summaryrefslogtreecommitdiffstats
path: root/drivers/remoteproc/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* remoteproc/wkup_m3: add a remoteproc driver for TI Wakeup M3Dave Gerlach2015-06-171-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Add a remoteproc driver to load the firmware and boot a small Wakeup M3 processor present on TI AM33xx and AM43xx SoCs. This Wakeup M3 remote processor is an integrated Cortex M3 that allows the SoC to enter the lowest possible power state by taking control from the MPU after it has gone into its own low power state and shutting off any additional peripherals. The Wakeup M3 processor has two internal memory regions - 16 kB of unified instruction memory called UMEM used to store executable code, and 8 kB of data memory called DMEM used for all data sections. The Wakeup M3 processor executes its code entirely from within the UMEM and uses the DMEM for any data. It does not use any external memory or any other external resources. The device address view has the UMEM at address 0x0 and DMEM at address 0x80000, and these are computed automatically within the driver based on relative address calculation from the corresponding device tree IOMEM resources. These device addresses are used to aid the core remoteproc ELF loader code to properly translate and load the firmware segments through the .rproc_da_to_va ops. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
* remoteproc/davinci: add a remoteproc driver for OMAP-L13x DSPRobert Tivy2013-04-151-0/+1
| | | | | | | | Adding a new remoteproc driver for OMAP-L13x DSP Signed-off-by: Robert Tivy <rtivy@ti.com> [removed 'EXPERIMENTAL' and fixed some indentation issues] Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
* remoteproc: Add STE modem driverSjur Brændeland2012-09-221-0/+1
| | | | | | | | | | | | | | | | Add support for the STE modem shared memory driver. This driver hooks into the remoteproc framework in order to manage configuration and the virtio devices. This driver adds custom firmware handlers, because STE modem uses a custom firmware layout. Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> cc: Linus Walleij <linus.walleij@linaro.org> cc: Alan Cox <alan@lxorguk.ukuu.org.uk> [ohad: validate mdev->ops, move setup() to probe/remove, trivial style changes] Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
* remoteproc: Move Elf related functions to separate fileSjur Brændeland2012-07-151-0/+1
| | | | | | | | | | | | | | | | | Prepare for introduction of custom firmware loaders by moving all ELF related handling into a separate file. The functions: rproc_find_rsc_table(), rproc_fw_sanity_check(), rproc_find_rsc_table() and rproc_get_boot_addr() are moved to the new file remoteproc_elf_loader.c. The function rproc_da_to_va() is made non-static and is declared in remoteproc_internal.h No functional changes are introduced in this patch. Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com> [ohad: rebase, fix kerneldoc, put prototypes in remoteproc_internal.h] Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
* remoteproc: remoteproc_rpmsg -> remoteproc_virtioOhad Ben-Cohen2012-03-061-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At this point remoteproc can only register a single VIRTIO_ID_RPMSG virtio device. This limitation is going away soon: remoteproc is getting support for registering any number of virtio devices and of any type (as published by the firmware of the remote processor). Rename remoteproc_rpmsg.c to remoteproc_virtio.c in preparation of this generalization work. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Cc: Brian Swetland <swetland@google.com> Cc: Iliyan Malchev <malchev@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Mark Grosen <mgrosen@ti.com> Cc: John Williams <john.williams@petalogix.com> Cc: Michal Simek <monstr@monstr.eu> Cc: Loic PALLARDY <loic.pallardy@stericsson.com> Cc: Ludovic BARRE <ludovic.barre@stericsson.com> Cc: Omar Ramirez Luna <omar.luna@linaro.org> Cc: Guzman Lugo Fernando <fernando.lugo@ti.com> Cc: Anna Suman <s-anna@ti.com> Cc: Clark Rob <rob@ti.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Saravana Kannan <skannan@codeaurora.org> Cc: David Brown <davidb@codeaurora.org> Cc: Kieran Bingham <kieranbingham@gmail.com> Cc: Tony Lindgren <tony@atomide.com>
* remoteproc/omap: add a remoteproc driver for OMAP4Ohad Ben-Cohen2012-02-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a remoteproc driver for OMAP4, so we can boot the dual-M3 and and DSP subsystems. Use the omap_device_* API to control the hardware state, and utilize the OMAP mailbox to interrupt the remote processor when a new message is pending (the mailbox payload is used to tell it which virtqueue was the message placed in). Conversely, when an inbound mailbox message arrives, tell the remoteproc core which virtqueue is triggered. Later we will also use the mailbox payload to signal omap-specific events like remote crashes (which will be used to trigger remoteproc recovery) and power management transitions. At that point we will also extend the remoteproc core to support this. Based on (but now quite far from) work done by Fernando Guzman Lugo <fernando.lugo@ti.com> and Hari Kanigeri <h-kanigeri2@ti.com>. Designed with Brian Swetland <swetland@google.com>. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Acked-by: Tony Lindgren <tony@atomide.com> Cc: Brian Swetland <swetland@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Russell King <linux@arm.linux.org.uk> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <greg@kroah.com> Cc: Stephen Boyd <sboyd@codeaurora.org>
* remoteproc: create rpmsg virtio deviceOhad Ben-Cohen2012-02-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Create an rpmsg virtio device to allow message-based communication with the remote processor (but only if supported by its firmware). There are several advantages to provide this functionality at the remoteproc-level: - to support it, platforms only have to provide their own ->kick() handler; no need to duplicate the rest of the code. - the virtio device is created only when the remote processor is registered and ready to go. No need to depend on initcall magic. moreover, we only add the virtio device if the firmware really supports it, and only after we know the supported virtio device features. - correct device model hierarchy can be set, and that is useful for natural power management and DMA API behavior. - when the remote processor crashes (or removed) we only need to remove the virtio device, and the driver core will take care of the rest. No need to implement any out-of-bound notifiers. - we can now easily bind the virtio device to its rproc handle, and this way we don't need any name-based remoteproc ->get() API. Currently we only support creating a single rpmsg virtio device per remote processor, but later this is going to be extended to support creating numerous virtio devices of other types too (block, net, console...). Designed with Brian Swetland <swetland@google.com>. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Cc: Brian Swetland <swetland@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <greg@kroah.com> Cc: Stephen Boyd <sboyd@codeaurora.org>
* remoteproc: add debugfs entriesOhad Ben-Cohen2012-02-081-0/+1
| | | | | | | | | | | | | | | | | | | | | Expose several remote processor properties (name, state, trace buffer) that are helpful for debugging. This part is extracted to a separate patch just to keep the review load down. Designed with Brian Swetland <swetland@google.com>. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Brian Swetland <swetland@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <greg@kroah.com> Cc: Stephen Boyd <sboyd@codeaurora.org>
* remoteproc: add framework for controlling remote processorsOhad Ben-Cohen2012-02-081-0/+6
Modern SoCs typically employ a central symmetric multiprocessing (SMP) application processor running Linux, with several other asymmetric multiprocessing (AMP) heterogeneous processors running different instances of operating system, whether Linux or any other flavor of real-time OS. Booting a remote processor in an AMP configuration typically involves: - Loading a firmware which contains the OS image - Allocating and providing it required system resources (e.g. memory) - Programming an IOMMU (when relevant) - Powering on the device This patch introduces a generic framework that allows drivers to do that. In the future, this framework will also include runtime power management and error recovery. Based on (but now quite far from) work done by Fernando Guzman Lugo <fernando.lugo@ti.com>. ELF loader was written by Mark Grosen <mgrosen@ti.com>, based on msm's Peripheral Image Loader (PIL) by Stephen Boyd <sboyd@codeaurora.org>. Designed with Brian Swetland <swetland@google.com>. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Brian Swetland <swetland@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <greg@kroah.com> Cc: Stephen Boyd <sboyd@codeaurora.org>