summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/qla2xxx/qla_fw.h
Commit message (Collapse)AuthorAgeFilesLines
* [SCSI] qla2xxx: Query supported RISC registers bits in determining a ↵Andrew Vasquez2009-06-081-1/+0
| | | | | | | | | paused-state. ISP24xx and above must query the host-status register, not HCCR. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Fallback to 'golden-firmware' operation on supported ISPs.Andrew Vasquez2009-06-081-0/+1
| | | | | | | | | | In case the onboard firmware is unable to be read or loaded for operation, attempt to fallback to a limited-operational firmware image stored in a different flash region. This will allow a user to reflash and correct a board with proper operational firmware. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Export TLV data on supported ISPs.Andrew Vasquez2009-06-081-0/+1
| | | | | | | Firmware currently provides PB and PGF TLVs. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Export XGMAC statistics on supported ISPs.Andrew Vasquez2009-06-081-0/+1
| | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Correct hard-coded address of a second-port's NVRAM.Harish Zunjarrao2009-05-201-1/+1
| | | | | | Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com> Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Always use an FLT's NVRAM/VPD region information.Andrew Vasquez2009-04-031-0/+4
| | | | | | | | Rather than assuming a particular layout of the data. Applies to recent ISPs only. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add reset capabilities for application support.Lalit Chandivade2009-04-031-0/+1
| | | | | | | Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com> Additional cleanups and Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add Flash-Access-Control support for recent ISPs.Joe Carnuccio2009-04-031-0/+14
| | | | | | | | | | | | | Given the low-level interface varies from one flash-part manufacturer to the next, the Flash-Access-Control (FAC) mailbox command makes the specific flash type transparent to the driver by encapsulating a basic set of accessor and update routines. Use these new routines where applicable by querying FAC opcode get-sector-size at init-time. Additional cleanups and Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Pass in optional extended-initialization control block.Andrew Vasquez2009-04-031-1/+22
| | | | | | | Recent ISPs use this data to configure FCF information. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Properly acknowledge IDC notification messages.Andrew Vasquez2009-02-101-0/+2
| | | | | | | | | | | | | To ensure smooth operations amongst the FCoE and NIC side components of the ISP81xx chip, the FCoE driver (qla2xxx) must ensure the 10gb NIC driver (qlge) does not timeout waiting for IDC (Inter-Driver Communication) acknowledgments. The acknowledgment requirements are trivial -- a simple mirroring of incoming mailbox registers during the AEN to a process-context capable mailbox command. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add ISP81XX support.Andrew Vasquez2009-01-071-3/+291
| | | | | | | Codes to support new FCoE boards. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: add support for multi-queue adapterAnirban Chakraborty2008-12-291-5/+9
| | | | | | | | | | | | | | | | | | Following changes have been made. 1. qla_hw_data structure holds an array for request queue pointers, and an array for response queue pointers. 2. The base request and response queues are created by default. 3. Additional request and response queues are created at the time of vport creation. If queue resources are exhausted during vport creation, newly created vports use the default queue. 4. Requests are sent to the request queue that the vport was assigned in the beginning. 5. Responses are completed on the response queue with which the request queue is associated with. [fixup memcpy argument reversal spotted by davej@redhat.com] Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add NPIV-Config Table support.Andrew Vasquez2008-10-031-0/+26
| | | | | | | | To instatiate pre-configured vport entities defined within an HBA's flash memory. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add Flash Layout Table support.Andrew Vasquez2008-10-031-5/+40
| | | | | | | | | | | The Flash Layout Table (FLT) present on many recent HBAs encodes flash usage information, organizes data stored into separate regions and presents the information uniformly to the driver. Use this information rather than using specific hard-coded values based on ISP type. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Correct misc. endian and byte-ordering issues.Seokmann Ju2008-04-271-21/+5
| | | | | | | | | There were several places in the driver which could cause byte ordering problem as provided by Al Viro <viro@ZenIV.linux.org.uk>. Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add ISP84XX support.Harihara Kadayam2008-04-071-0/+123
| | | | | | | Signed-off-by: Ravi Anand <ravi.anand@qlogic.com> Additional cleanups and Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add midlayer target/device reset support.Andrew Vasquez2008-04-071-1/+1
| | | | | | | | | | | | | | | | Now that infrastructure is present within the midlayer and there is a clear distinction between what is expected from a device and target reset, convert the current device-reset codes to a target-reset, and add codes to perform a proper device-reset (LUN reset). In the process of adding reset support, collapse and consolidate large sections of mailbox-command (TMF issuance) codes, generalize the two 'wait-for-commands-to-complete' functions, and add a generic-reset routine for use by midlayer reset functions. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add Flash Descriptor Table layout support.Andrew Vasquez2008-04-071-0/+32
| | | | | | | | | | | The Flash Descriptor Table (FDT) present on many recent HBAs encodes flash accessing characteristics of the flash-part used on the HBA. Use this information during flash manipulation (writes) rather than using specific hard-coded values based on queried manufacturer and device IDs. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add hardware trace-logging support.Andrew Vasquez2008-04-071-1/+13
| | | | | | | | | | Recent ISPs have a region within FLASH which acts as a repository for the logging of serious hardware and software failures. Currently, the region is large enough to support up to 255 entries. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Update copyright banner.Andrew Vasquez2008-04-071-1/+1
| | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Add Fibre Channel Event (FCE) tracing support.Andrew Vasquez2008-01-231-0/+7
| | | | | | | | | | | | | | | | | | | | | FCE support enables the firmware to record FC extended link services and basic link services frames which have been transmitted and received by the ISP. This allows for a limited view of the FC traffic through the ISP without using a FC analyzer. This can be useful in situations where a physical connection to the FC bus is not possible. The driver exports this information in two ways -- first, via a debugfs node exported for all supported ISPs under: <debugfs_mount_point>/qla2xxx/qla2xxx_<host_no>/fce where a read of the 'fce' file will provide a snapshot of the firmware's FCE buffer; and finally, the FCE buffer will be extracted during a firmware-dump scenario. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Trace-Control naming cleanups.Andrew Vasquez2008-01-231-0/+7
| | | | | | | In preparation for FCE (Fibre Channel Event) tracing support. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Correct NPIV support for recent ISPs.Andrew Vasquez2008-01-111-6/+10
| | | | | | | | | | Firmware will export to software the maximum number of vports supported for any given firmware version and ISP type. Use this information rather than the current hardcoding of limitations within the driver. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] qla2xxx: Query additional RISC registers during ISP25XX firmware dump.Andrew Vasquez2007-10-121-1/+1
| | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Query additional RISC information during a pause.Andrew Vasquez2007-10-121-1/+3
| | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Allow region-based flash-part accesses.Joe Carnuccio2007-10-121-0/+2
| | | | | | Additional cleanups and Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Add ISP25XX support.Andrew Vasquez2007-07-201-3/+33
| | | | | | | | Large code-reuse from ISP24xx, consolidate RISC memory extraction routines during firmware-dump. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: add support for NPIVSeokmann Ju2007-07-141-12/+79
| | | | | | | | | | | Following patch adds support for NPIV (N-Port ID Virtualization) to the qla2xxx. - supported within switched-fabric topologies only. - supports up to 63 virtual ports on each physical port. Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Correctly set the firmware NOS/OLS timeout during ↵Andrew Vasquez2006-06-261-1/+1
| | | | | | | | | | initialization. Original code incorrectly assigned it to the driver's link-down-timeout value (a value in seconds). Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Add NVRAM 'Disable Serdes' bit support.Andrew Vasquez2006-06-261-1/+1
| | | | | | | | | The host section of ISP24xx NVRAMs contain a new bit which allows a user to selectively disable ports of an HBA. These ports (hosts) will not be presented to the midlayer. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Remove obsolete firmware-loader-module support.Andrew Vasquez2006-05-201-1/+0
| | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Use FW calculated residual count for underrun handling.Ravi Anand2006-05-201-1/+1
| | | | | | | With ISP24XX and ISP54XX parts. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Add VPD sysfs attribute.andrew.vasquez@qlogic.com2006-03-121-1/+1
| | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Update license.Andrew Vasquez2005-10-281-20/+6
| | | | | Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Use midlayer's int_to_scsilun() function.Andrew Vasquez2005-10-281-2/+2
| | | | | | | While populating command type 6 and 7 IOCBs. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Update copyright banner.Andrew Vasquez2005-07-141-1/+1
| | | | | | | Update copyright banner. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Code scrubbing.Andrew Vasquez2005-07-141-3/+0
| | | | | | | | | | | Code scrubbing. - Remove trailing whitespace from driver files. - Remove unused #defines and inlines. - Standardize on C comments (// -> /* */) Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] qla2xxx: Add ISP24xx definitions.Andrew Vasquez2005-07-141-0/+1076
Add ISP24xx definitions. Add requisite structure definitions and #define's for ISP24xx support. Also drop volatile modifiers from device_reg_* register layouts as the members are never really accessed, only their offsets within the layout are used during reads and writes. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-26 09:08:31 +0000