summaryrefslogtreecommitdiffstats
path: root/include/linux/pci_regs.h
Commit message (Collapse)AuthorAgeFilesLines
* PCI: populate subsystem vendor and device IDs for PCI bridgesGabe Black2009-11-041-0/+5
| | | | | | | | | Change to populate the subsystem vendor and subsytem device IDs for PCI-PCI bridges that implement the PCI Subsystem Vendor ID capability. Previously bridges left subsystem vendor IDs unpopulated. Signed-off-by: Gabe Black <gabe.black@ni.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: acs p2p upsteram forwarding enablingAllen Kay2009-11-041-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Note: dom0 checking in v4 has been separated out into 2/2. This patch enables P2P upstream forwarding in ACS capable PCIe switches. It solves two potential problems in virtualization environment where a PCIe device is assigned to a guest domain using a HW iommu such as VT-d: 1) Unintentional failure caused by guest physical address programmed into the device's DMA that happens to match the memory address range of other downstream ports in the same PCIe switch. This causes the PCI transaction to go to the matching downstream port instead of go to the root complex to get translated by VT-d as it should be. 2) Malicious guest software intentionally attacks another downstream PCIe device by programming the DMA address into the assigned device that matches memory address range of the downstream PCIe port. We are in process of implementing device filtering software in KVM/XEN management software to allow device assignment of PCIe devices behind a PCIe switch only if it has ACS capability and with the P2P upstream forwarding bits enabled. This patch is intended to work for both KVM and Xen environments. Signed-off-by: Allen Kay <allen.m.kay@intel.com> Reviewed-by: Mathew Wilcox <willy@linux.intel.com> Reviewed-by: Chris Wright <chris@sous-sol.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* uio: add generic driver for PCI 2.3 devicesMichael S. Tsirkin2009-09-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | This adds a generic uio driver that can bind to any PCI device. First user will be virtualization where a qemu userspace process needs to give guest OS access to the device. Interrupts are handled using the Interrupt Disable bit in the PCI command register and Interrupt Status bit in the PCI status register. All devices compliant to PCI 2.3 (circa 2002) and all compliant PCI Express devices should support these bits. Driver detects this support, and won't bind to devices which do not support the Interrupt Disable Bit in the command register. It's expected that more features of interest to virtualization will be added to this driver in the future. Possibilities are: mmap for device resources, MSI/MSI-X, eventfd (to interface with kvm), iommu. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Chris Wright <chrisw@redhat.com> Signed-off-by: Hans J. Koch <hjk@linutronix.de> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Merge git://git.infradead.org/~dwmw2/iommu-2.6.31Linus Torvalds2009-06-221-0/+10
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.infradead.org/~dwmw2/iommu-2.6.31: intel-iommu: Fix one last ia64 build problem in Pass Through Support VT-d: support the device IOTLB VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps VT-d: add device IOTLB invalidation support VT-d: parse ATSR in DMA Remapping Reporting Structure PCI: handle Virtual Function ATS enabling PCI: support the ATS capability intel-iommu: dmar_set_interrupt return error value intel-iommu: Tidy up iommu->gcmd handling intel-iommu: Fix tiny theoretical race in write-buffer flush. intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing. intel-iommu: Clean up handling of "caching mode" vs. context flushing. VT-d: fix invalid domain id for KVM context flush Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support Intel IOMMU Pass Through Support Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
| * PCI: support the ATS capabilityYu Zhao2009-05-181-0/+10
| | | | | | | | | | | | | | | | | | | | | | The PCIe ATS capability makes the Endpoint be able to request the DMA address translation from the IOMMU and cache the translation in the device side, thus alleviate IOMMU pressure and improve the hardware performance in the I/O virtualization environment. Signed-off-by: Yu Zhao <yu.zhao@intel.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* | PCI MSI: Define PCI_MSI_MASK_32/64Hidetoshi Seto2009-06-111-1/+2
| | | | | | | | | | | | | | | | | | | | | | Impact: cleanup, improve readability Define PCI_MSI_MASK_32/64 for 32/64bit devices, instead of using implicit offset (-4), "PCI_MSI_MASK_BIT - 4" and "PCI_MSI_MASK_BIT". Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Reviewed-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* | PCI MSI: Remove unused/obsolete macros and definitionsHidetoshi Seto2009-06-111-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Impact: cleanup, spec compliance This patch does: - Remove unused msi/msix_enable/disable macros. User should use msi/msix_set_enable() functions instead. - Remove unused msix_mask/unmask/pending macros. These macros are useless because they are not based on any of the PCI Local Bus Specifications properly. It seems that they were written based on a draft of PCI spec, and that the draft was the MSI-X ECN that underwent membership review in September 2002. (* In the draft, the size of a entry in MSI-X table was 64bit, containing 32bit message data and DWORD aligned lower address plus a pending bit and a mask bit.(30+1+1bit) The higher address was placed in MSI-X capability structure and shared by all entries.) - Remove PCI_MSIX_FLAGS_BITMASK. This definition also come from the draft ECN. Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Reviewed-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* | PCI: only save/restore existent registers in the PCIe capabilityYu Zhao2009-04-221-0/+1
|/ | | | | | | | | | | | | | | PCIe 1.1 base neither requires the endpoint to implement the entire PCIe capability structure nor specifies default values of registers that are not implemented by the device. So we only save and restore registers that must be implemented by different device types if the device PCIe capability version is 1. PCIe 1.1 Capability Structure Expansion ECN and PCIe 2.0 requires all registers in the PCIe capability to be either implemented or hardwired to 0. Their PCIe capability version is 2. Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: save and restore PCIe 2.0 registersYu Zhao2009-03-261-0/+2
| | | | | | | | | PCIe 2.0 defines several new registers (Device Control 2, Link Control 2, and Slot Control 2). Save and retore them in pci_save_pcie_state() and pci_restore_pcie_state(). Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: initialize and release SR-IOV capabilityYu Zhao2009-03-201-0/+33
| | | | | | | | | | | | If a device has the SR-IOV capability, initialize it (set the ARI Capable Hierarchy in the lowest numbered PF if necessary; calculate the System Page Size for the VF MMIO, probe the VF Offset, Stride and BARs). A lock for the VF bus allocation is also initialized if a PF is the lowest numbered PF. Reviewed-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: fix incorrect mask of PM No_Soft_Reset bitYu Zhao2009-03-201-1/+1
| | | | | | Reviewed-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: pciehp: cleanup register and field definitionsKenji Kaneshige2009-01-071-7/+57
| | | | | | | | | | | | | Clean up register definitions related to PCI Express Hot plug. - Add register definitions into include/linux/pci_regs.h, and use them instead of pciehp's locally definied register definitions. - Remove pciehp's locally defined register definitions - Remove unused register definitions in pciehp. - Some minor cleanups. Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: add PCI Advanced Feature Capability definesSheng Yang2009-01-071-0/+12
| | | | | | | | | | PCI Advanced Features Capability is introduced by "Conventional PCI Advanced Caps ECN" (can be downloaded in pcisig.com). Add defines for the various AF capabilities, including function level reset (FLR). Reviewed-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Sheng Yang <sheng@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: add support for function level resetSheng Yang2008-10-221-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | Sometimes, it's necessary to enable software's ability to quiesce and reset endpoint hardware with function-level granularity, so provide support for it. The patch implement Function Level Reset(FLR) feature following PCI-e spec. And this is the first step. We would add more generic method, like D0/D3, to allow more devices support this function. The patch contains two functions. pcie_reset_function() is the new driver API, and, contains some action to quiesce a device. The other function is a helper: pcie_execute_reset_function() just executes the reset for a particular device function. Current the usage model is in KVM. Function reset is necessary for assigning device to a guest, or moving it between partitions. For Function Level Reset(FLR), please refer to PCI Express spec chapter 6.6.2. Signed-off-by: Sheng Yang <sheng@linux.intel.com> Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: support PCIe ARI capabilityYu Zhao2008-10-201-0/+14
| | | | | | | | | | | | This patch adds support for PCI Express Alternative Routing-ID Interpretation (ARI) capability. The ARI capability extends the Function Number field of the PCI Express Endpoint by reusing the Device Number which is otherwise hardwired to 0. With ARI, an Endpoint can have up to 256 functions. Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: disable ASPM on pre-1.1 PCIe devicesShaohua Li2008-07-281-0/+1
| | | | | | | | | Disable ASPM on pre-1.1 PCIe devices, as many of them don't implement it correctly. Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu> Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: Simplify PCI device PM codeRafael J. Wysocki2008-07-071-0/+1
| | | | | | | | | | If the offset of PCI device's PM capability in its configuration space, the mask of states that the device supports PME# from and the D1 and D2 support bits are cached in the corresponding struct pci_dev, the PCI device PM code can be simplified quite a bit. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* PCI: add PCI Express ASPM supportShaohua Li2008-04-201-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PCI Express ASPM defines a protocol for PCI Express components in the D0 state to reduce Link power by placing their Links into a low power state and instructing the other end of the Link to do likewise. This capability allows hardware-autonomous, dynamic Link power reduction beyond what is achievable by software-only controlled power management. However, The device should be configured by software appropriately. Enabling ASPM will save power, but will introduce device latency. This patch adds ASPM support in Linux. It introduces a global policy for ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control it. The interface can be used as a boot option too. Currently we have below setting: -default, BIOS default setting -powersave, highest power saving mode, enable all available ASPM state and clock power management -performance, highest performance, disable ASPM and clock power management By default, the 'default' policy is used currently. In my test, power difference between powersave mode and performance mode is about 1.3w in a system with 3 PCIE links. Note: some devices might not work well with aspm, either because chipset issue or device issue. The patch provide API (pci_disable_link_state), driver can disable ASPM for specific device. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Revert "PCI: PCIE ASPM support"Greg Kroah-Hartman2008-02-021-8/+0
| | | | | | | | | | | This reverts commit 6c723d5bd89f03fc3ef627d50f89ade054d2ee3b. It caused build errors on non-x86 platforms, config file confusion, and even some boot errors on some x86-64 boxes. All around, not quite ready for prime-time :( Cc: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* PCI: PCIE ASPM supportShaohua Li2008-02-011-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | PCI Express ASPM defines a protocol for PCI Express components in the D0 state to reduce Link power by placing their Links into a low power state and instructing the other end of the Link to do likewise. This capability allows hardware-autonomous, dynamic Link power reduction beyond what is achievable by software-only controlled power management. However, The device should be configured by software appropriately. Enabling ASPM will save power, but will introduce device latency. This patch adds ASPM support in Linux. It introduces a global policy for ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control it. The interface can be used as a boot option too. Currently we have below setting: -default, BIOS default setting -powersave, highest power saving mode, enable all available ASPM state and clock power management -performance, highest performance, disable ASPM and clock power management By default, the 'default' policy is used currently. In my test, power difference between powersave mode and performance mode is about 1.3w in a system with 3 PCIE links. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* PCI: modify PCI bridge control ISA flag for clarityGary Hade2007-10-121-1/+1
| | | | | | | | | | | | | | | | Modify PCI Bridge Control ISA flag for clarity This patch changes PCI_BRIDGE_CTL_NO_ISA to PCI_BRIDGE_CTL_ISA and modifies it's clarifying comment and locations where used. The change reduces the chance of future confusion since it makes the set/unset meaning of the bit the same in both the bridge control register and bridge_ctl field of the pci_bus struct. Signed-off-by: Gary Hade <garyhade@us.ibm.com> Acked-by: Linas Vepstas <linas@austin.ibm.com> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* PCI: Add missing PCI capability IDsAlex Chiang2007-10-121-1/+5
| | | | | | | | | | These IDs are in pciutils, but haven't been added to the kernel yet. Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [TG3]: Walk PCI capability lists.Matt Carlson2007-10-101-0/+13
| | | | | | | | | | | Newer tg3 devices shuffle around the registers in PCI configuration space. This patch changes the way the driver accesses the PCI capabilities registers. Hardcoded register locations are replaced with offsets from pci_find_capability() return values. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [PATCH] msi: Safer state caching.Eric W. Biederman2007-03-121-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two ways pci_save_state and pci_restore_state are used. As helper functions during suspend/resume, and as helper functions around a hardware reset event. When used as helper functions around a hardware reset event there is no reason to believe the calls will be paired, nor is there a good reason to believe that if we restore the msi state from before the reset that it will match the current msi state. Since arch code may change the msi message without going through the driver, drivers currently do not have enough information to even know when to call pci_save_state to ensure they will have msi state in sync with the other kernel irq reception data structures. It turns out the solution is straight forward, cache the state in the existing msi data structures (not the magic pci saved things) and have the msi code update the cached state each time we write to the hardware. This means we never need to read the hardware to figure out what the hardware state should be. By modifying the caching in this manner we get to remove our save_state routines and only need to provide restore_state routines. The only fields that were at all tricky to regenerate were the msi and msi-x control registers and the way we regenerate them currently is a bit dependent upon assumptions on how we use the allow msi registers to be configured and used making the code a little bit brittle. If we ever change what cases we allow or how we configure the msi bits we can address the fragility then. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [PATCH] msi: sanely support hardware level msi disablingEric W. Biederman2007-03-051-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | In some cases when we are not using msi we need a way to ensure that the hardware does not have an msi capability enabled. Currently the code has been calling disable_msi_mode to try and achieve that. However disable_msi_mode has several other side effects and is only available when msi support is compiled in so it isn't really appropriate. Instead this patch implements pci_msi_off which disables all msi and msix capabilities unconditionally with no additional side effects. pci_disable_device was redundantly clearing the bus master enable flag and clearing the msi enable bit. A device that is not allowed to perform bus mastering operations cannot generate intx or msi interrupt messages as those are essentially a special case of dma, and require bus mastering. So the call in pci_disable_device to disable msi capabilities was redundant. quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* PCI: Add #defines for Hypertransport MSI fieldsMichael Ellerman2006-12-201-0/+7
| | | | | | | | | Add a few #defines for grabbing and working with the address fields in a HT_CAPTYPE_MSI_MAPPING capability. All from the HT spec v3.00. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* PCI: Add pci_find_ht_capability() for finding Hypertransport capabilitiesMichael Ellerman2006-12-201-1/+11
| | | | | | | | | | | | | | | | | | There are already several places in the kernel that want to search a PCI device for a given Hypertransport capability. Although this is possible using pci_find_capability() etc., it makes sense to encapsulate that logic in a helper - pci_find_ht_capability(). To cater for searching exhaustively for a capability, we also provide pci_find_next_ht_capability(). We also need to cater for the fact that the HT capability fields may be either 3 or 5 bits wide. pci_find_ht_capability() deals with this for you, but callers using the #defines directly must handle that themselves. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* PCI: Make some MSI-X #defines genericMichael Ellerman2006-12-011-0/+6
| | | | | | | | | Move some MSI-X #defines into pci_regs.h so they can be used outside of drivers/pci. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [TG3]: Disable TSO on 5906 if CLKREQ is enabled.Michael Chan2006-11-151-0/+1
| | | | | | | | | | | Due to hardware errata, TSO must be disabled if the PCI Express clock request is enabled on 5906. The chip may hang when transmitting TSO frames if CLKREQ is enabled. Update version to 3.69. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [PATCH] Add Hypertransport capability definesEric W. Biederman2006-10-041-0/+21
| | | | | | | | | | | | This adds defines for the hypertransport capability subtypes and starts using them a little. [akpm@osdl.org: fix typo] Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* MSI: Rename PCI_CAP_ID_HT_IRQCONF into PCI_CAP_ID_HTBrice Goglin2006-09-261-1/+1
| | | | | | | | | | | | | 0x08 is the HT capability, while PCI_CAP_ID_HT_IRQCONF would be the subtype 0x80 that mpic_scan_ht_pic() uses. Rename PCI_CAP_ID_HT_IRQCONF into PCI_CAP_ID_HT. And by the way, use it in the ipath driver instead of defining its own HT_CAPABILITY_ID. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] PCI: add PCI Express AER register definitions to pci_regs.hZhang, Yanmin2006-07-121-0/+16
| | | | | | | | Add new defines of PCI-Express AER registers and their bits into file include/linux/pci_regs.h. Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] PCI: Add PCI_CAP_ID_VNDRBrice Goglin2006-06-221-0/+1
| | | | | | | | | | | | Add the vendor-specific extended capability PCI_CAP_ID_VNDR. It is required by the Myri-10G Ethernet driver. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Cc: Jeff Garzik <jeff@garzik.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] powerpc: Experimental support for new G5 Macs (#2)Benjamin Herrenschmidt2006-01-091-0/+1
| | | | | | | | | | | | | This adds some very basic support for the new machines, including the Quad G5 (tested), and other new dual core based machines and iMac G5 iSight (untested). This is still experimental ! There is no thermal control yet, there is no proper handing of MSIs, etc.. but it boots, I have all 4 cores up on my machine. Compared to the previous version of this patch, this one adds DART IOMMU support for the U4 chipset and thus should work fine on setups with more than 2Gb of RAM. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [PATCH] PCI: restore BAR values after D3hot->D0 for devices that need itJohn W. Linville2005-09-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration (including BARs) when transitioning from D3hot->D0. This leaves such a device in an inaccessible state. The patch below causes the BARs to be restored when enabling such a device, so that its driver will be able to access it. The patch also adds pci_restore_bars as a new global symbol, and adds a correpsonding EXPORT_SYMBOL_GPL for that. Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a (re)boot. Most drivers call pci_enable_device very early, so devices left in D3hot that lose configuration during the D3hot->D0 transition will be inaccessible to their drivers. Drivers could be modified to account for this, but it would be difficult to know which drivers need modification. This is especially true since often many devices are covered by the same driver. It likely would be necessary to replicate code across dozens of drivers. The patch below should trigger only when transitioning from D3hot->D0 (or at boot), and only for devices that have the "no soft reset" bit cleared in the PM control register. I believe it is safe to include this patch as part of the PCI infrastructure. The cleanest implementation of pci_restore_bars was to call pci_update_resource. Unfortunately, that does not currently exist for the sparc64 architecture. The patch below includes a null implemenation of pci_update_resource for sparc64. Some have expressed interest in making general use of the the pci_restore_bars function, so that has been exported to GPL licensed modules. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] PCI: clean up pci.h and split pci register info to separate header file.Greg Kroah-Hartman2005-09-081-0/+447
This cleans up some of the #ifdef CONFIG_PCI stuff up, and moves the pci register info out to a separate file, where it belongs. Eventually we can stop including this file from within pci.h, but lots of code needs to be audited first. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-23 01:30:15 +0000