From 89d8232411a85b9a6b12fd5da4d07d8a138a8e0c Mon Sep 17 00:00:00 2001 From: Richard Genoud Date: Tue, 13 Dec 2016 17:27:56 +0100 Subject: tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx If we don't disable the transmitter in atmel_stop_tx, the DMA buffer continues to send data until it is emptied. This cause problems with the flow control (CTS is asserted and data are still sent). So, disabling the transmitter in atmel_stop_tx is a sane thing to do. Tested on at91sam9g35-cm(DMA) Tested for regressions on sama5d2-xplained(Fifo) and at91sam9g20ek(PDC) Cc: (beware, this won't apply before 4.3) Signed-off-by: Richard Genoud Acked-by: Nicolas Ferre Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/atmel_serial.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index 168b10cad47b..f9d42de5ab2d 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -481,6 +481,14 @@ static void atmel_stop_tx(struct uart_port *port) /* disable PDC transmit */ atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); } + + /* + * Disable the transmitter. + * This is mandatory when DMA is used, otherwise the DMA buffer + * is fully transmitted. + */ + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS); + /* Disable interrupts */ atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); @@ -513,6 +521,9 @@ static void atmel_start_tx(struct uart_port *port) /* Enable interrupts */ atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); + + /* re-enable the transmitter */ + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN); } /* -- cgit v1.2.3 From b389f173aaa1204d6dc1f299082a162eb0491545 Mon Sep 17 00:00:00 2001 From: Richard Genoud Date: Tue, 6 Dec 2016 13:05:33 +0100 Subject: tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done When using RS485 in half duplex, RX should be enabled when TX is finished, and stopped when TX starts. Before commit 0058f0871efe7b01c6 ("tty/serial: atmel: fix RS485 half duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA was used. So, collisions could happened. But disabling RX in atmel_start_tx() uncovered another bug: RX was enabled again in the wrong place (in atmel_tx_dma) instead of being enabled when TX is finished (in atmel_complete_tx_dma), so the transmission simply stopped. This bug was not triggered before commit 0058f0871efe7b01c6 ("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was never disabled before. Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem. Cc: stable@vger.kernel.org Reported-by: Gil Weber Fixes: 0058f0871efe7b01c6 Tested-by: Gil Weber Signed-off-by: Richard Genoud Acked-by: Alexandre Belloni Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/atmel_serial.c | 11 +++++------ 1 file changed, 5 insertions(+), 6 deletions(-) diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index f9d42de5ab2d..fabbe76203bb 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -809,6 +809,11 @@ static void atmel_complete_tx_dma(void *arg) */ if (!uart_circ_empty(xmit)) atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx); + else if ((port->rs485.flags & SER_RS485_ENABLED) && + !(port->rs485.flags & SER_RS485_RX_DURING_TX)) { + /* DMA done, stop TX, start RX for RS485 */ + atmel_start_rx(port); + } spin_unlock_irqrestore(&port->lock, flags); } @@ -911,12 +916,6 @@ static void atmel_tx_dma(struct uart_port *port) desc->callback = atmel_complete_tx_dma; desc->callback_param = atmel_port; atmel_port->cookie_tx = dmaengine_submit(desc); - - } else { - if (port->rs485.flags & SER_RS485_ENABLED) { - /* DMA done, stop TX, start RX for RS485 */ - atmel_start_rx(port); - } } if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) -- cgit v1.2.3 From c130b666a9a711f985a0a44b58699ebe14bb7245 Mon Sep 17 00:00:00 2001 From: Gabriel Krisman Bertazi Date: Wed, 28 Dec 2016 16:42:00 -0200 Subject: 8250_pci: Fix potential use-after-free in error path Commit f209fa03fc9d ("serial: 8250_pci: Detach low-level driver during PCI error recovery") introduces a potential use-after-free in case the pciserial_init_ports call in serial8250_io_resume fails, which may happen if a memory allocation fails or if the .init quirk failed for whatever reason). If this happen, further pci_get_drvdata will return a pointer to freed memory. This patch reworks the PCI recovery resume hook to restore the old priv structure in this case, which should be ok, since the ports were already detached. Such error during recovery causes us to give up on the recovery. Fixes: f209fa03fc9d ("serial: 8250_pci: Detach low-level driver during PCI error recovery") Reported-by: Michal Suchanek Signed-off-by: Gabriel Krisman Bertazi Signed-off-by: Guilherme G. Piccoli Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_pci.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-) diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index aa0166b6d450..116436b7fa52 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -5642,17 +5642,15 @@ static pci_ers_result_t serial8250_io_slot_reset(struct pci_dev *dev) static void serial8250_io_resume(struct pci_dev *dev) { struct serial_private *priv = pci_get_drvdata(dev); - const struct pciserial_board *board; + struct serial_private *new; if (!priv) return; - board = priv->board; - kfree(priv); - priv = pciserial_init_ports(dev, board); - - if (!IS_ERR(priv)) { - pci_set_drvdata(dev, priv); + new = pciserial_init_ports(dev, priv->board); + if (!IS_ERR(new)) { + pci_set_drvdata(dev, new); + kfree(priv); } } -- cgit v1.2.3 From 2bed8a8e70729f996af92042d3ad0f11870acc1f Mon Sep 17 00:00:00 2001 From: Daniel Jedrychowski Date: Mon, 12 Dec 2016 09:18:28 +1100 Subject: Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break When in RS485 emulation mode, __do_stop_tx_rs485() calls serial8250_clear_fifos(). This not only clears the FIFOs, but also sets all bits in their control register (UART_FCR) to 0. One of the effects of this is the disabling of the FIFOs, which turns them into single-byte holding registers. The rest of the driver doesn't know this, which results in the lions share of characters passed into a write call to be dropped. (I can supply logic analyzer screenshots if necessary) This fix replaces the serial8250_clear_fifos() call to serial8250_clear_and_reinit_fifos() - this prevents the "dropped characters" issue from manifesting again while retaining the requirement of clearing the RX FIFO after transmission if the SER_RS485_RX_DURING_TX flag is disabled. Signed-off-by: Daniel Jedrychowski Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_port.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c index fe4399b41df6..c13fec451d03 100644 --- a/drivers/tty/serial/8250/8250_port.c +++ b/drivers/tty/serial/8250/8250_port.c @@ -1413,7 +1413,7 @@ static void __do_stop_tx_rs485(struct uart_8250_port *p) * Enable previously disabled RX interrupts. */ if (!(p->port.rs485.flags & SER_RS485_RX_DURING_TX)) { - serial8250_clear_fifos(p); + serial8250_clear_and_reinit_fifos(p); p->ier |= UART_IER_RLSI | UART_IER_RDI; serial_port_out(&p->port, UART_IER, p->ier); -- cgit v1.2.3 From 6741f551a0b26479de2532ffa43a366747e6dbf3 Mon Sep 17 00:00:00 2001 From: Herbert Xu Date: Sun, 11 Dec 2016 10:05:49 +0800 Subject: Revert "tty: serial: 8250: add CON_CONSDEV to flags" This commit needs to be reverted because it prevents people from using the serial console as a secondary console with input being directed to tty0. IOW, if you boot with console=ttyS0 console=tty0 then all kernels prior to this commit will produce output on both ttyS0 and tty0 but input will only be taken from tty0. With this patch the serial console will always be the primary console instead of tty0, potentially preventing people from getting into their machines in emergency situations. Fixes: d03516df8375 ("tty: serial: 8250: add CON_CONSDEV to flags") Signed-off-by: Herbert Xu Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index 61569a765d9e..76e03a7de9cc 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -675,7 +675,7 @@ static struct console univ8250_console = { .device = uart_console_device, .setup = univ8250_console_setup, .match = univ8250_console_match, - .flags = CON_PRINTBUFFER | CON_ANYTIME | CON_CONSDEV, + .flags = CON_PRINTBUFFER | CON_ANYTIME, .index = -1, .data = &serial8250_reg, }; -- cgit v1.2.3 From 802c03881f29844af0252b6e22be5d2f65f93fd0 Mon Sep 17 00:00:00 2001 From: Akinobu Mita Date: Fri, 6 Jan 2017 02:14:16 +0900 Subject: sysrq: attach sysrq handler correctly for 32-bit kernel The sysrq input handler should be attached to the input device which has a left alt key. On 32-bit kernels, some input devices which has a left alt key cannot attach sysrq handler. Because the keybit bitmap in struct input_device_id for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is greater than BITS_PER_LONG on 32-bit kernels. I found this problem when using a matrix keypad device which defines a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32). Cc: Jiri Slaby Signed-off-by: Akinobu Mita Acked-by: Dmitry Torokhov Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/tty/sysrq.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/tty/sysrq.c b/drivers/tty/sysrq.c index 52bbd27e93ae..701c085bb19b 100644 --- a/drivers/tty/sysrq.c +++ b/drivers/tty/sysrq.c @@ -946,8 +946,8 @@ static const struct input_device_id sysrq_ids[] = { { .flags = INPUT_DEVICE_ID_MATCH_EVBIT | INPUT_DEVICE_ID_MATCH_KEYBIT, - .evbit = { BIT_MASK(EV_KEY) }, - .keybit = { BIT_MASK(KEY_LEFTALT) }, + .evbit = { [BIT_WORD(EV_KEY)] = BIT_MASK(EV_KEY) }, + .keybit = { [BIT_WORD(KEY_LEFTALT)] = BIT_MASK(KEY_LEFTALT) }, }, { }, }; -- cgit v1.2.3