summaryrefslogtreecommitdiffstats
path: root/net/bridge/br_forward.c
Commit message (Collapse)AuthorAgeFilesLines
* net: bridge: add support for backup portNikolay Aleksandrov2018-07-231-1/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which allows to set a backup port to be used for known unicast traffic if the port has gone carrier down. The backup pointer is rcu protected and set only under RTNL, a counter is maintained so when deleting a port we know how many other ports reference it as a backup and we remove it from all. Also the pointer is in the first cache line which is hot at the time of the check and thus in the common case we only add one more test. The backup port will be used only for the non-flooding case since it's a part of the bridge and the flooded packets will be forwarded to it anyway. To remove the forwarding just send a 0/non-existing backup port. This is used to avoid numerous scalability problems when using MLAG most notably if we have thousands of fdbs one would need to change all of them on port carrier going down which takes too long and causes a storm of fdb notifications (and again when the port comes back up). In a Multi-chassis Link Aggregation setup usually hosts are connected to two different switches which act as a single logical switch. Those switches usually have a control and backup link between them called peerlink which might be used for communication in case a host loses connectivity to one of them. We need a fast way to failover in case a host port goes down and currently none of the solutions (like bond) cannot fulfill the requirements because the participating ports are actually the "master" devices and must have the same peerlink as their backup interface and at the same time all of them must participate in the bridge device. As Roopa noted it's normal practice in routing called fast re-route where a precalculated backup path is used when the main one is down. Another use case of this is with EVPN, having a single vxlan device which is backup of every port. Due to the nature of master devices it's not currently possible to use one device as a backup for many and still have all of them participate in the bridge (which is master itself). More detailed information about MLAG is available at the link below. https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG Further explanation and a diagram by Roopa: Two switches acting in a MLAG pair are connected by the peerlink interface which is a bridge port. the config on one of the switches looks like the below. The other switch also has a similar config. eth0 is connected to one port on the server. And the server is connected to both switches. br0 -- team0---eth0 | -- switch-peerlink Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add support for port isolationNikolay Aleksandrov2018-05-251-1/+2
| | | | | | | | | | | | | | | | This patch adds support for a new port flag - BR_ISOLATED. If it is set then isolated ports cannot communicate between each other, but they can still communicate with non-isolated ports. The same can be achieved via ACLs but they can't scale with large number of ports and also the complexity of the rules grows. This feature can be used to achieve isolated vlan functionality (similar to pvlan) as well, though currently it will be port-wide (for all vlans on the port). The new test in should_deliver uses data that is already cache hot and the new boolean is used to avoid an additional source port test in should_deliver. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: use hlist_entry_safeYueHaibing2018-04-271-2/+1
| | | | | | | | | Use hlist_entry_safe() instead of open-coding it. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd floodRoopa Prabhu2017-10-081-1/+1
| | | | | | | | | | | | | | | | | | | | | This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to suppress arp and nd flood on bridge ports. It implements rfc7432, section 10. https://tools.ietf.org/html/rfc7432#section-10 for ethernet VPN deployments. It is similar to the existing BR_PROXYARP* flags but has a few semantic differences to conform to EVPN standard. Unlike the existing flags, this new flag suppresses flood of all neigh discovery packets (arp and nd) to tunnel ports. Supports both vlan filtering and non-vlan filtering bridges. In case of EVPN, it is mainly used to avoid flooding of arp and nd packets to tunnel ports like vxlan. This patch adds netlink and sysfs support to set this bridge port flag. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: add per-port broadcast flood flagMike Manning2017-04-271-7/+17
| | | | | | | | | | | | | | | Support for l2 multicast flood control was added in commit b6cb5ac8331b ("net: bridge: add per-port multicast flood flag"). It allows broadcast as it was introduced specifically for unknown multicast flood control. But as broadcast is a special case of multicast, this may also need to be disabled. For this purpose, introduce a flag to disable the flooding of received l2 broadcasts. This approach is backwards compatible and provides flexibility in filtering for the desired packet types. Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Mike Manning <mmanning@brocade.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: allow IPv6 when multicast flood is disabledMike Manning2017-03-011-1/+2
| | | | | | | | | | | | Even with multicast flooding turned off, IPv6 ND should still work so that IPv6 connectivity is provided. Allow this by continuing to flood multicast traffic originated by us. Fixes: b6cb5ac8331b ("net: bridge: add per-port multicast flood flag") Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Mike Manning <mmanning@brocade.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: vlan dst_metadata hooks in ingress and egress pathsRoopa Prabhu2017-02-031-1/+1
| | | | | | | | | | | | | - ingress hook: - if port is a tunnel port, use tunnel info in attached dst_metadata to map it to a local vlan - egress hook: - if port is a tunnel port, use tunnel info attached to vlan to set dst_metadata on the skb CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: move maybe_deliver_addr() inside #ifdefArnd Bergmann2017-01-251-25/+25
| | | | | | | | | | | | | The only caller of this new function is inside of an #ifdef checking for CONFIG_BRIDGE_IGMP_SNOOPING, so we should move the implementation there too, in order to avoid this harmless warning: net/bridge/br_forward.c:177:13: error: 'maybe_deliver_addr' defined but not used [-Werror=unused-function] Fixes: 6db6f0eae605 ("bridge: multicast to unicast") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: multicast to unicastFelix Fietkau2017-01-241-2/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | Implements an optional, per bridge port flag and feature to deliver multicast packets to any host on the according port via unicast individually. This is done by copying the packet per host and changing the multicast destination MAC to a unicast one accordingly. multicast-to-unicast works on top of the multicast snooping feature of the bridge. Which means unicast copies are only delivered to hosts which are interested in it and signalized this via IGMP/MLD reports previously. This feature is intended for interface types which have a more reliable and/or efficient way to deliver unicast packets than broadcast ones (e.g. wifi). However, it should only be enabled on interfaces where no IGMPv2/MLDv1 report suppression takes place. This feature is disabled by default. The initial patch and idea is from Felix Fietkau. Signed-off-by: Felix Fietkau <nbd@nbd.name> [linus.luessing@c0d3.blue: various bug + style fixes, commit message] Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add per-port multicast flood flagNikolay Aleksandrov2016-09-011-0/+3
| | | | | | | | | Add a per-port flag to control the unknown multicast flood, similar to the unknown unicast flood flag and break a few long lines in the netlink flag exports. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: change unicast boolean to exact pkt_typeNikolay Aleksandrov2016-09-011-2/+2
| | | | | | | | | Remove the unicast flag and introduce an exact pkt_type. That would help us for the upcoming per-port multicast flood flag and also slightly reduce the tests in the input fast path. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: switchdev: Add forward mark support for stacked devicesIdo Schimmel2016-08-261-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of port netdevs so that packets being flooded by the device won't be flooded twice. It works by assigning a unique identifier (the ifindex of the first bridge port) to bridge ports sharing the same parent ID. This prevents packets from being flooded twice by the same switch, but will flood packets through bridge ports belonging to a different switch. This method is problematic when stacked devices are taken into account, such as VLANs. In such cases, a physical port netdev can have upper devices being members in two different bridges, thus requiring two different 'offload_fwd_mark's to be configured on the port netdev, which is impossible. The main problem is that packet and netdev marking is performed at the physical netdev level, whereas flooding occurs between bridge ports, which are not necessarily port netdevs. Instead, packet and netdev marking should really be done in the bridge driver with the switch driver only telling it which packets it already forwarded. The bridge driver will mark such packets using the mark assigned to the ingress bridge port and will prevent the packet from being forwarded through any bridge port sharing the same mark (i.e. having the same parent ID). Remove the current switchdev 'offload_fwd_mark' implementation and instead implement the proposed method. In addition, make rocker - the sole user of the mark - use the proposed method. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: remove _deliver functions and consolidate forward codeNikolay Aleksandrov2016-07-161-119/+65
| | | | | | | | | | | | | | | Before this patch we had two flavors of most forwarding functions - _forward and _deliver, the difference being that the latter are used when the packets are locally originated. Instead of all this function pointer passing and code duplication, we can just pass a boolean noting that the packet was locally originated and use that to perform the necessary checks in __br_forward. This gives a minor performance improvement but more importantly consolidates the forwarding paths. Also add a kernel doc comment to explain the exported br_forward()'s arguments. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: drop skb2/skb0 variables and use a local_rcv booleanNikolay Aleksandrov2016-07-161-17/+18
| | | | | | | | | | | Currently if the packet is going to be received locally we set skb0 or sometimes called skb2 variables to the original skb. This can get confusing and also we can avoid one conditional on the fast path by simply using a boolean and passing it around. Thanks to Roopa for the name suggestion. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: extend MLD/IGMP query statsNikolay Aleksandrov2016-07-091-5/+2
| | | | | | | | | | | | | | | | | | | As was suggested this patch adds support for the different versions of MLD and IGMP query types. Since the user visible structure is still in net-next we can augment it instead of adding netlink attributes. The distinction between the different IGMP/MLD query types is done as suggested in Section 7.1, RFC 3376 [1] and Section 8.1, RFC 3810 [2] based on query payload size and code for IGMP. Since all IGMP packets go through multicast_rcv() and it uses ip_mc_check_igmp/ipv6_mc_check_mld we can be sure that at least the ip/ipv6 header can be directly used. [1] https://tools.ietf.org/html/rfc3376#section-7 [2] https://tools.ietf.org/html/rfc3810#section-8.1 Suggested-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add support for IGMP/MLD stats and export them via netlinkNikolay Aleksandrov2016-06-301-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds stats support for the currently used IGMP/MLD types by the bridge. The stats are per-port (plus one stat per-bridge) and per-direction (RX/TX). The stats are exported via netlink via the new linkxstats API (RTM_GETSTATS). In order to minimize the performance impact, a new option is used to enable/disable the stats - multicast_stats_enabled, similar to the recent vlan stats. Also in order to avoid multiple IGMP/MLD type lookups and checks, we make use of the current "igmp" member of the bridge private skb->cb region to record the type on Rx (both host-generated and external packets pass by multicast_rcv()). We can do that since the igmp member was used as a boolean and all the valid IGMP/MLD types are positive values. The normal bridge fast-path is not affected at all, the only affected paths are the flooding ones and since we make use of the IGMP/MLD type, we can quickly determine if the packet should be counted using cache-hot data (cb's igmp member). We add counters for: * IGMP Queries * IGMP Leaves * IGMP v1/v2/v3 reports * MLD Queries * MLD Leaves * MLD v1/v2 reports These are invaluable when monitoring or debugging complex multicast setups with bridges. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: remove skb_sender_cpu_clear()WANG Cong2016-03-011-1/+0
| | | | | | | | | After commit 52bd2d62ce67 ("net: better skb->sender_cpu and skb->napi_id cohabitation") skb_sender_cpu_clear() becomes empty and can be removed. Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: set is_local and is_static before fdb entry is added to the fdb ↵Roopa Prabhu2015-10-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | hashtable Problem Description: We can add fdbs pointing to the bridge with NULL ->dst but that has a few race conditions because br_fdb_insert() is used which first creates the fdb and then, after the fdb has been published/linked, sets "is_local" to 1 and in that time frame if a packet arrives for that fdb it may see it as non-local and either do a NULL ptr dereference in br_forward() or attach the fdb to the port where it arrived, and later br_fdb_insert() will make it local thus getting a wrong fdb entry. Call chain br_handle_frame_finish() -> br_forward(): But in br_handle_frame_finish() in order to call br_forward() the dst should not be local i.e. skb != NULL, whenever the dst is found to be local skb is set to NULL so we can't forward it, and here comes the problem since it's running only with RCU when forwarding packets it can see the entry before "is_local" is set to 1 and actually try to dereference NULL. The main issue is that if someone sends a packet to the switch while it's adding the entry which points to the bridge device, it may dereference NULL ptr. This is needed now after we can add fdbs pointing to the bridge. This poses a problem for br_fdb_update() as well, while someone's adding a bridge fdb, but before it has is_local == 1, it might get moved to a port if it comes as a source mac and then it may get its "is_local" set to 1 This patch changes fdb_create to take is_local and is_static as arguments to set these values in the fdb entry before it is added to the hash. Also adds null check for port in br_forward. Fixes: 3741873b4f73 ("bridge: allow adding of fdb entries pointing to the bridge device") Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: vlan: use proper rcu for the vlgrp memberNikolay Aleksandrov2015-10-131-3/+3
| | | | | | | | | | | | | The bridge and port's vlgrp member is already used in RCU way, currently we rely on the fact that it cannot disappear while the port exists but that is error-prone and we might miss places with improper locking (either RCU or RTNL must be held to walk the vlan_list). So make it official and use RCU for vlgrp to catch offenders. Introduce proper vlgrp accessors and use them consistently throughout the code. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: vlan: add per-vlan struct and move to rhashtablesNikolay Aleksandrov2015-09-291-4/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch changes the bridge vlan implementation to use rhashtables instead of bitmaps. The main motivation behind this change is that we need extensible per-vlan structures (both per-port and global) so more advanced features can be introduced and the vlan support can be extended. I've tried to break this up but the moment net_port_vlans is changed and the whole API goes away, thus this is a larger patch. A few short goals of this patch are: - Extensible per-vlan structs stored in rhashtables and a sorted list - Keep user-visible behaviour (compressed vlans etc) - Keep fastpath ingress/egress logic the same (optimizations to come later) Here's a brief list of some of the new features we'd like to introduce: - per-vlan counters - vlan ingress/egress mapping - per-vlan igmp configuration - vlan priorities - avoid fdb entries replication (e.g. local fdb scaling issues) The structure is kept single for both global and per-port entries so to avoid code duplication where possible and also because we'll soon introduce "port0 / aka bridge as port" which should simplify things further (thanks to Vlad for the suggestion!). Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port rhashtable, if an entry is added to a port it'll get a pointer to its global context so it can be quickly accessed later. There's also a sorted vlan list which is used for stable walks and some user-visible behaviour such as the vlan ranges, also for error paths. VLANs are stored in a "vlan group" which currently contains the rhashtable, sorted vlan list and the number of "real" vlan entries. A good side-effect of this change is that it resembles how hw keeps per-vlan data. One important note after this change is that if a VLAN is being looked up in the bridge's rhashtable for filtering purposes (or to check if it's an existing usable entry, not just a global context) then the new helper br_vlan_should_use() needs to be used if the vlan is found. In case the lookup is done only with a port's vlan group, then this check can be skipped. Things tested so far: - basic vlan ingress/egress - pvids - untagged vlans - undef CONFIG_BRIDGE_VLAN_FILTERING - adding/deleting vlans in different scenarios (with/without global ctx, while transmitting traffic, in ranges etc) - loading/removing the module while having/adding/deleting vlans - extracting bridge vlan information (user ABI), compressed requests - adding/deleting fdbs on vlans - bridge mac change, promisc mode - default pvid change - kmemleak ON during the whole time Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netfilter: Pass net into okfnEric W. Biederman2015-09-171-3/+2
| | | | | | | | | | | | | | | | | | This is immediately motivated by the bridge code that chains functions that call into netfilter. Without passing net into the okfns the bridge code would need to guess about the best expression for the network namespace to process packets in. As net is frequently one of the first things computed in continuation functions after netfilter has done it's job passing in the desired network namespace is in many cases a code simplification. To support this change the function dst_output_okfn is introduced to simplify passing dst_output as an okfn. For the moment dst_output_okfn just silently drops the struct net. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netfilter: Pass struct net into the netfilter hooksEric W. Biederman2015-09-171-6/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pass a network namespace parameter into the netfilter hooks. At the call site of the netfilter hooks the path a packet is taking through the network stack is well known which allows the network namespace to be easily and reliabily. This allows the replacement of magic code like "dev_net(state->in?:state->out)" that appears at the start of most netfilter hooks with "state->net". In almost all cases the network namespace passed in is derived from the first network device passed in, guaranteeing those paths will not see any changes in practice. The exceptions are: xfrm/xfrm_output.c:xfrm_output_resume() xs_net(skb_dst(skb)->xfrm) ipvs/ip_vs_xmit.c:ip_vs_nat_send_or_cont() ip_vs_conn_net(cp) ipvs/ip_vs_xmit.c:ip_vs_send_or_cont() ip_vs_conn_net(cp) ipv4/raw.c:raw_send_hdrinc() sock_net(sk) ipv6/ip6_output.c:ip6_xmit() sock_net(sk) ipv6/ndisc.c:ndisc_send_skb() dev_net(skb->dev) not dev_net(dst->dev) ipv6/raw.c:raw6_send_hdrinc() sock_net(sk) br_netfilter_hooks.c:br_nf_pre_routing_finish() dev_net(skb->dev) before skb->dev is set to nf_bridge->physindev In all cases these exceptions seem to be a better expression for the network namespace the packet is being processed in then the historic "dev_net(in?in:out)". I am documenting them in case something odd pops up and someone starts trying to track down what happened. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Fix network header pointer for vlan tagged packetsToshiaki Makita2015-07-291-7/+22
| | | | | | | | | | | | | | | | | | There are several devices that can receive vlan tagged packets with CHECKSUM_PARTIAL like tap, possibly veth and xennet. When (multiple) vlan tagged packets with CHECKSUM_PARTIAL are forwarded by bridge to a device with the IP_CSUM feature, they end up with checksum error because before entering bridge, the network header is set to ETH_HLEN (not including vlan header length) in __netif_receive_skb_core(), get_rps_cpu(), or drivers' rx functions, and nobody fixes the pointer later. Since the network header is exepected to be ETH_HLEN in flow-dissection and hash-calculation in RPS in rx path, and since the header pointer fix is needed only in tx path, set the appropriate network header on forwarding packets. Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: fix potential crash in __netdev_pick_tx()Eric Dumazet2015-07-091-0/+1
| | | | | | | | | | | | | | | | | Commit c29390c6dfee ("xps: must clear sender_cpu before forwarding") fixed an issue in normal forward path, caused by sender_cpu & napi_id skb fields being an union. Bridge is another point where skb can be forwarded, so we need the same cure. Bug triggers if packet was received on a NIC using skb_mark_napi_id() Fixes: 2bd82484bb4c ("xps: fix xps for stacked devices") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Bob Liu <bob.liu@oracle.com> Tested-by: Bob Liu <bob.liu@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netfilter: Pass socket pointer down through okfn().David Miller2015-04-071-5/+8
| | | | | | | | | | | | | | | | | | | On the output paths in particular, we have to sometimes deal with two socket contexts. First, and usually skb->sk, is the local socket that generated the frame. And second, is potentially the socket used to control a tunneling socket, such as one the encapsulates using UDP. We do not want to disassociate skb->sk when encapsulating in order to fix this, because that would break socket memory accounting. The most extreme case where this can cause huge problems is an AF_PACKET socket transmitting over a vxlan device. We hit code paths doing checks that assume they are dealing with an ipv4 socket, but are actually operating upon the AF_PACKET one. Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller2015-03-091-3/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pablo Neira Ayuso says: ==================== Netfilter updates for net-next The following patchset contains Netfilter updates for your net-next tree. Basically, improvements for the packet rejection infrastructure, deprecation of CLUSTERIP, cleanups for nf_tables and some untangling for br_netfilter. More specifically they are: 1) Send packet to reset flow if checksum is valid, from Florian Westphal. 2) Fix nf_tables reject bridge from the input chain, also from Florian. 3) Deprecate the CLUSTERIP target, the cluster match supersedes it in functionality and it's known to have problems. 4) A couple of cleanups for nf_tables rule tracing infrastructure, from Patrick McHardy. 5) Another cleanup to place transaction declarations at the bottom of nf_tables.h, also from Patrick. 6) Consolidate Kconfig dependencies wrt. NF_TABLES. 7) Limit table names to 32 bytes in nf_tables. 8) mac header copying in bridge netfilter is already required when calling ip_fragment(), from Florian Westphal. 9) move nf_bridge_update_protocol() to br_netfilter.c, also from Florian. 10) Small refactor in br_netfilter in the transmission path, again from Florian. 11) Move br_nf_pre_routing_finish_bridge_slow() to br_netfilter. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * bridge: move mac header copying into br_netfilterFlorian Westphal2015-03-091-3/+1
| | | | | | | | | | | | | | | | | | The mac header only has to be copied back into the skb for fragments generated by ip_fragment(), which only happens for bridge forwarded packets with nf-call-iptables=1 && active nf_defrag. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* | bridge: Extend Proxy ARP design to allow optional rules for Wi-FiJouni Malinen2015-03-051-0/+3
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | This extends the design in commit 958501163ddd ("bridge: Add support for IEEE 802.11 Proxy ARP") with optional set of rules that are needed to meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The previously added BR_PROXYARP behavior is left as-is and a new BR_PROXYARP_WIFI alternative is added so that this behavior can be configured from user space when required. In addition, this enables proxyarp functionality for unicast ARP requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible to use unicast as well as broadcast for these frames. The key differences in functionality: BR_PROXYARP: - uses the flag on the bridge port on which the request frame was received to determine whether to reply - block bridge port flooding completely on ports that enable proxy ARP BR_PROXYARP_WIFI: - uses the flag on the bridge port to which the target device of the request belongs - block bridge port flooding selectively based on whether the proxyarp functionality replied Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2014-11-011-0/+1
|\ | | | | | | | | | | | | | | | | Conflicts: drivers/net/phy/marvell.c Simple overlapping changes in drivers/net/phy/marvell.c Signed-off-by: David S. Miller <davem@davemloft.net>
| * netfilter: nft_reject_bridge: don't use IP stack to reject trafficPablo Neira Ayuso2014-10-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the packet is received via the bridge stack, this cannot reject packets from the IP stack. This adds functions to build the reject packet and send it from the bridge stack. Comments and assumptions on this patch: 1) Validate the IPv4 and IPv6 headers before further processing, given that the packet comes from the bridge stack, we cannot assume they are clean. Truncated packets are dropped, we follow similar approach in the existing iptables match/target extensions that need to inspect layer 4 headers that is not available. This also includes packets that are directed to multicast and broadcast ethernet addresses. 2) br_deliver() is exported to inject the reject packet via bridge localout -> postrouting. So the approach is similar to what we already do in the iptables reject target. The reject packet is sent to the bridge port from which we have received the original packet. 3) The reject packet is forged based on the original packet. The TTL is set based on sysctl_ip_default_ttl for IPv4 and per-net ipv6.devconf_all hoplimit for IPv6. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* | bridge: Add support for IEEE 802.11 Proxy ARPKyeyoon Park2014-10-271-0/+5
|/ | | | | | | | | | | | | | | | | | | | | | | | This feature is defined in IEEE Std 802.11-2012, 10.23.13. It allows the AP devices to keep track of the hardware-address-to-IP-address mapping of the mobile devices within the WLAN network. The AP will learn this mapping via observing DHCP, ARP, and NS/NA frames. When a request for such information is made (i.e. ARP request, Neighbor Solicitation), the AP will respond on behalf of the associated mobile device. In the process of doing so, the AP will drop the multicast request frame that was intended to go out to the wireless medium. It was recommended at the LKS workshop to do this implementation in the bridge layer. vxlan.c is already doing something very similar. The DHCP snooping code will be added to the userspace application (hostapd) per the recommendation. This RFC commit is only for IPv4. A similar approach in the bridge layer will be taken for IPv6 as well. Signed-off-by: Kyeyoon Park <kyeyoonp@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* netfilter: bridge: move br_netfilter out of the corePablo Neira Ayuso2014-09-261-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Jesper reported that br_netfilter always registers the hooks since this is part of the bridge core. This harms performance for people that don't need this. This patch modularizes br_netfilter so it can be rmmod'ed, thus, the hooks can be unregistered. I think the bridge netfilter should have been a separated module since the beginning, Patrick agreed on that. Note that this is breaking compatibility for users that expect that bridge netfilter is going to be available after explicitly 'modprobe bridge' or via automatic load through brctl. However, the damage can be easily undone by modprobing br_netfilter. The bridge core also spots a message to provide a clue to people that didn't notice that this has been deprecated. On top of that, the plan is that nftables will not rely on this software layer, but integrate the connection tracking into the bridge layer to enable stateful filtering and NAT, which is was bridge netfilter users seem to require. This patch still keeps the fake_dst_ops in the bridge core, since this is required by when the bridge port is initialized. So we can safely modprobe/rmmod br_netfilter anytime. Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Florian Westphal <fw@strlen.de>
* bridge: use is_skb_forwardable in forward pathVlad Yasevich2014-03-311-7/+2
| | | | | | | Use existing function instead of trying to use our own. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: remove unnecessary parenthesestanxiaojun2013-12-191-2/+2
| | | | | | | Return is not a function, parentheses are not required. Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: spelling fixestanxiaojun2013-12-181-1/+1
| | | | | | | | Fix spelling errors in bridge driver. Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Add a flag to control unicast packet flood.Vlad Yasevich2013-06-111-5/+9
| | | | | | | | | | | Add a flag to control flood of unicast traffic. By default, flood is on and the bridge will flood unicast traffic if it doesn't know the destination. When the flag is turned off, unicast traffic without an FDB will not be forwarded to the specified port. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Implement vlan ingress/egress policy with PVID.Vlad Yasevich2013-02-131-0/+8
| | | | | | | | | | | At ingress, any untagged traffic is assigned to the PVID. Any tagged traffic is filtered according to membership bitmap. At egress, if the vlan matches the PVID, the frame is sent untagged. Otherwise the frame is sent tagged. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Verify that a vlan is allowed to egress on given portVlad Yasevich2013-02-131-0/+1
| | | | | | | | When bridge forwards a frame, make sure that a frame is allowed to egress on that port. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netpoll: check netpoll tx status on the right deviceAmerigo Wang2012-08-141-1/+1
| | | | | | | | | | | | | Although this doesn't matter actually, because netpoll_tx_running() doesn't use the parameter, the code will be more readable. For team_dev_queue_xmit() we have to move it down to avoid compile errors. Cc: David Miller <davem@davemloft.net> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2012-05-071-0/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/ethernet/intel/e1000e/param.c drivers/net/wireless/iwlwifi/iwl-agn-rx.c drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c drivers/net/wireless/iwlwifi/iwl-trans.h Resolved the iwlwifi conflict with mainline using 3-way diff posted by John Linville and Stephen Rothwell. In 'net' we added a bug fix to make iwlwifi report a more accurate skb->truesize but this conflicted with RX path changes that happened meanwhile in net-next. In e1000e a conflict arose in the validation code for settings of adapter->itr. 'net-next' had more sophisticated logic so that logic was used. Signed-off-by: David S. Miller <davem@davemloft.net>
| * set fake_rtable's dst to NULL to avoid kernel OopsPeter Huang (Peng)2012-04-241-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | bridge: set fake_rtable's dst to NULL to avoid kernel Oops when bridge is deleted before tap/vif device's delete, kernel may encounter an oops because of NULL reference to fake_rtable's dst. Set fake_rtable's dst to NULL before sending packets out can solve this problem. v4 reformat, change br_drop_fake_rtable(skb) to {} v3 enrich commit header v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct. [ Use "do { } while (0)" for nop br_drop_fake_rtable() implementation -DaveM ] Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Peter Huang <peter.huangpeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: cleanup unsigned to unsigned intEric Dumazet2012-04-151-1/+1
|/ | | | | | | Use of "unsigned int" is preferred to bare "unsigned" in net tree. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: add local MAC address to forwarding table (v2)stephen hemminger2011-12-081-1/+1
| | | | | | | | | | | | | If user has configured a MAC address that is not one of the existing ports of the bridge, then we need to add a special entry in the forwarding table. This forwarding table entry has no outgoing port so it has to be treated a little differently. The special entry is reported by the netlink interface with ifindex of bridge, but ignored by the old interface since there is no usable way to put it in the ABI. Reported-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: check the length of skb after nf_bridge_maybe_copy_header()Changli Gao2011-01-061-10/+6
| | | | | | | | Since nf_bridge_maybe_copy_header() may change the length of skb, we should check the length of skb after it to handle the ppoe skbs. Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: add RCU annotation to bridge multicast tableEric Dumazet2010-11-151-2/+2
| | | | | | | | | Add modern __rcu annotatations to bridge multicast table. Use newer hlist macros to avoid direct access to hlist internals. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2010-06-231-2/+2
|\ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: net/ipv4/ip_output.c
| * bridge: Fix OOM crash in deliver_cloneHerbert Xu2010-06-151-2/+2
| | | | | | | | | | | | | | | | | | The bridge multicast patches introduced an OOM crash in the forward path, when deliver_clone fails to clone the skb. Reported-by: Mark Wagner <mwagner@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bridge: Fix netpoll supportHerbert Xu2010-06-151-22/+12
|/ | | | | | | | | | | | | | | | | | | | | | | | | | There are multiple problems with the newly added netpoll support: 1) Use-after-free on each netpoll packet. 2) Invoking unsafe code on netpoll/IRQ path. 3) Breaks when netpoll is enabled on the underlying device. This patch fixes all of these problems. In particular, we now allocate proper netpoll structures for each underlying device. We only allow netpoll to be enabled on the bridge when all the devices underneath it support netpoll. Once it is enabled, we do not allow non-netpoll devices to join the bridge (until netpoll is disabled again). This allows us to do away with the npinfo juggling that caused problem number 1. Incidentally this patch fixes number 2 by bypassing unsafe code such as multicast snooping and netfilter. Reported-by: Qianfeng Zhang <frzhang@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of /repos/git/net-next-2.6Patrick McHardy2010-05-101-10/+29
|\ | | | | | | | | | | | | | | Conflicts: net/bridge/br_device.c net/bridge/br_forward.c Signed-off-by: Patrick McHardy <kaber@trash.net>
| * bridge: make bridge support netpollWANG Cong2010-05-061-1/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on the previous patch, make bridge support netpoll by: 1) implement the 2 methods to support netpoll for bridge; 2) modify netpoll during forwarding packets via bridge; 3) disable netpoll support of bridge when a netpoll-unabled device is added to bridge; 4) enable netpoll support when all underlying devices support netpoll. Cc: David Miller <davem@davemloft.net> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Stephen Hemminger <shemminger@linux-foundation.org> Cc: Matt Mackall <mpm@selenic.com> Signed-off-by: WANG Cong <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>