| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| |
|
|
|
| |
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
| |
The Compressed LIP region is used to hold a limited number of Local
IPv6 addresses. This region is primarily used to reduce the TCAM
space consumed for an IPv6 offloaded connection. A 128-bit LIP will
be reduced to 13-bit and stored in the TCAM if there is a match
between the IPv6 tuple's LIP and the one stored in the CLIP region.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Newer firmware can post CPL_SGE_EGR_UPDATE message encapsulated in a
CPL_FW4_MSG as follows
flit0 rss_header (if DropRSS == 0 in IQ context)
flit1 CPL_FW4_MSG cpl
flit2 rss_header w/opcode CPL_SGE_EGR_UPDATE
flit3 CPL_SGE_EGR_UPDATE cpl
So FW4_MSG CPLs with a newly created type of FW_TYPE_RSSCPL have the
CPL_SGE_EGR_UPDATE CPL message in flit 2 of the FW4_MSG. Firmware can still
post regular CPL_SGE_EGR_UPDATE messages, so the drivers need to handle
both.
This patch also writes a new parameter to firmware requesting encapsulated
EGR_UPDATE. This allows firmware with this support to not break older drivers.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
| |
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
It enables establishing active open connection using fw_ofld_connection work
request when cpl_act_open_rpl says TCAM full error which may be because
of LE hash collision. Current support is only for IPv4 active open connections.
Sets ntuple bits in active open requests. For T4 firmware greater than 1.4.10.0
ntuple bits are required to be set.
Adds nocong and enable_ecn module parameter options.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
[ Move all FW return values to t4fw_api.h. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The T4 architecture is capable of filtering ingress packets at line rate
using the rule in TCAM. If packet hits a rule in the TCAM then it can be either
dropped or passed to the receive queues based on a rule settings.
This patch adds framework for managing filters and to use T4's filter
capabilities. It constructs a Firmware Filter Work Request which writes the
filter at a specified index to get the work done. It hosts shadow copy of
ingress filter entry to check field size limitations and save memory in the
case where the filter table is large.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
updates).
This patch contains updates to firmware/hardware header files shared
between csiostor and cxgb4/cxgb4vf, and the resulting changes to the
cxgb4/cxgb4vf source files.
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds a new common code routine to upgrade an adapter's
firmware. This routine handles all of the complexities of working with the
the existing adapter firmware in order to quiesce the adapter and uP, etc.
For an automatic upgrade it will send a HELLO command to check if cxgb4
want/can upgrade firmware, i.e. if cxgb4 is MASTER and has newer firmware
that it wants to load and call the new common code routine t4_fw_upgrade.
Note that it should not issue a RESET command after a successful firmware
upgrade.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
In case if user defined configuration file at /lib/firmware/cxgb4/t4-config.txt
location and also factory default configuration file written to FLASH are not
present then driver will use hardwired configuration settings.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Starting with T4 firmware version 1.3.11.0 the firmware now supports device
configuration via a Firmware Configuration File. The Firmware Configuration
File was primarily developed in order to centralize all of the configuration,
resource allocation, etc. for Unified Wire operation where multiple
Physical / Virtual Function Drivers would be using a T4 adapter simultaneously.
The Firmware Configuration file can live in three locations as shown below
in order of precedence.
1) User defined configuration file: /lib/firmware/cxgb4/t4-config.txt
2) Factory Default configuration file written to FLASH within
the manufacturing process.
3) Hardwired driver configuration.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds new enums and macros to enable T4 configuration file support. It
also removes duplicate macro definitions.
It fixes the build failure in cxgb4vf driver introduced because of old macro
definition removal.
It also performs SGE initialization based on T4 configuration file is provided
or not. If it is provided then it uses the parameters provided in it otherwise
it uses hard coded values.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
recover LLD EQs for DB drop interrupts. This includes adding a new
db_lock, a spin lock disabling BH too, used by the recovery thread and
the ring_tx_db() paths to allow db drop recovery.
Clean up initial DB avoidance code.
Add read_eq_indices() - this allows the LLD to use the PCIe mw to
efficiently read hw eq contexts.
Add cxgb4_sync_txq_pidx() - called by iw_cxgb4 to sync up the sw/hw
pidx value.
Add flush_eq_cache() and cxgb4_flush_eq_cache(). This allows iw_cxgb4
to flush the sge eq context cache before beginning db drop recovery.
Add module parameter, dbfoifo_int_thresh, to allow tuning the db
interrupt threshold value.
Add dbfifo_int_thresh to cxgb4_lld_info so iw_cxgb4 knows the threshold.
Add module parameter, dbfoifo_drain_delay, to allow tuning the amount
of time delay between DB FULL and EMPTY upcalls to iw_cxgb4.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
|
Moves the drivers for the Chelsio chipsets into
drivers/net/ethernet/chelsio/ and the necessary Kconfig and Makefile
changes.
CC: Divy Le Ray <divy@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
