summaryrefslogtreecommitdiffstats
path: root/include/linux/pinctrl
Commit message (Collapse)AuthorAgeFilesLines
* drivers/pinctrl: Add the concept of an "init" stateDouglas Anderson2015-10-272-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For pinctrl the "default" state is applied to pins before the driver's probe function is called. This is normally a sensible thing to do, but in some cases can cause problems. That's because the pins will change state before the driver is given a chance to program how those pins should behave. As an example you might have a regulator that is controlled by a PWM (output high = high voltage, output low = low voltage). The firmware might leave this pin as driven high. If we allow the driver core to reconfigure this pin as a PWM pin before the PWM's probe function runs then you might end up running at too low of a voltage while we probe. Let's introudce a new "init" state. If this is defined we'll set pinctrl to this state before probe and then "default" after probe (unless the driver explicitly changed states already). An alternative idea that was thought of was to use the pre-existing "sleep" or "idle" states and add a boolean property that we should start in that mode. This was not done because the "init" state is needed for correctness and those other states are only present (and only transitioned in to and out of) when (optional) power management is enabled. Changes in v3: - Moved declarations to pinctrl/devinfo.h - Fixed author/SoB Changes in v2: - Added comment to pinctrl_init_done() as per Linus W. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Caesar Wang <wxt@rock-chips.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: pinconf-generic: sort pin configuration params alphabeticallyMasahiro Yamada2015-10-021-32/+32
| | | | | | | | | | | | Currently, the dt_params array in drivers/pinctrl/pinconf-generic.c is not sorted in the same order as the enum pin_config_param in include/linux/pinctrl/pinconf-generic.h. Sort enum pin_config_param, conf_items, dt_params, alphabetically for consistency. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: use "const struct ..." rather than "struct ... const"Masahiro Yamada2015-06-011-1/+1
| | | | | | | | | | | Only this member, pins, is defined as "struct ... const *", but the others in this struct, pinlops, pmxops, confops, etc. are defined as "const struct ... *". Swap the "struct pinctrl_pin_desc" and "const" for consistency. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: remove useless const qualifierMasahiro Yamada2015-06-011-1/+1
| | | | | | | | | This "const" claims the get_function_groups callback never changes the given num_groups pointer. It is always true in C language, so not worth mentioning. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: use ERR_CAST instead of ERR_PTR/PTR_ERRFabian Frederick2015-05-061-1/+1
| | | | | | | Inspired by scripts/coccinelle/api/err_cast.cocci Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: move strict option to pinmux_opsLinus Walleij2015-05-062-3/+4
| | | | | | | | | | While the pinmux_ops are ideally just a vtable for pin mux calls, the "strict" setting belongs so intuitively with the pin multiplexing that we should move it here anyway. Putting it in the top pinctrl_desc makes no sense. Cc: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: allow exlusive GPIO/mux pin allocationSonic Zhang2015-05-061-0/+3
| | | | | | | | | | | | | | | | | | | | | Disallow simultaneous use of the the GPIO and peripheral mux functions by setting a flag "strict" in struct pinctrl_desc. The blackfin pinmux and gpio controller doesn't allow user to set up a pin for both GPIO and peripheral function. So, add flag strict in struct pinctrl_desc to check both gpio_owner and mux_owner before approving the pin request. v2-changes: - if strict flag is set, check gpio_owner and mux_onwer in if and else clause v3-changes: - add kerneldoc for this struct - augment Documentation/pinctrl.txt Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Revert "pinctrl: consumer: use correct retval for placeholder functions"Linus Walleij2015-03-051-3/+3
| | | | | | | | | | This reverts commit 5a7d2efdd93f6c4bb6cd3d5df3d2f5611c9b87ac. As per discussion on the mailing list, this is not the right thing to do. NULL cookies are valid in the stubs. Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: consumer: use correct retval for placeholder functionsWolfram Sang2015-01-141-3/+3
| | | | | | | These functions are supposed to return an error pointer, not NULL. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: pinconf-generic: loose DT dependenceLinus Walleij2015-01-142-8/+11
| | | | | | | | | | | | | New pin controllers such as ACPI-based may also have custom properties to parse, and should be able to use generic pin config. Let's make the code compile on !OF systems and rename members a bit to underscore it is custom parameters and not necessarily DT parameters. This fixes a build regression for x86_64 on the zeroday kernel builds. Reported-by: kbuild test robot <fengguang.wu@intel.com> Reviewed-and-tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: pinconf-generic: Allow driver to specify DT paramsSoren Brinkmann2015-01-112-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Additionally to the generic DT parameters, allow drivers to provide driver-specific DT parameters to be used with the generic parser infrastructure. To achieve this 'struct pinctrl_desc' is extended to pass custom pinconf option to the core. In order to pass this kind of information, the related data structures - 'struct pinconf_generic_dt_params', 'pin_config_item' - are moved from pinconf internals to the pinconf-generic header. Additionally pinconfg-generic is refactored to not only iterate over the generic pinconf parameters but also take the parameters into account that are provided through the driver's 'struct pinctrl_desc'. In particular 'pinconf_generic_parse_dt_config()' and 'pinconf_generic_dump' helpers are split into two parts each. In order to have a more generic helper that can be used to process the generic parameters as well as the driver-specific ones. v2: - fix typo - add missing documentation for @conf_items member in struct - rebase to pinctrl/devel: conflict in abx500 - rename _pinconf_generic_dump() to pinconf_generic_dump_one() - removed '_' from _parse_dt_cfg() - removed BUG_ONs, error condition is handled in if statements - removed pinconf_generic_dump_group() & pinconf_generic_dump_pin helpers - fixed up corresponding call sites - renamed pinconf_generic_dump() to pinconf_generic_dump_pins() - added kernel-doc to pinconf_generic_dump_pins() - add kernel-doc - more verbose commit message Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Tested-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: pinconf-generic: Infer map type from DT propertySoren Brinkmann2015-01-111-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | With the new 'groups' property, the DT parser can infer the map type from the fact whether 'pins' or 'groups' is used to specify the pin group to work on. To maintain backwards compatibitliy with current usage of the DT binding, this is only done when PIN_MAP_TYPE_INVALID is passed to the parsing function as type. Also, a new helper 'pinconf_generic_dt_node_to_map_all()' is introduced, which can be used by drivers as generic callback for dt_node_to_map() to leverage the new feature. Changes since v2: - rename dt_pin_specifier to subnode_target_type - add additional comment in header file explaining passing an invalid map type - mention map_all() helper in commit message Changes since RFC v2: - none Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Tested-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: generic: Fix PIN_CONFIG_DRIVE_OPEN_SOURCE source/drain doc mismatchGeert Uytterhoeven2014-09-041-1/+1
| | | | | | | PIN_CONFIG_DRIVE_OPEN_SOURCE enables open source, not open drain. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: clean up after enable refactoringLinus Walleij2014-09-041-4/+3
| | | | | | | | | | | | | | | | | commit 2243a87d90b42eb38bc281957df3e57c712b5e56 "pinctrl: avoid duplicated calling enable_pinmux_setting for a pin" removed the .disable callback from the struct pinmux_ops, making the .enable() callback the only remaining callback. However .enable() is a bad name as it seems to imply that a muxing can also be disabled. Rename the callback to .set_mux() and also take this opportunity to clean out any remaining mentions of .disable() from the documentation. Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Acked-by: Fan Wu <fwu@marvell.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: avoid duplicated calling enable_pinmux_setting for a pinFan Wu2014-07-111-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | What the patch does: 1. Call pinmux_disable_setting ahead of pinmux_enable_setting each time pinctrl_select_state is called 2. Remove the HW disable operation in pinmux_disable_setting function. 3. Remove the disable ops in struct pinmux_ops 4. Remove all the disable ops users in current code base. Notes: 1. Great thanks for the suggestion from Linus, Tony Lindgren and Stephen Warren and Everyone that shared comments on this patch. 2. The patch also includes comment fixes from Stephen Warren. The reason why we do this: 1. To avoid duplicated calling of the enable_setting operation without disabling operation inbetween which will let the pin descriptor desc->mux_usecount increase monotonously. 2. The HW pin disable operation is not useful for any of the existing platforms. And this can be used to avoid the HW glitch after using the item #1 modification. In the following case, the issue can be reproduced: 1. There is a driver that need to switch pin state dynamically, e.g. between "sleep" and "default" state 2. The pin setting configuration in a DTS node may be like this: component a { pinctrl-names = "default", "sleep"; pinctrl-0 = <&a_grp_setting &c_grp_setting>; pinctrl-1 = <&b_grp_setting &c_grp_setting>; } The "c_grp_setting" config node is totally identical, maybe like following one: c_grp_setting: c_grp_setting { pinctrl-single,pins = <GPIO48 AF6>; } 3. When switching the pin state in the following official pinctrl sequence: pin = pinctrl_get(); state = pinctrl_lookup_state(wanted_state); pinctrl_select_state(state); pinctrl_put(); Test Result: 1. The switch is completed as expected, that is: the device's pin configuration is changed according to the description in the "wanted_state" group setting 2. The "desc->mux_usecount" of the corresponding pins in "c_group" is increased without being decreased, because the "desc" is for each physical pin while the setting is for each setting node in the DTS. Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount will keep increasing without any chance to be decreased. According to the comments in the original code, only the setting, in old state but not in new state, will be "disabled" (calling pinmux_disable_setting), which is correct logic but not intact. We still need consider case that the setting is in both old state and new state. We can do this in the following two ways: 1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin setting" repeatedly 2. "Disable"(calling pinmux_disable_setting) the "same pin setting", actually two setting instances, ahead of enabling them. Analysis: 1. The solution #2 is better because it can avoid too much iteration. 2. If we disable all of the settings in the old state and one of the setting(s) exist in the new state, the pins mux function change may happen when some SoC vendors defined the "pinctrl-single,function-off" in their DTS file. old_setting => disabled_setting => new_setting. 3. In the pinmux framework, when a pin state is switched, the setting in the old state should be marked as "disabled". Conclusion: 1. To Remove the HW disabling operation to above the glitch mentioned above. 2. Handle the issue mentioned above by disabling all of the settings in old state and then enable the all of the settings in new state. Signed-off-by: Fan Wu <fwu@marvell.com> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: Add void * to pinctrl_pin_descSherman Yin2014-01-161-0/+2
| | | | | | | | | | drv_data is added to the pinctrl_pin_desc for drivers to define additional driver-specific per-pin data. Signed-off-by: Sherman Yin <syin@broadcom.com> Reviewed-by: Christian Daudt <bcm@fixthebug.org> Reviewed-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: Adds slew-rate, input-enable/disableSherman Yin2013-12-161-0/+4
| | | | | | | | This commit adds slew-rate and input-enable/disable support for pinconf -generic. Signed-off-by: Sherman Yin <syin@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: provide documentation pointerLinus Walleij2013-12-031-2/+4
| | | | | | | | | The PIN_CONFIG_OUTPUT parameter is really tricky to understand and needs an explicit pointer to the documentation. Cc: Tomasz Figa <t.figa@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl/gpio: non-linear GPIO ranges accesible from gpiolibChristian Ruppert2013-10-161-0/+3
| | | | | | | | This patch adds the infrastructure required to register non-linear gpio ranges through gpiolib and the standard GPIO device tree bindings. Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: Pass all configs to driver on pin_config_set()Sherman Yin2013-08-281-2/+4
| | | | | | | | | | | | | | | | | | | | | When setting pin configuration in the pinctrl framework, pin_config_set() or pin_config_group_set() is called in a loop to set one configuration at a time for the specified pin or group. This patch 1) removes the loop and 2) changes the API to pass the whole pin config array to the driver. It is now up to the driver to loop through the configs. This allows the driver to potentially combine configs and reduce the number of writes to pin config registers. All c files changed have been build-tested to verify the change compiles and that the corresponding .o is successfully generated. Signed-off-by: Sherman Yin <syin@broadcom.com> Reviewed-by: Christian Daudt <csd@broadcom.com> Reviewed-by: Matt Porter <matt.porter@linaro.org> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: utils : add support to pass config type in generic util APIsLaxman Dewangan2013-08-231-2/+20
| | | | | | | | | | | | | | | | | | | Add support to pass the config type like GROUP or PIN when using the utils or generic pin configuration APIs. This will make the APIs more generic. Added additional inline APIs such that it can be use directly as callback for the pinctrl_ops. Changes from V1: - Remove separate implementation for pins and group for pinctrl_utils_dt_free_map and improve this function to support both i.e. PINS and GROUPs. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: add includes and ifdefs for non-DT buildsLinus Walleij2013-08-151-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit e81c8f18afc4fdd6e34d8c83814b8b5134dbb30f "pinctrl: pinconf-generic: add generic APIs for mapping pinctrl node" Added function prototypes with implicit dependencies on other header files causing build warnings like this: In file included from arch/arm/mach-ux500/board-mop500-pins.c:12:0: include/linux/pinctrl/pinconf-generic.h:142:3: warning: 'struct device_node' declared inside parameter list [enabled by default] unsigned *reserved_maps, unsigned *num_maps); ^ include/linux/pinctrl/pinconf-generic.h:142:3: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default] include/linux/pinctrl/pinconf-generic.h:142:3: warning: 'struct pinctrl_dev' declared inside parameter list [enabled by default] include/linux/pinctrl/pinconf-generic.h:145:3: warning: 'struct device_node' declared inside parameter list [enabled by default] unsigned *num_maps); ^ Let's just add ifdefs for non-DT systems (the actual code is already ifdefed) and #include <linux/device.h> to get the most important structs and forward-declare the pinctrl core structs. Reported-by: Olof Johansson <olof@lixom.net> Cc: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: pinconf-generic: add generic APIs for mapping pinctrl nodeLaxman Dewangan2013-08-141-0/+6
| | | | | | | | | | | | | | | | | | | | Add generic APIs to map the DT node and its sub node in pinconf generic driver. These APIs can be used from driver to parse the DT node who uses the pinconf generic APIs for defining their nodes. Changes from V1: - Add generic property for pins and functions in pinconf-generic. - Add APIs to map the DT and subnode. - Move common utils APIs to the pinctrl-utils from this file. - Update the binding document accordingly. Changes from V2: - Rebased the pinctrl binding doc on top of Stephen's cleanup. - Rename properties "pinctrl-pins" and "pinctrl-function" to "pins" and "function". Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: set unit for debounce time pinconfig to usecHeiko Stübner2013-06-251-1/+1
| | | | | | | | | | | | Currently the debounce time pinconfig option uses an unspecified "time units" unit. As pinconfig options should use SI units and a real unit is also necessary for generic dt bindings, change it to usec. Currently no driver is using the generic pinconfig option for this, so the unit change is safe to do. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: more clarifications for generic pull configsHeiko Stübner2013-06-251-1/+4
| | | | | | | | | | | | | | PULL_PIN_DEFAULT is meant for hardware completely hiding any pull settings from the driver, so that it's really only possible to turn the pull on or off, but it not being possible to determine any pull settings from software. Also the binding-documentation for the pull arguments did not match the changes to the expected values. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: rip out the direct pinconf APILinus Walleij2013-06-251-43/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From the inception ot the pin config API there has been the possibility to get a handle at a pin directly and configure its electrical characteristics. For this reason we had: int pin_config_get(const char *dev_name, const char *name, unsigned long *config); int pin_config_set(const char *dev_name, const char *name, unsigned long config); int pin_config_group_get(const char *dev_name, const char *pin_group, unsigned long *config); int pin_config_group_set(const char *dev_name, const char *pin_group, unsigned long config); After the introduction of the pin control states that will control pins associated with devices, and its subsequent introduction to the device core, as well as the introduction of pin control hogs that can set up states on boot and optionally also at sleep, this direct pin control API is a thing of the past. As could be expected, it has zero in-kernel users. Let's delete this API and make our world simpler. Reported-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldocJames Hogan2013-06-181-1/+1
| | | | | | | | | | The kerneldoc comment for struct pinconf_ops was missing pin_config_dbg_parse_modify, and instead described pin_config_group_dbg_set (which is presumably an old name for the same function). Rename it in the kerneldoc comment so they match. Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: establish pull-up/pull-down terminologyLinus Walleij2013-06-171-6/+7
| | | | | | | | | | | | | | | It is counter-intuitive to have "0" mean disable in a boolean manner for electronic properties of pins such as pull-up and pull-down. Therefore, define that a pull-up/pull-down argument of 0 to such a generic option means that the pin is short-circuited to VDD or GROUND. Pull disablement shall be done using PIN_CONFIG_BIAS_DISABLE. Cc: James Hogan <james.hogan@imgtec.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by Heiko Stuebner <heiko@sntech.de> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Fix comment on pinctrl_gpio_range.pin_baseChristian Ruppert2013-06-171-1/+1
| | | | | | | | | The comment introduced with the recently added pinctrl_gpio_range.pins element was wrong. This corrects it. Thanks to Patrice Chotard for pointing this out. Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: move the pm state stubsLinus Walleij2013-06-171-15/+15
| | | | | | | | | The stubs for the !PINCTRL case were placed in the wrong part of the file, causing breakage in linux-next when compiling SH without pinctrl. Fix it up by moving the stubs to the right place. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: add pin list based GPIO rangesChristian Ruppert2013-06-171-1/+3
| | | | | | | | | Traditionally, GPIO ranges are based on consecutive ranges of both GPIO and pin numbers. This patch allows for GPIO ranges with arbitrary lists of pin numbers. Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* drivers: pinctrl sleep and idle states in the coreLinus Walleij2013-06-162-0/+38
| | | | | | | | | | | | | | | | | | | | | | | If a device have sleep and idle states in addition to the default state, look up these in the core and stash them in the pinctrl state container. Add accessor functions for pinctrl consumers to put the pins into "default", "sleep" and "idle" states passing nothing but the struct device * affected. Solution suggested by Kevin Hilman, Mark Brown and Dmitry Torokhov in response to a patch series from Hebbar Gururaja. Cc: Hebbar Gururaja <gururaja.hebbar@ti.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Mark Brown <broonie@kernel.org> Reviewed-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: add pinconf-generic define for a pin-default pullHeiko Stübner2013-06-161-0/+5
| | | | | | | | | | | | | | | There exist controllers that don't support to set the pull to up or down separately but instead automatically set the pull direction based on embedded knowledge inside the controller, for example depending on the selected mux function of the pin. Therefore this patch adds another config option to use this default pull-state for a pin where it is not possible to know or decide if the pin will be pulled up or down. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinconf-generic: add BIAS_BUS_HOLD pinconfJames Hogan2013-06-161-0/+6
| | | | | | | | | | | | Add a new PIN_CONFIG_BIAS_BUS_HOLD pin configuration for a bus holder pin mode (also known as bus keeper, or repeater). This is a weak latch which drives the last value on a tristate bus. Another device on the bus can drive the bus high or low before going tristate to change the value driven by the pin. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: generic: Fix typos and clarify commentsLaurent Pinchart2013-05-141-6/+6
| | | | | | | | Drive strength controls both sink and source currents, clarify the description accordingly. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl/pinconfig: add debug interfaceLaurent Meunier2013-04-191-0/+6
| | | | | | | | | | | | | | | | | | | | | | | This update adds a debugfs interface to modify a pin configuration for a given state in the pinctrl map. This allows to modify the configuration for a non-active state, typically sleep state. This configuration is not applied right away, but only when the state will be entered. This solution is mandated for us by HW validation: in order to test and verify several pin configurations during sleep without recompiling the software. Change log in this patch set; Take into account latest feedback from Stephen Warren: - stale comments update - improved code efficiency and readibility - limit size of global variable pinconf_dbg_conf - remove req_type as it can easily be added later when add/delete requests support is implemented Signed-off-by: Laurent Meunier <laurent.meunier@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: Declare operation structures as constLaurent Pinchart2013-03-071-3/+3
| | | | | | | | The pinconf, pinctrl and pinmux operation structures hold function pointers that are never modified. Declare them as const. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: generic: rename input schmitt disableHaojian Zhuang2013-02-151-2/+4
| | | | | | | | | Rename PIN_CONFIG_INPUT_SCHMITT_DISABLE to PIN_CONFIG_INPUT_SCHMITT_ENABLE. It's used to make it more generialize. Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* drivers/pinctrl: grab default handles from device coreLinus Walleij2013-01-231-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This makes the device core auto-grab the pinctrl handle and set the "default" (PINCTRL_STATE_DEFAULT) state for every device that is present in the device model right before probe. This will account for the lion's share of embedded silicon devcies. A modification of the semantics for pinctrl_get() is also done: previously if the pinctrl handle for a certain device was already taken, the pinctrl core would return an error. Now, since the core may have already default-grabbed the handle and set its state to "default", if the handle was already taken, this will be disregarded and the located, previously instanitated handle will be returned to the caller. This way all code in drivers explicitly requesting their pinctrl handlers will still be functional, and drivers that want to explicitly retrieve and switch their handles can still do that. But if the desired functionality is just boilerplate of this type in the probe() function: struct pinctrl *p; p = devm_pinctrl_get_select_default(&dev); if (IS_ERR(p)) { if (PTR_ERR(p) == -EPROBE_DEFER) return -EPROBE_DEFER; dev_warn(&dev, "no pinctrl handle\n"); } The discussion began with the addition of such boilerplate to the omap4 keypad driver: http://marc.info/?l=linux-input&m=135091157719300&w=2 A previous approach using notifiers was discussed: http://marc.info/?l=linux-kernel&m=135263661110528&w=2 This failed because it could not handle deferred probes. This patch alone does not solve the entire dilemma faced: whether code should be distributed into the drivers or if it should be centralized to e.g. a PM domain. But it solves the immediate issue of the addition of boilerplate to a lot of drivers that just want to grab the default state. As mentioned, they can later explicitly retrieve the handle and set different states, and this could as well be done by e.g. PM domains as it is only related to a certain struct device * pointer. ChangeLog v4->v5 (Stephen): - Simplified the devicecore grab code. - Deleted a piece of documentation recommending that pins be mapped to a device rather than hogged. ChangeLog v3->v4 (Linus): - Drop overzealous NULL checks. - Move kref initialization to pinctrl_create(). - Seeking Tested-by from Stephen Warren so we do not disturb the Tegra platform. - Seeking ACK on this from Greg (and others who like it) so I can merge it through the pinctrl subsystem. ChangeLog v2->v3 (Linus): - Abstain from using IS_ERR_OR_NULL() in the driver core, Russell recently sent a patch to remove it. Handle the NULL case explicitly even though it's a bogus case. - Make sure we handle probe deferral correctly in the device core file. devm_kfree() the container on error so we don't waste memory for devices without pinctrl handles. - Introduce reference counting into the pinctrl core using <linux/kref.h> so that we don't release pinctrl handles that have been obtained for two or more places. ChangeLog v1->v2 (Linus): - Only store a pointer in the device struct, and only allocate this if it's really used by the device. Cc: Felipe Balbi <balbi@ti.com> Cc: Benoit Cousson <b-cousson@ti.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Mitch Bradley <wmb@firmworks.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Rickard Andersson <rickard.andersson@stericsson.com> Cc: Russell King <linux@arm.linux.org.uk> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [swarren: fixed and simplified error-handling in pinctrl_bind_pins(), to correctly handle deferred probe. Removed admonition from docs not to use pinctrl hogs for devices] Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: generic: add slew rate config parameterHaojian Zhuang2013-01-211-0/+4
| | | | | | | Add PIN_CONFIG_SLEW_RATE parameter into pinconf-generic driver. Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: core: get devname from pinctrl_devHaojian Zhuang2013-01-211-0/+1
| | | | | | | | | Add new function to get devname from pinctrl_dev. pinctrl_dev_get_name() can only get pinctrl description name. If we want to use gpio driver to find pinctrl device node, we need to fetch the pinctrl device name. Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: pinconf-generic: add drive strength parameterMaxime Ripard2013-01-181-0/+3
| | | | | | | | | | Some pin configurations IP allows to set the current output to the pin. This patch adds such a parameter to the pinconf-generic mechanism. This parameter takes as argument the drive strength in mA. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: add pinconf-generic defines for outputLinus Walleij2013-01-111-0/+3
| | | | | | | | | | | | | | | This adds a definition of a generic output configuration for a certain pin when using the generic pin configuration library. Whereas driving pins low/high is usually a GPIO business, you may want to set up pins into a default state using hogs, and never touch them again. This helps out with that scenario. Based on a patch from Patrice Chotard. Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: generic: add input schmitt disable parameterHaojian Zhuang2012-11-211-2/+3
| | | | | | | | In Marvell PXA/MMP silicons, input schmitt disable value is 0x40, not 0. So append new config parameter -- input schmitt disable. Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pinctrl: add function to retrieve range from pinLinus Walleij2012-11-211-0/+3
| | | | | | | | | | | | | | This adds a function to the pinctrl core to retrieve the GPIO range associated with a certain pin for a certain controller. This is needed when a pinctrl driver want to look up the corresponding struct gpio_chip for a certain pin. As the GPIO drivers can now create these ranges themselves, the pinctrl driver no longer knows about all its associated GPIO chips. Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpiolib: rename find_pinctrl_*Linus Walleij2012-11-211-1/+1
| | | | | | | | | | Rename the function find_pinctrl_and_add_gpio_range() to pinctrl_find_and_add_gpio_range() so as to be consistent with the rest of the functions. Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpiolib: separation of pin concernsLinus Walleij2012-11-111-5/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The fact that of_gpiochip_add_pin_range() and gpiochip_add_pin_range() share too much code is fragile and will invariably mean that bugs need to be fixed in two places instead of one. So separate the concerns of gpiolib.c and gpiolib-of.c and have the latter call the former as back-end. This is necessary also when going forward with other device descriptions such as ACPI. This is done by: - Adding a return code to gpiochip_add_pin_range() so we can reliably check whether this succeeds. - Get rid of the custom of_pinctrl_add_gpio_range() from pinctrl. Instead create of_pinctrl_get() to just retrive the pin controller per se from an OF node. This composite function was just begging to be deleted, it was way to purpose-specific. - Use pinctrl_dev_get_name() to get the name of the retrieved pin controller and use that to call back into the generic gpiochip_add_pin_range(). Now the pin range is only allocated and tied to a pin controller from the core implementation in gpiolib.c. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gpiolib: provide provision to register pin rangesShiraz Hashim2012-11-111-0/+17
| | | | | | | | | | | | | | | | | | | | | | | pinctrl subsystem needs gpio chip base to prepare set of gpio pin ranges, which a given pinctrl driver can handle. This is important to handle pinctrl gpio request calls in order to program a given pin properly for gpio operation. As gpio base is allocated dynamically during gpiochip registration, presently there exists no clean way to pass this information to the pinctrl subsystem. After few discussions from [1], it was concluded that may be gpio controller reporting the pin range it supports, is a better way than pinctrl subsystem directly registering it. [1] http://comments.gmane.org/gmane.linux.ports.arm.kernel/184816 Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> [Edited documentation a bit] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Revert "pinctrl: remove pinctrl_remove_gpio_range"Viresh Kumar2012-11-111-0/+2
| | | | | | | | | | | | | | This reverts earlier commit which removed pinctrl_remove_gpio_range(), because at that time there weren't any more users of that routine. It was removed as the removal of ranges was done in unregister of pinctrl. But as we are now registering stuff from gpiolib, we may remove and insert a gpio module multiple times. So, we need this routine again. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Merge tag 'uapi-prep-20121002' of ↵Linus Torvalds2012-10-034-4/+4
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.infradead.org/users/dhowells/linux-headers Pull preparatory patches for user API disintegration from David Howells: "The patches herein prepare for the extraction of the Userspace API bits from the various header files named in the Kbuild files. New subdirectories are created under either include/uapi/ or arch/x/include/uapi/ that correspond to the subdirectory containing that file under include/ or arch/x/include/. The new subdirs under the uapi/ directory are populated with Kbuild files that mostly do nothing at this time. Further patches will disintegrate the headers in each original directory and fill in the Kbuild files as they do it. These patches also: (1) fix up #inclusions of "foo.h" rather than <foo.h>. (2) Remove some redundant #includes from the DRM code. (3) Make the kernel build infrastructure handle Kbuild files both in the old places and the new UAPI place that both specify headers to be exported. (4) Fix some kernel tools that #include kernel headers during their build. I have compile tested this with allyesconfig against x86_64, allmodconfig against i386 and a scattering of additional defconfigs of other arches. Prepared for main script Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Dave Jones <davej@redhat.com> Acked-by: H. Peter Anvin <hpa@zytor.com>" * tag 'uapi-prep-20121002' of git://git.infradead.org/users/dhowells/linux-headers: UAPI: Plumb the UAPI Kbuilds into the user header installation and checking UAPI: x86: Differentiate the generated UAPI and internal headers UAPI: Remove the objhdr-y export list UAPI: Move linux/version.h UAPI: Set up uapi/asm/Kbuild.asm UAPI: x86: Fix insn_sanity build failure after UAPI split UAPI: x86: Fix the test_get_len tool UAPI: (Scripted) Set up UAPI Kbuild files UAPI: Partition the header include path sets and add uapi/ header directories UAPI: (Scripted) Convert #include "..." to #include <path/...> in kernel system headers UAPI: (Scripted) Convert #include "..." to #include <path/...> in drivers/gpu/ UAPI: (Scripted) Remove redundant DRM UAPI header #inclusions from drivers/gpu/. UAPI: Refer to the DRM UAPI headers with <...> and from certain headers only
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-20 10:32:32 +0000