summaryrefslogtreecommitdiffstats
path: root/drivers/pci/controller/dwc
Commit message (Collapse)AuthorAgeFilesLines
...
| | * | PCI: qcom: Enable ASPM for platforms supporting 1.9.0 opsManivannan Sadhasivam2023-10-141-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ASPM is supported by Qcom host controllers/bridges on most of the recent platforms and so the devices tested so far. But for enabling ASPM by default (without using Kconfig, kernel command-line or sysfs), BIOS has to enable ASPM on both host bridge and downstream devices during boot. Unfortunately, none of the BIOS available on Qcom platforms enables ASPM. Due to this, the platforms making use of Qcom SoCs draw high power during runtime. To fix this power draw issue, users have to enable ASPM using Kconfig, kernel command-line, sysfs or the BIOS has to start enabling ASPM. The latter may happen in the future, but that won't address the issue on current platforms. Also, asking users to enable a feature to get the power management right would provide an unpleasant out-of-the-box experience. So the apt solution is to enable ASPM in the controller driver itself. And this is being accomplished by calling pci_enable_link_state() in the newly introduced host_post_init() callback for all the devices connected to the bus. This function enables all supported link low power states for both host bridge and the downstream devices. Due to limited testing, ASPM is only enabled for platforms making use of ops_1_9_0 callbacks. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20231010155914.9516-3-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
| | * | PCI: dwc: Add host_post_init() callbackManivannan Sadhasivam2023-10-142-0/+4
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | This callback can be used by the platform drivers to do configuration once all the devices are scanned. Like changing LNKCTL of all downstream devices to enable ASPM etc... Link: https://lore.kernel.org/linux-pci/20231010155914.9516-2-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
| * | PCI: keystone: Don't discard .probe() callbackUwe Kleine-König2023-10-101-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The __init annotation makes the ks_pcie_probe() function disappear after booting completes. However a device can also be bound later. In that case, we try to call ks_pcie_probe(), but the backing memory is likely already overwritten. The right thing to do is do always have the probe callback available. Note that the (wrong) __refdata annotation prevented this issue to be noticed by modpost. Fixes: 0c4ffcfe1fbc ("PCI: keystone: Add TI Keystone PCIe driver") Link: https://lore.kernel.org/r/20231001170254.2506508-5-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org
| * | PCI: keystone: Don't discard .remove() callbackUwe Kleine-König2023-10-101-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With CONFIG_PCIE_KEYSTONE=y and ks_pcie_remove() marked with __exit, the function is discarded from the driver. In this case a bound device can still get unbound, e.g via sysfs. Then no cleanup code is run resulting in resource leaks or worse. The right thing to do is do always have the remove callback available. Note that this driver cannot be compiled as a module, so ks_pcie_remove() was always discarded before this change and modpost couldn't warn about this issue. Furthermore the __ref annotation also prevents a warning. Fixes: 0c4ffcfe1fbc ("PCI: keystone: Add TI Keystone PCIe driver") Link: https://lore.kernel.org/r/20231001170254.2506508-4-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org
| * | PCI: kirin: Don't discard .remove() callbackUwe Kleine-König2023-10-101-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With CONFIG_PCIE_KIRIN=y and kirin_pcie_remove() marked with __exit, the function is discarded from the driver. In this case a bound device can still get unbound, e.g via sysfs. Then no cleanup code is run resulting in resource leaks or worse. The right thing to do is do always have the remove callback available. This fixes the following warning by modpost: drivers/pci/controller/dwc/pcie-kirin: section mismatch in reference: kirin_pcie_driver+0x8 (section: .data) -> kirin_pcie_remove (section: .exit.text) (with ARCH=x86_64 W=1 allmodconfig). Fixes: 000f60db784b ("PCI: kirin: Add support for a PHY layer") Link: https://lore.kernel.org/r/20231001170254.2506508-3-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org
| * | PCI: exynos: Don't discard .remove() callbackUwe Kleine-König2023-10-101-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With CONFIG_PCI_EXYNOS=y and exynos_pcie_remove() marked with __exit, the function is discarded from the driver. In this case a bound device can still get unbound, e.g via sysfs. Then no cleanup code is run resulting in resource leaks or worse. The right thing to do is do always have the remove callback available. This fixes the following warning by modpost: WARNING: modpost: drivers/pci/controller/dwc/pci-exynos: section mismatch in reference: exynos_pcie_driver+0x8 (section: .data) -> exynos_pcie_remove (section: .exit.text) (with ARCH=x86_64 W=1 allmodconfig). Fixes: 340cba6092c2 ("pci: Add PCIe driver for Samsung Exynos") Link: https://lore.kernel.org/r/20231001170254.2506508-2-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Cc: stable@vger.kernel.org
| * | PCI: Use PCI_HEADER_TYPE_* instead of literalsIlpo Järvinen2023-10-031-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | Replace literals under drivers/pci/ with PCI_HEADER_TYPE_MASK, PCI_HEADER_TYPE_NORMAL, and PCI_HEADER_TYPE_MFD. Also replace !! boolean conversions with FIELD_GET(). Link: https://lore.kernel.org/r/20231003125300.5541-4-ilpo.jarvinen@linux.intel.com Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # for Renesas R-Car
* / PCI: qcom: Fix IPQ8074 enumerationSricharan Ramabadhran2023-09-291-3/+1
|/ | | | | | | | | | | | | | | | | | | | | | | PARF_SLV_ADDR_SPACE_SIZE_2_3_3 is used by qcom_pcie_post_init_2_3_3(). This PCIe slave address space size register offset is 0x358 but was incorrectly changed to 0x16c by 39171b33f652 ("PCI: qcom: Remove PCIE20_ prefix from register definitions"). This prevented access to slave address space registers like iATU, etc., so the IPQ8074 PCIe controller was not enumerated. Revert back to the correct 0x358 offset and remove the unused PARF_SLV_ADDR_SPACE_SIZE_2_3_3. Fixes: 39171b33f652 ("PCI: qcom: Remove PCIE20_ prefix from register definitions") Link: https://lore.kernel.org/r/20230919102948.1844909-1-quic_srichara@quicinc.com Tested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> [bhelgaas: commit log] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Cc: stable@vger.kernel.org # v6.4+
* Merge tag 'pci-v6.6-changes' of ↵Linus Torvalds2023-08-3021-44/+361
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull PCI updates from Bjorn Helgaas: "Enumeration: - Add locking to read/modify/write PCIe Capability Register accessors for Link Control and Root Control - Use pci_dev_id() when possible instead of manually composing ID from dev->bus->number and dev->devfn Resource management: - Move prototypes for __weak sysfs resource files to linux/pci.h to fix 'no previous prototype' warnings - Make more I/O port accesses depend on HAS_IOPORT - Use devm_platform_get_and_ioremap_resource() instead of open-coding platform_get_resource() followed by devm_ioremap_resource() Power management: - Ensure devices are powered up while accessing VPD - If device is powered-up, keep it that way while polling for PME - Only read PCI_PM_CTRL register when available, to avoid reading the wrong register and corrupting dev->current_state Virtualization: - Avoid Secondary Bus Reset on NVIDIA T4 GPUs Error handling: - Remove unused pci_disable_pcie_error_reporting() - Unexport pci_enable_pcie_error_reporting(), used only by aer.c - Unexport pcie_port_bus_type, used only by PCI core VGA: - Simplify and clean up typos in VGA arbiter Apple PCIe controller driver: - Initialize pcie->nvecs (number of available MSIs) before use Broadcom iProc PCIe controller driver: - Use of_property_read_bool() instead of low-level accessors for boolean properties Broadcom STB PCIe controller driver: - Assert PERST# when probing BCM2711 because some bootloaders don't do it Freescale i.MX6 PCIe controller driver: - Add .host_deinit() callback so we can clean up things like regulators on probe failure or driver unload Freescale Layerscape PCIe controller driver: - Add support for link-down notification so the endpoint driver can process LINK_DOWN events - Add suspend/resume support, including manual PME_Turn_off/PME_TO_Ack handshake - Save Link Capabilities during probe so they can be restored when handling a link-up event, since the controller loses the Link Width and Link Speed values during reset Intel VMD host bridge driver: - Fix disable of bridge windows during domain reset; previously we cleared the base/limit registers, which actually left the windows enabled Marvell MVEBU PCIe controller driver: - Remove unused busn member Microchip PolarFlare PCIe controller driver: - Fix interrupt bit definitions so the SEC and DED interrupt handlers work correctly - Make driver buildable as a module - Read FPGA MSI configuration parameters from hardware instead of hard-coding them Microsoft Hyper-V host bridge driver: - To avoid a NULL pointer dereference, skip MSI restore after hibernate if MSI/MSI-X hasn't been enabled NVIDIA Tegra194 PCIe controller driver: - Revert 'PCI: tegra194: Enable support for 256 Byte payload' because Linux doesn't know how to reduce MPS from to 256 to 128 bytes for endpoints below a switch (because other devices below the switch might already be operating), which leads to 'Malformed TLP' errors Qualcomm PCIe controller driver: - Add DT and driver support for interconnect bandwidth voting for 'pcie-mem' and 'cpu-pcie' interconnects - Fix broken SDX65 'compatible' DT property - Configure controller so MHI bus master clock will be switched off while in ASPM L1.x states - Use alignment restriction from EPF core in EPF MHI driver - Add Endpoint eDMA support - Add MHI eDMA support - Add Snapdragon SM8450 support to the EPF MHI driversupport - Add MHI eDMA support - Add Snapdragon SM8450 support to the EPF MHI driversupport - Add MHI eDMA support - Add Snapdragon SM8450 support to the EPF MHI driversupport - Add MHI eDMA support - Add Snapdragon SM8450 support to the EPF MHI driver - Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup latency - Add sa8775p DT binding and driver support Rockchip PCIe controller driver: - Use 64-bit mask on MSI 64-bit PCI address to avoid zeroing out the upper 32 bits SiFive FU740 PCIe controller driver: - Set the supported number of MSI vectors so we can use all available MSI interrupts Synopsys DesignWare PCIe controller driver: - Add generic dwc suspend/resume APIs (dw_pcie_suspend_noirq() and dw_pcie_resume_noirq()) to be called by controller driver suspend/resume ops, and a controller callback to send PME_Turn_Off MicroSemi Switchtec management driver: - Add support for PCIe Gen5 devices Miscellaneous: - Reorder and compress to reduce size of struct pci_dev - Fix race in DOE destroy_work_on_stack() - Add stubs to avoid casts between incompatible function types - Explicitly include correct DT includes to untangle headers" * tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (96 commits) PCI: qcom-ep: Add ICC bandwidth voting support dt-bindings: PCI: qcom: ep: Add interconnects path PCI: qcom-ep: Treat unknown IRQ events as an error dt-bindings: PCI: qcom: Fix SDX65 compatible PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API PCI: epf-mhi: Use iATU for small transfers PCI: epf-mhi: Add support for SM8450 PCI: epf-mhi: Add eDMA support PCI: qcom-ep: Add eDMA support PCI: epf-mhi: Make use of the alignment restriction from EPF core PCI/PM: Only read PCI_PM_CTRL register when available PCI: qcom: Add support for sa8775p SoC dt-bindings: PCI: qcom: Add sa8775p compatible PCI: qcom-ep: Pass alignment restriction to the EPF core PCI: Simplify pcie_capability_clear_and_set_word() control flow PCI: Tidy config space save/restore messages PCI: Fix code formatting inconsistencies PCI: Fix typos in docs and comments PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos PCI: Simplify pci_dev_driver() ...
| * Merge branch 'pci/misc'Bjorn Helgaas2023-08-2914-14/+13
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Reorder struct pci_dev to avoid holes and reduce size (Christophe JAILLET) - Change pdev->rom_attr_enabled to single bit since it's only a boolean value (Christophe JAILLET) - Use struct_size() in pirq_convert_irt_table() instead of hand-writing it (Christophe JAILLET) - Explicitly include correct DT includes to untangle headers (Rob Herring) - Fix a DOE race between destroy_work_on_stack() and the stack-allocated task->work struct going out of scope in pci_doe() (Ira Weiny) - Use pci_dev_id() when possible instead of manually composing ID from dev->bus->number and dev->devfn (Xiongfeng Wang, Zheng Zengkai) - Move pci_create_resource_files() declarations to linux/pci.h for alpha build warnings (Arnd Bergmann) - Remove unused hotplug function declarations (Yue Haibing) - Remove unused mvebu struct mvebu_pcie.busn (Pali Rohár) - Unexport pcie_port_bus_type (Bjorn Helgaas) - Remove unnecessary sysfs ID local variable initialization (Bjorn Helgaas) - Fix BAR value printk formatting to accommodate 32-bit values (Bjorn Helgaas) - Use consistent pointer types for config access syscall get_user() and put_user() uses (Bjorn Helgaas) - Simplify AER_RECOVER_RING_SIZE definition (Bjorn Helgaas) - Simplify pci_pio_to_address() (Bjorn Helgaas) - Simplify pci_dev_driver() (Bjorn Helgaas) - Fix pci_bus_resetable(), pci_slot_resetable() name typos (Bjorn Helgaas) - Fix code and doc typos and code formatting (Bjorn Helgaas) - Tidy config space save/restore messages (Bjorn Helgaas) * pci/misc: PCI: Tidy config space save/restore messages PCI: Fix code formatting inconsistencies PCI: Fix typos in docs and comments PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos PCI: Simplify pci_dev_driver() PCI: Simplify pci_pio_to_address() PCI/AER: Simplify AER_RECOVER_RING_SIZE definition PCI: Use consistent put_user() pointer types PCI: Fix printk field formatting PCI: Remove unnecessary initializations PCI: Unexport pcie_port_bus_type PCI: mvebu: Remove unused busn member PCI: Remove unused function declarations PCI/sysfs: Move declarations to linux/pci.h PCI/P2PDMA: Use pci_dev_id() to simplify the code PCI/IOV: Use pci_dev_id() to simplify the code PCI/AER: Use pci_dev_id() to simplify the code PCI: apple: Use pci_dev_id() to simplify the code PCI/DOE: Fix destroy_work_on_stack() race PCI: Explicitly include correct DT includes x86/PCI: Use struct_size() in pirq_convert_irt_table() PCI: Change pdev->rom_attr_enabled to single bit PCI: Reorder pci_dev fields to reduce holes
| | * PCI: Explicitly include correct DT includesRob Herring2023-07-1814-14/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Link: https://lore.kernel.org/r/20230714174827.4061572-1-robh@kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
| * | Merge branch 'pci/controller/resources'Bjorn Helgaas2023-08-291-2/+1
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Use Use devm_platform_get_and_ioremap_resource() instead of open-coding platform_get_resource() followed by devm_ioremap_resource() (Yang Li) * pci/controller/resources: PCI: imx6: Use devm_platform_get_and_ioremap_resource() PCI: xgene-msi: Use devm_platform_get_and_ioremap_resource() PCI: v3: Use devm_platform_get_and_ioremap_resource() PCI: rcar-gen2: Use devm_platform_get_and_ioremap_resource()
| | * | PCI: imx6: Use devm_platform_get_and_ioremap_resource()Yang Li2023-07-131-2/+1
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert calls to platform_get_resource() and devm_ioremap_resource() into a single call to devm_platform_get_and_ioremap_resource(), to simplify the code. This new helper added in commit 890cc39a8799 ("drivers: provide devm_platform_get_and_ioremap_resource()") does what both of the other separate functions do. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20230323074553.90372-1-yang.lee@linux.alibaba.com Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
| * | Merge branch 'pci/controller/remove-void-cast'Bjorn Helgaas2023-08-292-6/+16
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Add stubs for devm action functions that call clk_disable_unprepare() to avoid casts between incompatible function types (Krzysztof Wilczyński) * pci/controller/remove-void-cast: PCI: microchip: Remove cast between incompatible function type PCI: keembay: Remove cast between incompatible function type PCI: meson: Remove cast between incompatible function type
| | * | PCI: keembay: Remove cast between incompatible function typeKrzysztof Wilczyński2023-07-131-3/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rather than casting void(*)(struct clk *) to void (*)(void *), that forces conversion to an incompatible function type, replace the cast with a small local stub function with a signature that matches what the devm_add_action_or_reset() function expects. The sub function takes a void *, then passes it directly to clk_disable_unprepare(), which handles the more specific type. Reported by clang when building with warnings enabled: drivers/pci/controller/dwc/pcie-keembay.c:172:12: warning: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Wcast-function-type-strict] (void(*)(void *))clk_disable_unprepare, ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ No functional changes are intended. Fixes: 0c87f90b4c13 ("PCI: keembay: Add support for Intel Keem Bay") Link: https://lore.kernel.org/linux-pci/20230629165956.237832-2-kwilczynski@kernel.org Acked-by: Srikanth Thokala <srikanth.thokala@intel.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
| | * | PCI: meson: Remove cast between incompatible function typeKrzysztof Wilczyński2023-07-131-3/+8
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rather than casting void(*)(struct clk *) to void (*)(void *), that forces conversion to an incompatible function type, replace the cast with a small local stub function with a signature that matches what the devm_add_action_or_reset() function expects. The sub function takes a void *, then passes it directly to clk_disable_unprepare(), which handles the more specific type. Reported by clang when building with warnings enabled: drivers/pci/controller/dwc/pci-meson.c:191:6: warning: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Wcast-function-type-strict] (void (*) (void *))clk_disable_unprepare, ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ No functional changes are intended. Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver") Link: https://lore.kernel.org/linux-pci/20230629165956.237832-1-kwilczynski@kernel.org Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
| * | Merge branch 'pci/controller/tegra194'Bjorn Helgaas2023-08-291-10/+0
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Revert "PCI: tegra194: Enable support for 256 Byte payload" because Linux doesn't know how to reduce MPS from to 256 to 128 bytes for Endpoints below a Switch (because other devices below the Switch might already be operating), which leads to Malformed TLP errors (Vidya Sagar) * pci/controller/tegra194: Revert "PCI: tegra194: Enable support for 256 Byte payload"
| | * | Revert "PCI: tegra194: Enable support for 256 Byte payload"Vidya Sagar2023-08-031-10/+0
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After commit 4fb8e46c1bc4 ("PCI: tegra194: Enable support for 256 Byte payload"), we initialize MPS=256 for tegra194 Root Ports before enumerating the hierarchy. Consider an Endpoint that supports only MPS=128. In the default situation (CONFIG_PCIE_BUS_DEFAULT set and no "pci=pcie_bus_*" parameter), Linux tries to configure the MPS of every device to match the upstream bridge. If the Endpoint is directly below the Root Port, Linux can reduce the Root Port MPS to 128 to match the Endpoint. But if there's a switch in the middle, Linux doesn't reduce the Root Port MPS because other devices below the switch may already be configured with MPS larger than 128. This scenario results in uncorrectable Malformed TLP errors if the Root Port sends TLPs with payloads larger than 128 bytes. These errors can be avoided by using the "pci=pcie_bus_safe" parameter, but it doesn't seem to be a good idea to always have this parameter even for basic functionality to work. Revert commit 4fb8e46c1bc4 ("PCI: tegra194: Enable support for 256 Byte payload") so the Root Ports default to MPS=128, which all devices support. If peer-to-peer DMA is not required, one can use "pci=pcie_bus_perf" to get the benefit of larger MPS settings. [bhelgaas: commit log; kwilczynski: retain "u16 val_16" declaration at the top, add missing acked by tag] Fixes: 4fb8e46c1bc4 ("PCI: tegra194: Enable support for 256 Byte payload") Link: https://lore.kernel.org/linux-pci/20230619102604.3735001-1-vidyas@nvidia.com Signed-off-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Acked-by: Jon Hunter <jonathanh@nvidia.com> Cc: stable@vger.kernel.org # v6.0-rc1+
| * | Merge branch 'pci/controller/qcom-ep'Bjorn Helgaas2023-08-291-1/+73
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Log unknown Qcom Endpoint IRQ events at error level, not debug level (Manivannan Sadhasivam) - Add DT and driver support for qcom interconnect bandwidth voting for "pcie-mem" and "cpu-pcie" interconnects (Krishna chaitanya chundru) * pci/controller/qcom-ep: PCI: qcom-ep: Add ICC bandwidth voting support dt-bindings: PCI: qcom: ep: Add interconnects path PCI: qcom-ep: Treat unknown IRQ events as an error
| | * | PCI: qcom-ep: Add ICC bandwidth voting supportKrishna chaitanya chundru2023-08-291-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for voting interconnect (ICC) bandwidth based on the link speed and width. This commit is inspired from the basic interconnect support added to pcie-qcom driver in commit c4860af88d0c ("PCI: qcom: Add basic interconnect support"). The interconnect support is kept optional to be backward compatible with legacy device trees. [kwilczynski: add missing kernel-doc for the icc_mem variable] Link: https://lore.kernel.org/linux-pci/1689751218-24492-5-git-send-email-quic_krichai@quicinc.com Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
| | * | PCI: qcom-ep: Treat unknown IRQ events as an errorManivannan Sadhasivam2023-08-291-1/+1
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sometimes, the Qcom PCIe EP controller can receive some interrupts unknown to the driver, like safety interrupts in newer SoCs. In those cases, if the driver doesn't clear the interrupts, it will end up in an interrupt storm. However, the users will not know about it because the log is treated as a debug message. So let's treat the unknown event log as an error so that it at least makes the user aware, thereby getting fixed eventually. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20230726152931.18134-1-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
| * | Merge branch 'pci/controller/qcom-edma'Bjorn Helgaas2023-08-291-1/+4
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Pass the Qcom Endpoint 4K alignment requirement for outbound windows to the EPF core so EPF drivers can use it (Manivannan Sadhasivam) - Use alignment restriction from EPF core in Qcom EPF MHI driver (Manivannan Sadhasivam) - Add Qcom Endpoint eDMA support by enabling the eDMA IRQ (Manivannan Sadhasivam) - Add Qcom MHI eDMA support (Manivannan Sadhasivam) - Add Qcom Snapdragon SM8450 support to the EPF MHI driver (Manivannan Sadhasivam) - Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup latency (Manivannan Sadhasivam) - Add pci_epc_mem_init() kernel-doc (Manivannan Sadhasivam) * pci/controller/qcom-edma: PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API PCI: epf-mhi: Use iATU for small transfers PCI: epf-mhi: Add support for SM8450 PCI: epf-mhi: Add eDMA support PCI: qcom-ep: Add eDMA support PCI: epf-mhi: Make use of the alignment restriction from EPF core PCI: qcom-ep: Pass alignment restriction to the EPF core
| | * | PCI: qcom-ep: Add eDMA supportManivannan Sadhasivam2023-08-261-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qualcomm PCIe Endpoint controllers have the in-built Embedded DMA (eDMA) peripheral for offloading the data transfer between the PCIe bus and memory. Let's add support for it by enabling the eDMA IRQ in the driver. The eDMA DMA Engine driver will handle the rest of the functionality. Since the eDMA on Qualcomm platforms only uses a single IRQ for all channels, use 1 for edma.nr_irqs. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20230717065459.14138-4-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
| | * | PCI: qcom-ep: Pass alignment restriction to the EPF coreManivannan Sadhasivam2023-08-251-0/+1
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | Qcom PCIe EP controllers have 4K alignment restriction for the outbound window address. Hence, pass this info to the EPF core so that the EPF drivers can make use of this info. Link: https://lore.kernel.org/linux-pci/20230717065459.14138-2-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
| * | Merge branch 'pci/controller/qcom'Bjorn Helgaas2023-08-292-1/+2
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Configure controller so MHI bus master clock will be switched off while in ASPM L1.x states (Manivannan Sadhasivam) - Add sa8775p DT binding and driver support (Mrinmay Sarkar) - Fix broken DT SDX65 "compatible" property (Krzysztof Kozlowski) * pci/controller/qcom: dt-bindings: PCI: qcom: Fix SDX65 compatible PCI: qcom: Add support for sa8775p SoC dt-bindings: PCI: qcom: Add sa8775p compatible PCI: qcom-ep: Switch MHI bus master clock off during L1SS
| | * | PCI: qcom: Add support for sa8775p SoCMrinmay Sarkar2023-08-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for sa8775p SoC that uses controller version 5.90 reusing the 1.9.0 config. Link: https://lore.kernel.org/linux-pci/1689960276-29266-3-git-send-email-quic_msarkar@quicinc.com Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
| | * | PCI: qcom-ep: Switch MHI bus master clock off during L1SSManivannan Sadhasivam2023-07-131-1/+1
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, as part of the qcom_pcie_perst_deassert() function, instead of writing the updated value to clear PARF_MSTR_AXI_CLK_EN, the variable "val" is re-read. This must be fixed to ensure that the master clock supplied to the MHI bus is correctly gated during L1.1/L1.2 to save power. Thus, replace the line that re-reads "val" with a line that writes the updated value to the register to clear PARF_MSTR_AXI_CLK_EN. [kwilczynski: commit log] Fixes: c457ac029e44 ("PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS") Link: https://lore.kernel.org/linux-pci/20230627141036.11600-1-manivannan.sadhasivam@linaro.org Reported-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
| * | Merge branch 'pci/controller/layerscape'Bjorn Helgaas2023-08-291-0/+20
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Add support for link-down notification so the endpoint driver can process LINK_DOWN events (Frank Li) - Save Link Capabilities during probe so they can be restored when handling a link-up event, since the controller loses the Link Width and Link Speed values during reset (Xiaowei Bao) * pci/controller/layerscape: PCI: layerscape: Add workaround for lost link capabilities during reset PCI: layerscape: Add support for link-down notification
| | * | PCI: layerscape: Add workaround for lost link capabilities during resetXiaowei Bao2023-08-241-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The endpoint controller loses the Maximum Link Width and Supported Link Speed value from the Link Capabilities Register - initially configured by the Reset Configuration Word (RCW) - during a link-down or hot reset event. Address this issue in the endpoint event handler. Link: https://lore.kernel.org/r/20230720135834.1977616-2-Frank.Li@nxp.com Fixes: a805770d8a22 ("PCI: layerscape: Add EP mode support") Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Acked-by: Manivannan Sadhasivam <mani@kernel.org>
| | * | PCI: layerscape: Add support for link-down notificationFrank Li2023-08-241-0/+1
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support to pass link-down notification to the endpoint function driver so that it can process the LINK_DOWN event. Link: https://lore.kernel.org/r/20230720135834.1977616-1-Frank.Li@nxp.com Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Acked-by: Manivannan Sadhasivam <mani@kernel.org>
| * | Merge branch 'pci/controller/fu740'Bjorn Helgaas2023-08-291-0/+1
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Set the supported number of MSI vectors so we can use all available MSI interrupts (Yong-Xuan Wang) * pci/controller/fu740: PCI: fu740: Set the number of MSI vectors
| | * | PCI: fu740: Set the number of MSI vectorsYong-Xuan Wang2023-08-231-0/+1
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The iMSI-RX module of the DW PCIe controller provides multiple sets of MSI_CTRL_INT_i_* registers, and each set is capable of handling 32 MSI interrupts. However, the fu740 PCIe controller driver only enabled one set of MSI_CTRL_INT_i_* registers, as the total number of supported interrupts was not specified. Set the supported number of MSI vectors to enable all the MSI_CTRL_INT_i_* registers on the fu740 PCIe core, allowing the system to fully utilize the available MSI interrupts. Link: https://lore.kernel.org/r/20230807055621.2431-1-yongxuan.wang@sifive.com Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
| * | PCI: layerscape: Add power management support for ls1028aHou Zhiqiang2023-08-241-9/+131
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add PME_Turn_off/PME_TO_Ack handshake sequence for ls1028a platform. Implemented on top of common dwc dw_pcie_suspend(resume)_noirq() functions to handle system enter/exit suspend states. Link: https://lore.kernel.org/r/20230821184815.2167131-4-Frank.Li@nxp.com Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Acked-by: Manivannan Sadhasivam <mani@kernel.org>
| * | PCI: dwc: Implement generic suspend/resume functionalityFrank Li2023-08-242-0/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce an helper function (dw_pcie_get_ltssm()) to retrieve SMLH_LTSS_STATE. Add common dw_pcie_suspend(resume)_noirq() API to implement the DWC controller generic suspend/resume functionality. Add a controller specific callback to send the PME_Turn_Off message (ie .pme_turn_off) for controller platform specific PME handling. Link: https://lore.kernel.org/r/20230821184815.2167131-3-Frank.Li@nxp.com Signed-off-by: Frank Li <Frank.Li@nxp.com> [lpieralisi@kernel.org: commit log] Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Acked-by: Manivannan Sadhasivam <mani@kernel.org>
| * | PCI: dwc: Provide deinit callback for i.MXMark Brown2023-08-081-0/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The i.MX integration for the DesignWare PCI controller has a _host_exit() operation which undoes everything that the _host_init() operation does but does not wire this up as the host_deinit callback for the core, or call it in any path other than suspend. This means that if we ever unwind the initial probe of the device, for example because it fails, the regulator core complains that the regulators for the device were left enabled: imx6q-pcie 33800000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 16G imx6q-pcie 33800000.pcie: Phy link never came up imx6q-pcie 33800000.pcie: Phy link never came up imx6q-pcie: probe of 33800000.pcie failed with error -110 ------------[ cut here ]------------ WARNING: CPU: 2 PID: 46 at drivers/regulator/core.c:2396 _regulator_put+0x110/0x128 Wire up the callback so that the core can clean up after itself. Link: https://lore.kernel.org/r/20230731-pci-imx-regulator-cleanup-v2-1-fc8fa5c9893d@kernel.org Tested-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
* / Revert "PCI: dwc: Wait for link up only if link is started"Johan Hovold2023-07-263-23/+11
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit da56a1bfbab55189595e588f1d984bdfb5cf5924. Bjorn Andersson, Fabio Estevam, Xiaolei Wang, and Jon Hunter reported that da56a1bfbab5 ("PCI: dwc: Wait for link up only if link is started") broke controller probing by returning an error in case the link does not come up during host initialisation, for example when the slot is empty. As explained in commit 886a9c134755 ("PCI: dwc: Move link handling into common code") and as indicated by the comment "Ignore errors, the link may come up later" in the code, waiting for link up and ignoring errors is the intended behaviour: Let's standardize this to succeed as there are usecases where devices (and the link) appear later even without hotplug. For example, a reconfigured FPGA device. Reverting the offending commit specifically fixes a regression on Qualcomm platforms like the Lenovo ThinkPad X13s which no longer reach the interconnect sync state if a slot does not have a device populated (e.g. an optional modem). Note that enabling asynchronous probing by default as was done for Qualcomm platforms by commit c0e1eb441b1d ("PCI: qcom: Enable async probe by default"), should take care of any related boot time concerns. Finally, note that the intel-gw driver is the only driver currently not providing a .start_link() callback and instead starts the link in its .host_init() callback, which may avoid an additional one-second timeout during probe by making the link-up wait conditional. If anyone cares, that can be done in a follow-up patch with a proper motivation. [bhelgaas: add Fabio Estevam, Xiaolei Wang, Jon Hunter reports] Fixes: da56a1bfbab5 ("PCI: dwc: Wait for link up only if link is started") Link: https://lore.kernel.org/r/20230706082610.26584-1-johan+linaro@kernel.org Reported-by: Bjorn Andersson <quic_bjorande@quicinc.com> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reported-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20230704122635.1362156-1-festevam@gmail.com/ Reported-by: Xiaolei Wang <xiaolei.wang@windriver.com> Link: https://lore.kernel.org/r/20230705010624.3912934-1-xiaolei.wang@windriver.com/ Reported-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/6ca287a1-6c7c-7b90-9022-9e73fb82b564@nvidia.com Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Sajid Dalvi <sdalvi@google.com> Cc: Ajay Agarwal <ajayagarwal@google.com>
* Merge tag 'dmaengine-6.5-rc1' of ↵Linus Torvalds2023-07-061-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine Pull dmaengine updates from Vinod Koul: "New support: - TI J721S2 CSI BCDMA support Updates: - Native HDMI support for dw edma driver - ste dma40 updates for supporting proper SRAM handle in DT - removal of dma device chancnt setting in drivers" * tag 'dmaengine-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (28 commits) dmaengine: sprd: Don't set chancnt dmaengine: hidma: Don't set chancnt dmaengine: plx_dma: Don't set chancnt dmaengine: axi-dmac: Don't set chancnt dmaengine: dw-axi-dmac: Don't set chancnt dmaengine: qcom: bam_dma: allow omitting num-{channels,ees} dmaengine: dw-edma: Add HDMA DebugFS support dmaengine: dw-edma: Add support for native HDMA dmaengine: dw-edma: Create a new dw_edma_core_ops structure to abstract controller operation dmaengine: dw-edma: Rename dw_edma_core_ops structure to dw_edma_plat_ops dmaengine: ste_dma40: use proper format string for resource_size_t dmaengine: make QCOM_HIDMA depend on HAS_IOMEM dmaengine: ste_dma40: fix typo in enum documentation dmaengine: ste_dma40: use correct print specfier for resource_size_t MAINTAINERS: Add myself as the DW eDMA driver reviewer MAINTAINERS: Add Manivannan to DW eDMA driver maintainers list MAINTAINERS: Demote Gustavo Pimentel to DW EDMA driver reviewer dmaengine: ti: k3-udma: Add support for J721S2 CSI BCDMA instance dt-bindings: dma: ti: Add J721S2 BCDMA dmaengine: ti: k3-psil-j721s2: Add PSI-L thread map for main CPSW2G ...
| * dmaengine: dw-edma: Rename dw_edma_core_ops structure to dw_edma_plat_opsCai Huoqing2023-05-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The dw_edma_core_ops structure contains a set of the operations: device IRQ numbers getter, CPU/PCI address translation. Based on the functions semantics the structure name "dw_edma_plat_ops" looks more descriptive since indeed the operations are platform-specific. The "dw_edma_core_ops" name shall be used for a structure with the IP-core specific set of callbacks in order to abstract out DW eDMA and DW HDMA setups. Such structure will be added in one of the next commit in the framework of the set of changes adding the DW HDMA device support. Anyway the renaming was necessary to distinguish two types of the implementation callbacks: 1. DW eDMA/hDMA IP-core specific operations: device-specific CSR setups in one or another aspect of the DMA-engine initialization. 2. DW eDMA/hDMA platform specific operations: the DMA device environment configs like IRQs, address translation, etc. Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Serge Semin <fancer.lancer@gmail.com> Link: https://lore.kernel.org/r/20230520050854.73160-2-cai.huoqing@linux.dev Signed-off-by: Vinod Koul <vkoul@kernel.org>
* | Merge tag 'pci-v6.5-changes' of ↵Linus Torvalds2023-06-3011-69/+197
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull pci updates from Bjorn Helgaas: "Enumeration: - Export pcie_retrain_link() for use outside ASPM - Add Data Link Layer Link Active Reporting as another way for pcie_retrain_link() to determine the link is up - Work around link training failures (especially on the ASMedia ASM2824 switch) by training first at 2.5GT/s and then attempting higher rates Resource management: - When we coalesce host bridge windows, remove invalidated resources from the resource tree so future allocations work correctly Hotplug: - Cancel bringup sequence if card is not present, to keep from blinking Power Indicator indefinitely - Reassign bridge resources if necessary for ACPI hotplug Driver binding: - Convert platform_device .remove() callbacks to return void instead of a mostly useless int Power management: - Reduce wait time for secondary bus to be ready to speed up resume - Avoid putting EloPOS E2/S2/H2 (as well as Elo i2) PCIe Ports in D3cold - Call _REG when transitioning D-states so AML that uses the PCI config space OpRegion works, which fixes some ASMedia GPIO controllers after resume Virtualization: - Delay extra 250ms after FLR of Solidigm P44 Pro NVMe to avoid KVM hang when guest is rebooted - Add function 1 DMA alias quirk for Marvell 88SE9235 Error handling: - Unexport pci_save_aer_state() since it's only used in drivers/pci/ - Drop recommendation for drivers to configure AER Capability, since the PCI core does this for all devices ASPM: - Disable ASPM on MFD function removal to avoid use-after-free - Tighten up pci_enable_link_state() and pci_disable_link_state() interfaces so they don't enable/disable states the driver didn't specify - Avoid link retraining race that can happen if ASPM sets link control parameters while the link is in the midst of training for some other reason Endpoint framework: - Change "PCI Endpoint Virtual NTB driver" Kconfig prompt to be different from "PCI Endpoint NTB driver" - Automatically create a function specific attributes group for endpoint drivers to avoid reference counting issues - Fix many EPC test issues - Return pci_epf_type_add_cfs() error if EPF has no driver - Add kernel-doc for pci_epc_raise_irq() and pci_epc_map_msi_irq() MSI vector parameters - Pass EPF device ID to driver probe functions - Return -EALREADY if EPC has already been started/stopped - Add linkdown notifier support and use it in qcom-ep - Add Bus Master Enable event support and use it in qcom-ep - Add Qualcomm Modem Host Interface (MHI) endpoint driver - Add Layerscape PME interrupt handling to manage link-up notification Cadence PCIe controller driver: - Wait for link retrain to complete when working around the J721E i2085 erratum with Gen2 mode Faraday FTPC100 PCI controller driver: - Release clock resources on error paths Freescale i.MX6 PCIe controller driver: - Save and restore Root Port MSI control to work around hardware defect Intel VMD host bridge driver: - Reset VMD config register between soft reboots - Capture pci_reset_bus() return value instead of printing junk when it fails Qualcomm PCIe controller driver: - Add SDX65 endpoint compatible string to DT binding - Disable register write access after init for IP v2.3.3, v2.9.0 - Use DWC helpers for enabling/disabling writes to DBI registers - Hide slot hotplug capability for IP v1.0.0, v1.9.0, v2.1.0, v2.3.2, v2.3.3, v2.7.0, v2.9.0 - Reuse v2.3.2 post-init sequence for v2.4.0 Renesas R-Car PCIe controller driver: - Remove unused static pcie_base and pcie_dev Rockchip PCIe controller driver: - Remove writes to unused registers - Write endpoint Device ID using correct register - Assert PCI Configuration Enable bit after probe so endpoint responds instead of generating Request Retry Status messages - Poll waiting for PHY PLLs to lock - Update RK3399 example DT binding to be valid - Use RK3399 PCIE_CLIENT_LEGACY_INT_CTRL to generate INTx instead of manually generating PCIe message - Use multiple windows to avoid address translation conflicts - Use u32 (not u16) when accessing 32-bit registers - Hide MSI-X Capability, since RK3399 can't generate MSI-X - Set endpoint controller required alignment to 256 Synopsys DesignWare PCIe controller driver: - Wait for link to come up only if we've initiated link training Miscellaneous: - Add pci_clear_master() stub for non-CONFIG_PCI" * tag 'pci-v6.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (116 commits) Documentation: PCI: correct spelling PCI: vmd: Fix uninitialized variable usage in vmd_enable_domain() PCI: xgene-msi: Convert to platform remove callback returning void PCI: tegra: Convert to platform remove callback returning void PCI: rockchip-host: Convert to platform remove callback returning void PCI: mvebu: Convert to platform remove callback returning void PCI: mt7621: Convert to platform remove callback returning void PCI: mediatek-gen3: Convert to platform remove callback returning void PCI: mediatek: Convert to platform remove callback returning void PCI: iproc: Convert to platform remove callback returning void PCI: hisi-error: Convert to platform remove callback returning void PCI: dwc: Convert to platform remove callback returning void PCI: j721e: Convert to platform remove callback returning void PCI: brcmstb: Convert to platform remove callback returning void PCI: altera-msi: Convert to platform remove callback returning void PCI: altera: Convert to platform remove callback returning void PCI: aardvark: Convert to platform remove callback returning void PCI: rcar: Use correct product family name for Renesas R-Car PCI: layerscape: Add the endpoint linkup notifier support PCI: endpoint: pci-epf-vntb: Fix typo in comments ...
| * \ Merge branch 'pci/controller/remove-void-callbacks'Bjorn Helgaas2023-06-265-22/+12
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Convert platform_device .remove() callbacks to return void instead of a mostly useless int (Uwe Kleine-König) * pci/controller/remove-void-callbacks: PCI: xgene-msi: Convert to platform remove callback returning void PCI: tegra: Convert to platform remove callback returning void PCI: rockchip-host: Convert to platform remove callback returning void PCI: mvebu: Convert to platform remove callback returning void PCI: mt7621: Convert to platform remove callback returning void PCI: mediatek-gen3: Convert to platform remove callback returning void PCI: mediatek: Convert to platform remove callback returning void PCI: iproc: Convert to platform remove callback returning void PCI: hisi-error: Convert to platform remove callback returning void PCI: dwc: Convert to platform remove callback returning void PCI: j721e: Convert to platform remove callback returning void PCI: brcmstb: Convert to platform remove callback returning void PCI: altera-msi: Convert to platform remove callback returning void PCI: altera: Convert to platform remove callback returning void PCI: aardvark: Convert to platform remove callback returning void
| | * | PCI: dwc: Convert to platform remove callback returning voidUwe Kleine-König2023-06-245-22/+12
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is (mostly) ignored and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Trivially convert the dwc drivers from always returning zero in the remove callback to the void returning variant. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20230321193208.366561-7-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Acked-by: Serge Semin <fancer.lancer@gmail.com>
| * | Merge branch 'pci/controller/endpoint'Bjorn Helgaas2023-06-262-1/+101
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Change "PCI Endpoint Virtual NTB driver" Kconfig prompt to be different from "PCI Endpoint NTB driver" (Shunsuke Mie) - Automatically create a function specific attributes group for endpoint drivers to avoid reference counting issues (Damien Le Moal) - Move and unexport pci_epf_type_add_cfs() (Damien Le Moal) - Reinitialize EPF test DMA transfer completion before submitting it to avoid losing the completion notification (Damien Le Moal) - Fix EPF test DMA transfer completion detection (Damien Le Moal) - Submit EPF test DMA transfers with dmaengine_submit(), not tx_submit() (Damien Le Moal) - Simplify EPF test read/write/copy functions (Damien Le Moal) - Simplify EPF test "raise IRQ" interface (Damien Le Moal) - Simplify EPF test IRQ command execution (Damien Le Moal) - Improve EPF test command/status register handling (Damien Le Moal) - Free IRQs before removing device (Damien Le Moal) - Reinitialize IRQ completions for every test (Damien Le Moal) - Don't write status in IRQ handler to avoid race (Damien Le Moal) - Fix dma_chan direction in data transfer test (Yoshihiro Shimoda) - Return pci_epf_type_add_cfs() error if EPF has no driver (Damien Le Moal) - Add kernel-doc for pci_epc_raise_irq() and pci_epc_map_msi_irq() MSI vector parameters (Manivannan Sadhasivam) - Pass EPF device ID to driver probe functions (Manivannan Sadhasivam) - Return -EALREADY if EPC has already been started/stopped (Manivannan Sadhasivam) - Add linkdown notifier support and use it in qcom-ep (Manivannan Sadhasivam) - Add Bus Master Enable event support and use it in qcom-ep (Manivannan Sadhasivam) - Add Qualcomm Modem Host Interface (MHI) endpoint driver (Manivannan Sadhasivam) - Add Layerscape PME interrupt handling to manage link-up notification (Frank Li) * pci/controller/endpoint: PCI: layerscape: Add the endpoint linkup notifier support PCI: endpoint: pci-epf-vntb: Fix typo in comments MAINTAINERS: Add PCI MHI endpoint function driver under MHI bus PCI: endpoint: Add PCI Endpoint function driver for MHI bus PCI: qcom-ep: Add support for BME notification PCI: qcom-ep: Add support for Link down notification PCI: endpoint: Add BME notifier support PCI: endpoint: Add linkdown notifier support PCI: endpoint: Return error if EPC is started/stopped multiple times PCI: endpoint: Pass EPF device ID to the probe function PCI: endpoint: Add missing documentation about the MSI/MSI-X range PCI: endpoint: Improve pci_epf_type_add_cfs() PCI: endpoint: functions/pci-epf-test: Fix dma_chan direction misc: pci_endpoint_test: Simplify pci_endpoint_test_msi_irq() misc: pci_endpoint_test: Do not write status in IRQ handler misc: pci_endpoint_test: Re-init completion for every test misc: pci_endpoint_test: Free IRQs before removing the device PCI: epf-test: Simplify transfers result print PCI: epf-test: Simplify DMA support checks PCI: epf-test: Cleanup request result handling PCI: epf-test: Cleanup pci_epf_test_cmd_handler() PCI: epf-test: Improve handling of command and status registers PCI: epf-test: Simplify IRQ test commands execution PCI: epf-test: Simplify pci_epf_test_raise_irq() PCI: epf-test: Simplify read/write/copy test functions PCI: epf-test: Use dmaengine_submit() to initiate DMA transfer PCI: epf-test: Fix DMA transfer completion detection PCI: epf-test: Fix DMA transfer completion initialization PCI: endpoint: Move pci_epf_type_add_cfs() code PCI: endpoint: Automatically create a function specific attributes group PCI: endpoint: Fix a Kconfig prompt of vNTB driver
| | * | PCI: layerscape: Add the endpoint linkup notifier supportFrank Li2023-06-231-1/+99
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Layerscape has PME interrupt, which can be used as linkup notifier. Set CFG_READY bit of PEX_PF0_CONFIG to enable accesses from root complex when linkup detected. Link: https://lore.kernel.org/r/20230515151049.2797105-1-Frank.Li@nxp.com Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
| | * | PCI: qcom-ep: Add support for BME notificationManivannan Sadhasivam2023-06-231-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support to pass BME (Bus Master Enable) notification to Endpoint function driver so that the BME event can be processed by the function. Link: https://lore.kernel.org/r/20230602114756.36586-8-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org> Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
| | * | PCI: qcom-ep: Add support for Link down notificationManivannan Sadhasivam2023-06-231-0/+1
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support to pass Link down notification to Endpoint function driver so that the LINK_DOWN event can be processed by the function. Link: https://lore.kernel.org/r/20230602114756.36586-7-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org> Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
| * | Merge branch 'pci/controller/qcom'Bjorn Helgaas2023-06-261-35/+38
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Disable register write access after init for IP v2.3.3, v2.9.0 (Manivannan Sadhasivam) - Use DWC helpers for enabling/disabling writes to DBI registers (Manivannan Sadhasivam) - Hide slot hotplug capability for IP v1.0.0, v1.9.0, v2.1.0, v2.3.2, v2.3.3, v2.7.0, v2.9.0 (Manivannan Sadhasivam) - Reuse v2.3.2 post-init sequence for v2.4.0 (Manivannan Sadhasivam) - * pci/controller/qcom: PCI: qcom: Do not advertise hotplug capability for IP v2.1.0 PCI: qcom: Do not advertise hotplug capability for IP v1.0.0 PCI: qcom: Use post init sequence of IP v2.3.2 for v2.4.0 PCI: qcom: Do not advertise hotplug capability for IP v2.3.2 PCI: qcom: Do not advertise hotplug capability for IPs v2.3.3 and v2.9.0 PCI: qcom: Do not advertise hotplug capability for IPs v2.7.0 and v1.9.0 PCI: qcom: Disable write access to read only registers for IP v2.9.0 PCI: qcom: Use DWC helpers for modifying the read-only DBI registers PCI: qcom: Disable write access to read only registers for IP v2.3.3
| | * | PCI: qcom: Do not advertise hotplug capability for IP v2.1.0Manivannan Sadhasivam2023-06-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoCs making use of Qcom PCIe controller IP v2.1.0 do not support hotplug functionality. But the hotplug capability bit is set by default in the hardware. This causes the kernel PCI core to register hotplug service for the controller and send hotplug commands to it. But those commands will timeout generating messages as below during boot and suspend/resume. [ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago) [ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago) [ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago) [ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago) This not only spams the console output but also induces a delay of a couple of seconds. To fix this issue, let's clear the HPC bit in PCI_EXP_SLTCAP register as a part of the post init sequence to not advertise the hotplug capability for the controller. Link: https://lore.kernel.org/r/20230619150408.8468-10-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
| | * | PCI: qcom: Do not advertise hotplug capability for IP v1.0.0Manivannan Sadhasivam2023-06-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoCs making use of Qcom PCIe controller IP v1.0.0 do not support hotplug functionality. But the hotplug capability bit is set by default in the hardware. This causes the kernel PCI core to register hotplug service for the controller and send hotplug commands to it. But those commands will timeout generating messages as below during boot and suspend/resume. [ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago) [ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago) [ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago) [ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago) This not only spams the console output but also induces a delay of a couple of seconds. To fix this issue, let's clear the HPC bit in PCI_EXP_SLTCAP register as a part of the post init sequence to not advertise the hotplug capability for the controller. Link: https://lore.kernel.org/r/20230619150408.8468-9-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
| | * | PCI: qcom: Use post init sequence of IP v2.3.2 for v2.4.0Manivannan Sadhasivam2023-06-201-29/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The post init sequence of IP v2.4.0 is same as v2.3.2. So let's reuse the v2.3.2 sequence which now also disables hotplug capability of the controller as it is not at all supported on any SoCs making use of this IP. Link: https://lore.kernel.org/r/20230619150408.8468-8-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
| | * | PCI: qcom: Do not advertise hotplug capability for IP v2.3.2Manivannan Sadhasivam2023-06-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoCs making use of Qcom PCIe controller IP v2.3.2 do not support hotplug functionality. But the hotplug capability bit is set by default in the hardware. This causes the kernel PCI core to register hotplug service for the controller and send hotplug commands to it. But those commands will timeout generating messages as below during boot and suspend/resume. [ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago) [ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago) [ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago) [ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago) This not only spams the console output but also induces a delay of a couple of seconds. To fix this issue, let's clear the HPC bit in PCI_EXP_SLTCAP register as a part of the post init sequence to not advertise the hotplug capability for the controller. Link: https://lore.kernel.org/r/20230619150408.8468-7-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
generated by cgit v1.2.3 (git 2.46.0) at 2025-04-30 05:29:14 +0000