summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet
Commit message (Collapse)AuthorAgeFilesLines
* Merge branch '40GbE' of ↵David S. Miller2017-10-285-21/+22
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2017-10-26 This series contains fixes to e1000, igb, ixgbe and i40e. Vincenzo Maffione fixes a potential race condition which would result in the interface being up but transmits are disabled in the hardware. Colin Ian King fixes a possible NULL pointer dereference in e1000, which was found by Coverity. Jean-Philippe Brucker fixes a possible kernel panic when a driver cannot map a transmit buffer, which is caused by an erroneous test. Alex provides a fix for ixgbe, which is a partial revert of the commit ffed21bcee7a ("ixgbe: Don't bother clearing buffer memory for descriptor rings") because the previous commit messed up the exception handling path by adding the count back in when we did not need to. Also fixed a typo, where the transmit ITR setting was being used to determine if we were using adaptive receive interrupt moderation or not. Lastly, fixed a memory leak by including programming descriptors in the cleaned count. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * i40e: Add programming descriptors to cleaned_countAlexander Duyck2017-10-261-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch updates the i40e driver to include programming descriptors in the cleaned_count. Without this change it becomes possible for us to leak memory as we don't trigger a large enough allocation when the time comes to allocate new buffers and we end up overwriting a number of rx_buffers equal to the number of programming descriptors we encountered. Fixes: 0e626ff7ccbf ("i40e: Fix support for flow director programming status") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Anders K. Pedersen <akp@cohaesio.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * i40e: Fix incorrect use of tx_itr_setting when checking for Rx ITR setupAlexander Duyck2017-10-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | It looks like there was either a copy/paste error or just a typo that resulted in the Tx ITR setting being used to determine if we were using adaptive Rx interrupt moderation or not. This patch fixes the typo. Fixes: 65e87c0398f5 ("i40evf: support queue-specific settings for interrupt moderation") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * ixgbe: Fix Tx map failure pathAlexander Duyck2017-10-261-12/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is a partial revert of "ixgbe: Don't bother clearing buffer memory for descriptor rings". Specifically I messed up the exception handling path a bit and this resulted in us incorrectly adding the count back in when we didn't need to. In order to make this simpler I am reverting most of the exception handling path change and instead just replacing the bit that was handled by the unmap_and_free call. Fixes: ffed21bcee7a ("ixgbe: Don't bother clearing buffer memory for descriptor rings") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * igb: Fix TX map failure pathJean-Philippe Brucker2017-10-261-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the driver cannot map a TX buffer, instead of rolling back gracefully and retrying later, we currently get a panic: [ 159.885994] igb 0000:00:00.0: TX DMA map failed [ 159.886588] Unable to handle kernel paging request at virtual address ffff00000a08c7a8 ... [ 159.897031] PC is at igb_xmit_frame_ring+0x9c8/0xcb8 Fix the erroneous test that leads to this situation. Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * e1000: avoid null pointer dereference on invalid stat typeColin Ian King2017-10-261-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently if the stat type is invalid then data[i] is being set either by dereferencing a null pointer p, or it is reading from an incorrect previous location if we had a valid stat type previously. Fix this by skipping over the read of p on an invalid stat type. Detected by CoverityScan, CID#113385 ("Explicit null dereferenced") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * e1000: fix race condition between e1000_down() and e1000_watchdogVincenzo Maffione2017-10-261-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a race condition that can result into the interface being up and carrier on, but with transmits disabled in the hardware. The bug may show up by repeatedly IFF_DOWN+IFF_UP the interface, which allows e1000_watchdog() interleave with e1000_down(). CPU x CPU y -------------------------------------------------------------------- e1000_down(): netif_carrier_off() e1000_watchdog(): if (carrier == off) { netif_carrier_on(); enable_hw_transmit(); } disable_hw_transmit(); e1000_watchdog(): /* carrier on, do nothing */ Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | net: stmmac: First Queue must always be in DCB modeJose Abreu2017-10-271-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to DWMAC databook the first queue operating mode must always be in DCB. As MTL_QUEUE_DCB = 1, we need to always set the first queue operating mode to DCB otherwise driver will think that queue is in AVB mode (because MTL_QUEUE_AVB = 0). Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: stmmac: dwc-qos-eth: Fix typo in DT bindings parsingJose Abreu2017-10-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to DT bindings documentation we are expecting a property called "snps,read-requests" but we are parsing instead a property called "read,read-requests". This is clearly a typo. Fix it. Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge tag 'mlx5-fixes-2017-10-26' of ↵David S. Miller2017-10-275-96/+202
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2017-10-26 The series includes some misc fixes for mlx5 core and etherent driver. Please pull and let me know if there's any problem. For -Stable: net/mlx5e: Properly deal with encap flows add/del under neigh update (kernels >= 4.12) net/mlx5: Fix health work queue spin lock to IRQ safe (kernels >= 4.13) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/mlx5e: DCBNL, Implement tc with ets type and zero bandwidthHuy Nguyen2017-10-262-30/+104
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously, tc with ets type and zero bandwidth is not accepted by driver. This behavior does not follow the IEEE802.1qaz spec. If there are tcs with ets type and zero bandwidth, these tcs are assigned to the lowest priority tc_group #0. We equally distribute 100% bw of the tc_group #0 to these zero bandwidth ets tcs. Also, the non zero bandwidth ets tcs are assigned to tc_group #1. If there is no zero bandwidth ets tc, the non zero bandwidth ets tcs are assigned to tc_group #0. Fixes: cdcf11212b22 ("net/mlx5e: Validate BW weight values of ETS") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * net/mlx5e: Properly deal with encap flows add/del under neigh updateOr Gerlitz2017-10-261-35/+54
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, the encap action offload is handled in the actions parse function and not in mlx5e_tc_add_fdb_flow() where we deal with all the other aspects of offloading actions (vlan, modify header) and the rule itself. When the neigh update code (mlx5e_tc_encap_flows_add()) recreates the encap entry and offloads the related flows, we wrongly call again into mlx5e_tc_add_fdb_flow(), this for itself would cause us to handle again the offloading of vlans and header re-write which puts things in non consistent state and step on freed memory (e.g the modify header parse buffer which is already freed). Since on error, mlx5e_tc_add_fdb_flow() detaches and may release the encap entry, it causes a corruption at the neigh update code which goes over the list of flows associated with this encap entry, or double free when the tc flow is later deleted by user-space. When neigh update (mlx5e_tc_encap_flows_del()) unoffloads the flows related to an encap entry which is now invalid, we do a partial repeat of the eswitch flow removal code which is wrong too. To fix things up we do the following: (1) handle the encap action offload in the eswitch flow add function mlx5e_tc_add_fdb_flow() as done for the other actions and the rule itself. (2) modify the neigh update code (mlx5e_tc_encap_flows_add/del) to only deal with the encap entry and rules delete/add and not with any of the other offloaded actions. Fixes: 232c001398ae ('net/mlx5e: Add support to neighbour update flow') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * net/mlx5: Delay events till mlx5 interface's add complete for pci resumeHuy Nguyen2017-10-261-29/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mlx5_ib_add is called during mlx5_pci_resume after a pci error. Before mlx5_ib_add completes, there are multiple events which trigger function mlx5_ib_event. This cause kernel panic because mlx5_ib_event accesses unitialized resources. The fix is to extend Erez Shitrit's patch <97834eba7c19> ("net/mlx5: Delay events till ib registration ends") to cover the pci resume code path. Trace: mlx5_core 0001:01:00.6: mlx5_pci_resume was called mlx5_core 0001:01:00.6: firmware version: 16.20.1011 mlx5_core 0001:01:00.6: mlx5_attach_interface:164:(pid 779): mlx5_ib_event:2996:(pid 34777): warning: event on port 1 mlx5_ib_event:2996:(pid 34782): warning: event on port 1 Unable to handle kernel paging request for data at address 0x0001c104 Faulting instruction address: 0xd000000008f411fc Oops: Kernel access of bad area, sig: 11 [#1] ... ... Call Trace: [c000000fff77bb70] [d000000008f4119c] mlx5_ib_event+0x64/0x470 [mlx5_ib] (unreliable) [c000000fff77bc60] [d000000008e67130] mlx5_core_event+0xb8/0x210 [mlx5_core] [c000000fff77bd10] [d000000008e4bd00] mlx5_eq_int+0x528/0x860[mlx5_core] Fixes: 97834eba7c19 ("net/mlx5: Delay events till ib registration ends") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
| * net/mlx5: Fix health work queue spin lock to IRQ safeMoshe Shemesh2017-10-261-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | spin_lock/unlock of health->wq_lock should be IRQ safe. It was changed to spin_lock_irqsave since adding commit 0179720d6be2 ("net/mlx5: Introduce trigger_health_work function") which uses spin_lock from asynchronous event (IRQ) context. Thus, all spin_lock/unlock of health->wq_lock should have been moved to IRQ safe mode. However, one occurrence on new code using this lock missed that change, resulting in possible deadlock: kernel: Possible unsafe locking scenario: kernel: CPU0 kernel: ---- kernel: lock(&(&health->wq_lock)->rlock); kernel: <Interrupt> kernel: lock(&(&health->wq_lock)->rlock); kernel: #012 *** DEADLOCK *** Fixes: 2a0165a034ac ("net/mlx5: Cancel delayed recovery work when unloading the driver") Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
* | net: mvpp2: do not sleep in set_rx_modeAntoine Tenart2017-10-261-2/+2
| | | | | | | | | | | | | | | | | | This patch replaces GFP_KERNEL by GFP_ATOMIC to avoid sleeping in the ndo_set_rx_mode() call which is called with BH disabled. Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: mvpp2: fix invalid parameters order when calling the tcam initAntoine Tenart2017-10-261-2/+2
| | | | | | | | | | | | | | | | | | | | When calling mvpp2_prs_mac_multi_set() from mvpp2_prs_mac_init(), two parameters (the port index and the table index) are inverted. Fixes this. Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: mvpp2: fix typo in the tcam setupAntoine Tenart2017-10-261-1/+1
|/ | | | | | | | | This patch fixes a typo in the mvpp2_prs_tcam_data_cmp() function, as the shift value is inverted with the data. Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* nfp: refuse offloading filters that redirects to upper devicesPieter Jansen van Vuuren2017-10-261-0/+2
| | | | | | | | | | | | | | | Previously we did not ensure that a netdev is a representative netdev before dereferencing its private data. This can occur when an upper netdev is created on a representative netdev. This patch corrects this by first ensuring that the netdev is a representative netdev before using it. Checking only switchdev_port_same_parent_id is not sufficient to ensure that we can safely use the netdev. Failing to check that the netdev is also a representative netdev would result in incorrect dereferencing. Fixes: 1a1e586f54bf ("nfp: add basic action capabilities to flower offloads") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: mvpp2: do not call txq_done from the Tx path when Tx irqs are usedAntoine Tenart2017-10-241-1/+1
| | | | | | | | | | | | | | When Tx IRQs are used, txq_bufs_free() can be called from both the Tx path and from NAPI poll(). This led to CPU stalls as if these two tasks (Tx and Poll) are scheduled on two CPUs at the same time, DMA unmapping operations are done on the same txq buffers. This patch adds a check not to call txq_done() from the Tx path if Tx interrupts are used as it does not make sense to do so. Fixes: edc660fa09e2 ("net: mvpp2: replace TX coalescing interrupts with hrtimer") Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: mvpp2: do not unmap TSO headers buffersAntoine Tenart2017-10-241-4/+13
| | | | | | | | | | | | The TSO header buffers are coming from a per cpu pool and should not be unmapped as they are reused. The PPv2 driver was unmapping all descriptors buffers unconditionally. This patch fixes this by checking the buffers dma addresses before unmapping them, and by not unmapping those who are located in the TSO header pool. Fixes: 186cd4d4e414 ("net: mvpp2: software tso support") Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: mvpp2: fix TSO headers allocation and managementYan Markman2017-10-241-3/+3
| | | | | | | | | | | TSO headers are managed with txq index and therefore should be aligned with the txq size, not with the aggregated txq size. Fixes: 186cd4d4e414 ("net: mvpp2: software tso support") Reported-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Yan Markman <ymarkman@marvell.com> Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* stmmac: Don't access tx_q->dirty_tx before netif_tx_lockBernd Edlinger2017-10-221-1/+2
| | | | | | | | | | | | | | | | | | | | This is the possible reason for different hard to reproduce problems on my ARMv7-SMP test system. The symptoms are in recent kernels imprecise external aborts, and in older kernels various kinds of network stalls and unexpected page allocation failures. My testing indicates that the trouble started between v4.5 and v4.6 and prevails up to v4.14. Using the dirty_tx before acquiring the spin lock is clearly wrong and was first introduced with v4.6. Fixes: e3ad57c96715 ("stmmac: review RX/TX ring management") Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: stmmac: Prevent infinite loop in get_rx_timestamp_status()Jose Abreu2017-10-221-1/+1
| | | | | | | | | | | | Prevent infinite loop by correctly setting the loop condition to break when i == 10. Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: stmmac: Fix stmmac_get_rx_hwtstamp()Jose Abreu2017-10-221-7/+6
| | | | | | | | | | | | | | | When using GMAC4 the valid timestamp is from CTX next desc but we are passing the previous desc to get_rx_timestamp_status() callback. Fix this and while at it rework a little bit the function logic. Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: stmmac: Add missing call to dev_kfree_skb()Jose Abreu2017-10-221-0/+1
| | | | | | | | | | | | | | | When RX HW timestamp is enabled and a frame is discarded we are not freeing the skb but instead only setting to NULL the entry. Add a call to dev_kfree_skb_any() so that skb entry is correctly freed. Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: spectrum_router: Configure TIGCR on initPetr Machata2017-10-221-1/+10
| | | | | | | | | | | | Spectrum tunnels do not default to ttl of "inherit" like the Linux ones do. Configure TIGCR on router init so that the TTL of tunnel packets is copied from the overlay packets. Fixes: ee954d1a91b2 ("mlxsw: spectrum_router: Support GRE tunnels") Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: reg: Add Tunneling IPinIP General Configuration RegisterPetr Machata2017-10-221-0/+31
| | | | | | | | | | | The TIGCR register is used for setting up the IPinIP Tunnel configuration. Fixes: ee954d1a91b2 ("mlxsw: spectrum_router: Support GRE tunnels") Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: aquantia: Bad udp rate on default interrupt coalescingIgor Russkikh2017-10-211-6/+6
| | | | | | | | | | | | | | | | | Default Tx rates cause very long ISR delays on Tx. 0xff is 510us delay, giving only ~ 2000 interrupts per seconds for Tx rings cleanup. With these settings udp tx rate was never higher than ~800Mbps on a single stream. Changing min delay to 0xF makes it way better with ~6Gbps TCP stream performance is almost unaffected by this change, since LSO optimizations play important role. CPU load is affected insignificantly by this change. Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: aquantia: Enable coalescing management via ethtool interfaceIgor Russkikh2017-10-219-62/+155
| | | | | | | | | | | Aquantia NIC allows both TX and RX interrupt throttle rate (ITR) management, but this was used in a very limited way via predefined values. This patch allows to setup ITR default values via module command line arguments and via standard ethtool coalescing settings. Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: aquantia: mmio unmap was not performed on driver removalIgor Russkikh2017-10-211-0/+3
| | | | | | | | That may lead to mmio resource leakage. Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: aquantia: Limit number of MSIX irqs to the number of cpusIgor Russkikh2017-10-211-4/+7
| | | | | | | | | | There is no much practical use from having MSIX vectors more that number of cpus, thus cap this first with preconfigured limit, then with number of cpus online. Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: aquantia: Fixed transient link up/down/up notificationIgor Russkikh2017-10-211-0/+2
| | | | | | | | | | When doing ifconfig down/up, driver did not reported carrier_off neither in nic_stop nor in nic_start. That caused link to be visible as "up" during couple of seconds immediately after "ifconfig up". Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: aquantia: Add queue restarts stats counterIgor Russkikh2017-10-212-58/+37
| | | | | | | | | Queue stat strings are cleaned up, duplicate stat name strings removed, queue restarts counter added Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: aquantia: Reset nic statistics on interface up/downIgor Russkikh2017-10-216-17/+75
| | | | | | | | | | | | | | | | | Internal statistics system on chip never gets reset until hardware reboot. This is quite inconvenient in terms of ethtool statistics usage. This patch implements incremental statistics update inside of service callback. Upon nic initialization, first request is done to fetch initial stat data, current collected stat data gets cleared. Internal statistics mailbox readout is improved to save space and increase readability Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ena: fix wrong max Tx/Rx queues on ethtoolNetanel Belgazal2017-10-191-2/+2
| | | | | | | | | ethtool ena_get_channels() expose the max number of queues as the max number of queues ENA supports (128 queues) and not the actual number of created queues. Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ena: fix rare kernel crash when bar memory remap failsNetanel Belgazal2017-10-191-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This failure is rare and only found on testing where deliberately fail devm_ioremap() [ 451.170464] ena 0000:04:00.0: failed to remap regs bar 451.170549] Workqueue: pciehp-1 pciehp_power_thread [ 451.170551] task: ffff88085a5f2d00 task.stack: ffffc9000756c000 [ 451.170552] RIP: 0010:devm_iounmap+0x2d/0x40 [ 451.170553] RSP: 0018:ffffc9000756fac0 EFLAGS: 00010282 [ 451.170554] RAX: 00000000fffffffe RBX: 0000000000000000 RCX: 0000000000000000 [ 451.170555] RDX: ffffffff813a7e00 RSI: 0000000000000282 RDI: 0000000000000282 [ 451.170556] RBP: ffffc9000756fac8 R08: 00000000fffffffe R09: 00000000000009b7 [ 451.170557] R10: 0000000000000005 R11: 00000000000009b6 R12: ffff880856c9d0a0 [ 451.170558] R13: ffffc9000f5c90c0 R14: ffff880856c9d0a0 R15: 0000000000000028 [ 451.170559] FS: 0000000000000000(0000) GS:ffff88085f400000(0000) knlGS:0000000000000000 [ 451.170560] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 451.170561] CR2: 00007f169038b000 CR3: 0000000001c09000 CR4: 00000000003406f0 [ 451.170562] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 451.170562] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 451.170563] Call Trace: [ 451.170572] ena_release_bars.isra.48+0x34/0x60 [ena] [ 451.170574] ena_probe+0x144/0xd90 [ena] [ 451.170579] ? ida_simple_get+0x98/0x100 [ 451.170585] ? kernfs_next_descendant_post+0x40/0x50 [ 451.170591] local_pci_probe+0x45/0xa0 [ 451.170592] pci_device_probe+0x157/0x180 [ 451.170599] driver_probe_device+0x2a8/0x460 [ 451.170600] __device_attach_driver+0x7e/0xe0 [ 451.170602] ? driver_allows_async_probing+0x30/0x30 [ 451.170603] bus_for_each_drv+0x68/0xb0 [ 451.170605] __device_attach+0xdd/0x160 [ 451.170607] device_attach+0x10/0x20 [ 451.170610] pci_bus_add_device+0x4f/0xa0 [ 451.170611] pci_bus_add_devices+0x39/0x70 [ 451.170613] pciehp_configure_device+0x96/0x120 [ 451.170614] pciehp_enable_slot+0x1b3/0x290 [ 451.170616] pciehp_power_thread+0x3b/0xb0 [ 451.170622] process_one_work+0x149/0x360 [ 451.170623] worker_thread+0x4d/0x3c0 [ 451.170626] kthread+0x109/0x140 [ 451.170627] ? rescuer_thread+0x380/0x380 [ 451.170628] ? kthread_park+0x60/0x60 [ 451.170632] ret_from_fork+0x25/0x30 Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ena: reduce the severity of some printoutsNetanel Belgazal2017-10-191-2/+2
| | | | | | | | Decrease log level of checksum errors as these messages can be triggered remotely by bad packets. Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ibmvnic: Fix calculation of number of TX header descriptorsThomas Falcon2017-10-181-8/+8
| | | | | | | | This patch correctly sets the number of additional header descriptors that will be sent in an indirect SCRQ entry. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlxsw: core: Fix possible deadlockIdo Schimmel2017-10-181-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an EMAD is transmitted, a timeout work item is scheduled with a delay of 200ms, so that another EMAD will be retried until a maximum of five retries. In certain situations, it's possible for the function waiting on the EMAD to be associated with a work item that is queued on the same workqueue (`mlxsw_core`) as the timeout work item. This results in flushing a work item on the same workqueue. According to commit e159489baa71 ("workqueue: relax lockdep annotation on flush_work()") the above may lead to a deadlock in case the workqueue has only one worker active or if the system in under memory pressure and the rescue worker is in use. The latter explains the very rare and random nature of the lockdep splats we have been seeing: [ 52.730240] ============================================ [ 52.736179] WARNING: possible recursive locking detected [ 52.742119] 4.14.0-rc3jiri+ #4 Not tainted [ 52.746697] -------------------------------------------- [ 52.752635] kworker/1:3/599 is trying to acquire lock: [ 52.758378] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c4fa4>] flush_work+0x3a4/0x5e0 [ 52.767837] but task is already holding lock: [ 52.774360] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0 [ 52.784495] other info that might help us debug this: [ 52.791794] Possible unsafe locking scenario: [ 52.798413] CPU0 [ 52.801144] ---- [ 52.803875] lock(mlxsw_core_driver_name); [ 52.808556] lock(mlxsw_core_driver_name); [ 52.813236] *** DEADLOCK *** [ 52.819857] May be due to missing lock nesting notation [ 52.827450] 3 locks held by kworker/1:3/599: [ 52.832221] #0: (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0 [ 52.842846] #1: ((&(&bridge->fdb_notify.dw)->work)){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0 [ 52.854537] #2: (rtnl_mutex){+.+.}, at: [<ffffffff822ad8e7>] rtnl_lock+0x17/0x20 [ 52.863021] stack backtrace: [ 52.867890] CPU: 1 PID: 599 Comm: kworker/1:3 Not tainted 4.14.0-rc3jiri+ #4 [ 52.875773] Hardware name: Mellanox Technologies Ltd. "MSN2100-CB2F"/"SA001017", BIOS 5.6.5 06/07/2016 [ 52.886267] Workqueue: mlxsw_core mlxsw_sp_fdb_notify_work [mlxsw_spectrum] [ 52.894060] Call Trace: [ 52.909122] __lock_acquire+0xf6f/0x2a10 [ 53.025412] lock_acquire+0x158/0x440 [ 53.047557] flush_work+0x3c4/0x5e0 [ 53.087571] __cancel_work_timer+0x3ca/0x5e0 [ 53.177051] cancel_delayed_work_sync+0x13/0x20 [ 53.182142] mlxsw_reg_trans_bulk_wait+0x12d/0x7a0 [mlxsw_core] [ 53.194571] mlxsw_core_reg_access+0x586/0x990 [mlxsw_core] [ 53.225365] mlxsw_reg_query+0x10/0x20 [mlxsw_core] [ 53.230882] mlxsw_sp_fdb_notify_work+0x2a3/0x9d0 [mlxsw_spectrum] [ 53.237801] process_one_work+0x8f1/0x12f0 [ 53.321804] worker_thread+0x1fd/0x10c0 [ 53.435158] kthread+0x28e/0x370 [ 53.448703] ret_from_fork+0x2a/0x40 [ 53.453017] mlxsw_spectrum 0000:01:00.0: EMAD retries (2/5) (tid=bf4549b100000774) [ 53.453119] mlxsw_spectrum 0000:01:00.0: EMAD retries (5/5) (tid=bf4549b100000770) [ 53.453132] mlxsw_spectrum 0000:01:00.0: EMAD reg access failed (tid=bf4549b100000770,reg_id=200b(sfn),type=query,status=0(operation performed)) [ 53.453143] mlxsw_spectrum 0000:01:00.0: Failed to get FDB notifications Fix this by creating another workqueue for EMAD timeouts, thereby preventing the situation of a work item trying to flush a work item queued on the same workqueue. Fixes: caf7297e7ab5f ("mlxsw: core: Introduce support for asynchronous EMAD register access") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnxt_en: Fix possible corruption in DCB parameters from firmware.Sankar Patchineelam2017-10-141-5/+18
| | | | | | | | | | | | hwrm_send_message() is replaced with _hwrm_send_message(), and hwrm_cmd_lock mutex lock is grabbed for the whole period of firmware call until the firmware DCB parameters have been copied. This will prevent possible corruption of the firmware data. Fixes: 7df4ae9fe855 ("bnxt_en: Implement DCBNL to support host-based DCBX.") Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnxt_en: Fix possible corrupted NVRAM parameters from firmware response.Michael Chan2017-10-143-1/+10
| | | | | | | | | | | | | | | | In bnxt_find_nvram_item(), it is copying firmware response data after releasing the mutex. This can cause the firmware response data to be corrupted if the next firmware response overwrites the response buffer. The rare problem shows up when running ethtool -i repeatedly. Fix it by calling the new variant _hwrm_send_message_silent() that requires the caller to take the mutex and to release it after the response data has been copied. Fixes: 3ebf6f0a09a2 ("bnxt_en: Add installed-package version reporting via Ethtool GDRVINFO") Reported-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnxt_en: Fix VF resource checking.Michael Chan2017-10-141-2/+9
| | | | | | | | | | In bnxt_sriov_enable(), we calculate to see if we have enough hardware resources to enable the requested number of VFs. The logic to check for minimum completion rings and statistics contexts is missing. Add the required checks so that VF configuration won't fail. Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnxt_en: Fix VF PCIe link speed and width logic.Vasundhara Volam2017-10-141-1/+1
| | | | | | | | | | PCIE PCIE_EP_REG_LINK_STATUS_CONTROL register is only defined in PF config space, so we must read it from the PF. Fixes: 90c4f788f6c0 ("bnxt_en: Report PCIe link speed and width during driver load") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnxt_en: Don't use rtnl lock to protect link change logic in workqueue.Michael Chan2017-10-143-12/+21
| | | | | | | | | | | | | | As a further improvement to the PF/VF link change logic, use a private mutex instead of the rtnl lock to protect link change logic. With the new mutex, we don't have to take the rtnl lock in the workqueue when we have to handle link related functions. If the VF and PF drivers are running on the same host and both take the rtnl lock and one is waiting for the other, it will cause timeout. This patch fixes these timeouts. Fixes: 90c694bb7181 ("bnxt_en: Fix RTNL lock usage on bnxt_update_link().") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnxt_en: Improve VF/PF link change logic.Michael Chan2017-10-141-13/+53
| | | | | | | | | | | | | | | | | | Link status query firmware messages originating from the VFs are forwarded to the PF. The driver handles these interactions in a workqueue for the VF and PF. The VF driver waits for the response from the PF in the workqueue. If the PF and VF driver are running on the same host and the work for both PF and VF are queued on the same workqueue, the VF driver may not get the response if the PF work item is queued behind it on the same workqueue. This will lead to the VF link query message timing out. To prevent this, we create a private workqueue for PFs instead of using the common workqueue. The VF query and PF response will never be on the same workqueue. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: stmmac: dwmac_lib: fix interchanged sleep/timeout values in DMA reset ↵Emiliano Ingrassia2017-10-131-1/+1
| | | | | | | | | | | | | | function The DMA reset timeout, used in read_poll_timeout, is ten times shorter than the sleep time. This patch fixes these values interchanging them, as it was before the read_poll_timeout introduction. Fixes: 8a70aeca80c2 ("net: stmmac: Use readl_poll_timeout") Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* liquidio: fix timespec64_to_ns typoArnd Bergmann2017-10-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | While experimenting with changes to the timekeeping code, I ran into a build error in the liquidio driver: drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'liquidio_ptp_settime': drivers/net/ethernet/cavium/liquidio/lio_main.c:1850:22: error: passing argument 1 of 'timespec_to_ns' from incompatible pointer type [-Werror=incompatible-pointer-types] The driver had a type mismatch since it was first merged, but this never caused problems because it is only built on 64-bit architectures that define timespec and timespec64 to the same type. If we ever want to compile-test the driver on 32-bit or change the way that 64-bit timespec64 is defined, we need to fix it, so let's just do it now. Fixes: f21fb3ed364b ("Add support of Cavium Liquidio ethernet adapters") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* r8169: only enable PCI wakeups when WOL is activeDaniel Drake2017-10-111-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | rtl_init_one() currently enables PCI wakeups if the ethernet device is found to be WOL-capable. There is no need to do this when rtl8169_set_wol() will correctly enable or disable the same wakeup flag when WOL is activated/deactivated. This works around an ACPI DSDT bug which prevents the Acer laptop models Aspire ES1-533, Aspire ES1-732, PackardBell ENTE69AP and Gateway NE533 from entering S3 suspend - even when no ethernet cable is connected. On these platforms, the DSDT says that GPE08 is a wakeup source for ethernet, but this GPE fires as soon as the system goes into suspend, waking the system up immediately. Having the wakeup normally disabled avoids this issue in the default case. With this change, WOL will continue to be unusable on these platforms (it will instantly wake up if WOL is later enabled by the user) but we do not expect this to be a commonly used feature on these consumer laptops. We have separately determined that WOL works fine without any ACPI GPEs enabled during sleep, so a DSDT fix or override would be possible to make WOL work. Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* nfp: handle page allocation failuresJakub Kicinski2017-10-101-6/+14
| | | | | | | | | | | page_address() does not handle NULL argument gracefully, make sure we NULL-check the page pointer before passing it to page_address(). Fixes: ecd63a0217d5 ("nfp: add XDP support in the driver") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* nfp: fix ethtool stats gather retryJakub Kicinski2017-10-101-3/+5
| | | | | | | | | | The while loop fetching 64 bit ethtool statistics may have to retry multiple times, it shouldn't modify the outside state. Fixes: 4c3523623dc0 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2025-04-15 03:33:50 +0000