From d2cdfc0db39247518585db13a3abdc633a158e0e Mon Sep 17 00:00:00 2001 From: Alan Date: Wed, 10 Jan 2007 17:13:38 +0000 Subject: libata: PIIX3 support This I believe completes the PIIX range of support for libata This adds the table entries needed for the PIIX3, both a new PCI identifier and a new mode list. It also fixes an erroneous access to PCI configuration 0x48 on non UDMA capable chips. Signed-off-by: Alan Cox Signed-off-by: Jeff Garzik --- drivers/ata/ata_piix.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-) diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index aadfcb3ceb1b..33bbeac785cc 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -118,7 +118,7 @@ enum { PIIX_80C_SEC = (1 << 7) | (1 << 6), /* controller IDs */ - piix_pata_33 = 0, /* PIIX3 or 4 at 33Mhz */ + piix_pata_33 = 0, /* PIIX4 at 33Mhz */ ich_pata_33 = 1, /* ICH up to UDMA 33 only */ ich_pata_66 = 2, /* ICH up to 66 Mhz */ ich_pata_100 = 3, /* ICH up to UDMA 100 */ @@ -128,6 +128,7 @@ enum { ich6_sata_ahci = 7, ich6m_sata_ahci = 8, ich8_sata_ahci = 9, + piix_pata_mwdma = 10, /* PIIX3 MWDMA only */ /* constants for mapping table */ P0 = 0, /* port 0 */ @@ -165,6 +166,8 @@ static unsigned int in_module_init = 1; static const struct pci_device_id piix_pci_tbl[] = { #ifdef ATA_ENABLE_PATA + /* Intel PIIX3 for the 430HX etc */ + { 0x8086, 0x7010, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_mwdma }, /* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */ /* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */ { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 }, @@ -441,7 +444,7 @@ static const struct piix_map_db *piix_map_db_table[] = { }; static struct ata_port_info piix_port_info[] = { - /* piix_pata_33: 0: PIIX3 or 4 at 33MHz */ + /* piix_pata_33: 0: PIIX4 at 33MHz */ { .sht = &piix_sht, .flags = PIIX_PATA_FLAGS, @@ -543,6 +546,14 @@ static struct ata_port_info piix_port_info[] = { .port_ops = &piix_sata_ops, }, + /* piix_pata_mwdma: 10: PIIX3 MWDMA only */ + { + .sht = &piix_sht, + .flags = PIIX_PATA_FLAGS, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */ + .port_ops = &piix_pata_ops, + }, }; static struct pci_bits piix_enable_bits[] = { @@ -787,7 +798,8 @@ static void do_pata_set_dmamode (struct ata_port *ap, struct ata_device *adev, i { 2, 3 }, }; pci_read_config_word(dev, master_port, &master_data); - pci_read_config_byte(dev, 0x48, &udma_enable); + if (ap->udma_mask) + pci_read_config_byte(dev, 0x48, &udma_enable); if (speed >= XFER_UDMA_0) { unsigned int udma = adev->dma_mode - XFER_UDMA_0; -- cgit v1.2.3