summaryrefslogtreecommitdiffstats
path: root/drivers/spi
Commit message (Collapse)AuthorAgeFilesLines
*-------. Merge remote-tracking branches 'spi/fix/armada', 'spi/fix/atmel', ↵Mark Brown2017-12-195-4/+23
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | 'spi/fix/doc', 'spi/fix/imx', 'spi/fix/rspi', 'spi/fix/sun4i' and 'spi/fix/xilinx' into spi-linus
| | | | | * spi: xilinx: Detect stall with Unknown commandsRicardo Ribalda2017-11-241-0/+11
| |_|_|_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the core is configured in C_SPI_MODE > 0, it integrates a lookup table that automatically configures the core in dual or quad mode based on the command (first byte on the tx fifo). Unfortunately, that list mode_?_memoy_*.mif does not contain all the supported commands by the flash. Since 4.14 spi-nor automatically tries to probe the flash using SFDP (command 0x5a), and that command is not part of the list_mode table. Whit the right combination of C_SPI_MODE and C_SPI_MEMORY this leads into a stall that can only be recovered with a soft rest. This patch detects this kind of stall and returns -EIO to the caller on those commands. spi-nor can handle this error properly: m25p80 spi0.0: Detected stall. Check C_SPI_MODE and C_SPI_MEMORY. 0x21 0x2404 m25p80 spi0.0: SPI transfer failed: -5 spi_master spi0: failed to transfer one message from queue m25p80 spi0.0: s25sl064p (8192 Kbytes) Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
| | | | * spi: sun4i: disable clocks in the remove functionTakuo Koguchi2017-12-071-1/+1
| |_|_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mclk and hclk need to be disabled. Since pm_runtime_disable does not disable the clocks, use pm_runtime_force_suspend instead. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Takuo Koguchi <takuo.koguchi.sw@hitachi.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * spi: rspi: Do not set SPCR_SPE in qspi_set_config_register()Geert Uytterhoeven2017-12-071-2/+2
| |_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The R-Car Gen2 Hardware User Manual Rev. 2.00 states: If the master/slave mode select bit (MSTR) is modified while the SPI function enable bit (SPE) is set to 1 (that is, this module is enabled), the subsequent operation cannot be guaranteed. Hence do not set SPCR_SPE when setting SPCR_MSTR, just like the .set_config_register() implementations for other RSPI variants do. Note that when booted from QSPI, the boot loader will have set SPCR_MSTR already, hence usually the bit is never modified by the Linux driver. Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org>
| | * spi: atmel: fixed spin_lock usage inside atmel_spi_removeRadu Pirea2017-12-191-1/+1
| |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The only part of atmel_spi_remove which needs to be atomic is hardware reset. atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts enabled. atmel_spi_release_dma calls dma_release_channel and dma_release_channel locks a mutex inside of spin_lock. So the call of these functions can't be inside a spin_lock. Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Radu Pirea <radu.pirea@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * spi: a3700: Fix clk prescaling for coefficient over 15Maxime Chevallier2017-11-271-0/+8
|/ | | | | | | | | | | | | | | | The Armada 3700 SPI controller has 2 ranges of prescaler coefficients. One ranging from 0 to 15 by steps of 1, and one ranging from 0 to 30 by steps of 2. This commit fixes the prescaler coefficients that are over 15 so that it uses the correct range of values. The prescaling coefficient is rounded to the upper value if it is odd. This was tested on Espressobin with spidev and a locigal analyser. Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
*-----. Merge remote-tracking branches 'spi/topic/sh-msiof', 'spi/topic/slave', ↵Mark Brown2017-11-105-13/+433
|\ \ \ \ | | | | | | | | | | | | | | | 'spi/topic/spreadtrum' and 'spi/topic/tegra114' into spi-next
| | | | * spi: tegra114: correct register name in definitionRalf Ramsauer2017-10-091-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to "Tegra K1 Processor Technical Reference Manual" (p. 2448), bit 20 of SPI_COMMAND1 is called CS_SW_VAL and not CS_SS_VAL. Signed-off-by: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * | spi: sprd: Fix the possible negative value of BIT()Baolin Wang2017-10-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When enabling the ADI hardware channels, if the channel id is 31, then we will get one negative value -1 for BIT() macro, which will write incorrect value to register. Fixes: 7e2903cb91df ("spi: Add ADI driver for Spreadtrum platform") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * | spi: sprd-adi: fix platform_no_drv_owner.cocci warningsWu Fengguang2017-10-131-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | drivers/spi/spi-sprd-adi.c:409:3-8: No need to set .owner here. The core will do it. Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Fixes: 7e2903cb91df ("spi: Add ADI driver for Spreadtrum platform") Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * | spi: spreadtrum adi: add hwspinlock dependencyArnd Bergmann2017-10-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With CONFIG_HWSPINLOCK=m, the new driver fails to link as a built-in driver: drivers/spi/spi-sprd-adi.o: In function `sprd_adi_remove': spi-sprd-adi.c:(.text+0x18): undefined reference to `hwspin_lock_free' drivers/spi/spi-sprd-adi.o: In function `sprd_adi_probe': spi-sprd-adi.c:(.text+0xfc): undefined reference to `of_hwspin_lock_get_id' spi-sprd-adi.c:(.text+0x108): undefined reference to `hwspin_lock_request_specific' spi-sprd-adi.c:(.text+0x268): undefined reference to `hwspin_lock_free' This adds a hard Kconfig dependency on HWSPINLOCK for the !COMPILE_TEST case, and allows compile-testing with HWSPINLOCK completely disabled, which will then rely on the existing stub API. Fixes: 7e2903cb91df ("spi: Add ADI driver for Spreadtrum platform") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * | spi: sprd-adi: silence an uninitialized variable warningDan Carpenter2017-09-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If of_get_property() fails then "size" is uninitialized and it leads to a static checker warning: drivers/spi/spi-sprd-adi.c:288 sprd_adi_hw_init() error: uninitialized symbol 'size'. We can silence the warning by re-arranging the order of these checks. It obviously doesn't affect runtime at all. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * | spi: sprd-adi: checking for NULL instead of IS_ERR()Dan Carpenter2017-09-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | devm_ioremap_resource() returns error pointers, it never returns NULL. Fixes: 7e2903cb91df ("spi: Add ADI driver for Spreadtrum platform") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * | spi: Add ADI driver for Spreadtrum platformBaolin Wang2017-09-193-0/+426
| | | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ADI driver based on SPI framework for Spreadtrum SC9860 platform. Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| | * / spi: Kconfig: Remove old comments now that SPI slave is supportedFabio Estevam2017-09-201-4/+0
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 6c364062bfed ("spi: core: Add support for registering SPI slave controllers") SPI slave is also supported, so remove the old comments that say SPI slave is unsupported. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: sh-msiof: remove redundant pointer devColin Ian King2017-11-031-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The pointer dev is assigned but never read, hence it is redundant and can be removed. Cleans up clang warning: drivers/spi/spi-sh-msiof.c:1198:2: warning: Value stored to 'dev' is never read Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: sh-msiof: Use of_device_get_match_data() helperGeert Uytterhoeven2017-10-041-4/+2
| | | | | | | | | | | | | | | | | | | | | Use the of_device_get_match_data() helper instead of open coding. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: sh-msiof: Add compatible strings for r8a774[35]Fabrizio Castro2017-09-251-0/+2
| |/ | | | | | | | | Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| |
| \
| \
| \
| \
| \
| \
| \
*-------. \ Merge remote-tracking branches 'spi/topic/imx', 'spi/topic/mxs', ↵Mark Brown2017-11-105-60/+326
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | 'spi/topic/orion', 'spi/topic/rspi' and 'spi/topic/s3c64xx' into spi-next
| | | | | * | spi: s3c64xx: remove redundant pointer sciColin Ian King2017-11-031-3/+0
| | | | | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The pointer sci is assigned but never read, hence it is redundant and can be removed. Cleans up clang warning: drivers/spi/spi-s3c64xx.c:791:2: warning: Value stored to 'sci' is never read Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | | * / spi: rspi: Use of_device_get_match_data() helperGeert Uytterhoeven2017-10-041-4/+2
| | | | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the of_device_get_match_data() helper instead of open coding. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * / spi: orion: remove redundant assignment of status to zeroColin Ian King2017-11-021-1/+0
| | | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The assignment of status to zero is never read, status is either updated in the next iteration of the of the loop or several lines after the end of the loop. Remove it, cleans up clang warning: drivers/spi/spi-orion.c:674:4: warning: Value stored to 'status' is never read Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| | * / spi: mxs: implement runtime pmUwe Kleine-König2017-09-271-10/+110
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | This is a straight forward addition of runtime and system sleep pm operations that handle clk and pinctrl (for runtime pm) and spi_master_{suspend,resume} (for system sleep). Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: imx: Don't require platform data chipselect arrayTrent Piepho2017-11-101-7/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the array is not present, assume all chip selects are native. This is the standard behavior for SPI masters configured via the device tree and the behavior of this driver as well when it is configured via device tree. This reduces platform data vs DT differences and allows most of the platform data based boards to remove their chip select arrays. CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <kernel@pengutronix.de> CC: Fabio Estevam <fabio.estevam@nxp.com> CC: Mark Brown <broonie@kernel.org> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: imx: Fix failure path leak on GPIO request errorTrent Piepho2017-11-101-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the code that requests any chip select GPIOs fails, the cleanup of spi_bitbang_start() by calling spi_bitbang_stop() is not done. Add this to the failure path. Note that spi_bitbang_start() has to be called before requesting GPIOs because the GPIO data in the spi master is populated when the master is registed, and that doesn't happen until spi_bitbang_start() is called. CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <kernel@pengutronix.de> CC: Fabio Estevam <fabio.estevam@nxp.com> CC: Mark Brown <broonie@kernel.org> CC: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: imx: GPIO based chip selects should not be requiredTrent Piepho2017-11-101-8/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver will fail to load if no gpio chip selects are specified, this patch changes this so that it no longer fails. It's possible to use all native chip selects, in which case there is no reason to have a gpio chip select array. This is what happens if the *optional* device tree property "cs-gpios" is omitted. The spi core already checks for the absence of gpio chip selects in the master and assigns any slaves the gpio_cs value of -ENOENT. Also have the driver respect the standard SPI device tree property "num-cs" to allow setting the number of chip selects without using cs-gpios. CC: Mark Brown <broonie@kernel.org> CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <kernel@pengutronix.de> CC: Fabio Estevam <fabio.estevam@nxp.com> CC: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: imx: Fix failure path leak on GPIO request errorTrent Piepho2017-10-311-5/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the code that requests any chip select GPIOs fails, the cleanup of spi_bitbang_start() by calling spi_bitbang_stop() is not done. Fix this by moving spi_bitbang_start() to after the code that requets GPIOs. The GPIOs are dev managed and don't need explicit cleanup. Since spi_bitbang_start() is now the last operation, it doesn't need to be cleaned up in the failure path. CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <kernel@pengutronix.de> CC: Fabio Estevam <fabio.estevam@nxp.com> CC: Mark Brown <broonie@kernel.org> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: imx: Add support for SPI Slave modejiada wang2017-09-191-31/+196
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously i.MX SPI controller only works in Master mode. This patch adds support to i.MX51, i.MX53 and i.MX6 ECSPI controller to work also in Slave mode. Currently SPI Slave mode support patch has the following limitations: 1. The stale data in RXFIFO will be dropped when the Slave does any new transfer. 2. One transfer can be finished only after all transfer->len data been transferred to master device 3. Slave device only accepts transfer->len data. Any data longer than this from master device will be dropped. Any data shorter than this from master will cause SPI to stuck due to mentioned HW limitation 2. 4. Only PIO transfer is supported in Slave mode. 5. Dynamic burst size adjust isn't supported in Slave mode. Following HW limitation applies: 1. ECSPI has a HW issue when works in Slave mode, after 64 words written to TXFIFO, even TXFIFO becomes empty, ECSPI_TXDATA keeps shift out the last word data, so we have to disable ECSPI when in slave mode after the transfer completes 2. Due to Freescale errata ERR003775 "eCSPI: Burst completion by Chip Select (SS) signal in Slave mode is not functional" burst size must be set exactly to the size of the transfer. This limit SPI transaction with maximum 2^12 bits. This errata affects i.MX53 and i.MX6 ECSPI controllers. Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| |
| \
| \
| \
| \
| \
*-----. \ Merge remote-tracking branches 'spi/topic/armada', 'spi/topic/axi', ↵Mark Brown2017-11-104-36/+53
|\ \ \ \ \ | | | | |/ | | | |/| | | | | | 'spi/topic/davinci' and 'spi/topic/fsl-dspi' into spi-next
| | | | * spi: spi-fsl-dspi: enabling Coldfire mcf5441x dspiAngelo Dureghello2017-11-032-22/+46
| | | |/ | | | | | | | | | | | | | | | | Signed-off-by: Angelo Dureghello <angelo@sysam.it> Signed-off-by: Mark Brown <broonie@kernel.org>
| | * / spi: spi-axi: fix potential use-after-free after deregistrationJohan Hovold2017-10-311-1/+3
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Take an extra reference to the controller before deregistering it to prevent use-after-free in the interrupt handler in case an interrupt fires before the line is disabled. Fixes: b1353d1c1d45 ("spi: Add Analog Devices AXI SPI Engine controller support") Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: a3700: Change SPI mode before asserting chip-selectMaxime Chevallier2017-10-101-13/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The spi device mode should be configured in the controller before the chip-select is asserted, so that a clock polarity configuration change is not interpreted as a clock tick by the device. This patch moves the mode setting to the 'prepare_message' function instead of the 'transfer_one' function. By doing so, this patch also removes redundant code in a3700_spi_clock_set. This was tested on EspressoBin board, with spidev. Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | Merge remote-tracking branch 'spi/topic/core' into spi-nextMark Brown2017-11-101-1/+3
|\ \ \
| * | | spi: document odd controller reference handlingJohan Hovold2017-10-311-1/+3
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Document the fact that a reference to the controller is dropped as part of deregistration. This is an odd pattern as the reference is typically taken in __spi_alloc_controller() rather than spi_register_controller(). Most controller drivers gets it right these days and notably the device-managed interface relies on this behaviour. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
| | |
| \ \
*-. \ \ Merge remote-tracking branches 'spi/fix/idr' and 'spi/fix/sh-msiof' into ↵Mark Brown2017-11-102-3/+4
|\ \ \ \ | | | | | | | | | | | | | | | spi-linus
| | * | | spi: sh-msiof: Fix DMA transfer size checkHiromitsu Yamasaki2017-11-021-1/+1
| | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DMA supports 32-bit words only, even if BITLEN1 of SITMDR2 register is 16bit. Fixes: b0d0ce8b6b91 ("spi: sh-msiof: Add DMA support") Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | | spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbersLucas Stach2017-11-031-4/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On systems where some controllers get a dynamic ID assigned and some have a fixed number from DT, the current implemention might run into an IDR collision if the dynamic controllers gets probed first and get an IDR number, which is later requested by the controller with the fixed numbering. When this happens the fixed controller will fail to register with the SPI core. Fix this by skipping all known alias numbers when assigning the dynamic IDs. Fixes: 9b61e302210e (spi: Pick spi bus number from Linux idr or spi alias) Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | | spi: fix use-after-free at controller deregistrationJohan Hovold2017-10-311-2/+3
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The controller is typically freed as part of device_unregister() so store the bus id before deregistration to avoid use-after-free when the id is later released. Fixes: 9b61e302210e ("spi: Pick spi bus number from Linux idr or spi alias") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable <stable@vger.kernel.org>
* | | Merge tag 'spdx_identifiers-4.14-rc8' of ↵Linus Torvalds2017-11-025-0/+5
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull initial SPDX identifiers from Greg KH: "License cleanup: add SPDX license identifiers to some files Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>" * tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: License cleanup: add SPDX license identifier to uapi header files with a license License cleanup: add SPDX license identifier to uapi header files with no license License cleanup: add SPDX GPL-2.0 license identifier to files with no license
| * | | License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-025-0/+5
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| | |
| \ \
| \ \
| \ \
| \ \
| \ \
| \ \
| \ \
*-------. \ \ Merge remote-tracking branches 'spi/fix/armada', 'spi/fix/idr', ↵Mark Brown2017-10-254-107/+64
|\ \ \ \ \ \ \ | |_|_|_|_|/ / |/| | | | | / | | |_|_|_|/ | |/| | | | 'spi/fix/qspi', 'spi/fix/stm32' and 'spi/fix/uapi' into spi-linus
| | | | * | spi: stm32: Fix logical error in stm32_spi_prepare_mbr()Christos Gkekas2017-09-131-2/+2
| | | | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | stm32_spi_prepare_mbr() is returning an error value when div is less than SPI_MBR_DIV_MIN *and* greater than SPI_MBR_DIV_MAX, which always evaluates to false. This should change to use *or*. Signed-off-by: Christos Gkekas <chris.gekas@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| | | * / spi: bcm-qspi: Fix use after free in bcm_qspi_probe() in error pathFlorian Fainelli2017-10-121-4/+5
| |_|/ / |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There was an inversion in how the error path in bcm_qspi_probe() is done which would make us trip over a KASAN use-after-free report. Turns out that qspi->dev_ids does not get allocated until later in the probe process. Fix this by introducing a new lable: qspi_resource_err which takes care of cleaning up the SPI master instance. Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
| | * | spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbersLucas Stach2017-10-161-4/+9
| |/ / |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On systems where some controllers get a dynamic ID assigned and some have a fixed number from DT, the current implemention might run into an IDR collision if the dynamic controllers gets probed first and get an IDR number, which is later requested by the controller with the fixed numbering. When this happens the fixed controller will fail to register with the SPI core. Fix this by skipping all known alias numbers when assigning the dynamic IDs. Fixes: 9b61e302210e (spi: Pick spi bus number from Linux idr or spi alias) Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: a3700: Return correct value on timeout detectionMaxime Chevallier2017-10-101-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When waiting for transfer completion, a3700_spi_wait_completion returns a boolean indicating if a timeout occurred. The function was returning 'true' everytime, failing to detect any timeout. This patch makes it return 'false' when a timeout is reached. Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
| * | spi: armada-3700: Fix padding when sending not 4-byte aligned dataZachary Zhang2017-09-131-94/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In 4-byte transfer mode, extra padding/dummy bytes '0xff' would be sent in write operation if TX data is not 4-byte aligned since the SPI data register is always shifted out as whole 4 bytes. Fix this by using the header count feature that allows to transfer 0 to 4 bytes. Use it to actually send the first 1 to 3 bytes of data before the rest of the buffer that will hence be 4-byte aligned. Signed-off-by: Zachary Zhang <zhangzg@marvell.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * | spi: armada-3700: Fix failing commands with quad-SPIMiquel Raynal2017-09-131-2/+5
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A3700 SPI controller datasheet states that only the first line (IO0) is used to receive and send instructions, addresses and dummy bytes, unless for addresses during an RX operation in a quad SPI configuration (see p.821 of the Armada-3720-DB datasheet). Otherwise, some commands such as SPI NOR commands like READ_FROM_CACHE_DUAL_IO(0xeb) and READ_FROM_CACHE_DUAL_IO(0xbb) will fail because these commands must send address bytes through the four pins. Data transfer always use the four bytes with this setup. Thus, in quad SPI configuration, the A3700_SPI_ADDR_PIN bit must be set only in this case to inform the controller that it must use the number of pins indicated in the {A3700_SPI_DATA_PIN1,A3700_SPI_DATA_PIN0} field during the address cycles of an RX operation. Suggested-by: Ken Ma <make@marvell.com> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
* | Merge tag 'acpi-4.14-rc1' of ↵Linus Torvalds2017-09-051-0/+32
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI updates from Rafael Wysocki: "These include a usual ACPICA code update (this time to upstream revision 20170728), a fix for a boot crash on some systems with Thunderbolt devices connected at boot time, a rework of the handling of PCI bridges when setting up device wakeup, new support for Apple device properties, support for DMA configurations reported via ACPI on ARM64, APEI-related updates, ACPI EC driver updates and assorted minor modifications in several places. Specifics: - Update the ACPICA code in the kernel to upstream revision 20170728 including: * Alias operator handling update (Bob Moore). * Deferred resolution of reference package elements (Bob Moore). * Support for the _DMA method in walk resources (Bob Moore). * Tables handling update and support for deferred table verification (Lv Zheng). * Update of SMMU models for IORT (Robin Murphy). * Compiler and disassembler updates (Alex James, Erik Schmauss, Ganapatrao Kulkarni, James Morse). * Tools updates (Erik Schmauss, Lv Zheng). * Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv Zheng, Shao Ming). - Rework the initialization of non-wakeup GPEs with method handlers in order to address a boot crash on some systems with Thunderbolt devices connected at boot time where we miss an early hotplug event due to a delay in GPE enabling (Rafael Wysocki). - Rework the handling of PCI bridges when setting up ACPI-based device wakeup in order to avoid disabling wakeup for bridges prematurely (Rafael Wysocki). - Consolidate Apple DMI checks throughout the tree, add support for Apple device properties to the device properties framework and use these properties for the handling of I2C and SPI devices on Apple systems (Lukas Wunner). - Add support for _DMA to the ACPI-based device properties lookup code and make it possible to use the information from there to configure DMA regions on ARM64 systems (Lorenzo Pieralisi). - Fix several issues in the APEI code, add support for exporting the BERT error region over sysfs and update APEI MAINTAINERS entry with reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit Agrawal, Tony Luck, Yazen Ghannam). - Fix a potential initialization ordering issue in the ACPI EC driver and clean it up somewhat (Lv Zheng). - Update the ACPI SPCR driver to extend the existing XGENE 8250 workaround in it to a new platform (m400) and to work around an Xgene UART clock issue (Graeme Gregory). - Add a new utility function to the ACPI core to support using ACPI OEM ID / OEM Table ID / Revision for system identification in blacklisting or similar and switch over the existing code already using this information to this new interface (Toshi Kani). - Fix an xpower PMIC issue related to GPADC reads that always return 0 without extra pin manipulations (Hans de Goede). - Add statements to print debug messages in a couple of places in the ACPI core for easier diagnostics (Rafael Wysocki). - Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun Guo). - Clean up the ACPI x86 boot code somewhat (Andy Shevchenko). - Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver (Alex Hung). - Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal, Ronald Tschalär, Sumeet Pawnikar)" * tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits) ACPI / APEI: Suppress message if HEST not present intel_pstate: convert to use acpi_match_platform_list() ACPI / blacklist: add acpi_match_platform_list() ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources ACPI: make device_attribute const ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region ACPI: APEI: fix the wrong iteration of generic error status block ACPI / processor: make function acpi_processor_check_duplicates() static ACPI / EC: Clean up EC GPE mask flag ACPI: EC: Fix possible issues related to EC initialization order ACPI / PM: Add debug statements to acpi_pm_notify_handler() ACPI: Add debug statements to acpi_global_event_handler() ACPI / scan: Enable GPEs before scanning the namespace ACPICA: Make it possible to enable runtime GPEs earlier ACPICA: Dispatch active GPEs at init time ACPI: SPCR: work around clock issue on xgene UART ACPI: SPCR: extend XGENE 8250 workaround to m400 ACPI / LPSS: Don't abort ACPI scan on missing mem resource mailbox: pcc: Drop uninformative output during boot ACPI/IORT: Add IORT named component memory address limits ...
| * spi: Use Apple device properties in absence of ACPI resourcesLukas Wunner2017-08-031-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MacBooks and MacBook Pros introduced since 2015 return empty _CRS data for SPI slaves, causing device initialization to fail. Most of the information that would normally be conveyed via _CRS is available through ACPI device properties instead, so take advantage of them. The meaning and appropriate usage of the device properties was reverse engineered by Ronald Tschalär and carried over from these commits authored by him: https://github.com/cb22/macbook12-spi-driver/commit/9a416d699ef4 https://github.com/cb22/macbook12-spi-driver/commit/0c34936ed9a1 According to Ronald, the device properties have the following meaning: spiSclkPeriod /* period in ns */ spiWordSize /* in number of bits */ spiBitOrder /* 1 = MSB_FIRST, 0 = LSB_FIRST */ spiSPO /* clock polarity: 0 = low, 1 = high */ spiSPH /* clock phase: 0 = first, 1 = second */ spiCSDelay /* delay between cs and receive on reads in 10 us */ resetA2RUsec /* active-to-receive delay? */ resetRecUsec /* receive delay? */ Reported-by: Leif Liddy <leif.liddy@gmail.com> Tested-by: Ronald Tschalär <ronald@innovation.ch> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* | Merge remote-tracking branch 'spi/topic/xlp' into spi-nextMark Brown2017-09-041-2/+2
|\ \
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-12 22:05:46 +0000