summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/stex.c
Commit message (Collapse)AuthorAgeFilesLines
* [SCSI] add use_sg_chaining option to scsi_host_templateFUJITA Tomonori2007-10-161-0/+1
| | | | | | | | | | This option is true if a low-level driver can support sg chaining. This will be removed eventually when all the drivers are converted to support sg chaining. q->max_phys_segments is set to SCSI_MAX_SG_SEGMENTS if false. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* [SCSI] stex: use resid for xfer len informationEd Lin2007-07-141-2/+2
| | | | | | | | The original implementation in stex_ys_commands() is inappropriate. For xfer len information, we should use resid instead. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] Merge up to linux-2.6 headJames Bottomley2007-05-301-36/+54
|\ | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/scsi/jazz_esp.c Same changes made by both SCSI and SPARC trees: problem with UTF-8 conversion in the copyright. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] stex: minor cleanup and version updateEd Lin2007-05-161-3/+13
| | | | | | | | | | | | | | | | | | Add debug information into abort and host_reset routine. Change ioremap to ioremap_nocache. Version updated to 3.6.0000.1. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] stex: fix reset recovery for console deviceEd Lin2007-05-161-0/+7
| | | | | | | | | | | | | | | | | | | | | | After reset completed, the scsi error handler sends out TEST_UNIT_READY to the device. For 'normal' devices the command will be handled by firmware. However, because the RAID console only interfaces to scsi mid layer, the firmware will not process the command for it. This will make the console to be offlined right after reset. Add the handling in driver to fix this problem. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] stex: extend hard reset wait timeEd Lin2007-05-161-1/+6
| | | | | | | | | | | | | | | | | | During hard bus reset of st_shasta controllers, 1 ms is not enough for 16-port controllers, although it's good for 8-port controllers. Extend the wait time to 100 ms to allow bus resets finish successfully. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
| * [SCSI] stex: fix id mapping issueEd Lin2007-05-161-32/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The correct internal mapping of stex controllers should be: id:0~15, lun:0~7 (st_shasta) id:0, lun:0~127 (st_yosemite) id:0~127, lun:0 (st_vsc and st_vsc1) This patch reports the internal mapping to scsi mid layer, eliminating the translation between scsi mid layer and firmware. To achieve this goal, we also need to: -- fail the REPORT_LUNS command for st_shasta because the firmware is known to not report all actual luns -- add an entry in scsi_devindo.c to force sequential lun scan (for st_shasta controllers) -- fail the REPORT_LUNS command for console device -- remove special handling of REPORT_LUNS command for st_yosemite, as there is no translation mapping now Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* | [SCSI] stex: convert to use the data buffer accessorsFUJITA Tomonori2007-05-291-73/+36
|/ | | | | | | | | | | - remove the unnecessary map_single path. - convert to use the new accessors for the sg lists and the parameters. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [PATCH] remove many unneeded #includes of sched.hTim Schmielau2007-02-141-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | After Al Viro (finally) succeeded in removing the sched.h #include in module.h recently, it makes sense again to remove other superfluous sched.h includes. There are quite a lot of files which include it but don't actually need anything defined in there. Presumably these includes were once needed for macros that used to live in sched.h, but moved to other header files in the course of cleaning it up. To ease the pain, this time I did not fiddle with any header files and only removed #includes from .c-files, which tend to cause less trouble. Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha, arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig, allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all configs in arch/arm/configs on arm. I also checked that no new warnings were introduced by the patch (actually, some warnings are removed that were emitted by unnecessarily included header files). Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [SCSI] stex: version updateEd Lin2006-12-051-4/+2
| | | | | | | Update version to 3.1.0.1 Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: change wait loop codeEd Lin2006-12-051-21/+20
| | | | | | | | | The original wait loop may be much longer than intended time. Use more accurate timer_after for it. Also adjust wait value to avoid unnecessary long waiting. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: add new device type supportEd Lin2006-12-051-7/+21
| | | | | | | | Add support for st_vsc1 type device (st_vsc is ok because it does not require extra buffer). Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: update device id infoEd Lin2006-12-051-9/+26
| | | | | | | | | | | - add comments for various devices - remove unused device ids(0xf350, 0x4301, 0x8301, 0x8302) - add new device id(0xe350) - fix vendor id of st_vsc - modify Kconfig help info Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: adjust default queue lengthEd Lin2006-12-051-1/+10
| | | | | | | | Firmware of new version may adjust default queue length. It is backward compatible. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: add value check in hard reset routineEd Lin2006-12-051-1/+1
| | | | | | | During hard reset, an all-1 value from PCI_COMMAND should be invalid. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: fix controller_info command handlingEd Lin2006-12-051-0/+1
| | | | | | | | This command needs information from both firmware and driver. First copy information from firmware to buffer, then fill in driver information. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: fix biosparam calculationEd Lin2006-12-051-3/+3
| | | | | | | Fix biosparam calculation. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* IRQ: Maintain regs pointer globally rather than passing to IRQ handlersDavid Howells2006-10-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* [SCSI] stex: add new device (id 0x8650) supportEd Lin2006-10-011-30/+164
| | | | | | | | | | | | | A new device (id 0x8650, nickname 'yosemite') support is added. It's basically the same, except for following items: - mapping of id and lun by firmware - special handling for some commands in interrupt routine - change of internal copy function for these special commands - different reset handling code - different shutdown notification command Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: cancel unused field in struct req_msgEd Lin2006-10-011-2/+1
| | | | | | | | | | The payload_sz field in struct req_msg is not big enough to indicate the size of req_msg, as its type is u8. It is confirmed that this field is not used by firmware, so cancel it here. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] add failure return to scsi_init_shared_tag_map()James Bottomley2006-09-021-3/+2
| | | | | | And use it in the stex driver. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] stex: add shared tags from blockEd Lin2006-09-021-120/+57
| | | | | | | | | Use block shared tags entirely within the driver. In the case of shutdown, assume that there are no other outstanding commands, so tag 0 is fine. Signed-off-by: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* [SCSI] Add Promise SuperTrak driverJeff Garzik2006-09-021-0/+1316
Add Promise SuperTrak 'stex' driver, supporting SuperTrak EX8350/8300/16350/16300 controllers. The controller's firmware accepts SCSI commands, handing them to the underlying RAID or JBOD disks. The driver consisted of the following cleanups and fixes, beyond its initial submission: Ed Lin: stex: cleanup and minor fixes stex: add new device ids stex: update internal copy code path stex: add hard reset function stex: adjust command timeout in slave_config routine stex: use more efficient method for unload/shutdown flush Jeff Garzik: [SCSI] Add Promise SuperTrak 'shasta' driver. Rename drivers/scsi/shasta.c to stex.c ("SuperTrak EX"). [SCSI] stex: update with community comments from 'Promise SuperTrak' thread [SCSI] stex: Fix warning, trim trailing whitespace. [SCSI] stex: remove last remnants of "shasta" project code name [SCSI] stex: removed 6-byte command emulation [SCSI] stex: minor cleanups [SCSI] stex: minor fixes: irq flag, error return value [SCSI] stex: use dma_alloc_coherent() Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-28 08:09:39 +0000