| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If a hotplug port is able to send an interrupt, one would naively assume
that it is accessible at that moment. After all, if it wouldn't be
accessible, i.e. if its parent is in D3hot and the link to the hotplug
port is thus down, how should an interrupt come through?
It turns out that assumption is wrong at least for Thunderbolt: Even
though its parents are in D3hot, a Thunderbolt hotplug port is able to
signal interrupts. Because the port's config space is inaccessible and
resuming the parents may sleep, the hard IRQ handler has to defer
runtime resuming the parents and reading the Slot Status register to the
IRQ thread.
If the hotplug port uses a level-triggered INTx interrupt, it needs to
be masked until the IRQ thread has cleared the signaled events. For
simplicity, this commit also masks edge-triggered MSI/MSI-X interrupts.
Note that if the interrupt is shared (which can only happen for INTx),
other devices are starved from receiving interrupts until the IRQ thread
is scheduled, has runtime resumed the hotplug port's parents and has
read and cleared the Slot Status register.
That delay is dominated by the 10 ms D3hot->D0 transition time of each
parent port. The worst case is a Thunderbolt downstream port at the
end of a daisy chain: There may be up to six Thunderbolt controllers
in-between it and the root port, each comprising an upstream and
downstream port, plus its own upstream port. That's 13 x 10 = 130 ms.
Possible mitigations are polling the interrupt while it's disabled or
reducing the d3_delay of Thunderbolt ports if possible.
Open code masking of the interrupt instead of requesting it with the
IRQF_ONESHOT flag to minimize the period during which it is masked.
(IRQF_ONESHOT unmasks the IRQ only after the IRQ thread has finished.)
PCIe r4.0 sec 6.7.3.4 states that "If wake generation is required by the
associated form factor specification, a hotplug capable Downstream Port
must support generation of a wakeup event (using the PME mechanism) on
hotplug events that occur when the system is in a sleep state or the
Port is in device state D1, D2, or D3Hot."
This would seem to imply that PME needs to be enabled on the hotplug
port when it is runtime suspended. pci_enable_wake() currently doesn't
enable PME on bridges, it may be necessary to add an exemption for
hotplug bridges there. On "Light Ridge" Thunderbolt controllers, the
PME_Status bit is not set when an interrupt occurs while the hotplug
port is in D3hot, even if PME is enabled. (I've tested this on a Mac
and we hardcode the OSC_PCI_EXPRESS_PME_CONTROL bit to 0 on Macs in
negotiate_os_control(), modifying it to 1 didn't change the behavior.)
(Side note: Section 6.7.3.4 also states that "PME and Hot-Plug Event
interrupts (when both are implemented) always share the same MSI or
MSI-X vector". That would only seem to apply to Root Ports, however
the section never mentions Root Ports, only Downstream Ports. This is
explained in the definition of "Downstream Port" in the "Terms and
Acronyms" section of the PCIe Base Spec: "The Ports on a Switch that
are not the Upstream Port are Downstream Ports. All Ports on a Root
Complex are Downstream Ports.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840feab ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ->reset_slot callback introduced by commits:
2e35afaefe64 ("PCI: pciehp: Add reset_slot() method") and
06a8d89af551 ("PCI: pciehp: Disable link notification across slot reset")
disables notification of Presence Detect Changed and Data Link Layer
State Changed events for the duration of a secondary bus reset.
However a bus reset not only triggers these events, but may also clear
the Presence Detect State bit in the Slot Status register and the Data
Link Layer Link Active bit in the Link Status register momentarily.
According to Sinan Kaya:
"I know for a fact that bus reset clears the Data Link Layer Active bit
as soon as link goes down. It gets set again following link up.
Presence detect depends on the HW implementation. QDT root ports
don't change presence detect for instance since nobody actually
removed the card. If an implementation supports in-band presence
detect, the answer is yes. As soon as the link goes down, presence
detect bit will get cleared until recovery."
https://lkml.kernel.org/r/42e72f83-3b24-f7ef-e5bc-290fae99259a@codeaurora.org
In-band presence detect is also covered in Table 4-15 in PCIe r4.0,
sec 4.2.6.
pciehp should therefore ensure that any parts of the driver that access
those bits do not run concurrently to a bus reset. The only precaution
the commits took to that effect was to halt interrupt polling. They
made no effort to drain the slot workqueue, cancel an outstanding
Attention Button work, or block slot enable/disable requests via sysfs
and in the ->probe hook.
Now that pciehp is converted to enable/disable the slot exclusively from
the IRQ thread, the only places accessing the two above-mentioned bits
are the IRQ thread and the ->probe hook. Add locking to serialize them
with a bus reset. This obviates the need to halt interrupt polling.
Do not add locking to the ->get_adapter_status sysfs callback to afford
users unfettered access to that bit. Use an rw_semaphore in lieu of a
regular mutex to allow parallel execution of the non-reset code paths
accessing the critical bits, i.e. the IRQ thread and the ->probe hook.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Sinan Kaya <okaya@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A hotplug port's Slot Status register does not count how often each type
of event occurred, it only records the fact *that* an event has occurred.
Previously pciehp queued a work item for each event. But if it missed
an event, e.g. removal of a card in-between two back-to-back insertions,
it queued up the wrong work item or no work item at all. Commit
fad214b0aa72 ("PCI: pciehp: Process all hotplug events before looking
for new ones") sought to improve the situation by shrinking the window
during which events may be missed.
But Stefan Roese reports unbalanced Card present and Link Up events,
suggesting that we're still missing events if they occur very rapidly.
Bjorn Helgaas responds that he considers pciehp's event handling
"baroque" and calls for its simplification and rationalization:
https://lkml.kernel.org/r/20180202192045.GA53759@bhelgaas-glaptop.roam.corp.google.com
It gets worse once a hotplug port is runtime suspended: The port can
signal an interrupt while it and its parents are in D3hot, i.e. while
it is inaccessible. By the time we've runtime resumed all parents to D0
and read the port's Slot Status register, we may have missed an arbitrary
number of events. Event handling therefore needs to be reworked to
become resilient to missed events.
Assume that a Presence Detect Changed event has occurred.
Consider the following truth table:
- Slot is in OFF_STATE and is currently empty. => Do nothing.
(The event is trailing a Link Down or we've
missed an insertion and subsequent removal.)
- Slot is in OFF_STATE and is currently occupied. => Turn the slot on.
- Slot is in ON_STATE and is currently empty. => Turn the slot off.
- Slot is in ON_STATE and is currently occupied. => Turn the slot off,
(Be cautious and assume the card in then back on.
the slot isn't the same as before.)
This leads to the following simple algorithm:
1 If the slot is in ON_STATE, turn it off unconditionally.
2 If the slot is currently occupied, turn it on.
Because those actions are now carried out synchronously, rather than by
scheduled work items, pciehp reacts to the *current* situation and
missed events no longer matter.
Data Link Layer State Changed events can be handled identically to
Presence Detect Changed events. Note that in the above truth table,
a Link Up trailing a Card present event didn't have to be accounted for:
It is filtered out by pciehp_check_link_status().
As for Attention Button Pressed events, PCIe r4.0, sec 6.7.1.5 says:
"Once the Power Indicator begins blinking, a 5-second abort interval
exists during which a second depression of the Attention Button cancels
the operation." In other words, the user can only expect the system to
react to a button press after it starts blinking. Missed button presses
that occur in-between are irrelevant.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
|
| |
|
|
|
|
|
|
|
|
| |
No callers of pciehp_enable/disable_slot() outside of pciehp_ctrl.c
remain, so declare the functions static. For now this requires forward
declarations. Those can be eliminated by reshuffling functions once the
ongoing effort to refactor the driver has settled.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
| |
Previously slot enablement and disablement could happen concurrently.
But now it's under the exclusive control of the IRQ thread, rendering
the locking obsolete. Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Besides the IRQ thread, there are several other places in the driver
which enable or disable the slot:
- pciehp_probe() enables the slot if it's occupied and the pciehp_force
module parameter is used.
- pciehp_resume() enables or disables the slot after system sleep.
- pciehp_queue_pushbutton_work() enables or disables the slot after the
5 second delay following an Attention Button press.
- pciehp_sysfs_enable_slot() and pciehp_sysfs_disable_slot() enable or
disable the slot on sysfs write.
This requires locking and complicates pciehp's state machine.
A simplification can be achieved by enabling and disabling the slot
exclusively from the IRQ thread.
Amend the functions listed above to request slot enable/disablement from
the IRQ thread by either synthesizing a Presence Detect Changed event or,
in the case of a disable user request (via sysfs or an Attention Button
press), submitting a newly introduced force disable request. The latter
is needed because the slot shall be forced off despite being occupied.
For this force disable request, avoid colliding with Slot Status register
bits by using a bit number greater than 16.
For synchronous execution of requests (on sysfs write), wait for the
request to finish and retrieve the result. There can only ever be one
sysfs write in flight due to the locking in kernfs_fop_write(), hence
there is no risk of returning the result of a different sysfs request to
user space.
The POWERON_STATE and POWEROFF_STATE is now no longer entered by the
above-listed functions, but solely by the IRQ thread when it begins a
power transition. Afterwards, it moves to STATIC_STATE. The same
applies to canceling the Attention Button work, it likewise becomes an
IRQ thread only operation.
An immediate consequence is that the POWERON_STATE and POWEROFF_STATE is
never observed by the IRQ thread itself, only by functions called in a
different context, such as pciehp_sysfs_enable_slot(). So remove
handling of these states from pciehp_handle_button_press() and
pciehp_handle_link_change() which are exclusively called from the IRQ
thread.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
handle_button_press_event() currently determines whether the slot has
been turned on or off by looking at the Power Controller Control bit in
the Slot Control register. This assumes that an attention button
implies presence of a power controller even though that's not mandated
by the spec. Moreover the Power Controller Control bit is unreliable
when a power fault occurs (PCIe r4.0, sec 6.7.1.8). This issue has
existed since the driver was introduced in 2004.
Fix by replacing STATIC_STATE with ON_STATE and OFF_STATE and tracking
whether the slot has been turned on or off. This is also a required
ingredient to make pciehp resilient to missed events, which is the
object of an upcoming commit.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Previously the slot workqueue was used to handle events and enable or
disable the slot. That's no longer the case as those tasks are done
synchronously in the IRQ thread. The slot workqueue is thus merely used
to handle a button press after the 5 second delay and only one such work
item may be in flight at any given time. A separate workqueue isn't
necessary for this simple task, so use the system workqueue instead.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Up until now, pciehp's IRQ handler schedules a work item for each event,
which in turn schedules a work item to enable or disable the slot. This
double indirection was necessary because sleeping wasn't allowed in the
IRQ handler.
However it is now that pciehp has been converted to threaded IRQ handling
and polling, so handle events synchronously in pciehp_ist() and remove
the work item infrastructure (with the exception of work items to handle
a button press after the 5 second delay).
For link or presence change events, move the register read to determine
the current link or presence state behind acquisition of the slot lock
to prevent it from becoming stale while the lock is contended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
We've just converted pciehp to threaded IRQ handling, but still cannot
sleep in pciehp_ist() because the function is also called in poll mode,
which runs in softirq context (from a timer).
Convert poll mode to a kthread so that pciehp_ist() always runs in task
context.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
pciehp's IRQ handler queues up a work item for each event signaled by
the hardware. A more modern alternative is to let a long running
kthread service the events. The IRQ handler's sole job is then to check
whether the IRQ originated from the device in question, acknowledge its
receipt to the hardware to quiesce the interrupt and wake up the kthread.
One benefit is reduced latency to handle the IRQ, which is a necessity
for realtime environments. Another benefit is that we can make pciehp
simpler and more robust by handling events synchronously in process
context, rather than asynchronously by queueing up work items. pciehp's
usage of work items is a historic artifact, it predates the introduction
of threaded IRQ handlers by two years. (The former was introduced in
2007 with commit 5d386e1ac402 ("pciehp: Event handling rework"), the
latter in 2009 with commit 3aa551c9b4c4 ("genirq: add threaded interrupt
handler support").)
Convert pciehp to threaded IRQ handling by retrieving the pending events
in pciehp_isr(), saving them for later consumption by the thread handler
pciehp_ist() and clearing them in the Slot Status register.
By clearing the Slot Status (and thereby acknowledging the events) in
pciehp_isr(), we can avoid requesting the IRQ with IRQF_ONESHOT, which
would have the unpleasant side effect of starving devices sharing the
IRQ until pciehp_ist() has finished.
pciehp_isr() does not count how many times each event occurred, but
merely records the fact *that* an event occurred. If the same event
occurs a second time before pciehp_ist() is woken, that second event
will not be recorded separately, which is problematic according to
commit fad214b0aa72 ("PCI: pciehp: Process all hotplug events before
looking for new ones") because we may miss removal of a card in-between
two back-to-back insertions. We're about to make pciehp_ist() resilient
to missed events. The present commit regresses the driver's behavior
temporarily in order to separate the changes into reviewable chunks.
This doesn't affect regular slow-motion hotplug, only plug-unplug-plug
operations that happen in a timespan shorter than wakeup of the IRQ
thread.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
|
| |
|
|
|
|
|
|
| |
Document the driver's data structures to lower the barrier to entry for
contributors.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Since commit 0f4bd8014db5 ("PCI: hotplug: Drop checking of PCI_BRIDGE_
CONTROL in *_unconfigure_device()"), pciehp_unconfigure_device() can no
longer fail, so declare it and its sole caller remove_board() void, in
keeping with the usual kernel pattern that enablement can fail, but
disablement cannot. No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When pciehp is unbound (e.g. on unplug of a Thunderbolt device), the
hotplug_slot struct is deregistered and thus freed before freeing the
IRQ. The IRQ handler and the work items it schedules print the slot
name referenced from the freed structure in various informational and
debug log messages, each time resulting in a quadruple dereference of
freed pointers (hotplug_slot -> pci_slot -> kobject -> name).
At best the slot name is logged as "(null)", at worst kernel memory is
exposed in logs or the driver crashes:
pciehp 0000:10:00.0:pcie204: Slot((null)): Card not present
An attacker may provoke the bug by unplugging multiple devices on a
Thunderbolt daisy chain at once. Unplugging can also be simulated by
powering down slots via sysfs. The bug is particularly easy to trigger
in poll mode.
It has been present since the driver's introduction in 2004:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Fix by rearranging teardown such that the IRQ is freed first. Run the
work items queued by the IRQ handler to completion before freeing the
hotplug_slot struct by draining the work queue from the ->release_slot
callback which is invoked by pci_hp_deregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.4
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After a suspend/resume cycle the Presence Detect or Data Link Layer Status
Changed bits might be set. If we don't clear them those events will not
fire anymore and nothing happens for instance when a device is now
hot-unplugged.
Fix this by clearing those bits in a newly introduced function
pcie_reenable_notification(). This should be fine because immediately
after, we check if the adapter is still present by reading directly from
the status register.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
pcieport_if.h contained the interfaces to register port service driver,
e.g., pcie_port_service_register(). portdrv.h contained internal data
structures of the port driver.
I don't think it's worth keeping those files separate, since both headers
and their users are all inside the PCI core.
Merge pcieport_if.h directly in drivers/pci/pcie/portdrv.h and update the
users to include that instead.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
| |
|
|
|
|
|
|
|
|
| |
Move pcieport_if.h from include/linux to drivers/pci/pcie/pcieport_if.h
because the interfaces there are only used by the PCI core.
Replace all uses of #include<linux/pcieport_if.h> with relative paths to
the new file location, e.g., #include "../pcieport_if.h"
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Add SPDX GPL-2.0+ to all PCI files that specified the GPL and allowed
either GPL version 2 or any later version.
Remove the boilerplate GPL version 2 or later language, relying on the
assertion in b24413180f56 ("License cleanup: add SPDX GPL-2.0 license
identifier to files with no license") that the SPDX identifier may be used
instead of the full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
<linux/sched.h> into <linux/sched/signal.h>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
PCIe hotplug supports optional Attention and Power Indicators, which are
used internally by pciehp. Users can't control the Power Indicator, but
they can control the Attention Indicator by writing to a sysfs "attention"
file.
The Slot Control register has two bits for each indicator, and the PCIe
spec defines the encodings for each as (Reserved/On/Blinking/Off). For
sysfs "attention" writes, pciehp_set_attention_status() maps into these
encodings, so the only useful write values are 0 (Off), 1 (On), and 2
(Blinking).
However, some platforms use all four bits for platform-specific indicators,
and they need to allow direct user control of them while preventing pciehp
from using them at all.
Add a "hotplug_user_indicators" flag to the pci_dev structure. When set,
pciehp does not use either the Attention Indicator or the Power Indicator,
and the low four bits (values 0x0 - 0xf) of sysfs "attention" write values
are written directly to the Attention Indicator Control and Power Indicator
Control fields.
[bhelgaas: changelog, rename flag and accessors to s/attention/indicator/]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
| |
Fix all whitespace issues (missing or needed whitespace) in all files in
drivers/pci. Code is compiled with allyesconfig before and after code
changes and objects are recorded and checked with objdiff and they are not
changed after this commit.
Signed-off-by: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
| |
We queued interrupt events for the MRL being opened or closed, but the code
in interrupt_event_handler() that handles these events ignored them.
Stop enabling MRL interrupts and remove the ignored events.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
| |
The list of interrupt events (INT_BUTTON_IGNORE, INT_PRESENCE_ON, etc.) was
copied from other hotplug drivers, but pciehp doesn't use them all.
Remove the interrupt events that aren't used by pciehp.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
The pciehp_handle_*() functions (pciehp_handle_attention_button(), etc.)
only contain a line or two of useful code, so it's clumsy to put
them in separate functions. All they so is add an event to a work queue,
and it's clearer to see that directly in the ISR.
Inline them directly into pcie_isr(). No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Jarod Wilson reports that ExpressCard hotplug doesn't work on HP ZBook G2.
The problem turns out to be the ACPI-based "slot detection" code called
from pciehp_probe() which uses questionable heuristics based on what ACPI
objects are present for the PCIe port device to figure out whether to
register a hotplug slot for that port.
That code is used if there is at least one PCIe port having an ACPI device
configuration object related to hotplug (such as _EJ0 or _RMV), and the
Thunderbolt port on the ZBook has _RMV. Of course, Thunderbolt and PCIe
native hotplug need not be mutually exclusive (as they aren't on the
ZBook), so that rule is simply incorrect.
Moreover, the ACPI-based "slot detection" check does not add any value if
pciehp_probe() is called at all and the service type of the device object
it has been called for is PCIE_PORT_SERVICE_HP, because PCIe hotplug
services are only registered if the _OSC handshake in acpi_pci_root_add()
allows the kernel to control the PCIe native hotplug feature. No more
checks need to be carried out to decide whether or not to register a native
PCIe hotlug slot in that case.
For the above reasons, make pciehp_probe() check if it has been called for
the right service type and drop the pointless ACPI-based "slot detection"
check from it. Also remove the entire code whose only user is that check
(the entire pciehp_acpi.c file goes away as a result) and drop function
headers related to it from the internal pciehp header file.
Link: http://lkml.kernel.org/r/1431632038-39917-1-git-send-email-jarod@redhat.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=98581
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
4283c70e91dc ("PCI: pciehp: Make pcie_wait_cmd() self-contained") added
a cache of the most recent command written to the Slot Control register.
This register is only 16 bits wide, but the cache ("slot_ctrl") is 32 bits.
Reduce slot_ctrl to a u16 so it matches the register size. No functional
change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
"no_cmd_complete" is only used once, and it duplicates read-only
information we already have in the cached Slot Capabilities value.
Remove the field and use the existing macro NO_CMD_CMPL() instead.
[bhelgaas: changelog]
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If we issue a hotplug command, go do something else, then come back and
wait for the command to complete, we don't have to wait the whole timeout
period, because some of it elapsed while we were doing something else.
Keep track of the time we issued the command, and wait only until the
timeout period from that point has elapsed.
For controllers with errata like Intel CF118, we previously timed out
before issuing the second hotplug command:
At time T1 (during boot):
- Write DLLSCE, ABPE, PDCE, etc. to Slot Control
At time T2 (hotplug event):
- Wait for command completion (CC) in Slot Status
- Timeout at T2 + 1 second because CC is never set in Slot Status
- Write PCC, PIC, etc. to Slot Control
With this change, we wait until T1 + 1 second instead of T2 + 1 second.
If the hotplug event is more than 1 second after the boot-time
initialization, we won't wait for the timeout at all.
We still emit a "Timeout on hotplug command" message if it timed out; we
should see this on the first hotplug event on every controller with this
erratum, as well as on real errors on controllers without the erratum.
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e7-v2-spec-update.html
Tested-by: Rajat Jain <rajatxjain@gmail.com> (IDT 807a controller)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
pcie_wait_cmd() waits for the controller to finish a hotplug command. Move
the associated logic (to determine whether waiting is required and whether
we're using interrupts or polling) from pcie_write_cmd() to
pcie_wait_cmd().
No functional change.
Tested-by: Rajat Jain <rajatxjain@gmail.com> (IDT 807a controller)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
| |
|
|
|
|
|
|
|
| |
Use PCI_EXP_SLTCAP_PSN to make it easier to find code that uses the
Physical Slot Number field in the PCIe Slot Capabilities register.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Today it is there is no protection around pciehp_enable_slot() and
pciehp_disable_slot() to ensure that they complete before another
hot-plug operation can be done on that particular slot.
This patch introduces the slot->hotplug_lock to ensure that any hotplug
operations (add / remove) complete before another hotplug event can begin
processing on that particular slot.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A lot of systems do not have the fancy buttons and LEDs, and instead
want to rely only on the Link state change events to drive the hotplug
and removal state machinery.
(http://www.spinics.net/lists/hotplug/msg05802.html)
This patch adds support for that functionality. Here are the details
about the patch itself:
* Define and use interrupt events for linkup / linkdown.
* Make the pcie_isr() also look at link events, and direct control to
corresponding (new) link state change handler function.
* Introduce the functions to handle link-up and link-down events and
queue the add / removal work in the slot->wq to be processed by
pciehp_power_thread()
As a side note, this patch also fixes the bug
https://bugzilla.kernel.org/show_bug.cgi?id=65521 "pciehp ignores Data Link
Layer State Changed bit."
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
check_link_active() functionality needs to be used by subsequent patches
(that introduce link state change based hotplug). Thus make the function
non-static, and rename it to pciehp_check_link_active() so as to be
consistent with other non-static functions.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* pci/dead-code:
PCI: Make local functions static
PCI: Remove unused alloc_pci_dev()
PCI: Remove unused pci_renumber_slot()
PCI: Remove unused pcie_aspm_enabled()
PCI: Remove unused pci_vpd_truncate()
PCI: Remove unused ID-Based Ordering support
PCI: Remove unused Optimized Buffer Flush/Fill support
PCI: Remove unused Latency Tolerance Reporting support
PCI: Removed unused parts of Page Request Interface support
Conflicts:
drivers/pci/pci.c
include/linux/pci.h
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Using 'make namespacecheck' identify code which should be declared static.
Checked for users in other driver/archs as well. Compile tested only.
This stops exporting the following interfaces to modules:
pci_target_state()
pci_load_saved_state()
[bhelgaas: retained pci_find_next_ext_capability() and pci_cfg_space_size()]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
These functions:
pcie_enable_notification()
pciehp_power_off_slot()
pciehp_get_power_status()
pciehp_get_attention_status()
pciehp_set_attention_status()
pciehp_get_latch_status()
pciehp_get_adapter_status()
pcie_write_cmd()
now always return success, so this patch makes them void and drops the
error-checking code in their callers.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
| |
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
PCIe hotplug has a bus per slot, so we can just use a normal
secondary bus reset. However, if a slot supports surprise removal,
a bus reset can be seen as a presence detection change triggering
a hot-remove followed by a hot-add. Disable presence detection from
triggering an interrupt or being polled around the bus reset.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
| |
We had an inconsistent mix of using and omitting the "extern" keyword
on function declarations in header files. This removes them all.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When we have a hotplug-capable PCIe port with a second hotplug-capable
PCIe port below it, removing the device below the upstream port causes
a deadlock.
The deadlock happens because we use the pciehp_wq workqueue to run
pciehp_power_thread(), which uses pciehp_disable_slot() to remove devices
below the upstream port. When we remove the downstream PCIe port, we call
pciehp_remove(), the pciehp driver's .remove() method. That calls
flush_workqueue(pciehp_wq), which deadlocks because the
pciehp_power_thread() work item is still running.
This patch avoids the deadlock by creating a workqueue for every PCIe port
and removing the single shared workqueue.
Here's the call path that leads to the deadlock:
pciehp_queue_pushbutton_work
queue_work(pciehp_wq) # queue pciehp_power_thread
...
pciehp_power_thread
pciehp_disable_slot
remove_board
pciehp_unconfigure_device
pci_stop_and_remove_bus_device
...
pciehp_remove # pciehp driver .remove method
pciehp_release_ctrl
pcie_cleanup_slot
flush_workqueue(pciehp_wq)
This is fairly urgent because it can be caused by simply unplugging a
Thunderbolt adapter, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2ssiRgcTD1bej2tkUUfsWmpL5eNtPcNif9va2-Gzb2u8nQ@mail.gmail.com
Reported-and-tested-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
|
| |
|
|
|
|
|
| |
pciehp_get_cur_lnk_width()
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
| |
|
|
|
|
|
|
|
|
|
| |
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in pciehp as a result.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
* Rename pciehp_wq to pciehp_ordered_wq and add non-ordered pciehp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both pciehp_wq and pciehp_ordered_wq upfront.
* Include workqueue.h from pciehp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
| |
|
|
|
|
|
|
| |
One of the recent changes caused complilation of
drivers/pci/hotplug/pciehp_core.c to fail. Fix this issue.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
After commit 852972acff8f10f3a15679be2059bb94916cba5d (ACPI: Disable
ASPM if the platform won't provide _OSC control for PCIe) control of
the PCIe Capability Structure is unconditionally requested by
acpi_pci_root_add(), which in principle may cause problems to
happen in two ways. First, the BIOS may refuse to give control of
the PCIe Capability Structure if it is not asked for any of the
_OSC features depending on it at the same time. Second, the BIOS may
assume that control of the _OSC features depending on the PCIe
Capability Structure will be requested in the future and may behave
incorrectly if that doesn't happen. For this reason, control of
the PCIe Capability Structure should always be requested along with
control of any other _OSC features that may depend on it (ie. PCIe
native PME, PCIe native hot-plug, PCIe AER).
Rework the PCIe port driver so that (1) it checks which native PCIe
port services can be enabled, according to the BIOS, and (2) it
requests control of all these services simultaneously. In
particular, this causes pcie_portdrv_probe() to fail if the BIOS
refuses to grant control of the PCIe Capability Structure, which
means that no native PCIe port services can be enabled for the PCIe
Root Complex the given port belongs to. If that happens, ASPM is
disabled to avoid problems with mishandling it by the part of the
PCIe hierarchy for which control of the PCIe Capability Structure
has not been received.
Make it possible to override this behavior using 'pcie_ports=native'
(use the PCIe native services regardless of the BIOS response to the
control request), or 'pcie_ports=compat' (do not use the PCIe native
services at all).
Accordingly, rework the existing PCIe port service drivers so that
they don't request control of the services directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
| |
|
|
|
|
|
|
|
|
|
| |
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in pciehp driver. This avoids unnecessary search in PCI
configuration space. This patch also removes 'cap_base' field in
struct controller, that was used to hold PCIe capability offset by
pciehp itself.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
