 removal.Adrian Bunk2008-10-311-1/+0
|/ | | | | | | Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* xtensa: Add support for the Sonic Ethernet device for the XT2000 board.Chris Zankel2008-10-211-0/+2
| | | | | | | Add support for the on-board Sonic Ethernet device for the XT2000 evaluation board. Signed-off-by: Chris Zankel <chris@zankel.net>
* qlge: New Qlogic 10Gb Ethernet Driver.Ron Mercer2008-09-181-0/+1
| | | | | Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* jme: JMicron Gigabit Ethernet DriverGuo-Fu Tseng2008-09-181-0/+1
| | | | | | | | Supporting JMC250, and JMC260. Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Acked-and-tested-by: Ethan Hsiao <ethanhsiao@jmicron.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* enic: add Cisco 10G Ethernet NIC driverScott Feldman2008-09-181-0/+1
| | | | | Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* atl2: add atl2 driverChris Snook2008-09-181-0/+1
| | | | | | | | | Driver for Atheros L2 10/100 network device. Includes necessary changes for Kconfig, Makefile, and pci_ids.h. Signed-off-by: Chris Snook <csnook@redhat.com> Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* hp-plus: fix link objectsRandy Dunlap2008-09-031-1/+1
| | | | | | | | | | | | | | | | | | Fix hp-plus Makefile object file: drivers/built-in.o: In function `hpp_open': hp-plus.c:(.text+0xaf445): undefined reference to `ei_interrupt' hp-plus.c:(.text+0xaf4ac): undefined reference to `ei_open' drivers/built-in.o: In function `hpp_close': hp-plus.c:(.text+0xaf59d): undefined reference to `ei_close' drivers/built-in.o: In function `hpp_probe1': hp-plus.c:(.init.text+0x7314): undefined reference to `ei_poll' drivers/built-in.o: In function `hp_plus_probe': (.init.text+0x7407): undefined reference to `__alloc_ei_netdev' make[1]: *** [.tmp_vmlinux1] Error 1 Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* atl1e: Atheros L1E Gigabit Ethernet driverJie Yang2008-07-221-0/+1
| | | | | | | | Full patch for the Atheros L1E Gigabit Ethernet driver. Supportring AR8121, AR8113 and AR8114 Signed-off-by: Jie Yang <jie.yang @atheros.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-24 23:20:05 +0000