summaryrefslogtreecommitdiffstats
path: root/drivers/pinctrl/sunxi
Commit message (Collapse)AuthorAgeFilesLines
...
* pinctrl: sunxi: Support I/O bias voltage setting on A80Chen-Yu Tsai2019-02-114-0/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | The A80 SoC has configuration registers for I/O bias voltage. Incorrect settings would make the affected peripherals inoperable in some cases, such as Ethernet RGMII signals biased at 2.5V with the settings still at 3.3V. However low speed signals such as MDIO on the same group of pins seem to be unaffected. Previously there was no way to know what the actual voltage used was, short of hard-coding a value in the device tree. With the new pin bank regulator supply support in place, the driver can now query the regulator for its voltage, and if it's valid (as opposed to being the dummy regulator), set the bias voltage setting accordingly. Add a quirk to denote the presence of the configuration registers, and a function to set the correct setting based on the voltage read back from the regulator. This is only done when the regulator is first acquired and enabled. While it would be nice to have a notifier on the regulator so that when the voltage changes, the driver can update the setting, in practice no board currently supports dynamic changing of the I/O voltages. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: Correct number of IRQ banks on H6 main pin controllerChen-Yu Tsai2019-01-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The H6 main pin controller has four banks of interrupt-triggering pins. The driver as originally submitted only specified three, but had pin descriptions referencing a fourth bank. This results in a out-of-bounds access into .irq_array of struct sunxi_pinctrl. This however did not result in a crash until v4.20, with commit a66d972465d1 ("devres: Align data[] to ARCH_KMALLOC_MINALIGN"), which changed the alignment of memory region returned by devm_kcalloc(). The increase likely moved the out-of-bounds access into the next, unmapped page. With KASAN on, the bug is quite clear: BUG: KASAN: slab-out-of-bounds in sunxi_pinctrl_init_with_variant+0x49c/0x12b8 Write of size 4 at addr ffff80002c680280 by task swapper/0/1 CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1-00016-gc480a5e6a077 #3 Hardware name: OrangePi Lite2 (DT) Call trace: dump_backtrace+0x0/0x220 show_stack+0x14/0x20 dump_stack+0xac/0xd4 print_address_description+0x60/0x25c kasan_report+0x14c/0x1ac __asan_store4+0x80/0xa0 sunxi_pinctrl_init_with_variant+0x49c/0x12b8 h6_pinctrl_probe+0x18/0x20 platform_drv_probe+0x6c/0xc8 really_probe+0x244/0x4b0 driver_probe_device.part.4+0x11c/0x164 __driver_attach+0x120/0x190 bus_for_each_dev+0xe8/0x158 driver_attach+0x30/0x40 bus_add_driver+0x308/0x318 driver_register+0xbc/0x1d0 __platform_driver_register+0x7c/0x88 h6_pinctrl_driver_init+0x18/0x20 do_one_initcall+0xd4/0x208 kernel_init_freeable+0x230/0x2c8 kernel_init+0x10/0x108 ret_from_fork+0x10/0x1c Allocated by task 1: kasan_kmalloc.part.0+0x4c/0x100 kasan_kmalloc+0xc4/0xe8 kasan_slab_alloc+0x14/0x20 __kmalloc_track_caller+0x130/0x238 devm_kmalloc+0x34/0xd0 sunxi_pinctrl_init_with_variant+0x1d8/0x12b8 h6_pinctrl_probe+0x18/0x20 platform_drv_probe+0x6c/0xc8 really_probe+0x244/0x4b0 driver_probe_device.part.4+0x11c/0x164 __driver_attach+0x120/0x190 bus_for_each_dev+0xe8/0x158 driver_attach+0x30/0x40 bus_add_driver+0x308/0x318 driver_register+0xbc/0x1d0 __platform_driver_register+0x7c/0x88 h6_pinctrl_driver_init+0x18/0x20 do_one_initcall+0xd4/0x208 kernel_init_freeable+0x230/0x2c8 kernel_init+0x10/0x108 ret_from_fork+0x10/0x1c Freed by task 0: (stack is not available) The buggy address belongs to the object at ffff80002c680080 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 0 bytes to the right of 512-byte region [ffff80002c680080, ffff80002c680280) The buggy address belongs to the page: page:ffff7e0000b1a000 count:1 mapcount:0 mapping:ffff80002e00c780 index:0xffff80002c683c80 compound_mapcount: 0 flags: 0x10200(slab|head) raw: 0000000000010200 ffff80002e003a10 ffff80002e003a10 ffff80002e00c780 raw: ffff80002c683c80 0000000000100001 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff80002c680180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff80002c680200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff80002c680280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff80002c680300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff80002c680380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc Correct the number of IRQ banks so there are no more mismatches. Fixes: c8a830904991 ("pinctrl: sunxi: add support for the Allwinner H6 main pin controller") Cc: <stable@vger.kernel.org> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: Consider pin_base when calculating regulator array indexChen-Yu Tsai2019-01-142-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | On most newer Allwinner SoCs, there are two pinctrl devices, the PIO and R_PIO. PIO covers pin-banks PA to PI (PJ and PK have not been seen), while R_PIO covers PL to PN. The regulator array only has space for 12 entries, which was designed to cover PA to PL. On the A80, the pin banks go up to PN, which would be the 14th entry in the regulator array. However since the driver only needs to track regulators for its own pin banks, the array only needs to have 9 entries, and also take in to account the value of pin_base, such that the regulator for the first pin-bank of the pinctrl device, be it "PA" or "PL" uses the first entry of the array. Base the regulator array index on pin_base, such that "PA" for PIO and "PL" for R_PIO both take the first element within their respective device's regulator array. Also decrease the size of the regulator array to 9, just enough to cover "PA" to "PI". Fixes: 9a2a566adb00 ("pinctrl: sunxi: Deal with per-bank regulators") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: Fix and simplify pin bank regulator handlingChen-Yu Tsai2019-01-141-20/+16
| | | | | | | | | | | | | | | | | The new per-pin-bank regulator handling code in the sunxi pinctrl driver has mismatched conditions for enabling and disabling the regulator: it is enabled each time a pin is requested, but only disabled when the pin-bank's reference count reaches zero. Since we are doing reference counting already, there's no need to enable the regulator each time a pin is requested. Instead we can just do it for the first requested pin of each pin-bank. Thus we can reverse the test and bail out early if it's not the first occurrence. Fixes: 9a2a566adb00 ("pinctrl: sunxi: Deal with per-bank regulators") Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Merge tag 'pinctrl-v4.21-1' of ↵Linus Torvalds2019-01-016-26/+516
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "We have no core changes but lots of incremental development in drivers all over the place: Renesas, NXP, Mediatek and Actions Semiconductor keep churning out new SoCs. I have some subtree maintainers for Renesas and Intel helping out to keep down the load, it's been working smoothly (Samsung also have a subtree but it was not used this cycle.) New drivers: - NXP (ex Freescale) i.MX 8 QXP SoC driver. - Mediatek MT6797 SoC driver. - Mediatek MT7629 SoC driver. - Actions Semiconductor S700 SoC driver. - Renesas RZ/A2 SoC driver. - Allwinner sunxi suniv F1C100 SoC driver. - Qualcomm PMS405 PMIC driver. - Microsemi Ocelot Jaguar2 SoC driver. Improvements: - Some RT improvements (using raw spinlocks where appropriate). - A lot of new pin sets on the Renesas PFC pin controllers. - GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO chips, and Xway. - Major modernization of the Intel pin control drivers. - STM32 pin control driver will now synchronize usage of pins with another CPU using a hardware spinlock" * tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits) dt-bindings: arm: fsl-scu: add imx8qm pinctrl support pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ pinctrl: imx-scu: Depend on IMX_SCU pinctrl: ocelot: Add dependency on HAS_IOMEM pinctrl: ocelot: add MSCC Jaguar2 support pinctrl: bcm: ns: support updated DT binding as syscon subnode dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon MAINTAINERS: merge at91 pinctrl entries pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP pinctrl: uniphier: constify uniphier_pinctrl_socdata pinctrl: mediatek: improve Kconfig dependencies pinctrl: msm: mark PM functions as __maybe_unused dt-bindings: pinctrl: sunxi: Add supply properties pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs" pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs" pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length ...
| * pinctrl: sunxi: Deal with per-bank regulatorsMaxime Ripard2018-12-142-0/+69
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Allwinner SoCs have on most of their GPIO banks a regulator input. This issue was mainly ignored so far because either the regulator was a static regulator that would be providing power anyway, or the bank was used for a feature unsupported so far (CSI). For the odd cases, enabling it in the bootloader was the preferred option. However, now that we are starting to support those features, and that we can't really rely on the bootloader for this, we need to model those regulators as such in the DT. This is slightly more complicated than what it looks like, since some regulators will be tied to the PMIC, and in order to have access to the PMIC bus, you need to mux its pins, which will need the pinctrl driver, that needs the regulator driver to be registered. And this is how you get a circular dependency. In practice however, the hardware cannot fall into this case since it would result in a completely unusable bus. In order to avoid that circular dependency, we can thus get and enable the regulators at pin_request time. We'll then need to account for the references of all the pins of a particular branch to know when to put the reference, but it works pretty nicely once implemented. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * pinctrl: sunxi: a64: Rename function ts0 to tsChen-Yu Tsai2018-12-071-12/+12
| | | | | | | | | | | | | | | | | | | | | | | | The A64 only has one TS (transport stream) controller. The datasheet also lists the function as TS_XXX instead of TS0_XXX. Rename the function names now before any there are any users. Fixes: 96851d391d02 ("drivers: pinctrl: add driver for Allwinner A64 SoC") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * pinctrl: sunxi: a64: Rename function csi0 to csiChen-Yu Tsai2018-12-071-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | The A64 only has one CSI (camera sensor interface) controller. The datasheet also lists the function as CSI_XXX instead of CSI0_XXX. Rename the function names now before any there are any users. Fixes: 96851d391d02 ("drivers: pinctrl: add driver for Allwinner A64 SoC") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * pinctrl: sunxi: add support for suniv F1C100s (newer F-series SoCs)Mesih Kilinc2018-11-253-0/+421
| | | | | | | | | | | | | | | | | | | | | | | | The suniv F1C100s chip (several new F-series SoCs) of Allwinner has a pin controller like other SoCs from Allwinner. Add support for it. Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | pinctrl: sunxi: a83t: Fix IRQ offset typo for PH11Chen-Yu Tsai2018-12-071-1/+1
|/ | | | | | | | | | | | | | Pin PH11 is used on various A83T board to detect a change in the OTG port's ID pin, as in when an OTG host cable is plugged in. The incorrect offset meant the gpiochip/irqchip was activating the wrong pin for interrupts. Fixes: 4730f33f0d82 ("pinctrl: sunxi: add allwinner A83T PIO controller support") Cc: <stable@vger.kernel.org> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: Fix a memory leak in 'sunxi_pinctrl_build_state()'Christophe JAILLET2018-10-161-4/+7
| | | | | | | | | | If 'krealloc()' fails, 'pctl->functions' is set to NULL. We should instead use a temp variable in order to be able to free the previously allocated memeory, in case of OOM. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: fix 'pctrl->functions' allocation in sunxi_pinctrl_build_stateYueHaibing2018-09-211-6/+9
| | | | | | | | | | | | | | | | | fixes following Smatch static check warning: ./drivers/pinctrl/sunxi/pinctrl-sunxi.c:1112 sunxi_pinctrl_build_state() warn: passing devm_ allocated variable to kfree. 'pctrl->functions' As we will be calling krealloc() on pointer 'pctrl->functions', which means kfree() will be called in there, devm_kzalloc() shouldn't be used with the allocation in the first place. Fix the warning by calling kcalloc() and managing the free procedure in error path on our own. Fixes: 0e37f88d9ad8 ("ARM: sunxi: Add pinctrl driver for Allwinner SoCs") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: Convert to using %pOFn instead of device_node.nameRob Herring2018-08-291-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In preparation to remove the node name pointer from struct device_node, convert printf users to use the %pOFn format specifier. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Dong Aisheng <aisheng.dong@nxp.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Stefan Agner <stefan@agner.ch> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Sean Wang <sean.wang@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@bootlin.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Haojian Zhuang <haojian.zhuang@linaro.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Barry Song <baohua@kernel.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: linux-gpio@vger.kernel.org Cc: linux-mediatek@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-amlogic@lists.infradead.org Cc: linux-rockchip@lists.infradead.org Cc: linux-omap@vger.kernel.org Acked-by: Dong Aisheng <aisheng.dong@nxp.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Sean Wang <sean.wang@mediatek.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* treewide: devm_kzalloc() -> devm_kcalloc()Kees Cook2018-06-121-8/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
* treewide: kzalloc() -> kcalloc()Kees Cook2018-06-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
* treewide: kmalloc() -> kmalloc_array()Kees Cook2018-06-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The kmalloc() function has a 2-factor argument form, kmalloc_array(). This patch replaces cases of: kmalloc(a * b, gfp) with: kmalloc_array(a * b, gfp) as well as handling cases of: kmalloc(a * b * c, gfp) with: kmalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kmalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kmalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The tools/ directory was manually excluded, since it has its own implementation of kmalloc(). The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kmalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kmalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kmalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kmalloc( - sizeof(u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kmalloc( - sizeof(char) * COUNT + COUNT , ...) | kmalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kmalloc + kmalloc_array ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kmalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kmalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kmalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kmalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kmalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kmalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kmalloc(C1 * C2 * C3, ...) | kmalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kmalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kmalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kmalloc(sizeof(THING) * C2, ...) | kmalloc(sizeof(TYPE) * C2, ...) | kmalloc(C1 * C2 * C3, ...) | kmalloc(C1 * C2, ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kmalloc + kmalloc_array ( - (E1) * E2 + E1, E2 , ...) | - kmalloc + kmalloc_array ( - (E1) * (E2) + E1, E2 , ...) | - kmalloc + kmalloc_array ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
* Merge tag 'clk-for-linus' of ↵Linus Torvalds2018-06-091-2/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk updates from Stephen Boyd: "This time we have a good set of changes to the core framework that do some general cleanups, but nothing too major. The majority of the diff goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for Actions Semi so it takes up some lines to add all the different types, and the Qualcomm diff is there because we add support for two SoCs and it's quite a bit of data. Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And then the long tail of driver updates for various fixes and stuff follows after that. Core: - debugfs cleanups removing error checking and an unused provider API - Removal of a clk init typedef that isn't used - Usage of match_string() to simplify parent string name matching - OF clk helpers moved to their own file (linux/of_clk.h) - Make clk warnings more readable across kernel versions New Drivers: - Qualcomm SDM845 GCC and Video clk controllers - Qualcomm MSM8998 GCC - Actions Semi S900 SoC support - Nuvoton npcm750 microcontroller clks - Amlogic axg AO clock controller Removed Drivers: - Deprecated Rockchip clk-gate driver Updates: - debugfs functions stopped checking return values - Support for the MSIOF module clocks on Rensas R-Car M3-N - Support for the new Rensas RZ/G1C and R-Car E3 SoCs - Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs - Berlin and Amlogic SPDX tagging - Usage of of_clk_get_parent_count() in more places - Proper implementation of the CDEV1/2 clocks on Tegra20 - Allwinner H6 PRCM clock support and R40 EMAC support - Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet - Round closest support for meson's mpll driver - Support for meson8b nand clocks and gxbb video decoder clocks - Mediatek mali clks - STM32MP1 fixes - Uniphier LD11/LD20 stream demux system clock" * tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits) clk: qcom: Export clk_fabia_pll_configure() clk: bcm: Update and add Stingray clock entries dt-bindings: clk: Update Stingray binding doc clk-si544: Properly round requested frequency to nearest match clk: ingenic: jz4770: Add 150us delay after enabling VPU clock clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle clk: ingenic: jz4770: Change OTG from custom to standard gated clock clk: ingenic: Support specifying "wait for clock stable" delay clk: ingenic: Add support for clocks whose gate bit is inverted clk: use match_string() helper clk: bcm2835: use match_string() helper clk: Return void from debug_init op clk: remove clk_debugfs_add_file() clk: tegra: no need to check return value of debugfs_create functions clk: davinci: no need to check return value of debugfs_create functions clk: bcm2835: no need to check return value of debugfs_create functions clk: no need to check return value of debugfs_create functions clk: imx6: add EPIT clock support clk: mvebu: use correct bit for 98DX3236 NAND ...
| * pinctrl: sunxi: Use of_clk_get_parent_count() instead of open codingGeert Uytterhoeven2018-05-021-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | A new open coder has crept in since 470b73a38470e8ba ("pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding"), replace it. of_clk_get_parent_count() was moved to <linux/of_clk.h>, so include that instead of <linux/clk-provider.h>. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* | pinctrl: sunxi: add support for H6 R_PIO pin controllerIcenowy Zheng2018-05-163-0/+133
|/ | | | | | | | | | | | Allwinner H6 SoC has a R_PIO pin controller like other Allwinner SoCs, which controls the PL and PM pin banks. Add support for it. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: add support for the Allwinner H6 main pin controllerIcenowy Zheng2018-03-273-0/+619
| | | | | | | | | | | | | | | | | | | | | | The Allwinner H6 SoC has two pin controllers, one main controller (called CPUX-PORT in user manual) and one controller in CPUs power domain (called CPUS-PORT in user manual). This commit introduces support for the main pin controller on H6. The pin bank A and B are not wired out and hidden from the SoC's documents, however it's shown that the "ATE" (an AC200 chip co-packaged with the H6 die) is connected to the main SoC die via these pin banks. The information about these banks is just copied from the BSP pinctrl driver, but re-formatted to fit the mainline pinctrl driver format. The GPIO functions are dropped, as they're impossible to use -- except a GPIO&IRQ only pin (PB20) which might be the IRQ of ATE. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: change irq_bank_base to irq_bank_mapIcenowy Zheng2018-03-273-4/+11
| | | | | | | | | | | | The Allwinner H6 SoC have its pin controllers with the first IRQ-capable GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5. Change the current code that uses IRQ bank base to a IRQ bank map, in order to support the case that holes exist among IRQ banks. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: introduce IRQ bank conversion functionIcenowy Zheng2018-03-271-11/+12
| | | | | | | | | | | | | The Allwinner H6 SoC have its pin controllers with the first IRQ-capable GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5. Some refactors in the sunxi pinctrl framework are needed. This commit introduces a IRQ bank conversion function, which replaces the "(bank_base + bank)" code in IRQ register access. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: refactor irq related register function to have descIcenowy Zheng2018-03-272-20/+28
| | | | | | | | | As the new H6 SoC has holes in the IRQ registers, refactor the IRQ related register function for getting the full pinctrl desc structure. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: always look for apb blockAndre Przywara2018-03-231-1/+2
| | | | | | | | | | | | | | The Allwinner pinctrl device tree binding suggests that a clock named "apb" would drive the pin controller IP. However (for legacy reasons) we rely on this clock actually being the first clock defined. Since named clocks can be in any order, let's explicitly check for a clock called "apb" if there is more than one clock referenced. Kudo to Maxime for suggesting this much more elegant approach. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Merge tag 'pinctrl-v4.16-1' of ↵Linus Torvalds2018-02-022-3/+6
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v4.16 kernel cycle. Like with GPIO it is actually a bit calm this time. Core changes: - After lengthy discussions and partly due to my ignorance, we have merged a patch making pinctrl_force_default() and pinctrl_force_sleep() reprogram the states into the hardware of any hogged pins, even if they are already in the desired state. This only apply to hogged pins since groups of pins owned by drivers need to be managed by each driver, lest they could not do things like runtime PM and put pins to sleeping state even if the system as a whole is not in sleep. New drivers: - New driver for the Microsemi Ocelot SoC. This is used in ethernet switches. - The X-Powers AXP209 GPIO driver was extended to also deal with pin control and moved over from the GPIO subsystem. This circuit is a mixed-mode integrated circuit which is part of AllWinner designs. - New subdriver for the Qualcomm MSM8998 SoC, core of a high end mobile devices (phones) chipset. - New subdriver for the ST Microelectronics STM32MP157 MPU and STM32F769 MCU from the STM32 family. - New subdriver for the MediaTek MT7622 SoC. This is used for routers, repeater, gateways and such network infrastructure. - New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC has multimedia features and target "smart devices", I guess in-car entertainment, in-flight entertainment, industrial control panels etc. General improvements: - Incremental improvements on the SH-PFC subdrivers for things like the CAN bus. - Enable the glitch filter on Baytrail GPIOs used for interrupts. - Proper handling of pins to GPIO ranges on the Semtec SX150X - An IRQ setup ordering fix on MCP23S08. - A good set of janitorial coding style fixes" * tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (102 commits) pinctrl: mcp23s08: fix irq setup order pinctrl: Forward declare struct device pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding pinctrl: stm32: add STM32F769 MCU support pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping pinctrl: sx150x: Register pinctrl before adding the gpiochip pinctrl: sx150x: Unregister the pinctrl on release pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe() pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show() pinctrl: pinmux: Use seq_putc() in pinmux_pins_show() pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show() pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call pinctrl: mediatek: mt7622: fix potential uninitialized value being returned pinctrl: uniphier: refactor drive strength get/set functions pinctrl: imx7ulp: constify struct imx_cfg_params_decode pinctrl: imx: constify struct imx_pinctrl_soc_info pinctrl: imx7d: simplify imx7d_pinctrl_probe pinctrl: imx: use struct imx_pinctrl_soc_info as a const pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly. pinctrl: qcom: Add msm8998 pinctrl driver ...
| * pinctrl: sunxi: Use of_clk_get_parent_count() instead of open codingGeert Uytterhoeven2018-01-221-1/+2
| | | | | | | | | | Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.hao_zhang2018-01-101-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pin function can not be match correctly when SUNXI_PIN describe with mutiple variant and same function. such as: on pinctrl-sun4i-a10.c SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2), SUNXI_FUNCTION(0x0, "gpio_in"), SUNXI_FUNCTION(0x1, "gpio_out"), SUNXI_FUNCTION_VARIANT(0x2, "pwm", /* PWM0 */ PINCTRL_SUN4I_A10 | PINCTRL_SUN7I_A20), SUNXI_FUNCTION_VARIANT(0x3, "pwm", /* PWM0 */ PINCTRL_SUN8I_R40)), it would always match to the first variant function (PINCTRL_SUN4I_A10, PINCTRL_SUN7I_A20) so we should add variant compare on it. Signed-off-by: hao_zhang <hao5781286@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * pinctrl: sunxi: fix a typo when merging A20 support to A10 driverIcenowy Zheng2017-12-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | When merging A20 pinctrl support to A10 pinctrl driver, the I2C function of PI3 is wrongly written as "i2c3" (it should be "i2c4"). Fix this typo. Fixes: cad4e209c102 ("pinctrl: sunxi: add support of R40 to A10 pinctrl driver") Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl> Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | pinctrl: sunxi: Disable strict mode for H5 driverAndre Przywara2017-11-301-2/+4
| | | | | | | | | | | | | | | | | | | | | | All of the H5 boards in the kernel reference the MMC0 CD pin twice in their DT, so strict mode will make the MMC driver fail to load. To keep existing DTs working, disable strict mode in the H5 driver. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reported-by: Chris Obbard <obbardc@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | pinctrl: sunxi: Fix A64 UART mux valueAndre Przywara2017-11-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | To use pin PF4 as the RX signal of UART0, we have to write 0b011 into the respective pin controller register. Fix the wrong value we had in our table so far. Fixes: 96851d391d02 ("drivers: pinctrl: add driver for Allwinner A64 SoC") Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | pinctrl: sunxi: Fix A80 interrupt pin bankAndre Przywara2017-11-301-3/+3
|/ | | | | | | | | | | | | | | On the A80 the pins on port B can trigger interrupts, and those are assigned to the second interrupt bank. Having two pins assigned to the same interrupt bank/pin combination does not look healthy (instead more like a copy&paste bug from pins PA14-PA16), so fix the interrupt bank for pins PB14-PB16, which is actually 1. I don't have any A80 board, so could not test this. Fixes: d5e9fb31baa2 ("pinctrl: sunxi: Add A80 pinctrl muxing options") Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Merge tag 'pinctrl-v4.15-1' of ↵Linus Torvalds2017-11-1613-3/+26
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v4.15 kernel cycle: Core: - The pin control Kconfig entry PINCTRL is now turned into a menuconfig option. This obviously has the implication of making the subsystem menu visible in menuconfig. This is happening because of two things: (a) Intel have started to deploy and depend on pin controllers in a way that is affecting users directly. This happens on the highly integrated laptop chipsets named after geographical places: baytrail, broxton, cannonlake, cedarfork, cherryview, denverton, geminilake, lewisburg, merrifield, sunrisepoint... It started a while back and now it is ever more evident that this is crucial infrastructure for x86 laptops and not an embedded obscurity anymore. Users need to be aware. (b) Pin control expanders on I2C and SPI that are arch-agnostic. Currently Semtech SX150X and Microchip MCP28x08 but more are expected. Users will have to be able to configure these in directly for their set-up. - Just go and select GPIOLIB now that we made sure that GPIOLIB is a very vanilla subsystem. Do not depend on it, if we need it, select it. - Exposing the pin control subsystem in menuconfig uncovered a bunch of obscure bugs that are now hopefully fixed, all more or less pertaining to Blackfin. - Unified namespace for cross-calls between pin control and GPIO. - New support for clock skew/delay generic DT bindings and generic pin config options for this. - Minor documentation improvements. Various: - The Renesas SH-PFC pin controller has evolved a lot. It seems Renesas are churning out new SoCs by the minute. - A bunch of non-critical fixes for the Rockchip driver. - Improve the use of library functions instead of open coding. - Support the MCP28018 variant in the MCP28x08 driver. - Static constifying" * tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits) pinctrl: gemini: Fix missing pad descriptions pinctrl: Add some depends on HAS_IOMEM pinctrl: samsung/s3c24xx: add CONFIG_OF dependency pinctrl: gemini: Fix GMAC groups pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support pinctrl: ti-iodelay: remove redundant unused variable dev pinctrl: max77620: Use common error handling code in max77620_pinconf_set() pinctrl: gemini: Implement clock skew/delay config pinctrl: gemini: Use generic DT parser pinctrl: Add skew-delay pin config and bindings pinctrl: armada-37xx: Add edge both type gpio irq support pinctrl: uniphier: remove eMMC hardware reset pin-mux pinctrl: rockchip: Add iomux-route switching support for rk3288 pinctrl: intel: Add Intel Cedar Fork PCH pin controller support pinctrl: intel: Make offset to interrupt status register configurable pinctrl: sunxi: Enforce the strict mode by default pinctrl: sunxi: Disable strict mode for old pinctrl drivers pinctrl: sunxi: Introduce the strict flag pinctrl: sh-pfc: Save/restore registers for PSCI system suspend pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description ...
| * pinctrl: sunxi: Enforce the strict mode by defaultMaxime Ripard2017-10-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | The strict mode should always have been enabled on our driver, and leaving it unchecked just makes it harder to find a migration path as time passes. Let's enable it by default now so that hopefully the new SoCs should be safe. Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * pinctrl: sunxi: Disable strict mode for old pinctrl driversMaxime Ripard2017-10-3111-2/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Old pinctrl drivers will need to disable strict mode for various reasons, among which: - Some DT will still have a pinctrl group for each GPIO used, which will be rejected by pin_request. While we could remove those nodes, we still have to deal with old DTs. - Some GPIOs on these boards need to have their pin configuration changed (for bias or current), and there's no clear migration path Let's disable the strict mode on those SoCs so that there's no breakage. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * pinctrl: sunxi: Introduce the strict flagMaxime Ripard2017-10-312-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Our pinctrl device should have had strict set all along. However, it wasn't the case, and most of our old device trees also have a pinctrl group in addition to the GPIOs properties, which mean that we can't really turn it on now. All our new SoCs don't have that group, so we should still enable that mode on the newer one though. In order to enable it by default, add a flag that will allow to disable that mode that should be set by pinctrl drivers that cannot be migrated. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-021-0/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Revert "pinctrl: sunxi: Don't enforce bias disable (for now)"Priit Laes2017-08-311-1/+2
| | | | | | | | | | | | This reverts commit 2154d94b40ea2a5de05245521371d0461bb0d669. The original patch was intented to avoid some issues with the sunxi gpio rework and was supposed to be reverted after all the required DT bits had been merged around v4.10. Signed-off-by: Priit Laes <plaes@plaes.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: fix wrong irq_banks number for H5 pinctrlIcenowy Zheng2017-08-221-3/+23
| | | | | | | | | | | | | | | | The pin controller of Allwinner H5 has three IRQ banks, however in old versions of drivers and device trees, only two are set, which makes PG bank IRQ not available. If it's directly set to 3, the old device trees will fail to boot. Add a workaround (and a warning) for older device trees, and allow new device trees to use correct 3 IRQ banks. Fixes: 838adb576d4a ("drivers: pinctrl: add driver for Allwinner H5 SoC") Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: fix V3s pinctrl driver IRQ bank baseIcenowy Zheng2017-08-141-0/+1
| | | | | | | | | | | | | The V3s pin controller doesn't have the bank 0 (starts at address 0x200), which is like A33. However, this is not worked around when developing the driver, which makes IRQ not working. Fix the IRQ bank base. Fixes: 56d9e4a76039 ("pinctrl: sunxi: add driver for V3s SoC") Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: explicitly request exclusive reset controlPhilipp Zabel2017-08-142-2/+2
| | | | | | | | | | | | | | | | | Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: rename R_PIO i2c pin function nameIcenowy Zheng2017-08-143-6/+6
| | | | | | | | | | | | | | The I2C pin functions in R_PIO used to be named "s_twi". As we usually use the name "i2c" instead of "twi" in the mainline kernel, change these names to "s_i2c" for consistency. The "s_twi" functions are not yet referenced by any device trees in mainline kernel so I think it's safe to change the name. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: add support of R40 to A10 pinctrl driverIcenowy Zheng2017-08-142-79/+196
| | | | | | | | | | | R40 is said to be an upgrade of A20, and its pin configuration is also similar to A20 (and thus similar to A10). Add support for R40 to the A10 pinctrl driver. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: add a missing function of A10/A20 pinctrl driverIcenowy Zheng2017-07-311-0/+1
| | | | | | | | | | | | | | | | | | | | The PH16 pin has a function with mux id 0x5, which is the DET pin of the "sim" (smart card reader) IP block. This function is missing in old versions of A10/A20 SoCs' datasheets and user manuals, so it's also missing in the old drivers. The newest A10 Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and it's discovered during implementing R40 pinctrl driver. Add it to the driver. As we now merged A20 pinctrl driver to the A10 one, we need to only fix the A10 driver now. Fixes: f2821b1ca3a2 ("pinctrl: sunxi: Move Allwinner A10 pinctrl driver to a driver of its own") Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: Add support for A83T R_PIOChen-Yu Tsai2017-06-093-0/+133
| | | | | | | | | | | The R_PIO on the A83T is almost the same as the one found on the A64, except that the CIR_RX function was moved from pin PL11 to pin PL12. Add a driver for it. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: constify irq_domain_opsTobias Klauser2017-06-091-1/+1
| | | | | | | | | struct irq_domain_ops is not modified, so it can be made const. Suggested-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: drop dedicated A20 driverIcenowy Zheng2017-05-293-1061/+0
| | | | | | | | | | As we added A20 support to A10 pinctrl driver, now we can delete the dedicated A20 pinctrl driver, which is duplicated code. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Chen-Yu Tsai <wens@csie.org> [Drop Makefile entry] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: add A20 support to A10 driverIcenowy Zheng2017-05-292-65/+226
| | | | | | | | | | | As A20 is designed as a pin-compatible upgrade of A10, their pin controller are very similar, and can share one driver. Add A20 support to the A10 driver. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCsIcenowy Zheng2017-05-291-0/+3
| | | | | | | | | | | Allwinner A10, A20 and R40 SoCs have similar GPIO layout. Add SoC definitions in pinctrl-sunxi.h, in order to merge A20 support into A10 driver, and add R40 support into it. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: Fix SPDIF function name for A83TChen-Yu Tsai2017-05-231-1/+1
| | | | | | | | | | | | | We use well known standard names for functions that have name, such as I2C, SPI, SPDIF, etc.. Fix the function name of SPDIF, which was named OWA (One Wire Audio) based on Allwinner datasheets. Fixes: 4730f33f0d82 ("pinctrl: sunxi: add allwinner A83T PIO controller support") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: sunxi: make use of raw_spinlock variantsJulia Cartwright2017-03-162-14/+14
| | | | | | | | | | | | | | The sunxi pinctrl driver currently implement an irq_chip for handling interrupts; due to how irq_chip handling is done, it's necessary for the irq_chip methods to be invoked from hardirq context, even on a a real-time kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT kernels, it is not suitable to be used with irq_chips. A quick audit of the operations under the lock reveal that they do only minimal, bounded work, and are therefore safe to do under a raw spinlock. Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-30 07:41:55 +0000