summaryrefslogtreecommitdiffstats
path: root/drivers/spi
Commit message (Collapse)AuthorAgeFilesLines
* [S390] Kconfig: menus with depends on HAS_IOMEM.Martin Schwidefsky2007-05-101-0/+1
| | | | | | | Add "depends on HAS_IOMEM" to a number of menus to make them disappear for s390 which does not have I/O memory. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* atmel_spi: remove unnecessary (and wrong) #ifdefsHaavard Skinnemoen2007-05-091-5/+0
| | | | | | | | | | | | | | Now that the cpu_is_xxx() macros are available both on AVR32 and AT91, we can remove a couple of #ifdefs from this driver. One of them is actually wrong -- new_1 should be set on AVR32 but isn't. This causes the bus clock to run at twice the speed it is configured to. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: David Brownell <david-b@pacbell.net> Acked-by: Andrew Victor <andrew@sanpeople.com> Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* au1550 SPI controller driverJan Nikitenko2007-05-083-0/+986
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Here is a driver for the Alchemy au1550 PSC (Programmable Serial Controller) in SPI master mode. It supports dma transfers using the Alchemy descriptor based dma controller for 4-8 bits per word SPI transfers. For 9-24 bits per word transfers, pio irq based mode is used to avoid setup of dma channels from scratch on each number of bits per word change. Tested with au1550; this may also work on other MIPS Alchemy cpus, like au1200/au1210/au1250. Used extensively with SD card connected via SPI; this handles 8.1MHz SPI clock transfers using dma without any problem (the highest SPI clock freq possible with au1550 running on 324MHz). The driver supports sharing of SPI bus by multiple devices. All features of Alchemy SPI mode are supported (all SPI modes, msb/lsb first, bits per word in 4-24 range). As the SPI clock of the controller depends on main input clock that shall be configured externally, platform data structure for au1550 SPI controller driver contains mainclk_hz attribute to define the input clock rate. From this value, dividers of the controller for SPI clock are set up for required frequency. Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com> Whitespace and section fixups. Remove partial workaround for platform setup bug in dma_mask setup; it couldn't work with multiple controllers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* SPI kerneldocDavid Brownell2007-05-081-5/+28
| | | | | | | | | | | | | | Various documentation updates for the SPI infrastructure, to clarify things that may not have been clear, to cope with lack of editing, and fix omissions. Also, plug SPI into the kernel-api DocBook template, and fix all the resulting glitches in document generation. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: "Randy.Dunlap" <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* /dev/spidevB.C interfaceAndrea Paterniani2007-05-083-0/+594
| | | | | | | | | | | | | | | | | | | | | | | | Add a filesystem API for <linux/spi/spi.h> stack. The initial version of this interface is purely synchronous. dbrownell@users.sourceforge.net: Cleaned up, bugfixed; much simplified; added preliminary documentation. Works with mdev given CONFIG_SYSFS_DEPRECATED; and presumably udev. Updated SPI_IOC_MESSAGE ioctl to full spi_message semantics, supporting groups of one or more transfers (each of which may be full duplex if desired). This is marked as EXPERIMENTAL with an explicit disclaimer that the API (notably the ioctls) is subject to change. Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* minor spi_butterfly cleanupDavid Brownell2007-05-081-58/+4
| | | | | | | | | | Simplify the spi_butterfly driver by removing incomplete/unused support for the second SPI bus, implemented by the USI controller. This should make this a clearer example of how to write a parport bitbang driver. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* layered parport code uses parport->devDavid Brownell2007-05-081-17/+4
| | | | | | | | | | | | | | | | | | | Update some of the layered parport_driver code to use parport->dev: - i2c-parport (parent of i2c_adapter) - spi_butterfly (parent of spi_master, allowing cruft removal) - lp (creating class_device) - ppdev (parent of parportN device) - tipar (creating class_device) There are still drivers that should be updated, like some of the input drivers; but they won't be any worse off than they are today. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Greg KH <greg@kroah.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi_s3c24xx.c: Fix buildArnaud Patard2007-05-071-2/+0
| | | | | | | | | | Commit a836f5856ae46ccb2464ea76031ea05ae967b832 removes the shutdown member of the bitbang structure, breaking the build of spi_s3c24xx.c. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Blackfin: blackfin on-chip SPI controller driverWu, Bryan2007-05-073-2/+1321
| | | | | | | | | | This patch implements the driver necessary use the Analog Devices Blackfin processor's SPI Port. Signed-off-by: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: fix use of set_cs in spi_s3c24xx driverBen Dooks2007-04-171-2/+2
| | | | | | | | | | | | | It turns out that the last patch to change set_cs to be kept in the controller's structure instead of the platform data was an incomplete change, and did not change the references to platfrom data in the setup xfer code. (This can prevent an oops.) Reported-by: <Ling.Alex@iac.com.tw> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] drivers/spi/: fix section mismatchesAdrian Bunk2007-03-271-6/+4
| | | | | | | | | | | WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_register_master from .text between 'spi_bitbang_start' (at offset 0x84e11a) and 'bitbang_work' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_alloc_master from .text between 'butterfly_attach' (at offset 0x84e681) and 'at25_remove' WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_new_device from .text between 'butterfly_attach' (at offset 0x84e7e4) and 'at25_remove' Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] spi_s3c24xx.c: warning fixArnaud Patard (Rtp2007-03-161-1/+1
| | | | | | | | | | | | | | | | | | | The set_cs field of struct s3c24xx_spi is declared as returning a int but the value returned but set_cs is never fixed. Moreover, the default function for set_cs and the set_cs defintion in the platform data are returning void. I'm proposing to change the prototype to void (*set_cs)(...). By doing this, I'm also fixing 2 build warnings: drivers/spi/spi_s3c24xx.c: In function 's3c24xx_spi_probe': drivers/spi/spi_s3c24xx.c:330: warning: assignment from incompatible pointer type drivers/spi/spi_s3c24xx.c:335: warning: assignment from incompatible pointer type Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] SPI: at25: do not use pointer before assignmentAtsushi Nemoto2007-03-161-1/+1
| | | | | | | | | | Prevents a potential oops with CONFIG_SPI_DEBUG given flakey hardware or incorrect configuration. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] gpio_direction_output() needs an initial valueDavid Brownell2007-03-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | It's been pointed out that output GPIOs should have an initial value, to avoid signal glitching ... among other things, it can be some time before a driver is ready. This patch corrects that oversight, fixing - documentation - platforms supporting the GPIO interface - users of that call (just one for now, others are pending) There's only one user of this call for now since most platforms are still using non-generic GPIO setup code, which in most cases already couples the initial value with its "set output mode" request. Note that most platforms are clear about the hardware letting the output value be set before the pin direction is changed, but the s3c241x docs are vague on that topic ... so those chips might not avoid the glitches. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Andrew Victor <andrew@sanpeople.com> Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] spi: destroy workqueue after spi_unregister_masterChris Lesiak2007-03-161-24/+2
| | | | | | | | | | | | | | | | | Fix a bug in the cleanup of an spi_bitbang bus. The workqueue associated with the bus was destroyed before the call to spi_unregister_master. That meant that spi devices on that bus would be unable to do IO in their remove method. The shutdown flag should have been able to prevent a segfault, but was never getting set. By waiting to destroy the workqueue until after the master is unregistered, devices are able to do IO in their remove methods. An added benefit is that neither the shutdown flag nor a wait for the queue of messages to empty is needed. Signed-off-by: Chris Lesiak <chris.lesiak@licor.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] spi_s3c2410_gpio.c spi mode 2 and 3 supportHarald Welte2007-02-201-0/+15
| | | | | | | | | | Add transfer modes 2 and 3 to the S3C24XX gpio SPI driver Signed-off-by: Harald Welte <laforge@openmoko.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] SPI controller build/warning fixesDavid Brownell2007-02-203-5/+8
| | | | | | | | | | | | The signature of the per-device cleanup() routine changed to remove its const-ness. Three new SPI controller drivers now need that change, to eliminate build warnings. This also fixes a build bug with atmel_spi on AT91 systems. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] SPI: atmel_spi driverHaavard Skinnemoen2007-02-144-0/+853
| | | | | | | | | | | | | | | | | | Driver for the Atmel on-chip SPI master controller. Tested primarily on AVR32/AT32AP7000/ATSTK1000 using mtd_dataflash and the jffs2 filesystem. Should also work fine on various AT91 ARM-based chips like AT91SAM926x and AT91RM9200. Hardware documentation can be found in the AT32AP7000 data sheet, or its AT91 siblings, which can be downloaded from http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] SPI eeprom driverDavid Brownell2007-02-123-0/+392
| | | | | | | | | | | | | | | | | This is adds a simple SPI EEPROM driver, providing access to the EEPROM through sysfs much like the I2C "eeprom" driver ... except this driver supports write access, and multiple EEPROM sizes. From: "Tuppa, Walter" <walter.tuppa@siemens.com> Since I have EEPROMs on SPI with different address sizing, I made some changes to your at25.c to support them. Works perfectly. (Also includes a small bugfix for the "what size address" test.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Walter Tuppa <walter.tuppa@siemens.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] SPI cleanup() method param becomes non-constHans-Peter Nilsson2007-02-123-4/+4
| | | | | | | | | | | | | | | | I'd like to assign NULL to kfree()d members of a structure. I can't do that without ugly casting (see the PXA patch) when the structure pointed to is const-qualified. I don't really see a reason why the cleanup method isn't allowed to alter the object it should clean up. :-) No, I didn't test the PXA patch, but I verified that the NULL-assignment doesn't stop me from doing rmmod/insmodding my own spi_bitbang-based driver. Signed-off-by: Hans-Peter Nilsson <hp@axis.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] spi_bitbang(): use overridable setup_transfer() methodHans-Peter Nilsson2007-02-121-4/+5
| | | | | | | | | | | | | | | | | | | A small bug-fix for spi_bitbang: it must always call the setup_transfer function via the overridable pointer, not assume that its spi_bitbang_setup_transfer is sufficient. Otherwise, if all options in the transfers are default (0), the overrided function will never be called. Granted, the function replacing it must call spi_bitbang_setup_transfer, but it might also have other important things to do, even if the second argument (the spi_transfer) is NULL. Tested together with the other patches on the spi_crisv32_sser and spi_crisv32_gpio drivers (not yet in the kernel, will IIUC be submitted as part of the usual arch-maintainer-pushes). Signed-off-by: Hans-Peter Nilsson <hp@axis.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] SPI: Freescale iMX SPI controller driver (BIS+)Andrea Paterniani2007-02-123-0/+1778
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the SPI controller driver for Freescale i.MX(S/L/1). Main features summary: > Per chip setup via board specific code and/or protocol driver. > Per transfer setup. > PIO transfers. > DMA transfers. > Managing of NULL tx / rx buffer for rd only / wr only transfers. This patch replace patch-2.6.20-rc4-spi_imx with the following changes: > Few cosmetic changes. > Function map_dma_buffers now return 0 for success and -1 for failure. > Solved a bug inside spi_imx_probe function (wrong error path). > Solved a bug inside setup function (bad undo setup for max_speed_hz). > For read-only transfers, always write zero bytes. This is almost the same as the 'BIS' version sent by Andrea, except for updating the 'DUMMY' byte so that read-only transfers shift out zeroes. That part of the API changed recently, since some half duplex peripheral chips require that semantic. Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] SPI controller driver for OMAP MicrowireDavid Brownell2007-02-123-0/+580
| | | | | | | | | | | | | | | | | | This adds a SPI driver for the Microwire controller on OMAP1 chips. This driver has been used in the Linux-OMAP tree for some time now, including with some of those displays using standardized 9-bit commands followed by data with 8-bit words. Microwire only supports half duplex transfers, but that's all that most SPI protocols need. When full duplex, or higher speeds, are needed there are several other controllers that can be used on OMAP. [akpm@osdl.org: cleanups] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Imre Deak <imre.deak@solidboot.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] SPI Kconfig fixDavid Brownell2007-02-121-7/+6
| | | | | | | | | Minor Kconfig cleanup ... put the SPI_S3C24XX entry in the correct location (alphabetical order). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Revert "Driver core: convert SPI code to use struct device"Greg Kroah-Hartman2007-02-074-22/+22
| | | | | | | | | This reverts commit 2943ecf2ed32632473c06f1975db47a7aa98c10f. This should go through the SPI maintainer, it was my fault that it did not. Especially as it conflicts with other patches he has pending. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Driver core: convert SPI code to use struct deviceGreg Kroah-Hartman2007-02-074-22/+22
| | | | | | | | | Converts from using struct "class_device" to "struct device" making everything show up properly in /sys/devices/ with symlinks from the /sys/class directory. Cc: <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] SPI: alternative fix for spi_busnum_to_masterAtsushi Nemoto2007-01-261-9/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a SPI master device exists, udev (udevtrigger) causes kernel crash, due to wrong kobj pointer in kobject_uevent_env(). This problem was not in 2.6.19. The backtrace (on MIPS) was: [<8024db6c>] kobject_uevent_env+0x54c/0x5e8 [<802a8264>] store_uevent+0x1c/0x3c (in drivers/class.c) [<801cb14c>] subsys_attr_store+0x2c/0x50 [<801cb80c>] flush_write_buffer+0x38/0x5c [<801cb900>] sysfs_write_file+0xd0/0x190 [<80181444>] vfs_write+0xc4/0x1a0 [<80181cdc>] sys_write+0x54/0xa0 [<8010dae4>] stack_done+0x20/0x3c flush_write_buffer() passes kobject of spi_master_class.subsys to subsys_addr_store(), then subsys_addr_store() passes a pointer to a struct subsystem to store_uevent() which expects a pointer to a struct class_device. The problem seems subsys_attr_store() called instead of class_device_attr_store(). This mismatch was caused by commit 3bd0f6943520e459659d10f3282285e43d3990f1, which overrides kset of master class. This made spi_master_class.subsys.kset.ktype NULL so subsys_sysfs_ops is used instead of class_dev_sysfs_ops. The commit was to fix spi_busnum_to_master(). Here is a patch fixes this function in other way, just searching children list of class_device. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] spi: fix error setting the spi mode in pxa2xx_spi.cJustin Clacherty2007-01-261-2/+3
| | | | | | | | | | | | | Currently the spi mode can be set to the wrong mode if you are switching from any mode other than mode 0. This is because the mode is set using a bitwise or on uncleared bits. The following patch clears the mode bits before setting the new mode. I've also modified it to use the appropriate defines from pxa-regs.h for readability. Signed-off-by: Justin Clacherty <justin@redfish-group.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] S3C24XX: fix passing spi chipselect to select routineBen Dooks2007-01-261-14/+14
| | | | | | | | | | | | | | | It turns out that the spi chipselect was not being passed to the set_cs routine if one was specified in the platform data. As part of the fix, change to using a set_cs field in the controller state, and put a default gpio routine in if the data passed does not specify it. Also remove the //#define DEBUG Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] spi_s3c24xx_gpio: use right headerArnaud Patard (Rtp2006-12-301-1/+1
| | | | | | | | | | | Russel King recently reminded us that one shouldn't use asm/arch/hardware.h but one should use asm/hardware.h. Unfortunately, the spi_s3c24xx_gpio driver is using the wrong header. This patch is fixing that. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] SPI: define null tx_buf to mean "shift out zeroes"David Brownell2006-12-302-1/+3
| | | | | | | | | | | | | | | | | | | | | | Some issues were recently turned up with the current specification of what it means for spi_transfer.tx_buf to be null, as part of transfers which are (from the SPI protocol driver perspective) pure reads. Specifically, that it seems better to change the TX behaviour there from "undefined" to "will shift zeroes". This lets protocol drivers (like the ads7846 driver) depend on that behavior. It's what most controller drivers in the tree are already doing (with one exception and one case of driver wanting-to-oops), it's what Microwire hardware will necessarily be doing, and it removes an issue whereby certain security audits would need to define such a value anyway as part of removing covert channels. This patch changes the specification to require shifting zeroes, and updates all currently merged SPI controller drivers to do so. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] fix s3c24xx gpio driver (include linux/workqueue.h)Ben Dooks2006-12-221-0/+1
| | | | | | | | | | The general gpio driver includes seem to now depend on having <linux/workqueue.h> included before they are. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] spi: stabilize PIO mode transfers on PXA2xx systemsStephen Street2006-12-101-293/+440
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Stabilize PIO mode transfers against a range of word sizes and FIFO thresholds and fixes word size setup/override issues. 1) 16 and 32 bit DMA/PIO transfers broken due to timing differences. 2) Potential for bad transfer counts due to transfer size assumptions. 3) Setup function broken is multiple ways. 4) Per transfer bit_per_word changes break DMA setup in pump_tranfers. 5) False positive timeout are not errors. 6) Changes in pxa2xx_spi_chip not effective in calls to setup. 7) Timeout scaling wrong for PXA255 NSSP. 8) Driver leaks memory while busy during unloading. Known issues: SPI_CS_HIGH and SPI_LSB_FIRST settings in struct spi_device are not handled. Testing: This patch has been test against the "random length, random bits/word, random data (verified on loopback) and stepped baud rate by octaves (3.6MHz to 115kHz)" test. It is robust in PIO mode, using any combination of tx and rx thresholds, and also in DMA mode (which internally computes the thresholds). Much thanks to Ned Forrester for exhaustive reviews, fixes and testing. The driver is substantially better for his efforts. Signed-off-by: Stephen Street <stephen@streetfiresound.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] spi: check platform_device_register_simple() errorAkinobu Mita2006-12-071-0/+2
| | | | | | | | | Check the return value of platform_device_register_simple(). Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] spi: set kset of master class dev explicitlyHans-Christian Egtvedt2006-12-071-0/+1
| | | | | | | | | | | | | <quote Imre Deak from Thu, 12 Jan 2006 21:18:54 +0200> In order for spi_busnum_to_master to work spi master devices must be linked into the spi_master_class.subsys.kset list. At the moment the default class_obj_subsys.kset is used and we can't enumerate the master devices. </quote> Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] spi: correct bus_num and buffer bug in spi coreHans-Christian Egtvedt2006-12-071-9/+7
| | | | | | | | | | | | | | Correct the following in driver/spi/spi.c in function spi_busnum_to_master: * must allow bus_num 0, the if is really not needed. * correct the name buffer which is too small for bus_num >= 10000. It should be 9 bytes big, not 8. Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] SPI: improve sysfs compiler complaint handlingJeff Garzik2006-12-071-1/+3
| | | | | | | Signed-off-by: Jeff Garzik <jeff@garzik.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] slab: remove SLAB_KERNELChristoph Lameter2006-12-072-3/+3
| | | | | | | | SLAB_KERNEL is an alias of GFP_KERNEL. Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* WorkQueue: Fix up arch-specific work items where possibleDavid Howells2006-12-051-4/+5
| | | | | | | | | | Fix up arch-specific work items where possible to use the new work_struct and delayed_work structs. Three places that enqueue bits of their stack and then return have been marked with #error as this is not permitted. Signed-Off-By: David Howells <dhowells@redhat.com>
* Merge branch 'master' of ↵David Howells2006-12-051-0/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: drivers/ata/libata-scsi.c include/linux/libata.h Futher merge of Linus's head and compilation fixups. Signed-Off-By: David Howells <dhowells@redhat.com>
| * [PATCH] severing fs.h, radix-tree.h -> sched.hAl Viro2006-12-041-0/+1
| | | | | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* | Merge branch 'master' of ↵David Howells2006-12-051-1/+1
|\| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: drivers/infiniband/core/iwcm.c drivers/net/chelsio/cxgb2.c drivers/net/wireless/bcm43xx/bcm43xx_main.c drivers/net/wireless/prism54/islpci_eth.c drivers/usb/core/hub.h drivers/usb/input/hid-core.c net/core/netpoll.c Fix up merge failures with Linus's head and fix new compilation failures. Signed-Off-By: David Howells <dhowells@redhat.com>
| * Fix misc Kconfig typosMatt LaPlante2006-11-301-1/+1
| | | | | | | | | | | | | | | | Fix various Kconfig typos. Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
* | WorkStruct: make allyesconfigDavid Howells2006-11-221-3/+4
|/ | | | | | Fix up for make allyesconfig. Signed-Off-By: David Howells <dhowells@redhat.com>
* [PATCH] spi section fixAndrew Morton2006-11-031-1/+0
| | | | | | | | | | WARNING: vmlinux - Section mismatch: reference to .init.text:spi_register_board_info from __ksymtab_gpl between '__ksymtab_spi_register_board_info' (at offset 0xc032f7d0) and '__ksymtab_spi_alloc_master' Fix this by removing the export. Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Various drivers' irq handlers: kill dead code, needless castsJeff Garzik2006-10-061-1/+1
| | | | | | | | | | | | | | | | - Eliminate casts to/from void* - Eliminate checks for conditions that never occur. These typically fall into two classes: 1) Checking for 'dev_id == NULL', then it is never called with NULL as an argument. 2) Checking for invalid irq number, when the only caller (the system) guarantees the irq handler is called with the proper 'irq' number argument. Signed-off-by: Jeff Garzik <jeff@garzik.org>
* IRQ: Maintain regs pointer globally rather than passing to IRQ handlersDavid Howells2006-10-053-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* Remove all inclusions of <linux/config.h>Dave Jones2006-10-042-2/+0
| | | | | | kbuild explicitly includes this at build time. Signed-off-by: Dave Jones <davej@redhat.com>
* [PATCH] lockdep: annotate on-stack completionsIngo Molnar2006-07-031-1/+1
| | | | | | | | | | | | lockdep needs to have the waitqueue lock initialized for on-stack waitqueues implicitly initialized by DECLARE_COMPLETION(). Annotate on-stack completions accordingly. Has no effect on non-lockdep kernels. Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Remove obsolete #include <linux/config.h>Jörn Engel2006-06-302-2/+0
| | | | | Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-24 02:55:11 +0000