From 5e0fa3f63eda875cbe23be37d64a16c65a577209 Mon Sep 17 00:00:00 2001 From: Stanislav Brabec Date: Thu, 22 Oct 2009 23:05:03 +0200 Subject: [ARM] pxa/zaurus: fix NAND flash OOB layout for Borzoi Borzoi, Terrier and Akita use the same NAND Flash OOB layout, which seems to be different from Spitz for some reason. Here is a fix. When the code was ported to the platform data, the map was applied just for Akita. After this patch, Flash works again on Borzoi. Terrier still has a problem with partition table different from Borzoi (unfixable without reading of the system configuration in flash) and JFFS2 partitions can be mounted (with some "Empty flash at ... ends at ..." in the syslog). Signed-off-by: Stanislav Brabec Acked-by: Richard Purdie Signed-off-by: Eric Miao --- arch/arm/mach-pxa/spitz.c | 39 +++++++++++++++++++++++---------------- 1 file changed, 23 insertions(+), 16 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index 82ff5733e4dc..3da45d051743 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -779,11 +779,34 @@ static void __init common_init(void) pxa_set_i2c_info(NULL); } +#if defined(CONFIG_MACH_AKITA) || defined(CONFIG_MACH_BORZOI) +static struct nand_bbt_descr sharpsl_akita_bbt = { + .options = 0, + .offs = 4, + .len = 1, + .pattern = scan_ff_pattern +}; + +static struct nand_ecclayout akita_oobinfo = { + .eccbytes = 24, + .eccpos = { + 0x5, 0x1, 0x2, 0x3, 0x6, 0x7, 0x15, 0x11, + 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23, + 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37}, + .oobfree = {{0x08, 0x09}} +}; +#endif + #if defined(CONFIG_MACH_SPITZ) || defined(CONFIG_MACH_BORZOI) static void __init spitz_init(void) { spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON; + if (machine_is_borzoi()) { + sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt; + sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo; + } + platform_scoop_config = &spitz_pcmcia_config; common_init(); @@ -808,22 +831,6 @@ static struct i2c_board_info akita_i2c_board_info[] = { }, }; -static struct nand_bbt_descr sharpsl_akita_bbt = { - .options = 0, - .offs = 4, - .len = 1, - .pattern = scan_ff_pattern -}; - -static struct nand_ecclayout akita_oobinfo = { - .eccbytes = 24, - .eccpos = { - 0x5, 0x1, 0x2, 0x3, 0x6, 0x7, 0x15, 0x11, - 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23, - 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37}, - .oobfree = {{0x08, 0x09}} -}; - static void __init akita_init(void) { spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON; -- cgit v1.2.3 From 902805dbdae016653768f7139d7b3ab36a20cc6d Mon Sep 17 00:00:00 2001 From: Ondrej Zajicek Date: Mon, 26 Oct 2009 23:59:30 +0100 Subject: [ARM] pxa/palm: fix incorrect initialization of Palm Tungsten C keyboard Palm Tungsten C keyboard structure has swapped rows/cols gpio structures and does not work. This patch fixes it. Signed-off-by: Ondrej Zajicek Cc: Marek Vasut Signed-off-by: Eric Miao --- arch/arm/mach-pxa/palmtc.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c index bb2cc0dd44ec..0b92291a58f6 100644 --- a/arch/arm/mach-pxa/palmtc.c +++ b/arch/arm/mach-pxa/palmtc.c @@ -292,10 +292,10 @@ const static unsigned int palmtc_keypad_col_gpios[] = { static struct matrix_keypad_platform_data palmtc_keypad_platform_data = { .keymap_data = &palmtc_keymap_data, - .col_gpios = palmtc_keypad_row_gpios, - .num_col_gpios = 12, - .row_gpios = palmtc_keypad_col_gpios, - .num_row_gpios = 4, + .row_gpios = palmtc_keypad_row_gpios, + .num_row_gpios = ARRAY_SIZE(palmtc_keypad_row_gpios), + .col_gpios = palmtc_keypad_col_gpios, + .num_col_gpios = ARRAY_SIZE(palmtc_keypad_col_gpios), .active_low = 1, .debounce_ms = 20, -- cgit v1.2.3 From c482ae4dcf23fd241321595d71bbe8aee33eabf5 Mon Sep 17 00:00:00 2001 From: Haojian Zhuang Date: Mon, 2 Nov 2009 14:02:21 -0500 Subject: [ARM] pxa: fix resume failure by saving/restoring IPRx registers Since interrupt handler is changed to use interrupt priority, we also need to save and restore these interrupt controller registers in suspend/resume routine. Signed-off-by: Haojian Zhuang Tested-by: Daniel Mack Tested-by: Pavel Machek Tested-by: Robert Jarzmik Acked-by: Pavel Machek Signed-off-by: Eric Miao --- arch/arm/mach-pxa/irq.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c index d694ce289668..6112af431fa4 100644 --- a/arch/arm/mach-pxa/irq.c +++ b/arch/arm/mach-pxa/irq.c @@ -25,6 +25,8 @@ #include "generic.h" +#define MAX_INTERNAL_IRQS 128 + #define IRQ_BIT(n) (((n) - PXA_IRQ(0)) & 0x1f) #define _ICMR(n) (*((((n) - PXA_IRQ(0)) & ~0x1f) ? &ICMR2 : &ICMR)) #define _ICLR(n) (*((((n) - PXA_IRQ(0)) & ~0x1f) ? &ICLR2 : &ICLR)) @@ -122,6 +124,8 @@ void __init pxa_init_irq(int irq_nr, set_wake_t fn) { int irq, i; + BUG_ON(irq_nr > MAX_INTERNAL_IRQS); + pxa_internal_irq_nr = irq_nr; for (irq = PXA_IRQ(0); irq < PXA_IRQ(irq_nr); irq += 32) { @@ -149,7 +153,8 @@ void __init pxa_init_irq(int irq_nr, set_wake_t fn) } #ifdef CONFIG_PM -static unsigned long saved_icmr[2]; +static unsigned long saved_icmr[MAX_INTERNAL_IRQS/32]; +static unsigned long saved_ipr[MAX_INTERNAL_IRQS]; static int pxa_irq_suspend(struct sys_device *dev, pm_message_t state) { @@ -159,6 +164,8 @@ static int pxa_irq_suspend(struct sys_device *dev, pm_message_t state) saved_icmr[i] = _ICMR(irq); _ICMR(irq) = 0; } + for (i = 0; i < pxa_internal_irq_nr; i++) + saved_ipr[i] = IPR(i); return 0; } @@ -171,6 +178,8 @@ static int pxa_irq_resume(struct sys_device *dev) _ICMR(irq) = saved_icmr[i]; _ICLR(irq) = 0; } + for (i = 0; i < pxa_internal_irq_nr; i++) + IPR(i) = saved_ipr[i]; ICCR = 1; return 0; -- cgit v1.2.3 From 1b3a02eb452354fa9b36a7f33dc4c8307bbc40aa Mon Sep 17 00:00:00 2001 From: Tony Thompson Date: Wed, 4 Nov 2009 12:16:38 +0000 Subject: ARMv7: Check whether the SMP/nAMP mode was already enabled If running in non-secure mode, enabling this register will fault. Signed-off-by: Tony Thompson Acked-by: Srinidhi Kasagar Signed-off-by: Catalin Marinas --- arch/arm/mm/proc-v7.S | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S index eeeed01ee44a..3a285218fd15 100644 --- a/arch/arm/mm/proc-v7.S +++ b/arch/arm/mm/proc-v7.S @@ -186,9 +186,10 @@ cpu_v7_name: */ __v7_setup: #ifdef CONFIG_SMP - mrc p15, 0, r0, c1, c0, 1 @ Enable SMP/nAMP mode and - orr r0, r0, #(1 << 6) | (1 << 0) @ TLB ops broadcasting - mcr p15, 0, r0, c1, c0, 1 + mrc p15, 0, r0, c1, c0, 1 + tst r0, #(1 << 6) @ SMP/nAMP mode enabled? + orreq r0, r0, #(1 << 6) | (1 << 0) @ Enable SMP/nAMP mode and + mcreq p15, 0, r0, c1, c0, 1 @ TLB ops broadcasting #endif adr r12, __v7_setup_stack @ the local stack stmia r12, {r0-r5, r7, r9, r11, lr} -- cgit v1.2.3 From 9b229fa0951fb47cbc178be4bd8e9ef185b38802 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 4 Nov 2009 12:16:38 +0000 Subject: Check whether the SCU was already initialised If Linux is running in non-secure mode, this register may have been already initialised and writing to the control register not allowed. Signed-off-by: Catalin Marinas --- arch/arm/kernel/smp_scu.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/kernel/smp_scu.c b/arch/arm/kernel/smp_scu.c index d3831f616ee9..9ab4149bd983 100644 --- a/arch/arm/kernel/smp_scu.c +++ b/arch/arm/kernel/smp_scu.c @@ -37,6 +37,10 @@ void __init scu_enable(void __iomem *scu_base) u32 scu_ctrl; scu_ctrl = __raw_readl(scu_base + SCU_CTRL); + /* already enabled? */ + if (scu_ctrl & 1) + return; + scu_ctrl |= 1; __raw_writel(scu_ctrl, scu_base + SCU_CTRL); -- cgit v1.2.3 From 5b39d1548dc2751f8de89e6f429b6560a137eebb Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 4 Nov 2009 12:19:04 +0000 Subject: RealView: Add default memory configuration This patch adds a realview_fixup() function called during booting to set up the memory banks. This way there is no need to pass a "mem=" argument on the kernel command line. Signed-off-by: Catalin Marinas --- arch/arm/mach-realview/core.c | 21 +++++++++++++++++++++ arch/arm/mach-realview/core.h | 6 ++++++ arch/arm/mach-realview/realview_eb.c | 1 + arch/arm/mach-realview/realview_pb1176.c | 13 +++++++++++++ arch/arm/mach-realview/realview_pb11mp.c | 1 + arch/arm/mach-realview/realview_pba8.c | 1 + arch/arm/mach-realview/realview_pbx.c | 1 + 7 files changed, 44 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-realview/core.c b/arch/arm/mach-realview/core.c index a2083b60e3fb..c21b0fd39652 100644 --- a/arch/arm/mach-realview/core.c +++ b/arch/arm/mach-realview/core.c @@ -788,3 +788,24 @@ void __init realview_timer_init(unsigned int timer_irq) realview_clocksource_init(); realview_clockevents_init(timer_irq); } + +/* + * Setup the memory banks. + */ +void realview_fixup(struct machine_desc *mdesc, struct tag *tags, char **from, + struct meminfo *meminfo) +{ + /* + * Most RealView platforms have 512MB contiguous RAM at 0x70000000. + * Half of this is mirrored at 0. + */ +#ifdef CONFIG_REALVIEW_HIGH_PHYS_OFFSET + meminfo->bank[0].start = 0x70000000; + meminfo->bank[0].size = SZ_512M; + meminfo->nr_banks = 1; +#else + meminfo->bank[0].start = 0; + meminfo->bank[0].size = SZ_256M; + meminfo->nr_banks = 1; +#endif +} diff --git a/arch/arm/mach-realview/core.h b/arch/arm/mach-realview/core.h index 699671fa6e0b..781bca68a9fa 100644 --- a/arch/arm/mach-realview/core.h +++ b/arch/arm/mach-realview/core.h @@ -25,6 +25,7 @@ #include #include +#include #include #define AMBA_DEVICE(name,busid,base,plat) \ @@ -44,6 +45,8 @@ static struct amba_device name##_device = { \ /* .dma = base##_DMA,*/ \ } +struct machine_desc; + extern struct platform_device realview_flash_device; extern struct platform_device realview_cf_device; extern struct platform_device realview_i2c_device; @@ -61,5 +64,8 @@ extern void realview_timer_init(unsigned int timer_irq); extern int realview_flash_register(struct resource *res, u32 num); extern int realview_eth_register(const char *name, struct resource *res); extern int realview_usb_register(struct resource *res); +extern void realview_fixup(struct machine_desc *mdesc, struct tag *tags, + char **from, struct meminfo *meminfo); extern void (*realview_reset)(char); + #endif diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index 1d65e64ae571..917f8ca3abff 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -415,6 +415,7 @@ MACHINE_START(REALVIEW_EB, "ARM-RealView EB") .phys_io = REALVIEW_EB_UART0_BASE, .io_pg_offst = (IO_ADDRESS(REALVIEW_EB_UART0_BASE) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x00000100, + .fixup = realview_fixup, .map_io = realview_eb_map_io, .init_irq = gic_init_irq, .timer = &realview_eb_timer, diff --git a/arch/arm/mach-realview/realview_pb1176.c b/arch/arm/mach-realview/realview_pb1176.c index a6ba147692c1..7fb726d5f8b9 100644 --- a/arch/arm/mach-realview/realview_pb1176.c +++ b/arch/arm/mach-realview/realview_pb1176.c @@ -300,6 +300,18 @@ static void realview_pb1176_reset(char mode) __raw_writel(REALVIEW_PB1176_SYS_LOCKVAL_RSTCTL, hdr_ctrl); } +static void realview_pb1176_fixup(struct machine_desc *mdesc, + struct tag *tags, char **from, + struct meminfo *meminfo) +{ + /* + * RealView PB1176 only has 128MB of RAM mapped at 0. + */ + meminfo->bank[0].start = 0; + meminfo->bank[0].size = SZ_128M; + meminfo->nr_banks = 1; +} + static void __init realview_pb1176_init(void) { int i; @@ -331,6 +343,7 @@ MACHINE_START(REALVIEW_PB1176, "ARM-RealView PB1176") .phys_io = REALVIEW_PB1176_UART0_BASE, .io_pg_offst = (IO_ADDRESS(REALVIEW_PB1176_UART0_BASE) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x00000100, + .fixup = realview_pb1176_fixup, .map_io = realview_pb1176_map_io, .init_irq = gic_init_irq, .timer = &realview_pb1176_timer, diff --git a/arch/arm/mach-realview/realview_pb11mp.c b/arch/arm/mach-realview/realview_pb11mp.c index 070d284ce96e..9bbbfc05f225 100644 --- a/arch/arm/mach-realview/realview_pb11mp.c +++ b/arch/arm/mach-realview/realview_pb11mp.c @@ -347,6 +347,7 @@ MACHINE_START(REALVIEW_PB11MP, "ARM-RealView PB11MPCore") .phys_io = REALVIEW_PB11MP_UART0_BASE, .io_pg_offst = (IO_ADDRESS(REALVIEW_PB11MP_UART0_BASE) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x00000100, + .fixup = realview_fixup, .map_io = realview_pb11mp_map_io, .init_irq = gic_init_irq, .timer = &realview_pb11mp_timer, diff --git a/arch/arm/mach-realview/realview_pba8.c b/arch/arm/mach-realview/realview_pba8.c index 941beb2b9709..fe861e96c566 100644 --- a/arch/arm/mach-realview/realview_pba8.c +++ b/arch/arm/mach-realview/realview_pba8.c @@ -298,6 +298,7 @@ MACHINE_START(REALVIEW_PBA8, "ARM-RealView PB-A8") .phys_io = REALVIEW_PBA8_UART0_BASE, .io_pg_offst = (IO_ADDRESS(REALVIEW_PBA8_UART0_BASE) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x00000100, + .fixup = realview_fixup, .map_io = realview_pba8_map_io, .init_irq = gic_init_irq, .timer = &realview_pba8_timer, diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c index 7e4bc6cdca52..5d09d8b4a1cb 100644 --- a/arch/arm/mach-realview/realview_pbx.c +++ b/arch/arm/mach-realview/realview_pbx.c @@ -345,6 +345,7 @@ MACHINE_START(REALVIEW_PBX, "ARM-RealView PBX") .phys_io = REALVIEW_PBX_UART0_BASE, .io_pg_offst = (IO_ADDRESS(REALVIEW_PBX_UART0_BASE) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x00000100, + .fixup = realview_fixup, .map_io = realview_pbx_map_io, .init_irq = gic_init_irq, .timer = &realview_pbx_timer, -- cgit v1.2.3 From 157aed7473d300587e89cc87e13f194e3fa6fa36 Mon Sep 17 00:00:00 2001 From: Colin Tuckley Date: Wed, 4 Nov 2009 12:19:05 +0000 Subject: RealView: Remove duplicated #define REALVIEW_SYS_FLAGS* statements The platsmp.c file defines the REALVIEW_SYS_FLAGS* macros which are already present in platform.h. Just use the latter. Signed-off-by: Colin Tuckley Signed-off-by: Catalin Marinas --- arch/arm/mach-realview/platsmp.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-realview/platsmp.c b/arch/arm/mach-realview/platsmp.c index a88458b4799d..009265818d55 100644 --- a/arch/arm/mach-realview/platsmp.c +++ b/arch/arm/mach-realview/platsmp.c @@ -146,11 +146,8 @@ static void __init poke_milo(void) * register. The BootMonitor waits for this register to become * non-zero. */ -#define REALVIEW_SYS_FLAGSS_OFFSET 0x30 -#define REALVIEW_SYS_FLAGSC_OFFSET 0x34 __raw_writel(BSYM(virt_to_phys(realview_secondary_startup)), - __io_address(REALVIEW_SYS_BASE) + - REALVIEW_SYS_FLAGSS_OFFSET); + __io_address(REALVIEW_SYS_FLAGSSET)); mb(); } -- cgit v1.2.3 From c97c5aa83c41a532bc67da356d77da929bc41b9c Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 4 Nov 2009 12:19:05 +0000 Subject: RealView: Add sparsemem support for the RealView PBX platform The RealView PBX board has two 512MB blocks of memory - one at 0x70000000 (with 256MB mirror at 0) and another at 0x20000000. Only the block at 0x70000000 (or the mirror at 0) may be used for DMA (e.g. framebuffer). This patch adds the sparsemem definitions to allow the use of all the memory split as follows: 256MB @ 0x00000000 (ZONE_DMA) 512MB @ 0x20000000 (ZONE_NORMAL) 256MB @ 0x80000000 (ZONE_NORMAL) Signed-off-by: Catalin Marinas --- arch/arm/mach-realview/Kconfig | 5 ++- arch/arm/mach-realview/core.c | 21 +++++++++++- arch/arm/mach-realview/include/mach/memory.h | 49 ++++++++++++++++++++++++++++ arch/arm/mach-realview/realview_pbx.c | 22 ++++++++++++- 4 files changed, 94 insertions(+), 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-realview/Kconfig b/arch/arm/mach-realview/Kconfig index dfc9b0bc6eb2..c48e1f2c3349 100644 --- a/arch/arm/mach-realview/Kconfig +++ b/arch/arm/mach-realview/Kconfig @@ -70,6 +70,8 @@ config MACH_REALVIEW_PBX bool "Support RealView/PBX platform" select ARM_GIC select HAVE_PATA_PLATFORM + select ARCH_SPARSEMEM_ENABLE if CPU_V7 && !HIGH_PHYS_OFFSET + select ZONE_DMA if SPARSEMEM help Include support for the ARM(R) RealView PBX platform. @@ -82,6 +84,7 @@ config REALVIEW_HIGH_PHYS_OFFSET 0x70000000, 256MB of which being mirrored at 0x00000000. If the board supports 512MB of RAM, this option allows the memory to be accessed contiguously at the high physical - offset. + offset. On the PBX board, disabling this option allows 1GB of + RAM to be used with SPARSEMEM. endmenu diff --git a/arch/arm/mach-realview/core.c b/arch/arm/mach-realview/core.c index c21b0fd39652..9f293438e020 100644 --- a/arch/arm/mach-realview/core.c +++ b/arch/arm/mach-realview/core.c @@ -59,6 +59,25 @@ /* used by entry-macro.S and platsmp.c */ void __iomem *gic_cpu_base_addr; +#ifdef CONFIG_ZONE_DMA +/* + * Adjust the zones if there are restrictions for DMA access. + */ +void __init realview_adjust_zones(int node, unsigned long *size, + unsigned long *hole) +{ + unsigned long dma_size = SZ_256M >> PAGE_SHIFT; + + if (!machine_is_realview_pbx() || node || (size[0] <= dma_size)) + return; + + size[ZONE_NORMAL] = size[0] - dma_size; + size[ZONE_DMA] = dma_size; + hole[ZONE_NORMAL] = hole[0]; + hole[ZONE_DMA] = 0; +} +#endif + /* * This is the RealView sched_clock implementation. This has * a resolution of 41.7ns, and a maximum value of about 179s. @@ -543,7 +562,7 @@ static int realview_clcd_setup(struct clcd_fb *fb) fb->panel = realview_clcd_panel(); fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, framesize, - &dma, GFP_KERNEL); + &dma, GFP_KERNEL | GFP_DMA); if (!fb->fb.screen_base) { printk(KERN_ERR "CLCD: unable to map framebuffer\n"); return -ENOMEM; diff --git a/arch/arm/mach-realview/include/mach/memory.h b/arch/arm/mach-realview/include/mach/memory.h index 293c30025e7e..2417bbcf97fd 100644 --- a/arch/arm/mach-realview/include/mach/memory.h +++ b/arch/arm/mach-realview/include/mach/memory.h @@ -29,4 +29,53 @@ #define PHYS_OFFSET UL(0x00000000) #endif +#if !defined(__ASSEMBLY__) && defined(CONFIG_ZONE_DMA) +extern void realview_adjust_zones(int node, unsigned long *size, + unsigned long *hole); +#define arch_adjust_zones(node, size, hole) \ + realview_adjust_zones(node, size, hole) + +#define ISA_DMA_THRESHOLD (PHYS_OFFSET + SZ_256M - 1) +#define MAX_DMA_ADDRESS (PAGE_OFFSET + SZ_256M) +#endif + +#ifdef CONFIG_SPARSEMEM + +/* + * Sparsemem definitions for RealView PBX. + * + * The RealView PBX board has another block of 512MB of RAM at 0x20000000, + * however only the block at 0x70000000 (or the 256MB mirror at 0x00000000) + * may be used for DMA. + * + * The macros below define a section size of 256MB and a non-linear virtual to + * physical mapping: + * + * 256MB @ 0x00000000 -> PAGE_OFFSET + * 512MB @ 0x20000000 -> PAGE_OFFSET + 0x10000000 + * 256MB @ 0x80000000 -> PAGE_OFFSET + 0x30000000 + */ +#ifdef CONFIG_REALVIEW_HIGH_PHYS_OFFSET +#error "SPARSEMEM not available with REALVIEW_HIGH_PHYS_OFFSET" +#endif + +#define MAX_PHYSMEM_BITS 32 +#define SECTION_SIZE_BITS 28 + +/* bank page offsets */ +#define PAGE_OFFSET1 (PAGE_OFFSET + 0x10000000) +#define PAGE_OFFSET2 (PAGE_OFFSET + 0x30000000) + +#define __phys_to_virt(phys) \ + ((phys) >= 0x80000000 ? (phys) - 0x80000000 + PAGE_OFFSET2 : \ + (phys) >= 0x20000000 ? (phys) - 0x20000000 + PAGE_OFFSET1 : \ + (phys) + PAGE_OFFSET) + +#define __virt_to_phys(virt) \ + ((virt) >= PAGE_OFFSET2 ? (virt) - PAGE_OFFSET2 + 0x80000000 : \ + (virt) >= PAGE_OFFSET1 ? (virt) - PAGE_OFFSET1 + 0x20000000 : \ + (virt) - PAGE_OFFSET) + +#endif /* CONFIG_SPARSEMEM */ + #endif diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c index 5d09d8b4a1cb..ec39488e2b42 100644 --- a/arch/arm/mach-realview/realview_pbx.c +++ b/arch/arm/mach-realview/realview_pbx.c @@ -304,6 +304,26 @@ static struct sys_timer realview_pbx_timer = { .init = realview_pbx_timer_init, }; +static void realview_pbx_fixup(struct machine_desc *mdesc, struct tag *tags, + char **from, struct meminfo *meminfo) +{ +#ifdef CONFIG_SPARSEMEM + /* + * Memory configuration with SPARSEMEM enabled on RealView PBX (see + * asm/mach/memory.h for more information). + */ + meminfo->bank[0].start = 0; + meminfo->bank[0].size = SZ_256M; + meminfo->bank[1].start = 0x20000000; + meminfo->bank[1].size = SZ_512M; + meminfo->bank[2].start = 0x80000000; + meminfo->bank[2].size = SZ_256M; + meminfo->nr_banks = 3; +#else + realview_fixup(mdesc, tags, from, meminfo); +#endif +} + static void __init realview_pbx_init(void) { int i; @@ -345,7 +365,7 @@ MACHINE_START(REALVIEW_PBX, "ARM-RealView PBX") .phys_io = REALVIEW_PBX_UART0_BASE, .io_pg_offst = (IO_ADDRESS(REALVIEW_PBX_UART0_BASE) >> 18) & 0xfffc, .boot_params = PHYS_OFFSET + 0x00000100, - .fixup = realview_fixup, + .fixup = realview_pbx_fixup, .map_io = realview_pbx_map_io, .init_irq = gic_init_irq, .timer = &realview_pbx_timer, -- cgit v1.2.3 From d525753bf30fe29a2897273e180fc24723350dcc Mon Sep 17 00:00:00 2001 From: Jean-Christop PLAGNIOL-VILLARD Date: Mon, 2 Nov 2009 20:13:32 +0100 Subject: ARM: 5779/1: ep93xx/micro9.c: fix implicit declaration of function __raw_readl and IOMEM Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: H Hartley Sweeten Signed-off-by: Russell King --- arch/arm/mach-ep93xx/micro9.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-ep93xx/micro9.c b/arch/arm/mach-ep93xx/micro9.c index d83b80478b09..f3757a1c5a10 100644 --- a/arch/arm/mach-ep93xx/micro9.c +++ b/arch/arm/mach-ep93xx/micro9.c @@ -15,6 +15,7 @@ #include #include #include +#include #include -- cgit v1.2.3 From c742239866250a5690485ab775b942c85c6bee63 Mon Sep 17 00:00:00 2001 From: zeal Date: Tue, 3 Nov 2009 02:36:55 +0100 Subject: ARM: 5780/1: KS8695: Fix macro definition bug in regs-switch.c NOTE: 1. Macro style is so strange. 2. The value 0xc0 is not match with KS8695 manual. It should be 0x0c. Signed-off-by: zeal Acked-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-ks8695/include/mach/regs-switch.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-ks8695/include/mach/regs-switch.h b/arch/arm/mach-ks8695/include/mach/regs-switch.h index 56d12e8de895..97e8acb1cf6c 100644 --- a/arch/arm/mach-ks8695/include/mach/regs-switch.h +++ b/arch/arm/mach-ks8695/include/mach/regs-switch.h @@ -25,7 +25,7 @@ #define KS8695_SEC1 (0x04) /* Switch Engine Control 1 */ #define KS8695_SEC2 (0x08) /* Switch Engine Control 2 */ -#define KS8695_P(x)_C(z) (0xc0 + (((x)-1)*3 + ((z)-1))*4) /* Port Configuration Registers */ +#define KS8695_SEPXCZ(x,z) (0x0c + (((x)-1)*3 + ((z)-1))*4) /* Port Configuration Registers */ #define KS8695_SEP12AN (0x48) /* Port 1 & 2 Auto-Negotiation */ #define KS8695_SEP34AN (0x4c) /* Port 3 & 4 Auto-Negotiation */ -- cgit v1.2.3 From 662aeced1512e008e5613b91de8e8b8e01017cb5 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Wed, 30 Sep 2009 13:02:42 -0700 Subject: [ARM] properly report mv78100 stepping A1 Signed-off-by: Lennert Buytenhek Signed-off-by: Nicolas Pitre --- arch/arm/mach-mv78xx0/common.c | 2 ++ arch/arm/mach-mv78xx0/include/mach/mv78xx0.h | 1 + 2 files changed, 3 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-mv78xx0/common.c b/arch/arm/mach-mv78xx0/common.c index 1b22e4af8791..08465eb6a2c2 100644 --- a/arch/arm/mach-mv78xx0/common.c +++ b/arch/arm/mach-mv78xx0/common.c @@ -845,6 +845,8 @@ static char * __init mv78xx0_id(void) } else if (dev == MV78100_DEV_ID) { if (rev == MV78100_REV_A0) return "MV78100-A0"; + else if (rev == MV78100_REV_A1) + return "MV78100-A1"; else return "MV78100-Rev-Unsupported"; } else if (dev == MV78200_DEV_ID) { diff --git a/arch/arm/mach-mv78xx0/include/mach/mv78xx0.h b/arch/arm/mach-mv78xx0/include/mach/mv78xx0.h index d715b92b0908..788bdace1304 100644 --- a/arch/arm/mach-mv78xx0/include/mach/mv78xx0.h +++ b/arch/arm/mach-mv78xx0/include/mach/mv78xx0.h @@ -112,6 +112,7 @@ #define MV78100_DEV_ID 0x7810 #define MV78100_REV_A0 1 +#define MV78100_REV_A1 2 #define MV78200_DEV_ID 0x7820 #define MV78200_REV_A0 1 -- cgit v1.2.3 From 5d8965557318fabb1680d1817c2afc2714b6d3ce Mon Sep 17 00:00:00 2001 From: Simon Kagstrom Date: Fri, 9 Oct 2009 08:26:45 +0200 Subject: [ARM] OpenRD base: Initialize PCI express and i2c Signed-off-by: Simon Kagstrom Acked-by: Dieter Kiermaier Signed-off-by: Nicolas Pitre --- arch/arm/mach-kirkwood/openrd_base-setup.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-kirkwood/openrd_base-setup.c b/arch/arm/mach-kirkwood/openrd_base-setup.c index 947dfb8cd5b2..77617c722299 100644 --- a/arch/arm/mach-kirkwood/openrd_base-setup.c +++ b/arch/arm/mach-kirkwood/openrd_base-setup.c @@ -70,8 +70,20 @@ static void __init openrd_base_init(void) kirkwood_ge00_init(&openrd_base_ge00_data); kirkwood_sata_init(&openrd_base_sata_data); kirkwood_sdio_init(&openrd_base_mvsdio_data); + + kirkwood_i2c_init(); } +static int __init openrd_base_pci_init(void) +{ + if (machine_is_openrd_base()) + kirkwood_pcie_init(); + + return 0; + } +subsys_initcall(openrd_base_pci_init); + + MACHINE_START(OPENRD_BASE, "Marvell OpenRD Base Board") /* Maintainer: Dhaval Vasa */ .phys_io = KIRKWOOD_REGS_PHYS_BASE, -- cgit v1.2.3 From 6de95c198729d34a85c88f8844f1c3d57fb6da00 Mon Sep 17 00:00:00 2001 From: Li Jie Date: Thu, 5 Nov 2009 07:29:54 -0800 Subject: [ARM] kirkwood: fix section mismatch kirkwood_timer_init() and kirkwood_pcie_setup() lack of __init which causes following warnings: WARNING: vmlinux.o(.text+0x9568): Section mismatch in reference from the function kirkwood_timer_init() to the function .init.text:kirkwood_find_tclk() The function kirkwood_timer_init() references the function __init kirkwood_find_tclk(). This is often because kirkwood_timer_init lacks a __init annotation or the annotation of kirkwood_find_tclk is wrong. WARNING: vmlinux.o(.text+0x979c): Section mismatch in reference from the function kirkwood_pcie_setup() to the function .init.text:orion_pcie_setup() The function kirkwood_pcie_setup() references the function __init orion_pcie_setup(). This is often because kirkwood_pcie_setup lacks a __init annotation or the annotation of orion_pcie_setup is wrong. Signed-off-by: lijie Signed-off-by: Nicolas Pitre --- arch/arm/mach-kirkwood/common.c | 2 +- arch/arm/mach-kirkwood/pcie.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c index 0acb61f3c10b..7177c4aa6342 100644 --- a/arch/arm/mach-kirkwood/common.c +++ b/arch/arm/mach-kirkwood/common.c @@ -845,7 +845,7 @@ int __init kirkwood_find_tclk(void) return 166666667; } -static void kirkwood_timer_init(void) +static void __init kirkwood_timer_init(void) { kirkwood_tclk = kirkwood_find_tclk(); orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk); diff --git a/arch/arm/mach-kirkwood/pcie.c b/arch/arm/mach-kirkwood/pcie.c index d90b9aae308d..553882033006 100644 --- a/arch/arm/mach-kirkwood/pcie.c +++ b/arch/arm/mach-kirkwood/pcie.c @@ -93,7 +93,7 @@ static struct pci_ops pcie_ops = { }; -static int kirkwood_pcie_setup(int nr, struct pci_sys_data *sys) +static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys) { struct resource *res; extern unsigned int kirkwood_clk_ctrl; -- cgit v1.2.3 From 35f029e2514be209eb0e88c7d927f3bcc42a5cc2 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sat, 7 Nov 2009 14:49:18 +0100 Subject: [ARM] kirkwood: fix PCI I/O port assignment Instead of allocating PCI devices I/O port bus addresses from the 000xxxxx I/O port range as intended, due to a bus versus physical address mixup, the Kirkwood PCIe handling code inadvertently allocated I/O port bus addresses from the f20xxxxx address range (which is the physical address range of the PCIe I/O mapping window), but then direct all I/O port accesses to bus addresses 000xxxxx, which would then not be decoded at all. Fix this by setting the base address of the PCIe I/O space struct resource to KIRKWOOD_PCIE_IO_BUS_BASE instead of the incorrect KIRKWOOD_PCIE_IO_PHYS_BASE, and fix up __io() to expect addresses offsetted by the former instead of the latter. (The suggested fix of directing I/O port accesses from the host to bus addresses f20xxxxx instead has the problem that assigning full 32bit I/O port bus addresses (f20xxxxx) doesn't work on all PCI devices, as not all PCI devices implement full 32 bit BAR registers for I/O ports. We should really try to allocate I/O port bus addresses that fit in 16 bits.) Signed-off-by: Lennert Buytenhek Signed-off-by: Nicolas Pitre --- arch/arm/mach-kirkwood/include/mach/io.h | 2 +- arch/arm/mach-kirkwood/pcie.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-kirkwood/include/mach/io.h b/arch/arm/mach-kirkwood/include/mach/io.h index a643a846d5fb..44e8be04f259 100644 --- a/arch/arm/mach-kirkwood/include/mach/io.h +++ b/arch/arm/mach-kirkwood/include/mach/io.h @@ -15,7 +15,7 @@ static inline void __iomem *__io(unsigned long addr) { - return (void __iomem *)((addr - KIRKWOOD_PCIE_IO_PHYS_BASE) + return (void __iomem *)((addr - KIRKWOOD_PCIE_IO_BUS_BASE) + KIRKWOOD_PCIE_IO_VIRT_BASE); } diff --git a/arch/arm/mach-kirkwood/pcie.c b/arch/arm/mach-kirkwood/pcie.c index 553882033006..0660e78641e8 100644 --- a/arch/arm/mach-kirkwood/pcie.c +++ b/arch/arm/mach-kirkwood/pcie.c @@ -115,7 +115,7 @@ static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys) */ res[0].name = "PCIe I/O Space"; res[0].flags = IORESOURCE_IO; - res[0].start = KIRKWOOD_PCIE_IO_PHYS_BASE; + res[0].start = KIRKWOOD_PCIE_IO_BUS_BASE; res[0].end = res[0].start + KIRKWOOD_PCIE_IO_SIZE - 1; if (request_resource(&ioport_resource, &res[0])) panic("Request PCIe IO resource failed\n"); -- cgit v1.2.3 From a1897fa67cb964cc6b5a9048a31eb6ef3dcc2dda Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Sat, 7 Nov 2009 14:50:00 +0100 Subject: [ARM] Kirkwood: clarify PCIe MEM bus/physical address distinction Signed-off-by: Lennert Buytenhek Signed-off-by: Nicolas Pitre --- arch/arm/mach-kirkwood/addr-map.c | 2 +- arch/arm/mach-kirkwood/include/mach/kirkwood.h | 1 + arch/arm/mach-kirkwood/pcie.c | 2 +- 3 files changed, 3 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-kirkwood/addr-map.c b/arch/arm/mach-kirkwood/addr-map.c index 1da5d1c18ecb..2e69168fc699 100644 --- a/arch/arm/mach-kirkwood/addr-map.c +++ b/arch/arm/mach-kirkwood/addr-map.c @@ -105,7 +105,7 @@ void __init kirkwood_setup_cpu_mbus(void) setup_cpu_win(0, KIRKWOOD_PCIE_IO_PHYS_BASE, KIRKWOOD_PCIE_IO_SIZE, TARGET_PCIE, ATTR_PCIE_IO, KIRKWOOD_PCIE_IO_BUS_BASE); setup_cpu_win(1, KIRKWOOD_PCIE_MEM_PHYS_BASE, KIRKWOOD_PCIE_MEM_SIZE, - TARGET_PCIE, ATTR_PCIE_MEM, -1); + TARGET_PCIE, ATTR_PCIE_MEM, KIRKWOOD_PCIE_MEM_BUS_BASE); /* * Setup window for NAND controller. diff --git a/arch/arm/mach-kirkwood/include/mach/kirkwood.h b/arch/arm/mach-kirkwood/include/mach/kirkwood.h index 54c132731d2d..a15cf0ee22bd 100644 --- a/arch/arm/mach-kirkwood/include/mach/kirkwood.h +++ b/arch/arm/mach-kirkwood/include/mach/kirkwood.h @@ -43,6 +43,7 @@ #define KIRKWOOD_REGS_SIZE SZ_1M #define KIRKWOOD_PCIE_MEM_PHYS_BASE 0xe0000000 +#define KIRKWOOD_PCIE_MEM_BUS_BASE 0xe0000000 #define KIRKWOOD_PCIE_MEM_SIZE SZ_128M /* diff --git a/arch/arm/mach-kirkwood/pcie.c b/arch/arm/mach-kirkwood/pcie.c index 0660e78641e8..a604b2a701aa 100644 --- a/arch/arm/mach-kirkwood/pcie.c +++ b/arch/arm/mach-kirkwood/pcie.c @@ -126,7 +126,7 @@ static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys) */ res[1].name = "PCIe Memory Space"; res[1].flags = IORESOURCE_MEM; - res[1].start = KIRKWOOD_PCIE_MEM_PHYS_BASE; + res[1].start = KIRKWOOD_PCIE_MEM_BUS_BASE; res[1].end = res[1].start + KIRKWOOD_PCIE_MEM_SIZE - 1; if (request_resource(&iomem_resource, &res[1])) panic("Request PCIe Memory resource failed\n"); -- cgit v1.2.3 From ffbfe093b660ce1c9ede569ebe4f969f9003aa59 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Sat, 7 Nov 2009 20:36:02 -0500 Subject: [ARM] Kirkwood: update defconfig Signed-off-by: Nicolas Pitre --- arch/arm/configs/kirkwood_defconfig | 260 +++++++++++++++++++++++------------- 1 file changed, 169 insertions(+), 91 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig index af74cc2de8b6..bcfade33bca9 100644 --- a/arch/arm/configs/kirkwood_defconfig +++ b/arch/arm/configs/kirkwood_defconfig @@ -1,15 +1,13 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc4 -# Mon May 4 11:58:57 2009 +# Linux kernel version: 2.6.32-rc6 +# Sat Nov 7 20:31:18 2009 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_MMU=y -# CONFIG_NO_IOPORT is not set CONFIG_GENERIC_HARDIRQS=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y @@ -18,13 +16,12 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -46,11 +43,12 @@ CONFIG_SYSVIPC_SYSCTL=y # # RCU Subsystem # -CONFIG_CLASSIC_RCU=y -# CONFIG_TREE_RCU is not set -# CONFIG_PREEMPT_RCU is not set +CONFIG_TREE_RCU=y +# CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_RCU_TRACE is not set +CONFIG_RCU_FANOUT=32 +# CONFIG_RCU_FANOUT_EXACT is not set # CONFIG_TREE_RCU_TRACE is not set -# CONFIG_PREEMPT_RCU_TRACE is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=19 # CONFIG_GROUP_SCHED is not set @@ -73,7 +71,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -86,6 +83,10 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y + +# +# Kernel Performance Events And Counters +# CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y @@ -95,13 +96,17 @@ CONFIG_SLUB=y # CONFIG_SLOB is not set CONFIG_PROFILING=y CONFIG_TRACEPOINTS=y -# CONFIG_MARKERS is not set CONFIG_OPROFILE=y CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y CONFIG_KRETPROBES=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_SLABINFO=y @@ -114,7 +119,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -135,19 +140,22 @@ CONFIG_DEFAULT_IOSCHED="cfq" # # System Type # +CONFIG_MMU=y # CONFIG_ARCH_AAEC2000 is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_REALVIEW is not set # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_AT91 is not set # CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set -# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_NOMADIK is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set @@ -156,25 +164,27 @@ CONFIG_DEFAULT_IOSCHED="cfq" # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set CONFIG_ARCH_KIRKWOOD=y -# CONFIG_ARCH_KS8695 is not set -# CONFIG_ARCH_NS9XXX is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set -# CONFIG_ARCH_MXC is not set # CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set -# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_MSM is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5PC1XX is not set # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_MSM is not set -# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_BCMRING is not set # # Marvell Kirkwood Implementations @@ -185,6 +195,7 @@ CONFIG_MACH_RD88F6281=y CONFIG_MACH_MV88F6281GTW_GE=y CONFIG_MACH_SHEEVAPLUG=y CONFIG_MACH_TS219=y +CONFIG_MACH_OPENRD_BASE=y CONFIG_PLAT_ORION=y # @@ -195,7 +206,7 @@ CONFIG_CPU_FEROCEON=y # CONFIG_CPU_FEROCEON_OLD_ID is not set CONFIG_CPU_32v5=y CONFIG_CPU_ABRT_EV5T=y -CONFIG_CPU_PABRT_NOIFAR=y +CONFIG_CPU_PABRT_LEGACY=y CONFIG_CPU_CACHE_VIVT=y CONFIG_CPU_COPY_FEROCEON=y CONFIG_CPU_TLB_FEROCEON=y @@ -211,6 +222,7 @@ CONFIG_ARM_THUMB=y CONFIG_OUTER_CACHE=y CONFIG_CACHE_FEROCEON_L2=y # CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set +CONFIG_ARM_L1_CACHE_SHIFT=5 # # Bus support @@ -235,11 +247,12 @@ CONFIG_VMSPLIT_3G=y # CONFIG_VMSPLIT_2G is not set # CONFIG_VMSPLIT_1G is not set CONFIG_PAGE_OFFSET=0xC0000000 +# CONFIG_PREEMPT_NONE is not set +# CONFIG_PREEMPT_VOLUNTARY is not set CONFIG_PREEMPT=y CONFIG_HZ=100 CONFIG_AEABI=y # CONFIG_OABI_COMPAT is not set -CONFIG_ARCH_FLATMEM_HAS_HOLES=y # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set # CONFIG_HIGHMEM is not set @@ -254,10 +267,12 @@ CONFIG_SPLIT_PTLOCK_CPUS=4096 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_ALIGNMENT_TRAP=y +CONFIG_UACCESS_WITH_MEMCPY=y # # Boot options @@ -345,6 +360,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set # CONFIG_IP_SCTP is not set +# CONFIG_RDS is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set @@ -367,6 +383,7 @@ CONFIG_NET_DSA_MV88E6123_61_65=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -383,17 +400,18 @@ CONFIG_NET_PKTGEN=m # CONFIG_AF_RXRPC is not set CONFIG_WIRELESS=y CONFIG_CFG80211=y +# CONFIG_NL80211_TESTMODE is not set +# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set # CONFIG_CFG80211_REG_DEBUG is not set +CONFIG_CFG80211_DEFAULT_PS=y +CONFIG_CFG80211_DEFAULT_PS_VALUE=1 +# CONFIG_CFG80211_DEBUGFS is not set CONFIG_WIRELESS_OLD_REGULATORY=y CONFIG_WIRELESS_EXT=y CONFIG_WIRELESS_EXT_SYSFS=y CONFIG_LIB80211=y # CONFIG_LIB80211_DEBUG is not set CONFIG_MAC80211=y - -# -# Rate control algorithm selection -# CONFIG_MAC80211_RC_MINSTREL=y # CONFIG_MAC80211_RC_DEFAULT_PID is not set CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y @@ -414,6 +432,7 @@ CONFIG_MAC80211_RC_DEFAULT="minstrel" # Generic Driver Options # CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -425,9 +444,9 @@ CONFIG_EXTRA_FIRMWARE="" # CONFIG_CONNECTOR is not set CONFIG_MTD=y # CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_TESTS is not set # CONFIG_MTD_CONCAT is not set CONFIG_MTD_PARTITIONS=y -# CONFIG_MTD_TESTS is not set # CONFIG_MTD_REDBOOT_PARTS is not set CONFIG_MTD_CMDLINE_PARTS=y # CONFIG_MTD_AFS_PARTS is not set @@ -494,6 +513,7 @@ CONFIG_MTD_PHYSMAP=y # CONFIG_MTD_DATAFLASH is not set CONFIG_MTD_M25P80=y CONFIG_M25PXX_USE_FAST_READ=y +# CONFIG_MTD_SST25L is not set # CONFIG_MTD_SLRAM is not set # CONFIG_MTD_PHRAM is not set # CONFIG_MTD_MTDRAM is not set @@ -543,6 +563,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_RAM is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_MG_DISK is not set # CONFIG_MISC_DEVICES is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -567,10 +588,6 @@ CONFIG_BLK_DEV_SR=m # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -587,6 +604,8 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set +# CONFIG_BE2ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -595,6 +614,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -611,7 +631,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -623,11 +642,14 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_PMCRAID is not set # CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_BFA_FC is not set # CONFIG_SCSI_DH is not set # CONFIG_SCSI_OSD_INITIATOR is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set +CONFIG_ATA_VERBOSE_ERROR=y CONFIG_SATA_PMP=y CONFIG_SATA_AHCI=y # CONFIG_SATA_SIL24 is not set @@ -649,6 +671,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_ALI is not set # CONFIG_PATA_AMD is not set # CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATP867X is not set # CONFIG_PATA_ATIIXP is not set # CONFIG_PATA_CMD640_PCI is not set # CONFIG_PATA_CMD64X is not set @@ -676,6 +699,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set # CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RDC is not set # CONFIG_PATA_RZ1000 is not set # CONFIG_PATA_SC1200 is not set # CONFIG_PATA_SERVERWORKS is not set @@ -693,13 +717,16 @@ CONFIG_SATA_MV=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -768,6 +795,9 @@ CONFIG_NET_PCI=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set +# CONFIG_KS8851_MLL is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -789,6 +819,7 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_MV643XX_ETH=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set @@ -797,10 +828,7 @@ CONFIG_MV643XX_ETH=y # CONFIG_JME is not set # CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set - -# -# Wireless LAN -# +CONFIG_WLAN=y # CONFIG_WLAN_PRE80211 is not set CONFIG_WLAN_80211=y CONFIG_LIBERTAS=y @@ -820,9 +848,7 @@ CONFIG_LIBERTAS_SDIO=y # CONFIG_MAC80211_HWSIM is not set # CONFIG_MWL8K is not set # CONFIG_P54_COMMON is not set -# CONFIG_ATH5K is not set -# CONFIG_ATH9K is not set -# CONFIG_AR9170_USB is not set +# CONFIG_ATH_COMMON is not set # CONFIG_IPW2100 is not set # CONFIG_IPW2200 is not set # CONFIG_IWLWIFI is not set @@ -832,6 +858,8 @@ CONFIG_LIBERTAS_SDIO=y # CONFIG_ZD1211RW is not set # CONFIG_RT2X00 is not set # CONFIG_HERMES is not set +# CONFIG_WL12XX is not set +# CONFIG_IWM is not set # # Enable WiMAX (Networking options) to see the WiMAX drivers @@ -855,6 +883,7 @@ CONFIG_LIBERTAS_SDIO=y # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_ISDN is not set +# CONFIG_PHONE is not set # # Input device support @@ -878,13 +907,19 @@ CONFIG_INPUT_EVDEV=y # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ADP5588 is not set CONFIG_KEYBOARD_ATKBD=y -# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_QT2160 is not set # CONFIG_KEYBOARD_LKKBD is not set -# CONFIG_KEYBOARD_XTKBD is not set +CONFIG_KEYBOARD_GPIO=y +# CONFIG_KEYBOARD_MATRIX is not set +# CONFIG_KEYBOARD_LM8323 is not set +# CONFIG_KEYBOARD_MAX7359 is not set # CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_OPENCORES is not set # CONFIG_KEYBOARD_STOWAWAY is not set -CONFIG_KEYBOARD_GPIO=y +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set @@ -943,6 +978,7 @@ CONFIG_LEGACY_PTY_COUNT=16 CONFIG_DEVPORT=y CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_COMPAT is not set CONFIG_I2C_CHARDEV=y CONFIG_I2C_HELPER_AUTO=y @@ -998,10 +1034,6 @@ CONFIG_I2C_MV64XXX=y # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_PCF8575 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set @@ -1023,11 +1055,47 @@ CONFIG_SPI_ORION=y # # CONFIG_SPI_SPIDEV is not set # CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set + +# +# PCI GPIO expanders: +# +# CONFIG_GPIO_BT8XX is not set +# CONFIG_GPIO_LANGWELL is not set + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_GPIO_MC33880 is not set + +# +# AC97 GPIO expanders: +# # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set -# CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set CONFIG_SSB_POSSIBLE=y @@ -1041,33 +1109,28 @@ CONFIG_SSB_POSSIBLE=y # # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set # CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set +# CONFIG_MFD_TC6393XB is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM831X is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_MFD_MC13783 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +# CONFIG_REGULATOR is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support # +CONFIG_VGA_ARB=y # CONFIG_DRM is not set # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set @@ -1087,7 +1150,6 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_SOUND is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y -# CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set # @@ -1106,10 +1168,12 @@ CONFIG_HID_BELKIN=y CONFIG_HID_CHERRY=y CONFIG_HID_CHICONY=y CONFIG_HID_CYPRESS=y +CONFIG_HID_DRAGONRISE=y # CONFIG_DRAGONRISE_FF is not set CONFIG_HID_EZKEY=y CONFIG_HID_KYE=y CONFIG_HID_GYRATION=y +CONFIG_HID_TWINHAN=y CONFIG_HID_KENSINGTON=y CONFIG_HID_LOGITECH=y # CONFIG_LOGITECH_FF is not set @@ -1123,9 +1187,14 @@ CONFIG_HID_PETALYNX=y CONFIG_HID_SAMSUNG=y CONFIG_HID_SONY=y CONFIG_HID_SUNPLUS=y +CONFIG_HID_GREENASIA=y # CONFIG_GREENASIA_FF is not set +CONFIG_HID_SMARTJOYPLUS=y +# CONFIG_SMARTJOYPLUS_FF is not set CONFIG_HID_TOPSEED=y +CONFIG_HID_THRUSTMASTER=y # CONFIG_THRUSTMASTER_FF is not set +CONFIG_HID_ZEROPLUS=y # CONFIG_ZEROPLUS_FF is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y @@ -1150,18 +1219,21 @@ CONFIG_USB_DEVICE_CLASS=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_EHCI_TT_NEWSCHED=y # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_ISP1362_HCD is not set # CONFIG_USB_OHCI_HCD is not set # CONFIG_USB_UHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set # CONFIG_USB_WHCI_HCD is not set # CONFIG_USB_HWA_HCD is not set +# CONFIG_USB_MUSB_HDRC is not set # # USB Device Class drivers @@ -1252,11 +1324,14 @@ CONFIG_SDIO_UART=y # MMC/SD/SDIO Host Controller Drivers # # CONFIG_MMC_SDHCI is not set +# CONFIG_MMC_AT91 is not set +# CONFIG_MMC_ATMELMCI is not set # CONFIG_MMC_TIFM_SD is not set CONFIG_MMC_MVSDIO=y # CONFIG_MMC_SPI is not set +# CONFIG_MMC_CB710 is not set +# CONFIG_MMC_VIA_SDMMC is not set # CONFIG_MEMSTICK is not set -# CONFIG_ACCESSIBILITY is not set CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y @@ -1266,7 +1341,7 @@ CONFIG_LEDS_CLASS=y # CONFIG_LEDS_PCA9532 is not set CONFIG_LEDS_GPIO=y CONFIG_LEDS_GPIO_PLATFORM=y -# CONFIG_LEDS_LP5521 is not set +# CONFIG_LEDS_LP3944 is not set # CONFIG_LEDS_PCA955X is not set # CONFIG_LEDS_DAC124S085 is not set # CONFIG_LEDS_BD2802 is not set @@ -1278,11 +1353,14 @@ CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y # CONFIG_LEDS_TRIGGER_BACKLIGHT is not set +# CONFIG_LEDS_TRIGGER_GPIO is not set CONFIG_LEDS_TRIGGER_DEFAULT_ON=y # # iptables trigger is under Netfilter config (LED target) # +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1314,6 +1392,7 @@ CONFIG_RTC_INTF_DEV=y CONFIG_RTC_DRV_S35390A=y # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1325,6 +1404,7 @@ CONFIG_RTC_DRV_S35390A=y # CONFIG_RTC_DRV_R9701 is not set # CONFIG_RTC_DRV_RS5C348 is not set # CONFIG_RTC_DRV_DS3234 is not set +# CONFIG_RTC_DRV_PCF2123 is not set # # Platform RTC drivers @@ -1360,8 +1440,11 @@ CONFIG_DMA_ENGINE=y # CONFIG_ASYNC_TX_DMA is not set # CONFIG_DMATEST is not set # CONFIG_AUXDISPLAY is not set -# CONFIG_REGULATOR is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1379,10 +1462,13 @@ CONFIG_JBD=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1455,7 +1541,6 @@ CONFIG_CRAMFS=y # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set -# CONFIG_NILFS2_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y @@ -1530,6 +1615,7 @@ CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 CONFIG_MAGIC_SYSRQ=y +# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_UNUSED_SYMBOLS is not set CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set @@ -1547,6 +1633,7 @@ CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 # CONFIG_DEBUG_OBJECTS is not set # CONFIG_SLUB_DEBUG_ON is not set # CONFIG_SLUB_STATS is not set +# CONFIG_DEBUG_KMEMLEAK is not set # CONFIG_DEBUG_PREEMPT is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set @@ -1567,12 +1654,14 @@ CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_DEBUG_CREDENTIALS is not set # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_KPROBES_SANITY_TEST is not set # CONFIG_BACKTRACE_SELF_TEST is not set # CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set @@ -1581,25 +1670,12 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_NOP_TRACER=y CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_RING_BUFFER=y +CONFIG_EVENT_TRACING=y +CONFIG_CONTEXT_SWITCH_TRACER=y +CONFIG_RING_BUFFER_ALLOW_SWAP=y CONFIG_TRACING=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_IRQSOFF_TRACER is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_FTRACE_STARTUP_TEST is not set +# CONFIG_FTRACE is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y @@ -1623,7 +1699,6 @@ CONFIG_CRYPTO=y # # Crypto core or helper # -# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD2=y @@ -1665,11 +1740,13 @@ CONFIG_CRYPTO_PCBC=m # # CONFIG_CRYPTO_HMAC is not set # CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_VMAC is not set # # Digest # CONFIG_CRYPTO_CRC32C=y +# CONFIG_CRYPTO_GHASH is not set # CONFIG_CRYPTO_MD4 is not set # CONFIG_CRYPTO_MD5 is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set @@ -1714,6 +1791,7 @@ CONFIG_CRYPTO_ARC4=y # # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y +CONFIG_CRYPTO_DEV_MV_CESA=y # CONFIG_CRYPTO_DEV_HIFN_795X is not set CONFIG_BINARY_PRINTF=y -- cgit v1.2.3 From 3293576c6b7104cdac9c2d10d35abd86b02d7264 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Sat, 7 Nov 2009 20:59:20 -0500 Subject: [ARM] orion5x: update defconfig Signed-off-by: Nicolas Pitre --- arch/arm/configs/orion5x_defconfig | 278 +++++++++++++++++++++++-------------- 1 file changed, 176 insertions(+), 102 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/orion5x_defconfig b/arch/arm/configs/orion5x_defconfig index 9e2385293ecb..5383cd0dff54 100644 --- a/arch/arm/configs/orion5x_defconfig +++ b/arch/arm/configs/orion5x_defconfig @@ -1,15 +1,13 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.30-rc4 -# Mon May 4 14:07:25 2009 +# Linux kernel version: 2.6.32-rc6 +# Sat Nov 7 20:52:21 2009 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_MMU=y -# CONFIG_NO_IOPORT is not set CONFIG_GENERIC_HARDIRQS=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y @@ -18,13 +16,12 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_RWSEM_GENERIC_SPINLOCK=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_VECTORS_BASE=0xffff0000 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y # # General setup @@ -46,11 +43,12 @@ CONFIG_SYSVIPC_SYSCTL=y # # RCU Subsystem # -CONFIG_CLASSIC_RCU=y -# CONFIG_TREE_RCU is not set -# CONFIG_PREEMPT_RCU is not set +CONFIG_TREE_RCU=y +# CONFIG_TREE_PREEMPT_RCU is not set +# CONFIG_RCU_TRACE is not set +CONFIG_RCU_FANOUT=32 +# CONFIG_RCU_FANOUT_EXACT is not set # CONFIG_TREE_RCU_TRACE is not set -# CONFIG_PREEMPT_RCU_TRACE is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 # CONFIG_GROUP_SCHED is not set @@ -69,7 +67,6 @@ CONFIG_SYSCTL_SYSCALL=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_STRIP_ASM_SYMS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y @@ -82,6 +79,10 @@ CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_AIO=y + +# +# Kernel Performance Events And Counters +# CONFIG_VM_EVENT_COUNTERS=y CONFIG_PCI_QUIRKS=y # CONFIG_SLUB_DEBUG is not set @@ -91,13 +92,17 @@ CONFIG_SLUB=y # CONFIG_SLOB is not set CONFIG_PROFILING=y CONFIG_TRACEPOINTS=y -# CONFIG_MARKERS is not set CONFIG_OPROFILE=y CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y CONFIG_KRETPROBES=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y + +# +# GCOV-based kernel profiling +# +# CONFIG_GCOV_KERNEL is not set # CONFIG_SLOW_WORK is not set CONFIG_HAVE_GENERIC_DMA_COHERENT=y CONFIG_RT_MUTEXES=y @@ -109,7 +114,7 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_BLOCK=y -# CONFIG_LBD is not set +CONFIG_LBDAF=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_BLK_DEV_INTEGRITY is not set @@ -130,19 +135,22 @@ CONFIG_DEFAULT_IOSCHED="cfq" # # System Type # +CONFIG_MMU=y # CONFIG_ARCH_AAEC2000 is not set # CONFIG_ARCH_INTEGRATOR is not set # CONFIG_ARCH_REALVIEW is not set # CONFIG_ARCH_VERSATILE is not set # CONFIG_ARCH_AT91 is not set # CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_EBSA110 is not set # CONFIG_ARCH_EP93XX is not set -# CONFIG_ARCH_GEMINI is not set # CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set # CONFIG_ARCH_NETX is not set # CONFIG_ARCH_H720X is not set -# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_NOMADIK is not set # CONFIG_ARCH_IOP13XX is not set # CONFIG_ARCH_IOP32X is not set # CONFIG_ARCH_IOP33X is not set @@ -151,25 +159,27 @@ CONFIG_DEFAULT_IOSCHED="cfq" # CONFIG_ARCH_IXP4XX is not set # CONFIG_ARCH_L7200 is not set # CONFIG_ARCH_KIRKWOOD is not set -# CONFIG_ARCH_KS8695 is not set -# CONFIG_ARCH_NS9XXX is not set # CONFIG_ARCH_LOKI is not set # CONFIG_ARCH_MV78XX0 is not set -# CONFIG_ARCH_MXC is not set CONFIG_ARCH_ORION5X=y +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set # CONFIG_ARCH_PNX4008 is not set # CONFIG_ARCH_PXA is not set -# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_MSM is not set # CONFIG_ARCH_RPC is not set # CONFIG_ARCH_SA1100 is not set # CONFIG_ARCH_S3C2410 is not set # CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5PC1XX is not set # CONFIG_ARCH_SHARK is not set # CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set # CONFIG_ARCH_DAVINCI is not set # CONFIG_ARCH_OMAP is not set -# CONFIG_ARCH_MSM is not set -# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_BCMRING is not set # # Orion Implementations @@ -187,6 +197,9 @@ CONFIG_MACH_WRT350N_V2=y CONFIG_MACH_TS78XX=y CONFIG_MACH_MV2120=y CONFIG_MACH_EDMINI_V2=y +CONFIG_MACH_D2NET=y +CONFIG_MACH_BIGDISK=y +CONFIG_MACH_NET2BIG=y CONFIG_MACH_MSS2=y CONFIG_MACH_WNR854T=y CONFIG_MACH_RD88F5181L_GE=y @@ -202,7 +215,7 @@ CONFIG_CPU_FEROCEON=y CONFIG_CPU_FEROCEON_OLD_ID=y CONFIG_CPU_32v5=y CONFIG_CPU_ABRT_EV5T=y -CONFIG_CPU_PABRT_NOIFAR=y +CONFIG_CPU_PABRT_LEGACY=y CONFIG_CPU_CACHE_VIVT=y CONFIG_CPU_COPY_FEROCEON=y CONFIG_CPU_TLB_FEROCEON=y @@ -215,7 +228,7 @@ CONFIG_CPU_CP15_MMU=y CONFIG_ARM_THUMB=y # CONFIG_CPU_ICACHE_DISABLE is not set # CONFIG_CPU_DCACHE_DISABLE is not set -# CONFIG_OUTER_CACHE is not set +CONFIG_ARM_L1_CACHE_SHIFT=5 # # Bus support @@ -240,11 +253,12 @@ CONFIG_VMSPLIT_3G=y # CONFIG_VMSPLIT_2G is not set # CONFIG_VMSPLIT_1G is not set CONFIG_PAGE_OFFSET=0xC0000000 +# CONFIG_PREEMPT_NONE is not set +# CONFIG_PREEMPT_VOLUNTARY is not set CONFIG_PREEMPT=y CONFIG_HZ=100 CONFIG_AEABI=y CONFIG_OABI_COMPAT=y -CONFIG_ARCH_FLATMEM_HAS_HOLES=y # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set # CONFIG_HIGHMEM is not set @@ -259,12 +273,14 @@ CONFIG_SPLIT_PTLOCK_CPUS=4096 # CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y -CONFIG_UNEVICTABLE_LRU=y CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 CONFIG_LEDS=y CONFIG_LEDS_CPU=y CONFIG_ALIGNMENT_TRAP=y +CONFIG_UACCESS_WITH_MEMCPY=y # # Boot options @@ -308,6 +324,7 @@ CONFIG_PM=y # CONFIG_PM_DEBUG is not set # CONFIG_SUSPEND is not set # CONFIG_APM_EMULATION is not set +# CONFIG_PM_RUNTIME is not set CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_NET=y @@ -356,6 +373,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set # CONFIG_IP_SCTP is not set +# CONFIG_RDS is not set # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set @@ -378,6 +396,7 @@ CONFIG_NET_DSA_MV88E6123_61_65=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set # CONFIG_NET_SCHED is not set # CONFIG_DCB is not set @@ -394,11 +413,15 @@ CONFIG_NET_PKTGEN=m # CONFIG_AF_RXRPC is not set CONFIG_WIRELESS=y # CONFIG_CFG80211 is not set +CONFIG_CFG80211_DEFAULT_PS_VALUE=0 # CONFIG_WIRELESS_OLD_REGULATORY is not set CONFIG_WIRELESS_EXT=y CONFIG_WIRELESS_EXT_SYSFS=y # CONFIG_LIB80211 is not set -# CONFIG_MAC80211 is not set + +# +# CFG80211 needs to be enabled for MAC80211 +# # CONFIG_WIMAX is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -411,6 +434,7 @@ CONFIG_WIRELESS_EXT_SYSFS=y # Generic Driver Options # CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -422,9 +446,9 @@ CONFIG_EXTRA_FIRMWARE="" # CONFIG_CONNECTOR is not set CONFIG_MTD=y # CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_TESTS is not set # CONFIG_MTD_CONCAT is not set CONFIG_MTD_PARTITIONS=y -# CONFIG_MTD_TESTS is not set # CONFIG_MTD_REDBOOT_PARTS is not set CONFIG_MTD_CMDLINE_PARTS=y # CONFIG_MTD_AFS_PARTS is not set @@ -537,6 +561,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_RAM is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_MG_DISK is not set CONFIG_MISC_DEVICES=y # CONFIG_PHANTOM is not set # CONFIG_SGI_IOC4 is not set @@ -552,7 +577,9 @@ CONFIG_MISC_DEVICES=y # # CONFIG_EEPROM_AT24 is not set # CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set # CONFIG_EEPROM_93CX6 is not set +# CONFIG_CB710_CORE is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -576,10 +603,6 @@ CONFIG_BLK_DEV_SR=m # CONFIG_BLK_DEV_SR_VENDOR is not set CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set - -# -# Some SCSI devices (e.g. CD jukebox) support multiple LUNs -# # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set @@ -596,6 +619,8 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_BNX2_ISCSI is not set +# CONFIG_BE2ISCSI is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set @@ -604,6 +629,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set @@ -620,7 +646,6 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -632,11 +657,14 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_PMCRAID is not set # CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_BFA_FC is not set # CONFIG_SCSI_DH is not set # CONFIG_SCSI_OSD_INITIATOR is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set +CONFIG_ATA_VERBOSE_ERROR=y CONFIG_SATA_PMP=y # CONFIG_SATA_AHCI is not set # CONFIG_SATA_SIL24 is not set @@ -658,6 +686,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_ALI is not set # CONFIG_PATA_AMD is not set # CONFIG_PATA_ARTOP is not set +# CONFIG_PATA_ATP867X is not set # CONFIG_PATA_ATIIXP is not set # CONFIG_PATA_CMD640_PCI is not set # CONFIG_PATA_CMD64X is not set @@ -685,6 +714,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set # CONFIG_PATA_RADISYS is not set +# CONFIG_PATA_RDC is not set # CONFIG_PATA_RZ1000 is not set # CONFIG_PATA_SC1200 is not set # CONFIG_PATA_SERVERWORKS is not set @@ -703,13 +733,16 @@ CONFIG_SATA_MV=y # # -# Enable only one of the two stacks, unless you know what you are doing +# You can enable one or both FireWire driver stacks. +# + +# +# See the help texts for more information. # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set CONFIG_NETDEVICES=y -CONFIG_COMPAT_NET_DEV_OPS=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -777,6 +810,8 @@ CONFIG_NET_PCI=y # CONFIG_SMSC9420 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851_MLL is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set # CONFIG_ATL2 is not set @@ -798,6 +833,7 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_CNIC is not set CONFIG_MV643XX_ETH=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set @@ -806,10 +842,7 @@ CONFIG_MV643XX_ETH=y # CONFIG_JME is not set # CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set - -# -# Wireless LAN -# +CONFIG_WLAN=y # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set @@ -835,6 +868,7 @@ CONFIG_MV643XX_ETH=y # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # CONFIG_ISDN is not set +# CONFIG_PHONE is not set # # Input device support @@ -855,13 +889,19 @@ CONFIG_INPUT_EVDEV=y # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y +# CONFIG_KEYBOARD_ADP5588 is not set # CONFIG_KEYBOARD_ATKBD is not set -# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_QT2160 is not set # CONFIG_KEYBOARD_LKKBD is not set -# CONFIG_KEYBOARD_XTKBD is not set +CONFIG_KEYBOARD_GPIO=y +# CONFIG_KEYBOARD_MATRIX is not set +# CONFIG_KEYBOARD_LM8323 is not set +# CONFIG_KEYBOARD_MAX7359 is not set # CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_OPENCORES is not set # CONFIG_KEYBOARD_STOWAWAY is not set -CONFIG_KEYBOARD_GPIO=y +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set @@ -912,6 +952,7 @@ CONFIG_HW_RANDOM_TIMERIOMEM=m CONFIG_DEVPORT=y CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_COMPAT is not set CONFIG_I2C_CHARDEV=y CONFIG_I2C_HELPER_AUTO=y @@ -967,20 +1008,55 @@ CONFIG_I2C_MV64XXX=y # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_PCF8575 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set + +# +# PPS support +# +# CONFIG_PPS is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set + +# +# PCI GPIO expanders: +# +# CONFIG_GPIO_BT8XX is not set +# CONFIG_GPIO_LANGWELL is not set + +# +# SPI GPIO expanders: +# + +# +# AC97 GPIO expanders: +# # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Native drivers +# # CONFIG_SENSORS_AD7414 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set @@ -1030,6 +1106,8 @@ CONFIG_SENSORS_LM75=y # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set +# CONFIG_SENSORS_TMP421 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set # CONFIG_SENSORS_VT8231 is not set @@ -1041,9 +1119,7 @@ CONFIG_SENSORS_LM75=y # CONFIG_SENSORS_W83L786NG is not set # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set -# CONFIG_HWMON_DEBUG_CHIP is not set # CONFIG_THERMAL is not set -# CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set CONFIG_SSB_POSSIBLE=y @@ -1057,33 +1133,26 @@ CONFIG_SSB_POSSIBLE=y # # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_TPS65010 is not set # CONFIG_TWL4030_CORE is not set # CONFIG_MFD_TMIO is not set +# CONFIG_MFD_TC6393XB is not set # CONFIG_PMIC_DA903X is not set # CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM831X is not set # CONFIG_MFD_WM8350_I2C is not set # CONFIG_MFD_PCF50633 is not set - -# -# Multimedia devices -# - -# -# Multimedia core support -# -# CONFIG_VIDEO_DEV is not set -# CONFIG_DVB_CORE is not set -# CONFIG_VIDEO_MEDIA is not set - -# -# Multimedia drivers -# -# CONFIG_DAB is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_REGULATOR is not set +# CONFIG_MEDIA_SUPPORT is not set # # Graphics support # +# CONFIG_VGA_ARB is not set # CONFIG_DRM is not set # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set @@ -1097,7 +1166,6 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_SOUND is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y -# CONFIG_HID_DEBUG is not set # CONFIG_HIDRAW is not set # @@ -1116,10 +1184,11 @@ CONFIG_USB_HID=y # CONFIG_HID_CHERRY is not set # CONFIG_HID_CHICONY is not set # CONFIG_HID_CYPRESS is not set -# CONFIG_DRAGONRISE_FF is not set +# CONFIG_HID_DRAGONRISE is not set # CONFIG_HID_EZKEY is not set # CONFIG_HID_KYE is not set # CONFIG_HID_GYRATION is not set +# CONFIG_HID_TWINHAN is not set # CONFIG_HID_KENSINGTON is not set # CONFIG_HID_LOGITECH is not set # CONFIG_HID_MICROSOFT is not set @@ -1130,10 +1199,11 @@ CONFIG_USB_HID=y # CONFIG_HID_SAMSUNG is not set # CONFIG_HID_SONY is not set # CONFIG_HID_SUNPLUS is not set -# CONFIG_GREENASIA_FF is not set +# CONFIG_HID_GREENASIA is not set +# CONFIG_HID_SMARTJOYPLUS is not set # CONFIG_HID_TOPSEED is not set -# CONFIG_THRUSTMASTER_FF is not set -# CONFIG_ZEROPLUS_FF is not set +# CONFIG_HID_THRUSTMASTER is not set +# CONFIG_HID_ZEROPLUS is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1160,18 +1230,21 @@ CONFIG_USB_DEVICE_CLASS=y # USB Host Controller Drivers # # CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_XHCI_HCD is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_EHCI_TT_NEWSCHED=y # CONFIG_USB_OXU210HP_HCD is not set # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_ISP1362_HCD is not set # CONFIG_USB_OHCI_HCD is not set # CONFIG_USB_UHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set # CONFIG_USB_WHCI_HCD is not set # CONFIG_USB_HWA_HCD is not set +# CONFIG_USB_MUSB_HDRC is not set # # USB Device Class drivers @@ -1248,7 +1321,6 @@ CONFIG_USB_STORAGE_JUMPSHOT=y # CONFIG_UWB is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set -# CONFIG_ACCESSIBILITY is not set CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y @@ -1258,7 +1330,7 @@ CONFIG_LEDS_CLASS=y # CONFIG_LEDS_PCA9532 is not set CONFIG_LEDS_GPIO=y CONFIG_LEDS_GPIO_PLATFORM=y -# CONFIG_LEDS_LP5521 is not set +# CONFIG_LEDS_LP3944 is not set # CONFIG_LEDS_PCA955X is not set # CONFIG_LEDS_BD2802 is not set @@ -1269,11 +1341,14 @@ CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y # CONFIG_LEDS_TRIGGER_BACKLIGHT is not set +# CONFIG_LEDS_TRIGGER_GPIO is not set CONFIG_LEDS_TRIGGER_DEFAULT_ON=y # # iptables trigger is under Netfilter config (LED target) # +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1306,6 +1381,7 @@ CONFIG_RTC_DRV_M41T80=y CONFIG_RTC_DRV_S35390A=y # CONFIG_RTC_DRV_FM3130 is not set # CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set # # SPI RTC drivers @@ -1344,8 +1420,11 @@ CONFIG_DMA_ENGINE=y # CONFIG_ASYNC_TX_DMA is not set # CONFIG_DMATEST is not set # CONFIG_AUXDISPLAY is not set -# CONFIG_REGULATOR is not set # CONFIG_UIO is not set + +# +# TI VLYNQ +# # CONFIG_STAGING is not set # @@ -1358,10 +1437,10 @@ CONFIG_EXT3_FS=y # CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set # CONFIG_EXT3_FS_XATTR is not set CONFIG_EXT4_FS=m -# CONFIG_EXT4DEV_COMPAT is not set CONFIG_EXT4_FS_XATTR=y # CONFIG_EXT4_FS_POSIX_ACL is not set # CONFIG_EXT4_FS_SECURITY is not set +# CONFIG_EXT4_DEBUG is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_JBD2=m @@ -1370,10 +1449,13 @@ CONFIG_FS_MBCACHE=m # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set -CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1446,7 +1528,6 @@ CONFIG_CRAMFS=y # CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set -# CONFIG_NILFS2_FS is not set CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y @@ -1537,6 +1618,7 @@ CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 CONFIG_MAGIC_SYSRQ=y +# CONFIG_STRIP_ASM_SYMS is not set # CONFIG_UNUSED_SYMBOLS is not set CONFIG_DEBUG_FS=y # CONFIG_HEADERS_CHECK is not set @@ -1552,6 +1634,7 @@ CONFIG_SCHED_DEBUG=y CONFIG_SCHEDSTATS=y # CONFIG_TIMER_STATS is not set # CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_KMEMLEAK is not set CONFIG_DEBUG_PREEMPT=y # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set @@ -1572,6 +1655,7 @@ CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_DEBUG_CREDENTIALS is not set CONFIG_FRAME_POINTER=y # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set @@ -1579,6 +1663,7 @@ CONFIG_FRAME_POINTER=y # CONFIG_KPROBES_SANITY_TEST is not set # CONFIG_BACKTRACE_SELF_TEST is not set # CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set CONFIG_LATENCYTOP=y @@ -1587,25 +1672,12 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_NOP_TRACER=y CONFIG_HAVE_FUNCTION_TRACER=y CONFIG_RING_BUFFER=y +CONFIG_EVENT_TRACING=y +CONFIG_CONTEXT_SWITCH_TRACER=y +CONFIG_RING_BUFFER_ALLOW_SWAP=y CONFIG_TRACING=y CONFIG_TRACING_SUPPORT=y - -# -# Tracers -# -# CONFIG_FUNCTION_TRACER is not set -# CONFIG_IRQSOFF_TRACER is not set -# CONFIG_PREEMPT_TRACER is not set -# CONFIG_SCHED_TRACER is not set -# CONFIG_CONTEXT_SWITCH_TRACER is not set -# CONFIG_EVENT_TRACER is not set -# CONFIG_BOOT_TRACER is not set -# CONFIG_TRACE_BRANCH_PROFILING is not set -# CONFIG_STACK_TRACER is not set -# CONFIG_KMEMTRACE is not set -# CONFIG_WORKQUEUE_TRACER is not set -# CONFIG_BLK_DEV_IO_TRACE is not set -# CONFIG_FTRACE_STARTUP_TEST is not set +# CONFIG_FTRACE is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y @@ -1629,20 +1701,19 @@ CONFIG_CRYPTO=y # # Crypto core or helper # -# CONFIG_CRYPTO_FIPS is not set -CONFIG_CRYPTO_ALGAPI=m -CONFIG_CRYPTO_ALGAPI2=m -CONFIG_CRYPTO_AEAD2=m +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y +CONFIG_CRYPTO_AEAD2=y CONFIG_CRYPTO_BLKCIPHER=m -CONFIG_CRYPTO_BLKCIPHER2=m -CONFIG_CRYPTO_HASH2=m -CONFIG_CRYPTO_RNG2=m -CONFIG_CRYPTO_PCOMP=m +CONFIG_CRYPTO_BLKCIPHER2=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_PCOMP=y CONFIG_CRYPTO_MANAGER=m -CONFIG_CRYPTO_MANAGER2=m +CONFIG_CRYPTO_MANAGER2=y # CONFIG_CRYPTO_GF128MUL is not set # CONFIG_CRYPTO_NULL is not set -CONFIG_CRYPTO_WORKQUEUE=m +CONFIG_CRYPTO_WORKQUEUE=y # CONFIG_CRYPTO_CRYPTD is not set # CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_TEST is not set @@ -1670,11 +1741,13 @@ CONFIG_CRYPTO_PCBC=m # # CONFIG_CRYPTO_HMAC is not set # CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_VMAC is not set # # Digest # # CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_GHASH is not set # CONFIG_CRYPTO_MD4 is not set # CONFIG_CRYPTO_MD5 is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set @@ -1691,7 +1764,7 @@ CONFIG_CRYPTO_PCBC=m # # Ciphers # -# CONFIG_CRYPTO_AES is not set +CONFIG_CRYPTO_AES=y # CONFIG_CRYPTO_ANUBIS is not set # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_BLOWFISH is not set @@ -1719,6 +1792,7 @@ CONFIG_CRYPTO_PCBC=m # # CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y +CONFIG_CRYPTO_DEV_MV_CESA=y # CONFIG_CRYPTO_DEV_HIFN_795X is not set CONFIG_BINARY_PRINTF=y -- cgit v1.2.3 From 158bc5af3d49be49c33dc06ff90c4f754c7d4f1b Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Sat, 7 Nov 2009 07:35:06 +0100 Subject: ARM: 5784/1: fix early boot machine ID mismatch error display That code was refactored a long time ago, but one particular label didn't get adjusted properly which broke the listing of supported machines. Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/kernel/head-common.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/kernel/head-common.S b/arch/arm/kernel/head-common.S index 885a7214418d..b9505aa267c0 100644 --- a/arch/arm/kernel/head-common.S +++ b/arch/arm/kernel/head-common.S @@ -97,7 +97,7 @@ __error_a: bl printhex8 adr r0, str_a2 bl printascii - adr r3, 3f + adr r3, 4f ldmia r3, {r4, r5, r6} @ get machine desc list sub r4, r3, r4 @ get offset between virt&phys add r5, r5, r4 @ convert virt addresses to -- cgit v1.2.3 From bfd2e29f04e5f048ea62677811d1244badd6661e Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 8 Nov 2009 20:05:28 +0000 Subject: [ARM] Fix test for unimplemented ARM syscalls The existing test always failed since 'no' was always greater than 0x7ff. Signed-off-by: Russell King --- arch/arm/kernel/traps.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 95718a6b50a6..1bbda04a5380 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -573,7 +573,7 @@ asmlinkage int arm_syscall(int no, struct pt_regs *regs) if not implemented, rather than raising SIGILL. This way the calling program can gracefully determine whether a feature is supported. */ - if (no <= 0x7ff) + if ((no & 0xffff) <= 0x7ff) return -ENOSYS; break; } -- cgit v1.2.3 From a3323b72b964471650a6128de4e10f8e88d47ae1 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Tue, 3 Nov 2009 14:42:04 +0000 Subject: ARM: SMDK6410: Configure GPIO pull up for WM835x IRQ line When used with the WM1190-EV1 board we can use the internal pull up resistor of the CPU to provide the required pull for the IRQ line. Without this interrupts from the WM835x don't work in the default WM1190-EV1 hardwaer configuration. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/mach-s3c6410/mach-smdk6410.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-s3c6410/mach-smdk6410.c b/arch/arm/mach-s3c6410/mach-smdk6410.c index ea51dbe76e3e..9f1a21462620 100644 --- a/arch/arm/mach-s3c6410/mach-smdk6410.c +++ b/arch/arm/mach-s3c6410/mach-smdk6410.c @@ -320,6 +320,9 @@ static int __init smdk6410_wm8350_init(struct wm8350 *wm8350) { int i; + /* Configure the IRQ line */ + s3c_gpio_setpull(S3C64XX_GPN(12), S3C_GPIO_PULL_UP); + /* Instantiate the regulators */ for (i = 0; i < ARRAY_SIZE(wm1190_regulators); i++) wm8350_register_regulator(wm8350, -- cgit v1.2.3 From c7a19787195fcc90aabc3a71f29647ba9a443efe Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Tue, 3 Nov 2009 14:42:10 +0000 Subject: ARM: SMDK6410: Allocate more GPIO space for WM1190-EV1 The WM835x has some GPIOs on it, allocate some space so we can use them with gpiolib. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/mach-s3c6410/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-s3c6410/Kconfig b/arch/arm/mach-s3c6410/Kconfig index 53fc3ff657f7..72d4b11b2077 100644 --- a/arch/arm/mach-s3c6410/Kconfig +++ b/arch/arm/mach-s3c6410/Kconfig @@ -77,6 +77,7 @@ config SMDK6410_WM1190_EV1 depends on MACH_SMDK6410 select REGULATOR select REGULATOR_WM8350 + select S3C24XX_GPIO_EXTRA64 select MFD_WM8350_I2C select MFD_WM8350_CONFIG_MODE_0 select MFD_WM8350_CONFIG_MODE_3 -- cgit v1.2.3 From 54489cd46a3a268ed981c681726c6d690883f076 Mon Sep 17 00:00:00 2001 From: Maurus Cuelenaere Date: Wed, 4 Nov 2009 13:13:29 +0100 Subject: ARM: S3C64XX: Remove duplicate s3c_dma_has_circular() definition for S3C64xx. This patch removes the duplicated s3c_dma_has_circular() definition and so fixes compilation for S3C64xx. Signed-off-by: Maurus Cuelenaere Signed-off-by: Ben Dooks --- arch/arm/mach-s3c6400/include/mach/dma.h | 5 ----- 1 file changed, 5 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-s3c6400/include/mach/dma.h b/arch/arm/mach-s3c6400/include/mach/dma.h index 004edab23954..1067619f0ba0 100644 --- a/arch/arm/mach-s3c6400/include/mach/dma.h +++ b/arch/arm/mach-s3c6400/include/mach/dma.h @@ -68,11 +68,6 @@ static __inline__ int s3c_dma_has_circular(void) #define S3C2410_DMAF_CIRCULAR (1 << 0) -static inline bool s3c_dma_has_circular(void) -{ - return false; -} - #include #endif /* __ASM_ARCH_IRQ_H */ -- cgit v1.2.3 From b3c5496fbfc2e5f64bb85b142615717850fee980 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 9 Nov 2009 23:45:47 +0000 Subject: ARM: S3C64XX: Tidy definition and comments in s3c_dma_has_circular() The recent changes to arch/arm/mach-s3c6400/include/mach/dma.h have left an out of date comment in there as well as accidentally changing the type of the function. Fix the commit 54489cd46a3a268ed981c681726c6d690883f076 Signed-off-by: Ben Dooks --- arch/arm/mach-s3c6400/include/mach/dma.h | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-s3c6400/include/mach/dma.h b/arch/arm/mach-s3c6400/include/mach/dma.h index 1067619f0ba0..6723860748be 100644 --- a/arch/arm/mach-s3c6400/include/mach/dma.h +++ b/arch/arm/mach-s3c6400/include/mach/dma.h @@ -58,12 +58,9 @@ enum dma_ch { DMACH_MAX /* the end */ }; -static __inline__ int s3c_dma_has_circular(void) +static __inline__ bool s3c_dma_has_circular(void) { - /* we will be supporting ciruclar buffers as soon as we have DMA - * engine support. - */ - return 1; + return true; } #define S3C2410_DMAF_CIRCULAR (1 << 0) -- cgit v1.2.3 From 210012a6cd8770a73d1aa74b742667b462d04511 Mon Sep 17 00:00:00 2001 From: Jassi Brar Date: Thu, 5 Nov 2009 13:44:20 +0900 Subject: ARM: S3C64XX: DMA: Protect buffer pointers while manipulation Ensure the DMA buffer points are not updated from another source during the process of enquing a buffer. Signed-off-by: Jassi Brar [ben-linux@fluff.org: Updated patch comment] Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/dma.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c64xx/dma.c b/arch/arm/plat-s3c64xx/dma.c index 266a10745a85..6fa706f0f42a 100644 --- a/arch/arm/plat-s3c64xx/dma.c +++ b/arch/arm/plat-s3c64xx/dma.c @@ -339,6 +339,7 @@ int s3c2410_dma_enqueue(unsigned int channel, void *id, struct s3c64xx_dma_buff *next; struct s3c64xx_dma_buff *buff; struct pl080s_lli *lli; + unsigned long flags; int ret; WARN_ON(!chan); @@ -366,6 +367,8 @@ int s3c2410_dma_enqueue(unsigned int channel, void *id, s3c64xx_dma_fill_lli(chan, lli, data, size); + local_irq_save(flags); + if ((next = chan->next) != NULL) { struct s3c64xx_dma_buff *end = chan->end; struct pl080s_lli *endlli = end->lli; @@ -397,6 +400,8 @@ int s3c2410_dma_enqueue(unsigned int channel, void *id, s3c64xx_lli_to_regs(chan, lli); } + local_irq_restore(flags); + show_lli(lli); dbg_showchan(chan); -- cgit v1.2.3 From 6d0b8627d545aed7d4bcaad2156b6cb95e105715 Mon Sep 17 00:00:00 2001 From: Jassi Brar Date: Thu, 5 Nov 2009 13:44:26 +0900 Subject: ARM: S3C64XX: DMA: Unify callback functions for success/failure Replace s3c64xx_dma_tcirq and s3c64xx_dma_errirq with the common s3c64xx_dma_buffdone. Signed-off-by: Jassi Brar Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/dma.c | 34 +++++++++++++--------------------- 1 file changed, 13 insertions(+), 21 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c64xx/dma.c b/arch/arm/plat-s3c64xx/dma.c index 6fa706f0f42a..5a08a86419dd 100644 --- a/arch/arm/plat-s3c64xx/dma.c +++ b/arch/arm/plat-s3c64xx/dma.c @@ -565,26 +565,11 @@ int s3c2410_dma_free(unsigned int channel, struct s3c2410_dma_client *client) EXPORT_SYMBOL(s3c2410_dma_free); - -static void s3c64xx_dma_tcirq(struct s3c64xx_dmac *dmac, int offs) -{ - struct s3c2410_dma_chan *chan = dmac->channels + offs; - - /* note, we currently do not bother to work out which buffer - * or buffers have been completed since the last tc-irq. */ - - if (chan->callback_fn) - (chan->callback_fn)(chan, chan->curr->pw, 0, S3C2410_RES_OK); -} - -static void s3c64xx_dma_errirq(struct s3c64xx_dmac *dmac, int offs) -{ - printk(KERN_DEBUG "%s: offs %d\n", __func__, offs); -} - static irqreturn_t s3c64xx_dma_irq(int irq, void *pw) { struct s3c64xx_dmac *dmac = pw; + struct s3c2410_dma_chan *chan; + enum s3c2410_dma_buffresult res; u32 tcstat, errstat; u32 bit; int offs; @@ -593,15 +578,22 @@ static irqreturn_t s3c64xx_dma_irq(int irq, void *pw) errstat = readl(dmac->regs + PL080_ERR_STATUS); for (offs = 0, bit = 1; offs < 8; offs++, bit <<= 1) { + + if (!(errstat & bit) && !(tcstat & bit)) + continue; + + chan = dmac->channels + offs; + res = S3C2410_RES_ERR; + if (tcstat & bit) { writel(bit, dmac->regs + PL080_TC_CLEAR); - s3c64xx_dma_tcirq(dmac, offs); + res = S3C2410_RES_OK; } - if (errstat & bit) { - s3c64xx_dma_errirq(dmac, offs); + if (errstat & bit) writel(bit, dmac->regs + PL080_ERR_CLEAR); - } + + s3c64xx_dma_bufffdone(chan, chan->curr, res); } return IRQ_HANDLED; -- cgit v1.2.3 From 7507f39c57d4a285aea11c379fbc65c2b3f375ef Mon Sep 17 00:00:00 2001 From: Jassi Brar Date: Thu, 5 Nov 2009 13:44:45 +0900 Subject: ARM: S3C64XX: DMA: Make src and dst transfer size same Some devices don't seem to work if the source and desitnation transfer widths are not same. For example, SPI dma xfers, with 8bits/word, don't work without this patch. Signed-off-by: Jassi Brar Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/dma.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c64xx/dma.c b/arch/arm/plat-s3c64xx/dma.c index 5a08a86419dd..a94281bb84d6 100644 --- a/arch/arm/plat-s3c64xx/dma.c +++ b/arch/arm/plat-s3c64xx/dma.c @@ -151,8 +151,6 @@ static void s3c64xx_dma_fill_lli(struct s3c2410_dma_chan *chan, src = chan->dev_addr; dst = data; control0 = PL080_CONTROL_SRC_AHB2; - control0 |= (u32)chan->hw_width << PL080_CONTROL_SWIDTH_SHIFT; - control0 |= 2 << PL080_CONTROL_DWIDTH_SHIFT; control0 |= PL080_CONTROL_DST_INCR; break; @@ -160,8 +158,6 @@ static void s3c64xx_dma_fill_lli(struct s3c2410_dma_chan *chan, src = data; dst = chan->dev_addr; control0 = PL080_CONTROL_DST_AHB2; - control0 |= (u32)chan->hw_width << PL080_CONTROL_DWIDTH_SHIFT; - control0 |= 2 << PL080_CONTROL_SWIDTH_SHIFT; control0 |= PL080_CONTROL_SRC_INCR; break; default: @@ -173,6 +169,8 @@ static void s3c64xx_dma_fill_lli(struct s3c2410_dma_chan *chan, control1 = size >> chan->hw_width; /* size in no of xfers */ control0 |= PL080_CONTROL_PROT_SYS; /* always in priv. mode */ control0 |= PL080_CONTROL_TC_IRQ_EN; /* always fire IRQ */ + control0 |= (u32)chan->hw_width << PL080_CONTROL_DWIDTH_SHIFT; + control0 |= (u32)chan->hw_width << PL080_CONTROL_SWIDTH_SHIFT; lli->src_addr = src; lli->dst_addr = dst; -- cgit v1.2.3 From 9b08284bf22f438baa2d6b68015ff17ddb431a61 Mon Sep 17 00:00:00 2001 From: Jassi Brar Date: Thu, 5 Nov 2009 13:44:33 +0900 Subject: ARM: S3C64XX: DMA: Callback with correct buffer pointer buffdone callback should be called per buffer request with pointer to the latest serviced request. 'next' should point to the one next to currently active. Signed-off-by: Jassi Brar Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/dma.c | 29 ++++++++++++++++++++++++++++- 1 file changed, 28 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c64xx/dma.c b/arch/arm/plat-s3c64xx/dma.c index a94281bb84d6..7d12eb8fa58d 100644 --- a/arch/arm/plat-s3c64xx/dma.c +++ b/arch/arm/plat-s3c64xx/dma.c @@ -576,6 +576,7 @@ static irqreturn_t s3c64xx_dma_irq(int irq, void *pw) errstat = readl(dmac->regs + PL080_ERR_STATUS); for (offs = 0, bit = 1; offs < 8; offs++, bit <<= 1) { + struct s3c64xx_dma_buff *buff; if (!(errstat & bit) && !(tcstat & bit)) continue; @@ -591,7 +592,33 @@ static irqreturn_t s3c64xx_dma_irq(int irq, void *pw) if (errstat & bit) writel(bit, dmac->regs + PL080_ERR_CLEAR); - s3c64xx_dma_bufffdone(chan, chan->curr, res); + /* 'next' points to the buffer that is next to the + * currently active buffer. + * For CIRCULAR queues, 'next' will be same as 'curr' + * when 'end' is the active buffer. + */ + buff = chan->curr; + while (buff && buff != chan->next + && buff->next != chan->next) + buff = buff->next; + + if (!buff) + BUG(); + + if (buff == chan->next) + buff = chan->end; + + s3c64xx_dma_bufffdone(chan, buff, res); + + /* Update 'next' */ + buff = chan->next; + if (chan->next == chan->end) { + chan->next = chan->curr; + if (!(chan->flags & S3C2410_DMAF_CIRCULAR)) + chan->end = NULL; + } else { + chan->next = buff->next; + } } return IRQ_HANDLED; -- cgit v1.2.3 From 336b1a3181d81db85c0af3d0c18fe0a04b4d5126 Mon Sep 17 00:00:00 2001 From: Jassi Brar Date: Thu, 5 Nov 2009 13:44:39 +0900 Subject: ARM: S3C64XX: DMA: Free node for non-circular queues We need to free the buff and lli nodes if the buffer queue is not CIRCULAR. Signed-off-by: Jassi Brar Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/dma.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/plat-s3c64xx/dma.c b/arch/arm/plat-s3c64xx/dma.c index 7d12eb8fa58d..d554b936fcfb 100644 --- a/arch/arm/plat-s3c64xx/dma.c +++ b/arch/arm/plat-s3c64xx/dma.c @@ -610,6 +610,12 @@ static irqreturn_t s3c64xx_dma_irq(int irq, void *pw) s3c64xx_dma_bufffdone(chan, buff, res); + /* Free the node and update curr, if non-circular queue */ + if (!(chan->flags & S3C2410_DMAF_CIRCULAR)) { + chan->curr = buff->next; + s3c64xx_dma_freebuff(buff); + } + /* Update 'next' */ buff = chan->next; if (chan->next == chan->end) { -- cgit v1.2.3 From cc20d42986d5807cbe4f5c7c8e3dab2e59ea0db3 Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 9 Nov 2009 23:53:29 +0000 Subject: ARM: Use a definition for the userspace cmpxchg emulation syscall Use a definition for the cmpxchg SWI instead of hard-coding the number. Signed-off-by: Russell King Acked-by: Nicolas Pitre --- arch/arm/include/asm/unistd.h | 9 +++++++++ arch/arm/kernel/entry-armv.S | 7 ++++--- arch/arm/kernel/traps.c | 2 +- 3 files changed, 14 insertions(+), 4 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h index 7020217fc49f..4e506d09e5f9 100644 --- a/arch/arm/include/asm/unistd.h +++ b/arch/arm/include/asm/unistd.h @@ -402,6 +402,15 @@ #define __ARM_NR_usr32 (__ARM_NR_BASE+4) #define __ARM_NR_set_tls (__ARM_NR_BASE+5) +/* + * *NOTE*: This is a ghost syscall private to the kernel. Only the + * __kuser_cmpxchg code in entry-armv.S should be aware of its + * existence. Don't ever use this from user code. + */ +#ifdef __KERNEL__ +#define __ARM_NR_cmpxchg (__ARM_NR_BASE+0x00fff0) +#endif + /* * The following syscalls are obsolete and no longer available for EABI. */ diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index 0022b4d57f8b..d2903e3bc861 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -21,6 +21,7 @@ #include #include #include +#include #include "entry-header.S" @@ -908,10 +909,10 @@ __kuser_cmpxchg: @ 0xffff0fc0 * A special ghost syscall is used for that (see traps.c). */ stmfd sp!, {r7, lr} - mov r7, #0xff00 @ 0xfff0 into r7 for EABI - orr r7, r7, #0xf0 - swi #0x9ffff0 + ldr r7, =1f @ it's 20 bits + swi __ARM_NR_cmpxchg ldmfd sp!, {r7, pc} +1: .word __ARM_NR_cmpxchg #elif __LINUX_ARM_ARCH__ < 6 diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 1bbda04a5380..3f361a783f43 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -528,7 +528,7 @@ asmlinkage int arm_syscall(int no, struct pt_regs *regs) * __kuser_cmpxchg code in entry-armv.S should be aware of its * existence. Don't ever use this from user code. */ - case 0xfff0: + case NR(cmpxchg): for (;;) { extern void do_DataAbort(unsigned long addr, unsigned int fsr, struct pt_regs *regs); -- cgit v1.2.3 From ee90732456fe8e75406fdd3cd136a4bfb7ce31f5 Mon Sep 17 00:00:00 2001 From: Tao Hu Date: Tue, 10 Nov 2009 18:55:17 -0800 Subject: omap: Fix race condition in omap dma driver The bug could cause irq enable bit of one DMA channel is cleared/set unexpectedly when 2 (or more) drivers are calling omap_request_dma()/omap_free_dma() simultaneously Signed-off-by: Fei Yang Signed-off-by: Tao Hu Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/dma.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index b53125f41293..02ed94526aa3 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -691,13 +691,16 @@ static inline void disable_lnk(int lch) static inline void omap2_enable_irq_lch(int lch) { u32 val; + unsigned long flags; if (!cpu_class_is_omap2()) return; + spin_lock_irqsave(&dma_chan_lock, flags); val = dma_read(IRQENABLE_L0); val |= 1 << lch; dma_write(val, IRQENABLE_L0); + spin_unlock_irqrestore(&dma_chan_lock, flags); } int omap_request_dma(int dev_id, const char *dev_name, @@ -799,10 +802,13 @@ void omap_free_dma(int lch) if (cpu_class_is_omap2()) { u32 val; + + spin_lock_irqsave(&dma_chan_lock, flags); /* Disable interrupts */ val = dma_read(IRQENABLE_L0); val &= ~(1 << lch); dma_write(val, IRQENABLE_L0); + spin_unlock_irqrestore(&dma_chan_lock, flags); /* Clear the CSR register and IRQ status register */ dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(lch)); -- cgit v1.2.3 From 6d1352420901b0a74e6149a891ff4457f7199651 Mon Sep 17 00:00:00 2001 From: Tobias Klauser Date: Tue, 10 Nov 2009 18:55:19 -0800 Subject: omap: Use resource_size Use the resource_size function instead of manually calculating the resource size. This reduces the chance of introducing off-by-one errors and actually fixes one in mailbox.c. Signed-off-by: Tobias Klauser Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/gpmc.c | 2 +- arch/arm/mach-omap2/mailbox.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 15876828db23..f8657568b1ba 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -366,7 +366,7 @@ int gpmc_cs_request(int cs, unsigned long size, unsigned long *base) if (r < 0) goto out; - gpmc_cs_enable_mem(cs, res->start, res->end - res->start + 1); + gpmc_cs_enable_mem(cs, res->start, resource_size(res)); *base = res->start; gpmc_cs_set_reserved(cs, 1); out: diff --git a/arch/arm/mach-omap2/mailbox.c b/arch/arm/mach-omap2/mailbox.c index c035ad3426d0..ef57b38a56a4 100644 --- a/arch/arm/mach-omap2/mailbox.c +++ b/arch/arm/mach-omap2/mailbox.c @@ -300,7 +300,7 @@ static int __devinit omap2_mbox_probe(struct platform_device *pdev) dev_err(&pdev->dev, "invalid mem resource\n"); return -ENODEV; } - mbox_base = ioremap(res->start, res->end - res->start); + mbox_base = ioremap(res->start, resource_size(res)); if (!mbox_base) return -ENOMEM; -- cgit v1.2.3 From 8561a84f85eccddf46212622f1f18317a220891b Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Wed, 11 Nov 2009 11:00:03 -0800 Subject: omap: Fix omapfb/lcdc on OMAP1510 broken when PM set With CONFIG_PM=y, the omapfb/lcdc device on Amstrad Delta, after initially starting correctly, breaks with the following error messages: omapfb omapfb: resetting (status 0xffffff96,reset count 1) ... omapfb omapfb: resetting (status 0xffffff96,reset count 100) omapfb omapfb: too many reset attempts, giving up. Looking closer at this I have found that it had been broken almost 2 years ago with commit 2418996e3b100114edb2ae110d5d4acb928909d2, PM fixes for OMAP1. The definite reason for broken omapfb/lcdc behavoiur in PM mode appeared to be ARM_IDLECT1:IDLIF_ARM (bit 6) put into idle regardless of LCD DMA possibly running. The bit were set based on return value of the omap_dma_running() function that did not check for dedicated LCD DMA channel status. The patch below fixes this. Note that the hardcoded register value will be fixed during the next merge cycle to use OMAP_LCDC_ defines. Currently the OMAP_LCDC_ defines are local to drivers/video/omap/lcdc.c, so let's not start moving those right now. Created against linux-2.6.32-rc6 Tested on Amstrad Delta Signed-off-by: Janusz Krzysztofik Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/dma.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c index 02ed94526aa3..68eaae324b6a 100644 --- a/arch/arm/plat-omap/dma.c +++ b/arch/arm/plat-omap/dma.c @@ -1114,6 +1114,14 @@ int omap_dma_running(void) { int lch; + /* + * On OMAP1510, internal LCD controller will start the transfer + * when it gets enabled, so assume DMA running if LCD enabled. + */ + if (cpu_is_omap1510()) + if (omap_readw(0xfffec000 + 0x00) & (1 << 0)) + return 1; + /* Check if LCD DMA is running */ if (cpu_is_omap16xx()) if (omap_readw(OMAP1610_DMA_LCD_CCR) & OMAP_DMA_CCR_EN) -- cgit v1.2.3 From 01943244552c6c747050e7d9d3a10ce31030b4e6 Mon Sep 17 00:00:00 2001 From: Janusz Krzysztofik Date: Wed, 11 Nov 2009 11:00:34 -0800 Subject: omap1: Amstrad Delta defconfig fixes The patch provides the following fixes: - keep kernel small enough to boot with standard tools, - ensure compatibility with both new and legacy distros, - turn on support for recently added or fixed hardware features. Created and tested against linux-2.6.32-rc5. Signed-off-by: Janusz Krzysztofik Signed-off-by: Tony Lindgren --- arch/arm/configs/ams_delta_defconfig | 24 +++++++++++++++++------- 1 file changed, 17 insertions(+), 7 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/ams_delta_defconfig b/arch/arm/configs/ams_delta_defconfig index 764732529ea3..e8f7380b67d6 100644 --- a/arch/arm/configs/ams_delta_defconfig +++ b/arch/arm/configs/ams_delta_defconfig @@ -55,10 +55,10 @@ CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SYSCTL=y -# CONFIG_EMBEDDED is not set +CONFIG_EMBEDDED=y CONFIG_UID16=y CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS is not set # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y @@ -224,7 +224,7 @@ CONFIG_CPU_CP15_MMU=y # # Processor Features # -# CONFIG_ARM_THUMB is not set +CONFIG_ARM_THUMB=y # CONFIG_CPU_ICACHE_DISABLE is not set # CONFIG_CPU_DCACHE_DISABLE is not set CONFIG_CPU_DCACHE_WRITETHROUGH=y @@ -248,7 +248,7 @@ CONFIG_CPU_DCACHE_WRITETHROUGH=y # CONFIG_HIGH_RES_TIMERS is not set CONFIG_PREEMPT=y CONFIG_HZ=100 -# CONFIG_AEABI is not set +CONFIG_AEABI=y # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -299,7 +299,9 @@ CONFIG_BINFMT_ELF=y # # Power management options # -# CONFIG_PM is not set +CONFIG_PM=y +# CONFIG_SUSPEND is not set +CONFIG_PM_RUNTIME=y # # Networking @@ -670,7 +672,7 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set # CONFIG_INPUT_TSDEV is not set -# CONFIG_INPUT_EVDEV is not set +CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set # @@ -784,6 +786,7 @@ CONFIG_I2C_OMAP=y # # CONFIG_SPI is not set # CONFIG_SPI_MASTER is not set +CONFIG_GPIO_SYSFS=y # # Dallas's 1-wire bus @@ -820,6 +823,7 @@ CONFIG_LEDS_AMS_DELTA=y CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y # # Multimedia devices @@ -896,7 +900,13 @@ CONFIG_LOGO_LINUX_CLUT224=y # # Sound # -# CONFIG_SOUND is not set +CONFIG_SOUND=y +CONFIG_SND=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +CONFIG_SND_SOC=y +CONFIG_SND_OMAP_SOC=y +CONFIG_SND_OMAP_SOC_AMS_DELTA=y # # HID Devices -- cgit v1.2.3 From 24de042ca4faa5dc1811d7b6a8b6eefd97ed7577 Mon Sep 17 00:00:00 2001 From: Grazvydas Ignotas Date: Wed, 11 Nov 2009 11:00:35 -0800 Subject: omap3: pandora: Fix keypad keymap The original TWL4030 keypad driver from linux-omap used KEY() macro defined as (col, row), but while it was merged upstream it was changed to use matrix keypad infrastructure, which uses (row, col) format. Update the keymap in board file to match layout of mainline driver. Signed-off-by: Grazvydas Ignotas Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3pandora.c | 78 ++++++++++++++++---------------- 1 file changed, 39 insertions(+), 39 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 5326e0d61597..7519edb69155 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -134,50 +134,50 @@ static void __init pandora_keys_gpio_init(void) } static int board_keymap[] = { - /* col, row, code */ + /* row, col, code */ KEY(0, 0, KEY_9), - KEY(0, 1, KEY_0), - KEY(0, 2, KEY_BACKSPACE), - KEY(0, 3, KEY_O), - KEY(0, 4, KEY_P), - KEY(0, 5, KEY_K), - KEY(0, 6, KEY_L), - KEY(0, 7, KEY_ENTER), - KEY(1, 0, KEY_8), + KEY(0, 1, KEY_8), + KEY(0, 2, KEY_I), + KEY(0, 3, KEY_J), + KEY(0, 4, KEY_N), + KEY(0, 5, KEY_M), + KEY(1, 0, KEY_0), KEY(1, 1, KEY_7), - KEY(1, 2, KEY_6), - KEY(1, 3, KEY_5), - KEY(1, 4, KEY_4), - KEY(1, 5, KEY_3), - KEY(1, 6, KEY_2), - KEY(1, 7, KEY_1), - KEY(2, 0, KEY_I), - KEY(2, 1, KEY_U), + KEY(1, 2, KEY_U), + KEY(1, 3, KEY_H), + KEY(1, 4, KEY_B), + KEY(1, 5, KEY_SPACE), + KEY(2, 0, KEY_BACKSPACE), + KEY(2, 1, KEY_6), KEY(2, 2, KEY_Y), - KEY(2, 3, KEY_T), - KEY(2, 4, KEY_R), - KEY(2, 5, KEY_E), - KEY(2, 6, KEY_W), - KEY(2, 7, KEY_Q), - KEY(3, 0, KEY_J), - KEY(3, 1, KEY_H), - KEY(3, 2, KEY_G), + KEY(2, 3, KEY_G), + KEY(2, 4, KEY_V), + KEY(2, 5, KEY_FN), + KEY(3, 0, KEY_O), + KEY(3, 1, KEY_5), + KEY(3, 2, KEY_T), KEY(3, 3, KEY_F), - KEY(3, 4, KEY_D), - KEY(3, 5, KEY_S), - KEY(3, 6, KEY_A), - KEY(3, 7, KEY_LEFTSHIFT), - KEY(4, 0, KEY_N), - KEY(4, 1, KEY_B), - KEY(4, 2, KEY_V), - KEY(4, 3, KEY_C), + KEY(3, 4, KEY_C), + KEY(4, 0, KEY_P), + KEY(4, 1, KEY_4), + KEY(4, 2, KEY_R), + KEY(4, 3, KEY_D), KEY(4, 4, KEY_X), - KEY(4, 5, KEY_Z), - KEY(4, 6, KEY_DOT), - KEY(4, 7, KEY_COMMA), - KEY(5, 0, KEY_M), - KEY(5, 1, KEY_SPACE), - KEY(5, 2, KEY_FN), + KEY(5, 0, KEY_K), + KEY(5, 1, KEY_3), + KEY(5, 2, KEY_E), + KEY(5, 3, KEY_S), + KEY(5, 4, KEY_Z), + KEY(6, 0, KEY_L), + KEY(6, 1, KEY_2), + KEY(6, 2, KEY_W), + KEY(6, 3, KEY_A), + KEY(6, 4, KEY_DOT), + KEY(7, 0, KEY_ENTER), + KEY(7, 1, KEY_1), + KEY(7, 2, KEY_Q), + KEY(7, 3, KEY_LEFTSHIFT), + KEY(7, 4, KEY_COMMA), }; static struct matrix_keymap_data board_map_data = { -- cgit v1.2.3 From e9840dc00468c4d2ca63b9f80038533d0f931d16 Mon Sep 17 00:00:00 2001 From: Jarkko Nikula Date: Wed, 11 Nov 2009 11:00:36 -0800 Subject: omap3: beagle: Fix USB host port power control The host port power is enabled by driving the nEN_USB_PWR low as stated in the comment. This fix is originally from Steve Sakoman . Signed-off-by: Jarkko Nikula Cc: Steve Sakoman Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3beagle.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 70df6b4dbcd4..08b0816afa61 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -162,7 +162,7 @@ static int beagle_twl_gpio_setup(struct device *dev, /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */ gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR"); - gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1); + gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0); /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; -- cgit v1.2.3 From b30dcf5f37023d591caee80c233bf33706bc5a21 Mon Sep 17 00:00:00 2001 From: Sergio Aguirre Date: Wed, 11 Nov 2009 11:00:37 -0800 Subject: omap3: 3430sdp: Enable Linux Regulator framework Some drivers have dependencies on this, and therefore should be enabled. Signed-off-by: Sergio Aguirre Signed-off-by: Tony Lindgren --- arch/arm/configs/omap_3430sdp_defconfig | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/omap_3430sdp_defconfig b/arch/arm/configs/omap_3430sdp_defconfig index 8a4a7e2ba87b..5a305f015307 100644 --- a/arch/arm/configs/omap_3430sdp_defconfig +++ b/arch/arm/configs/omap_3430sdp_defconfig @@ -1703,7 +1703,14 @@ CONFIG_RTC_DRV_TWL4030=y # on-CPU RTC drivers # # CONFIG_DMADEVICES is not set -# CONFIG_REGULATOR is not set +CONFIG_REGULATOR=y +# CONFIG_REGULATOR_DEBUG is not set +# CONFIG_REGULATOR_FIXED_VOLTAGE is not set +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set +# CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_REGULATOR_MAX1586 is not set +CONFIG_REGULATOR_TWL4030=y # CONFIG_UIO is not set # CONFIG_STAGING is not set -- cgit v1.2.3 From 1ea6e6652a63f5db18d753d6a2c963d966b6d9c2 Mon Sep 17 00:00:00 2001 From: Grazvydas Ignotas Date: Wed, 11 Nov 2009 11:00:38 -0800 Subject: omap3: update Pandora defconfig This patch updates defconfig to enable options needed to properly boot OMAP3 pandora board. It also enables MMC, OTG, GPIO LEDs, TWL4030 GPIO and sound drivers. Signed-off-by: Grazvydas Ignotas Signed-off-by: Tony Lindgren --- arch/arm/configs/omap3_pandora_defconfig | 49 ++++++++++++++++++++++++++++---- 1 file changed, 44 insertions(+), 5 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/configs/omap3_pandora_defconfig b/arch/arm/configs/omap3_pandora_defconfig index b54ad2e2da36..150deafb0a6a 100644 --- a/arch/arm/configs/omap3_pandora_defconfig +++ b/arch/arm/configs/omap3_pandora_defconfig @@ -611,7 +611,7 @@ CONFIG_INPUT_KEYBOARD=y # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set -# CONFIG_KEYBOARD_GPIO is not set +CONFIG_KEYBOARD_GPIO=y CONFIG_INPUT_MOUSE=y # CONFIG_MOUSE_PS2 is not set # CONFIG_MOUSE_SERIAL is not set @@ -634,7 +634,8 @@ CONFIG_TOUCHSCREEN_ADS7846=y # CONFIG_TOUCHSCREEN_TOUCHWIN is not set # CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set # CONFIG_TOUCHSCREEN_TOUCHIT213 is not set -# CONFIG_INPUT_MISC is not set +CONFIG_INPUT_MISC=y +CONFIG_INPUT_TWL4030_PWRBUTTON=y # # Hardware I/O ports @@ -834,7 +835,29 @@ CONFIG_DAB=y # # CONFIG_VGA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y -# CONFIG_SOUND is not set +CONFIG_SOUND=y +CONFIG_SOUND_OSS_CORE=y +CONFIG_SOUND_OSS_CORE_PRECLAIM=y +CONFIG_SND=y +CONFIG_SND_TIMER=y +CONFIG_SND_PCM=y +CONFIG_SND_JACK=y +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +CONFIG_SND_PCM_OSS_PLUGINS=y +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +CONFIG_SND_VERBOSE_PRINTK=y +CONFIG_SND_DRIVERS=y +CONFIG_SND_USB=y +CONFIG_SND_SOC=y +CONFIG_SND_OMAP_SOC=y +CONFIG_SND_OMAP_SOC_MCBSP=y +CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y +CONFIG_SND_SOC_I2C_AND_SPI=y +CONFIG_SND_SOC_TWL4030=y + CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set @@ -1020,7 +1043,13 @@ CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_MMC_SPI is not set # CONFIG_MEMSTICK is not set # CONFIG_ACCESSIBILITY is not set -# CONFIG_NEW_LEDS is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=y +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_GPIO_PLATFORM=y +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_DEFAULT_ON=y + CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y CONFIG_RTC_HCTOSYS=y @@ -1084,9 +1113,12 @@ CONFIG_RTC_DRV_TWL4030=y # on-CPU RTC drivers # # CONFIG_DMADEVICES is not set -# CONFIG_REGULATOR is not set # CONFIG_UIO is not set +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_REGULATOR_TWL4030=y + # # File systems # @@ -1407,3 +1439,10 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y + +# added by hand for now +CONFIG_KEYBOARD_TWL4030=y +CONFIG_USB_OTG_UTILS=y +CONFIG_TWL4030_USB=y +CONFIG_MMC_OMAP_HS=y + -- cgit v1.2.3 From b029839cf1f3aa095de73aa2acc241f1c65201ab Mon Sep 17 00:00:00 2001 From: Mike Turquette Date: Wed, 11 Nov 2009 11:00:38 -0800 Subject: omap3: Decrease cpufreq transition latency Adjust OMAP3 frequency transition latency from 10,000,000uS to a more reasonable 300,000uS. This causes ondemand and conservative governors to sample CPU load more often resulting in more responsive behavior. Tested on Android 2.6.29; using this value and conservative governor, CORE power consumption on Zoom2 was comparable to the old and unresponsive 10,000,000uS value while UI responsiveness was greatly improved. Signed-off-by: Mike Turquette Signed-off-by: Kevin Hilman Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/cpu-omap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/cpu-omap.c b/arch/arm/plat-omap/cpu-omap.c index 1868c0d8f9b5..341235c278ac 100644 --- a/arch/arm/plat-omap/cpu-omap.c +++ b/arch/arm/plat-omap/cpu-omap.c @@ -127,7 +127,7 @@ static int __init omap_cpu_init(struct cpufreq_policy *policy) } /* FIXME: what's the actual transition time? */ - policy->cpuinfo.transition_latency = 10 * 1000 * 1000; + policy->cpuinfo.transition_latency = 300 * 1000; return 0; } -- cgit v1.2.3 From b2b36316626f0d6b92c3675a2aa2726efc71d146 Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Thu, 5 Nov 2009 08:10:10 +0100 Subject: [ARM] pxa: fix interrupts number calculation when CONFIG_PXA_HAVE_ISA_IRQS=y Commit d2c37068429b29d6549cf3486fc84b836689e122 ([ARM] pxa: initialize default interrupt priority and use ICHP for IRQ handling) broke ISA interrupt support on pxa27x/3xx. In such a case, PXA_IRQ(0) != 0, and the IRQ number computed from ICHP must be offset by PXA_IRQ(0). Tested on an Arcom Zeus (pxa270), with both CONFIG_PXA_HAVE_ISA_IRQS enabled and disabled. Signed-off-by: Marc Zyngier Tested-by: Haojian Zhuang Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/entry-macro.S | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/include/mach/entry-macro.S b/arch/arm/mach-pxa/include/mach/entry-macro.S index 241880608ac6..a73bc86a3c26 100644 --- a/arch/arm/mach-pxa/include/mach/entry-macro.S +++ b/arch/arm/mach-pxa/include/mach/entry-macro.S @@ -46,5 +46,6 @@ beq 1001f bic \irqstat, \irqstat, #0x80000000 mov \irqnr, \irqstat, lsr #16 + add \irqnr, \irqnr, #(PXA_IRQ(0)) 1001: .endm -- cgit v1.2.3 From 2b5e080ae946b4a346b842a73d80f319b7a6453c Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Wed, 21 Oct 2009 13:25:50 +0200 Subject: [ARM] pxa: fix missing underscores in mfp-pxa910.h Underscores were missing. Signed-off-by: Roel Kluin Signed-off-by: Eric Miao --- arch/arm/mach-mmp/include/mach/mfp-pxa910.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-mmp/include/mach/mfp-pxa910.h b/arch/arm/mach-mmp/include/mach/mfp-pxa910.h index bf1189ff9a34..7e8a80f25ddc 100644 --- a/arch/arm/mach-mmp/include/mach/mfp-pxa910.h +++ b/arch/arm/mach-mmp/include/mach/mfp-pxa910.h @@ -160,7 +160,7 @@ #define MMC1_WP_MMC1_WP MFP_CFG_DRV(MMC1_WP, AF0, MEDIUM) /* PWM */ -#define GPIO27 PWM3 AF2 MFP_CFG(GPIO27, AF2) +#define GPIO27_PWM3_AF2 MFP_CFG(GPIO27, AF2) #define GPIO51_PWM2_OUT MFP_CFG(GPIO51, AF2) #define GPIO117_PWM1_OUT MFP_CFG(GPIO117, AF2) #define GPIO118_PWM2_OUT MFP_CFG(GPIO118, AF2) -- cgit v1.2.3 From 15f593cfcb1178f832aaf9ec0200acd8c3c3348c Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Sun, 8 Nov 2009 03:05:11 +0100 Subject: [ARM] pxa/colibri: fix AC97 ifdefs and add missing include The AC97 part wasn't initialized on Colibri/PXA320 because the macros were wrong. Also, the code didn't compile because of a header file not being included. Signed-off-by: Marek Vasut Signed-off-by: Eric Miao --- arch/arm/mach-pxa/colibri-pxa320.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/colibri-pxa320.c b/arch/arm/mach-pxa/colibri-pxa320.c index 494572825c7d..ec0e14b96682 100644 --- a/arch/arm/mach-pxa/colibri-pxa320.c +++ b/arch/arm/mach-pxa/colibri-pxa320.c @@ -27,6 +27,7 @@ #include #include #include +#include #include "generic.h" #include "devices.h" @@ -145,7 +146,8 @@ static void __init colibri_pxa320_init_lcd(void) static inline void colibri_pxa320_init_lcd(void) {} #endif -#if defined(SND_AC97_CODEC) || defined(SND_AC97_CODEC_MODULE) +#if defined(CONFIG_SND_AC97_CODEC) || \ + defined(CONFIG_SND_AC97_CODEC_MODULE) static mfp_cfg_t colibri_pxa320_ac97_pin_config[] __initdata = { GPIO34_AC97_SYSCLK, GPIO35_AC97_SDATA_IN_0, -- cgit v1.2.3 From 9da4ea69f28cf2bd20be86eda34afbc03c2180c7 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 13 Nov 2009 16:44:14 +0800 Subject: [ARM] pxa: fix incorrect mfp_to_gpio() conversion Since MFP_PIN_GPIO* now includes 128-255, mfp_to_gpio() is no longer valid for those additional pins, fix it. Signed-off-by: Eric Miao --- arch/arm/plat-pxa/include/plat/mfp.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-pxa/include/plat/mfp.h b/arch/arm/plat-pxa/include/plat/mfp.h index 22086e696e8e..857a6839071c 100644 --- a/arch/arm/plat-pxa/include/plat/mfp.h +++ b/arch/arm/plat-pxa/include/plat/mfp.h @@ -16,7 +16,7 @@ #ifndef __ASM_PLAT_MFP_H #define __ASM_PLAT_MFP_H -#define mfp_to_gpio(m) ((m) % 128) +#define mfp_to_gpio(m) ((m) % 256) /* list of all the configurable MFP pins */ enum { -- cgit v1.2.3 From 2bf30108435339c4cf149f9d279d0dc961345393 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Thu, 12 Nov 2009 20:31:14 +0100 Subject: [ARM] Kirkwood: disable propagation of mbus error to the CPU local bus Disable propagation of mbus errors to the CPU local bus, as this causes mbus errors (which can occur for example for PCI aborts) to throw CPU aborts, which we're not set up to deal with. Reported-by: Dieter Kiermaier Signed-off-by: Lennert Buytenhek Signed-off-by: Nicolas Pitre --- arch/arm/mach-kirkwood/common.c | 8 ++++++++ arch/arm/mach-kirkwood/include/mach/bridge-regs.h | 3 +++ 2 files changed, 11 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c index 7177c4aa6342..242dd0775343 100644 --- a/arch/arm/mach-kirkwood/common.c +++ b/arch/arm/mach-kirkwood/common.c @@ -915,6 +915,14 @@ void __init kirkwood_init(void) kirkwood_uart0_data[0].uartclk = kirkwood_tclk; kirkwood_uart1_data[0].uartclk = kirkwood_tclk; + /* + * Disable propagation of mbus errors to the CPU local bus, + * as this causes mbus errors (which can occur for example + * for PCI aborts) to throw CPU aborts, which we're not set + * up to deal with. + */ + writel(readl(CPU_CONFIG) & ~CPU_CONFIG_ERROR_PROP, CPU_CONFIG); + kirkwood_setup_cpu_mbus(); #ifdef CONFIG_CACHE_FEROCEON_L2 diff --git a/arch/arm/mach-kirkwood/include/mach/bridge-regs.h b/arch/arm/mach-kirkwood/include/mach/bridge-regs.h index 9e80d9232c83..418f5017c50e 100644 --- a/arch/arm/mach-kirkwood/include/mach/bridge-regs.h +++ b/arch/arm/mach-kirkwood/include/mach/bridge-regs.h @@ -13,6 +13,9 @@ #include +#define CPU_CONFIG (BRIDGE_VIRT_BASE | 0x0100) +#define CPU_CONFIG_ERROR_PROP 0x00000004 + #define CPU_CONTROL (BRIDGE_VIRT_BASE | 0x0104) #define CPU_RESET 0x00000002 -- cgit v1.2.3 From 0f74296a0f818d8ae52d9b77ec531e8dd804dda3 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 20 Oct 2009 16:32:53 +0200 Subject: at91: at91sam9g20ek modify dual slot evaluation kit at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the previous dual slot board definition to match the official rev. C board. It also allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one. Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC slot A. This lead to a modification of those definitions. Signed-off-by: Nicolas Ferre Acked-by: Andrew Victor --- arch/arm/mach-at91/Kconfig | 20 +++++++++++--------- arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c | 23 +++++++++++++++-------- 2 files changed, 26 insertions(+), 17 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index e35d54d43e70..2fd88437348b 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -289,13 +289,6 @@ config MACH_NEOCORE926 help Select this if you are using the Adeneo Neocore 926 board. -config MACH_AT91SAM9G20EK_2MMC - bool "Atmel AT91SAM9G20-EK Evaluation Kit modified for 2 MMC Slots" - depends on ARCH_AT91SAM9G20 - help - Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit - Rev A or B modified for 2 MMC Slots. - endif # ---------------------------------------------------------- @@ -322,7 +315,16 @@ config MACH_AT91SAM9G20EK bool "Atmel AT91SAM9G20-EK Evaluation Kit" depends on ARCH_AT91SAM9G20 help - Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit. + Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit + that embeds only one SD/MMC slot. + +config MACH_AT91SAM9G20EK_2MMC + bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots" + depends on ARCH_AT91SAM9G20 + help + Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit + with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and + onwards. config MACH_CPU9G20 bool "Eukrea CPU9G20 board" @@ -392,7 +394,7 @@ config MTD_AT91_DATAFLASH_CARD config MTD_NAND_ATMEL_BUSWIDTH_16 bool "Enable 16-bit data bus interface to NAND flash" - depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK) + depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G20EK_2MMC || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK) help On AT91SAM926x boards both types of NAND flash can be present (8 and 16 bit data bus width). diff --git a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c index a28e53faf71d..a4102d72cc9b 100644 --- a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c +++ b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c @@ -90,7 +90,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_ATMELMCI) +#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -113,7 +113,7 @@ static struct spi_board_info ek_spi_devices[] = { * MACB Ethernet device */ static struct at91_eth_data __initdata ek_macb_data = { - .phy_irq_pin = AT91_PIN_PC12, + .phy_irq_pin = AT91_PIN_PB0, .is_rmii = 1, }; @@ -194,24 +194,27 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) - * det_pin and wp_pin are not connected + * wp_pin is not connected */ #if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) static struct mci_platform_data __initdata ek_mmc_data = { .slot[0] = { .bus_width = 4, - .detect_pin = -ENODEV, + .detect_pin = AT91_PIN_PC2, .wp_pin = -ENODEV, }, .slot[1] = { .bus_width = 4, - .detect_pin = -ENODEV, + .detect_pin = AT91_PIN_PC9, .wp_pin = -ENODEV, }, }; #else -static struct amci_platform_data __initdata ek_mmc_data = { +static struct at91_mmc_data __initdata ek_mmc_data = { + .slot_b = 1, /* Only one slot so use slot B */ + .wire4 = 1, + .det_pin = AT91_PIN_PC9, }; #endif @@ -221,13 +224,13 @@ static struct amci_platform_data __initdata ek_mmc_data = { static struct gpio_led ek_leds[] = { { /* "bottom" led, green, userled1 to be defined */ .name = "ds5", - .gpio = AT91_PIN_PB12, + .gpio = AT91_PIN_PB8, .active_low = 1, .default_trigger = "none", }, { /* "power" led, yellow */ .name = "ds1", - .gpio = AT91_PIN_PB13, + .gpio = AT91_PIN_PB9, .default_trigger = "heartbeat", } }; @@ -254,7 +257,11 @@ static void __init ek_board_init(void) /* Ethernet */ at91_add_device_eth(&ek_macb_data); /* MMC */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) at91_add_device_mci(0, &ek_mmc_data); +#else + at91_add_device_mmc(0, &ek_mmc_data); +#endif /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* LEDs */ -- cgit v1.2.3 From 378ce74bee4cb0183489bc0f850790a2264ca975 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Sat, 14 Nov 2009 01:03:24 +0100 Subject: ARM: 5787/1: U300 COH 901 331 fixes This will fix some small issues with the COH 901 331 RTC driver: - Interrupt is disabled after alarm so that we don't fire multiple interrupts. - We return 0 from the coh901331_alarm_irq_enable() ridding a compile warning. - We alter the name in the U300 device registry to match that of the driver so they sucessfully resolve. Signed-off-by: Linus Walleij Signed-off-by: Russell King --- arch/arm/mach-u300/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index be60d6deee8b..653e25be3dd8 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -408,7 +408,7 @@ static struct platform_device keypad_device = { }; static struct platform_device rtc_device = { - .name = "rtc0", + .name = "rtc-coh901331", .id = -1, .num_resources = ARRAY_SIZE(rtc_resources), .resource = rtc_resources, -- cgit v1.2.3 From 10d5d99e880692a31ddc59b9f5d063e928fc0c89 Mon Sep 17 00:00:00 2001 From: Paul Parsons Date: Sat, 14 Nov 2009 16:54:12 +0000 Subject: [ARM] pxa/hx4700: fix hx4700 touchscreen pressure values hx4700 touchscreen events were being dropped in ads7846_rx() because their pressure values consistently exceeded the platform maximum of 512; a sample of 256 pressure values were in the range 531 to 815. Doubling the platform maximum to 1024 allows hx4700 touchscreen events to pass the test. Signed-off-by: Paul Parsons Signed-off-by: Eric Miao --- arch/arm/mach-pxa/hx4700.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c index abff9e132749..83bd3c6e3884 100644 --- a/arch/arm/mach-pxa/hx4700.c +++ b/arch/arm/mach-pxa/hx4700.c @@ -604,7 +604,7 @@ static struct platform_device gpio_vbus = { static const struct ads7846_platform_data tsc2046_info = { .model = 7846, .vref_delay_usecs = 100, - .pressure_max = 512, + .pressure_max = 1024, .debounce_max = 10, .debounce_tol = 3, .debounce_rep = 1, -- cgit v1.2.3 From 7df56c2586049a06b007474ca059779c81ddb1ff Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Fri, 13 Nov 2009 11:37:34 +0100 Subject: [ARM] pxa: ensure mfp is in correct range in mfp_{read,write} Ensure we do not read/write outside array boundaries with a negative index. Signed-off-by: Roel Kluin Signed-off-by: Eric Miao --- arch/arm/plat-pxa/mfp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-pxa/mfp.c b/arch/arm/plat-pxa/mfp.c index 9405d0379c85..be58f9fe65b0 100644 --- a/arch/arm/plat-pxa/mfp.c +++ b/arch/arm/plat-pxa/mfp.c @@ -207,7 +207,7 @@ unsigned long mfp_read(int mfp) { unsigned long val, flags; - BUG_ON(mfp >= MFP_PIN_MAX); + BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX); spin_lock_irqsave(&mfp_spin_lock, flags); val = mfpr_readl(mfp_table[mfp].mfpr_off); @@ -220,7 +220,7 @@ void mfp_write(int mfp, unsigned long val) { unsigned long flags; - BUG_ON(mfp >= MFP_PIN_MAX); + BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX); spin_lock_irqsave(&mfp_spin_lock, flags); mfpr_writel(mfp_table[mfp].mfpr_off, val); -- cgit v1.2.3 From f7343deb0f6e7654c60e97606aea388b9da612c2 Mon Sep 17 00:00:00 2001 From: Vimal Singh Date: Mon, 16 Nov 2009 14:55:59 -0800 Subject: omap: Fix keymap for zoom2 according to matrix keypad framwork Interpretation of 'row' and 'col' got reversed in matrix keymap framework. Also last element '0', present in keymap array, is no more needed. Correcting zoom2 keyboard keymap accordingly. Signed-off-by: Vimal Singh Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-zoom2.c | 87 +++++++++++++++++++-------------------- 1 file changed, 43 insertions(+), 44 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c index ea00486a5e53..51e0b3ba5f3a 100644 --- a/arch/arm/mach-omap2/board-zoom2.c +++ b/arch/arm/mach-omap2/board-zoom2.c @@ -30,57 +30,56 @@ /* Zoom2 has Qwerty keyboard*/ static int board_keymap[] = { KEY(0, 0, KEY_E), - KEY(1, 0, KEY_R), - KEY(2, 0, KEY_T), - KEY(3, 0, KEY_HOME), - KEY(6, 0, KEY_I), - KEY(7, 0, KEY_LEFTSHIFT), - KEY(0, 1, KEY_D), + KEY(0, 1, KEY_R), + KEY(0, 2, KEY_T), + KEY(0, 3, KEY_HOME), + KEY(0, 6, KEY_I), + KEY(0, 7, KEY_LEFTSHIFT), + KEY(1, 0, KEY_D), KEY(1, 1, KEY_F), - KEY(2, 1, KEY_G), - KEY(3, 1, KEY_SEND), - KEY(6, 1, KEY_K), - KEY(7, 1, KEY_ENTER), - KEY(0, 2, KEY_X), - KEY(1, 2, KEY_C), + KEY(1, 2, KEY_G), + KEY(1, 3, KEY_SEND), + KEY(1, 6, KEY_K), + KEY(1, 7, KEY_ENTER), + KEY(2, 0, KEY_X), + KEY(2, 1, KEY_C), KEY(2, 2, KEY_V), - KEY(3, 2, KEY_END), - KEY(6, 2, KEY_DOT), - KEY(7, 2, KEY_CAPSLOCK), - KEY(0, 3, KEY_Z), - KEY(1, 3, KEY_KPPLUS), - KEY(2, 3, KEY_B), + KEY(2, 3, KEY_END), + KEY(2, 6, KEY_DOT), + KEY(2, 7, KEY_CAPSLOCK), + KEY(3, 0, KEY_Z), + KEY(3, 1, KEY_KPPLUS), + KEY(3, 2, KEY_B), KEY(3, 3, KEY_F1), - KEY(6, 3, KEY_O), - KEY(7, 3, KEY_SPACE), - KEY(0, 4, KEY_W), - KEY(1, 4, KEY_Y), - KEY(2, 4, KEY_U), - KEY(3, 4, KEY_F2), + KEY(3, 6, KEY_O), + KEY(3, 7, KEY_SPACE), + KEY(4, 0, KEY_W), + KEY(4, 1, KEY_Y), + KEY(4, 2, KEY_U), + KEY(4, 3, KEY_F2), KEY(4, 4, KEY_VOLUMEUP), - KEY(6, 4, KEY_L), - KEY(7, 4, KEY_LEFT), - KEY(0, 5, KEY_S), - KEY(1, 5, KEY_H), - KEY(2, 5, KEY_J), - KEY(3, 5, KEY_F3), + KEY(4, 6, KEY_L), + KEY(4, 7, KEY_LEFT), + KEY(5, 0, KEY_S), + KEY(5, 1, KEY_H), + KEY(5, 2, KEY_J), + KEY(5, 3, KEY_F3), KEY(5, 5, KEY_VOLUMEDOWN), - KEY(6, 5, KEY_M), - KEY(4, 5, KEY_ENTER), - KEY(7, 5, KEY_RIGHT), - KEY(0, 6, KEY_Q), - KEY(1, 6, KEY_A), - KEY(2, 6, KEY_N), - KEY(3, 6, KEY_BACKSPACE), + KEY(5, 6, KEY_M), + KEY(5, 7, KEY_ENTER), + KEY(6, 0, KEY_Q), + KEY(6, 1, KEY_A), + KEY(6, 2, KEY_N), + KEY(6, 3, KEY_BACKSPACE), KEY(6, 6, KEY_P), - KEY(7, 6, KEY_UP), KEY(6, 7, KEY_SELECT), - KEY(7, 7, KEY_DOWN), - KEY(0, 7, KEY_PROG1), /*MACRO 1 */ - KEY(1, 7, KEY_PROG2), /*MACRO 2 */ - KEY(2, 7, KEY_PROG3), /*MACRO 3 */ - KEY(3, 7, KEY_PROG4), /*MACRO 4 */ - 0 + KEY(7, 0, KEY_PROG1), /*MACRO 1 */ + KEY(7, 1, KEY_PROG2), /*MACRO 2 */ + KEY(7, 2, KEY_PROG3), /*MACRO 3 */ + KEY(7, 3, KEY_PROG4), /*MACRO 4 */ + KEY(7, 5, KEY_RIGHT), + KEY(7, 6, KEY_UP), + KEY(7, 7, KEY_DOWN) }; static struct matrix_keymap_data board_map_data = { -- cgit v1.2.3 From 9346f48b26a4b48a7d56314bbb94e6b801e28316 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Mon, 16 Nov 2009 13:36:53 +0000 Subject: omap3: clock: Fix the DPLL freqsel computations Fix the freqsel value computation. Use n instead of (n+1) The formula in the TRM uses a zero-based N, hence the (n+1); however at this point in the clock34xx.c code, N is one-based. Hayati Bayrakdar and Nishanth Menon helped track down this bug. Signed-off-by: Rajendra Nayak Signed-off-by: Paul Walmsley [paul@pwsan.com: modified commit message] Cc: Hayati Bayrakdar Cc: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/clock34xx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 489556eecbd1..7c5c00df3c70 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -473,7 +473,7 @@ static u16 _omap3_dpll_compute_freqsel(struct clk *clk, u8 n) unsigned long fint; u16 f = 0; - fint = clk->dpll_data->clk_ref->rate / (n + 1); + fint = clk->dpll_data->clk_ref->rate / n; pr_debug("clock: fint is %lu\n", fint); -- cgit v1.2.3 From 72f962fc7bc00f5ff4991912b889f87b464f7f1a Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 16 Nov 2009 13:36:54 +0000 Subject: omap3: clock: Fixed dpll3_m2x2 rate calculation Current calculation does not take into account any changes to M2 divisor, and thus when we change VDD2 OPP, dpll3_m2x2 rate does not change. Fixed by re-routing dpll3_m2x2 parent to dpll3_m2. Signed-off-by: Tero Kristo Signed-off-by: Paul Walmsley Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/clock34xx.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h index c8119781e00a..9565c05bebd2 100644 --- a/arch/arm/mach-omap2/clock34xx.h +++ b/arch/arm/mach-omap2/clock34xx.h @@ -489,9 +489,9 @@ static struct clk core_ck = { static struct clk dpll3_m2x2_ck = { .name = "dpll3_m2x2_ck", .ops = &clkops_null, - .parent = &dpll3_x2_ck, + .parent = &dpll3_m2_ck, .clkdm_name = "dpll3_clkdm", - .recalc = &followparent_recalc, + .recalc = &omap3_clkoutx2_recalc, }; /* The PWRDN bit is apparently only available on 3430ES2 and above */ -- cgit v1.2.3 From d32b20fc7dad87ac95fcc73fca3606c0db85f210 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Tue, 17 Nov 2009 14:39:03 -0800 Subject: omap: fix unlikely(x) < y The closing parenthesis was not in the right location. Signed-off-by: Roel Kluin Cc: Russell King Signed-off-by: Tony Lindgren Signed-off-by: Andrew Morton --- arch/arm/plat-omap/gpio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index 71ebd7fcfea1..7c345b757df1 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -373,7 +373,7 @@ static inline int gpio_valid(int gpio) static int check_gpio(int gpio) { - if (unlikely(gpio_valid(gpio)) < 0) { + if (unlikely(gpio_valid(gpio) < 0)) { printk(KERN_ERR "omap-gpio: invalid GPIO %d\n", gpio); dump_stack(); return -1; -- cgit v1.2.3 From e7fdc6052e78738ce90e0bdc051f2ddf60e41324 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Tue, 17 Nov 2009 14:39:06 -0800 Subject: OMAP: cs should be positive in gpmc_cs_free() The index `cs' is signed, test whether it is negative before we release gpmc_cs_mem[cs]. Signed-off-by: Roel Kluin Cc: Russell King Signed-off-by: Tony Lindgren Signed-off-by: Andrew Morton --- arch/arm/mach-omap2/gpmc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index f8657568b1ba..f3c992e29651 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -378,7 +378,7 @@ EXPORT_SYMBOL(gpmc_cs_request); void gpmc_cs_free(int cs) { spin_lock(&gpmc_mem_lock); - if (cs >= GPMC_CS_NUM || !gpmc_cs_reserved(cs)) { + if (cs >= GPMC_CS_NUM || cs < 0 || !gpmc_cs_reserved(cs)) { printk(KERN_ERR "Trying to free non-reserved GPMC CS%d\n", cs); BUG(); spin_unlock(&gpmc_mem_lock); -- cgit v1.2.3 From 4ff1fa278b0bd1b2dd3c42efc0cb86788ffe05d5 Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 18 Nov 2009 18:03:19 +0000 Subject: [ARM] kmap: fix build errors with DEBUG_HIGHMEM enabled d451564 broke ARM by requiring KM_IRQ_PTE, KM_NMI and KM_NMI_PTE to always be defined. Solve this by providing invalid definitions for these constants, but only if CONFIG_DEBUG_HIGHMEM is enabled. Signed-off-by: Russell King --- arch/arm/include/asm/kmap_types.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/include/asm/kmap_types.h b/arch/arm/include/asm/kmap_types.h index d16ec97ec9a9..c019949a5189 100644 --- a/arch/arm/include/asm/kmap_types.h +++ b/arch/arm/include/asm/kmap_types.h @@ -22,4 +22,10 @@ enum km_type { KM_TYPE_NR }; +#ifdef CONFIG_DEBUG_HIGHMEM +#define KM_NMI (-1) +#define KM_NMI_PTE (-1) +#define KM_IRQ_PTE (-1) +#endif + #endif -- cgit v1.2.3 From 68a31de302bae12010ab116752d4362bd7fe2851 Mon Sep 17 00:00:00 2001 From: Daniel Mack Date: Fri, 20 Nov 2009 17:50:34 +0100 Subject: [ARM] pxa/cpufreq: fix index assignments for end marker I stumbled over two small things regarding the .index field assignment in the dynamically created cpu frequency tables for pxa2xx and pxa3xx. Even though that doesn't currently cause any problem, it should still be fixed in case the logic in the CPUFREQ core changes. Signed-off-by: Daniel Mack Signed-off-by: Eric Miao --- arch/arm/mach-pxa/cpufreq-pxa2xx.c | 1 + arch/arm/mach-pxa/cpufreq-pxa3xx.c | 2 +- 2 files changed, 2 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/cpufreq-pxa2xx.c b/arch/arm/mach-pxa/cpufreq-pxa2xx.c index 983cc8c20081..9e4d9816726a 100644 --- a/arch/arm/mach-pxa/cpufreq-pxa2xx.c +++ b/arch/arm/mach-pxa/cpufreq-pxa2xx.c @@ -447,6 +447,7 @@ static __init int pxa_cpufreq_init(struct cpufreq_policy *policy) pxa27x_freq_table[i].frequency = freq; pxa27x_freq_table[i].index = i; } + pxa27x_freq_table[i].index = i; pxa27x_freq_table[i].frequency = CPUFREQ_TABLE_END; /* diff --git a/arch/arm/mach-pxa/cpufreq-pxa3xx.c b/arch/arm/mach-pxa/cpufreq-pxa3xx.c index 67f34a8d8e60..149cdd9aee4d 100644 --- a/arch/arm/mach-pxa/cpufreq-pxa3xx.c +++ b/arch/arm/mach-pxa/cpufreq-pxa3xx.c @@ -102,7 +102,7 @@ static int setup_freqs_table(struct cpufreq_policy *policy, table[i].index = i; table[i].frequency = freqs[i].cpufreq_mhz * 1000; } - table[num].frequency = i; + table[num].index = i; table[num].frequency = CPUFREQ_TABLE_END; pxa3xx_freqs = freqs; -- cgit v1.2.3 From 81065518eda14ebbce1b48c98d5077b0a059d4a3 Mon Sep 17 00:00:00 2001 From: Pavel Machek Date: Wed, 18 Nov 2009 10:01:00 +0100 Subject: [ARM] pxa/spitz: fix compile regression on spitz If CONFIG_AKITA is not set, spitz fails to compile. It worked ok in rc5. Fix is one more ifdef... Signed-off-by: Pavel Machek Acked-by: Stanislav Brabec Signed-off-by: Eric Miao --- arch/arm/mach-pxa/spitz.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index 3da45d051743..d98023f55503 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -802,10 +802,12 @@ static void __init spitz_init(void) { spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON; +#ifdef CONFIG_MACH_BORZOI if (machine_is_borzoi()) { sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt; sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo; } +#endif platform_scoop_config = &spitz_pcmcia_config; -- cgit v1.2.3 From 3336f4f08e0dad7a2b6493c80b49b685141d53ad Mon Sep 17 00:00:00 2001 From: Jean PIHET Date: Mon, 23 Nov 2009 17:03:32 +0100 Subject: ARM: 5793/1: ARM: Check put_user fail in do_signal when enable OABI_COMPAT Using OABI, the call to put_user in do_signal can fail causing the calling app to hang. The solution is to check if put_user fails and force the app to seg fault in that case. Tested with multiple sleeping apps/threads (using the nanosleep syscall) and suspend/resume. Signed-off-by: janboe Signed-off-by: Jean Pihet Signed-off-by: Russell King --- arch/arm/kernel/signal.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c index 2a573d4fea24..e7714f367eb8 100644 --- a/arch/arm/kernel/signal.c +++ b/arch/arm/kernel/signal.c @@ -662,8 +662,12 @@ static void do_signal(struct pt_regs *regs, int syscall) regs->ARM_sp -= 4; usp = (u32 __user *)regs->ARM_sp; - put_user(regs->ARM_pc, usp); - regs->ARM_pc = KERN_RESTART_CODE; + if (put_user(regs->ARM_pc, usp) == 0) { + regs->ARM_pc = KERN_RESTART_CODE; + } else { + regs->ARM_sp += 4; + force_sigsegv(0, current); + } #endif } } -- cgit v1.2.3 From 9faf3c1d0dab9e9f4b0cbd42bc37be515d8b8cb1 Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 25 Nov 2009 22:14:59 +0000 Subject: [ARM] Update mach-types Signed-off-by: Russell King --- arch/arm/tools/mach-types | 119 +++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 117 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 94be7bb6cb9a..07b976da6174 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Fri Sep 18 21:42:00 2009 +# Last update: Wed Nov 25 22:14:58 2009 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -928,7 +928,7 @@ palmt5 MACH_PALMT5 PALMT5 917 palmtc MACH_PALMTC PALMTC 918 omap_apollon MACH_OMAP_APOLLON OMAP_APOLLON 919 mxc30030evb MACH_MXC30030EVB MXC30030EVB 920 -rea_2d MACH_REA_2D REA_2D 921 +rea_cpu2 MACH_REA_2D REA_2D 921 eti3e524 MACH_TI3E524 TI3E524 922 ateb9200 MACH_ATEB9200 ATEB9200 923 auckland MACH_AUCKLAND AUCKLAND 924 @@ -2421,3 +2421,118 @@ liberty MACH_LIBERTY LIBERTY 2434 mh355 MACH_MH355 MH355 2435 pc7802 MACH_PC7802 PC7802 2436 gnet_sgc MACH_GNET_SGC GNET_SGC 2437 +einstein15 MACH_EINSTEIN15 EINSTEIN15 2438 +cmpd MACH_CMPD CMPD 2439 +davinci_hase1 MACH_DAVINCI_HASE1 DAVINCI_HASE1 2440 +lgeincitephone MACH_LGEINCITEPHONE LGEINCITEPHONE 2441 +ea313x MACH_EA313X EA313X 2442 +fwbd_39064 MACH_FWBD_39064 FWBD_39064 2443 +fwbd_390128 MACH_FWBD_390128 FWBD_390128 2444 +pelco_moe MACH_PELCO_MOE PELCO_MOE 2445 +minimix27 MACH_MINIMIX27 MINIMIX27 2446 +omap3_thunder MACH_OMAP3_THUNDER OMAP3_THUNDER 2447 +passionc MACH_PASSIONC PASSIONC 2448 +mx27amata MACH_MX27AMATA MX27AMATA 2449 +bgat1 MACH_BGAT1 BGAT1 2450 +buzz MACH_BUZZ BUZZ 2451 +mb9g20 MACH_MB9G20 MB9G20 2452 +yushan MACH_YUSHAN YUSHAN 2453 +lizard MACH_LIZARD LIZARD 2454 +omap3polycom MACH_OMAP3POLYCOM OMAP3POLYCOM 2455 +smdkv210 MACH_SMDKV210 SMDKV210 2456 +bravo MACH_BRAVO BRAVO 2457 +siogentoo1 MACH_SIOGENTOO1 SIOGENTOO1 2458 +siogentoo2 MACH_SIOGENTOO2 SIOGENTOO2 2459 +sm3k MACH_SM3K SM3K 2460 +acer_tempo_f900 MACH_ACER_TEMPO_F900 ACER_TEMPO_F900 2461 +sst61vc010_dev MACH_SST61VC010_DEV SST61VC010_DEV 2462 +glittertind MACH_GLITTERTIND GLITTERTIND 2463 +omap_zoom3 MACH_OMAP_ZOOM3 OMAP_ZOOM3 2464 +omap_3630sdp MACH_OMAP_3630SDP OMAP_3630SDP 2465 +cybook2440 MACH_CYBOOK2440 CYBOOK2440 2466 +torino_s MACH_TORINO_S TORINO_S 2467 +havana MACH_HAVANA HAVANA 2468 +beaumont_11 MACH_BEAUMONT_11 BEAUMONT_11 2469 +vanguard MACH_VANGUARD VANGUARD 2470 +s5pc110_draco MACH_S5PC110_DRACO S5PC110_DRACO 2471 +cartesio_two MACH_CARTESIO_TWO CARTESIO_TWO 2472 +aster MACH_ASTER ASTER 2473 +voguesv210 MACH_VOGUESV210 VOGUESV210 2474 +acm500x MACH_ACM500X ACM500X 2475 +km9260 MACH_KM9260 KM9260 2476 +nideflexg1 MACH_NIDEFLEXG1 NIDEFLEXG1 2477 +ctera_plug_io MACH_CTERA_PLUG_IO CTERA_PLUG_IO 2478 +smartq7 MACH_SMARTQ7 SMARTQ7 2479 +at91sam9g10ek2 MACH_AT91SAM9G10EK2 AT91SAM9G10EK2 2480 +asusp527 MACH_ASUSP527 ASUSP527 2481 +at91sam9g20mpm2 MACH_AT91SAM9G20MPM2 AT91SAM9G20MPM2 2482 +topasa900 MACH_TOPASA900 TOPASA900 2483 +electrum_100 MACH_ELECTRUM_100 ELECTRUM_100 2484 +mx51grb MACH_MX51GRB MX51GRB 2485 +xea300 MACH_XEA300 XEA300 2486 +htcstartrek MACH_HTCSTARTREK HTCSTARTREK 2487 +lima MACH_LIMA LIMA 2488 +csb740 MACH_CSB740 CSB740 2489 +usb_s8815 MACH_USB_S8815 USB_S8815 2490 +watson_efm_plugin MACH_WATSON_EFM_PLUGIN WATSON_EFM_PLUGIN 2491 +milkyway MACH_MILKYWAY MILKYWAY 2492 +g4evm MACH_G4EVM G4EVM 2493 +picomod6 MACH_PICOMOD6 PICOMOD6 2494 +omapl138_hawkboard MACH_OMAPL138_HAWKBOARD OMAPL138_HAWKBOARD 2495 +ip6000 MACH_IP6000 IP6000 2496 +ip6010 MACH_IP6010 IP6010 2497 +utm400 MACH_UTM400 UTM400 2498 +omap3_zybex MACH_OMAP3_ZYBEX OMAP3_ZYBEX 2499 +wireless_space MACH_WIRELESS_SPACE WIRELESS_SPACE 2500 +sx560 MACH_SX560 SX560 2501 +ts41x MACH_TS41X TS41X 2502 +elphel10373 MACH_ELPHEL10373 ELPHEL10373 2503 +rhobot MACH_RHOBOT RHOBOT 2504 +mx51_refresh MACH_MX51_REFRESH MX51_REFRESH 2505 +ls9260 MACH_LS9260 LS9260 2506 +shank MACH_SHANK SHANK 2507 +qsd8x50_st1 MACH_QSD8X50_ST1 QSD8X50_ST1 2508 +at91sam9m10ekes MACH_AT91SAM9M10EKES AT91SAM9M10EKES 2509 +hiram MACH_HIRAM HIRAM 2510 +phy3250 MACH_PHY3250 PHY3250 2511 +ea3250 MACH_EA3250 EA3250 2512 +fdi3250 MACH_FDI3250 FDI3250 2513 +whitestone MACH_WHITESTONE WHITESTONE 2514 +at91sam9263nit MACH_AT91SAM9263NIT AT91SAM9263NIT 2515 +ccmx51 MACH_CCMX51 CCMX51 2516 +ccmx51js MACH_CCMX51JS CCMX51JS 2517 +ccwmx51 MACH_CCWMX51 CCWMX51 2518 +ccwmx51js MACH_CCWMX51JS CCWMX51JS 2519 +mini6410 MACH_MINI6410 MINI6410 2520 +tiny6410 MACH_TINY6410 TINY6410 2521 +nano6410 MACH_NANO6410 NANO6410 2522 +at572d940hfnldb MACH_AT572D940HFNLDB AT572D940HFNLDB 2523 +htcleo MACH_HTCLEO HTCLEO 2524 +avp13 MACH_AVP13 AVP13 2525 +xxsvideod MACH_XXSVIDEOD XXSVIDEOD 2526 +vpnext MACH_VPNEXT VPNEXT 2527 +swarco_itc3 MACH_SWARCO_ITC3 SWARCO_ITC3 2528 +tx51 MACH_TX51 TX51 2529 +dolby_cat1021 MACH_DOLBY_CAT1021 DOLBY_CAT1021 2530 +mx28evk MACH_MX28EVK MX28EVK 2531 +phoenix260 MACH_PHOENIX260 PHOENIX260 2532 +uvaca_stork MACH_UVACA_STORK UVACA_STORK 2533 +smartq5 MACH_SMARTQ5 SMARTQ5 2534 +all3078 MACH_ALL3078 ALL3078 2535 +ctera_2bay_ds MACH_CTERA_2BAY_DS CTERA_2BAY_DS 2536 +siogentoo3 MACH_SIOGENTOO3 SIOGENTOO3 2537 +epb5000 MACH_EPB5000 EPB5000 2538 +hy9263 MACH_HY9263 HY9263 2539 +acer_tempo_m900 MACH_ACER_TEMPO_M900 ACER_TEMPO_M900 2540 +acer_tempo_dx650 MACH_ACER_TEMPO_DX900 ACER_TEMPO_DX900 2541 +acer_tempo_x960 MACH_ACER_TEMPO_X960 ACER_TEMPO_X960 2542 +acer_eten_v900 MACH_ACER_ETEN_V900 ACER_ETEN_V900 2543 +acer_eten_x900 MACH_ACER_ETEN_X900 ACER_ETEN_X900 2544 +bonnell MACH_BONNELL BONNELL 2545 +oht_mx27 MACH_OHT_MX27 OHT_MX27 2546 +htcquartz MACH_HTCQUARTZ HTCQUARTZ 2547 +davinci_dm6467tevm MACH_DAVINCI_DM6467TEVM DAVINCI_DM6467TEVM 2548 +c3ax03 MACH_C3AX03 C3AX03 2549 +mxt_td60 MACH_MXT_TD60 MXT_TD60 2550 +esyx MACH_ESYX ESYX 2551 +bulldog MACH_BULLDOG BULLDOG 2553 -- cgit v1.2.3