summaryrefslogtreecommitdiffstats
path: root/drivers/pci/hotplug/pciehp_hpc.c
Commit message (Collapse)AuthorAgeFilesLines
* PCI: pciehp: remove unused pciehp_get_max_lnk_width(), ↵Yinghai Lu2012-07-121-101/+0
| | | | | | | pciehp_get_cur_lnk_width() Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
* PCI: pciehp: Disable/enable link during slot power off/onYinghai Lu2012-02-141-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | On a system with a repeater on the system board to support gen2 hotplug, we found that when an ExpressModule is removed from some slots, /var/log/messages will be full of "card present/not present" warnings. It turns out the root complex is continually trying to train the link to the repeater because the repeater has not been reset. This patch will disable the link at removal time to allow the repeater to be reset properly. This also prevents a potential AER message at removal time. Also, when testing hotplug on a system under development, we found if we boot the system without an EM installed, and later hot-add an EM, it does not work with Linux, but another OS is ok. The root cause is that BIOS left link disabled when slot was empty at boot time, and other OS is modifying the link disable bit in link ctrl during power on/off. So we should do the same thing to disable/enable link during power off/on. -v2: check link DLLA bit instead of 100ms waiting. Separate link disable/enable functions to another patch. Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: Add Disable/enable link functionsYinghai Lu2012-02-141-0/+36
| | | | | | | Will use it during power off/on of slots Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: Add pcie_wait_link_not_active()Yinghai Lu2012-02-141-4/+15
| | | | | | | Will use it for link disable status checking. Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: make check_link_active more helpfulYinghai Lu2012-02-141-5/+12
| | | | | | | | | | A few changes: - remove the 'inline' and let the complier decide - return a bool to indicate whether the link was active - add a debug message to indicate link state when it beocmes active Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: replace unconditional sleep with config space access checkYinghai Lu2012-02-141-15/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | During reviewing | PCI: pciehp: wait 1000 ms before Link Training check Linus said: >... > That's a *long* time, and it's irritating to the user. It makes the > user think "the machine is slow". >... > And quite frankly, an unconditional one-second delay here seems bad. >Two seconds was unacceptable, one second is just bad. Try to access the pci conf of a pci device that is supposed to show up in 1s. If we can read back a valid vendor/device id, we can return early. Related discussion could be found: https://lkml.org/lkml/2011/12/6/339 -v2: seperate code to pci_bus_read_dev_vendor_id() from pci_scan_device() and reuse it from pciehp code. Suggested by Matthew Wilcox. -v3: According to Kenj, don't use array in stack, and don't wait too long for crs, also return fail status if not found. Also separate pci_bus_dev_read_vendor_id() change to another patch. Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: Handle push button event asynchronouslyKenji Kaneshige2011-12-051-1/+0
| | | | | | | | | | | Use non-ordered workqueue for attention button events. Attention button events on each slot can be handled asynchronously. So we should use non-ordered workqueue. This patch also removes ordered workqueue in pciehp as a result. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: wait 100 ms after Link Training checkKenji Kaneshige2011-11-111-0/+8
| | | | | | | | | | | If the port supports Link speeds greater than 5.0 GT/s, we must wait for 100 ms after Link training completes before sending configuration request. Acked-by: Yinghai Lu <yinghai@kernel.org> Tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: wait 1000 ms before Link Training checkKenji Kaneshige2011-11-111-0/+8
| | | | | | | | | | | | | We need to wait for 1000 ms after Data Link Layer Link Active (DLLLA) bit reads 1b before sending configuration request. Currently pciehp does this wait after checking Link Training (LT) bit. But we need it before checking LT bit because LT is still set even after DLLLA bit is set on some platforms. Acked-by: Yinghai Lu <yinghai@kernel.org> Tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: Retrieve link speed after link is trainedYinghai Lu2011-11-071-9/+2
| | | | | | | | | | | | | | | | | During hot plug, board_added will call pciehp_power_on_slot(). But link speed is updated in pciehp_power_on_slot(). We should not update link speed there, because that is too early. So move the link speed update to pciehp_check_link_status() after making sure the link has been trained. -v2: fix compile warning that Kenji found. Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com> Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: change wait time for valid configuration accessKenji Kaneshige2011-07-221-9/+2
| | | | | | | | | | | | | | | Naoki Yanagimoto reported that configuration read on some hot-added PCIe device returns invalid value. This patch fixes this problem. According to the PCIe spec, software must wait for at least 1 second to judge if the hot-added device is broken after Data Link Layer State Changed Event. This patch changes pciehp driver to wait for 1 second after the Data Link Layer State Changed Event is detected before initiating a configuration access instead of 100 ms. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Tested-by: Naoki Yanagimoto <yanagimoto@np.css.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* pciehp: update workqueue usageTejun Heo2010-10-181-19/+1
| | | | | | | | | | | | | | | * Rename pciehp_wq to pciehp_ordered_wq and add non-ordered pciehp_wq which is used instead of the system workqueue. This is to remove the use of flush_scheduled_work() which is deprecated and scheduled for removal. * With cmwq in place, there's no point in creating workqueues lazily. Create both pciehp_wq and pciehp_ordered_wq upfront. * Include workqueue.h from pciehp.h. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo2010-03-301-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* PCI: print resources consistently with %pRBjorn Helgaas2010-03-241-3/+2
| | | | | | | No functional change; just print resources in the conventional style. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: Make current and maximum bus speeds part of the PCI coreMatthew Wilcox2010-02-221-63/+9
| | | | | | | | | | Move the max_bus_speed and cur_bus_speed into the pci_bus. Expose the values through the PCI slot driver instead of the hotplug slot driver. Update all the hotplug drivers to use the pci_bus instead of their own data structures. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: Unify pcie_link_speed and pci_bus_speedMatthew Wilcox2010-02-221-8/+8
| | | | | | | | | These enums must not overlap anyway, since we only have a single pci_bus_speed_strings array. Use a single enum, and move it to pci.h. Add 'SPEED' to the pcie names to make it clear what they are. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI pciehp: fix power fault interrupt storm problemKenji Kaneshige2009-11-241-15/+11
| | | | | | | | | | | | | | | | | Enabling power fault detected event notification in current pciehp might cause power fault interrupt storm on some machines. On those machines. On those machines, power fault detected bit in the slot status register was set again immediately when it is cleared in the interrupt service routine, and next power fault detected interrupt was notified again. Therefore, disable power fault detected event notification for now. This patch also removes unnecessary handling for power fault cleared event because this event is not supported by PCIe spec. Tested-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* pciehp: use pci_pcie_cap()Kenji Kaneshige2009-11-241-23/+23
| | | | | | | | | | | Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability offset in pciehp driver. This avoids unnecessary search in PCI configuration space. This patch also removes 'cap_base' field in struct controller, that was used to hold PCIe capability offset by pciehp itself. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: return error on read/write failureKenji Kaneshige2009-11-041-16/+13
| | | | | | | | | | | | | Current pciehp returns successfully on read/write failure with dummy state values. It should return error instead. With this patch, pciehp no longer uses hotplug_slot_info data structure. So this also removes hotplug_slot_info related code. But note that it still allocates hotplug_slot_info because it is required by pci hotplug core. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove wrong workaround for bad DLLPKenji Kaneshige2009-11-041-50/+3
| | | | | | | | Remove wrong workaround for BAD DLLP error, which confused surprise down error with DLL errors. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: disable DLL state changed event notificationKenji Kaneshige2009-11-041-1/+2
| | | | | | | | | Current pciehp doesn't handle Data Link Layer State Changed Event notification. So it needs to be disabled at initialization time, otherwise other event notifications are not generated. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove number fieldKenji Kaneshige2009-09-171-1/+0
| | | | | | | | | Since slot_cap field in struct controller contains physical slot number informationq, we don't need number field in struct slot. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove hpc_opsKenji Kaneshige2009-09-171-43/+17
| | | | | | | | | | The struct hpc_ops seems a set of hooks to controller specific routines. But, it is meaningless because no hotplug controller driver follows this framework. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove pci_dev fieldKenji Kaneshige2009-09-171-8/+7
| | | | | | | | | Since we have a pointer to pcie_device in struct controller, we don't need a pointer to pci_dev. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove crit_sect mutexKenji Kaneshige2009-09-171-1/+0
| | | | | | | | | | | The crit_sect mutex defined in struct controller is to serialize hot-plug operations against multiple slots under the same bus. But, since PCIe doesnstream port has only one slot at most, it is meaningless and we don't need it. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove first_slot fieldKenji Kaneshige2009-09-171-3/+2
| | | | | | | | | | The slot number can be calculated only by physical slot number field in the slot capabilities register. So the first_slot field in struct controller is meaningless and we don't need it. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove slot_device_offset fieldKenji Kaneshige2009-09-171-1/+0
| | | | | | | | | | Since the device number of the hot-slot under the PCIe downstream port is always 0, the slot_device_offset field in the slot is meaningless and we don't need it. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove hp_slot fieldKenji Kaneshige2009-09-171-5/+0
| | | | | | | | | | The hp_slot field is to identify the slot under the same controller. But, since PCIe downstream port has only one slot at most, it is meaningless and we don't need it. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove device fieldKenji Kaneshige2009-09-171-1/+0
| | | | | | | | | The device field in the struct slot is not necessary because it is always 0 in pciehp driver. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove bus fieldKenji Kaneshige2009-09-171-1/+0
| | | | | | | | The bus field in struct slot is not necessary. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove num_slots fieldKenji Kaneshige2009-09-171-1/+0
| | | | | | | | | | Since PCIe downstream port has only one slot at most, we don't need num_slots field in struct controller. Note that struct controller itself doesn't exist if PCIe downstream port has no slot. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove slot_list fieldKenji Kaneshige2009-09-171-13/+7
| | | | | | | | | Since PCIe downstream port has only one slot at most, we don't need 'slot_list' linked list to manage multiple slots under the port. Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI hotplug: add support for 5.0G link speedKenji Kaneshige2009-09-091-2/+8
| | | | | | | | Add support for PCI-E 5.0 GT/s in max_bus_speed and cur_bus_speed. Reviewed-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: Remove untested Electromechanical Interlock (EMI) support in pciehp.Kenji Kaneshige2009-06-161-31/+0
| | | | | | | | | | | | | | | | | The EMI support in pciehp is obviously broken. It is implemented using struct hotplug_slot_attribute, but sysfs_ops for pci_slot_ktype is NOT for struct hotplug_slot_attribute, but for struct pci_slot_attribute. This bug had been there for a long time, maybe it was introduced when PCI slot framework was introduced. The reason why this bug didn't cause any problem is maybe the EMI support is not tested at all because of lack of test environment. As described above, the EMI support in pciehp seems not to be tested at all. So this patch removes EMI support from pciehp, instead of fixing the bug. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: enable software notification on empty slotsKenji Kaneshige2009-03-191-20/+11
| | | | | | | | | | | | | | | | | | | | | | | | Current pciehp disables software notification of adapter presence changed event and MRL changed event when slot is turned off. Because of this, there is no way to detect those events on empty slots in the current pciehp implementation. According to the past discussion(*), this behavior was introduced to prevent endless loop that could happen if pcie_isr() runs after power fault is detected on a certain platform whose stickey power-fault bit remains on till the slot is powered on again. (*) http://sourceforge.net/mailarchive/message.php?msg_id=20051130135409.A14918%40unix-os.sc.intel.com I think this endless loop can be avoided using one bit flag that indicates power fault had been detected, instead of disabling software notification of adapter present changed event and MRL changed event. With this patch, we can enable software notification mechanism of presence changed and MRL changed event on the empty slots again. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: fix possible endless loop in pcie_isrKenji Kaneshige2009-03-191-1/+2
| | | | | | | | | | | | | | Fix possible endless loop in pcie_isr. Currently, pcie_isr() (interrupt service routine of pciehp) can end up in an endless loop if the Slot Status register is set again immediately after being cleared. According to the past discussion (see below URL) this case can happen if the power fault detected bit is set during handling. http://sourceforge.net/mailarchive/message.php?msg_id=20051130135409.A14918%40unix-os.sc.intel.com Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: Handle interrupts that happen during initialization.Eric W. Biederman2009-02-241-8/+7
| | | | | | | | | | | Move the enabling of interrupts after all of the data structures are setup so that we can safely run the interrupt handler as soon as it is registered. Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
* PCI: pciehp: cleanup register and field definitionsKenji Kaneshige2009-01-071-229/+99
| | | | | | | | | | | | | Clean up register definitions related to PCI Express Hot plug. - Add register definitions into include/linux/pci_regs.h, and use them instead of pciehp's locally definied register definitions. - Remove pciehp's locally defined register definitions - Remove unused register definitions in pciehp. - Some minor cleanups. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: ignore undefined bit in link status registerKenji Kaneshige2009-01-071-2/+1
| | | | | | | | | | Bit 10 in Link Status register used to be defined as Training Error in the PCI Express 1.0a specification. But it was removed by Training Error ECN and is no longer defined. So pciehp must ignore the value read from it. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI hotplug: pciehp: message refinementTaku Izumi2008-10-231-26/+17
| | | | | | | | | | | | | This patch refines messages in pciehp module. The main changes are as follows: - remove the trailing "." - remove __func__ as much as possible - capitalize the first letter of messages - show PCI device address including its domain Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI hotplug: pciehp: poll data link layer link activeKenji Kaneshige2008-10-221-1/+54
| | | | | | | | | This patch adds polling mechanism for Data Link Layer Link Active bit after turning power on, instead of waiting for 1000 msec. This reduces reduce the unnecessary long wait. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI hotplug: pciehp: fix possible memory leak in pcie_initKenji Kaneshige2008-10-221-2/+2
| | | | | | | Fix the error paths in pcie_init to avoid leaking memory. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: remove 'name' parameterAlex Chiang2008-10-221-1/+0
| | | | | | | | | | | | | | We do not need to manage our own name parameter, especially since the PCI core can change it on our behalf, in the case of duplicate slot names. Remove 'name' from pciehp's version of struct slot, and remove unused 'task_list' as well. Cc: kristen.c.accardi@intel.com Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: replace printk with dev_printkTaku Izumi2008-10-201-84/+113
| | | | | | | This patch replaces printks within pciehp module with dev_printks. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: fix irq initializationKenji Kaneshige2008-10-201-2/+3
| | | | | | | | | Current pciehp driver gets irq number from pci_dev->irq. But because pciehp driver is a pci express port service driver, it should get irq number from pcie_device->irq. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: fix pciehp_free_irq()Adrian Bunk2008-09-101-1/+1
| | | | | | | | | | | This patch fixes an obvious bug (loop was never entered) caused by commit 820943b6fc4781621dee52ba026106758a727dd3 (pciehp: cleanup pcie_poll_cmd). Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: Rename duplicate slot name N as N-1, N-2, N-M...Alex Chiang2008-08-211-10/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 3800345f723fd130d50434d4717b99d4a9f383c8 (pciehp: fix slot name) introduces the pciehp_slot_with_bus module parameter, which was intended to help work around broken firmware that assigns the same name to multiple slots. Commit 9e4f2e8d4ddb04ad16a3828cd9a369a5a5287009 (pciehp: add message about pciehp_slot_with_bus option) tells the user to use the above parameter in the event of a name collision. This approach is sub-optimal because it requires too much work from the user. Instead, let's rename the slot on behalf of the user. If firmware assigns the name N to multiple slots, then: The first registered slot is assigned N The second registered slot is assigned N-1 The third registered slot is assigned N-2 The Mth registered slot becomes N-M In the event we overflow the slot->name parameter, we report an error to the user. This is a temporary fix until the entire PCI core can be reworked such that individual drivers no longer have to manage their own slot names. Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI hotplug: fix typo in pcie hotplug outputJesse Barnes2008-07-281-1/+1
| | | | | | Comamnd->Command Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* pciehp: remove needless command completed interrupt settingKenji Kaneshige2008-06-271-7/+3
| | | | | | | | | | | | | | | | | | | Currently, pciehp driver enables command completed interrupt as follows. (1) Don't enable at initialization. (2) Enable command completed interrupt whenever pciehp issues a command, if the command doesn't attempt to disable the interrupt. (3) Disable command completed interrupt at driver unloading. Once we enable command completed interrupt, we don't need to re-enable it for every command. So we can simplify above steps as follows: (1) Enable command completed interrupt at initialization. (2) No special sequence for command completed interrupt. (3) Disable command completed interrupt at driver unloading. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* pciehp: fix interrupt initializationKenji Kaneshige2008-06-271-66/+113
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current pciehp driver's intialization sequence is as follows: (1) initialize controller data structure (2) install interrupt handler (3) enable software notification (4) initialize controller specific slot data structure (5) initialize generic slot data structure and register it to pci hotplug core The interrupt handler of pciehp assumes that controller specific slot data structure is already initialized. However, it is installed at (2) before initializing controller specific slot data structure at (4). Because of this, pciehp driver cannot handle the following cases properly. - If devices that shares IRQ with pciehp raise interrupts between (2) and (4). - If hotplug events (e.g. MRL open) happen between (3) and (4). We already have a workaround for this problem ("pciehp: fix NULL dereference in interrupt handler: dbd79aed1aea2bece0bf43cc2ff3b2f9baf48a08). But we still need fundamental fix. This patch fix the problem by changing the initilization sequence as follows: (1) initialize controller data structure (2) initialize controller specific slot data structure (3) install interrupt handler (4) enable software notification (5) initialize generic slot data structure and register it to pci hotplug core Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-24 08:29:00 +0000