summaryrefslogtreecommitdiffstats
path: root/drivers/spi/spi.c
Commit message (Collapse)AuthorAgeFilesLines
*-. Merge remote-tracking branches 'spi/topic/sunxi', 'spi/topic/tegra114', ↵Mark Brown2014-03-301-1/+11
|\ \ | | | | | | | | | 'spi/topic/ti-qspi', 'spi/topic/ti-ssp', 'spi/topic/topcliff-pch', 'spi/topic/txx9', 'spi/topic/xcomm' and 'spi/topic/xfer' into spi-next
| | * spi: Add a timeout when waiting for transfersMark Brown2014-02-031-1/+11
| |/ | | | | | | | | | | | | Don't wait indefinitely for transfers to complete but time out after 10ms more than we expect the transfer to take on the wire. Signed-off-by: Mark Brown <broonie@linaro.org>
| |
| \
*-. \ Merge remote-tracking branches 'spi/topic/bus-num', 'spi/topic/cleanup', ↵Mark Brown2014-03-301-0/+3
|\ \ \ | | |/ | |/| | | | 'spi/topic/clps711x', 'spi/topic/coldfire', 'spi/topic/completion' and 'spi/topic/davinci' into spi-next
| | * spi: core: Set max_speed_hz of spi_device default to max_speed_hz of controllerAxel Lin2014-02-101-0/+3
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In __spi_validate(), xfer->speed_hz is set to be spi->max_speed_hz if it is not set for this transfer. However, if spi->max_speed_hz is also not set, xfer->speed_hz is 0. Some drivers (e.g. au1550, tegra114, tegra20-sflash, tegra20-slink, etc.) then use below code to avoid setting xfer->speed_hz to 0. /* Set speed to the spi max fequency if spi device has not set */ spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency; Let's handle it in spi core. If spi->max_speed_hz is not set, make it default to spi->master->max_speed_hz. So In __spi_validate() if both xfer->speed_hz and spi->max_speed_hz are not set, xfer->speed_hz will be set to spi->master->max_speed_hz. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
* | Merge remote-tracking branch 'spi/topic/dma' into spi-nextMark Brown2014-03-301-0/+180
|\ \
| * | spi: Make max_tx and max_rx the same typeMark Brown2014-02-121-1/+1
| | | | | | | | | | | | | | | | | | Prevents spurious compiler warnings. Signed-off-by: Mark Brown <broonie@linaro.org>
| * | spi: Make core DMA mapping functions generate scatterlistsMark Brown2014-02-041-25/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We cannot unconditionally use dma_map_single() to map data for use with SPI since transfers may exceed a page and virtual addresses may not be provided with physically contiguous pages. Further, addresses allocated using vmalloc() need to be mapped differently to other addresses. Currently only the MXS driver handles all this, a few drivers do handle the possibility that buffers may not be physically contiguous which is the main potential problem but many don't even do that. Factoring this out into the core will make it easier for drivers to do a good job so if the driver is using the core DMA code then generate a scatterlist instead of mapping to a single address so do that. This code is mainly based on a combination of the existing code in the MXS and PXA2xx drivers. In future we should be able to extend it to allow the core to concatenate adjacent transfers if they are compatible, improving performance. Currently for simplicity clients are not allowed to use the scatterlist when they do DMA mapping, in the future the existing single address mappings will be replaced with use of the scatterlist most likely as part of pre-verifying transfers. This change makes it mandatory to use scatterlists when using the core DMA mapping so update the s3c64xx driver to do this when used with dmaengine. Doing so makes the code more ugly but it is expected that the old s3c-dma code can be removed very soon. Signed-off-by: Mark Brown <broonie@linaro.org>
| * | spi: Provide core support for full duplex devicesMark Brown2014-02-041-0/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is fairly common for SPI devices to require that one or both transfer directions is always active. Currently drivers open code this in various ways with varying degrees of efficiency. Start factoring this out by providing flags SPI_MASTER_MUST_TX and SPI_MASTER_MUST_RX. These will cause the core to provide buffers for the requested direction if none are specified in the underlying transfer. Currently this is fairly inefficient since we actually allocate a data buffer which may get large, support for mapping transfers using a scatterlist will allow us to avoid this for DMA based transfers. Signed-off-by: Mark Brown <broonie@linaro.org>
| * | spi: Provide core support for DMA mapping transfersMark Brown2014-02-031-0/+82
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The process of DMA mapping buffers for SPI transfers does not vary between devices so in order to save duplication of code in drivers this can be factored out into the core, allowing it to be integrated with the work that is being done on factoring out the common elements from the data path including more sharing of dmaengine code. In order to use this masters need to provide a can_dma() operation and while the hardware is prepared they should ensure that DMA channels are provided in tx_dma and rx_dma. The core will then ensure that the buffers are mapped for DMA prior to calling transfer_one_message(). Currently the cleanup on error is not complete, this needs to be improved. Signed-off-by: Mark Brown <broonie@linaro.org>
* | Merge remote-tracking branch 'spi/topic/core' into spi-nextMark Brown2014-03-301-18/+28
|\ \
| * | spi: Do not require a completionMark Brown2014-03-251-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | There is no real reason why we require transfers to have a completion and the only user of the completion now checks to see if one has been provided before using it so stop enforcing this. This makes it more convenient for drivers to chain multiple asynchronous transfers together. Signed-off-by: Mark Brown <broonie@linaro.org>
| * | spi: core: Use master->max_speed_hz as transfer speed when xfer->speed_hz > ↵Axel Lin2014-03-171-8/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master->max_speed_hz When xfer->speed_hz is greater than master->max_speed_hz, it's generally safe to use master->max_speed_hz as transfer speed. Thus use master->max_speed_hz as transfer speed rather than return error when xfer->speed_hz > master->max_speed_hz. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Mark Brown <broonie@linaro.org>
| * | spi: core: make zero length transfer valid againAtsushi Nemoto2014-03-041-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zero length transfer becomes invalid since "spi: core: Validate length of the transfers in message" commit, but it should be valid to support an odd device, for example, which requires long delay between chipselect and the first transfer, etc. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| * | spi: core: Replace msleep with usleep_range to get more accurate sleep timeAxel Lin2014-02-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes below checkpatch warning: WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt + msleep(10); Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| * | spi: core: Validate length of the transfers in messageIvan T. Ivanov2014-02-221-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | SPI transfer length should be multiple of SPI word size, where SPI word size should be power-of-two multiple Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| * | spi: Clean up probe and remove functionsJean Delvare2014-02-141-7/+5
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While backporting 33cf00e5 ("spi: attach/detach SPI device to the ACPI power domain"), I noticed that the code changes were suboptimal: * Why use &spi->dev when we have dev at hand? * After fixing the above, spi is used only once, so we don't really need a local variable for it. This results in the following clean-up. Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
* | Merge remote-tracking branch 'spi/fix/core' into spi-linusMark Brown2014-03-301-3/+3
|\ \
| * | spi: Fix handling of cs_change in core implementationMark Brown2014-03-301-3/+3
| |/ | | | | | | | | | | | | | | | | | | | | The core implementation of cs_change didn't follow the documentation which says that cs_change in the middle of the transfer means to briefly deassert chip select, instead it followed buggy drivers which change the polarity of chip select. Use a delay of 10us between deassert and reassert simply from pulling numbers out of a hat. Reported-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
* | Merge remote-tracking branch 'spi/fix/core' into spi-linusMark Brown2014-02-111-3/+1
|\ \ | |/ |/|
| * spi: Fix crash with double message finalisation on error handlingGeert Uytterhoeven2014-01-281-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit e120cc0dcf2880a4c5c0a6cb27b655600a1cfa1d. It causes a NULL pointer dereference with drivers using the generic spi_transfer_one_message(), which always calls spi_finalize_current_message(), which zeroes master->cur_msg. Drivers implementing transfer_one_message() theirselves must always call spi_finalize_current_message(), even if the transfer failed: * @transfer_one_message: the subsystem calls the driver to transfer a single * message while queuing transfers that arrive in the meantime. When the * driver is finished with this message, it must call * spi_finalize_current_message() so the subsystem can issue the next * transfer Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
* | Merge tag 'spi-v3.14-2' of ↵Linus Torvalds2014-01-251-28/+46
|\| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Pull spi updates from Mark Brown: "A respun version of the merges for the pull request previously sent with a few additional fixes. The last two merges were fixed up by hand since the branches have moved on and currently have the prior merge in them. Quite a busy release for the SPI subsystem, mostly in cleanups big and small scattered through the stack rather than anything else: - New driver for the Broadcom BC63xx HSSPI controller - Fix duplicate device registration for ACPI - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA changes upon which the transiton depends) - Some small optimisations to reduce the amount of time we hold locks in the datapath, eliminate some redundant checks and the size of a spi_transfer - Lots of fixes, cleanups and general enhancements to drivers, especially the rspi and Atmel drivers" * tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits) spi: core: Fix transfer failure when master->transfer_one returns positive value spi: Correct set_cs() documentation spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer() spi: Spelling s/finised/finished/ spi: sc18is602: Convert to use bits_per_word_mask spi: Remove duplicate code to set default bits_per_word setting spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP spi: clps711x: Add MODULE_ALIAS to support module auto-loading spi: rspi: Add missing clk_disable() calls in error and cleanup paths spi: rspi: Spelling s/transmition/transmission/ spi: rspi: Add support for specifying CPHA/CPOL spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match spi: rspi: Add more QSPI register documentation spi: rspi: Add more RSPI register documentation spi: rspi: Remove dependency on DMAE for SHMOBILE spi/s3c64xx: Correct indentation spi: sh: Use spi_sh_clear_bit() instead of open-coded spi: bitbang: Grammar s/make to make/to make/ spi: sh-hspi: Spelling s/recive/receive/ spi: core: Improve tx/rx_nbits check comments ...
| * Merge remote-tracking branch 'spi/topic/core' into spi-linusMark Brown2014-01-231-20/+26
| |\
| | * spi: core: Improve tx/rx_nbits check commentsGeert Uytterhoeven2014-01-131-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Rephrase the comments about tx/rx_nbits validity checks, - Remove the stale comment about SPI_3WIRE (the code it refers to was removed in commit 368ca4e0c75612c0a4d6bbcef7efb944604340c2 ("spi: Eliminate 3WIRE spi_transfer check")). Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
| | * spi: core: Use list_first_entry to extract head of queueAxel Lin2014-01-091-1/+1
| | | | | | | | | | | | | | | | | | | | | For slightly better readability. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| | * spi: core: Use list_first_entry_or_null() instead of open-codedAxel Lin2014-01-021-5/+2
| | | | | | | | | | | | | | | | | | | | | Use list_first_entry_or_null() to save a few lines. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| | * spi: Eliminate 3WIRE spi_transfer checkTrent Piepho2013-12-301-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Checking for SPI_3WIRE isn't needed. spi_setup() already prevents 3WIRE mode from being combined with DUAL or QUAD mode support. So there is no need to differentiate between a single bit device with SPI_3WIRE set and one with without. It doesn't change the allowed bit widths. Signed-off-by: Trent Piepho <tpiepho@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| | * spi: Factor validation and initialisation of messages outside lockMark Brown2013-11-241-5/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently we do a bunch of per-message validation and initialisation in __spi_async() which is called with the bus lock held. Since none of this validation depends on the current bus status there's no need to hold the lock to do it so split it out into a separate __spi_validate() function which is called prior to taking the bus lock. This could be slightly neater but keep things simple for now to show the code motion clearly. Based on observations from Martin Sperl. Signed-off-by: Mark Brown <broonie@linaro.org>
| * | Merge remote-tracking branch 'spi/fix/core' into spi-linusMark Brown2014-01-231-8/+20
| |\ \
| | * | spi: core: Fix transfer failure when master->transfer_one returns positive valueAxel Lin2014-01-211-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master->transfer_one returns positive value is not a error. So set ret to 0 when master->transfer_one returns positive value. Otherwise, I hit "spi_master spi0: failed to transfer one message from queue" error when my transfer_one callback returns 1. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| | * | spi: Spelling s/finised/finished/Geert Uytterhoeven2014-01-211-1/+1
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by: Mark Brown <broonie@linaro.org>
| | * | spi: Check conflicting CS based on spi->chip_select instead of device nameMika Westerberg2014-01-091-5/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit e13ac47bec20 (spi: Use stable dev_name for ACPI enumerated SPI slaves) changed the SPI device naming to be based on ACPI device name instead of carrying bus number and chip select for devices enumerated from ACPI namespace. In case of a buggy BIOS that lists multiple SPI devices sharing the same chip select (even though they should use different) the current code fails to detect that and allows the devices to be added to the bus. Fix this by walking through the bus and comparing spi->chip_select instead of device name. This should work regardless what the device name will be in future. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| | * | spidev: fix hang when transfer_one_message failsDaniel Santos2014-01-061-1/+3
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This corrects a problem in spi_pump_messages() that leads to an spi message hanging forever when a call to transfer_one_message() fails. This failure occurs in my MCP2210 driver when the cs_change bit is set on the last transfer in a message, an operation which the hardware does not support. Rationale Since the transfer_one_message() returns an int, we must presume that it may fail. If transfer_one_message() should never fail, it should return void. Thus, calls to transfer_one_message() should properly manage a failure. Fixes: ffbbdd21329f3 (spi: create a message queueing infrastructure) Signed-off-by: Daniel Santos <daniel.santos@pobox.com> Signed-off-by: Mark Brown <broonie@linaro.org> Cc: stable@vger.kernel.org
* | / ACPI: fix module autoloading for ACPI enumerated devicesZhang Rui2014-01-161-0/+10
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ACPI enumerated devices has ACPI style _HID and _CID strings, all of these strings can be used for both driver loading and matching. Currently, in Platform, I2C and SPI bus, the ACPI style driver matching is supported by invoking acpi_driver_match_device() in bus .match() callback. But, the module autoloading is still broken. For example, there is any ACPI device with _HID "INTABCD" that is enumerated to platform bus, and we have a driver that can probe it. The driver exports its module_alias as "acpi:INTABCD" use the following code static const struct acpi_device_id xxx_acpi_match[] = { { "INTABCD", 0 }, { } }; MODULE_DEVICE_TABLE(acpi, xxx_acpi_match); But, unfortunately, the device' modalias is shown as "platform:INTABCD:00", please refer to modalias_show() and platform_uevent() in drivers/base/platform.c. This results in that the driver will not be loaded automatically when the device node is created, because their modalias do not match. This also applies to I2C and SPI bus. With this patch, the device' modalias will be shown as "acpi:INTABCD" as well. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Acked-by: Mark Brown <broonie@linaro.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* | Merge remote-tracking branch 'spi/fix/core' into spi-linusMark Brown2013-11-281-1/+1
|\ \ | |/ |/|
| * spi: core: invert success test in devm_spi_register_masterStephen Warren2013-11-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | devres_add() should be called when the action to be undone succeeded, not when it failed. Fix the inverted test in devm_spi_register_master() which was doing the opposite. The user-visible issue without this fix is: insmod spi-tegra114.ko Assume there's an MTD device on that SPI bus, which creates /dev/mtd0. rmmod spi-tegra114 Doesn't remove devices on the SPI bus. insmod spi-tegra114.ko Creates a duplicate SPI device which creates /dev/mtd1. hexdump -C /dev/mtd0 That's the old device, which uses an SPI bus hosted by a non-existent module, which causes the oops below. Unable to handle kernel paging request at virtual address bf0017c0 pgd = c0004000 [bf0017c0] *pgd=ad51b811, *pte=00000000, *ppte=00000000 Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM ... PC is at 0xbf0017c0 LR is at spi_pump_messages+0x15c/0x204 pc : [<bf0017c0>] lr : [<c02f0af8>] psr: 60000113 ... Fixes: 666d5b4c742b ("spi: core: Add devm_spi_register_master()") Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
* | Merge tag 'pm+acpi-2-3.13-rc1' of ↵Linus Torvalds2013-11-201-4/+15
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more ACPI and power management updates from Rafael Wysocki: - ACPI-based device hotplug fixes for issues introduced recently and a fix for an older error code path bug in the ACPI PCI host bridge driver - Fix for recently broken OMAP cpufreq build from Viresh Kumar - Fix for a recent hibernation regression related to s2disk - Fix for a locking-related regression in the ACPI EC driver from Puneet Kumar - System suspend error code path fix related to runtime PM and runtime PM documentation update from Ulf Hansson - cpufreq's conservative governor fix from Xiaoguang Chen - New processor IDs for intel_idle and turbostat and removal of an obsolete Kconfig option from Len Brown - New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg - Removal of several ACPI video DMI blacklist entries that are not necessary any more from Aaron Lu - Rework of the ACPI companion representation in struct device and code cleanup related to that change from Rafael J Wysocki, Lan Tianyu and Jarkko Nikula - Fixes for assigning names to ACPI-enumerated I2C and SPI devices from Jarkko Nikula * tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits) PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed() ACPI / PCI root: Clear driver_data before failing enumeration ACPI / hotplug: Fix PCI host bridge hot removal ACPI / hotplug: Fix acpi_bus_get_device() return value check cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs() ACPI / video: clean up DMI table for initial black screen problem ACPI / EC: Ensure lock is acquired before accessing ec struct members PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps() ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac spi: Use stable dev_name for ACPI enumerated SPI slaves i2c: Use stable dev_name for ACPI enumerated I2C slaves ACPI: Provide acpi_dev_name accessor for struct acpi_device device name ACPI / bind: Use (put|get)_device() on ACPI device objects too ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node cpufreq: OMAP: Fix compilation error 'r & ret undeclared' PM / Runtime: Fix error path for prepare PM / Runtime: Update documentation around probe|remove|suspend cpufreq: conservative: set requested_freq to policy max when it is over policy max ...
| * | spi: Use stable dev_name for ACPI enumerated SPI slavesJarkko Nikula2013-11-141-3/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current spi bus_num.chip_select "spix.y" based device naming scheme may not be stable enough to be used in name based matching, for instance within ALSA SoC subsystem. This can be problem in PC kind of platforms if there are changes in SPI bus configuration, amount of busses or probe order. This patch addresses the problem by using the ACPI device name with "spi-" prefix for ACPI enumerated SPI slave. For them device name "spix.y" becomes "spi-INTABCD:ij". Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Mark Brown <broonie@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
| * | ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_nodeRafael J. Wysocki2013-11-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modify struct acpi_dev_node to contain a pointer to struct acpi_device associated with the given device object (that is, its ACPI companion device) instead of an ACPI handle corresponding to it. Introduce two new macros for manipulating that pointer in a CONFIG_ACPI-safe way, ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the ACPI_HANDLE() macro to take the above changes into account. Drop the ACPI_HANDLE_SET() macro entirely and rework its users to use ACPI_COMPANION_SET() instead. For some of them who used to pass the result of acpi_get_child() directly to ACPI_HANDLE_SET() introduce a helper routine acpi_preset_companion() doing an equivalent thing. The main motivation for doing this is that there are things represented by struct acpi_device objects that don't have valid ACPI handles (so called fixed ACPI hardware features, such as power and sleep buttons) and we would like to create platform device objects for them and "glue" them to their ACPI companions in the usual way (which currently is impossible due to the lack of valid ACPI handles). However, there are more reasons why it may be useful. First, struct acpi_device pointers allow of much better type checking than void pointers which are ACPI handles, so it should be more difficult to write buggy code using modified struct acpi_dev_node and the new macros. Second, the change should help to reduce (over time) the number of places in which the result of ACPI_HANDLE() is passed to acpi_bus_get_device() in order to obtain a pointer to the struct acpi_device associated with the given "physical" device, because now that pointer is returned by ACPI_COMPANION() directly. Finally, the change should make it easier to write generic code that will build both for CONFIG_ACPI set and unset without adding explicit compiler directives to it. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
* | | tree-wide: use reinit_completion instead of INIT_COMPLETIONWolfram Sang2013-11-151-1/+1
|/ / | | | | | | | | | | | | | | | | | | | | | | Use this new function to make code more comprehensible, since we are reinitialzing the completion, not initializing. [akpm@linux-foundation.org: linux-next resyncs] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | Merge tag 'pm+acpi-3.13-rc1' of ↵Linus Torvalds2013-11-141-2/+16
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI and power management updates from Rafael J Wysocki: - New power capping framework and the the Intel Running Average Power Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan. - Addition of the in-kernel switching feature to the arm_big_little cpufreq driver from Viresh Kumar and Nicolas Pitre. - cpufreq support for iMac G5 from Aaro Koskinen. - Baytrail processors support for intel_pstate from Dirk Brandewie. - cpufreq support for Midway/ECX-2000 from Mark Langsdorf. - ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha. - ACPI power management support for the I2C and SPI bus types from Mika Westerberg and Lv Zheng. - cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat, Stratos Karafotis, Xiaoguang Chen, Lan Tianyu. - cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev. - intel_pstate updates from Dirk Brandewie and Adrian Huang. - ACPICA update to version 20130927 includig fixes and cleanups and some reduction of divergences between the ACPICA code in the kernel and ACPICA upstream in order to improve the automatic ACPICA patch generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh Bhat, Bjorn Helgaas, David E Box. - ACPI IPMI driver fixes and cleanups from Lv Zheng. - ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang Yanfei, Rafael J Wysocki. - Conversion of the ACPI AC driver to the platform bus type and multiple driver fixes and cleanups related to ACPI from Zhang Rui. - ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu, Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki. - Fixes and cleanups and new blacklist entries related to the ACPI video support from Aaron Lu, Felipe Contreras, Lennart Poettering, Kirill Tkhai. - cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi. - cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han, Bartlomiej Zolnierkiewicz, Prarit Bhargava. - devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe. - Operation Performance Points (OPP) core updates from Nishanth Menon. - Runtime power management core fix from Rafael J Wysocki and update from Ulf Hansson. - Hibernation fixes from Aaron Lu and Rafael J Wysocki. - Device suspend/resume lockup detection mechanism from Benoit Goby. - Removal of unused proc directories created for various ACPI drivers from Lan Tianyu. - ACPI LPSS driver fix and new device IDs for the ACPI platform scan handler from Heikki Krogerus and Jarkko Nikula. - New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa. - Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter, Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause, Liu Chuansheng. - Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding, Jean-Christophe Plagniol-Villard. * tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits) cpufreq: conservative: fix requested_freq reduction issue ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines PM / runtime: Use pm_runtime_put_sync() in __device_release_driver() ACPI / event: remove unneeded NULL pointer check Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1" ACPI / video: Quirk initial backlight level 0 ACPI / video: Fix initial level validity test intel_pstate: skip the driver if ACPI has power mgmt option PM / hibernate: Avoid overflow in hibernate_preallocate_memory() ACPI / hotplug: Do not execute "insert in progress" _OST ACPI / hotplug: Carry out PCI root eject directly ACPI / hotplug: Merge device hot-removal routines ACPI / hotplug: Make acpi_bus_hot_remove_device() internal ACPI / hotplug: Simplify device ejection routines ACPI / hotplug: Fix handle_root_bridge_removal() ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug ACPI / scan: Start matching drivers after trying scan handlers ACPI: Remove acpi_pci_slot_init() headers from internal.h ACPI / blacklist: fix name of ThinkPad Edge E530 PowerCap: Fix build error with option -Werror=format-security ... Conflicts: arch/arm/mach-omap2/opp.c drivers/Kconfig drivers/spi/spi.c
| * spi: attach/detach SPI device to the ACPI power domainMika Westerberg2013-10-111-2/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the SPI device is enumerated from ACPI namespace (it has an ACPI handle) it might have ACPI methods that needs to be called in order to transition the device to different power states (such as _PSx). We follow what has been done for platform and I2C buses here and attach the SPI device to the ACPI power domain if the device has an ACPI handle. This makes sure that the device is powered on when its ->probe() is called. For non-ACPI devices this patch is a no-op. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Mark Brown <broonie@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* | Merge remote-tracking branch 'spi/topic/loop' into spi-nextMark Brown2013-10-251-1/+129
|\ \
| * \ Merge remote-tracking branch 'spi/topic/s3c64xx' into spi-loopMark Brown2013-10-111-0/+35
| |\ \
| * | | spi: Provide common spi_message processing loopMark Brown2013-10-111-0/+92
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The loops which SPI controller drivers use to process the list of transfers in a spi_message are typically very similar and have some error prone areas such as the handling of /CS. Help simplify drivers by factoring this code out into the core - if drivers provide a transfer_one() function instead of a transfer_one_message() function the core will handle processing at the message level. /CS can be controlled by either setting cs_gpio or providing a set_cs function. If this is not possible for hardware reasons then both can be omitted and the driver should continue to implement manual /CS handling. This is a first step in refactoring and it is expected that there will be further enhancements, for example factoring out of the mapping of transfers for DMA and the initiation and completion of interrupt driven transfers. Signed-off-by: Mark Brown <broonie@linaro.org>
| * | | spi: Provide per-message prepare and unprepare operationsMark Brown2013-10-111-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many SPI drivers perform setup and tear down on every message, usually doing things like DMA mapping the message. Provide hooks for them to use to provide such operations. This is of limited value for drivers that implement transfer_one_message() but will be of much greater utility with future factoring out of standard implementations of that function. Signed-off-by: Mark Brown <broonie@linaro.org>
| * | | spi: Provide trace points for message processingMark Brown2013-10-071-1/+15
| | |/ | |/| | | | | | | | | | | | | | | | | | | Provide tracepoints for the lifecycle of a message from submission to completion and for the active time for masters to help with performance analysis of SPI I/O. Signed-off-by: Mark Brown <broonie@linaro.org>
* | | Merge remote-tracking branch 'spi/topic/core' into spi-nextMark Brown2013-10-251-41/+36
|\ \ \
| * | | spi: Fix checkpatch issueJingoo Han2013-10-141-7/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the following checkpatch error and warnings. ERROR: space required after that ',' (ctx:VxV) WARNING: quoted string split across lines WARNING: max() should probably be max_t(int, nb, master->num_chipselect) WARNING: sizeof *spi should be sizeof(*spi) WARNING: sizeof *master should be sizeof(*master) WARNING: sizeof x should be sizeof(x) Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Mark Brown <broonie@linaro.org>
| * | | spi: convert bus code to use dev_groupsGreg Kroah-Hartman2013-10-081-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The dev_attrs field of struct bus_type is going away soon, dev_groups should be used instead. This converts the spi bus code to use the correct field. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Mark Brown <broonie@linaro.org>
| * | | spi: Use of_property_read_u32Trent Piepho2013-09-271-26/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Instead of getting the raw property, checking the length, and doing endian conversion each time, use the OF function of_property_read_u32() that does all that. Error messages are slightly improved with error codes from of_property_read_u32() for different ways the property may be invalid (missing, too short, etc.) Signed-off-by: Trent Piepho <tpiepho@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-20 16:43:49 +0000