summaryrefslogtreecommitdiffstats
path: root/drivers/spi
Commit message (Collapse)AuthorAgeFilesLines
* spi: fix spi_s3c24xx_gpio num_chipselectBen Dooks2008-12-011-0/+1
| | | | | | | | | | The spi master driver must have num_chipselect set to allow the bus to initialise. Pass this through the platform data. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: fix spi_s3c24xx_gpio device handle lookupBen Dooks2008-12-011-1/+1
| | | | | | | | | | | The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method to convert the spi device into the private data for the driver. Fix this by using spi_master_get_devdata. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: au1550_spi full duplex dma fixJan Nikitenko2008-12-011-10/+16
| | | | | | | | | | | Fix unsafe order in dma mapping operation: always flush data from the cache *BEFORE* invalidating it, to allow full duplex transfers where the same buffer may be used for both writes and reads. Tested with mmc-spi. Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: fix spi_imx probe oopsingJulien Boibessot2008-12-011-12/+13
| | | | | | | | | | | Corrects spi_imx driver oops during initialization/probing: can't use drv_data before it's allocated. Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: mpc52xx_psc_spi chipselect bugfixStefano Babic2008-12-011-1/+4
| | | | | | | | | | | | | | | | According to the manual the "tdfOnExit" flag must be set on the last byte we want to send. The PSC controller holds SS low until the flag is set. However, the flag was set always on the last byte of the FIFO, independently if it is the last byte of the transfer. This generates spurious toggling of the SS signals that breaks the protocol of some peripherals. Fix. Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: avoid spidev crash when device is removedWolfgang Ocker2008-12-011-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I saw a kernel oops in spidev_remove() when a spidev device was registered and I unloaded the SPI master driver: Unable to handle kernel paging request for data at address 0x00000004 Faulting instruction address: 0xc01c0c50 Oops: Kernel access of bad area, sig: 11 [#1] CDSPR Modules linked in: spi_ppc4xx(-) NIP: c01c0c50 LR: c01bf9e4 CTR: c01c0c34 REGS: cec89c30 TRAP: 0300 Not tainted (2.6.27.3izt) MSR: 00021000 <ME> CR: 24000228 XER: 20000007 DEAR: 00000004, ESR: 00800000 TASK = cf889040[2070] 'rmmod' THREAD: cec88000 GPR00: 00000000 cec89ce0 cf889040 cec8e000 00000004 cec8e000 ffffffff 00000000 GPR08: 0000001c c0336380 00000000 c01c0c34 00000001 1001a338 100e0000 100df49c GPR16: 100b54c0 100df49c 100ddd20 100f05a8 100b5340 100efd68 00000000 00000000 GPR24: 100ec008 100f0428 c0327788 c0327794 cec8e0ac cec8e000 c0336380 00000000 NIP [c01c0c50] spidev_remove+0x1c/0xe4 LR [c01bf9e4] spi_drv_remove+0x2c/0x3c Call Trace: [cec89d00] [c01bf9e4] spi_drv_remove+0x2c/0x3c [cec89d10] [c01859a0] __device_release_driver+0x78/0xb4 [cec89d20] [c0185ab0] device_release_driver+0x28/0x44 [cec89d40] [c0184be8] bus_remove_device+0xac/0xd8 [cec89d60] [c0183094] device_del+0x100/0x194 [cec89d80] [c0183140] device_unregister+0x18/0x30 [cec89da0] [c01bf30c] __unregister+0x20/0x34 [cec89db0] [c0182778] device_for_each_child+0x38/0x74 [cec89de0] [c01bf2d0] spi_unregister_master+0x28/0x44 [cec89e00] [c01bfeac] spi_bitbang_stop+0x1c/0x58 [cec89e20] [d908a5e0] spi_ppc4xx_of_remove+0x24/0x7c [spi_ppc4xx] [...] IMHO a call to spi_set_drvdata() is missing in spidev_probe(). The patch below helped. Signed-off-by: Wolfgang Ocker <weo@reccoware.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi_imx: full duplex dma corruption bugfixAndrea Paterniani2008-11-191-23/+22
| | | | | | | | | | | Fix unsafe order in dma mapping operation: always flush data from the cache *BEFORE* invalidating it, to allow full duplex transfers where the same buffer may be used for both writes and reads. Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pxa2xx_spi: bugfix full duplex dma data corruptionNed Forrester2008-11-191-12/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes a data corruption bug in pxa2xx_spi.c when operating in full duplex mode with DMA and using buffers that overlap. SPI transmit and receive buffers are allowed to be the same or to overlap. However, this driver fails if such overlap is attempted in DMA mode because it maps the rx and tx buffers in the wrong order. By mapping DMA_FROM_DEVICE (read) before DMA_TO_DEVICE (write), it invalidates the cache before flushing it, thus discarding data which should have been transmitted. The patch corrects the order of mapping. This bug exists in all versions of pxa2xx_spi.c; similar bugs are in the drivers for two other SPI controllers (au1500, imx). A version of this patch has been tested on kernel 2.6.20 using verification of loopback data with: random transfer length, random bits-per-word, random positive offsets (both larger and smaller than transfer length) between the start of the rx and tx buffers, and varying clock rates. Signed-off-by: Ned Forrester <nforrester@whoi.edu> Cc: Vernon Sauder <vernoninhand@gmail.com> Cc: J. Scott Merritt <merrij3@rpi.edu> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.27.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* atmel_spi: work-around required for new HW bug in AT91SAM9263 Rev.B SPI ↵Jean-Christophe Lallemand2008-11-121-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | controller We're working with an AT91SAM9263 Rev B in our design and I experienced some inconsistency in spi-based touchscreen usage between our board and the Atmel evaluation kit we have that runs on a Rev A chip. The data was apparently delayed by 1 byte and got ridiculous data out of the touchscreen driver, very strange. As everything looked normal in the spi, touchscreen and dma logs, I contacted the Atmel support and they triggered me on a new HW bug that appeared in the Rev B SPI controller. The problem is that the SPI controller on the Rev B needs that the software reset is performed two times so that it's performed correctly. Applying the patch below solves the issue on my Rev B board. I've tested it as well on my Rev A evaluation kit and it has apparently no unwanted side effect, things continue to work as expected. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6Linus Torvalds2008-10-161-4/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits) UIO: Fix mapping of logical and virtual memory UIO: add automata sercos3 pci card support UIO: Change driver name of uio_pdrv UIO: Add alignment warnings for uio-mem Driver core: add bus_sort_breadthfirst() function NET: convert the phy_device file to use bus_find_device_by_name kobject: Cleanup kobject_rename and !CONFIG_SYSFS kobject: Fix kobject_rename and !CONFIG_SYSFS sysfs: Make dir and name args to sysfs_notify() const platform: add new device registration helper sysfs: use ilookup5() instead of ilookup5_nowait() PNP: create device attributes via default device attributes Driver core: make bus_find_device_by_name() more robust usb: turn dev_warn+WARN_ON combos into dev_WARN debug: use dev_WARN() rather than WARN_ON() in device_pm_add() debug: Introduce a dev_WARN() function sysfs: fix deadlock device model: Do a quickcheck for driver binding before doing an expensive check Driver core: Fix cleanup in device_create_vargs(). Driver core: Clarify device cleanup. ...
| * device create: misc: convert device_create_drvdata to device_createGreg Kroah-Hartman2008-10-161-4/+3
| | | | | | | | | | | | | | | | Now that device_create() has been audited, rename things back to the original call to be sane. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds2008-10-162-6/+35
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (51 commits) [ARM] 5308/1: Fix Viper ISA IRQ handling [ARM] 5307/1: pxa: fix CM-X2XX PCMCIA build error [ARM] 5306/1: pxa: fix build error on CM-X270 [ARM] 5302/1: ARM: OMAP: Revert omap3 WDT changes to avoid merge conflict [ARM] 5305/1: ARM: OMAP: Fix compile of McBSP by removing unnecessary check [ARM] 5301/1: ARM: OMAP: Add missing irq defines ARM: OMAP3: Add default kernel config for OMAP LDP ARM: OMAP3: Add basic board support for OMAP LDP ARM: OMAP3: Defconfig for the Gumstix Overo board (rev 3) ARM: OMAP3: Add support for the Gumstix Overo board (rev 3) ARM: OMAP3: Add Beagle defconfig ARM: OMAP3: Add minimal Beagle board support ARM: OMAP3: Add minimal omap3430 support ARM: OMAP2: Fix sparse, checkpatch warnings in OMAP2/3 IRQ code ARM: OMAP: Fixes to omap_mcbsp_request function ARM: OMAP: Add support for OMAP2430 in McBSP ARM: OMAP: Add support for McBSP devices 3 - 5 on 34xx ARM: OMAP: Allocate McBSP devices dynamically Fix sections for omap-mcbsp platform driver [ARM] S3C24XX: Additional include moves ...
| * \ Merge branch 's3c-move' into develRussell King2008-10-142-3/+3
| |\ \ | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/mach-versatile/core.c
| * \ \ Merge branch 'omap-all' into develRussell King2008-10-142-6/+35
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/mach-omap2/gpmc.c arch/arm/mach-omap2/irq.c
| | * | | [ARM] omap: convert OMAP drivers to use ioremap()Russell King2008-09-052-5/+30
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | | [ARM] omap: remove an io_v2p() usageRussell King2008-09-051-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When omap_udc is also incorporated, this macro will no longer be used. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | | | | spi: core and gpio expanders use subsys_initDavid Brownell2008-10-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make the SPI external GPIO expander drivers register themselves at subsys_initcall() time when they're statically linked, and make the SPI core do its driver model initialization earlier so that's safe. SOC-integrated GPIOs are available starting very early -- often before initcalls start to run, or earily in arch_initcall() at latest -- so this improves consistency, letting more subsystems rely on GPIOs being usable by their own subsys_initcall() code. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | | orion_spi: handle 88F6183 erratumLennert Buytenhek2008-10-161-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support to orion_spi for the 88F6183 ARM SoC by adding code to work around a 6183-specific erratum. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | | pxa2xx_spi: fix chip_info defaults and documentation.Vernon Sauder2008-10-161-19/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make the chip info structure data optional by providing reasonable defaults. Improve corresponding documentation, and highlight the drawback of not providing explicit chipselect control. DMA can determine appropriate dma_burst_size and thresholds automatically so use DMA even if dma_burst_size is not specified. Signed-off-by: Vernon Sauder <VernonInHand@gmail.com> Reviewed-by: Ned Forrester <nforrester@whoi.edu> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | | pxa2xx_spi: minor cleanupGuennadi Liakhovetski2008-10-161-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Minor fixes: remove redundant local variable initialization, fix "can not" to what I _think_ is a preferred spelling, output IRQ number if requesting it failed. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | | spi_s3c24xx: pin configuration updatesBen Dooks2008-10-161-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a pin configuration callback for the s3c24xx SPI driver, as there are several options depending on the channel and the chip in use. This is needed as the controller may not have been setup by the initial bootloader and the fact that the SPI controller gets reset over suspend/resume into slave mode but the GPIO function registers do not. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | | spi: simplify spi_write_then_read()Vernon Sauder2008-10-161-14/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Modify spi_write_then_read() to use one transfer. This speeds up all callers, and is a minor code shrink. Signed-off-by: Vernon Sauder <Vernon.Sauder@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | | mpc52xx_psc_spi: remove code associated with !CONFIG_PPC_MERGEKumar Gala2008-10-161-55/+0
| |_|_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove the dead code associated with !CONFIG_PPC_MERGE. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: David Brownell <david-b@pacbell.net> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | Merge commit 'origin'Benjamin Herrenschmidt2008-10-154-39/+111
|\ \ \ \ | | |_|/ | |/| | | | | | | | | | | | | | Manual fixup of conflicts on: arch/powerpc/include/asm/dcr-regs.h drivers/net/ibm_newemac/core.h
| * | | orion_spi: fix handling of default transfer speedLennert Buytenhek2008-10-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Accept zero (the default!) as a per-transfer clock speed override. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * | | pxa2xx_spi: fix build breakageMike Rapoport2008-10-011-2/+2
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a build error in the pxa2xx-spi driver, introduced by commit 7e96445533ac3f4f7964646a202ff3620602fab4 ("pxa2xx_spi: dma bugfixes") CC drivers/spi/pxa2xx_spi.o drivers/spi/pxa2xx_spi.c: In function 'map_dma_buffers': drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary & drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary & drivers/spi/pxa2xx_spi.c: In function 'pump_transfers': drivers/spi/pxa2xx_spi.c:897: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int' [dbrownell@users.sourceforge.net: fix warning too ] Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * | spi_s3c24xx: fix section warningBen Dooks2008-09-131-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the section mismatch warning generated by the incorrect naming of s3c24xx_spidrv which should be s3c24xx_spi_driver: WARNING: drivers/spi/spi_s3c24xx.o(.data+0x4): Section mismatch in reference from the variable s3c24xx_spidrv to the (unknown reference) .exit.text:(unknown) Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * | pxa2xx_spi: dma bugfixesNed Forrester2008-09-131-14/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes two DMA bugs in the pxa2xx_spi driver. The first bug is in all versions of this driver; the second was introduced in the 2.6.20 kernel, and prevents using the driver with chips like m25p16 flash (which can issue large DMA reads). 1. Zero length transfers are permitted for use to insert timing, but pxa2xx_spi.c will fail if this is requested in DMA mode. Fixed by using programmed I/O (PIO) mode for such transfers. 2. Transfers larger than 8191 are not permitted in DMA mode. A test for length rejects all large transfers regardless of DMA or PIO mode. Worked around by rejecting only large transfers with DMA mapped buffers, and forcing all other transfers larger than 8191 to use PIO mode. A rate limited warning is issued for DMA transfers forced to PIO mode. This patch should apply to all kernels back to and including 2.6.20; it was test patched against 2.6.20. An additional patch would be required for older kernels, but those versions are very buggy anyway. Signed-off-by: Ned Forrester <nforrester@whoi.edu> Cc: Vernon Sauder <vernoninhand@gmail.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * | pxa2xx_spi: chipselect bugfixesNed Forrester2008-09-131-11/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes several chipselect bugs in the pxa2xx_spi driver. These bugs are in all versions of this driver and prevent using it with chips like m25p16 flash. 1. The spi_transfer.cs_change flag is handled too early: before spi_transfer.delay_usecs applies, thus making the delay ineffective at holding chip select. 2. spi_transfer.delay_usecs is ignored on the last transfer of a message (likewise not holding chipselect long enough). 3. If spi_transfer.cs_change is set on the last transfer, the chip select is always disabled, instead of the intended meaning: optionally holding chip select enabled for the next message. Those first three bugs were fixed with a relocation of delays and chip select de-assertions. 4. If a message has the cs_change flag set on the last transfer, and had the chip select stayed enabled as requested (see 3, above), it would not have been disabled if the next message is for a different chip. Fixed by dropping chip select regardless of cs_change at end of a message, if there is no next message or if the next message is for a different chip. This patch should apply to all kernels back to and including 2.6.20; it was test patched against 2.6.20. An additional patch would be required for older kernels, but those versions are very buggy anyway. Signed-off-by: Ned Forrester <nforrester@whoi.edu> Cc: Vernon Sauder <vernoninhand@gmail.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * | spi_mpc83xx: reject invalid transfer sizesPeter Korsgaard2008-09-131-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Error out on transfer length != multiple of bytes per word with -EINVAL. Fixes a buffer overrun crash if length < bytes per word. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * | spi_mpc83xx: fix clockrate calculation for low speedPeter Korsgaard2008-09-131-8/+5
| |/ | | | | | | | | | | | | | | | | | | | | | | | | Commit a61f5345 (spi_mpc83xx clockrate fixes) broke clockrate calculation for low speeds. SPMODE_DIV16 should be set if the divider is higher than 64, not only if the divider gets clipped to 1024. Furthermore, the clipping check was off by a factor 16 as well. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* / powerpc/mpc5200: fix build warnings on mpc52xx_psc_spi driverGrant Likely2008-10-081-3/+3
|/ | | | | | | | | | | | | The register definitions have been changed for the mpc5200 PSC ports to cover some of the changes in the mpc5200b. One change is that the ccr register is now a u32 instead of a u16. However, for the purposes of this driver we want to continue to use 16 bit access to avoid changing the existing (working) behaviour. This patch allows the driver to continue to do 16 bit accesses without the compiler complaining about it. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* spi: bugfix spi_add_device() with duplicate chipselectsDavid Brownell2008-08-151-11/+29
| | | | | | | | | | | | | | | | | | | | | | | When reviewing a recent patch I noticed a potential trouble spot in the registration of new SPI devices. The SPI master driver is told to set the device up before adding it to the driver model, so that it's always properly set up when probe() is called. (This is important, because in the case of inverted chipselects, this device can make the bus misbehave until it's properly deselected. It's got to be set up even if no driver binds to the device.) The trouble spot is that it doesn't first verify that no other device has been added using that chipselect. If such a device has been added, its configuration gets trashed. (Fortunately this has not been a common error!) The fix here adds an explicit check, and a mutex to protect the relevant critical region. [akpm@linux-foundation.org: make the lock local to spi_add_device()] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/machRussell King2008-08-077-22/+22
| | | | | | This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixesRussell King2008-08-077-74/+711
|\
| * spi: new orion_spi driverShadi Ammouri2008-08-053-0/+581
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds an SPI driver for the SPI controller found in various Marvell Orion ARM SoCs. It currently supports only one slave, which must use SPI mode 0. [dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"] Signed-off-by: Shadi Ammouri <shadi@marvell.com> Signed-off-by: Saeed Bishara <saeed@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * atmel_spi: fix hang due to missed interruptGerard Kam2008-08-041-5/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For some time my at91sam9260 board with JFFS2 on serial flash (m25p80) would hang when accessing the serial flash and SPI bus. Slowing the SPI clock down to 9 MHz reduced the occurrence of the hang from "always" during boot to a nuisance level that allowed other SW development to continue. Finally had to address this issue when an application stresses the I/O to always cause a hang. Hang seems to be caused by a missed SPI interrupt, so that the task ends up waiting forever after calling spi_sync(). The fix has 2 parts. First is to halt the DMA engine before the "current" PDC registers are loaded. This ensures that the "next" registers are loaded before the DMA operation takes off. The second part of the fix is a kludge that adds a "completion" interrupt in case the ENDRX interrupt for the last segment of the DMA chaining operation was missed. The patch allows the SPI clock for the serial flash to be increased from 9 MHz to 15 MHz (or more?). No hangs or SPI overruns were encountered. Haavard: while this patch does indeed improve things, I still see overruns and CRC errors on my NGW100 board when running the DataFlash at 10 MHz. However, I think some improvement is better than nothing, so I'm passing this on for inclusion in 2.6.27. Signed-off-by: Gerard Kam <gerardk5@verizon.net> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * spi: S3C24XX: reset register status on resume.Ben Dooks2008-08-041-10/+15
| | | | | | | | | | | | | | | | | | | | | | Fix a bug in the spi_s3c24xx driver where it does not reset the registers of the hardware when resuming from suspend (this block has been reset over suspend). Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * spi_s3c24xx: really assign busnumBen Dooks2008-07-281-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The original "Pass the bus number we expect the S3C24XX SPI driver to attach to via the platform data." [1] patch was mis-sent, and missed two important parts of the diff, which was to actually set the bus_num field and add the relevant field to the platform data. The previous commit 50f426b55d919dd017af35bb6a08753d1f262920 promised to add a bus_num field, but failed to include the two hunks that added this field to include/asm-arm/arch-s3c2410/spi.h and then pass it to the spi core when creating the new master field in drivers/spi/spi_s3c24xx.c. [1] git commit 50f426b55d919dd017af35bb6a08753d1f262920 Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * mpc52xx_psc_spi: fix block transferLuotao Fu2008-07-281-15/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The block transfer routine in the mpc52xx psc spi driver misinterpret the datasheet. According to the processor datasheet the chipselect is held as long as the EOF is not written. Theoretically blocks of any sizes can be transferred in this way. The old routine however writes an EOF after every word, which has the size of size_of_word. This makes the transfer slow. Also fixed some duplicate code. Signed-off-by: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * Merge commit 'gcl/gcl-next'Benjamin Herrenschmidt2008-07-281-44/+95
| |\
| | * spi: split up spi_new_device() to allow two stage registration.Grant Likely2008-07-251-44/+95
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | spi_new_device() allocates and registers an spi device all in one swoop. If the driver needs to add extra data to the spi_device before it is registered, then this causes problems. This is needed for OF device tree support so that the SPI device tree helper can add a pointer to the device node after the device is allocated, but before the device is registered. OF aware SPI devices can then retrieve data out of the device node to populate a platform data structure. This patch splits the allocation and registration portions of code out of spi_new_device() and creates two new functions; spi_alloc_device() and spi_register_device(). spi_new_device() is modified to use the new functions for allocation and registration. None of the existing users of spi_new_device() should be affected by this change. Drivers using the new API can forego the use of spi_board_info structure to describe the device layout and populate data into the spi_device structure directly. This change is in preparation for adding an OF device tree parser to generate spi_devices based on data in the device tree. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: David Brownell <dbrownell@users.sourceforge.net>
* | | [ARM] Remove asm/hardware.h, use asm/arch/hardware.h insteadRussell King2008-08-075-5/+3
|/ / | | | | | | | | | | | | | | | | Remove includes of asm/hardware.h in addition to asm/arch/hardware.h. Then, since asm/hardware.h only exists to include asm/arch/hardware.h, update everything to directly include asm/arch/hardware.h and remove asm/hardware.h. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* / dma-mapping: add the device argument to dma_mapping_error()FUJITA Tomonori2008-07-265-12/+12
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER architecture does: This enables us to cleanly fix the Calgary IOMMU issue that some devices are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423). I think that per-device dma_mapping_ops support would be also helpful for KVM people to support PCI passthrough but Andi thinks that this makes it difficult to support the PCI passthrough (see the above thread). So I CC'ed this to KVM camp. Comments are appreciated. A pointer to dma_mapping_ops to struct dev_archdata is added. If the pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's NULL, the system-wide dma_ops pointer is used as before. If it's useful for KVM people, I plan to implement a mechanism to register a hook called when a new pci (or dma capable) device is created (it works with hot plugging). It enables IOMMUs to set up an appropriate dma_mapping_ops per device. The major obstacle is that dma_mapping_error doesn't take a pointer to the device unlike other DMA operations. So x86 can't have dma_mapping_ops per device. Note all the POWER IOMMUs use the same dma_mapping_error function so this is not a problem for POWER but x86 IOMMUs use different dma_mapping_error functions. The first patch adds the device argument to dma_mapping_error. The patch is trivial but large since it touches lots of drivers and dma-mapping.h in all the architecture. This patch: dma_mapping_error() doesn't take a pointer to the device unlike other DMA operations. So we can't have dma_mapping_ops per device. Note that POWER already has dma_mapping_ops per device but all the POWER IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device argument. [akpm@linux-foundation.org: fix sge] [akpm@linux-foundation.org: fix svc_rdma] [akpm@linux-foundation.org: build fix] [akpm@linux-foundation.org: fix bnx2x] [akpm@linux-foundation.org: fix s2io] [akpm@linux-foundation.org: fix pasemi_mac] [akpm@linux-foundation.org: fix sdhci] [akpm@linux-foundation.org: build fix] [akpm@linux-foundation.org: fix sparc] [akpm@linux-foundation.org: fix ibmvscsi] Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Muli Ben-Yehuda <muli@il.ibm.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Avi Kivity <avi@qumranet.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: au1550_spi: improve pio transfer modeJan Nikitenko2008-07-241-20/+49
| | | | | | | | | | | | | | | | | | Improve PIO transfer mode of au1550 spi controller by continuing of spi transfer, instead of aborting transfer when transmit underflow interrupt occurrs. Verified by oscilloscope that the spi clock pauses on trasmit underflow, so transfer continuation is perfectly valid even though au1550 datasheet says that on tx underflow zeroes will be transfered. Also make some error messages more specific. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: au1550_spi: proper platform deviceManuel Lauss2008-07-241-64/+74
| | | | | | | | | | | | Remove the Au1550 resource table and instead extract MMIO/IRQ/DMA resources from platform resource information like any well-behaved platform driver. Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spidev: BKL removalAlan Cox2008-07-241-6/+13
| | | | | | | | | | Another step to removing ->ioctl and to removing the BKL [dbrownell@users.sourceforge.net: take final step; BKL not needed] Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* spi: make spi_board_info.modalias a char arrayGrant Likely2008-07-241-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, 'modalias' in the spi_device structure is a 'const char *'. The spi_new_device() function fills in the modalias value from a passed in spi_board_info data block. Since it is a pointer copy, the new spi_device remains dependent on the spi_board_info structure after the new spi_device is registered (no other fields in spi_device directly depend on the spi_board_info structure; all of the other data is copied). This causes a problem when dynamically propulating the list of attached SPI devices. For example, in arch/powerpc, the list of SPI devices can be populated from data in the device tree. With the current code, the device tree adapter must kmalloc() a new spi_board_info structure for each new SPI device it finds in the device tree, and there is no simple mechanism in place for keeping track of these allocations. This patch changes modalias from a 'const char *' to a fixed char array. By copying the modalias string instead of referencing it, the dependency on the spi_board_info structure is eliminated and an outside caller does not need to maintain a separate spi_board_info allocation for each device. If searched through the code to the best of my ability for any references to modalias which may be affected by this change and haven't found anything. It has been tested with the lite5200b platform in arch/powerpc. [dbrownell@users.sourceforge.net: cope with linux-next changes: KOBJ_NAME_LEN obliterated, etc] Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* SPI Kconfig simplificationsRobert P. J. Day2008-07-241-22/+23
| | | | | | | | | | Use "if SPI_MASTER" to remove numerous dependencies. [dbrownell@users.sourceforge.net: remove a couple now-needless EXPERIMENTAL dependencies too] Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* xilinx_spi: test below 0 on unsigned irq in xilinx_spi_probe()Roel Kluin2008-07-241-2/+3
| | | | | | | | | | | xilinx_spi->irq is unsigned, so the test fails Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Andrei Konovalov <akonovalov@ru.mvista.com> Cc: Yuri Frolov <yfrolov@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-18 21:02:54 +0000