From ee03672d961bdac2ac1e593e9c29b0d3b7320409 Mon Sep 17 00:00:00 2001 From: Jarkko Nikula Date: Tue, 26 Jan 2016 15:33:21 +0200 Subject: spi: pxa2xx: Print actual DMA/PIO transfer mode in debug messages Transfer debug messages don't actually show is the transfer really using DMA. Driver may fall back to PIO in case transfer size is not within the certain limits or fails to map DMA buffers but debug messages don't reveal that. Move these debug messages further in pump_transfers() where the actual transfer mode is known and use drv_data->dma_mapped flag instead of chip->enable_dma for printing the mode. Signed-off-by: Jarkko Nikula Signed-off-by: Mark Brown --- drivers/spi/spi-pxa2xx.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-) diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c index ab9914ad8365..227e8bad19e6 100644 --- a/drivers/spi/spi-pxa2xx.c +++ b/drivers/spi/spi-pxa2xx.c @@ -1001,19 +1001,6 @@ static void pump_transfers(unsigned long data) "pump_transfers: DMA burst size reduced to match bits_per_word\n"); } - /* NOTE: PXA25x_SSP _could_ use external clocking ... */ - cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits); - if (!pxa25x_ssp_comp(drv_data)) - dev_dbg(&message->spi->dev, "%u Hz actual, %s\n", - drv_data->master->max_speed_hz - / (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)), - chip->enable_dma ? "DMA" : "PIO"); - else - dev_dbg(&message->spi->dev, "%u Hz actual, %s\n", - drv_data->master->max_speed_hz / 2 - / (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)), - chip->enable_dma ? "DMA" : "PIO"); - message->state = RUNNING_STATE; drv_data->dma_mapped = 0; @@ -1040,6 +1027,19 @@ static void pump_transfers(unsigned long data) write_SSSR_CS(drv_data, drv_data->clear_sr); } + /* NOTE: PXA25x_SSP _could_ use external clocking ... */ + cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits); + if (!pxa25x_ssp_comp(drv_data)) + dev_dbg(&message->spi->dev, "%u Hz actual, %s\n", + drv_data->master->max_speed_hz + / (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)), + drv_data->dma_mapped ? "DMA" : "PIO"); + else + dev_dbg(&message->spi->dev, "%u Hz actual, %s\n", + drv_data->master->max_speed_hz / 2 + / (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)), + drv_data->dma_mapped ? "DMA" : "PIO"); + if (is_lpss_ssp(drv_data)) { if ((pxa2xx_spi_read(drv_data, SSIRF) & 0xff) != chip->lpss_rx_threshold) -- cgit v1.2.3