summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/mellanox
Commit message (Collapse)AuthorAgeFilesLines
* mlxsw: spectrum_ethtool: Remove internal speeds from PTYS registerDanielle Ratson2020-08-243-68/+1
| | | | | | | | | | | | | | | | | | | The PTYS register is used to report and configure the port type and speed. Currently, internal bits in the register are used the same way other bits are used. Using the internal bits can cause bad parameter firmware errors. For example, trying to write to internal bit 25 returns: EMAD reg access failed (tid=53e2bffa00004310,reg_id=5004(ptys),type=write,status=7(bad parameter)) Remove the internal bits from the PTYS register, so that it is no longer possible to pass them to firmware. Signed-off-by: Danielle Ratson <danieller@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: spectrum_trap: Adjust default policer burst size for Spectrum-{2, 3}Ido Schimmel2020-08-241-11/+11
| | | | | | | | | | | | | | On the Spectrum-{2,3} ASICs the minimum burst size of the packet trap policers needs to be 40% of the configured rate. Otherwise, intermittent drops are observed even when the incoming packet rate is slightly lower than the configured policer rate. Adjust the burst size of the registered packet trap policers so that they do not violate above mentioned limitation. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: spectrum_ptp: Use generic helper functionKurt Kanzenbach2020-08-191-25/+7
| | | | | | | | | | In order to reduce code duplication between ptp drivers, generic helper functions were introduced. Use them. Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-and-tested-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'thermal-v5.9-rc1' of ↵Linus Torvalds2020-08-061-74/+17
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux Pull thermal updates from Daniel Lezcano: - Add support to enable/disable the thermal zones resulting on core code and drivers cleanup (Andrzej Pietrasiewicz) - Add generic netlink support for userspace notifications: events, temperature and discovery commands (Daniel Lezcano) - Fix redundant initialization for a ret variable (Colin Ian King) - Remove the clock cooling code as it is used nowhere (Amit Kucheria) - Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian Rotariu) - Replace all references to thermal.txt in the documentation to the corresponding yaml files (Amit Kucheria) - Add maintainer entry for the IPA (Lukasz Luba) - Add support for MSM8939 for the tsens (Shawn Guo) - Update power allocator and devfreq cooling to SPDX licensing (Lukasz Luba) - Add Cannon Lake Low Power PCH support (Sumeet Pawnikar) - Add tsensor support for V2 mediatek thermal system (Henry Yen) - Fix thermal zone lookup by ID for the core code (Thierry Reding) * tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits) thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support thermal: mediatek: Add tsensor support for V2 thermal system thermal: mediatek: Prepare to add support for other platforms thermal: Update power allocator and devfreq cooling to SPDX licensing MAINTAINERS: update entry to thermal governors file name prefixing thermal: core: Add thermal zone enable/disable notification thermal: qcom: tsens-v0_1: Add support for MSM8939 dt-bindings: tsens: qcom: Document MSM8939 compatible thermal: core: Fix thermal zone lookup by ID thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id thermal: imx8mm: Support module autoloading thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor() MAINTAINERS: Add maintenance information for IPA thermal: rcar_gen3_thermal: Do not shadow thcode variable dt-bindings: thermal: Get rid of thermal.txt and replace references thermal: core: Move initialization after core initcall thermal: netlink: Improve the initcall ordering net: genetlink: Move initialization to core_initcall thermal: rcar_gen3_thermal: Add r8a774e1 support thermal/drivers/clock_cooling: Remove clock_cooling code ...
| * thermal: Simplify or eliminate unnecessary set_mode() methodsAndrzej Pietrasiewicz2020-06-291-30/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Setting polling_delay is now done at thermal_core level (by not polling DISABLED devices), so no need to repeat this code. int340x: Checking for an impossible enum value is unnecessary. acpi/thermal: It only prints debug messages. Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-11-andrzej.p@collabora.com
| * thermal: Use mode helpers in driversAndrzej Pietrasiewicz2020-06-291-20/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled(). Consequently, all set_mode() implementations in drivers: - can stop modifying tzd's "mode" member, - shall stop taking tzd's lock, as it is taken in the helpers - shall stop calling thermal_zone_device_update() as it is called in the helpers - can assume they are called when the mode truly changes, so checks to verify that can be dropped Not providing set_mode() by a driver no longer prevents the core from being able to set tzd's mode, so the relevant check in mode_store() is removed. Other comments: - acpi/thermal.c: tz->thermal_zone->mode will be updated only after we return from set_mode(), so use function parameter in thermal_set_mode() instead, no need to call acpi_thermal_check() in set_mode() - thermal/imx_thermal.c: regmap writes and mode assignment are done in thermal_zone_device_{en|dis}able() and set_mode() callback - thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a part of set_mode() callback, so they don't need to modify tzd->mode, and don't need to fall back to the opposite mode if unsuccessful, as the return value will be propagated to thermal_zone_device_{en|dis}able() and ultimately tzd's member will not be changed in thermal_zone_device_set_mode(). - thermal/of-thermal.c: no need to set zone->mode to DISABLED in of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
| * thermal: remove get_mode() operation of driversAndrzej Pietrasiewicz2020-06-291-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | get_mode() is now redundant, as the state is stored in struct thermal_zone_device. Consequently the "mode" attribute in sysfs can always be visible, because it is always possible to get the mode from struct tzd. Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-6-andrzej.p@collabora.com
| * thermal: Store device mode in struct thermal_zone_deviceAndrzej Pietrasiewicz2020-06-291-13/+8
| | | | | | | | | | | | | | | | | | | | | | | | Prepare for eliminating get_mode(). Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> [for acerhdf] Acked-by: Peter Kaestle <peter@piie.net> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200629122925.21729-5-andrzej.p@collabora.com
* | Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdmaLinus Torvalds2020-08-064-2/+20
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull rdma updates from Jason Gunthorpe: "A quiet cycle after the larger 5.8 effort. Substantially cleanup and driver work with a few smaller features this time. - Driver updates for hfi1, rxe, mlx5, hns, qedr, usnic, bnxt_re - Removal of dead or redundant code across the drivers - RAW resource tracker dumps to include a device specific data blob for device objects to aide device debugging - Further advance the IOCTL interface, remove the ability to turn it off. Add QUERY_CONTEXT, QUERY_MR, and QUERY_PD commands - Remove stubs related to devices with no pkey table - A shared CQ scheme to allow multiple ULPs to share the CQ rings of a device to give higher performance - Several more static checker, syzkaller and rare crashers fixed" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (121 commits) RDMA/mlx5: Fix flow destination setting for RDMA TX flow table RDMA/rxe: Remove pkey table RDMA/umem: Add a schedule point in ib_umem_get() RDMA/hns: Fix the unneeded process when getting a general type of CQE error RDMA/hns: Fix error during modify qp RTS2RTS RDMA/hns: Delete unnecessary memset when allocating VF resource RDMA/hns: Remove redundant parameters in set_rc_wqe() RDMA/hns: Remove support for HIP08_A RDMA/hns: Refactor hns_roce_v2_set_hem() RDMA/hns: Remove redundant hardware opcode definitions RDMA/netlink: Remove CAP_NET_RAW check when dump a raw QP RDMA/include: Replace license text with SPDX tags RDMA/rtrs: remove WQ_MEM_RECLAIM for rtrs_wq RDMA/rtrs-clt: add an additional random 8 seconds before reconnecting RDMA/cma: Execute rdma_cm destruction from a handler properly RDMA/cma: Remove unneeded locking for req paths RDMA/cma: Using the standard locking pattern when delivering the removal event RDMA/cma: Simplify DEVICE_REMOVAL for internal_id RDMA/efa: Add EFA 0xefa1 PCI ID RDMA/efa: User/kernel compatibility handshake mechanism ...
| * | net/mlx5: Enable count action for rules with allow actionMichael Guralnik2020-07-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | Enable the creation of rules with allow and count actions. This enables using counters on egress flow tables. Signed-off-by: Michael Guralnik <michaelgur@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | net/mlx5: Support setting access rights of dma addressesEli Cohen2020-07-151-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mlx5_fill_page_frag_array() is used to populate dma addresses to resources that require it, such as QPs, RQs etc. When the resource is used, PA list permissions are ignored. For resources that use MTT list, the user is required to provide the access rights. Subsequent patches use resources that require MTT lists, so modify API and implementation to support that. Signed-off-by: Eli Cohen <eli@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | net/mlx5: Enable QP number request when creating IPoIB underlay QPMichael Guralnik2020-07-032-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If in the process of creating the underlay QP for an IPoIB interface the user has set the address and specifically the 1st-3rd bytes representing the QP number, use the requested QP number when creating the underlay QP. For a user to be able to request a QP number on QP creation, the MKEY_BY_NAME NVCONFIG should be set. As mkey_by_name and qp_by_name are coupled in FW. This requires driver to query the mkey_by_name max cap during initialization and set the current cap if it was enabled in FW. Signed-off-by: Michael Guralnik <michaelgur@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
* | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds2020-08-05129-3555/+9642
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan. 2) Support UDP segmentation in code TSO code, from Eric Dumazet. 3) Allow flashing different flash images in cxgb4 driver, from Vishal Kulkarni. 4) Add drop frames counter and flow status to tc flower offloading, from Po Liu. 5) Support n-tuple filters in cxgb4, from Vishal Kulkarni. 6) Various new indirect call avoidance, from Eric Dumazet and Brian Vazquez. 7) Fix BPF verifier failures on 32-bit pointer arithmetic, from Yonghong Song. 8) Support querying and setting hardware address of a port function via devlink, use this in mlx5, from Parav Pandit. 9) Support hw ipsec offload on bonding slaves, from Jarod Wilson. 10) Switch qca8k driver over to phylink, from Jonathan McDowell. 11) In bpftool, show list of processes holding BPF FD references to maps, programs, links, and btf objects. From Andrii Nakryiko. 12) Several conversions over to generic power management, from Vaibhav Gupta. 13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry Yakunin. 14) Various https url conversions, from Alexander A. Klimov. 15) Timestamping and PHC support for mscc PHY driver, from Antoine Tenart. 16) Support bpf iterating over tcp and udp sockets, from Yonghong Song. 17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov. 18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan. 19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several drivers. From Luc Van Oostenryck. 20) XDP support for xen-netfront, from Denis Kirjanov. 21) Support receive buffer autotuning in MPTCP, from Florian Westphal. 22) Support EF100 chip in sfc driver, from Edward Cree. 23) Add XDP support to mvpp2 driver, from Matteo Croce. 24) Support MPTCP in sock_diag, from Paolo Abeni. 25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic infrastructure, from Jakub Kicinski. 26) Several pci_ --> dma_ API conversions, from Christophe JAILLET. 27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel. 28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki. 29) Refactor a lot of networking socket option handling code in order to avoid set_fs() calls, from Christoph Hellwig. 30) Add rfc4884 support to icmp code, from Willem de Bruijn. 31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei. 32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin. 33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin. 34) Support TCP syncookies in MPTCP, from Flowian Westphal. 35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano Brivio. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits) net: thunderx: initialize VF's mailbox mutex before first usage usb: hso: remove bogus check for EINPROGRESS usb: hso: no complaint about kmalloc failure hso: fix bailout in error case of probe ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM selftests/net: relax cpu affinity requirement in msg_zerocopy test mptcp: be careful on subflow creation selftests: rtnetlink: make kci_test_encap() return sub-test result selftests: rtnetlink: correct the final return value for the test net: dsa: sja1105: use detected device id instead of DT one on mismatch tipc: set ub->ifindex for local ipv6 address ipv6: add ipv6_dev_find() net: openvswitch: silence suspicious RCU usage warning Revert "vxlan: fix tos value before xmit" ptp: only allow phase values lower than 1 period farsync: switch from 'pci_' to 'dma_' API wan: wanxl: switch from 'pci_' to 'dma_' API hv_netvsc: do not use VF device if link is down dpaa2-eth: Fix passing zero to 'PTR_ERR' warning net: macb: Properly handle phylink on at91sam9x ...
| * \ \ Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller2020-08-032-42/+0
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Daniel Borkmann says: ==================== pull-request: bpf-next 2020-08-04 The following pull-request contains BPF updates for your *net-next* tree. We've added 73 non-merge commits during the last 9 day(s) which contain a total of 135 files changed, 4603 insertions(+), 1013 deletions(-). The main changes are: 1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko. 2) Add BPF iterator for map elements and to iterate all BPF programs for efficient in-kernel inspection, from Yonghong Song and Alexei Starovoitov. 3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid unwinder errors, from Song Liu. 4) Allow cgroup local storage map to be shared between programs on the same cgroup. Also extend BPF selftests with coverage, from YiFei Zhu. 5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM load instructions, from Jean-Philippe Brucker. 6) Follow-up fixes on BPF socket lookup in combination with reuseport group handling. Also add related BPF selftests, from Jakub Sitnicki. 7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for socket create/release as well as bind functions, from Stanislav Fomichev. 8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct xdp_statistics, from Peilin Ye. 9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime. 10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6} fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin. 11) Fix a bpftool segfault due to missing program type name and make it more robust to prevent them in future gaps, from Quentin Monnet. 12) Consolidate cgroup helper functions across selftests and fix a v6 localhost resolver issue, from John Fastabend. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | bpf, xdp: Remove XDP_QUERY_PROG and XDP_QUERY_PROG_HW XDP commandsAndrii Nakryiko2020-07-252-42/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that BPF program/link management is centralized in generic net_device code, kernel code never queries program id from drivers, so XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary. This patch removes all the implementations of those commands in kernel, along the xdp_attachment_query(). This patch was compile-tested on allyesconfig. Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
| * | | | Merge tag 'mlx5-updates-2020-08-03' of ↵David S. Miller2020-08-037-163/+112
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2020-08-03 This patchset introduces some updates to mlx5 driver. 1) Jakub converts mlx5 to use the new udp tunnel infrastructure. Starting with a hack to allow drivers to request a static configuration of the default vxlan port, and then a patch that converts mlx5. 2) Parav implements change_carrier ndo for VF eswitch representors, to speedup link state control of representors netdevices. 3) Alex Vesker, makes a simple update to software steering to fix an issue with push vlan action sequence 4) Leon removes a redundant dump stack on error flow. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| | * | | | net/mlx5: Delete extra dump stack that gives nothingLeon Romanovsky2020-08-031-6/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The WARN_*() macros are intended to catch impossible situations from the SW point of view. They gave a little in case HW<->SW interface is out-of-sync. Such out-of-sync scenario can be due to SW errors that are not part of this flow or because some HW errors, where dump stack won't help either. This specific WARN_ON() is useless because mlx5_core code is prepared to handle such situations and will unfold everything correctly while providing enough information to the users to understand why FS is not working. WARNING: CPU: 0 PID: 3222 at drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:825 connect_fts_in_prio.isra.20+0x1dd/0x260 linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:825 Kernel panic - not syncing: panic_on_warn set ... CPU: 0 PID: 3222 Comm: syz-executor861 Not tainted 5.5.0-rc6+ #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 Call Trace: __dump_stack linux/lib/dump_stack.c:77 [inline] dump_stack+0x94/0xce linux/lib/dump_stack.c:118 panic+0x234/0x56f linux/kernel/panic.c:221 __warn+0x1cc/0x1e1 linux/kernel/panic.c:582 report_bug+0x200/0x310 linux/lib/bug.c:195 fixup_bug.part.11+0x32/0x80 linux/arch/x86/kernel/traps.c:174 fixup_bug linux/arch/x86/kernel/traps.c:273 [inline] do_error_trap+0xd3/0x100 linux/arch/x86/kernel/traps.c:267 do_invalid_op+0x31/0x40 linux/arch/x86/kernel/traps.c:286 invalid_op+0x1e/0x30 linux/arch/x86/entry/entry_64.S:1027 RIP: 0010:connect_fts_in_prio.isra.20+0x1dd/0x260 linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:825 Code: 00 00 48 c7 c2 60 8c 31 84 48 c7 c6 00 81 31 84 48 8b 38 e8 3c a8 cb ff 41 83 fd 01 8b 04 24 0f 8e 29 ff ff ff e8 83 7b bc fe <0f> 0b 8b 04 24 e9 1a ff ff ff 89 04 24 e8 c1 20 e0 fe 8b 04 24 eb RSP: 0018:ffffc90004bb7858 EFLAGS: 00010293 RAX: ffff88805de98e80 RBX: 0000000000000c96 RCX: ffffffff827a853d RDX: 0000000000000000 RSI: 0000000000000000 RDI: fffff52000976efa RBP: 0000000000000007 R08: ffffed100da060e3 R09: ffffed100da060e3 R10: 0000000000000001 R11: ffffed100da060e2 R12: dffffc0000000000 R13: 0000000000000002 R14: ffff8880683a1a10 R15: ffffed100d07bc1c connect_prev_fts linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:844 [inline] connect_flow_table linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:975 [inline] __mlx5_create_flow_table+0x8f8/0x1710 linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:1064 mlx5_create_flow_table linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:1094 [inline] mlx5_create_auto_grouped_flow_table+0xe1/0x210 linux/drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:1136 _get_prio linux/drivers/infiniband/hw/mlx5/main.c:3286 [inline] get_flow_table+0x2ea/0x760 linux/drivers/infiniband/hw/mlx5/main.c:3376 mlx5_ib_create_flow+0x331/0x11c0 linux/drivers/infiniband/hw/mlx5/main.c:3896 ib_uverbs_ex_create_flow+0x13e8/0x1b40 linux/drivers/infiniband/core/uverbs_cmd.c:3311 ib_uverbs_write+0xaa5/0xdf0 linux/drivers/infiniband/core/uverbs_main.c:769 __vfs_write+0x7c/0x100 linux/fs/read_write.c:494 vfs_write+0x168/0x4a0 linux/fs/read_write.c:558 ksys_write+0xc8/0x200 linux/fs/read_write.c:611 do_syscall_64+0x9c/0x390 linux/arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x45a059 Code: 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fcc17564c98 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 00007fcc17564ca0 RCX: 000000000045a059 RDX: 0000000000000030 RSI: 00000000200003c0 RDI: 0000000000000005 RBP: 0000000000000007 R08: 0000000000000002 R09: 0000000000003131 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000006e636c R13: 0000000000000000 R14: 00000000006e6360 R15: 00007ffdcbdaf6a0 Dumping ftrace buffer: (ftrace buffer empty) Kernel Offset: disabled Rebooting in 1 seconds.. Fixes: f90edfd279f3 ("net/mlx5_core: Connect flow tables") Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
| | * | | | net/mlx5: convert to new udp_tunnel infrastructureJakub Kicinski2020-08-035-136/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allocate nic_info dynamically - n_entries is not constant. Attach the tunnel offload info only to the uplink representor. We expect the "main" netdev to be unregistered in switchdev mode, and there to be only one uplink representor. Drop the udp_tunnel_drop_rx_info() call, it was not there until commit b3c2ed21c0bd ("net/mlx5e: Fix VXLAN configuration restore after function reload") so the device doesn't need it, and core should handle reloads and reset just fine. v2: - don't drop the ndos on reprs, and register info on uplink repr. v4: - Move netdev tunnel structure handling to en_main.c Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| | * | | | net/mlx5: DR, Change push vlan action sequenceAlex Vesker2020-08-031-21/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DR TX state machine supports the following order: modify header, push vlan and encapsulation. Instead fs_dr would pass: push vlan, modify header and encapsulation. The above caused the rule creation to fail on invalid action sequence provided error. Fixes: 6a48faeeca10 ("net/mlx5: Add direct rule fs_cmd implementation") Signed-off-by: Alex Vesker <valex@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| | * | | | net/mlx5e: Enable users to change VF/PF representors carrier stateParav Pandit2020-08-031-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently PF and VF representor netdevice carrier is always controlled by controlling the representor netdevice device state as up/down. Representor netdevice state change undergoes one or more txq/rxq destroy/create commands to firmware, skb and its rx buffer allocation, health reporters creation and more. Due to this limitation users do not have the ability to just change the carrier of the non uplink representors without modifying the device state. In one use case when the eswitch physical port carrier is down/up, user needs to update the VF link state to same as physical port carrier. Example of updating VF representor carrier state: $ ip link set enp0s8f0npf0vf0 carrier off $ ip link set enp0s8f0npf0vf0 carrier on This enhancement results into VF link state change which is represented by the VF representor netdevice carrier. This enables users to modify the representor carrier without modifying the representor netdevice state. A simple test is run using [1] to calculate the time difference between updating carrier vs updating device state (to update just the carrier) with one VF to simulate 255 VFs. Time taken to update the carrier using device up/down: $ time ./calculate.sh dev enp0s8f0npf0vf0 real 0m30.913s user 0m0.200s sys 0m11.168s Time taken to update just the carrier using carrier iproute2 command: $ time ./calculate.sh carrier enp0s8f0npf0vf0 real 0m2.142s user 0m0.160s sys 0m2.021s Test shows that its better to use carrier on/off user interface to notify link up/down event to VF compare to device up/down interface, because carrier user interface delivers the same event 15 times faster. [1] https://github.com/paravmellanox/myscripts/blob/master/calculate_carrier_time.sh Signed-off-by: Parav Pandit <parav@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | mlxsw: spectrum_qdisc: Offload action trap for qeventsPetr Machata2020-08-033-13/+95
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When offloading action trap on a qevent, pass to_dev of NULL to the SPAN module to trigger the mirror to the CPU port. Query the buffer drops policer and use it for policing of the trapped traffic. Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | mlxsw: spectrum_trap: Add early_drop trapIdo Schimmel2020-08-033-3/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As previously explained, packets that are dropped due to buffer related reasons (e.g., tail drop, early drop) can be mirrored to the CPU port. These packets are then trapped with one of the "mirror session" traps and their CQE includes the reason for which the packet was mirrored. Register with devlink a new trap, early_drop, and initialize the corresponding Rx listener with the appropriate mirror reason. Return an error in case user tries to change the traps' action, as this is not supported. Since Spectrum-1 does not support these traps, the above is only done for Spectrum-2 onwards. Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | mlxsw: spectrum_trap: Allow for per-ASIC traps initializationIdo Schimmel2020-08-032-9/+75
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Subsequent patches will need to register different traps for Spectrum-1 and Spectrum-2 onwards. Enable that by invoking a per-ASIC operation during traps initialization. Reviewed-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | mlxsw: spectrum_trap: Allow for per-ASIC trap groups initializationIdo Schimmel2020-08-034-9/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Subsequent patches will need to register different trap groups for Spectrum-1 and Spectrum-2 onwards. Enable that by invoking a per-ASIC operation during trap groups initialization. Reviewed-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | mlxsw: spectrum_span: On policer_id_base_ref_count, use dec_and_testPetr Machata2020-08-031-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When unsetting policer base, the SPAN code currently uses refcount_dec(). However that function splats when the counter reaches zero, because reaching zero without actually testing is in general indicative of a missing cleanup. There is no cleanup to be done here, but nonetheless, use refcount_dec_and_test() as required. Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | mlxsw: spectrum_trap: Use 'size_t' for array sizesIdo Schimmel2020-08-032-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use 'size_t' instead of 'u64' for array sizes, as this this is correct type to use for expressions involving sizeof(). Suggested-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | devlink: Pass extack when setting trap's action and group's parametersIdo Schimmel2020-08-034-13/+22
| |/ / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A later patch will refuse to set the action of certain traps in mlxsw and also to change the policer binding of certain groups. Pass extack so that failure could be communicated clearly to user space. Reviewed-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2020-08-0218-109/+207
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Resolved kernel/bpf/btf.c using instructions from merge commit 69138b34a7248d2396ab85c8652e20c0c39beaba Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | mlxsw: spectrum_cnt: Use flex_array_size() helper in memcpy()Gustavo A. R. Silva2020-07-301-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make use of the flex_array_size() helper to calculate the size of a flexible array member within an enclosing structure. This helper offers defense-in-depth against potential integer overflows, while at the same time makes it explicitly clear that we are dealing witha flexible array member. Also, remove unnecessary pointer identifier sub_pool. Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Tested-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | mlxsw: core: Add support for temperature thresholds reading for QSFP-DD ↵Vadim Pasternak2020-07-282-10/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | transceivers Allow QSFP-DD transceivers temperature thresholds reading for hardware monitoring and thermal control. For this type, the thresholds are located in page 02h according to the "Module and Lane Thresholds" description from Common Management Interface Specification. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | mlxsw: core: Add ethtool support for QSFP-DD transceiversVadim Pasternak2020-07-282-2/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Quad Small Form Factor Pluggable Double Density (QSFP-DD) hardware specification defines a form factor that supports up to 400 Gbps in aggregate over an 8x50-Gbps electrical interface. The QSFP-DD supports both optical and copper interfaces. Implementation is based on Common Management Interface Specification; Rev 4.0 May 8, 2019. Table 8-2 "Identifier and Status Summary (Lower Page)" from this spec defines "Id and Status" fields located at offsets 00h - 02h. Bit 2 at offset 02h ("Flat_mem") specifies QSFP EEPROM memory mode, which could be "upper memory flat" or "paged". Flat memory mode is coded "1", and indicates that only page 00h is implemented in EEPROM. Paged memory is coded "0" and indicates that pages 00h, 01h, 02h, 10h and 11h are implemented. Pages 10h and 11h are currently not supported by the driver. "Flat" memory mode is used for the passive copper transceivers. For this type only page 00h (256 bytes) is available. "Paged" memory is used for the optical transceivers. For this type pages 00h (256 bytes), 01h (128 bytes) and 02h (128 bytes) are available. Upper page 01h contains static advertising field, while upper page 02h contains the module-defined thresholds and lane-specific monitors. Extend enumerator 'mlxsw_reg_mcia_eeprom_module_info_id' with additional field 'MLXSW_REG_MCIA_EEPROM_MODULE_INFO_TYPE_ID'. This field is used to indicate for QSFP-DD transceiver type which memory mode is to be used. Expose 256 bytes buffer for QSFP-DD passive copper transceiver and 512 bytes buffer for optical. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net/mlx5: drop unnecessary list_emptyJulia Lawall2020-07-282-10/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | list_for_each_entry is able to handle an empty list. The only effect of avoiding the loop is not initializing the index variable. Drop list_empty tests in cases where these variables are not used. Note that list_for_each_entry is defined in terms of list_first_entry, which indicates that it should not be used on an empty list. But in list_for_each_entry, the element obtained by list_first_entry is not really accessed, only the address of its list_head field is compared to the address of the list head, so the list_first_entry is safe. The semantic patch that makes this change is as follows (with another variant for the no brace case): (http://coccinelle.lip6.fr/) <smpl> @@ expression x,e; iterator name list_for_each_entry; statement S; identifier i; @@ -if (!(list_empty(x))) { list_for_each_entry(i,x,...) S - } ... when != i ? i = e </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5: Use fallthrough pseudo-keywordGustavo A. R. Silva2020-07-288-13/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5: DR, Reduce print level for matcher printAlex Vesker2020-07-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is no need to print on each unsuccessful matcher ip_version combination since it probably will happen when trying to create all the possible combinations. On a real failure we have a print in the calling function. Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5e: Add support for PCI relaxed orderingAya Levin2020-07-283-2/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The concept of Relaxed Ordering in the PCI Express environment allows switches in the path between the Requester and Completer to reorder some transactions just received before others that were previously enqueued. In ETH driver, there is no question of write integrity since each memory segment is written only once per cycle. In addition, the driver doesn't access the memory shared with the hardware until the corresponding CQE arrives indicating all PCI transactions are done. Running TCP single stream over ConnectX-4 LX, ARM CPU on remote-numa has 300% improvement in the bandwidth. With relaxed ordering turned off: BW:10 [GB/s] With relaxed ordering turned on: BW:40 [GB/s] The driver turns relaxed ordering with respect to the firmware capabilities and the return value from pcie_relaxed_ordering_enabled(). Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5e: Use indirect call wrappers for RX post WQEs functionsTariq Toukan2020-07-285-8/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the indirect call wrapper API macros for declaration and scope of the RX post WQEs functions. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5e: Move exposure of datapath function to txrx headerTariq Toukan2020-07-284-23/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move them from the generic header file "en.h", to the datapath header file "txrx.h". Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5e: RX, Re-work initializaiton of RX function pointersTariq Toukan2020-07-289-96/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Instead of exposing the RQ datapath handlers (from en_rx.c) so that they are set in the control path (in en_main.c), wrap this logic in a single function in en_rx.c and expose it alone. Every profile will now have a pointer to the new mlx5e_rx_handlers structure, instead of directly pointing to the previously-exposed RQ handlers. This significantly improves locality and modularity of the driver, and allows many functions in en_rx.c to become static. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5e: Link non uplink representors to PCI deviceParav Pandit2020-07-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently PF and VF representors are exposed as virtual device. They are not linked to its parent PCI device like how uplink representor is linked. Due to this, PF and VF representors cannot benefit of the systemd defined naming scheme. This requires special handling by the users. Hence, link the PF and VF representors to their parent PCI device similar to existing uplink representor netdevice. Example: udevadm output before linking to PCI device: $ udevadm test-builtin net_id /sys/class/net/eth6 Load module index Network interface NamePolicy= disabled on kernel command line, ignoring. Parsed configuration file /usr/lib/systemd/network/99-default.link Created link configuration context. Using default interface naming scheme 'v243'. ID_NET_NAMING_SCHEME=v243 Unload module index Unloaded link configuration context. udevadm output after linking to PCI device: $ udevadm test-builtin net_id /sys/class/net/eth6 Load module index Network interface NamePolicy= disabled on kernel command line, ignoring. Parsed configuration file /usr/lib/systemd/network/99-default.link Created link configuration context. Using default interface naming scheme 'v243'. ID_NET_NAMING_SCHEME=v243 ID_NET_NAME_PATH=enp0s8f0npf0vf0 Unload module index Unloaded link configuration context. In past there was little concern over seeing 10,000 lines output showing up at thread [1] is not applicable as ndo ops for VF handling is not exposed for all the 100 repesentors for mlx5 devices. Additionally alternative device naming [2] to overcome shorter device naming is also part of the latest systemd release v245. [1] https://marc.info/?l=linux-netdev&m=152657949117904&w=2 [2] https://lwn.net/Articles/814068/ Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5: E-switch, Use eswitch total_vportsParav Pandit2020-07-281-7/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently steering table and rx group initialization helper routines works on the total_vports passed as input parameter. Both eswitch helpers work on the mlx5_eswitch and thereby have access to esw->total_vports. Hence use it directly instead of passing it via function input arguments. Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Bodong Wang <bodong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5: E-switch, Reuse total_vports and avoid duplicate nvportsParav Pandit2020-07-282-8/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Total e-switch vports are already stored in mlx5_eswitch total_vports. Avoid copy of it in nvports and reuse existing total_vports calculation. Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Bodong Wang <bodong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5: E-switch, Consider maximum vf vports for steering initParav Pandit2020-07-281-7/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When eswitch is enabled, VFs might not be enabled. Hence, consider maximum number of VFs. This further closes the gap between handling VF vports between ECPF and PF. Fixes: ea2128fd632c ("net/mlx5: E-switch, Reduce dependency on num_vfs during mode set") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Bodong Wang <bodong@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5: Add function ID to reclaim pages debug logAvihu Hagag2020-07-281-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add function ID to reclaim pages debug log for better user visibility. Signed-off-by: Avihu Hagag <avihuh@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5: Hold pages RB tree per VFEran Ben Elisha2020-07-281-38/+104
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Per page request event, FW request to allocated or release pages for a single function. Driver maintains FW pages object per function, so there is no need to hold one global page data-base. Instead, have a page data-base per function, which will improve performance release flow in all cases, especially for "release all pages". As the range of function IDs is large and not sequential, use xarray to store a per function ID page data-base, where the function ID is the key. Upon first allocation of a page to a function ID, create the page data-base per function. This data-base will be released only at pagealloc mechanism cleanup. NIC: ConnectX-4 Lx CPU: Intel(R) Xeon(R) CPU E5-2650 v2 @ 2.60GHz Test case: 32 VFs, measure release pages on one VF as part of FLR Before: 0.021 Sec After: 0.014 Sec The improvement depends on amount of VFs and memory utilization by them. Time measurements above were taken from idle system. Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx4: Use fallthrough pseudo-keywordGustavo A. R. Silva2020-07-273-5/+5
| | |/ / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2020-07-252-17/+34
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The UDP reuseport conflict was a little bit tricky. The net-next code, via bpf-next, extracted the reuseport handling into a helper so that the BPF sk lookup code could invoke it. At the same time, the logic for reuseport handling of unconnected sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace which changed the logic to carry on the reuseport result into the rest of the lookup loop if we do not return immediately. This requires moving the reuseport_has_conns() logic into the callers. While we are here, get rid of inline directives as they do not belong in foo.c files. The other changes were cases of more straightforward overlapping modifications. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | | | net/mlx5e: CT: Map 128 bits labels to 32 bit map IDEli Britstein2020-07-163-23/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The 128 bits ct_label field is matched using a 32 bit hardware register. As such, only the lower 32 bits of ct_label field are offloaded. Change this logic to support setting and matching higher bits too. Map the 128 bits data to a unique 32 bits ID. Matching is done as exact match of the mapping ID of key & mask. Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Oz Shlomo <ozsh@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Maor Dickman <maord@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5e: Do not request completion on every single UMR WQETariq Toukan2020-07-161-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UMR WQEs are posted in bulks, and HW is notified once per a bulk. Reduce the number of completions by requesting such only for the last WQE of the bulk. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5e: RX, Avoid indirect call in representor CQE handlingTariq Toukan2020-07-161-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call when/if CONFIG_RETPOLINE=y. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * | | | | net/mlx5e: XDP, Avoid indirect call in TX flowTariq Toukan2020-07-163-14/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call when/if CONFIG_RETPOLINE=y. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-31 13:45:03 +0000