summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/faraday/ftgmac100.c
Commit message (Collapse)AuthorAgeFilesLines
* drivers/net/ftgmac100: fix DHCP potential failure with systemdHeyi Guo2022-02-231-2/+11
| | | | | | | | | | | | | | | | | | | | | | | DHCP failures were observed with systemd 247.6. The issue could be reproduced by rebooting Aspeed 2600 and then running ifconfig ethX down/up. It is caused by below procedures in the driver: 1. ftgmac100_open() enables net interface and call phy_start() 2. When PHY is link up, it calls netif_carrier_on() and then adjust_link callback 3. ftgmac100_adjust_link() will schedule the reset task 4. ftgmac100_reset_task() will then reset the MAC in another schedule After step 2, systemd will be notified to send DHCP discover packet, while the packet might be corrupted by MAC reset operation in step 4. Call ftgmac100_reset() directly instead of scheduling task to fix the issue. Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/ftgmac100: adjust code place for function call dependencyHeyi Guo2022-02-231-111/+111
| | | | | | | | This is to prepare for ftgmac100_adjust_link() to call ftgmac100_reset() directly. Only code places are changed. Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/ftgmac100: refactor ftgmac100_reset_task to enable direct ↵Heyi Guo2022-02-231-3/+9
| | | | | | | | | | function call This is to prepare for ftgmac100_adjust_link() to call reset function directly, instead of task schedule. Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethtool: extend ringparam setting/getting API with rx_buf_lenHao Chen2021-11-221-4/+10
| | | | | | | | | | Add two new parameters kernel_ringparam and extack for .get_ringparam and .set_ringparam to extend more ring params through netlink. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethernet: make more use of device_get_ethdev_address()Jakub Kicinski2021-10-071-3/+2
| | | | | | | | | | | | Convert a few drivers to device_get_ethdev_address(), saving a few LoC. The check if addr is valid in netsec is superfluous, device_get_ethdev_addr() already checks that (in fwnode_get_mac_addr()). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* eth: fwnode: remove the addr len from mac helpersJakub Kicinski2021-10-071-1/+1
| | | | | | | | | | All callers pass in ETH_ALEN and the function itself will return -EINVAL for any other address length. Just assume it's ETH_ALEN like all other mac address helpers (nvm, of, platform). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* eth: fwnode: change the return type of mac address helpersJakub Kicinski2021-10-071-3/+1
| | | | | | | | | | | | | | fwnode_get_mac_address() and device_get_mac_address() return a pointer to the buffer that was passed to them on success or NULL on failure. None of the callers care about the actual value, only if it's NULL or not. These semantics differ from of_get_mac_address() which returns an int so to avoid confusion make the device helpers return an errno. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethernet: use eth_hw_addr_set() instead of ether_addr_copy()Jakub Kicinski2021-10-021-2/+2
| | | | | | | | | | | | | Convert Ethernet from ether_addr_copy() to eth_hw_addr_set(): @@ expression dev, np; @@ - ether_addr_copy(dev->dev_addr, np) + eth_hw_addr_set(dev, np) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* dev_ioctl: split out ndo_eth_ioctlArnd Bergmann2021-07-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | Most users of ndo_do_ioctl are ethernet drivers that implement the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP. Separate these from the few drivers that use ndo_do_ioctl to implement SIOCBOND, SIOCBR and SIOCWANDEV commands. This is a purely cosmetic change intended to help readers find their way through the implementation. Cc: Doug Ledford <dledford@redhat.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Leon Romanovsky <leon@kernel.org> Cc: linux-rdma@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ftgmac100: add missing error return code in ftgmac100_probe()Yang Yingliang2021-05-231-1/+5
| | | | | | | | | | | | The variables will be free on path err_phy_connect, it should return error code, or it will cause double free when calling ftgmac100_remove(). Fixes: bd466c3fb5a4 ("net/faraday: Support NCSI mode") Fixes: 39bfab8844a0 ("net: ftgmac100: Add support for DT phy-handle property") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Restart MAC HW onceDylan Hung2021-03-121-0/+1
| | | | | | | | | | | | The interrupt handler may set the flag to reset the mac in the future, but that flag is not cleared once the reset has occurred. Fixes: 10cbd6407609 ("ftgmac100: Rework NAPI & interrupts handling") Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge https://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2020-11-191-0/+4
|\ | | | | | | Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: ftgmac100: Fix crash when removing driverJoel Stanley2020-11-171-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific)) in net/core/dev.c due to still having the NC-SI packet handler registered. # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind ------------[ cut here ]------------ kernel BUG at net/core/dev.c:10254! Internal error: Oops - BUG: 0 [#1] SMP ARM CPU: 0 PID: 115 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00007-g02e0365710c4 #46 Hardware name: Generic DT based system PC is at netdev_run_todo+0x314/0x394 LR is at cpumask_next+0x20/0x24 pc : [<806f5830>] lr : [<80863cb0>] psr: 80000153 sp : 855bbd58 ip : 00000001 fp : 855bbdac r10: 80c03d00 r9 : 80c06228 r8 : 81158c54 r7 : 00000000 r6 : 80c05dec r5 : 80c05d18 r4 : 813b9280 r3 : 813b9054 r2 : 8122c470 r1 : 00000002 r0 : 00000002 Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none Control: 00c5387d Table: 85514008 DAC: 00000051 Process sh (pid: 115, stack limit = 0x7cb5703d) ... Backtrace: [<806f551c>] (netdev_run_todo) from [<80707eec>] (rtnl_unlock+0x18/0x1c) r10:00000051 r9:854ed710 r8:81158c54 r7:80c76bb0 r6:81158c10 r5:8115b410 r4:813b9000 [<80707ed4>] (rtnl_unlock) from [<806f5db8>] (unregister_netdev+0x2c/0x30) [<806f5d8c>] (unregister_netdev) from [<805a8180>] (ftgmac100_remove+0x20/0xa8) r5:8115b410 r4:813b9000 [<805a8160>] (ftgmac100_remove) from [<805355e4>] (platform_drv_remove+0x34/0x4c) Fixes: bd466c3fb5a4 ("net/faraday: Support NCSI mode") Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: ftgmac100: add handling of mdio/phy nodes for ast2400/2500Ivan Mikhaylov2020-11-021-2/+18
| | | | | | | | | | | | | | | | | | | | phy-handle can't be handled well for ast2400/2500 which has an embedded MDIO controller. Add ftgmac100_mdio_setup for ast2400/2500 and initialize PHYs from mdio child node with of_mdiobus_register. Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: ftgmac100: move phy connect out from ftgmac100_setup_mdioIvan Mikhaylov2020-11-021-50/+54
|/ | | | | | | | | Split MDIO registration and PHY connect into ftgmac100_setup_mdio and ftgmac100_mii_probe. Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: ftgmac100: Fix Aspeed ast2600 TX hang issueDylan Hung2020-10-161-0/+5
| | | | | | | | | | | The new HW arbitration feature on Aspeed ast2600 will cause MAC TX to hang when handling scatter-gather DMA. Disable the problematic feature by setting MAC register 0x58 bit28 and bit27. Fixes: 39bfab8844a0 ("net: ftgmac100: Add support for DT phy-handle property") Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net/faraday: fix grammar in function ftgmac100_setup_clk() in ftgmac100.cHu Haowen2020-04-011-1/+1
| | | | | | | "its not" is wrong. The words should be "it's not". Signed-off-by: Hu Haowen <xianfengting221@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Remove redundant judgementtangbin2020-03-111-3/+0
| | | | | | | | | In this function, ftgmac100_probe() can be triggered only if the platform_device and platform_driver matches, so the judgement at the beginning is redundant. Signed-off-by: tangbin <tangbin@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/faraday: Delete driver version from the driversLeon Romanovsky2020-03-031-2/+0
| | | | | | | Use general linux kernel version instead of static driver version. Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: convert suitable network drivers to use phy_do_ioctlHeiner Kallweit2020-01-211-10/+1
| | | | | | | | | Convert suitable network drivers to use phy_do_ioctl. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* netdev: pass the stuck queue to the timeout handlerMichael S. Tsirkin2019-12-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'docs-5.5a' of git://git.lwn.net/linuxLinus Torvalds2019-12-021-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull Documentation updates from Jonathan Corbet: "Here are the main documentation changes for 5.5: - Various kerneldoc script enhancements. - More RST conversions; those are slowing down as we run out of things to convert, but we're a ways from done still. - Dan's "maintainer profile entry" work landed at last. Now we just need to get maintainers to fill in the profiles... - A reworking of the parallel build setup to work better with a variety of systems (and to not take over huge systems entirely in particular). - The MAINTAINERS file is now converted to RST during the build. Hopefully nobody ever tries to print this thing, or they will need to load a lot of paper. - A script and documentation making it easy for maintainers to add Link: tags at commit time. Also included is the removal of a bunch of spurious CR characters" * tag 'docs-5.5a' of git://git.lwn.net/linux: (91 commits) docs: remove a bunch of stray CRs docs: fix up the maintainer profile document libnvdimm, MAINTAINERS: Maintainer Entry Profile Maintainer Handbook: Maintainer Entry Profile MAINTAINERS: Reclaim the P: tag for Maintainer Entry Profile docs, parallelism: Rearrange how jobserver reservations are made docs, parallelism: Do not leak blocking mode to other readers docs, parallelism: Fix failure path and add comment Documentation: Remove bootmem_debug from kernel-parameters.txt Documentation: security: core.rst: fix warnings Documentation/process/howto/kokr: Update for 4.x -> 5.x versioning Documentation/translation: Use Korean for Korean translation title docs/memory-barriers.txt: Remove remaining references to mmiowb() docs/memory-barriers.txt/kokr: Update I/O section to be clearer about CPU vs thread docs/memory-barriers.txt/kokr: Fix style, spacing and grammar in I/O section Documentation/kokr: Kill all references to mmiowb() docs/memory-barriers.txt/kokr: Rewrite "KERNEL I/O BARRIER EFFECTS" section docs: Add initial documentation for devfreq Documentation: Document how to get links with git am docs: Add request_irq() documentation ...
| * docs: fix some broken referencesMauro Carvalho Chehab2019-10-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | There are a number of documentation files that got moved or renamed. update their references. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by: Shannon Nelson <snelson@pensando.io> Acked-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # RISC-V Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* | net: of_get_phy_mode: Change API to solve int/unit warningsAndrew Lunn2019-11-041-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Before this change of_get_phy_mode() returned an enum, phy_interface_t. On error, -ENODEV etc, is returned. If the result of the function is stored in a variable of type phy_interface_t, and the compiler has decided to represent this as an unsigned int, comparision with -ENODEV etc, is a signed vs unsigned comparision. Fix this problem by changing the API. Make the function return an error, or 0 on success, and pass a pointer, of type phy_interface_t, where the phy mode should be stored. v2: Return with *interface set to PHY_INTERFACE_MODE_NA on error. Add error checks to all users of of_get_phy_mode() Fixup a few reverse christmas tree errors Fixup a few slightly malformed reverse christmas trees v3: Fix 0-day reported errors. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2019-11-021-13/+12
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | The only slightly tricky merge conflict was the netdevsim because the mutex locking fix overlapped a lot of driver reload reorganization. The rest were (relatively) trivial in nature. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | net: ethernet: ftgmac100: Fix DMA coherency issue with SW checksumBenjamin Herrenschmidt2019-10-281-13/+12
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We are calling the checksum helper after the dma_map_single() call to map the packet. This is incorrect as the checksumming code will touch the packet from the CPU. This means the cache won't be properly flushes (or the bounce buffering will leave us with the unmodified packet to DMA). This moves the calculation of the checksum & vlan tags to before the DMA mapping. This also has the side effect of fixing another bug: If the checksum helper fails, we goto "drop" to drop the packet, which will not unmap the DMA mapping. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Fixes: 05690d633f30 ("ftgmac100: Upgrade to NETIF_F_HW_CSUM") Reviewed-by: Vijay Khemka <vijaykhemka@fb.com> Tested-by: Vijay Khemka <vijaykhemka@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* / net: ftgmac100: Ungate RCLK for RMII on ASPEED MACsAndrew Jeffery2019-10-111-10/+40
|/ | | | | | | | The 50MHz RCLK has to be enabled before the RMII interface will function. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ftgmac100: Add support for DT phy-handle propertyAndrew Jeffery2019-08-021-4/+33
| | | | | | | | | | | | | | | | | | | | | phy-handle is necessary for the AST2600 which separates the MDIO controllers from the MAC. I've tried to minimise the intrusion of supporting the AST2600 to the FTGMAC100 by leaving in place the existing MDIO support for the embedded MDIO interface. The AST2400 and AST2500 continue to be supported this way, as it avoids breaking/reworking existing devicetrees. The AST2600 support by contrast requires the presence of the phy-handle property in the MAC devicetree node to specify the appropriate PHY to associate with the MAC. In the event that someone wants to specify the MDIO bus topology under the MAC node on an AST2400 or AST2500, the current auto-probe approach is done conditional on the absence of an "mdio" child node of the MAC. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Fix build.David S. Miller2019-07-231-1/+1
| | | | | | | | | | | drivers/net/ethernet/faraday/ftgmac100.c:777:13: error: 'skb_frag_t {aka struct bio_vec}' has no member named 'size' Fallout from the skb_frag_t conversion to bio_vec, simply use skb_frag_size(). Fixes: b8b576a16f79 ("net: Rename skb_frag_t size to bv_len") Reported-by: René van Dorst <opensource@vdorst.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'v5.2-rc4' into mauroJonathan Corbet2019-06-141-14/+1
|\ | | | | | | | | We need to pick up post-rc1 changes to various document files so they don't get lost in Mauro's massive RST conversion push.
| * treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 61Thomas Gleixner2019-05-241-14/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 675 mass ave cambridge ma 02139 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 441 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc) Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | docs: fix broken documentation linksMauro Carvalho Chehab2019-06-081-1/+1
|/ | | | | | | | | | | | Mostly due to x86 and acpi conversion, several documentation links are still pointing to the old file. Fix them. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com> Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com> Acked-by: Mark Brown <broonie@kernel.org> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* drivers: net: Remove unnecessary semicolonYueHaibing2019-03-011-1/+1
| | | | | | | | | | | | | | | | drivers/net/dsa/mt7530.c:649:3-4: Unneeded semicolon drivers/net/ethernet/cisco/enic/enic_clsf.c:35:2-3: Unneeded semicolon drivers/net/ethernet/faraday/ftgmac100.c:1640:2-3: Unneeded semicolon drivers/net/ethernet/mediatek/mtk_eth_soc.c:229:2-3: Unneeded semicolon drivers/net/usb/sr9700.c:437:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Sean Wang <sean.wang@mediatek.com> for mt7530 and mtk_eth_soc Signed-off-by: David S. Miller <davem@davemloft.net>
* cross-tree: phase out dma_zalloc_coherent()Luis Chamberlain2019-01-081-8/+6
| | | | | | | | | | | | | | | | | | | We already need to zero out memory for dma_alloc_coherent(), as such using dma_zalloc_coherent() is superflous. Phase it out. This change was generated with the following Coccinelle SmPL patch: @ replace_dma_zalloc_coherent @ expression dev, size, data, handle, flags; @@ -dma_zalloc_coherent(dev, size, handle, flags) +dma_alloc_coherent(dev, size, handle, flags) Suggested-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> [hch: re-ran the script on the latest tree] Signed-off-by: Christoph Hellwig <hch@lst.de>
* net: faraday: fix return type of ndo_start_xmit functionYueHaibing2018-09-261-2/+2
| | | | | | | | | | | | The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, so make sure the implementation in this driver has returns 'netdev_tx_t' value, and change the function return type to netdev_tx_t. Found by coccinelle. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: Add helper for set_pauseparam for Asym PauseAndrew Lunn2018-09-121-14/+3
| | | | | | | | | ethtool can be used to enable/disable pause. Add a helper to configure the PHY when asym pause is supported. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: Add helper for MACs which support asym pauseAndrew Lunn2018-09-121-2/+1
| | | | | | | | | Rather than have the MAC drivers manipulate phydev members to indicate they support Asym Pause, add a helper function. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/ncsi: Silence debug messagesJoel Stanley2018-06-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In normal operation we see this series of messages as the host drives the network device: ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config ftgmac100 1e660000.ethernet eth0: NCSI interface down ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI interface up ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config ftgmac100 1e660000.ethernet eth0: NCSI interface down ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0 ftgmac100 1e660000.ethernet eth0: NCSI interface up This makes all of these messages netdev_dbg. They are still useful to debug eg. misbehaving network device firmware, but we do not need them filling up the kernel logs in normal operation. Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ftgmac100: Request clock and set speedJoel Stanley2017-10-181-0/+26
| | | | | | | | | | | | | | | | | According to the ASPEED datasheet, gigabit speeds require a clock of 100MHz or higher. Other speeds require 25MHz or higher. This patch configures a 100MHz clock if the system has a direct-attached PHY, or 25MHz if the system is running NC-SI which is limited to 100MHz. There appear to be no other upstream users of the FTGMAC100 driver it is hard to know the clocking requirements of other platforms. Therefore a conservative approach was taken with enabling clocks. If the platform is not ASPEED, both requesting the clock and configuring the speed is skipped. Signed-off-by: Joel Stanley <joel@jms.id.au> Tested-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-09-011-1/+0
|\ | | | | | | | | | | Three cases of simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ftgmac100: Fix oops in probe on failure to find associated PHYAndrew Jeffery2017-08-221-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | netif_napi_del() should be paired with netif_napi_add(), however no such call takes place in ftgmac100_probe(). This triggers a NULL pointer dereference if e.g. no PHY is found by the MDIO probe: [ 2.770000] libphy: Fixed MDIO Bus: probed [ 2.770000] ftgmac100 1e660000.ethernet: Generated random MAC address 66:58:c0:5a:50:b8 [ 2.790000] libphy: ftgmac100_mdio: probed [ 2.790000] ftgmac100 1e660000.ethernet (unnamed net_device) (uninitialized): eth%d: no PHY found [ 2.790000] ftgmac100 1e660000.ethernet: MII Probe failed! [ 2.810000] Unable to handle kernel NULL pointer dereference at virtual address 00000004 [ 2.810000] pgd = 80004000 [ 2.810000] [00000004] *pgd=00000000 [ 2.810000] Internal error: Oops: 805 [#1] ARM [ 2.810000] CPU: 0 PID: 1 Comm: swapper Not tainted 4.10.17-1a4df30c39cf5ee0e3d2528c409787ccbb4a672a #1 [ 2.810000] Hardware name: ASpeed SoC [ 2.810000] task: 9e421b60 task.stack: 9e4a0000 [ 2.810000] PC is at netif_napi_del+0x74/0xa4 [ 2.810000] LR is at ftgmac100_probe+0x290/0x674 [ 2.810000] pc : [<80331004>] lr : [<80292b30>] psr: 60000013 [ 2.810000] sp : 9e4a1d70 ip : 9e4a1d88 fp : 9e4a1d84 [ 2.810000] r10: 9e565000 r9 : ffffffed r8 : 00000007 [ 2.810000] r7 : 9e565480 r6 : 9ec072c0 r5 : 00000000 r4 : 9e5654d8 [ 2.810000] r3 : 9e565530 r2 : 00000000 r1 : 00000000 r0 : 9e5654d8 [ 2.810000] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 2.810000] Control: 00c5387d Table: 80004008 DAC: 00000055 [ 2.810000] Process swapper (pid: 1, stack limit = 0x9e4a0188) [ 2.810000] Stack: (0x9e4a1d70 to 0x9e4a2000) [ 2.810000] 1d60: 9e565000 9e549e10 9e4a1dcc 9e4a1d88 [ 2.810000] 1d80: 80292b30 80330f9c ffffffff 9e4a1d98 80146058 9ec072c0 00009e10 00000000 [ 2.810000] 1da0: 9e549e18 9e549e10 ffffffed 805f81f4 fffffdfb 00000000 00000000 00000000 [ 2.810000] 1dc0: 9e4a1dec 9e4a1dd0 80243df8 802928ac 9e549e10 8062cbd8 8062cbe0 805f81f4 [ 2.810000] 1de0: 9e4a1e24 9e4a1df0 80242178 80243da4 803001d0 802ffa60 9e4a1e24 9e549e10 [ 2.810000] 1e00: 9e549e44 805f81f4 00000000 00000000 805b8840 8058a6b0 9e4a1e44 9e4a1e28 [ 2.810000] 1e20: 80242434 80241f04 00000000 805f81f4 80242344 00000000 9e4a1e6c 9e4a1e48 [ 2.810000] 1e40: 80240148 80242350 9e425bac 9e4fdc90 9e790e94 805f81f4 9e790e60 805f5640 [ 2.810000] 1e60: 9e4a1e7c 9e4a1e70 802425dc 802400d8 9e4a1ea4 9e4a1e80 80240ba8 802425c0 [ 2.810000] 1e80: 8050b6ac 9e4a1e90 805f81f4 ffffe000 805b8838 80616720 9e4a1ebc 9e4a1ea8 [ 2.810000] 1ea0: 80243068 80240a68 805ab24c ffffe000 9e4a1ecc 9e4a1ec0 80244a38 80242fec [ 2.810000] 1ec0: 9e4a1edc 9e4a1ed0 805ab264 80244a04 9e4a1f4c 9e4a1ee0 8058ae70 805ab258 [ 2.810000] 1ee0: 80032c68 801e3fd8 8052f800 8041af2c 9e4a1f4c 9e4a1f00 80032f90 8058a6bc [ 2.810000] 1f00: 9e4a1f2c 9e4a1f10 00000006 00000006 00000000 8052f220 805112f0 00000000 [ 2.810000] 1f20: 9e4a1f4c 00000006 80616720 805cf400 80616720 805b8838 80616720 00000057 [ 2.810000] 1f40: 9e4a1f94 9e4a1f50 8058b040 8058add0 00000006 00000006 00000000 8058a6b0 [ 2.810000] 1f60: 3940bf3d 00000007 f115c2e8 00000000 803fd158 00000000 00000000 00000000 [ 2.810000] 1f80: 00000000 00000000 9e4a1fac 9e4a1f98 803fd170 8058af38 00000000 803fd158 [ 2.810000] 1fa0: 00000000 9e4a1fb0 8000a5e8 803fd164 00000000 00000000 00000000 00000000 [ 2.810000] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.810000] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 d11dcae8 af8ddec5 [ 2.810000] [<80331004>] (netif_napi_del) from [<80292b30>] (ftgmac100_probe+0x290/0x674) [ 2.810000] [<80292b30>] (ftgmac100_probe) from [<80243df8>] (platform_drv_probe+0x60/0xc0) [ 2.810000] [<80243df8>] (platform_drv_probe) from [<80242178>] (driver_probe_device+0x280/0x44c) [ 2.810000] [<80242178>] (driver_probe_device) from [<80242434>] (__driver_attach+0xf0/0x104) [ 2.810000] [<80242434>] (__driver_attach) from [<80240148>] (bus_for_each_dev+0x7c/0xb0) [ 2.810000] [<80240148>] (bus_for_each_dev) from [<802425dc>] (driver_attach+0x28/0x30) [ 2.810000] [<802425dc>] (driver_attach) from [<80240ba8>] (bus_add_driver+0x14c/0x268) [ 2.810000] [<80240ba8>] (bus_add_driver) from [<80243068>] (driver_register+0x88/0x104) [ 2.810000] [<80243068>] (driver_register) from [<80244a38>] (__platform_driver_register+0x40/0x54) [ 2.810000] [<80244a38>] (__platform_driver_register) from [<805ab264>] (ftgmac100_driver_init+0x18/0x20) [ 2.810000] [<805ab264>] (ftgmac100_driver_init) from [<8058ae70>] (do_one_initcall+0xac/0x168) [ 2.810000] [<8058ae70>] (do_one_initcall) from [<8058b040>] (kernel_init_freeable+0x114/0x1cc) [ 2.810000] [<8058b040>] (kernel_init_freeable) from [<803fd170>] (kernel_init+0x18/0x104) [ 2.810000] [<803fd170>] (kernel_init) from [<8000a5e8>] (ret_from_fork+0x14/0x2c) [ 2.810000] Code: e594205c e5941058 e2843058 e3a05000 (e5812004) [ 3.210000] ---[ end trace f32811052fd3860c ]--- Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ftgmac100: Support NCSI VLAN filtering when availableSamuel Mendoza-Jonas2017-08-281-0/+5
|/ | | | | | | | | | | Register the ndo_vlan_rx_{add,kill}_vid callbacks and set the NETIF_F_HW_VLAN_CTAG_FILTER if NCSI is available. This allows the VLAN core to notify the NCSI driver when changes occur so that the remote NCSI channel can be properly configured to filter on the set VLAN tags. Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: return error in ftgmac100_alloc_rx_bufJoel Stanley2017-07-251-2/+2
| | | | | | | | | | | | | | | | | | | | The error paths set err, but it's not returned. I wondered if we should fix all of the callers to check the returned value, but Ben explains why the code is this way: > Most call sites ignore it on purpose. There's nothing we can do if > we fail to get a buffer at interrupt time, so we point the buffer to > the scratch page so the HW doesn't DMA into lalaland and lose the > packet. > > The one call site that tests and can fail is the one used when brining > the interface up. If we fail to allocate at that point, we fail the > ifup. But as you noticed, I do have a bug not returning the error. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Make the MDIO bus a child of the ethernet deviceBenjamin Herrenschmidt2017-07-241-0/+1
| | | | | | | | | | Populate mii_bus->parent with our own platform device before registering, which makes it easier to locate the MDIO bus in sysfs when trying to diagnose problems. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Joel Stanley <joel@jms.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Increase reset timeoutBenjamin Herrenschmidt2017-07-241-1/+1
| | | | | | | | | | | We had reports of 50us not being sufficient to reset the MAC, thus hitting the "Hardware reset failed" error bringing the interface up on some AST2400 based machines. This bumps the timeout to 200us. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Fix potential ordering issue in NAPI pollBenjamin Herrenschmidt2017-04-181-0/+7
| | | | | | | | | | | | | We need to ensure the loads from the descriptor are done after the MMIO store clearing the interrupts has completed, otherwise we might still miss work. A read back from the MMIO register will "push" the posted store and ioread32 has a barrier on weakly aordered architectures that will order subsequent accesses. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Display the discovered PHY device infoBenjamin Herrenschmidt2017-04-181-0/+3
| | | | | Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Allow configuration of phy interface via device-treeBenjamin Herrenschmidt2017-04-181-3/+39
| | | | | | | This uses the standard phy-mode property Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Add netpoll supportBenjamin Herrenschmidt2017-04-181-0/+14
| | | | | | | Just call the interrupt handler with interrupts locally disabled Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ftgmac100: Add vlan HW offloadBenjamin Herrenschmidt2017-04-181-1/+45
| | | | | | | | The chip supports HW vlan tag insertion and extraction. Add support for it. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2025-02-19 15:49:28 +0000