summaryrefslogtreecommitdiffstats
path: root/net/ipv6/ip6_gre.c
Commit message (Collapse)AuthorAgeFilesLines
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2016-03-081-0/+2
|\ | | | | | | | | | | | | | | Several cases of overlapping changes, as well as one instance (vxlan) of a bug fix in 'net' overlapping with code movement in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * tunnel: Clear IPCB(skb)->opt before dst_link_failure calledBernie Harris2016-02-231-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | IPCB may contain data from previous layers (in the observed case the qdisc layer). In the observed scenario, the data was misinterpreted as ip header options, which later caused the ihl to be set to an invalid value (<5). This resulted in an infinite loop in the mips implementation of ip_fast_csum. This patch clears IPCB(skb)->opt before dst_link_failure can be called for various types of tunnels. This change only applies to encapsulated ipv4 packets. The code introduced in 11c21a30 which clears all of IPCB has been removed to be consistent with these changes, and instead the opt field is cleared unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to SIT, GRE, and IPIP tunnels. The relevant vti, l2tp, and pptp functions already contain similar code for clearing the IPCB. Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2016-02-231-0/+1
|\| | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/phy/bcm7xxx.c drivers/net/phy/marvell.c drivers/net/vxlan.c All three conflicts were cases of simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
| * gre: clear IFF_TX_SKB_SHARINGJiri Benc2016-02-181-0/+1
| | | | | | | | | | | | | | | | | | | | ether_setup sets IFF_TX_SKB_SHARING but this is not supported by gre as it modifies the skb on xmit. Also, clean up whitespace in ipgre_tap_setup when we're already touching it. Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: replace dst_cache ip6_tunnel implementation with the generic onePaolo Abeni2016-02-161-6/+6
|/ | | | | | | | | | | | | | | | | | | | | | | | This also fix a potential race into the existing tunnel code, which could lead to the wrong dst to be permanenty cached: CPU1: CPU2: <xmit on ip6_tunnel> <cache lookup fails> dst = ip6_route_output(...) <tunnel params are changed via nl> dst_cache_reset() // no effect, // the cache is empty dst_cache_set() // the wrong dst // is permanenty stored // into the cache With the new dst implementation the above race is not possible since the first cache lookup after dst_cache_reset will fail due to the timestamp check Signed-off-by: Paolo Abeni <pabeni@redhat.com> Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-12-171-5/+3
|\ | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/geneve.c Here we had an overlapping change, where in 'net' the extraneous stats bump was being removed whilst in 'net-next' the final argument to udp_tunnel6_xmit_skb() was being changed. Signed-off-by: David S. Miller <davem@davemloft.net>
| * gre6: allow to update all parameters via rtnlNicolas Dichtel2015-12-041-5/+3
| | | | | | | | | | | | | | | | | | | | | | Parameters were updated only if the kernel was unable to find the tunnel with the new parameters, ie only if core pamareters were updated (keys, addr, link, type). Now it's possible to update ttl, hoplimit, flowinfo and flags. Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: remove unnecessary mroute.h includesNikolay Aleksandrov2015-11-301-1/+0
|/ | | | | | | | | | | It looks like many files are including mroute.h unnecessarily, so remove the include. Most importantly remove it from ipv6. CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> CC: Steffen Klassert <steffen.klassert@secunet.com> CC: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ip6_gre: Reduce log level in ip6gre_err() to debugMatt Bennett2015-09-241-8/+8
| | | | | | | | | | | | | | | Currently error log messages in ip6gre_err are printed at 'warn' level. This is different to most other tunnel types which don't print any messages. These log messages don't provide any information that couldn't be deduced with networking tools. Also it can be annoying to have one end of the tunnel go down and have the logs fill with pointless messages such as "Path to destination invalid or inactive!". This patch reduces the log level of these messages to 'dbg' level to bring the visible behaviour into line with other tunnel types. Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: Fix dst_entry refcnt bugs in ip6_tunnelMartin KaFai Lau2015-09-151-16/+22
| | | | | | | | | | | | | | | | | | | | | | | | | Problems in the current dst_entry cache in the ip6_tunnel: 1. ip6_tnl_dst_set is racy. There is no lock to protect it: - One major problem is that the dst refcnt gets messed up. F.e. the same dst_cache can be released multiple times and then triggering the infamous dst refcnt < 0 warning message. - Another issue is the inconsistency between dst_cache and dst_cookie. It can be reproduced by adding and removing the ip6gre tunnel while running a super_netperf TCP_CRR test. 2. ip6_tnl_dst_get does not take the dst refcnt before returning the dst. This patch: 1. Create a percpu dst_entry cache in ip6_tnl 2. Use a spinlock to protect the dst_cache operations 3. ip6_tnl_dst_get always takes the dst refcnt before returning Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: Rename the dst_cache helper functions in ip6_tunnelMartin KaFai Lau2015-09-151-2/+2
| | | | | | | | | | | | | | It is a prep work to fix the dst_entry refcnt bugs in ip6_tunnel. This patch rename: 1. ip6_tnl_dst_check() to ip6_tnl_dst_get() to better reflect that it will take a dst refcnt in the next patch. 2. ip6_tnl_dst_store() to ip6_tnl_dst_set() to have a more conventional name matching with ip6_tnl_dst_get(). Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: Refactor common ip6gre_tunnel_init codesMartin KaFai Lau2015-09-151-13/+24
| | | | | | | | | | It is a prep work to fix the dst_entry refcnt bugs in ip6_tunnel. This patch refactors some common init codes used by both ip6gre_tunnel_init and ip6gre_tap_init. Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-08-271-0/+1
|\
| * ip6_gre: release cached dst on tunnel removalhuaibin Wang2015-08-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | When a tunnel is deleted, the cached dst entry should be released. This problem may prevent the removal of a netns (seen with a x-netns IPv6 gre tunnel): unregister_netdevice: waiting for lo to become free. Usage count = 3 CC: Dmitry Kozlov <xeb@mail.ru> Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: huaibin Wang <huaibin.wang@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ipv6: Implement different admin modes for automatic flow labelsTom Herbert2015-07-311-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the meaning of net.ipv6.auto_flowlabels to provide a mode for automatic flow labels generation. There are four modes: 0: flow labels are disabled 1: flow labels are enabled, sockets can opt-out 2: flow labels are allowed, sockets can opt-in 3: flow labels are enabled and enforced, no opt-out for sockets np->autoflowlabel is initialized according to the sysctl value. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabelTom Herbert2015-07-311-2/+3
|/ | | | | | | | We can't call skb_get_hash here since the packet is not complete to do flow_dissector. Create hash based on flowi6 instead. Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ip6_gre: use netdev_alloc_pcpu_stats()Johannes Berg2015-04-221-8/+1
| | | | | | | The code there just open-codes the same, so use the provided macro instead. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* udp_tunnel: Pass UDP socket down through udp_tunnel{, 6}_xmit_skb().David Miller2015-04-071-1/+1
| | | | | | | | | | | That was we can make sure the output path of ipv4/ipv6 operate on the UDP socket rather than whatever random thing happens to be in skb->sk. Based upon a patch by Jiri Pirko. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
* ip6tnl,gre6,vti6: implement ndo_get_iflinkNicolas Dichtel2015-04-021-6/+2
| | | | | | | | Don't use dev->iflink anymore. CC: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netlink: implement nla_get_in_addr and nla_get_in6_addrJiri Benc2015-03-311-3/+3
| | | | | | | Those are counterparts to nla_put_in_addr and nla_put_in6_addr. Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netlink: implement nla_put_in_addr and nla_put_in6_addrJiri Benc2015-03-311-2/+2
| | | | | | | | | | | | IP addresses are often stored in netlink attributes. Add generic functions to do that. For nla_put_in_addr, it would be nicer to pass struct in_addr but this is not used universally throughout the kernel, in way too many places __be32 is used to store IPv4 address. Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: coding style: comparison for inequality with NULLIan Morris2015-03-311-3/+3
| | | | | | | | | | | | The ipv6 code uses a mixture of coding styles. In some instances check for NULL pointer is done as x != NULL and sometimes as x. x is preferred according to checkpatch and this patch makes the code consistent by adopting the latter form. No changes detected by objdiff. Signed-off-by: Ian Morris <ipm@chirality.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: coding style: comparison for equality with NULLIan Morris2015-03-311-4/+4
| | | | | | | | | | | | The ipv6 code uses a mixture of coding styles. In some instances check for NULL pointer is done as x == NULL and sometimes as !x. !x is preferred according to checkpatch and this patch makes the code consistent by adopting the latter form. No changes detected by objdiff. Signed-off-by: Ian Morris <ipm@chirality.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-02-051-2/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/vxlan.c drivers/vhost/net.c include/linux/if_vlan.h net/core/dev.c The net/core/dev.c conflict was the overlap of one commit marking an existing function static whilst another was adding a new function. In the include/linux/if_vlan.h case, the type used for a local variable was changed in 'net', whereas the function got rewritten to fix a stacked vlan bug in 'net-next'. In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next' overlapped with an endainness fix for VHOST 1.0 in 'net'. In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter in 'net-next' whereas in 'net' there was a bug fix to pass in the correct network namespace pointer in calls to this function. Signed-off-by: David S. Miller <davem@davemloft.net>
| * ip6_gre: fix endianness errors in ip6gre_errSabrina Dubroca2015-02-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | info is in network byte order, change it back to host byte order before use. In particular, the current code sets the MTU of the tunnel to a wrong (too big) value. Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ip6gretap: advertise link netns via netlinkNicolas Dichtel2015-01-231-0/+1
| | | | | | | | | | | | | | | | Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is added to rtnetlink messages. Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | tunnels: advertise link netns via netlinkNicolas Dichtel2015-01-191-0/+1
|/ | | | | | | | Implement rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is added to rtnetlink messages. Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2014-11-291-2/+2
|\
| * ipv6: gre: fix wrong skb->protocol in WCCPYuri Chislov2014-11-241-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | When using GRE redirection in WCCP, it sets the wrong skb->protocol, that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic. Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Cc: Dmitry Kozlov <xeb@mail.ru> Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com> Tested-by: Yuri Chislov <yuri.chislov@gmail.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2014-11-061-2/+3
|\|
| * gre6: Move the setting of dev->iflink into the ndo_init functions.Steffen Klassert2014-11-031-2/+3
| | | | | | | | | | | | | | Otherwise it gets overwritten by register_netdev(). Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | ipv6: Allow sending packets through tunnels with wildcard endpointsSteffen Klassert2014-11-061-1/+1
|/ | | | | | | | | | | | | | | | | Currently we need the IP6_TNL_F_CAP_XMIT capabiltiy to transmit packets through an ipv6 tunnel. This capability is set when the tunnel gets configured, based on the tunnel endpoint addresses. On tunnels with wildcard tunnel endpoints, we need to do the capabiltiy checking on a per packet basis like it is done in the receive path. This patch extends ip6_tnl_xmit_ctl() to take local and remote addresses as parameters to allow for per packet capabiltiy checking. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2014-10-081-2/+2
|\
| * ip6_gre: fix flowi6_proto value in xmit pathNicolas Dichtel2014-10-041-2/+2
| | | | | | | | | | | | | | | | | | | | | | In xmit path, we build a flowi6 which will be used for the output route lookup. We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the protocol should be IPPROTO_GRE. Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Reported-by: Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: better IFF_XMIT_DST_RELEASE supportEric Dumazet2014-10-071-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Testing xmit_more support with netperf and connected UDP sockets, I found strange dst refcount false sharing. Current handling of IFF_XMIT_DST_RELEASE is not optimal. Dropping dst in validate_xmit_skb() is certainly too late in case packet was queued by cpu X but dequeued by cpu Y The logical point to take care of drop/force is in __dev_queue_xmit() before even taking qdisc lock. As Julian Anastasov pointed out, need for skb_dst() might come from some packet schedulers or classifiers. This patch adds new helper to cleanly express needs of various drivers or qdiscs/classifiers. Drivers that need skb_dst() in their ndo_start_xmit() should call following helper in their setup instead of the prior : dev->priv_flags &= ~IFF_XMIT_DST_RELEASE; -> netif_keep_dst(dev); Instead of using a single bit, we use two bits, one being eventually rebuilt in bonding/team drivers. The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being rebuilt in bonding/team. Eventually, we could add something smarter later. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2014-10-021-0/+3
|\| | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/usb/r8152.c net/netfilter/nfnetlink.c Both r8152 and nfnetlink conflicts were simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
| * ip6_gre: Return an error when adding an existing tunnel.Steffen Klassert2014-09-281-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | ip6gre_tunnel_locate() should not return an existing tunnel if create is true. Otherwise it is possible to add the same tunnel multiple times without getting an error. So return NULL if the tunnel that should be created already exists. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * ip6gre: add a rtnl link alias for ip6gretapNicolas Dichtel2014-09-261-0/+1
| | | | | | | | | | | | | | | | With this alias, we don't need to load manually the module before adding an ip6gretap interface with iproute2. Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | gre: Set inner protocol in v4 and v6 GRE transmitTom Herbert2014-10-011-2/+6
|/ | | | | | | | | Call skb_set_inner_protocol to set inner Ethernet protocol to protocol being encapsulation by GRE before tunnel_xmit. This is needed for GSO if UDP encapsulation (fou) is being done. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: set name_assign_type in alloc_netdev()Tom Gundersen2014-07-151-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert all users to pass NET_NAME_UNKNOWN. Coccinelle patch: @@ expression sizeof_priv, name, setup, txqs, rxqs, count; @@ ( -alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs) +alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs) | -alloc_netdev_mq(sizeof_priv, name, setup, count) +alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count) | -alloc_netdev(sizeof_priv, name, setup) +alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup) ) v9: move comments here from the wrong commit Signed-off-by: Tom Gundersen <teg@jklm.no> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: Implement automatic flow label generation on transmitTom Herbert2014-07-071-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Automatically generate flow labels for IPv6 packets on transmit. The flow label is computed based on skb_get_hash. The flow label will only automatically be set when it is zero otherwise (i.e. flow label manager hasn't set one). This supports the transmit side functionality of RFC 6438. Added an IPv6 sysctl auto_flowlabels to enable/disable this behavior system wide, and added IPV6_AUTOFLOWLABEL socket option to enable this functionality per socket. By default, auto flowlabels are disabled to avoid possible conflicts with flow label manager, however if this feature proves useful we may want to enable it by default. It should also be noted that FreeBSD has already implemented automatic flow labels (including the sysctl and socket option). In FreeBSD, automatic flow labels default to enabled. Performance impact: Running super_netperf with 200 flows for TCP_RR and UDP_RR for IPv6. Note that in UDP case, __skb_get_hash will be called for every packet with explains slight regression. In the TCP case the hash is saved in the socket so there is no regression. Automatic flow labels disabled: TCP_RR: 86.53% CPU utilization 127/195/322 90/95/99% latencies 1.40498e+06 tps UDP_RR: 90.70% CPU utilization 118/168/243 90/95/99% latencies 1.50309e+06 tps Automatic flow labels enabled: TCP_RR: 85.90% CPU utilization 128/199/337 90/95/99% latencies 1.40051e+06 UDP_RR 92.61% CPU utilization 115/164/236 90/95/99% latencies 1.4687e+06 Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* gre6: Call skb_checksum_simple_validateTom Herbert2014-05-081-11/+1
| | | | | | | Use skb_checksum_simple_validate to verify checksum. Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ip6gre: add x-netns supportNicolas Dichtel2014-04-231-20/+32
| | | | | | | | | | | | | This patch allows to switch the netns when packet is encapsulated or decapsulated. In other word, the encapsulated packet is received in a netns, where the lookup is done to find the tunnel. Once the tunnel is found, the packet is decapsulated and injecting into the corresponding interface which stands to another netns. When one of the two netns is removed, the tunnel is destroyed. Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ip6_gre: don't allow to remove the fb_tunnel_devNicolas Dichtel2014-04-151-0/+10
| | | | | | | | | | | | | | | It's possible to remove the FB tunnel with the command 'ip link del ip6gre0' but this is unsafe, the module always supposes that this device exists. For example, ip6gre_tunnel_lookup() may use it unconditionally. Let's add a rtnl handler for dellink, which will never remove the FB tunnel (we let ip6gre_destroy_tunnels() do the job). Introduced by commit c12b395a4664 ("gre: Support GRE over IPv6"). CC: Dmitry Kozlov <xeb@mail.ru> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: introduce netdev_alloc_pcpu_stats() for driversWANG Cong2014-02-141-8/+1
| | | | | | | | | There are many drivers calling alloc_percpu() to allocate pcpu stats and then initializing ->syncp. So just introduce a helper function for them. Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: move IPV6_TCLASS_SHIFT into ipv6.h and define a helperLi RongQing2014-01-151-2/+0
| | | | | | | | | Two places defined IPV6_TCLASS_SHIFT, so we should move it into ipv6.h, and use this macro as possible. And define ip6_tclass helper to return tclass Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: unify the pcpu_tstats and br_cpu_netstats as oneLi RongQing2014-01-041-5/+5
| | | | | | | | | | | | They are same, so unify them as one, pcpu_sw_netstats. Define pcpu_sw_netstat in netdevice.h, remove pcpu_tstats from if_tunnel and remove br_cpu_netstats from br_private.h Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Li RongQing <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: add ip6_flowlabel helperFlorent Fourcot2013-12-091-1/+1
| | | | | | | | And use it if possible. Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr> Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: move IPV6_TCLASS_MASK definition in ipv6.hFlorent Fourcot2013-12-091-1/+0
| | | | | | Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr> Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Explicitly initialize u64_stats_sync structures for lockdepJohn Stultz2013-11-061-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In order to enable lockdep on seqcount/seqlock structures, we must explicitly initialize any locks. The u64_stats_sync structure, uses a seqcount, and thus we need to introduce a u64_stats_init() function and use it to initialize the structure. This unfortunately adds a lot of fairly trivial initialization code to a number of drivers. But the benefit of ensuring correctness makes this worth while. Because these changes are required for lockdep to be enabled, and the changes are quite trivial, I've not yet split this patch out into 30-some separate patches, as I figured it would be better to get the various maintainers thoughts on how to best merge this change along with the seqcount lockdep enablement. Feedback would be appreciated! Signed-off-by: John Stultz <john.stultz@linaro.org> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: James Morris <jmorris@namei.org> Cc: Jesse Gross <jesse@nicira.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Mirko Lindner <mlindner@marvell.com> Cc: Patrick McHardy <kaber@trash.net> Cc: Roger Luethi <rl@hellgate.ch> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Simon Horman <horms@verge.net.au> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Wensong Zhang <wensong@linux-vs.org> Cc: netdev@vger.kernel.org Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 04:17:46 +0000