summaryrefslogtreecommitdiffstats
path: root/drivers/pinctrl/intel
Commit message (Collapse)AuthorAgeFilesLines
* pinctrl: baytrail: Fix pin being driven low for a while on gpiod_get(..., ↵Hans de Goede2020-06-261-14/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | GPIOD_OUT_HIGH) The pins on the Bay Trail SoC have separate input-buffer and output-buffer enable bits and a read of the level bit of the value register will always return the value from the input-buffer. The BIOS of a device may configure a pin in output-only mode, only enabling the output buffer, and write 1 to the level bit to drive the pin high. This 1 written to the level bit will be stored inside the data-latch of the output buffer. But a subsequent read of the value register will return 0 for the level bit because the input-buffer is disabled. This causes a read-modify-write as done by byt_gpio_set_direction() to write 0 to the level bit, driving the pin low! Before this commit byt_gpio_direction_output() relied on pinctrl_gpio_direction_output() to set the direction, followed by a call to byt_gpio_set() to apply the selected value. This causes the pin to go low between the pinctrl_gpio_direction_output() and byt_gpio_set() calls. Change byt_gpio_direction_output() to directly make the register modifications itself instead. Replacing the 2 subsequent writes to the value register with a single write. Note that the pinctrl code does not keep track internally of the direction, so not going through pinctrl_gpio_direction_output() is not an issue. This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is already on at boot (no external monitor connected), then the i915 driver does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The temporarily going low of that GPIO was causing the panel to reset itself after which it would not show an image until it was turned off and back on again (until a full modeset was done on it). This commit fixes this. This commit also updates the byt_gpio_direction_input() to use direct register accesses instead of going through pinctrl_gpio_direction_input(), to keep it consistent with byt_gpio_direction_output(). Note for backporting, this commit depends on: commit e2b74419e5cc ("pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output") Cc: stable@vger.kernel.org Fixes: 86e3ef812fe3 ("pinctrl: baytrail: Update gpio chip operations") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: intel: Move npins closer to pin_base in struct intel_communityAndy Shevchenko2020-04-221-2/+3
| | | | | | | | | | | | It's common across the drivers to use the (pin_base, npins) pair to describe community characteristics. Thus, move them in the struct intel_community to be closer to each other. While at it, add a blank line to cut driver usable fields from what core reserves for itself. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: intel: Update description in struct intel_communityAndy Shevchenko2020-04-221-3/+3
| | | | | | | | | | | It appears that most of the drivers, that are using struct intel_community, utilize gpps rather than gpp_size. Update comment accordingly. While here, correct the description of gpp_size, i.e. remove double space and drop redundant 'etc.' part. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: cherryview: Add missing spinlock usage in chv_gpio_irq_handlerGrace Kao2020-04-171-0/+4
| | | | | | | | | | | | | | | | According to Braswell NDA Specification Update (#557593), concurrent read accesses may result in returning 0xffffffff and write instructions may be dropped. We have an established format for the commit references, i.e. cdca06e4e859 ("pinctrl: baytrail: Add missing spinlock usage in byt_gpio_irq_handler") Fixes: 0bd50d719b00 ("pinctrl: cherryview: prevent concurrent access to GPIO controllers") Signed-off-by: Grace Kao <grace.kao@intel.com> Reported-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: lynxpoint: Use platform_get_irq_optional() explicitlyAndy Shevchenko2020-04-161-5/+5
| | | | | | | | | There is no need to repeat functionality of platform_get_irq_optional() in the driver. Replace it with explicit call to the helper. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: baytrail: Use platform_get_irq_optional() explicitlyAndy Shevchenko2020-04-151-5/+4
| | | | | | | | There is no need to repeat functionality of platform_get_irq_optional() in the driver. Replace it with explicit call to the helper. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: intel: Add Intel Jasper Lake pin controller supportAndy Shevchenko2020-04-143-0/+353
| | | | | | | | | | This driver adds pinctrl/GPIO support for Intel Jasper Lake SoC. The GPIO controller is based on the next generation GPIO hardware but still compatible with the one supported by the Intel core pinctrl/GPIO driver. Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: intel: Introduce new flag to force GPIO base to be 0Andy Shevchenko2020-04-142-0/+5
| | | | | | | | | | | In some cases not the first group would like to have GPIO base to be 0. It's not possible right now due to 0 has special meaning already. Thus, introduce a new flag to allow drivers to force GPIO base to be 0 on a certain group. It's assumed that it can be only one group per device with such flag enabled. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: tigerlake: Use generic flag for special GPIO base treatmentAndy Shevchenko2020-04-141-17/+15
| | | | | | | | Since we have a generic flag for special GPIO base treatment, use it in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: icelake: Use generic flag for special GPIO base treatmentAndy Shevchenko2020-04-141-16/+14
| | | | | | | | Since we have a generic flag for special GPIO base treatment, use it in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: cannonlake: Use generic flag for special GPIO base treatmentAndy Shevchenko2020-04-141-30/+28
| | | | | | | | Since we have a generic flag for special GPIO base treatment, use it in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: intel: Introduce common flags for GPIO mapping schemeAndy Shevchenko2020-04-142-8/+25
| | | | | | | | | | Few drivers are using the same flag to tell Intel pin control core how to interpret GPIO base. Provide a generic flags so all drivers can use. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: cherryview: Use GENMASK() consistentlyAndy Shevchenko2020-04-131-8/+8
| | | | | | | | Use GENMASK() macro for all definitions where it's appropriate. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: cherryview: Re-use data structures from pinctrl-intel.h (part 2)Andy Shevchenko2020-04-131-165/+97
| | | | | | | | | We have some data structures duplicated across the drivers. Let's deduplicate them by using ones that being provided by pinctrl-intel.h. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: baytrail: Enable pin configuration setting for GPIO chipAndy Shevchenko2020-04-131-0/+1
| | | | | | | | | | | | It appears that pin configuration for GPIO chip hasn't been enabled yet due to absence of ->set_config() callback. Enable it here for Intel Baytrail. Fixes: c501d0b149de ("pinctrl: baytrail: Add pin control operations") Depends-on: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: sunrisepoint: Fix PAD lock register offset for SPT-HAndy Shevchenko2020-04-131-7/+8
| | | | | | | | | It appears that SPT-H variant has different offset for PAD locking registers. Fix it here. Fixes: 551fa5801ef1 ("pinctrl: intel: sunrisepoint: Add Intel Sunrisepoint-H support") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: tigerlake: Tiger Lake uses _HID enumerationMika Westerberg2020-01-161-297/+250
| | | | | | | | | | Turns out that Tiger Lake GPIO will be enumerated using _HID method where there is only a single ACPI device and multiple BARs so rework the driver to support that scheme instead. Fixes: c9ccf71fc807 ("pinctrl: intel: Add Intel Tiger Lake pin controller support") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: sunrisepoint: Add Coffee Lake-S ACPI IDMika Westerberg2020-01-161-0/+1
| | | | | | | | | Intel Coffee Lake-S PCH has the same GPIO hardware than Sunrisepoint-H PCH but the ACPI ID is different. Add this new ACPI ID to the list of supported devices. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: intel: Pass irqchip when adding gpiochipLinus Walleij2020-01-091-13/+13
| | | | | | | | | | | | | We need to convert all old gpio irqchips to pass the irqchip setup along when adding the gpio_chip. For more info see drivers/gpio/TODO. For chained irqchips this is a pretty straight-forward conversion. Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: intel: Add GPIO <-> pin mapping ranges via callbackLinus Walleij2020-01-091-13/+22
| | | | | | | | | | | | | When IRQ chip is instantiated via GPIO library flow, the few functions, in particular the ACPI event registration mechanism, on some of ACPI based platforms expect that the pin ranges are initialized to that point. Add GPIO <-> pin mapping ranges via callback in the GPIO library flow. Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq ↵Hans de Goede2020-01-091-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | pin to output Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI resource so we can do this without problems as long as we release the IRQ before changing the pin to output mode. On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, but this triggers the WARN in byt_gpio_set_direction-s output path because direct-irq support is enabled on the pin. This commit replaces the WARN call with a dev_info_once call, fixing a bunch of WARN splats in dmesg on each suspend/resume cycle. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pinsHans de Goede2020-01-091-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, until the goodix driver gets rmmod-ed and then insmod-ed again. In this case byt_gpio_disable_free() calls byt_gpio_clear_triggering() which clears the IRQ flags and after that the (direct) IRQ no longer triggers. This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag to byt_gpio_clear_triggering(). Note that byt_gpio_clear_triggering() only gets called from byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded from the irq_valid mask by byt_init_irq_valid_mask(). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: sunrisepoint: Add missing Interrupt Status register offsetBoyan Ding2020-01-081-0/+1
| | | | | | | | | | | | | | | Commit 179e5a6114cc ("pinctrl: intel: Remove default Interrupt Status offset") removes default interrupt status offset of GPIO controllers, with previous commits explicitly providing the previously default offsets. However, the is_offset value in SPTH_COMMUNITY is missing, preventing related irq from being properly detected and handled. Fixes: f702e0b93cdb ("pinctrl: sunrisepoint: Provide Interrupt Status register offset") Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745 Cc: stable@vger.kernel.org Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: lynxpoint: Update summary in the driverAndy Shevchenko2019-12-131-4/+6
| | | | | | | | | | Reflect in the driver that it is now a pin control one. While here, update copyright years and authors. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Switch to pin control APIAndy Shevchenko2019-12-132-57/+13
| | | | | | | | When all preparations are done, we may switch to pin control API. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Add GPIO <-> pin mapping ranges via callbackAndy Shevchenko2019-12-131-0/+14
| | | | | | | | | | | | When IRQ chip is instantiated via GPIO library flow, the few functions, in particular the ACPI event registration mechanism, on some of ACPI based platforms expect that the pin ranges are initialized to that point. Add GPIO <-> pin mapping ranges via callback in the GPIO library flow. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Implement ->pin_dbg_show()Andy Shevchenko2019-12-131-0/+23
| | | | | | | | The introduced callback ->pin_dbg_show() is useful for debugging. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Add pin control operationsAndy Shevchenko2019-12-131-1/+314
| | | | | | | | | | | | | | | | Add implementation for: - pin control, group information retrieval: count, name and pins - pin muxing: - function information (count, name and groups) - mux setting - GPIO control (enable, disable, set direction) - pin configuration: - pull disable, up and down - any other option is treated as not supported. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Reuse struct intel_pinctrl in the driverAndy Shevchenko2019-12-131-24/+60
| | | | | | | | | We may use now available struct intel_pinctrl in the driver. No functional change implied. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Add pin control data structuresAndy Shevchenko2019-12-131-2/+124
| | | | | | | | | | In order to implement pin control for Intel Lynxpoint, we need data structures in which to store and pass along pin, community and SoC data information. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Implement intel_gpio_get_direction callbackAndy Shevchenko2019-12-131-0/+11
| | | | | | | | | Allows querying GPIO direction from the pad config register. If the pad is not in GPIO mode, return an error. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Implement ->irq_ack() callbackAndy Shevchenko2019-12-131-3/+14
| | | | | | | | | Instead of playing tricks with registers in the interrupt handler, utilize the IRQ chip core for ACKing interrupts properly. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Move ownership check to IRQ chipAndy Shevchenko2019-12-131-6/+6
| | | | | | | | | | | | | There is nothing wrong with requesting pin that owned by ACPI. The only difference is how interrupt status will be reflected. It means that in ACPI mode we may not use pin as GPIO-backed IRQ. Taking above into consideration, move the check from GPIO to IRQ chip callback. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Move lp_irq_type() closer to IRQ related routinesAndy Shevchenko2019-12-131-44/+44
| | | | | | | | | | | Consolidate IRQ routines for better maintenance. While here, rename lp_irq_type() to lp_irq_set_type() to be in align with a callback name. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Move ->remove closer to ->probe()Andy Shevchenko2019-12-131-6/+6
| | | | | | | | Consolidate ->remove and ->probe() callbacks for better maintenance. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Extract lp_gpio_acpi_use() for future useAndy Shevchenko2019-12-131-2/+12
| | | | | | | | We may need this function for other features in the pin control driver. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Convert unsigned to unsigned intAndy Shevchenko2019-12-131-12/+12
| | | | | | | | Simple type conversion with no functional change implied. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Switch to memory mapped IO accessorsAndy Shevchenko2019-12-131-44/+44
| | | | | | | | Convert driver to use memory mapped IO accessors. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Keep pointer to struct device instead of its containerAndy Shevchenko2019-12-131-7/+7
| | | | | | | | | | | There is no need to keep pointer to struct platform_device, which is container of struct device, because the latter is what have been used everywhere outside of ->probe() path. In any case we may derive pointer to the container when needed. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Relax GPIO request rulesAndy Shevchenko2019-12-131-3/+11
| | | | | | | | | | | | A pin in native mode still can be requested as GPIO, though we assume that firmware has configured it properly, which sometimes is not the case. Here we allow turning the pin as GPIO to avoid potential issues, but issue warning that something might be wrong. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Assume 2 bits for mode selectorAndy Shevchenko2019-12-131-2/+4
| | | | | | | | | New generations can use 2 bits for mode selector. Update the code to support it. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Use standard pattern for memory allocationAndy Shevchenko2019-12-131-1/+1
| | | | | | | | | | | The pattern foo = kmalloc(sizeof(*foo), GFP_KERNEL); has an advantage when foo type is changed. Since we are planning a such, better to be prepared by using standard pattern for memory allocation. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Use %pR to print IO resourceAndy Shevchenko2019-12-131-2/+1
| | | | | | | | | Replace explicit casting by pointer to struct resource with specifier replacement to %pR to print the IO resource. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Drop useless assignmentAndy Shevchenko2019-12-131-1/+1
| | | | | | | | | There is no need to assign ret variable in ->probe(). Drop useless assignment. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Correct amount of pinsAndy Shevchenko2019-12-131-6/+6
| | | | | | | | | | When we count from 0 it's possible to get into off-by-one error. That's what had happened to this driver. So, correct amount of pins and related typos in the code. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Use raw_spinlock for lockingAndy Shevchenko2019-12-131-14/+14
| | | | | | | | | | | | | | | | | The Intel Lynxpoint pinctrl driver implements irqchip callbacks which are called with desc->lock raw_spinlock held. In mainline this is fine because spinlock resolves to raw_spinlock. However, running the same code in -rt we will get a BUG() asserted. This is because in -rt spinlocks are preemptible so taking the driver private spinlock in irqchip callbacks causes might_sleep() to trigger. In order to keep -rt happy but at the same time make sure that register accesses get serialized, convert the driver to use raw_spinlock instead. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: lynxpoint: Move GPIO driver to pin controller folderAndy Shevchenko2019-12-133-0/+482
| | | | | | | | | Move Lynxpoint GPIO driver under Intel pin control umbrella for further transformation to a real pin control driver. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pinctrl: baytrail: Reuse struct intel_pinctrl in the driverAndy Shevchenko2019-12-131-99/+87
| | | | | | | | | | We may use now available struct intel_pinctrl in the driver. No functional change implied. Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: baytrail: Use local variable to keep device pointerAndy Shevchenko2019-12-131-9/+10
| | | | | | | | | | Use local variable to keep device pointer in order to increase readability of the driver. Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* pinctrl: baytrail: Keep pointer to struct device instead of its containerAndy Shevchenko2019-12-131-29/+29
| | | | | | | | | | | | There is no need to keep pointer to struct platform_device, which is container of struct device, because the latter is what have been used everywhere outside of ->probe() path. In any case we may derive pointer to the container when needed. Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-03-20 21:24:15 +0000