summaryrefslogtreecommitdiffstats
path: root/net/bridge/br_private.h
Commit message (Collapse)AuthorAgeFilesLines
* net: bridge: Fix VLANs memory leakIdo Schimmel2019-01-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When adding / deleting VLANs to / from a bridge port, the bridge driver first tries to propagate the information via switchdev and falls back to the 8021q driver in case the underlying driver does not support switchdev. This can result in a memory leak [1] when VXLAN and mlxsw ports are enslaved to the bridge: $ ip link set dev vxlan0 master br0 # No mlxsw ports are enslaved to 'br0', so mlxsw ignores the switchdev # notification and the bridge driver adds the VLAN on 'vxlan0' via the # 8021q driver $ bridge vlan add vid 10 dev vxlan0 pvid untagged # mlxsw port is enslaved to the bridge $ ip link set dev swp1 master br0 # mlxsw processes the switchdev notification and the 8021q driver is # skipped $ bridge vlan del vid 10 dev vxlan0 This results in 'struct vlan_info' and 'struct vlan_vid_info' being leaked, as they were allocated by the 8021q driver during VLAN addition, but never freed as the 8021q driver was skipped during deletion. Fix this by introducing a new VLAN private flag that indicates whether the VLAN was added on the port by switchdev or the 8021q driver. If the VLAN was added by the 8021q driver, then we make sure to delete it via the 8021q driver as well. [1] unreferenced object 0xffff88822d20b1e8 (size 256): comm "bridge", pid 2532, jiffies 4295216998 (age 1188.830s) hex dump (first 32 bytes): e0 42 97 ce 81 88 ff ff 00 00 00 00 00 00 00 00 .B.............. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330 [<00000000e0178b02>] vlan_vid_add+0x661/0x920 [<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00 [<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90 [<000000003535392c>] br_vlan_info+0x132/0x410 [<00000000aedaa9dc>] br_afspec+0x75c/0x870 [<00000000f5716133>] br_setlink+0x3dc/0x6d0 [<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30 [<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80 [<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0 [<000000008be8d614>] rtnetlink_rcv+0x21/0x30 [<000000009ab2ca25>] netlink_unicast+0x52f/0x740 [<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50 [<000000005d1e2050>] sock_sendmsg+0xbe/0x120 [<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0 [<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270 unreferenced object 0xffff888227454308 (size 32): comm "bridge", pid 2532, jiffies 4295216998 (age 1188.882s) hex dump (first 32 bytes): 88 b2 20 2d 82 88 ff ff 88 b2 20 2d 82 88 ff ff .. -...... -.... 81 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330 [<0000000018050631>] vlan_vid_add+0x3e6/0x920 [<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00 [<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90 [<000000003535392c>] br_vlan_info+0x132/0x410 [<00000000aedaa9dc>] br_afspec+0x75c/0x870 [<00000000f5716133>] br_setlink+0x3dc/0x6d0 [<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30 [<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80 [<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0 [<000000008be8d614>] rtnetlink_rcv+0x21/0x30 [<000000009ab2ca25>] netlink_unicast+0x52f/0x740 [<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50 [<000000005d1e2050>] sock_sendmsg+0xbe/0x120 [<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0 [<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270 Fixes: d70e42b22dd4 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: bridge@lists.linux-foundation.org Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: support for ndo_fdb_getRoopa Prabhu2018-12-161-0/+3
| | | | | | | | | | This patch implements ndo_fdb_get for the bridge fdb. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Propagate extack to switchdevPetr Machata2018-12-121-9/+13
| | | | | | | | | | | | | | | | ndo_bridge_setlink has been updated in the previous patch to have extack available, and changelink RTNL op has had this argument since the time extack was added. Propagate both through the bridge driver to eventually reach br_switchdev_port_vlan_add(), where it will be used by subsequent patches. Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ndo_bridge_setlink: Add extackPetr Machata2018-12-121-1/+2
| | | | | | | | | | | | | | | | Drivers may not be able to implement a VLAN addition or reconfiguration. In those cases it's desirable to explain to the user that it was rejected (and why). To that end, add extack argument to ndo_bridge_setlink. Adapt all users to that change. Following patches will use the new argument in the bridge driver. Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: increase multicast's default maximum number of entriesNikolay Aleksandrov2018-12-051-0/+2
| | | | | | | | | bridge's default hash_max was 512 which is rather conservative, now that we're using the generic rhashtable API which autoshrinks let's increase it to 4096 and move it to a define in br_private.h. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: mark hash_elasticity as obsoleteNikolay Aleksandrov2018-12-051-1/+0
| | | | | | | | | | Now that the bridge multicast uses the generic rhashtable interface we can drop the hash_elasticity option as that is already done for us and it's hardcoded to a maximum of RHT_ELASTICITY (16 currently). Add a warning about the obsolete option when the hash_elasticity is set. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: multicast: use non-bh rcu flavorNikolay Aleksandrov2018-12-051-1/+0
| | | | | | | | | | | | The bridge multicast code has been using a mix of RCU and RCU-bh flavors sometimes in questionable way. Since we've moved to rhashtable just use non-bh RCU everywhere. In addition this simplifies freeing of objects and allows us to remove some unnecessary callback functions. v3: new patch Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: convert multicast to generic rhashtableNikolay Aleksandrov2018-12-051-18/+20
| | | | | | | | | | | | | | | | | | | | | | The bridge multicast code currently uses a custom resizable hashtable which predates the generic rhashtable interface. It has many shortcomings compared and duplicates functionality that is presently available via the generic rhashtable, so this patch removes the custom rhashtable implementation in favor of the kernel's generic rhashtable. The hash maximum is kept and the rhashtable's size is used to do a loose check if it's reached in which case we revert to the old behaviour and disable further bridge multicast processing. Also now we can support any hash maximum, doesn't need to be a power of 2. v3: add non-rcu br_mdb_get variant and use it where multicast_lock is held to avoid RCU splat, drop hash_max function and just set it directly v2: handle when IGMP snooping is undefined, add br_mdb_init/uninit placeholders Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add no_linklocal_learn bool optionNikolay Aleksandrov2018-11-271-0/+1
| | | | | | | | | | | | | Use the new boolopt API to add an option which disables learning from link-local packets. The default is kept as before and learning is enabled. This is a simple map from a boolopt bit to a bridge private flag that is tested before learning. v2: pass NULL for extack via sysfs Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add support for user-controlled bool optionsNikolay Aleksandrov2018-11-271-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have been adding many new bridge options, a big number of which are boolean but still take up netlink attribute ids and waste space in the skb. Recently we discussed learning from link-local packets[1] and decided yet another new boolean option will be needed, thus introducing this API to save some bridge nl space. The API supports changing the value of multiple boolean options at once via the br_boolopt_multi struct which has an optmask (which options to set, bit per opt) and optval (options' new values). Future boolean options will only be added to the br_boolopt_id enum and then will have to be handled in br_boolopt_toggle/get. The API will automatically add the ability to change and export them via netlink, sysfs can use the single boolopt function versions to do the same. The behaviour with failing/succeeding is the same as with normal netlink option changing. If an option requires mapping to internal kernel flag or needs special configuration to be enabled then it should be handled in br_boolopt_toggle. It should also be able to retrieve an option's current state via br_boolopt_get. v2: WARN_ON() on unsupported option as that shouldn't be possible and also will help catch people who add new options without handling them for both set and get. Pass down extack so if an option desires it could set it on error and be more user-friendly. [1] https://www.spinics.net/lists/netdev/msg532698.html Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2018-11-191-0/+7
|\
| * net: bridge: fix vlan stats use-after-free on destructionNikolay Aleksandrov2018-11-171-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Syzbot reported a use-after-free of the global vlan context on port vlan destruction. When I added per-port vlan stats I missed the fact that the global vlan context can be freed before the per-port vlan rcu callback. There're a few different ways to deal with this, I've chosen to add a new private flag that is set only when per-port stats are allocated so we can directly check it on destruction without dereferencing the global context at all. The new field in net_bridge_vlan uses a hole. v2: cosmetic change, move the check to br_process_vlan_info where the other checks are done v3: add change log in the patch, add private (in-kernel only) flags in a hole in net_bridge_vlan struct and use that instead of mixing user-space flags with private flags Fixes: 9163a0fc1f0c ("net: bridge: add support for per-port vlan stats") Reported-by: syzbot+04681da557a0e49a52e5@syzkaller.appspotmail.com Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | bridge: use __vlan_hwaccel helpersMichał Mirosław2018-11-081-1/+1
|/ | | | | | | This removes assumption than vlan_tci != 0 when tag is present. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: switchdev: Allow clearing FDB entry offload indicationIdo Schimmel2018-10-171-1/+1
| | | | | | | | | | | | | | | | | | | Currently, an FDB entry only ceases being offloaded when it is deleted. This changes with VxLAN encapsulation. Devices capable of performing VxLAN encapsulation usually have only one FDB table, unlike the software data path which has two - one in the bridge driver and another in the VxLAN driver. Therefore, bridge FDB entries pointing to a VxLAN device are only offloaded if there is a corresponding entry in the VxLAN FDB. Allow clearing the offload indication in case the corresponding entry was deleted from the VxLAN FDB. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add support for per-port vlan statsNikolay Aleksandrov2018-10-121-0/+2
| | | | | | | | | | | | | | | | | | This patch adds an option to have per-port vlan stats instead of the default global stats. The option can be set only when there are no port vlans in the bridge since we need to allocate the stats if it is set when vlans are being added to ports (and respectively free them when being deleted). Also bump RTNL_MAX_TYPE as the bridge is the largest user of options. The current stats design allows us to add these without any changes to the fast-path, it all comes down to the per-vlan stats pointer which, if this option is enabled, will be allocated for each port vlan instead of using the global bridge-wide one. CC: bridge@lists.linux-foundation.org CC: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: pack net_bridge betterNikolay Aleksandrov2018-09-261-2/+2
| | | | | | | | | | Further reduce the size of net_bridge with 8 bytes and reduce the number of holes in it: Before: holes: 5, sum holes: 15 After: holes: 3, sum holes: 7 Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: convert mtu_set_by_user to a bitNikolay Aleksandrov2018-09-261-1/+1
| | | | | | | | | Convert the last remaining bool option to a bit thus reducing the overall net_bridge size further by 8 bytes. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: convert neigh_suppress_enabled option to a bitNikolay Aleksandrov2018-09-261-1/+1
| | | | | | | | Convert the neigh_suppress_enabled option to a bit. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: convert mcast options to bitsNikolay Aleksandrov2018-09-261-10/+10
| | | | | | | | | | This patch converts the rest of the mcast options to bits. It also packs the mcast options a little better by moving multicast_mld_version to an existing hole, reducing the net_bridge size by 8 bytes. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: convert and rename mcast disabledNikolay Aleksandrov2018-09-261-1/+1
| | | | | | | | | | | | Convert mcast disabled to an option bit and while doing so convert the logic to check if multicast is enabled instead. That is make the logic follow the option value - if it's set then mcast is enabled and vice versa. This avoids a few confusing places where we inverted the value that's being set to follow the mcast_disabled logic. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: convert group_addr_set option to a bitNikolay Aleksandrov2018-09-261-1/+1
| | | | | | | | Convert group_addr_set internal bridge opt to a bit. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: convert nf call options to bitsNikolay Aleksandrov2018-09-261-3/+3
| | | | | | | | No functional change, convert of nf_call_[ip|ip6|arp]tables to bits. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add bitfield for options and convert vlan optsNikolay Aleksandrov2018-09-261-2/+14
| | | | | | | | | | | | | Bridge options have usually been added as separate fields all over the net_bridge struct taking up space and ending up in different cache lines. Let's move them to a single bitfield to save up space and speedup lookups. This patch adds a simple API for option modifying and retrieving using bitops and converts the first user of the API - the bridge vlan options (vlan_enabled and vlan_stats_enabled). Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: make struct opening bracket consistentNikolay Aleksandrov2018-09-261-8/+4
| | | | | | | | | Currently we have a mix of opening brackets on new lines and on the same line, let's move them all on the same line. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add support for sticky fdb entriesNikolay Aleksandrov2018-09-121-0/+1
| | | | | | | | | Add support for entries which are "sticky", i.e. will not change their port if they show up from a different one. A new ndm flag is introduced for that purpose - NTF_STICKY. We allow to set it only to non-local entries. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add support for backup portNikolay Aleksandrov2018-07-231-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which allows to set a backup port to be used for known unicast traffic if the port has gone carrier down. The backup pointer is rcu protected and set only under RTNL, a counter is maintained so when deleting a port we know how many other ports reference it as a backup and we remove it from all. Also the pointer is in the first cache line which is hot at the time of the check and thus in the common case we only add one more test. The backup port will be used only for the non-flooding case since it's a part of the bridge and the flooded packets will be forwarded to it anyway. To remove the forwarding just send a 0/non-existing backup port. This is used to avoid numerous scalability problems when using MLAG most notably if we have thousands of fdbs one would need to change all of them on port carrier going down which takes too long and causes a storm of fdb notifications (and again when the port comes back up). In a Multi-chassis Link Aggregation setup usually hosts are connected to two different switches which act as a single logical switch. Those switches usually have a control and backup link between them called peerlink which might be used for communication in case a host loses connectivity to one of them. We need a fast way to failover in case a host port goes down and currently none of the solutions (like bond) cannot fulfill the requirements because the participating ports are actually the "master" devices and must have the same peerlink as their backup interface and at the same time all of them must participate in the bridge device. As Roopa noted it's normal practice in routing called fast re-route where a precalculated backup path is used when the main one is down. Another use case of this is with EVPN, having a single vxlan device which is backup of every port. Due to the nature of master devices it's not currently possible to use one device as a backup for many and still have all of them participate in the bridge (which is master itself). More detailed information about MLAG is available at the link below. https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG Further explanation and a diagram by Roopa: Two switches acting in a MLAG pair are connected by the peerlink interface which is a bridge port. the config on one of the switches looks like the below. The other switch also has a similar config. eth0 is connected to one port on the server. And the server is connected to both switches. br0 -- team0---eth0 | -- switch-peerlink Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: make sure objects belong to container's ownerTyler Hicks2018-07-201-0/+2
| | | | | | | | | When creating various bridge objects in /sys/class/net/... make sure that they belong to the container's owner instead of global root (if they belong to a container/namespace). Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Extract boilerplate around switchdev_port_obj_*()Petr Machata2018-05-311-0/+13
| | | | | | | | | | | | | | | | A call to switchdev_port_obj_add() or switchdev_port_obj_del() involves initializing a struct switchdev_obj_port_vlan, a piece of code that repeats on each call site almost verbatim. While in the current codebase there is just one duplicated add call, the follow-up patches add more of both add and del calls. Thus to remove the duplication, extract the repetition into named functions and reuse. Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add support for port isolationNikolay Aleksandrov2018-05-251-0/+9
| | | | | | | | | | | | | | | | This patch adds support for a new port flag - BR_ISOLATED. If it is set then isolated ports cannot communicate between each other, but they can still communicate with non-isolated ports. The same can be achieved via ACLs but they can't scale with large number of ports and also the complexity of the rules grows. This feature can be used to achieve isolated vlan functionality (similar to pvlan) as well, though currently it will be port-wide (for all vlans on the port). The new test in should_deliver uses data that is already cache hot and the new boolean is used to avoid an additional source port test in should_deliver. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Notify about !added_by_user FDB entriesPetr Machata2018-05-031-2/+4
| | | | | | | | | | | | Do not automatically bail out on sending notifications about activity on non-user-added FDB entries. Instead, notify about this activity except for cases where the activity itself originates in a notification, to avoid sending duplicate notifications. Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: avoid duplicate notification on up/down/change netdev eventsNikolay Aleksandrov2018-05-031-1/+1
| | | | | | | | | | | | | While handling netdevice events, br_device_event() sometimes uses br_stp_(disable|enable)_port which unconditionally send a notification, but then a second notification for the same event is sent at the end of the br_device_event() function. To avoid sending duplicate notifications in such cases, check if one has already been sent (i.e. br_stp_enable/disable_port have been called). The patch is based on a change by Satish Ashok. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Publish bridge accessor functionsPetr Machata2018-04-301-0/+11
| | | | | | | | | | Add a couple new functions to allow querying FDB and vlan settings of a bridge. Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: disable bridge MTU auto tuning if it was set manuallyNikolay Aleksandrov2018-03-311-1/+2
| | | | | | | | | | | | | | | | As Roopa noted today the biggest source of problems when configuring bridge and ports is that the bridge MTU keeps changing automatically on port events (add/del/changemtu). That leads to inconsistent behaviour and network config software needs to chase the MTU and fix it on each such event. Let's improve on that situation and allow for the user to set any MTU within ETH_MIN/MAX limits, but once manually configured it is the user's responsibility to keep it correct afterwards. In case the MTU isn't manually set - the behaviour reverts to the previous and the bridge follows the minimum MTU. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: set min MTU on port events and allow user to set maxNikolay Aleksandrov2018-03-311-1/+1
| | | | | | | | | | | | | | | Recently the bridge was changed to automatically set maximum MTU on port events (add/del/changemtu) when vlan filtering is enabled, but that actually changes behaviour in a way which breaks some setups and can lead to packet drops. In order to still allow that maximum to be set while being compatible, we add the ability for the user to tune the bridge MTU up to the maximum when vlan filtering is enabled, but that has to be done explicitly and all port events (add/del/changemtu) lead to resetting that MTU to the minimum as before. Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Allow max MTU when multiple VLANs presentChas Williams2018-03-231-1/+1
| | | | | | | | | | | | | If the bridge is allowing multiple VLANs, some VLANs may have different MTUs. Instead of choosing the minimum MTU for the bridge interface, choose the maximum MTU of the bridge members. With this the user only needs to set a larger MTU on the member ports that are participating in the large MTU VLANS. Signed-off-by: Chas Williams <3chas3@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: return boolean instead of integer in br_multicast_is_routerGustavo A. R. Silva2018-01-221-1/+1
| | | | | | | | | | | | Return statements in functions returning bool should use true/false instead of 1/0. This issue was detected with the help of Coccinelle. Fixes: 85b352693264 ("bridge: Fix build error when IGMP_SNOOPING is not enabled") Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: use rhashtable for fdbsNikolay Aleksandrov2017-12-131-4/+12
| | | | | | | | | | | | | | | | | | | | | | | | Before this patch the bridge used a fixed 256 element hash table which was fine for small use cases (in my tests it starts to degrade above 1000 entries), but it wasn't enough for medium or large scale deployments. Modern setups have thousands of participants in a single bridge, even only enabling vlans and adding a few thousand vlan entries will cause a few thousand fdbs to be automatically inserted per participating port. So we need to scale the fdb table considerably to cope with modern workloads, and this patch converts it to use a rhashtable for its operations thus improving the bridge scalability. Tests show the following results (10 runs each), at up to 1000 entries rhashtable is ~3% slower, at 2000 rhashtable is 30% faster, at 3000 it is 2 times faster and at 30000 it is 50 times faster. Obviously this happens because of the properties of the two constructs and is expected, rhashtable keeps pretty much a constant time even with 10000000 entries (tested), while the fixed hash table struggles considerably even above 10000. As a side effect this also reduces the net_bridge struct size from 3248 bytes to 1344 bytes. Also note that the key struct is 8 bytes. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Rename mglist to host_joinedAndrew Lunn2017-11-101-1/+1
| | | | | | | | | | | The boolean mglist indicates the host has joined a particular multicast group on the bridge interface. It is badly named, obscuring what is means. Rename it. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add notifications for the bridge dev on vlan changeNikolay Aleksandrov2017-11-021-1/+2
| | | | | | | | | | | | | | | | | Currently the bridge device doesn't generate any notifications upon vlan modifications on itself because it doesn't use the generic bridge notifications. With the recent changes we know if anything was modified in the vlan config thus we can generate a notification when necessary for the bridge device so add support to br_ifinfo_notify() similar to how other combined functions are done - if port is present it takes precedence, otherwise notify about the bridge. I've explicitly marked the locations where the notification should be always for the port by setting bridge to NULL. I've also taken the liberty to rearrange each modified function's local variables in reverse xmas tree as well. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: vlan: signal if anything changed on vlan addNikolay Aleksandrov2017-10-291-4/+10
| | | | | | | | | | | | | | | Before this patch there was no way to tell if the vlan add operation actually changed anything, thus we would always generate a notification on adds. Let's make the notifications more precise and generate them only if anything changed, so use the new bool parameter to signal that the vlan was updated. We cannot return an error because there are valid use cases that will be broken (e.g. overlapping range add) and also we can't risk masking errors due to calls into drivers for vlan add which can potentially return anything. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: suppress nd pkts on BR_NEIGH_SUPPRESS portsRoopa Prabhu2017-10-081-0/+3
| | | | | | | | This patch avoids flooding and proxies ndisc packets for BR_NEIGH_SUPPRESS ports. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: suppress arp pkts on BR_NEIGH_SUPPRESS portsRoopa Prabhu2017-10-081-0/+3
| | | | | | | | | | | This patch avoids flooding and proxies arp packets for BR_NEIGH_SUPPRESS ports. Moves existing br_do_proxy_arp to br_do_proxy_suppress_arp to support both proxy arp and neigh suppress. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd floodRoopa Prabhu2017-10-081-0/+2
| | | | | | | | | | | | | | | | | | | | | This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to suppress arp and nd flood on bridge ports. It implements rfc7432, section 10. https://tools.ietf.org/html/rfc7432#section-10 for ethernet VPN deployments. It is similar to the existing BR_PROXYARP* flags but has a few semantic differences to conform to EVPN standard. Unlike the existing flags, this new flag suppresses flood of all neigh discovery packets (arp and nd) to tunnel ports. Supports both vlan filtering and non-vlan filtering bridges. In case of EVPN, it is mainly used to avoid flooding of arp and nd packets to tunnel ports like vxlan. This patch adds netlink and sysfs support to set this bridge port flag. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Pass extack to down to netdev_master_upper_dev_linkDavid Ahern2017-10-041-1/+2
| | | | | | | | | Pass extack arg to br_add_if. Add messages for a couple of failures and pass arg to netdev_master_upper_dev_link. Signed-off-by: David Ahern <dsahern@gmail.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: add per-port group_fwd_mask with less restrictionsNikolay Aleksandrov2017-09-291-1/+9
| | | | | | | | | | | | | | | | We need to be able to transparently forward most link-local frames via tunnels (e.g. vxlan, qinq). Currently the bridge's group_fwd_mask has a mask which restricts the forwarding of STP and LACP, but we need to be able to forward these over tunnels and control that forwarding on a per-port basis thus add a new per-port group_fwd_mask option which only disallows mac pause frames to be forwarded (they're always dropped anyway). The patch does not change the current default situation - all of the others are still restricted unless configured for forwarding. We have successfully tested this patch with LACP and STP forwarding over VxLAN and qinq tunnels. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: switchdev: Use an helper to clear forward markIdo Schimmel2017-09-051-0/+9
| | | | | | | | | | Instead of using ifdef in the C file. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Tested-by: Yotam Gigi <yotamg@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net, bridge: convert net_bridge_vlan.refcnt from atomic_t to refcount_tReshetova, Elena2017-07-041-1/+2
| | | | | | | | | | | | | | refcount_t type and corresponding API should be used instead of atomic_t when the variable is used as a reference counter. This allows to avoid accidental refcounter overflows that might lead to use-after-free situations. Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Receive notification about successful FDB offloadArkadi Sharshevsky2017-06-081-1/+4
| | | | | | | | | | | | | | | | | When a new static FDB is added to the bridge a notification is sent to the driver for offload. In case of successful offload the driver should notify the bridge back, which in turn should mark the FDB as offloaded. Currently, externally learned is equivalent for being offloaded which is not correct due to the fact that FDBs which are added from user-space are also marked as externally learned. In order to specify if an FDB was successfully offloaded a new flag is introduced. Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Add support for notifying devices about FDB add/delArkadi Sharshevsky2017-06-081-0/+7
| | | | | | | | | | | | | | | | | | | | | | | Currently the bridge doesn't notify the underlying devices about new FDBs learned. The FDB sync is placed on the switchdev notifier chain because devices may potentially learn FDB that are not directly related to their ports, for example: 1. Mixed SW/HW bridge - FDBs that point to the ASICs external devices should be offloaded as CPU traps in order to perform forwarding in slow path. 2. EVPN - Externally learned FDBs for the vtep device. Notification is sent only about static FDB add/del. This is done due to fact that currently this is the only scenario supported by switch drivers. Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: bridge: Add support for calling FDB external learning under rcuArkadi Sharshevsky2017-06-081-0/+6
| | | | | | | | | | | | This is done as a preparation to moving the switchdev notifier chain to be atomic. The FDB external learning should be called under rtnl or rcu. Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 07:19:31 +0000