| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
On 32-bit platforms packet counters are stored in a net_device_stats struct
as unsigned long integers. As a result, after some time of network activity
an overflow takes place in network packet counters. This patch makes use of
new structs for holding interface statistics.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Virtual interface should be deleted after calling unregister_netdevice
since this function ends up with sending updown_intf command to card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
TLV is used to pass ACL data to firmware in start_ap cfg80211 callback.
Use the same approach in set_mac_acl cfg80211 callback.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The field spec_ver is IC's specification mask for common code to do proper
process to specified IC. This commit add a field new rate ID for new
generation IC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
New generation ICs will support 11ac, 5G, n-NSS, etc, so we define a set of
rate ID.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
8822be is 2x2 11ac wifi chip, so report VHT capability to mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
In files halbtc8822b1ant.c and halbtc8822b2ant.c that I will submit later,
two undesired directives named BT_8822B_1ANT_COEX_DBG and
BT_8822B_2ANT_COEX_DBG will be replaced by boolean variables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Originally, btcoex controls the antenna of combo card, but solo card
is also needed to setup properly. The new ops are named with suffix
'_wifi_only' opposited to original btc_ops, and new structures and
definitions are also introduced. The wifi_only oly contains four ops that
are initial variable, hw config, scan notify, and switch band notify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Three steps of connection procedure are scan, enter/leave IPS, auth.
There is no scan between leaving IPS and sending auth, but btcoex use scan
as an important clue that indicates user is going to connect. So add scan
notifications in ips_notify to correct btcoex's state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The variable will be used by btcoex of 8822be, so we prepare this variable
in advance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
BT shares 2.4G band but not 5G band, so inform current band to btcoex to
setup antenna properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The rtlwifi newer ICs support 80M bandwidth in 5G band, so extend
get_wifi_bw() to know bandwidth 80M that helps btcoex to make correct
decisions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
There is a possible race in mt76x2_stop_hardware() since pre_tbtt and
dfs tasklets could run during driver cleanup. Fix it disabling all
pending tasklets during device removal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Do not enable DFS state machine if dfs region is set to NL80211_DFS_UNSET
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add mt76x2_dfs_set_domain routine in order to properly reconfigure
pattern detector when DFS domain has been changed
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Substitute tasklet_kill with tasklet_disable/tasklet_enable in order to
guarantee dfs tasklet can not be executed during dfs parameter
initialization
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Hardware encryption seems to break encrypted unicast mgmt tx.
Unfortunately the hardware TXWI header does not have a bit to indicate
that a frame is software encrypted, so sw-encrypted frames need to use a
different WCID. For that to work, the CCMP PN needs to be generated in
software, which makes things a bit slower, so only do it for keys that
also need to tx management frames.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Fix hw queue configuration since mt76x2 devices use a reverse queue
enumeration respect to mac80211 one:
- 0: AC_BE
- 1: AC_BK
- 2: AC_VI
- 3: AC_VO
The issue can be reproduced sending two concurrent flow using
two separate queues:
- VO: 20Mbps UDP traffic
- BE: TCP traffic
In this scenario the UDP traffic will be blocked by the TCP one.
Fix it configuring properly WMM hw queue parameters
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Tested-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | |\ \
| | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Less than a handful of changes:
* possible memory leak fix in hwsim
* speed up hwsim
* add hwsim userspace rate control API
* code cleanups
====================
A conflict was resolved in mac80211_hwsim.c, mostly of
the simple overlapping changes category. One adding
a rhashtable and another adding a workqueue.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
'hwname' is malloced in hwsim_new_radio_nl() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ff4dd73dd2b4 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
For correct interpretation of a tx rate, the corresponding rate flags are
needed (e.g. whether a HT-MCS rate or a legacy rate) and moreover for more
correct simulation the other infos of the flags are important (like
short-GI). Keeping compatibility, the flags are not integrated into the
existing hwsim_tx_rate, but transmitted as an additional netlink attribute.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch adds a rhastable for mac address lookup of hwsim radios. This
especially improve the speed on reception of a netlink message with a new
frame. Although redundant, we keep holding a normal list for all radios,
since the rhashtable_walk interface adds a lot of overhead for iterating
over all radios and the doc of rhashtable recommend a redundant structure
for stable walks in such situations.
Since rhashtable is rcu protected we do not need a lock for delivering
frames and thus improving this scenario.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[remove hash function, it would cause alignment issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Final few patches before the merge window, nothing really special.
ath9k
* add MSI support (not enabled by default yet)
rtlwifi
* support A-MSDU in A-MPDU aggregation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Due to the fact that A-MSDU deaggregation is done in software,
we set this flag to support the A-MSDU in A-MPDU
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
btcoex configure antenna by rfe_type that is RF type programmed in efuse.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This commit implement the common function to sort old features, and add
more new features that are get_supported_feature, get_supported_version,
get_ant_det_val, ble_scan_type, ble_scan_para, bt_dev_info,
forbidden_slot_val, afh_map and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Each of these typedefs are only referenced in a single location later
in this header. Thus, they are easily removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Remove global variables, so btcoexist can support multiple instances
simultaneously.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
After mac power-on sequence, wifi will start to work so notify btcoex the
event to configure registers especially related to antenna. This will not
only help to assign antenna but also to yield better user experience.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When AP change bandwidth setting from 20M to 40M, STA may use old 20M AP
information to association with AP. Driver unlink bss in the
.bss_info_changed of ieee80211_ops to make sure that later scan can get
correct AP bandwidth capability.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
If there is no connection, driver will enter IPS state. Meanwhile, it
fails to scan channel 1 by the command 'iw dev wlan0 scan freq 2412',
because hardware channel setting lose after IPS. Thus, restore channel
setting from hw->conf.channel set by last rtl_op_config().
Signed-off-by: Tim Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Enter/leavel IPS and LPS are large critical section, and they can't use
sleep function because running in atomic-context, which own a spin_lock.
In commit ba9f93f82aba ("rtlwifi: Fix enter/exit power_save"), it moves
LPS functions to thread-context, so this commit can simply change LPS's
spin lock to mutex.
Considering IPS functions, rtl_ips_nic_on() may be called by TX tasklet
(softirq-context) that check whether packet is auth frame. Fortunately,
current mac80211 will ask driver to leave IPS using op_config with
changed flag IEEE80211_CONF_CHANGE_IDLE, before issuing auth frame, so
IPS functions can run in thread-context and use mutex to protect critical
section, too.
Also, this commit removes some useless spin locks.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Verify wcid is not NULL before dereferencing the pointer to initialize
txwi rate/power info
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Initialize mt76_txq pointer after ieee80211_txq pointer check.
Remove space after the pointer cast
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |\ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
ath.git patches for 4.16. Major changes:
ath9k
* add MSI support (not enabled by default yet)
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Checkpatch found these issues:
drivers/net/wireless/ath/ath10k/ce.h:324: Please use a blank line after function/struct/union/enum declarations
drivers/net/wireless/ath/ath10k/core.c:1321: Please don't use multiple blank lines
drivers/net/wireless/ath/ath10k/htt.h:1859: Please use a blank line after function/struct/union/enum declarations
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Variable section_table.size is a u32 and so cannot be less than
zero, hence the less than zero check is redundant and can be
removed.
Detected by CoverityScan, CID#1463855 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Trivial fix to spelling mistake in warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Validate ie_len after the alignment padding before access the buffer
to avoid potential overflow.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Some platform(BIOS) blocks legacy interrupts (INTx), and only allows MSI
for WLAN device. So adding a quirk to list those machines and set
use_msi automatically.
Adding the following platforms to the quirk.
Dell Inspiron 24-3460
Dell Inspiron 3472
Dell Inspiron 14-3473
Dell Vostro 3262
Dell Vostro 15-3572
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
On new Intel platforms like ApolloLake, legacy interrupt mechanism
(INTx) is not supported, so WLAN modules are not working because
interrupts are missing, therefore this patch is to add MSI support to
ath9k. With module paremeter "use_msi=1", ath9k driver would try to
use MSI instead of INTx.
Signed-off-by: Russell Hu <rhu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Commit b014e96d1abb ("PCI: Protect pci_error_handlers->reset_notify()
usage with device_lock()") resolves races between driver reset and
removal, but it introduces some new deadlock problems. If we see a
timeout while we've already started suspending, removing, or shutting
down the driver, we might see:
(a) a worker thread, running mwifiex_pcie_work() ->
mwifiex_pcie_card_reset_work() -> pci_reset_function()
(b) a removal thread, running mwifiex_pcie_remove() ->
mwifiex_free_adapter() -> mwifiex_unregister() ->
mwifiex_cleanup_pcie() -> cancel_work_sync(&card->work)
Unfortunately, mwifiex_pcie_remove() already holds the device lock that
pci_reset_function() is now requesting, and so we see a deadlock.
It's necessary to cancel and synchronize our outstanding work before
tearing down the driver, so we can't have this work wait indefinitely
for the lock.
It's reasonable to only "try" to reset here, since this will mostly
happen for cases where it's already difficult to reset the firmware
anyway (e.g., while we're suspending or powering off the system). And if
reset *really* needs to happen, we can always try again later.
Fixes: b014e96d1abb ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()")
Cc: <stable@vger.kernel.org>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This reverts commit b713bbf1471b56b572ce26bd02b81a85c2b007f4.
The "fix" in question does not actually fix all related problems, and it
also introduces new deadlock possibilities. Since commit b014e96d1abb
("PCI: Protect pci_error_handlers->reset_notify() usage with
device_lock()"), the race in question is actually resolved (PCIe reset
cannot happen at the same time as remove()). Instead, this "fix" just
introduces a deadlock where mwifiex_pcie_card_reset_work() is waiting on
device_lock, which is held by PCIe device remove(), which is waiting
on...mwifiex_pcie_card_reset_work().
The proper thing to do is just to fix the deadlock. Patch for this will
come separately.
Cc: Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Variable fw_ps_state is assigned a value but it is never read, hence
it is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:736:2:
warning: Value stored to 'fw_ps_state' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | |\ \ \ \
| | |/ / /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Overlapping changes all over.
The mini-qdisc bits were a little bit tricky, however.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \
| | |_|_|/
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e54 ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
b43_radio_2057_init_post is not called in an interrupt handler
nor holding a spinlock.
The function mdelay in it can be replaced with usleep_range,
to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Use dma_zalloc_coherent for allocating zeroed
memory and remove unnecessary memset function.
Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
